Author: hailfinger Date: Sat Jul 10 18:56:32 2010 New Revision: 1073 URL: http://flashrom.org/trac/coreboot/changeset/1073
Log: Autodetect the ITE IT8705 Super I/O and enable flash writes if it performs LPC->Parallel translation. Remove board enables which triggered the IT8705 write enable manually. Change the IT87 SPI special case to cover IT87 LPC->SPI and LPC->Parallel translation.
Signed-off-by: Carl-Daniel Hailfinger c-d.hailfinger.devel.2006@gmx.net
Tested on Syntax SV266A. Acked-by: Paul Menzel paulepanter@users.sourceforge.net
Tested on Shuttle AK38N, all operations work fine. Acked-by: Uwe Hermann uwe@hermann-uwe.de
Modified: trunk/board_enable.c trunk/flash.h trunk/internal.c trunk/it87spi.c
Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Thu Jul 8 12:13:37 2010 (r1072) +++ trunk/board_enable.c Sat Jul 10 18:56:32 2010 (r1073) @@ -390,31 +390,92 @@ }
/** - * + * Suited for all boards with ITE IT8705F. + * The SIS950 Super I/O probably requires a similar flash write enable. */ -static int it8705f_write_enable(uint8_t port) +int it8705f_write_enable(uint8_t port) { + uint8_t tmp; + int ret = 0; + enter_conf_mode_ite(port); - sio_mask(port, 0x24, 0x04, 0x04); /* Flash ROM I/F Writes Enable */ + tmp = sio_read(port, 0x24); + /* Check if at least one flash segment is enabled. */ + if (tmp & 0xf0) { + /* The IT8705F will respond to LPC cycles and translate them. */ + buses_supported = CHIP_BUSTYPE_PARALLEL; + /* Flash ROM I/F Writes Enable */ + tmp |= 0x04; + msg_pdbg("Enabling IT8705F flash ROM interface write.\n"); + if (tmp & 0x02) { + /* The data sheet contradicts itself about max size. */ + max_rom_decode.parallel = 1024 * 1024; + msg_pinfo("IT8705F with very unusual settings. Please " + "send the output of "flashrom -V" to \n" + "flashrom@flashrom.org to help us finish " + "support for your Super I/O. Thanks.\n"); + ret = 1; + } else if (tmp & 0x08) { + max_rom_decode.parallel = 512 * 1024; + } else { + max_rom_decode.parallel = 256 * 1024; + } + /* Safety checks. The data sheet is unclear here: Segments 1+3 + * overlap, no segment seems to cover top - 1MB to top - 512kB. + * We assume that certain combinations make no sense. + */ + if (((tmp & 0x02) && !(tmp & 0x08)) || /* 1 MB en, 512 kB dis */ + (!(tmp & 0x10)) || /* 128 kB dis */ + (!(tmp & 0x40))) { /* 256/512 kB dis */ + msg_perr("Inconsistent IT8705F decode size!\n"); + ret = 1; + } + if (sio_read(port, 0x25) != 0) { + msg_perr("IT8705F flash data pins disabled!\n"); + ret = 1; + } + if (sio_read(port, 0x26) != 0) { + msg_perr("IT8705F flash address pins 0-7 disabled!\n"); + ret = 1; + } + if (sio_read(port, 0x27) != 0) { + msg_perr("IT8705F flash address pins 8-15 disabled!\n"); + ret = 1; + } + if ((sio_read(port, 0x29) & 0x10) != 0) { + msg_perr("IT8705F flash write enable pin disabled!\n"); + ret = 1; + } + if ((sio_read(port, 0x29) & 0x08) != 0) { + msg_perr("IT8705F flash chip select pin disabled!\n"); + ret = 1; + } + if ((sio_read(port, 0x29) & 0x04) != 0) { + msg_perr("IT8705F flash read strobe pin disabled!\n"); + ret = 1; + } + if ((sio_read(port, 0x29) & 0x03) != 0) { + msg_perr("IT8705F flash address pins 16-17 disabled!\n"); + /* Not really an error if you use flash chips smaller + * than 256 kByte, but such a configuration is unlikely. + */ + ret = 1; + } + msg_pdbg("Maximum IT8705F parallel flash decode size is %u.\n", + max_rom_decode.parallel); + if (ret) { + msg_pinfo("Not enabling IT8705F flash write.\n"); + } else { + sio_write(port, 0x24, tmp); + } + } else { + msg_pdbg("No IT8705F flash segment enabled.\n"); + /* Not sure if this is an error or not. */ + ret = 0; + } exit_conf_mode_ite(port);
