flashrom February 2010

flashrom@flashrom.org

55 participants
173 discussions

Winbond W39V040B on ASRock 939DUAL-VSTA
by Henne 06 Feb '10

06 Feb '10

Hi there, I want to give you some feedback for the W39V040B with flashrom-r893. Probe works fine: flashrom v0.9.1-runknown No coreboot table found. This chipset supports the following protocols: Non-SPI. WARNING: No chipset found. Flash detection will most likely fail. Calibrating delay loop... OK. Found chip "Winbond W39V040B" (512 KB, LPC) at physical address 0xfff80000. Reading works fine too, but there are 7451 differences between the original file I flashed with ASRocks tool and the image I got with flashrom. Extracting both images with bios_extract results in identical files. Most of the differences are 0xff from the original and 0x00 of flashrom. Here are the dumps: Original: 0005fff0 53 43 30 38 30 30 2d 74 20 40 95 d7 0c 00 83 df |SC0800-t @......| 00060000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00070000 0c 79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |.y..............| Flashrom: 0005fff0 53 43 30 38 30 30 2d 74 20 40 95 d7 0c 00 83 df |SC0800-t @......| 00060000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 0006c000 05 00 00 00 00 08 00 00 10 00 01 ff ff ff ff ff |................| 0006c010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 0006c800 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 0006c840 00 80 01 00 40 00 40 08 10 00 01 ff ff ff ff ff |....@.@.........| 0006c850 00 13 8f c4 e7 bf 0d 00 ff ff ff ff ff ff ff ff |................| 0006c860 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 0006c880 08 00 02 00 9a 00 80 08 10 00 01 ff ff ff ff ff |................| 0006c890 f2 03 ac ce b6 00 00 00 00 00 00 00 00 00 00 00 |................| 0006c8a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 0006c8b0 00 00 03 48 48 52 52 43 43 00 00 00 00 00 00 00 |...HHRRCC.......| 0006c8c0 00 00 00 02 00 01 03 04 05 06 07 00 00 00 00 01 |................| 0006c8d0 b9 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 0006c8e0 00 00 00 00 00 00 00 00 00 01 02 03 04 05 06 07 |................| 0006c8f0 08 09 0a 0b 00 00 00 00 01 52 5c 00 00 00 00 00 |.........R\.....| 0006c900 00 00 01 03 01 00 00 00 00 01 ff d2 00 00 00 00 |................| 0006c910 00 00 00 01 02 03 00 00 00 00 00 00 00 00 00 00 |................| 0006c920 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 0006e540 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff |................| 0006e550 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00070000 0c 79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |.y..............| Erasing and Writing doesn't work. :( Greets, Henne

