flashrom October 2013

flashrom@flashrom.org

22 participants
121 discussions

[PATCH] serial: use internal_delay
by Urja Rannikko 19 Oct '13

19 Oct '13

Using programmer_delay when serial is being used, could cause a major recursion (and breakage of the serial protocol). This has not been noticed because apparently all serial drivers used appear to always write >0 bytes, but still... Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> --- serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/serial.c b/serial.c index 4d912ba..126079a 100644 --- a/serial.c +++ b/serial.c @@ -357,7 +357,7 @@ int serialport_write(unsigned char *buf, unsigned int writecnt) if (!tmp) { msg_pdbg2("Empty write\n"); empty_writes--; - programmer_delay(500); + internal_delay(500); if (empty_writes == 0) { msg_perr("Serial port is unresponsive!\n"); return 1; -- 1.8.4

2 1

[commit] r1759 - trunk
by repository service 19 Oct '13

19 Oct '13

Author: stefanct Date: Sun Oct 20 01:35:28 2013 New Revision: 1759 URL: http://flashrom.org/trac/flashrom/changeset/1759 Log: serial: use internal_delay() for timeouts. Using programmer_delay() for timeouts in serial writes could cause a (theoretically) endless recursion if serial communication is used to send the programmer the delay command to be executed on the programmer instead of the host which fails again, following a timeout which sends... Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/serial.c Modified: trunk/serial.c ============================================================================== --- trunk/serial.c Sun Oct 20 01:09:16 2013 (r1758) +++ trunk/serial.c Sun Oct 20 01:35:28 2013 (r1759) @@ -357,7 +357,7 @@ if (!tmp) { msg_pdbg2("Empty write\n"); empty_writes--; - programmer_delay(500); + internal_delay(500); if (empty_writes == 0) { msg_perr("Serial port is unresponsive!\n"); return 1;

1 0

Re: [flashrom] [PATCH] Add support for SST25VF512A
by Stefan Tauner 19 Oct '13

19 Oct '13

On Tue, 15 Oct 2013 15:30:00 -0400 Cory Henderson <dcoryh192(a)gmail.com> wrote: > Hi, > > I am new to the mailing list so I am not sure if this is the right place > for these. My company used the SST25VF512A in a project and I was able to > configure flashrom to work with this chip using a buspirate (HW v3.5, FW > v6.2 beta). The chip was already listed in flashchips.h so I just added the > proper information to flashchips.c. Probe, read, write, and erase all work > fine for me, albeit slowly because the AAI supported by the chip uses a > different command than the one used in flashrom. > > Cory Henderson Hello Cory and thanks for your patch! There were a few tiny problems: - white space error (lonely tab in an otherwise empty line), - spi_prettyprint_status_register_sst25 is not completely correct (chip does not have bp2 and bp3), - wrong order within flashchips.c which is understandable because others of the family were wrong too, - maybe I forgot something else, but in general it looked good, thanks again. I just *had* to add two other chips which were missing, and refine a few comments of others... when reviewing the code, before committing it in r1758. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[commit] r1758 - trunk
by repository service 19 Oct '13

