flashrom

flashrom@flashrom.org

8 participants
9164 discussions

Report: Dell 0Y2MRG A06 read
by dpcimanager＠users.sourceforge.net 04 Apr '13

04 Apr '13

flashrom v0.9.6.1-r1653 on Darwin 12.3.0 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.10, LLVM Clang 4.2 (clang-425.0.24), little endian Command line (5 args): /Applications/DPCIManager.app/Contents/MacOS/flashrom -VV -r ~/Desktop/Dell 0Y2MRG A06.rom -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 519M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1009 us, 10000 myus = 10353 us, 4 myus = 4 us, OK. Initializing internal programmer Mapping low megabyte at 0x00000400, unaligned size 0xffc00. Mapping low megabyte, 0xffc00 bytes at unaligned 0x00000400. No coreboot table found. DMI string system-manufacturer: "Dell Inc." DMI string system-product-name: "XPS 8300 " DMI string system-version: " " DMI string baseboard-manufacturer: "Dell Inc." DMI string baseboard-product-name: "0Y2MRG" DMI string baseboard-version: "A00" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8772 on port 0x2e Found chipset "Intel H67" with PCI ID 8086:1c4a. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled Root Complex Register Block address = 0xfed1c000 GCS = 0xc00: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x0019a054 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write. 0x5C: 0x017f0001 FREG2: Warning: Management Engine region (0x00001000-0x0017ffff) is locked. 0x60: 0x00000fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x00000fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0x80 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0xf94010 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=0, SME=0, SCF=1 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00002005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x02040003 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 3 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x09300023 FLILL 0x00000000 --- Details --- Component 1 density: 4 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x03ff0180 FLREG2 0x017f0001 FLREG3 0x00000fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00180000 - 0x003fffff Region 2 (ME ) 0x00001000 - 0x0017ffff Region 3 (GbE ) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw SPI Read Configuration: prefetching disabled, caching enabled, OK. Super I/O ID 0x8772 is not on the list of flash capable controllers. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F512, 64 kB: program_opcodes: preop=5006 optype=460b opmenu=05150302c79f0190 on-the-fly OPCODE (0x15) re-programmed, op-pos=2 probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512A, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F1024(A), 128 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F2048, 256 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F4096, 512 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L2005(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L4005(A/C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L8005/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25LF080(A), 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Found Winbond flash chip "W25Q32" (4096 kB, SPI) at physical address 0xffc00000. Chip status register is 0x00. Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 SFDP revision = 1.1 SFDP number of parameter headers is 1 (NPH = 0). SFDP parameter table header 0/0: ID 0xef, version 1.0 Length 16 B, Parameter Table Pointer 0x000080 ID of the mandatory JEDEC SFDP parameter table is not 0 as demanded by JESD216 (warning only). Parsing JEDEC flash parameter table... 3-Byte only addressing. Status register is non-volatile and the standard does not allow vendors to tell us whether EWSR/WREN is needed for status register writes - assuming EWSR. Write chunk size is at least 64 B. Flash chip size is 4096 kB. Block eraser 0: 1024 x 4096 B with opcode 0x20 It seems like this chip supports the preliminary Intel version of SFDP, skipping processing of double words 3-9. done. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xf1, id2 0xaf, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xf1, id2 0xaf, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q32" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Block protection is disabled. Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0x1062c68a0 Restoring MMIO space at 0x1062c689c Restoring MMIO space at 0x1062c6898 Restoring MMIO space at 0x1062c6896 Restoring MMIO space at 0x1062c6894 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

can't write BISO chip of MSI Wind U100
by Daniel 03 Apr '13

03 Apr '13

flashrom v0.9.6.1-r1563 on Linux 3.5.0-26-generic (i686) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (5 args): flashrom --programmer internal -v -L -V Calibrating delay loop... OS timer resolution is 1 usecs, 809M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 1074 us, 10000 myus = 10580 us, 4 myus = 8 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MICRO-STAR INTERNATIONAL CO., LTD" DMI string system-product-name: "U90/U100" DMI string system-version: "Ver.001" DMI string baseboard-manufacturer: "MICRO-STAR INTERNATIONAL CO., LTD" DMI string baseboard-product-name: "U90/U100" DMI string baseboard-version: "Ver.001" DMI string chassis-type: "Desktop" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 00. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found chipset "Intel ICH7M" with PCI ID 8086:27b9. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 Root Complex Register Block address = 0xfed20000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (LPC) Top Swap : not enabled OK. The following protocols are supported: FWH. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xe1, id2 0xb8, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x01, id2 0x44, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x01, id2 0x44, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x02, id2 0x01, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x71, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically.