1 0

A8JM flashrom unable to erase
by Deathstalker 06 Feb '10

06 Feb '10

When I logged onto irc: <james_l> I have an odd case, and I was wondering if it'd be possible for someone to help: I have an a8jm laptop (Core (1) Duo) which burnt out a video card. Fortunately it is an MXM card (sorta), so it's replaceable. Unfortunately, I managed to order the wrong card for the next model. While it boots, and no display is shown at all. It's been suggested that the current bios would enable it to work, unfortunately flashrom recognizes the chip but is <james_l> unable to erase it before writing it. <james_l> This is the output: http://coreboot.pastebin.com/m660c2a4a <james_l> Oh, and I have successfully dumped the current bios. <macavity> james_l: most people here are currently at FOSDEM.. you may not get help emidiately <macavity> !summary james_l <flashrom_bot> james_l: please mail the output of 'flashrom -V', 'lspci -nnvvvxxx', 'superiotool -deV' (all commands as root), the exact name of your board (including revision, if there are multiple revisions), and a link to the official BIOS download to flashrom(a)flashrom.org <macavity> including your problem that is :P <james_l> Alright I have since then done some more looking and modified a bios so that it will work (At least I'm fairly certain it will anyway). Even if that doesn't, in both cases I need to flash the ROM, which is failing to do so. I can read from it, which is how I can tell I currently have bios 209. Thank you in advance. Per the above: I'm unable to get a direct (or even to the model) from ASUS's download site, best I can do is provide a link to it, and what information you need. http://support.asus.com/download/download.aspx?SLanguage=en-us Product: Notebook Series: A8 Model A8JM The board revision, is I believe revision 2.0 (I'm not absolutely certain on that) james@james-rescue:~$ sudo flashrom -V Calibrating delay loop... 522M loops per second, 100 myus = 200 us. OK. No coreboot table found. Found chipset "Intel ICH7M", enabling flash write... BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 Root Complex Register Block address = 0xfed1c000 GCS = 0xa20c60: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x3 (LPC) Top Swap : not enabled OK. Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff Probing for ASD AE49F2008, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Atmel AT25DF021, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF041A, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF081, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF161, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF321, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF321A, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25DF641, 8192 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25F512B, 64 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25FS010, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT25FS040, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT26DF041, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT26DF081A, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT26DF161, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT26DF161A, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT26F004, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Atmel AT45CS1282, 16896 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB011D, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB021D, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB041D, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB081D, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB161D, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB321C, 4224 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB321D, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT45DB642D, 8192 KB: spi_command called, but no SPI chipset/strapping detected Probing for Atmel AT49F002(N), 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for AMIC A25L40P, 512 KB: 4b ID not supported on this SPI controller Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xbf, id2 0x60 Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xbf, id2 0x60 Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMIC A49LF040A, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for EMST F49B002UA, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L1005, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L2005, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L4005, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L8005, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L1605, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L3205, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX25L6405, 8192 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xbf, id2 0x60 Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xbf, id2 0x60 Probing for Macronix MX29LV040C, 512 KB: probe_29f002: id1 0xbf, id2 0x60 Probing for Numonyx M25PE10, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for Numonyx M25PE20, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Numonyx M25PE40, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Numonyx M25PE80, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Numonyx M25PE16, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV010, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV016B, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV020, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV040, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV080B, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm25LV512, 64 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC Pm49FL002, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for PMC Pm49FL004, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0xff, id2 0xff Probing for Spansion S25FL016A, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST SST25VF016B, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST SST25VF032B, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST SST25VF040B, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST SST25VF080B, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0xff, id2 0xff Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST29EE020A, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF002A/B, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF003A/B, 384 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF004A/B, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Found chip "SST SST49LF004A/B" (512 KB) at physical address 0xfff80000. Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF008A, 1024 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF040B, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF080A, 1024 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P10-A, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P20, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P40, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P40-old, 512 KB: spi_command called, but no SPI chipset/strapping detected spi_command called, but no SPI chipset/strapping detected Probing for ST M25P80, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P16, 2048 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P32, 4096 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P64, 8192 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M25P128, 16384 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST M29F002B, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for ST M29F002T/NT, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for ST M29W040B, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x60 Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x60 Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x60 Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x60 Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SyncMOS S29C31004T, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51001T, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51002T, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51004T, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W25x10, 