19 Oct '13

Author: stefanct Date: Sun Oct 20 01:09:16 2013 New Revision: 1758 URL: http://flashrom.org/trac/flashrom/changeset/1758 Log: Refine support for SST25VF family. - Reorder some models and refine comments. - Add SST25VF512A: AAI is available but with an uncommon opcode (0xAF). Fully tested with Bus Pirate 3.5 running 6.2 beta firmware by Cory. - Add SST25VF020 and SST25VF020B. Signed-off-by: Cory Henderson <dcoryh192(a)gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/flashchips.c trunk/flashchips.h Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Wed Oct 2 03:22:17 2013 (r1757) +++ trunk/flashchips.c Sun Oct 20 01:09:16 2013 (r1758) @@ -9551,11 +9551,11 @@ { .vendor = "SST", - .name = "SST25VF010", + .name = "SST25VF512A", .bustype = BUS_SPI, .manufacture_id = SST_ID, - .model_id = SST_SST25VF010_REMS, - .total_size = 128, + .model_id = SST_SST25VF512A_REMS, + .total_size = 64, .page_size = 256, .feature_bits = FEATURE_WRSR_EWSR, .tested = TEST_OK_PREW, @@ -9564,134 +9564,134 @@ .block_erasers = { { - .eraseblocks = { {4 * 1024, 32} }, + .eraseblocks = { {4 * 1024, 16} }, .block_erase = spi_block_erase_20, }, { - .eraseblocks = { {32 * 1024, 4} }, + .eraseblocks = { {32 * 1024, 2} }, .block_erase = spi_block_erase_52, }, { - .eraseblocks = { {128 * 1024, 1} }, + .eraseblocks = { {32 * 1024, 2} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {64 * 1024, 1} }, .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_c7, }, }, - .printlock = spi_prettyprint_status_register_sst25, /* TODO: check */ + .printlock = spi_prettyprint_status_register_sst25, /* FIXME: No BP2 & 3 */ .unlock = spi_disable_blockprotect, - .write = spi_chip_write_1, - .read = spi_chip_read, + .write = spi_chip_write_1, /* AAI supported, but opcode is 0xAF */ + .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, }, { .vendor = "SST", - .name = "SST25VF016B", + .name = "SST25VF010", .bustype = BUS_SPI, .manufacture_id = SST_ID, - .model_id = SST_SST25VF016B, - .total_size = 2048, + .model_id = SST_SST25VF010_REMS, + .total_size = 128, .page_size = 256, - .feature_bits = FEATURE_WRSR_EITHER, + .feature_bits = FEATURE_WRSR_EWSR, .tested = TEST_OK_PREW, - .probe = probe_spi_rdid, + .probe = probe_spi_rems, .probe_timing = TIMING_ZERO, .block_erasers = { { - .eraseblocks = { {4 * 1024, 512} }, + .eraseblocks = { {4 * 1024, 32} }, .block_erase = spi_block_erase_20, }, { - .eraseblocks = { {32 * 1024, 64} }, + .eraseblocks = { {32 * 1024, 4} }, .block_erase = spi_block_erase_52, }, { - .eraseblocks = { {64 * 1024, 32} }, + .eraseblocks = { {32 * 1024, 4} }, .block_erase = spi_block_erase_d8, }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, + .eraseblocks = { {128 * 1024, 1} }, .block_erase = spi_block_erase_60, }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, + .eraseblocks = { {128 * 1024, 1} }, .block_erase = spi_block_erase_c7, }, }, - .printlock = spi_prettyprint_status_register_sst25vf016, + .printlock = spi_prettyprint_status_register_sst25, /* FIXME: No BP2 & 3 */ .unlock = spi_disable_blockprotect, - .write = spi_aai_write, - .read = spi_chip_read, + .write = spi_chip_write_1, /* AAI supported, but opcode is 0xAF */ + .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, }, { .vendor = "SST", - .name = "SST25VF032B", + .name = "SST25VF020", .bustype = BUS_SPI, .manufacture_id = SST_ID, - .model_id = SST_SST25VF032B, - .total_size = 4096, + .model_id = SST_SST25VF020_REMS, + .total_size = 256, .page_size = 256, .feature_bits = FEATURE_WRSR_EWSR, - .tested = TEST_OK_PREW, - .probe = probe_spi_rdid, + .tested = TEST_UNTESTED, + .probe = probe_spi_rems, .probe_timing = TIMING_ZERO, .block_erasers = { { - .eraseblocks = { {4 * 1024, 1024} }, + .eraseblocks = { {4 * 1024, 64} }, .block_erase = spi_block_erase_20, }, { - .eraseblocks = { {32 * 1024, 128} }, + .eraseblocks = { {32 * 1024, 8} }, .block_erase = spi_block_erase_52, }, { - .eraseblocks = { {64 * 1024, 64} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {4 * 1024 * 1024, 1} }, + .eraseblocks = { {256 * 1024, 1} }, .block_erase = spi_block_erase_60, - }, { - .eraseblocks = { {4 * 1024 * 1024, 1} }, - .block_erase = spi_block_erase_c7, }, }, - .printlock = spi_prettyprint_status_register_sst25, /* TODO: check */ + .printlock = spi_prettyprint_status_register_sst25, /* FIXME: No BP2 & 3 */ .unlock = spi_disable_blockprotect, - .write = spi_aai_write, - .read = spi_chip_read, + .write = spi_chip_write_1, /* AAI supported, but