2 1

Re: [flashrom] AMD - SP5100 - take SPI ownership (1/2)
by Rudolf Marek 02 Apr '13

02 Apr '13

Hi, Found chipset "AMD SB7x0/SB8x0/SB9x0" with PCI ID 1002:439d. Enabling flash write... EC SIO is at 0x16e EC MBOX is at 0x3e (Shutting down IMC) SPI base address is at 0xfec10000 This means that firmware correctly responded to the command and most likely moved itself to internal RAM. Verifying flash... VERIFIED. EC SIO is at 0x16e EC MBOX is at 0x3e (IMC resume failed!) This means that firmware was not able to continue at the end? I have a couple of questions: 1) did you perform full power cycle (even unplugging the PSU)? I suspect that the IMC may run even if main cpu is off. I also suspect it fully initializes only if performing this "cold boot". 2) what was the update? It was from original BIOS to coreboot? Does coreboot have a embedded IMC image? Does the IMC image start at the same location? What we could additionally check is if the IMC firmware location does not match in source and dest image, bail out. Or if the base addr has been changed. Thanks Rudolf

2 1

Re: [flashrom] NM10 and SPI
by Stefan Tauner 02 Apr '13

02 Apr '13

On Tue, 2 Apr 2013 17:47:19 +0400 Vasiliy Vylegzhanin <coder(a)npo-echelon.ru> wrote: > Hello, > > I have a tablet on NM10 chipset and AFU says it has EON 25F/Q/QH chip > 16Mbit size. But flashrom don't even probe for SPI chips. > > > GCS = 0x10c60: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (LPC) > > Is it possible to force SPI interface somehow? Verbose log attached. Since the lockdown is disabled one could in theory change the interface used I think (I have never looked into it in detail). *But* this would not help you: the flash chip is most probably behind the embedded controller which is not supported yet by flashrom. The EC translates between the SPI bus used by the flash chip and the LPC bus used by the NM10. It also probably uses the same flash for its own firmware, which is one of the reasons why supporting such devices is a bit hairy. See also http://flashrom.org/Laptops -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

NM10 and SPI
by Vasiliy Vylegzhanin 02 Apr '13

02 Apr '13

Hello, I have a tablet on NM10 chipset and AFU says it has EON 25F/Q/QH chip 16Mbit size. But flashrom don't even probe for SPI chips. > GCS = 0x10c60: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (LPC) Is it possible to force SPI interface somehow? Verbose log attached.

1 0

Re: [flashrom] [PATCH 1/5] rayer_spi: Create list of programmer types
by Kyösti Mälkki 02 Apr '13

02 Apr '13

-------- Forwarded Message -------- From: Andrew Tarabaras <andytara12(a)gmail.com> To: Kyösti Mälkki <kyosti.malkki(a)gmail.com> Subject: Re: [PATCH 1/5] rayer_spi: Create list of programmer types Date: Tue, 2 Apr 2013 13:21:09 +1100 Hi Kyösti, I finally got to testing and it works fine. I used a xilinx buffered DLC5 Parallel 3 cable with rayer_spi driver. I also programmed an unsupported SPI Eprom. a PMC PM25LD010, I just copied the PM25LV010 definition and renamed it to PM25LD010 and read / write / erase is verified to work. I would like to contribute more but I just dont have the time to be submitting patches. Best Regards Andrew On Fri, Mar 8, 2013 at 3:39 AM, Andrew Tarabaras <andytara12(a)gmail.com> wrote: Hi, Forgot to get back to your last email. Sorry. I will test it in a few days. Regards Andrew On 08/03/2013 3:18 AM, "Kyösti Mälkki" <kyosti.malkki(a)gmail.com> wrote: Hi It would be great if you can test the updated patchset with new rayer_spi pinouts on actual hardware. https://bitbucket.org/kmalkki/flashrom/get/rayer_spi.tar.bz2 or git clone -b rayer_spi https://bitbucket.org/kmalkki/flashrom.git Thanks, Kyösti