- return 0; -} - -/** - * Suited for: - * - AOpen vKM400Am-S: VIA KM400 + VT8237 + IT8705F. - * - Biostar P4M80-M4: VIA P4M800 + VT8237 + IT8705AF - * - Elitegroup K7S6A: SiS745 + ITE IT8705F - * - Elitegroup K7VTA3: VIA Apollo KT266/A/333 + VIA VT8235 + ITE IT8705F - * - GIGABYTE GA-7VT600: VIA KT600 + VT8237 + IT8705 - * - Shuttle AK38N: VIA KT333CF + VIA VT8235 + ITE IT8705F - * - * The SIS950 Super I/O probably requires the same flash write enable. - */ -static int it8705f_write_enable_2e(void) -{ - return it8705f_write_enable(0x2e); + return ret; }
static int pc87360_gpio_set(uint8_t gpio, int raise) @@ -1590,7 +1651,6 @@ {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, {0x1022, 0x746B, 0, 0, 0, 0, 0, 0, NULL, "AGAMI", "ARUMA", "agami", "Aruma", 0, OK, w83627hf_gpio24_raise_2e}, {0x1106, 0x3177, 0x17F2, 0x3177, 0x1106, 0x3148, 0x17F2, 0x3148, NULL, NULL, NULL, "Albatron", "PM266A Pro", 0, OK, w836xx_memw_enable_2e}, - {0x1106, 0x3205, 0x1106, 0x3205, 0x10EC, 0x8139, 0xA0A0, 0x0477, NULL, NULL, NULL, "AOpen", "vKM400Am-S", 0, OK, it8705f_write_enable_2e}, {0x1022, 0x2090, 0, 0, 0x1022, 0x2080, 0, 0, NULL, "artecgroup", "dbe61", "Artec Group", "DBE61", 0, OK, board_artecgroup_dbe6x}, {0x1022, 0x2090, 0, 0, 0x1022, 0x2080, 0, 0, NULL, "artecgroup", "dbe62", "Artec Group", "DBE62", 0, OK, board_artecgroup_dbe6x}, {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, @@ -1611,14 +1671,11 @@ {0x8086, 0x2570, 0x1043, 0x80F2, 0x105A, 0x3373, 0x1043, 0x80F5, NULL, NULL, NULL, "ASUS", "P4P800-E Deluxe", 0, OK, intel_ich_gpio21_raise}, {0x10B9, 0x1541, 0, 0, 0x10B9, 0x1533, 0, 0, "^P5A$", "asus", "p5a", "ASUS", "P5A", 0, OK, board_asus_p5a}, {0x10DE, 0x0030, 0x1043, 0x818a, 0x8086, 0x100E, 0x1043, 0x80EE, NULL, NULL, NULL, "ASUS", "P5ND2-SLI Deluxe", 0, OK, nvidia_mcp_gpio10_raise}, - {0x1106, 0x3149, 0x1565, 0x3206, 0x1106, 0x3344, 0x1565, 0x1202, NULL, NULL, NULL, "Biostar", "P4M80-M4", 0, OK, it8705f_write_enable_2e}, {0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, NULL, "Dell", "PowerEdge 1850", 0, OK, intel_ich_gpio23_raise}, - {0x1039, 0x5513, 0x1019, 0x0A41, 0x1039, 0x0018, 0, 0, NULL, NULL, NULL, "Elitegroup", "K7S6A", 0, OK, it8705f_write_enable_2e}, - {0x1106, 0x3038, 0x1019, 0x0996, 0x1106, 0x3177, 0x1019, 0x0996, NULL, NULL, NULL, "Elitegroup", "K7VTA3", 256, OK, it8705f_write_enable_2e}, + {0x1106, 0x3038, 0x1019, 0x0996, 0x1106, 0x3177, 0x1019, 0x0996, NULL, NULL, NULL, "Elitegroup", "K7VTA3", 256, OK, NULL}, {0x1106, 0x3177, 0x1106, 0x3177, 0x1106, 0x3059, 0x1695, 0x3005, NULL, NULL, NULL, "EPoX", "EP-8K5A2", 0, OK, w836xx_memw_enable_2e}, {0x10EC, 0x8139, 0x1695, 0x9001, 0x11C1, 0x5811, 0x1695, 0x9015, NULL, NULL, NULL, "EPoX", "EP-8RDA3+", 0, OK, nvidia_mcp_gpio31_raise}, {0x8086, 0x7110, 0, 0, 0x8086, 0x7190, 0, 0, NULL, "epox", "ep-bx3", "EPoX", "EP-BX3", 0, OK, board_epox_ep_bx3}, - {0x1106, 0x3227, 0x1458, 0x5001, 0x10ec, 0x8139, 0x1458, 0xe000, NULL, NULL, NULL, "GIGABYTE", "GA-7VT600", 0, OK, it8705f_write_enable_2e}, {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, {0x10DE, 0x0050, 0x1458, 0x0C11, 0x10DE, 0x005e, 0x1458, 0x5000, NULL, NULL, NULL, "GIGABYTE", "GA-K8N-SLI", 0, OK, nvidia_mcp_gpio21_raise}, {0x1166, 0x0223, 0x103c, 0x320d, 0x14e4, 0x1678, 0x103c, 0x703e, NULL, "hp", "dl145_g3", "HP", "DL145 G3", 0, OK, board_hp_dl145_g3_enable}, @@ -1644,7 +1701,7 @@ {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, {0x1011, 0x0019, 0xaa55, 0xaa55, 0x8086, 0x7190, 0, 0, NULL, NULL, NULL, "Nokia", "IP530", 0, OK, fdc37b787_gpio50_raise_3f0}, {0x1106, 0x3099, 0, 0, 0x1106, 0x3074, 0, 0, NULL, "shuttle", "ak31", "Shuttle", "AK31", 0, OK, w836xx_memw_enable_2e}, - {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, it8705f_write_enable_2e}, + {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, NULL}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, NULL, "Shuttle", "FN25", 0, OK, board_shuttle_fn25}, {0x1106, 0x3038, 0x0925, 0x1234, 0x1106, 0x3058, 0x15DD, 0x7609, NULL, NULL, NULL, "Soyo", "SY-7VCA", 0, OK, via_apollo_gpo0_lower}, {0x1106, 0x3038, 0x0925, 0x1234, 0x1106, 0x0596, 0x1106, 0, NULL, NULL, NULL, "Tekram", "P6Pro-A5", 256, OK, NULL},
Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Thu Jul 8 12:13:37 2010 (r1072) +++ trunk/flash.h Sat Jul 10 18:56:32 2010 (r1073) @@ -350,6 +350,7 @@ /* board_enable.c */ void w836xx_ext_enter(uint16_t port); void w836xx_ext_leave(uint16_t port); +int it8705f_write_enable(uint8_t port); uint8_t sio_read(uint16_t port, uint8_t reg); void sio_write(uint16_t port, uint8_t reg, uint8_t data); void sio_mask(uint16_t port, uint8_t reg, uint8_t data, uint8_t mask); @@ -692,12 +693,11 @@ int ich_spi_send_multicommand(struct spi_command *cmds);
/* it87spi.c */ -extern uint16_t it8716f_flashport; void enter_conf_mode_ite(uint16_t port); void exit_conf_mode_ite(uint16_t port); struct superio probe_superio_ite(void); +int init_superio_ite(void); int it87spi_init(void); -int it87xx_probe_spi_flash(const char *name); int it8716f_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len);
Modified: trunk/internal.c ============================================================================== --- trunk/internal.c Thu Jul 8 12:13:37 2010 (r1072) +++ trunk/internal.c Sat Jul 10 18:56:32 2010 (r1073) @@ -229,8 +229,10 @@ }
#if defined(__i386__) || defined(__x86_64__) - /* Probe for IT87* LPC->SPI translation unconditionally. */ - it87xx_probe_spi_flash(NULL); + /* Probe unconditionally for IT87* LPC->SPI translation and for + * IT87* Parallel write enable. + */ + init_superio_ite(); #endif
board_flash_enable(lb_vendor, lb_part);
Modified: trunk/it87spi.c ============================================================================== --- trunk/it87spi.c Thu Jul 8 12:13:37 2010 (r1072) +++ trunk/it87spi.c Sat Jul 10 18:56:32 2010 (r1073) @@ -96,90 +96,109 @@ return ret; }
-static uint16_t find_ite_spi_flash_port(uint16_t port, uint16_t id) +static uint16_t it87spi_probe(uint16_t port) { uint8_t tmp = 0; char *portpos = NULL; uint16_t flashport = 0;
- switch (id) { - case 0x8716: - case 0x8718: - case 0x8720: - enter_conf_mode_ite(port); - /* NOLDN, reg 0x24, mask out lowest bit (suspend) */ - tmp = sio_read(port, 0x24) & 0xFE; - /* If IT87SPI was not explicitly selected, we want to check - * quickly if LPC->SPI translation is active. - */ - if ((programmer == PROGRAMMER_INTERNAL) && !(tmp & (0x0E))) { - msg_pdbg("No IT87* serial flash segment enabled.