opcode is 0xAF */ + .read = spi_chip_read, /* only */ .voltage = {2700, 3600}, }, { .vendor = "SST", - .name = "SST25VF064C", + .name = "SST25VF020B", .bustype = BUS_SPI, .manufacture_id = SST_ID, - .model_id = SST_SST25VF064C, - .total_size = 8192, + .model_id = SST_SST25VF020B, + .total_size = 256, .page_size = 256, .feature_bits = FEATURE_WRSR_EWSR, - .tested = TEST_OK_PREW, + .tested = TEST_UNTESTED, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { - .eraseblocks = { {4 * 1024, 2048} }, + .eraseblocks = { {4 * 1024, 64} }, .block_erase = spi_block_erase_20, }, { - .eraseblocks = { {32 * 1024, 256} }, + .eraseblocks = { {32 * 1024, 8} }, .block_erase = spi_block_erase_52, }, { - .eraseblocks = { {64 * 1024, 128} }, + .eraseblocks = { {64 * 1024, 4} }, .block_erase = spi_block_erase_d8, }, { - .eraseblocks = { {8 * 1024 * 1024, 1} }, + .eraseblocks = { {256 * 1024, 1} }, .block_erase = spi_block_erase_60, }, { - .eraseblocks = { {8 * 1024 * 1024, 1} }, + .eraseblocks = { {256 * 1024, 1} }, .block_erase = spi_block_erase_c7, }, }, - .printlock = spi_prettyprint_status_register_sst25, /* TODO: check */ - .unlock = spi_disable_blockprotect, - .write = spi_chip_write_256, - .read = spi_chip_read, + .printlock = spi_prettyprint_status_register_sst25, /* FIXME: No BP2 & 3 and 2nd SR */ + .unlock = spi_disable_blockprotect, /* FIXME: 2nd SR */ + .write = spi_aai_write, /* AAI supported (0xAD) */ + .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, }, @@ -9760,8 +9760,8 @@ }, .printlock = spi_prettyprint_status_register_sst25vf040b, .unlock = spi_disable_blockprotect, - .write = spi_aai_write, - .read = spi_chip_read, + .write = spi_aai_write, /* AAI supported (0xAD) */ + .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, }, @@ -9840,6 +9840,120 @@ .read = spi_chip_read, .voltage = {2700, 3600}, }, + + { + .vendor = "SST", + .name = "SST25VF016B", + .bustype = BUS_SPI, + .manufacture_id = SST_ID, + .model_id = SST_SST25VF016B, + .total_size = 2048, + .page_size = 256, + .feature_bits = FEATURE_WRSR_EITHER, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 512} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 64} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 32} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + }, + }, + .printlock = spi_prettyprint_status_register_sst25vf016, + .unlock = spi_disable_blockprotect, + .write = spi_aai_write, + .read = spi_chip_read, + .voltage = {2700, 3600}, + }, + + { + .vendor = "SST", + .name = "SST25VF032B", + .bustype = BUS_SPI, + .manufacture_id = SST_ID, + .model_id = SST_SST25VF032B, + .total_size = 4096, + .page_size = 256, + .feature_bits = FEATURE_WRSR_EWSR, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 1024} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 128} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 64} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {4 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {4 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + }, + }, + .printlock = spi_prettyprint_status_register_sst25, /* TODO: check */ + .unlock = spi_disable_blockprotect, + .write = spi_aai_write, + .read = spi_chip_read, + .voltage = {2700, 3600}, + }, + + { + .vendor = "SST", + .name = "SST25VF064C", + .bustype = BUS_SPI, + .manufacture_id = SST_ID, + .model_id = SST_SST25VF064C, + .total_size = 8192, + .page_size = 256, + .feature_bits = FEATURE_WRSR_EWSR, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 2048} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 256} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 128} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {8 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {8 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + }, + }, + .printlock = spi_prettyprint_status_register_sst25, /* TODO: check */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {2700, 3600}, + }, { .vendor = "SST", Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Wed Oct 2 03:22:17 2013 (r1757) +++ trunk/flashchips.h Sun Oct 20 01:09:16 2013 (r1758) @@ -577,6 +577,7 @@ #define SST_SST25VF512A_REMS 0x48 /* REMS or RES opcode */ #define SST_SST25VF010_REMS 0x49 /* REMS or RES opcode */ #define SST_SST25VF020_REMS 0x43 /* REMS or RES opcode */ +#define SST_SST25VF020B 0x258C #define SST_SST25VF040_REMS 0x44 /* REMS or RES opcode, same as SST25LF040A */ #define SST_SST25VF040B 0x258D #define SST_SST25VF040B_REMS 0x8D /* REMS or RES opcode */