2 1

Intel H61 locked board
by radocea bogdan 01 Apr '13

01 Apr '13

Hi. Here is another locked board (I attached the log too): sudo flashrom --programmer=internal -VV flashrom v0.9.6.1-runknown on Linux 3.7.0-7-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.2, little endian Command line (2 args): flashrom --programmer=internal -VV Calibrating delay loop... OS timer resolution is 1 usecs, 3207M loops per second, 10 myus = 10 us, 100 myus = 115 us, 1000 myus = 1022 us, 10000 myus = 10029 us, 4 myus = 11 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Dell Inc." DMI string system-product-name: "Inspiron 620 " DMI string system-version: "00" DMI string baseboard-manufacturer: "Dell Inc." DMI string baseboard-product-name: "0GDG8Y " DMI string baseboard-version: "A00" DMI string chassis-type: "Desktop" Found chipset "Intel H61" with PCI ID 8086:1c5c. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled Root Complex Register Block address = 0xfed1c000 GCS = 0xc00: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write. 0x5C: 0x017f0001 FREG2: Warning: Management Engine region (0x00001000-0x0017ffff) is locked. 0x60: 0x00001fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x00001fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf84130 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=3, DBC=1, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00002005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x02040003 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 3 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x09300013 FLILL 0x00000000 --- Details --- Component 1 density: 4 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x03ff0180 FLREG2 0x017f0001 FLREG3 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00180000 - 0x003fffff Region 2 (ME ) 0x00001000 - 0x0017ffff Region 3 (GbE ) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw SPI Read Configuration: prefetching disabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25F512, 64 kB: program_opcodes: preop=5006 optype=460b opmenu=05150302c79f0190 on-the-fly OPCODE (0x15) re-programmed, op-pos=2 probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512A, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25F1024(A), 128 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F2048, 256 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F4096, 512 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L2005(C), 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L4005(A/C), 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L8005/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1605A/MX25L1606E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1605D/MX25L1608D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Found Macronix flash chip "MX25L3205(A)" (4096 kB, SPI) at physical address 0xffc00000. Chip status register is 0x00. Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Found Macronix flash chip "MX25L3205D/MX25L3208D" (4096 kB, SPI) at physical address 0xffc00000. Chip status register is 0x00. Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Probing for Macronix MX25L3206E, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Found Macronix flash chip "MX25L3206E" (4096 kB, SPI) at physical address 0xffc00000. Chip status register is 0x00. Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Multiple flash chips were detected: "MX25L3205(A)", "MX25L3205D/MX25L3208D", "MX25L3206E" Please specify which chip to use with the -c <chipname> option. Restoring MMIO space at 0x7f1b2b5588a0 Restoring MMIO space at 0x7f1b2b55889c Restoring MMIO space at 0x7f1b2b558898 Restoring MMIO space at 0x7f1b2b558896 Restoring MMIO space at 0x7f1b2b558894 Restoring PCI config space for 00:1f:0 reg 0xdc Please let me know if I can write to this board. Thanks -- Radocea Bogdan System Admin, BetBrain BetBrain — Odds on your side iGB Best Sportsbook Affiliate 2008, 2009 & 2010 London — Bucharest — Copenhagen — Changsha — Oslo Telephone: +40735194165 Address: 5 Sirenelor Street, Sector 5, 050855 Bucharest, Romania E-Mail: rbp(a)betbrain.com Skype: radocea_bogdan

