September 2012 - flashrom - mail.coreboot.org

Re: [flashrom] [PATCH 2/2] Nvidia chipset enables: refactor setting bit 0 in 0x6d
by Stefan Tauner Sept. 4, 2012

Sept. 4, 2012

On Sun, 7 Aug 2011 06:36:00 +0200 stefan.tauner at student.tuwien.ac.at (Stefan Tauner) wrote: > Signed-off-by: Stefan Tauner <stefan.tauner at student.tuwien.ac.at> Refined, Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> and committed in r1592. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[commit] r1592 - trunk
by repository service Sept. 4, 2012

Sept. 4, 2012

Author: stefanct Date: Tue Sep 4 03:49:49 2012 New Revision: 1592 URL: http://flashrom.org/trac/flashrom/changeset/1592 Log: Nvidia chipset enables: refactor setting bit 0 in 0x6d. This patch also changes semantics: previously failing to set this was interpreted as a fatal error by enable_flash_ck804 and enable_flash_mcp55 although the output indicated otherwise. Also, in enable_flash_nvidia_nforce2 there was no check if settings the bit succeeds. Now all methods check for success and return ERROR_NONFATAL on failure. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/chipset_enable.c Modified: trunk/chipset_enable.c ============================================================================== --- trunk/chipset_enable.c Sat Sep 1 23:47:19 2012 (r1591) +++ trunk/chipset_enable.c Tue Sep 4 03:49:49 2012 (r1592) @@ -968,19 +968,33 @@ return ret; } -static int enable_flash_nvidia_nforce2(struct pci_dev *dev, const char *name) +/* sets bit 0 in 0x6d */ +static int enable_flash_nvidia_common(struct pci_dev *dev, const char *name) { - uint8_t tmp; - - rpci_write_byte(dev, 0x92, 0); + uint8_t old, new; - tmp = pci_read_byte(dev, 0x6d); - tmp |= 0x01; - rpci_write_byte(dev, 0x6d, tmp); + old = pci_read_byte(dev, 0x6d); + new = old | 0x01; + if (new == old) + return 0; + rpci_write_byte(dev, 0x6d, new); + if (pci_read_byte(dev, 0x6d) != new) { + msg_pinfo("Setting register 0x6d to 0x%02x on %s failed.\n", new, name); + return 1; + } return 0; } +static int enable_flash_nvidia_nforce2(struct pci_dev *dev, const char *name) +{ + rpci_write_byte(dev, 0x92, 0); + if (enable_flash_nvidia_common(dev, name)) + return ERROR_NONFATAL; + else + return 0; +} + static int enable_flash_ck804(struct pci_dev *dev, const char *name) { uint8_t old, new; @@ -1001,19 +1015,10 @@ } } - old = pci_read_byte(dev, 0x6d); - new = old | 0x01; - if (new == old) + if (enable_flash_nvidia_common(dev, name)) + return ERROR_NONFATAL; + else return 0; - rpci_write_byte(dev, 0x6d, new); - - if (pci_read_byte(dev, 0x6d) != new) { - msg_pinfo("Setting register 0x%x to 0x%x on %s failed " - "(WARNING ONLY).\n", 0x6d, new, name); - return -1; - } - - return 0; } static int enable_flash_osb4(struct pci_dev *dev, const char *name) @@ -1071,7 +1076,7 @@ static int enable_flash_mcp55(struct pci_dev *dev, const char *name) { - uint8_t old, new, val; + uint8_t val; uint16_t wordval; /* Set the 0-16 MB enable bits. */ @@ -1085,19 +1090,10 @@ wordval |= 0x7fff; /* 16M */ rpci_write_word(dev, 0x90, wordval); - old = pci_read_byte(dev, 0x6d); - new = old | 0x01; - if (new == old) + if (enable_flash_nvidia_common(dev, name)) + return ERROR_NONFATAL; + else return 0; - rpci_write_byte(dev, 0x6d, new); - - if (pci_read_byte(dev, 0x6d) != new) { - msg_pinfo("Setting register 0x%x to 0x%x on %s failed " - "(WARNING ONLY).\n", 0x6d, new, name); - return -1; - } - - return 0; } /*