1 0

Re: [flashrom] MS-7030 Mainboard won't program BIOS chip model other than oryginal
by Stefan Tauner 18 Oct '13

18 Oct '13

On Fri, 18 Oct 2013 13:21:44 +0200 san <san(a)plusnet.pl> wrote: > Ok, case closed. > > Found answer here: http://forum-en.msi.com/index.php?topic=95357.0 > > quoting: > The difference between SST49LF004A and SST49LF004B is that the 4B version > supports LPC / FWH Flashing, 4A version can not handle this. > > I knew SOMETHING about this, but thought it is not my case. yes, very likely. > By the way, is it possible to add bios chip information (type) to support > list? What do you mean exactly? The interface type is noted in the wiki table as well as in the output of flashrom -L. For the chip in question on that nforce2 board i think it would not make any difference anyway if you would modify the bustype field in flashchips.c. > And how about 'soldering' write-enable? As in last link i found there is a > pad (#23) called "Write Enable". It might be possible to cut off this line > from motherboard solder 'programmable voltage', and program bioses on > not-enabled mainboards. Is that correct? In theory that is possible, but normally the pin is connected to a software-controlled pin (GPIO pin of the southbridge for example), and you are way better off controlling that pin with flashrom (a so-called board enable), than physically modifying a board. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] MS-7030 Mainboard won't program BIOS chip model other than oryginal
by san 18 Oct '13

18 Oct '13

Ok, case closed. Found answer here: http://forum-en.msi.com/index.php?topic=95357.0 quoting: The difference between SST49LF004A and SST49LF004B is that the 4B version supports LPC / FWH Flashing, 4A version can not handle this. I knew SOMETHING about this, but thought it is not my case. This might be useful information in FAQ. Also, more complete explanation might be found here: http://www.rom.by/Art_of_BIOS_flashing By the way, is it possible to add bios chip information (type) to support list? And how about 'soldering' write-enable? As in last link i found there is a pad (#23) called "Write Enable". It might be possible to cut off this line from motherboard solder 'programmable voltage', and program bioses on not-enabled mainboards. Is that correct? Best regards! 2013/10/17 san <san(a)plusnet.pl> > i propably should add verbose... > > > 2013/10/17 san <san(a)plusnet.pl> > >> Hi! >> >> Recently i bought mainboard compatible to flashrom.pinned oryginal bios >> (SST49LF004B) and other chips. >> I do not own exacly same chip, so i tried to replace with some i have: >> >> SST49LF004 / 4A (and smaller 2A and 3A) >> Intel 82802AB8 >> >> but no luck - i can not even read those. >> I replaced back the original chip and i am able to program modified bios. >> >> What is the problem? >> >> Best regards! >> >> -- >> [ e-San.info | San(a)plusnet.pl ] >> > > > > -- > [ e-San.info | San(a)plusnet.pl ] > -- [ e-San.info | San(a)plusnet.pl ]