1 0

[PATCH 2/2] Add support for PMC Pm25LD series.
by Stefan Tauner 01 Apr '13

01 Apr '13

This patch adds support for - Pm25LD256C - Pm25LD512(C) - Pm25LD010(C) - Pm25LD020(C) - Pm25LD040(C) These seem to be the successors of the Pm25LV series. The main difference seems to be the dual I/O and additional erase opcodes. Some support an additional, complex locking register (maybe all of the above, but available datahsheets do not indicate it for all). Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- flashchips.c | 189 +++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 7 +- spi25_statusreg.c | 1 + 3 files changed, 196 insertions(+), 1 deletion(-) diff --git a/flashchips.c b/flashchips.c index 342fcea..37167e6 100644 --- a/flashchips.c +++ b/flashchips.c @@ -6562,6 +6562,195 @@ const struct flashchip flashchips[] = { { .vendor = "PMC", + .name = "Pm25LD256C", + .bustype = BUS_SPI, + .manufacture_id = PMC_ID, + .model_id = PMC_PM25LD256C, + .total_size = 32, + .page_size = 256, + .feature_bits = FEATURE_WRSR_WREN, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 8} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {4 * 1024, 8} }, + .block_erase = spi_block_erase_d7, + }, { + .eraseblocks = { {32 * 1024, 1} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {32 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {32 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_default_bp2, + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ + .voltage = {2700, 3600}, + }, + { + .vendor = "PMC", + .name = "Pm25LD512(C)", + .bustype = BUS_SPI, + .manufacture_id = PMC_ID, + .model_id = PMC_PM25LD512, + .total_size = 64, + .page_size = 256, + .feature_bits = FEATURE_WRSR_WREN, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 16} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {4 * 1024, 16} }, + .block_erase = spi_block_erase_d7, + }, { + .eraseblocks = { {32 * 1024, 2} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_default_bp2, + .unlock = spi_disable_blockprotect, /* FIXME: C version supports "Safe Guard" */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "PMC", + .name = "Pm25LD010(C)", + .bustype = BUS_SPI, + .manufacture_id = PMC_ID, + .model_id = PMC_PM25LD010, + .total_size = 128, + .page_size = 256, + .feature_bits = FEATURE_WRSR_WREN, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 32} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {4 * 1024, 32} }, + .block_erase = spi_block_erase_d7, + }, { + .eraseblocks = { {32 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {128 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {128 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_default_bp2, + .unlock = spi_disable_blockprotect, /* FIXME: C version supports "Safe Guard" */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ + .voltage = {2700, 3600}, /* 2.3-3.6V for Pm25LD010 */ + }, + + { + .vendor = "PMC", + .name = "Pm25LD020(C)", + .bustype = BUS_SPI, + .manufacture_id = PMC_ID, + .model_id = PMC_PM25LD020, + .total_size = 256, + .page_size = 256, + .feature_bits = FEATURE_WRSR_WREN, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = spi_block_erase_d7, + }, { + .eraseblocks = { {64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_default_bp2, + .unlock = spi_disable_blockprotect, /* FIXME: C version supports "Safe Guard" */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ + .voltage = {2700, 3600}, /* 2.3-3.6V for Pm25LD020 */ + }, + + { + .vendor = "PMC", + .name = "Pm25LD040(C)", + .bustype = BUS_SPI, + .manufacture_id = PMC_ID, + .model_id = PMC_PM25LV040, + .total_size = 512, + .page_size = 256, + .feature_bits = FEATURE_WRSR_WREN, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = spi_block_erase_d7, + }, { + .eraseblocks = { {64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_default_bp2, + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ + .voltage = {2700, 3600}, /* 2.3-3.6V for Pm25LD040 */ + }, + + { + .vendor = "PMC", .name = "Pm25LV512", .bustype = BUS_SPI, .manufacture_id = PMC_ID_NOPREFIX, diff --git a/flashchips.h b/flashchips.h index bbad7ec..4da4868 100644 --- a/flashchips.h +++ b/flashchips.h @@ -450,13 +450,18 @@ /* * Programmable Micro Corp is listed in JEP106W in bank 2, so it should * have a 0x7F continuation code prefix. + * Apparently this name is owned by "Chingis Technology Corporation" http://www.chingistek.com. */ #define PMC_ID 0x7F9D /* PMC */ #define PMC_ID_NOPREFIX 0x9D /* PMC, missing 0x7F prefix */ +#define PMC_PM25LD256C 0x2F +#define PMC_PM25LD512 0x20 /* Same as Pm25LD512C, but the latter has more locking options. */ +#define PMC_PM25LD010 0x21 /* Same as Pm25LD010C, but the latter has more locking options. */ +#define PMC_PM25LD020 0x22 /* Same as Pm25LD020C, but the latter has more locking options. */ #define PMC_PM25LV512 0x7B /* Same as Pm25LV512A, but the latter does not support any sane probing. */ #define PMC_PM25LV010 0x7C /* Same as Pm25LV010A, but the latter uses the continuation prefix. */ #define PMC_PM25LV020 0x7D -#define PMC_PM25LV040 0x7E +#define PMC_PM25LV040 0x7E /* Same as PM25LD040(C), but the latter supports more features. */ #define PMC_PM25LV080B 0x13 #define PMC_PM25LV016B 0x14 #define PMC_PM29F002T 0x1D diff --git a/spi25_statusreg.c b/spi25_statusreg.c index c089157..53952fe 100644 --- a/spi25_statusreg.c +++ b/spi25_statusreg.c @@ -262,6 +262,7 @@ int spi_prettyprint_status_register_default_bp1(struct flashctx *flash) /* Works for many chips of the * AMIC A25L series + * PMC Pm25LD series */ int spi_prettyprint_status_register_default_bp2(struct flashctx *flash) { -- Kind regards, Stefan Tauner

1 0

help
by Pinery. 01 Apr '13

01 Apr '13

hello! my,, EEPROM ID (7F,9D20) : PMC Pm25Ld512 2.7-3.6V 512Kx1S, page This can support ? Thank you!