128 KB: spi_command called, but no SPI chipset/strapping detected Probing for Winbond W25x20, 256 KB: spi_command called, but no SPI chipset/strapping detected Probing for Winbond W25x40, 512 KB: spi_command called, but no SPI chipset/strapping detected Probing for Winbond W25x80, 1024 KB: spi_command called, but no SPI chipset/strapping detected Probing for Winbond W29C011, 128 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W29EE011, 128 KB: === Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. === Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0xbf, id2 0x60 Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W49F002U, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W49V002FA, 256 KB: probe_jedec: id1 0xbf, id2 0x60 Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: vid 0xbf, did 0x60 Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: vid 0xbf, did 0x60 Probing for Atmel unknown Atmel SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected Probing for EON unknown EON SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected Probing for Macronix unknown Macronix SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected Probing for PMC unknown PMC SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected Probing for SST unknown SST SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected Probing for ST unknown ST SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected No operations were specified. ---- james@james-rescue:~$ lspci -nnvvvxxx 00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: intel-agp 00: 86 80 a0 27 06 00 90 20 03 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa000000-fe0fffff Prefetchable memory behind bridge: 00000000bdf00000-00000000ddefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 a1 27 07 05 10 00 03 00 04 06 08 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 b0 b0 00 00 20: 00 fa 00 fe f1 bd e1 dd 00 00 00 00 00 00 00 00 30: 00 00 00 00 88 00 00 00 00 00 00 00 0a 01 0a 00 00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:1153] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00: 86 80 d8 27 06 00 10 00 02 00 03 04 08 00 00 00 10: 04 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 53 11 30: 00 00 00 00 50 00 00 00 00 00 00 00 0f 01 00 00 00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 d0 27 04 05 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 f0 00 00 20 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00 00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fe100000-fe1fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 d4 27 07 05 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 c0 c0 00 00 20: 10 fe 10 fe f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 03 02 00 00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 02) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 d6 27 04 05 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 04 05 00 f0 00 00 20 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 04 02 00 00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at ec00 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 c8 27 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 ec 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 00 00 00 00 00 00 00 00 04 01 00 00 00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at e880 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 c9 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 e8 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00 00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 20 Region 4: I/O ports at e800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 ca 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 00 00 00 00 00 00 00 00 06 03 00 00 00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 22 Region 4: I/O ports at e480 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 cb 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 e4 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 04 00 00 00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at febfbc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00: 86 80 cc 27 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 bc bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 50 00 00 00 00 00 00 00 04 01 00 00 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fea00000-feafffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00: 86 80 48 24 06 01 10 00 e2 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 06 06 20 f0 00 80 22 20: a0 fe a0 fe f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02) Subsystem: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt, intel-rng 00: 86 80 b9 27 07 00 10 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 b9 27 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at ffa0 [size=16] Kernel driver in use: ata_piix 00: 86 80 df 27 05 00 88 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 f1 08 00 00 f9 08 00 00 20: a1 ff 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce Go 7700 [10de:0397] (rev a1) Subsystem: ASUSTeK Computer Inc. Device [1043:1232] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M] Region 5: I/O ports at bc00 [size=128] Expansion ROM at fe0e0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb 00: de 10 97 03 07 00 10 00 a1 00 00 03 08 00 00 00 10: 00 00 00 fd 0c 00 00 c0 00 00 00 00 04 00 00 fc 20: 00 00 00 00 01 bc 00 00 00 00 00 00 43 10 32 12 30: 00 00 0e fe 60 00 00 00 00 00 00 00 0a 01 00 00 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01) Subsystem: ASUSTeK Computer Inc. Device [1043:11f5] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 2299 Region 0: I/O ports at c800 [size=256] Region 2: Memory at fe1ff000 (64-bit, non-prefetchable) [size=4K] Expansion ROM at fe1e0000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 00: ec 10 68 81 07 04 10 00 01 00 00 02 08 00 00 00 10: 01 c8 00 00 00 00 00 00 04 f0 1f fe 00 00 00 00 20: 00 00 00 00 00 00 00 00 02 01 00 00 43 10 f5 11 30: 00 00 1e fe 40 00 00 00 00 00 00 00 0b 01 00 00 06:00.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (prog-if 10) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (500ns min, 1000ns max) Interrupt: pin B routed to IRQ 17 Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ohci1394 Kernel modules: firewire-ohci, ohci1394 00: 80 11 32 08 06 00 10 02 00 10 00 0c 00 40 80 00 10: 00 f8 af fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 02 02 04 06:00.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 19) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin B routed to IRQ 17 Region 0: Memory at feaff400 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 00: 80 11 22 08 06 00 10 02 19 00 05 08 00 40 80 00 10: 00 f4 af fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00 06:00.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 0a) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ricoh-mmc Kernel modules: ricoh_mmc 00: 80 11 92 05 02 00 10 02 0a 00 80 08 00 00 80 00 10: 00 ec af fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00 06:00.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 05) Subsystem: ASUSTeK Computer Inc. Device [1043:1287] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 0: Memory at feafec00 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> 00: 80 11 52 08 02 00 10 02 05 00 80 08 00 00 80 00 10: 00 e8 af fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 87 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00 06:00.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev ff) (prog-if ff) !!! Unknown header type 7f 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff --- james@james-rescue:~$ sudo superiotool -deV superiotool r3695 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x2e... Failed. Returned data: id=0x0000, rev=0x0 Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x0000, rev=0x0 Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0x7a, rev=0x01 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff No Super I/O found