1 0

[PATCH 3/3] Cleanup ft2322.c
by Stefan Tauner Sept. 4, 2012

Sept. 4, 2012

Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- ft2232_spi.c | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-) diff --git a/ft2232_spi.c b/ft2232_spi.c index 43a95e9..625dd06 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -64,8 +64,7 @@ const struct usbdev_status devs_ft2232spi[] = { {FTDI_VID, TIAO_TUMPA_PID, OK, "TIAO", "USB Multi-Protocol Adapter"}, {FTDI_VID, AMONTEC_JTAGKEY_PID, OK, "Amontec", "JTAGkey"}, {GOEPEL_VID, GOEPEL_PICOTAP_PID, OK, "GOEPEL", "PicoTAP"}, - {FIC_VID, OPENMOKO_DBGBOARD_PID, OK, "FIC", - "OpenMoko Neo1973 Debug board (V2+)"}, + {FIC_VID, OPENMOKO_DBGBOARD_PID, OK, "FIC", "OpenMoko Neo1973 Debug board (V2+)"}, {OLIMEX_VID, OLIMEX_ARM_OCD_PID, NT, "Olimex", "ARM-USB-OCD"}, {OLIMEX_VID, OLIMEX_ARM_TINY_PID, OK, "Olimex", "ARM-USB-TINY"}, {OLIMEX_VID, OLIMEX_ARM_OCD_H_PID, NT, "Olimex", "ARM-USB-OCD-H"}, @@ -74,7 +73,6 @@ const struct usbdev_status devs_ft2232spi[] = { {0}, }; - #define DEFAULT_DIVISOR 2 #define BITMODE_BITBANG_NORMAL 1 @@ -251,6 +249,7 @@ int ft2232_spi_init(void) } } free(arg); + arg = extract_programmer_param("port"); if (arg) { switch (toupper((unsigned char)*arg)) { @@ -298,6 +297,7 @@ int ft2232_spi_init(void) } } free(arg); + msg_pdbg("Using device type %s %s ", get_ft2232_vendorname(ft2232_vid, ft2232_type), get_ft2232_devicename(ft2232_vid, ft2232_type)); @@ -318,14 +318,12 @@ int ft2232_spi_init(void) f = ftdi_usb_open(ftdic, ft2232_vid, ft2232_type); if (f < 0 && f != -5) { - msg_perr("Unable to open FTDI device: %d (%s)\n", f, - ftdi_get_error_string(ftdic)); + msg_perr("Unable to open FTDI device: %d (%s)\n", f, ftdi_get_error_string(ftdic)); return -4; } if (ftdic->type != TYPE_2232H && ftdic->type != TYPE_4232H && ftdic->type != TYPE_232H) { - msg_pdbg("FTDI chip type %d is not high-speed\n", - ftdic->type); + msg_pdbg("FTDI chip type %d is not high-speed\n", ftdic->type); clock_5x = 0; } @@ -386,8 +384,6 @@ int ft2232_spi_init(void) goto ftdi_err; } - // msg_pdbg("\nft2232 chosen\n"); - register_spi_programmer(&spi_programmer_ft2232); return 0; -- Kind regards, Stefan Tauner

1 0

[PATCH 2/3] Add support for FT232H.
by Stefan Tauner Sept. 4, 2012

Sept. 4, 2012

For older versions of libftdi we define TYPE_232H ourselves and this seems to be enough to get at least basic support. Signed-off-by: Ilya A. Volynets-Evenbakh <ilya(a)total-knowledge.com> Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- Makefile | 12 ++++++++++++ flashrom.8 | 6 +++--- ft2232_spi.c | 13 ++++++++++++- 3 files changed, 27 insertions(+), 4 deletions(-) diff --git a/Makefile b/Makefile index 9309ce5..b992c5e 100644 --- a/Makefile +++ b/Makefile @@ -463,6 +463,7 @@ ifeq ($(CONFIG_FT2232_SPI), yes) FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || printf "%s" "-lftdi -lusb") # This is a totally ugly hack. FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "-D'CONFIG_FT2232_SPI=1'") +FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") PROGRAMMER_OBJS += ft2232_spi.o endif @@ -717,6 +718,12 @@ int main(int argc, char **argv) endef export FTDI_TEST +define FTDI_232H_TEST +#include <ftdi.h> +enum ftdi_chip_type type = TYPE_232H; +endef +export FTDI_232H_TEST + define UTSNAME_TEST #include <sys/utsname.h> struct utsname osinfo; @@ -751,6 +758,11 @@ ifeq ($(CONFIG_FT2232_SPI), yes) @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ ( echo "found."; echo "FTDISUPPORT := yes" >> .features.tmp ) || \ ( echo "not found."; echo "FTDISUPPORT := no" >> .features.tmp ) + @printf "Checking for FT232H support in libftdi... " + @echo "$$FTDI_232H_TEST" >> .featuretest.c + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ + ( echo "found."; echo "FT232H := yes" >> .features.tmp ) || \ + ( echo "not found."; echo "FT232H := no" >> .features.tmp ) endif ifeq ($(CONFIG_LINUX_SPI), yes) @printf "Checking if Linux SPI headers are present... " diff --git a/flashrom.8 b/flashrom.8 index 1699f2a..19506a3 100644 --- a/flashrom.8 +++ b/flashrom.8 @@ -15,7 +15,7 @@ chips. It's often used to flash BIOS/EFI/coreboot/firmware images in-system using a supported mainboard. However, it also supports various external PCI/USB/parallel-port/serial-port based devices which can program flash chips, including some network cards (NICs), SATA/IDE controller cards, graphics cards, -the Bus Pirate device, various FTDI FT2232/FT4232H based USB devices, and more. +the Bus Pirate device, various FTDI FT2232/FT4232H/FT232H based USB devices, and more. .PP It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, TSOP40, TSOP48, and BGA chips, which use various protocols such as LPC, FWH, @@ -189,7 +189,7 @@ cards)" .sp .BR "* atahpt" " (for flash ROMs on Highpoint ATA/RAID controllers)" .sp -.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H family \ +.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family \ based USB SPI programmer), including the DLP Design DLP-USB1232H, \ FTDI FT2232H Mini-Module, FTDI FT4232H Mini-Module, openbiosprog-spi, Amontec \ JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, \ @@ -561,7 +561,7 @@ type and channel/interface/port it should support. For that you have to use the syntax where .B model can be -.BR 2232H ", " 4232H ", " jtagkey ", " busblaster ", " openmoko ", " \ +.BR 2232H ", " 4232H ", " 232H ", " jtagkey ", " busblaster ", " openmoko ", " \ arm-usb-tiny ", " arm-usb-tiny-h ", " arm-usb-ocd ", " arm-usb-ocd-h \ ", " tumpa ", or " picotap and diff --git a/ft2232_spi.c b/ft2232_spi.c index 0e18a0c..43a95e9 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -30,11 +30,18 @@ #include "spi.h" #include <ftdi.h> +/* This is not defined in libftdi.h <0.20 (c7e4c09e68cfa6f5e112334aa1b3bb23401c8dc7 to be exact). + * Some tests indicate that his is the only change that it is needed to support the FT232H in flashrom. */ +#if !defined(HAVE_FT232H) +#define TYPE_232H 6 +#endif + /* Please keep sorted by vendor ID, then device ID. */ #define FTDI_VID 0x0403 #define FTDI_FT2232H_PID 0x6010 #define FTDI_FT4232H_PID 0x6011 +#define FTDI_FT232H_PID 0x6014 #define TIAO_TUMPA_PID 0x8a98 #define AMONTEC_JTAGKEY_PID 0xCFF8 @@ -53,6 +60,7 @@ const struct usbdev_status devs_ft2232spi[] = { {FTDI_VID, FTDI_FT2232H_PID, OK, "FTDI", "FT2232H"}, {FTDI_VID, FTDI_FT4232H_PID, OK, "FTDI", "FT4232H"}, + {FTDI_VID, FTDI_FT232H_PID, OK, "FTDI", "FT232H"}, {FTDI_VID, TIAO_TUMPA_PID, OK, "TIAO", "USB Multi-Protocol Adapter"}, {FTDI_VID, AMONTEC_JTAGKEY_PID, OK, "Amontec", "JTAGkey"}, {GOEPEL_VID, GOEPEL_PICOTAP_PID, OK, "GOEPEL", "PicoTAP"}, @@ -190,6 +198,9 @@ int ft2232_spi_init(void) } else if (!strcasecmp(arg, "4232H")) { ft2232_type = FTDI_FT4232H_PID; channel_count = 4; + } else if (!strcasecmp(arg, "232H")) { + ft2232_type = FTDI_FT232H_PID; + channel_count = 1; } else if (!strcasecmp(arg, "jtagkey")) { ft2232_type = AMONTEC_JTAGKEY_PID; channel_count = 2; @@ -312,7 +323,7 @@ int ft2232_spi_init(void) return -4; } - if (ftdic->type != TYPE_2232H && ftdic->type != TYPE_4232H) { + if (ftdic->type != TYPE_2232H && ftdic->type != TYPE_4232H && ftdic->type != TYPE_232H) { msg_pdbg("FTDI chip type %d is not high-speed\n", ftdic->type); clock_5x = 0; -- Kind regards, Stefan Tauner

1 0

[PATCH 1/3] Add support for all 4 possible channels to the ft2232_spi programmer.
by Stefan Tauner Sept. 4, 2012

Sept. 4, 2012

Add a check to validate the selected channel/interface, which not even libftdi seems to do yet. This patch changes default behavior: the new default channel/interface is A. Also, this patch uses the word 'channel' in addition or in place of 'interface' where possible without too much hassle because it is the term FTDI uses. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- flashrom.8 | 6 +++--- ft2232_spi.c | 59 +++++++++++++++++++++++++++++++++++++++------------------- 2 files changed, 43 insertions(+), 22 deletions(-) diff --git a/flashrom.8 b/flashrom.8 index bf671c2..1699f2a 100644 --- a/flashrom.8 +++ b/flashrom.8 @@ -554,7 +554,7 @@ Example: .SS .BR "ft2232_spi " programmer An optional parameter specifies the controller -type and interface/port it should support. For that you have to use the +type and channel/interface/port it should support. For that you have to use the .sp .B " flashrom \-p ft2232_spi:type=model,port=interface" .sp @@ -567,11 +567,11 @@ arm-usb-tiny ", " arm-usb-tiny-h ", " arm-usb-ocd ", " arm-usb-ocd-h \ and .B interface can be -.BR A ", or " B . +.BR A ", " B ", " C ", or " D . The default model is .B 4232H and the default interface is -.BR B . +.BR A . .sp All models supported by the ft2232_spi driver can configure the SPI clock rate by setting a divisor. The expressible divisors are all even numbers between 2 and 2^17 (=131072) resulting in SPI clock frequencies of diff --git a/ft2232_spi.c b/ft2232_spi.c index edea1e6..0e18a0c 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -161,7 +161,8 @@ int ft2232_spi_init(void) unsigned char buf[512]; int ft2232_vid = FTDI_VID; int ft2232_type = FTDI_FT4232H_PID; - enum ftdi_interface ft2232_interface = INTERFACE_B; + int channel_count = 4; /* Stores the number of channels of the device. */ + enum ftdi_interface ft2232_interface = INTERFACE_A; /* * The 'H' chips can run with an internal clock of either 12 MHz or 60 MHz, * but the non-H chips can only run at 12 MHz. We enable the divide-by-5 @@ -183,53 +184,55 @@ int ft2232_spi_init(void) arg = extract_programmer_param("type"); if (arg) { - if (!strcasecmp(arg, "2232H")) + if (!strcasecmp(arg, "2232H")) { ft2232_type = FTDI_FT2232H_PID; - else if (!strcasecmp(arg, "4232H")) + channel_count = 2; + } else if (!strcasecmp(arg, "4232H")) { ft2232_type = FTDI_FT4232H_PID; - else if (!strcasecmp(arg, "jtagkey")) { + channel_count = 4; + } else if (!strcasecmp(arg, "jtagkey")) { ft2232_type = AMONTEC_JTAGKEY_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; cs_bits = 0x18; pindir = 0x1b; } else if (!strcasecmp(arg, "picotap")) { ft2232_vid = GOEPEL_VID; ft2232_type = GOEPEL_PICOTAP_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; } else if (!strcasecmp(arg, "tumpa")) { /* Interface A is SPI1, B is SPI2. */ ft2232_type = TIAO_TUMPA_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; } else if (!strcasecmp(arg, "busblaster")) { /* In its default configuration it is a jtagkey clone */ ft2232_type = FTDI_FT2232H_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; cs_bits = 0x18; pindir = 0x1b; } else if (!strcasecmp(arg, "openmoko")) { ft2232_vid = FIC_VID; ft2232_type = OPENMOKO_DBGBOARD_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; } else if (!strcasecmp(arg, "arm-usb-ocd")) { ft2232_vid = OLIMEX_VID; ft2232_type = OLIMEX_ARM_OCD_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; cs_bits = 0x08; pindir = 0x1b; } else if (!strcasecmp(arg, "arm-usb-tiny")) { ft2232_vid = OLIMEX_VID; ft2232_type = OLIMEX_ARM_TINY_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; } else if (!strcasecmp(arg, "arm-usb-ocd-h")) { ft2232_vid = OLIMEX_VID; ft2232_type = OLIMEX_ARM_OCD_H_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; cs_bits = 0x08; pindir = 0x1b; } else if (!strcasecmp(arg, "arm-usb-tiny-h")) { ft2232_vid = OLIMEX_VID; ft2232_type = OLIMEX_ARM_TINY_H_PID; - ft2232_interface = INTERFACE_A; + channel_count = 2; } else { msg_perr("Error: Invalid device type specified.\n"); free(arg); @@ -245,14 +248,30 @@ int ft2232_spi_init(void) break; case 'B': ft2232_interface = INTERFACE_B; + if (channel_count < 2) + channel_count = -1; + break; + case 'C': + ft2232_interface = INTERFACE_C; + if (channel_count < 3) + channel_count = -1; + break; + case 'D': + ft2232_interface = INTERFACE_D; + if (channel_count < 4) + channel_count = -1; break; default: - msg_perr("Error: Invalid port/interface specified.\n"); - free(arg); - return -2; + channel_count = -1; + break; } } free(arg); + if (channel_count < 0) { + msg_perr("Error: Invalid channel/port/interface specified.\n"); + return -2; + } + arg = extract_programmer_param("divisor"); if (arg && strlen(arg)) { unsigned int temp = 0; @@ -271,8 +290,10 @@ int ft2232_spi_init(void) msg_pdbg("Using device type %s %s ", get_ft2232_vendorname(ft2232_vid, ft2232_type), get_ft2232_devicename(ft2232_vid, ft2232_type)); - msg_pdbg("interface %s\n", - (ft2232_interface == INTERFACE_A) ? "A" : "B"); + msg_pdbg("channel %s\n", + (ft2232_interface == INTERFACE_A) ? "A" : + (ft2232_interface == INTERFACE_B) ? "B" : + (ft2232_interface == INTERFACE_C) ? "C" : "D"); if (ftdi_init(ftdic) < 0) { msg_perr("ftdi_init failed\n"); @@ -280,7 +301,7 @@ int ft2232_spi_init(void) } if (ftdi_set_interface(ftdic, ft2232_interface) < 0) { - msg_perr("Unable to select interface: %s\n", ftdic->error_str); + msg_perr("Unable to select channel: %s\n", ftdic->error_str); } f = ftdi_usb_open(ftdic, ft2232_vid, ft2232_type); -- Kind regards, Stefan Tauner

1 0

[PATCH 1/2] libftdi complains that it is impossible to set interface on an already open device.
by Ilya A. Volynets-Evenbakh Sept. 4, 2012

Sept. 4, 2012

Call to ftdi_set_interface right after ftdi_init and before call to ftdi_usb_open Signed-off-by: Ilya A. Volynets-Evenbakh <ilya(a)total-knowledge.com> --- ft2232_spi.c | 10 +++++----- 1 files changed, 5 insertions(+), 5 deletions(-) diff --git a/ft2232_spi.c b/ft2232_spi.c index aec2fd5..aaca5f3 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -276,6 +276,11 @@ int ft2232_spi_init(void) return -3; } + if (ftdi_set_interface(ftdic, ft2232_interface) < 0) { + msg_perr("Unable to select interface: %s\n", + ftdic->error_str); + } + f = ftdi_usb_open(ftdic, ft2232_vid, ft2232_type); if (f < 0 && f != -5) { @@ -290,11 +295,6 @@ int ft2232_spi_init(void) clock_5x = 0; } - if (ftdi_set_interface(ftdic, ft2232_interface) < 0) { - msg_perr("Unable to select interface: %s\n", - ftdic->error_str); - } - if (ftdi_usb_reset(ftdic) < 0) { msg_perr("Unable to reset FTDI device\n"); } -- 1.7.3.4

2 4

Flashing Jetway J7F4K9G2 bios
by Edwin Wijburg Sept. 3, 2012

Sept. 3, 2012

Yesterday I contacted you via IRC because of a possible flash failure on my Jetway J7F4K9G2 motherboard. Luckily the error was not severe as a --verify confirmed an intact bios (thanks again for the online help!). I used an old flashrom version from the Debian squeeze repositories and was advised to upgrade to at least the version in testing. I compiled from source. What I am trying (off course) is to ascertain if my bios can be flashed with flashrom. I do have the latest bios for this board but it was cumbersome to make a flash usb stick with freedos, fiddle with the bios settings to get my board to boot the stick, well, you know ....... (why else flashrom?) Your wiki-list shows one Jetway family member that works with flashrom (the J7F4K1G5D-PB). I'd like to be able to tell you mine works with it as well (so it can be added to the list). Now, when I probe the motherboard flashrom tells me that it has two flashchips (the old flashrom didn't do that). Which one is the one to use? I've included the flashrom's output for the probe and read actions on the respective chips. The motherboard has in fact two NIC biosses as well. But I didn't compile with external programmers so I imagine the probe then should not find those? In the wiki you clearly state that testing an erase and write should only be done when I have an alternative bios chip at hand. And I don't. Should I stop the experimenting alltogether or are there other ways to find out if chances are good that my board will be flashable? Edwin.

2 1

Re: [flashrom] About mcp73 support on flashrom
by Stefan Tauner Sept. 3, 2012

Sept. 3, 2012

On Thu, 22 Mar 2012 13:53:34 +0200 Olcay Korkmaz <olcay.mz(a)gmail.com> wrote: > Hello all > I have Zotac 630i-itx board (old pcb rev model..very old i guess) > flashrom -V log details on mail attachment > is it safe to erase/write process > extra info bios dump is ok via flashrom -r command > Hello Olcay! seems to work fine: http://www.flashrom.org/pipermail/flashrom/2012-April/009073.html -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

[patch] atavia
by Idwer Vollering Sept. 2, 2012

Sept. 2, 2012

Add VIA VT6421A LPC programmer driver. Updated to be applied against HEAD (r1357 --> r1586). Signed-off-by: Jonathan Kollasch <jakllsch(a)kollasch.net>

1 0

Re: [flashrom] [PATCH] Fix compilation with MinGW.
by Stefan Tauner Sept. 1, 2012

Sept. 1, 2012

On Sat, 1 Sep 2012 23:40:57 +0200 Idwer Vollering <vidwer(a)gmail.com> wrote: > 2012/9/1 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at>: > > This was broken since r1557 when we got rid of some exit calls, but returned > > -1 instead which is not a valid HANDLE value. > > > > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > > Acked-by: Idwer Vollering <vidwer(a)gmail.com> thanks, committed in r1591 -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0