2 2

Re: [flashrom] [PATCH] Refine granularity handling in preparation of AT45DB series support.
by Carl-Daniel Hailfinger 01 Apr '13

01 Apr '13

Hi Mark, allow me to explain. You may want to run away screaming and I can't blame you. page_size is a historical concept in flashrom created when flashrom was an ad-hoc collection of flashing routines for maybe 5 chips. It had a number of different meanings depending on the chip with no clear rules whatsoever. We even abused it for erase block sizes and block locking. It doesn't help that datasheets have verying definitions of the meaning of page size as well. A flash chip has certain write/erase/read properties, and those differ between NAND and NOR flash. Right now flashrom only supports NOR flash with certain characteristics (power-of-two sizes for min write size / max write size / chip size). The growing pains start with Atmel AT45* chips which are different. Properties of a flash chip: - Total size (Must be a multiple of 1024 bytes right now, easily fixable.) - Erase block sizes (Arbitrary sizes and multiple erase methods are supported for that, no need to change anything.) - Addressing -- Address size (3-byte vs. 4-byte addresses for SPI flash. Patches exist, have to be reviewed.) -- Address space contiguousness (Does the address space have holes? Are holes present in the read result if someone does a read/write from address A to B with an address space hole in the middle?) -- Address granularity (Can individual bytes be addressed directly or is there a need for sub-addresses like byte selection for old 16-bit word parallel flash?) - Reading -- Maximum read size -- Minimum read size (Can individual bytes be read from the chip like for most NOR flash?) - Writing (Multiple write methods, characteristics below are per-method.) -- Maximum write size in one meta-command (Meta-command is a single command for unrelated write commands or group of related write commands for stuff like AAI with a begin and end command.) -- Maximum (or fixed) write size in one sub-command (Sub-command is a single command for unrelated write commands or a single command for stuff like AAI.) -- Minimum write size (Minimum number of bits/bytes to be written so that no undefined results happen.) -- Write wraparound (Whether writes starting in the middle of a "page" wrap around to the start of the page, this is avoided in flashrom code and thus not relevant here.) - Block locking (Not directly relevant to this discussion except that we abused page_size for that in the past.) - Command set (Not relevant except for commands needed for above properties.) - Buses (Not relevant here.) - Voltage (Not relevant here.) - Timing (Not relevant here.) At various times during flashrom development, page_size has been used for pretty much every single item listed above. Some strange uses remain. Let me illustrate the properties above with a few sample chips: ST/Numonyx/Micron M25P32: (no surprises) - Total size: 4096 kByte - Erase block sizes: 64 kByte for command 0xd8, 4 MByte for command 0xc7 - Addressing -- Address size: 3-Byte -- Address space contiguousness: No holes -- Address granularity: Direct Byte access - Reading -- Minimum read size: 1 Byte -- Maximum read size: unlimited - Writing: Only one write method: Page write -- Maximum write size in one meta-command: 256 Bytes -- Maximum (or fixed) write size in one sub-command: 256 Bytes -- Minimum write size: 1 Byte Micron N25Q256: (4-byte addresses) - Total size: 32 MByte - Erase block sizes: 4 kByte for command 0x20, 64 kByte for command 0xd8, 32 MByte for command 0xc7 - Addressing -- Address size: 3-byte with Extended Address register for upper bit or 4-byte, switchable with Flag Status Register and/or command set -- Address space contiguousness: No holes -- Address granularity: Direct byte access - Reading -- Minimum read size: 1 byte -- Maximum read size: unlimited (unless non-default wrap mode is active) - Writing: -- Maximum write size in one meta-command: 256 Bytes -- Maximum (or fixed) write size in one sub-command: 256 Bytes -- Minimum write size: 1 Byte Atmel AT45DB041D (256-byte page mode): - Total size: 512 kByte - Erase block sizes: 256 Byte for command 0x81, 2 kByte for command 0x50, 2/64 kByte for command 0x7c (not all regions erasable), 512 kByte for command 0xc794809a - Addressing -- Address size: 3-byte -- Address space contiguousness: No holes -- Address granularity: Direct byte access (other options exist) - Reading -- Minimum read size: 1 Byte -- Maximum read