1 0

Winbond W29C020C Flashrom Test
by amiga600dev＠yahoo.de 06 Feb '10

06 Feb '10

Hi there, here are the sucessful test results for: Winbond W29C020C @ Intel PIIX4/4E/4M flash part is marked UNTESTED so far Greetings Erik

1 0

'flashrom -V', 'lspci -nnvvvxxx', 'superiotool -deV' outputs for XFX nFORCE 630I GEFORCE 7150 SOCKET 775 (Product Code: MG-63MI-7159)
by Maik Masling 06 Feb '10

06 Feb '10

1 0

[PATCH] Add Eon EN29LV800(B)(C){B,T} recognition
by TJ 05 Feb '10

05 Feb '10

Add initial recognition for the EON EN29LV800(B)(C){B,T}. The datasheet can be found at: http://www.essi.com.tw/upfile/p20097114268.pdf I'm not yet clear what CHIP_BUSTYPE it uses. The chip is used on Sony Vaio VGN-FE41 and similar models but will require some board enable measures. --- flashchips.c | 64 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 2 + 2 files changed, 66 insertions(+), 0 deletions(-) diff --git a/flashchips.c b/flashchips.c index f66b95a..2953dd6 100644 --- a/flashchips.c +++ b/flashchips.c @@ -2165,6 +2165,70 @@ struct flashchip flashchips[] = { { .vendor = "EON", + .name = "EN29LV800(B)(C)B", + .bustype = CHIP_BUSTYPE_UNKNOWN, + .manufacture_id = EON_ID, + .model_id = EN_29LV800B, + .total_size = 1024, + .page_size = 1024, // TODO: check this + .feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* TODO: check Datasheet has no timing info specified */ + .erase = NULL, + .block_erasers = + { + { + .eraseblocks = { + {16 * 1024, 1}, + {8 * 1024, 2}, + {32 * 1024, 1}, + {64 * 1024, 15}, + }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + }, + }, + .write = NULL, + .read = read_memmapped, + }, + + { + .vendor = "EON", + .name = "EN29LV800(B)(C)T", + .bustype = CHIP_BUSTYPE_UNKNOWN, + .manufacture_id = EON_ID, + .model_id = EN_29LV800T, + .total_size = 1024, + .page_size = 1024, // TODO: check this + .feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* TODO: check Datasheet has no timing info specified */ + .erase = NULL, + .block_erasers = + { + { + .eraseblocks = { + {64 * 1024, 15}, + {32 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + }, + }, + .write = NULL, + .read = read_memmapped, + }, + + { + .vendor = "EON", .name = "EN29F002(A)(N)B", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = EON_ID, diff --git a/flashchips.h b/flashchips.h index e299852..8a72cb0 100644 --- a/flashchips.h +++ b/flashchips.h @@ -200,6 +200,8 @@ #define EN_29F040A 0x7F04 #define EN_29LV010 0x7F6E #define EN_29LV040A 0x7F4F /* EN_29LV040(A) */ +#define EN_29LV800B 0x7F5B /* EN29LV800/B/C */ +#define EN_29LV800T 0x7FDA #define EN_29F002T 0x7F92 /* Same as EN29F002A */ #define EN_29F002B 0x7F97 /* Same as EN29F002AN */ -- 1.6.3.3

1 0

flashroom success with msi 7321 v1.0 mb (k9MM-V)
by David Mears 05 Feb '10

05 Feb '10

seems to hose the MAC address on the onboard lan, though.

1 0

building 32-bit on 64-bit
by ron minnich 04 Feb '10

04 Feb '10

I'm sorry if there is an obvious answer but how is that done? thanks ron

2 1

[PATCH] Locking infrastructure and locking for W39V080FA and PMC 49LF040
by Sean Nelson 04 Feb '10

04 Feb '10

Locking infrastructure Add lock-status command option. Winbond W39V080FA has 64k lock blocks. PMC Pm49FL004 has 64k lock blocks. Tested, but write/erase fails. PMC Pm49FL002 has 32k lock blocks. Signed-off-by: Sean Nelson <audiohacked(a)gmail.com> --- Added dumps from an Compaq desktop with ASUS A8N-LA; just in case. Stepan if you could please test this and tell me if it works or not.

2 2

Call for photos: External programmers
by Carl-Daniel Hailfinger 04 Feb '10

04 Feb '10

Hi, I'd like to spice up my FOSDEM presentation with a few photos of supported (and WIP) external programmers. If you have any photos of SiliconImage SATA, Highpoint IDE, Nvidia graphics etc, please mail them to me or point me to a place where I can download them. Thanks! Regards, Carl-Daniel -- Developer quote of the year: "We are juggling too many chainsaws and flaming arrows and tigers."

1 0

test report
by Solomon Peachy 04 Feb '10

04 Feb '10

sudo ./flashrom flashrom v0.9.1-r893 No coreboot table found. sh: dmidecode: command not found Found ITE SuperI/O, id 8716 Found chipset "NVIDIA MCP51", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... OK. Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. I've sucecssfully flashed this part with the 0.9.1 release, on a PCCHIPS A11G motherboard. - Solomon -- Solomon Peachy solomon(a)linux-wlan.com AbsoluteValue Systems http://www.linux-wlan.com 721-D North Drive +1 (321) 259-0737 (office) Melbourne, FL 32934 +1 (321) 259-0286 (fax)

1 0

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom February 2010