1 0

Re: [flashrom] MS-7030 Mainboard won't program BIOS chip model other than oryginal
by san 17 Oct '13

17 Oct '13

i propably should add verbose... 2013/10/17 san <san(a)plusnet.pl> > Hi! > > Recently i bought mainboard compatible to flashrom.pinned oryginal bios > (SST49LF004B) and other chips. > I do not own exacly same chip, so i tried to replace with some i have: > > SST49LF004 / 4A (and smaller 2A and 3A) > Intel 82802AB8 > > but no luck - i can not even read those. > I replaced back the original chip and i am able to program modified bios. > > What is the problem? > > Best regards! > > -- > [ e-San.info | San(a)plusnet.pl ] > -- [ e-San.info | San(a)plusnet.pl ]

1 0

MS-7030 Mainboard won't program BIOS chip model other than oryginal
by san 17 Oct '13

17 Oct '13

Hi! Recently i bought mainboard compatible to flashrom.pinned oryginal bios (SST49LF004B) and other chips. I do not own exacly same chip, so i tried to replace with some i have: SST49LF004 / 4A (and smaller 2A and 3A) Intel 82802AB8 but no luck - i can not even read those. I replaced back the original chip and i am able to program modified bios. What is the problem? Best regards! -- [ e-San.info | San(a)plusnet.pl ]

1 0

unsupported BIOS BIOSTAR H77MU3
by Thomas Unger DE 17 Oct '13

17 Oct '13

Hello guys, I have here a unsupported BIOS in my main board. Maybe you can help me to use your amazing tool? Regards Thomas #### Verbose output #>flashrom -Vr bios.bin flashrom v0.9.5.2-r1530 on Linux 2.6.32-358.18.1.el6.x86_64 (x86_64), built with libpci 3.1.4, GCC 4.4.6 20110731 (Red Hat 4.4.6-3), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1582M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 999 us, 10000 myus = 9940 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "BIOSTAR Group" DMI string system-product-name: "H77MU3" DMI string system-version: "6.0" DMI string baseboard-manufacturer: "BIOSTAR Group" DMI string baseboard-product-name: "H77MU3" DMI string baseboard-version: "6.0" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8728 on port 0x2e Found chipset "Intel H77" with PCI ID 8086:1e4a. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... enable_flash_ich_dc_spi: unknown ICH generation. Please report! 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x8 Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (unknown) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00001000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write. 0x5C: 0x017f0001 FREG2: WARNING: Management Engine region (0x00001000-0x0017ffff) is locked. Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf90000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=1 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) SPI Read Configuration: prefetching enabled, caching enabled, OK. Super I/O ID 0x8728 is not on the list of flash capable controllers. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080A, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF010, 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Chip status register is 00 Found Winbond flash chip "W25Q32" (4096 kB, SPI) at physical address 0xffc00000. Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0x45, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xb5, id2 0xc2, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xb5, id2 0xc2, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xf9, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q32" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=1 Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0x7fdbc14fd8a0 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

[PATCH] Add support for SST25VF512A
by Cory Henderson 15 Oct '13

15 Oct '13

Hi, I am new to the mailing list so I am not sure if this is the right place for these. My company used the SST25VF512A in a project and I was able to configure flashrom to work with this chip using a buspirate (HW v3.5, FW v6.2 beta). The chip was already listed in flashchips.h so I just added the proper information to flashchips.c. Probe, read, write, and erase all work fine for me, albeit slowly because the AAI supported by the chip uses a different command than the one used in flashrom. Cory Henderson

1 0

← Newer
1
...
4
5
6
7
8
9
10
...
13
Older →

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom October 2013