size: unlimited - Writing: -- Maximum write size in one meta-command: 256 Bytes -- Maximum (or fixed) write size in one sub-command: 256 Bytes -- Minimum write size: 256 Bytes (unusual for other SPI chips) Atmel AT45DB041D (264-byte page mode): - Total size: 528 kByte - Erase block sizes: 264 Byte for command 0x81, 2112 Byte for command 0x50, 2112/67584 Byte for command 0x7c (not all regions erasable), 528 kByte for command 0xc794809a - Addressing -- Address size: 3-byte -- Address space contiguousness: With holes -- Address granularity: Direct byte access (other options exist) - Reading -- Minimum read size: 1 Byte (mind the holes in address space) -- Maximum read size: unlimited (mind the holes in address space for initial address, but the read result will have no holes even for reads spanning holes) - Writing: -- Maximum write size in one meta-command: 264 Bytes -- Maximum (or fixed) write size in one sub-command: 264 Bytes -- Minimum write size: 264 Bytes (unusual for other SPI chips) SST SST25VF016B: (AAI) - Total size: 2048 kByte - Erase block sizes: 4 kByte for command 0x20, 32 kByte for command 0x52, 64 kByte for command 0xd8, 2 MByte for commands 0x60/0xc7 - Addressing -- Address size: 3-Byte -- Address space contiguousness: No holes -- Address granularity: Direct Byte access - Reading -- Minimum read size: 1 Byte -- Maximum read size: unlimited - Writing: Write method: Byte write -- Maximum write size in one meta-command: 1 Byte -- Maximum (or fixed) write size in one sub-command: 1 Byte -- Minimum write size: 1 Byte - Writing: Write method: AAI write -- Maximum write size in one meta-command: 2097152 Bytes (chip size) -- Maximum (or fixed) write size in one sub-command: 2 Bytes -- Minimum write size: 2 Bytes The "write_granularity" we have in our tree is the minimum write size. Depending on the datasheet author, "page size" can be a minimum write size, maximum write size, minimum read size, maximum read size or largest contiguous chunk in the address space. The most prudent thing would probably be to rename chip->gran to chip->write_min_size, as well as add veriables chip->write_max_size and chip->address_holes_after (264 bytes for AT45DB041D in 264-byte page mode). We'll also need a function chip->linear_to_physical_address function. I'll try to answer your questions below. Am 28.03.2013 11:41 schrieb Mark Marshall: > I'm currently struggling to understand what the write granularity is for > and how it > interacts with the page size? > I'm also a little confused by flashrom's use of page size? > > I am mainly interested in SPI flash chips. For most SPI chips the "page > size" is 256 bytes. > I have a chip where the page size is 512 bytes. > > The "page size" is the amount that writes using the PP command have to be > chunked by. > So "spi_nbyte_program" must be used to write no more than "page size" bytes > and must > not cross a "page size" boundary. Yes. With my new terminology, this would be write_max_size instead of page_size. > So far this all makes sense, apart from the "spi_chip_write_256" function, > which should > be named "spi_chip_write_page"? (as all chips currently have a page size > of 256 this is > correct at the moment, but I'm about to add one that doesn't). Correct. > I think that the "chunksize" parameter in spi_write_chunked is to do with > possible restrictions > of some programmer hardware? This also makes sense, apart from all of the > comments which > are very out of date? Yes. > According to the manuals of the SPI Flash chips I've looked at, when using > the PP command > you can program any part of a page, and the correct thing will happen (1's > can only be written > to 0's). So I don't see how this matches up with "write granularity", > which claims that the other > bytes in the granularity region will be "undefined"? If you can write a single byte multiple times as long as you never try to set a 0 bit to 1, you have 1-bit granularity. If you can write a single byte just once, you have 1-byte granularity. If you can only write multiple bytes at once (e.g. 264 bytes for AT45* in some modes) and non-written bytes of a "page" end up undefined, you have n-byte granularity. > Is write granularity for something else? No, it's just really complicated. > Is there a post somewhere that I missed that explains all of this? No post anywhere, and your mail prompted me to write something up. Hope it helped. Regards, Carl-Daniel -- http://www.hailfinger.org/

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom