February 2012 - flashrom - mail.coreboot.org

Some specs for IT8518 buried in my laptops ESM
by Eric Appleman Feb. 28, 2012

Feb. 28, 2012

http://www.mediafire.com/?t77ue8xx1cv49g9 Page 87 has a full blown schematic. Enjoy. - Eric

1 0

[PATCH] FT2232 programmer frequency divider parameter support
by Samir Ibradžić Feb. 28, 2012

Feb. 28, 2012

Hello, I would like to submit a patch, that enables extra argument when using FT2232 external programmer, a frequency divider. For FT2232 programmer we have this divider set to 3 by default by DIVIDE_BY constant, which will result in 10MHz (H-chips) or 2MHz (non H-chips) SPI speeds. By providing divider as parameter, SPI interface frequency culd be overridden by user, resulting in different speeds (H-chip example): divider | freq ---------+-------- 1 | 30Mhz 2 | 15Mhz 3 | 10Mhz 4 | 7.5Mhz 5 | 6Mhz 6 | 5Mhz 15 | 2Mhz 30 | 1Mhz 60 | 0.5Mhz 600 | 0.05Mhz (and so on) These lower than default SPI speeds can be very useful when we have flawed flash chips that would not support 10Mhz or bad quality or too long cabling between programmer and the chip. Higher than default speeds might also be useful (if only flashrom AAI implementation was faster). Please note that this parameter is arbitrary integer, maybe only a value up to 255 would really make sense, but i can not be sure about that since it may be programmer hardware dependent. All values between 1-255 worked for me (PicoTAP programmer), as well as 300 & 600 (these resulted in extremely slow flash reads, as expected, 2MB flash that usually takes 16s to read @2-10Mhz, took more than 6 minutes @0.05Mhz). Others values i haven't tested. Signed-off-by: Samir Ibradžić <sibradzic(a)gmail.com> --- $ svn diff Index: ft2232_spi.c =================================================================== --- ft2232_spi.c (revision 1451) +++ ft2232_spi.c (working copy) @@ -168,6 +168,7 @@ enum ftdi_interface ft2232_interface = INTERFACE_B; char *arg; double mpsse_clk; + int divider = DIVIDE_BY; arg = extract_programmer_param("type"); if (arg) { @@ -237,6 +238,17 @@ } } free(arg); + arg = extract_programmer_param("divider"); + if (arg) { + if (isdigit(*arg) && (atoi(arg) > 0)) + divider = atoi(arg); + else { + msg_perr("Error: Invalid frequency divider specified.\n"); + free(arg); + return -2; + } + } + free(arg); msg_pdbg("Using device type %s %s ", get_ft2232_vendorname(ft2232_vid, ft2232_type), get_ft2232_devicename(ft2232_vid, ft2232_type)); @@ -298,16 +310,16 @@ msg_pdbg("Set clock divisor\n"); buf[0] = 0x86; /* command "set divisor" */ /* valueL/valueH are (desired_divisor - 1) */ - buf[1] = (DIVIDE_BY - 1) & 0xff; - buf[2] = ((DIVIDE_BY - 1) >> 8) & 0xff; + buf[1] = (divider - 1) & 0xff; + buf[2] = ((divider - 1) >> 8) & 0xff; if (send_buf(ftdic, buf, 3)) { ret = -6; goto ftdi_err; } msg_pdbg("MPSSE clock: %f MHz divisor: %d " - "SPI clock: %f MHz\n", mpsse_clk, DIVIDE_BY, - (double)(mpsse_clk / (((DIVIDE_BY - 1) + 1) * 2))); + "SPI clock: %f MHz\n", mpsse_clk, divider, + (double)(mpsse_clk / (((divider - 1) + 1) * 2))); /* Disconnect TDI/DO to TDO/DI for loopback. */ msg_pdbg("No loopback of TDI/DO TDO/DI\n"); -- R, S

2 2

Re: [flashrom] Test report Biostar M7VIQ - Chip not detected
by Carl-Daniel Hailfinger Feb. 27, 2012

Feb. 27, 2012

Hi Gurken, Am 26.02.2012 22:46 schrieb Gurken Papst: > Winbond W49F002U flash chip is not detected on a Biostar M7VIQ. > Detection and reading flash works using UniFlash 1.40. Writing > untested. > > Output of flashrom -V: > flashrom v0.9.5-r1503 on Linux 2.6.39.3 (i686), built with libpci > 3.1.8, GCC 4.6.2, little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 832M loops > per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1007 us, > 10000 myus = 10169 us, 4 myus = 4 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: " " > DMI string system-product-name: " " > DMI string system-version: " " > DMI string baseboard-manufacturer: " " > DMI string baseboard-product-name: "KM266-8235" > DMI string baseboard-version: " " > DMI string chassis-type: "Desktop" > Found chipset "VIA VT8235" with PCI ID 1106:3177. Enabling flash write... OK. > The following protocols are supported: Non-SPI. > Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xd6, id2 > 0x52, id1 is normal flash content, id2 is normal flash content > [...] > > superiotool -dV: > [...] > Found Winbond W83697HF/F/HG (id=0x60, rev=0x12) at 0x2e > Register dump: > idx 20 21 22 23 24 25 26 28 29 2a > val 60 12 ff fe 10 00 00 00 00 f0 > def 60 NA ff 00 00 00 00 00 00 MM Register 0x24 says ROM size is 2 Mbit. Register 0x2a says flash translation is enabled. We should autodetect this Super I/O and set bit 3 in register 0x24 to enable detection and writing. > LDN 0x00 (Floppy) > idx 30 60 61 70 74 f0 f1 f2 f4 f5 > val 01 03 f0 06 02 0e 00 ff 00 00 > def 01 03 f0 06 02 0e 00 ff 00 00 We have a patch for this somewhere, but it is probably pretty bitrotted and needs to be updated. Would you be willing to test a few patches? Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

Re: [flashrom] [PATCH 7/8] check if write enable is really set in nicintel_spi_init (and minor comment changes).
by Stefan Tauner Feb. 27, 2012

Feb. 27, 2012

On Mon, 20 Feb 2012 19:49:06 +0100 Idwer Vollering <vidwer(a)gmail.com> wrote: > 2011/3/15 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at>: > > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > > Adding "pci_mmio_writel(FLASH_WRITES_DISABLED, nicintel_spibar + > EECD);" right after the usage of register_shutdown() works as it > should: > > Initializing nicintel_spi programmer > Found "Intel 82541PI Gigabit Ethernet Controller" (8086:107c, BDF 01:01.0). > Requested BAR is MEM, 32bit, not prefetchable > Enabling flash write access failed. > Error: Programmer initialization failed. > > Acked-by: Idwer Vollering <vidwer(a)gmail.com> thanks! committed in r1510 -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[commit] r1510 - trunk
by repository service Feb. 27, 2012

Feb. 27, 2012

Author: stefanct Date: Mon Feb 27 20:44:16 2012 New Revision: 1510 URL: http://flashrom.org/trac/flashrom/changeset/1510 Log: nicintel_spi.c: check if write enable is really set (and minor comment changes). Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Idwer Vollering <vidwer(a)gmail.com> Modified: trunk/nicintel_spi.c Modified: trunk/nicintel_spi.c ============================================================================== --- trunk/nicintel_spi.c Sun Feb 26 00:40:16 2012 (r1509) +++ trunk/nicintel_spi.c Mon Feb 27 20:44:16 2012 (r1510) @@ -31,12 +31,15 @@ #define PCI_VENDOR_ID_INTEL 0x8086 +/* EEPROM/Flash Control & Data Register */ #define EECD 0x10 +/* Flash Access Register */ #define FLA 0x1c /* * Register bits of EECD. - * + * Table 13-6 + * * Bit 04, 05: FWE (Flash Write Enable Control) * 00b = not allowed * 01b = flash writes disabled @@ -46,8 +49,9 @@ #define FLASH_WRITES_DISABLED 0x10 /* FWE: 10000b */ #define FLASH_WRITES_ENABLED 0x20 /* FWE: 100000b */ -/* Flash Access register bits */ -/* Table 13-9 */ +/* Flash Access register bits + * Table 13-9 + */ #define FL_SCK 0 #define FL_CS 1 #define FL_SI 2 @@ -179,6 +183,13 @@ tmp |= FLASH_WRITES_ENABLED; pci_mmio_writel(tmp, nicintel_spibar + EECD); + /* test if FWE is really set to allow writes */ + tmp = pci_mmio_readl(nicintel_spibar + EECD); + if ( (tmp & FLASH_WRITES_DISABLED) || !(tmp & FLASH_WRITES_ENABLED) ) { + msg_perr("Enabling flash write access failed.\n"); + return 1; + } + if (register_shutdown(nicintel_spi_shutdown, NULL)) return 1;

1 0

Re: [flashrom] flashrom with HP XW9300
by Carl-Daniel Hailfinger Feb. 27, 2012

Feb. 27, 2012

Hi Jürgen, I remember a similar case where flashrom was unable to write, and that board also had a second chipset match. We might have the same issue here: To PCI devices with the same ID, one acts as southbridge and the other one is unused. We might enable the wrong one here and might have to refine detection a bit. OTOH, a flash chip is detected, so we know that write was enabled on the address space mapped to the flash chip (but that write enable might have not been done by flashrom). Am 26.02.2012 20:38 schrieb Jürgen Trapp: > ubuntu@ubuntu:~/coreboot$ sudo flashrom -VV > flashrom v0.9.5.1-r1508 on Linux 3.0.0-12-generic (i686), built with libpci 3.1.7, GCC 4.6.1, little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 4001 usecs, 1093M loops per second, 10 myus = 0 us, 100 myus = 0 us, 1000 myus = 0 us, 10000 myus = 8001 us, 16004 myus = 16001 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "Hewlett-Packard" > DMI string system-product-name: "HP xw9300 Workstation" > DMI string system-version: " " > DMI string baseboard-manufacturer: "Hewlett-Packard" > DMI string baseboard-product-name: "09C4h" > DMI string baseboard-version: "Not Specified" > DMI string chassis-type: "Mini Tower" > Found chipset "NVIDIA CK804" with PCI ID 10de:0051. Enabling flash write... OK. > WARNING: unexpected second chipset match: "NVIDIA CK804" Side note: We should print the PCI ID for the second chipset match as well. > ignoring, please report lspci and board URL to flashrom(a)flashrom.org > with 'CHIPSET: your board name' in the subject line. > The following protocols are supported: Non-SPI. > Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0x65, id2 0xd0, id1 parity violation, id1 is normal flash content, id2 is normal flash content > [...] Could you run the following command as root and post the results? lspci -nnvvxxx That should help us determine which one of the CK804 southbridges we should enable. However, it is possible that we enabled the right southbridge due to pure luck and there is a separate write protection (jumper or solder bridge or something controllable in software). If that is the case, somebody has to find out how to enable writes by reverse engineering or by looking at the docs if the docs are good. Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

send log from ASUS P8H61 PRO bios ver 0605
by Pavel Petrov Feb. 27, 2012

Feb. 27, 2012

flashrom -r 1 -V flashrom v0.9.5.1-r1508 on Linux 3.0.0-16-generic-pae (i686), built with libpci 3.1.8, GCC 4.6.2, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 3585M loops per second, 10 myus = 10 us, 100 myus = 114 us, 1000 myus = 1013 us, 10000 myus = 10252 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "P8H61 PRO" DMI string baseboard-version: "Rev X.0x" DMI string chassis-type: "Desktop" Found chipset "Intel H61" with PCI ID 8086:1c5c. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0xc24: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00001000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write. 0x5C: 0x017f0001 FREG2: WARNING: Management Engine region (0x00001000-0x0017ffff) is locked. Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00002005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) SPI Read Configuration: prefetching disabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Chip status register is 00 Found Winbond flash chip "W25Q32" (4096 kB, SPI) at physical address 0xffc00000. Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 ID of the mandatory JEDEC SFDP parameter table is not 0 as demanded by JESD216 (warning only). Parsing JEDEC flash parameter table... It seems like this chip supports the preliminary Intel version of SFDP, skipping processing of double words 3-9. done. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xef, id2 0x15 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x6f, id2 0xa7, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xa0, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xa0, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x28, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q32" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0xb776c8a0 Restoring MMIO space at 0xb776c89c Restoring MMIO space at 0xb776c898 Restoring MMIO space at 0xb776c896 Restoring MMIO space at 0xb776c894 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

Test report Biostar M7VIQ - Chip not detected
by Gurken Papst Feb. 26, 2012

Feb. 26, 2012

Winbond W49F002U flash chip is not detected on a Biostar M7VIQ. Detection and reading flash works using UniFlash 1.40. Writing untested. Output of flashrom -V: flashrom v0.9.5-r1503 on Linux 2.6.39.3 (i686), built with libpci 3.1.8, GCC 4.6.2, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 832M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1007 us, 10000 myus = 10169 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "KM266-8235" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "VIA VT8235" with PCI ID 1106:3177. Enabling flash write... OK. The following protocols are supported: Non-SPI. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0xd6, id2 0x52, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x25, id2 0x5a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. Restoring PCI config space for 00:11:0 reg 0x40 Restoring PCI config space for 00:11:0 reg 0x41 Output of lspci -nnvvxxx: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8375 [KM266/KL266] Host Bridge [1106:3116] Subsystem: VIA Technologies, Inc. VT8375 [KM266/KL266] Host Bridge [1106:3116] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 8 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: agpgart-via 00: 06 11 16 31 06 00 30 22 00 00 00 06 00 08 00 00 10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 16 31 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 40: 00 18 88 80 82 44 00 20 18 99 88 80 82 44 00 00 50: e0 00 00 02 c0 04 50 50 ee 00 20 40 50 50 50 50 60: 0a 2a 00 20 e6 99 02 2e de 0d 43 50 c4 05 00 00 70: 82 c8 00 01 01 01 10 00 01 00 00 00 00 00 02 12 80: 0f 61 00 00 c0 00 00 00 03 00 cd 35 00 00 00 00 90: 17 a3 6b ea 4f 1c 08 19 11 33 00 00 61 11 01 00 a0: 02 c0 20 00 07 02 00 1f 04 01 00 00 2f 02 04 00 b0: 78 ac 18 9b 80 00 00 00 88 00 00 00 00 00 20 00 c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 1a 00 00 01 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 01 13 00 00 00 00 00 00 00 00 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] [1106:b091] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: ec000000-edffffff Prefetchable memory behind bridge: e0000000-e7ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 91 b0 07 01 30 22 00 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: 00 ec f0 ed 00 e0 f0 e7 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00 40: 81 c0 00 44 24 72 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 02 02 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at d000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00: 06 11 38 30 07 00 10 02 80 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d0 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 01 00 00 40: 40 10 07 00 00 00 00 00 00 0b 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at d400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00: 06 11 38 30 07 00 10 02 80 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d4 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 02 00 00 40: 40 10 07 00 00 00 00 00 00 0b 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 21 Region 4: I/O ports at d800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00: 06 11 38 30 07 00 10 02 80 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d8 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 03 00 00 40: 40 10 03 00 00 00 00 00 00 0b 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 21 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: 06 11 04 31 17 00 10 02 82 20 03 0c 08 20 00 00 10: 00 00 00 ee 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31 30: 00 00 00 00 80 00 00 00 00 00 00 00 03 04 00 00 40: 00 00 03 00 00 00 00 00 a0 10 00 09 00 00 00 00 50: 00 5a 00 80 00 00 00 00 04 0b 88 88 53 88 00 00 60: 20 20 01 00 00 00 00 00 01 00 00 00 00 00 08 c0 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177] Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 77 31 87 00 10 02 00 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 77 31 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 40: 54 7f f8 0b 00 00 00 00 0c 20 00 00 04 00 0a 08 50: 81 1d 09 00 00 20 22 20 43 00 00 00 00 00 00 00 60: 00 00 f0 40 00 00 08 04 00 00 00 00 00 00 00 00 70: 06 11 77 31 00 00 00 00 00 00 00 00 20 00 00 00 80: 20 84 59 00 fa 10 00 00 01 40 00 00 da 00 00 00 90: 00 1f f9 88 a4 40 00 00 00 be 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 50 01 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 08 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 05 00 00 00 00 00 00 00 00 00 00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 20 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at dc00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_via 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 dc 00 00 00 00 00 00 00 00 00 00 06 11 71 05 30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 01 00 00 40: 0b f2 09 05 18 1c c0 00 20 20 99 99 ff 00 20 a8 50: e6 e6 17 17 0c 03 00 00 a8 a8 a8 a8 00 00 00 00 60: 00 02 00 00 00 00 00 00 00 02 00 00 00 00 00 00 70: 02 01 00 00 00 00 00 00 02 01 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 d0 dd 35 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 06 00 71 05 06 11 71 05 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 07 00 00 00 00 00 00 00 00 00 00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50) Subsystem: VIA Technologies, Inc. K7VT2 motherboard [1106:4161] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 22 Region 0: I/O ports at e000 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: VIA 82xx Audio 00: 06 11 59 30 01 00 10 02 50 00 01 04 00 00 00 00 10: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 61 41 30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 03 00 00 40: 01 cc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 01 00 02 06 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 00 02 06 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 74) Subsystem: Biostar Microtech Int'l Corp Device [1565:2200] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at e800 [size=256] Region 1: Memory at ee001000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: via-rhine 00: 06 11 65 30 07 00 10 02 74 00 00 02 08 20 00 00 10: 01 e8 00 00 00 10 00 ee 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 65 15 00 22 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 03 08 40: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01:00.0 VGA compatible controller [0300]: nVidia Corporation NV11 [GeForce2 MX/MX 400] [10de:0110] (rev a1) (prog-if 00 [VGA controller]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M] [virtual] Expansion ROM at ed000000 [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4 Kernel driver in use: nouveau 00: de 10 10 01 07 00 b0 02 a1 00 00 03 00 20 00 00 10: 00 00 00 ec 08 00 00 e0 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 05 01 40: 00 00 00 00 02 00 20 00 17 00 00 1f 04 01 00 1f 50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00 60: 01 44 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Output of superiotool -deV: superiotool r5050 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x10fe, id=0x1260 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x6012, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83697HF/F/HG (id=0x60, rev=0x12) at 0x2e Register dump: idx 20 21 22 23 24 25 26 28 29 2a val 60 12 ff fe 10 00 00 00 00 f0 def 60 NA ff 00 00 00 00 00 00 MM LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 01 03 f0 06 02 0e 00 ff 00 00 def 01 03 f0 06 02 0e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 01 03 78 07 04 01 def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 00 00 00 00 00 def 01 02 f8 03 00 00 LDN 0x06 (Consumer IR) idx 30 60 61 70 val 00 00 00 00 def 00 00 00 00 LDN 0x07 (Game port, GPIO 1) idx 30 60 61 62 63 f0 f1 f2 val 01 02 01 00 00 ff 00 00 def 00 02 01 00 00 ff 00 00 LDN 0x08 (MIDI port, GPIO 5) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 val 01 03 30 00 00 0a ff 00 00 00 00 00 def 00 03 30 00 00 09 ff 00 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4) idx 30 60 61 f0 f1 f2 f3 f4 f5 f6 f7 f8 f5 val 00 00 00 ff ff ff ff ff ff ff ff ff ff def 00 00 00 ff 00 00 ff 00 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e5 e6 e7 f0 f1 f3 f4 f6 f7 f9 val 01 00 00 00 ff 00 00 00 00 af 06 08 00 08 05 def 00 00 00 00 NA 00 00 00 00 00 00 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 val 01 02 90 00 def 00 00 00 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for VIA Super I/O at 0x3f0... PCI device 1106:0686 not found.

1 0

flashrom with HP XW9300
by Jürgen Trapp Feb. 26, 2012

Feb. 26, 2012

Hi, i have a problem with flash writing under HP XW9300. I will use coreboot.rom with the board and i have a error (see attachments: output_flashrom_write) Thank you for help. Jürgen

1 0

Re: [flashrom] [PATCH 1/2] revert flashctx to flashchip in block_eraser helper functions
by Carl-Daniel Hailfinger Feb. 26, 2012

Feb. 26, 2012

Am 28.12.2011 01:57 schrieb Stefan Tauner: > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Sorry, Nack. Quoting from your other mail: > it is easier to "upcast" some flashctx > "objects" to flashchip (which is safe) AFAICS this violates the C standard. http://stackoverflow.com/questions/98650/what-is-the-strict-aliasing-rule The offending hunks are below: > diff --git a/flashrom.c b/flashrom.c > index f1a6165..68b6d97 100644 > --- a/flashrom.c > +++ b/flashrom.c > @@ -1313,7 +1313,7 @@ int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, > int k, ret = 1; > uint8_t *curcontents; > unsigned long size = flash->total_size * 1024; > - unsigned int usable_erasefunctions = count_usable_erasers(flash); > + unsigned int usable_erasefunctions = count_usable_erasers((struct flashchip*) flash); > > msg_cinfo("Erasing and writing flash chip... "); > curcontents = malloc(size); > @@ -1332,7 +1332,7 @@ int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, > break; > } > msg_cdbg("Trying erase function %i... ", k); > - if (check_block_eraser(flash, k, 1)) > + if (check_block_eraser((struct flashchip*) flash, k, 1)) > continue; > usable_erasefunctions--; > ret = walk_eraseregions(flash, k, &erase_and_write_block_helper, > @@ -1680,7 +1680,7 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it, > int ret = 0; > unsigned long size = flash->total_size * 1024; > > - if (chip_safety_check(flash, force, read_it, write_it, erase_it, verify_it)) { > + if (chip_safety_check((struct flashchip*) flash, force, read_it, write_it, erase_it, verify_it)) { > msg_cerr("Aborting.\n"); > ret = 1; > goto out_nofree; -- http://www.hailfinger.org/

2 1