\n"); - exit_conf_mode_ite(port); - break; - } - msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", - 0xFFFE0000, 0xFFFFFFFF, (tmp & 1 << 1) ? "en" : "dis"); - msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", - 0x000E0000, 0x000FFFFF, (tmp & 1 << 1) ? "en" : "dis"); - msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", - 0xFFEE0000, 0xFFEFFFFF, (tmp & 1 << 2) ? "en" : "dis"); - msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", - 0xFFF80000, 0xFFFEFFFF, (tmp & 1 << 3) ? "en" : "dis"); - msg_pdbg("LPC write to serial flash %sabled\n", - (tmp & 1 << 4) ? "en" : "dis"); - /* The LPC->SPI force write enable below only makes sense for - * non-programmer mode. + enter_conf_mode_ite(port); + /* NOLDN, reg 0x24, mask out lowest bit (suspend) */ + tmp = sio_read(port, 0x24) & 0xFE; + /* If IT87SPI was not explicitly selected, we want to check + * quickly if LPC->SPI translation is active. + */ + if ((programmer == PROGRAMMER_INTERNAL) && !(tmp & (0x0E))) { + msg_pdbg("No IT87* serial flash segment enabled.\n"); + exit_conf_mode_ite(port); + /* Nothing to do. */ + return 1; + } + msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", + 0xFFFE0000, 0xFFFFFFFF, (tmp & 1 << 1) ? "en" : "dis"); + msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", + 0x000E0000, 0x000FFFFF, (tmp & 1 << 1) ? "en" : "dis"); + msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", + 0xFFEE0000, 0xFFEFFFFF, (tmp & 1 << 2) ? "en" : "dis"); + msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", + 0xFFF80000, 0xFFFEFFFF, (tmp & 1 << 3) ? "en" : "dis"); + msg_pdbg("LPC write to serial flash %sabled\n", + (tmp & 1 << 4) ? "en" : "dis"); + /* The LPC->SPI force write enable below only makes sense for + * non-programmer mode. + */ + /* If any serial flash segment is enabled, enable writing. */ + if ((tmp & 0xe) && (!(tmp & 1 << 4))) { + msg_pdbg("Enabling LPC write to serial flash\n"); + tmp |= 1 << 4; + sio_write(port, 0x24, tmp); + } + msg_pdbg("Serial flash pin %i\n", (tmp & 1 << 5) ? 87 : 29); + /* LDN 0x7, reg 0x64/0x65 */ + sio_write(port, 0x07, 0x7); + flashport = sio_read(port, 0x64) << 8; + flashport |= sio_read(port, 0x65); + msg_pdbg("Serial flash port 0x%04x\n", flashport); + /* Non-default port requested? */ + portpos = extract_programmer_param("it87spiport"); + if (portpos) { + char *endptr = NULL; + unsigned long forced_flashport; + forced_flashport = strtoul(portpos, &endptr, 0); + /* Port 0, port >0x1000, unaligned ports and garbage strings + * are rejected. */ - /* If any serial flash segment is enabled, enable writing. */ - if ((tmp & 0xe) && (!(tmp & 1 << 4))) { - msg_pdbg("Enabling LPC write to serial flash\n"); - tmp |= 1 << 4; - sio_write(port, 0x24, tmp); - } - msg_pdbg("Serial flash pin %i\n", (tmp & 1 << 5) ? 87 : 29); - /* LDN 0x7, reg 0x64/0x65 */ - sio_write(port, 0x07, 0x7); - flashport = sio_read(port, 0x64) << 8; - flashport |= sio_read(port, 0x65); - msg_pdbg("Serial flash port 0x%04x\n", flashport); - /* Non-default port requested? */ - portpos = extract_programmer_param("it87spiport"); - if (portpos && strlen(portpos)) { - flashport = strtol(portpos, (char **)NULL, 0); - msg_pinfo("Forcing serial flash port 0x%04x\n", - flashport); - sio_write(port, 0x64, (flashport >> 8)); - sio_write(port, 0x65, (flashport & 0xff)); - } else if (portpos) { - msg_perr("Error: it87spiport specified, but no port " - "given.\n"); + if (!forced_flashport || (forced_flashport >= 0x1000) || + (forced_flashport & 0x7) || (*endptr != '\0')) { + /* Using ports below 0x100 is a really bad idea, and + * should only be done if no port between 0x100 and + * 0xff8 works due to routing issues. + */ + msg_perr("Error: it87spiport specified, but no valid " + "port specified.\nPort must be a multiple of " + "0x8 and lie between 0x100 and 0xff8.\n"); free(portpos); /* FIXME: Return failure here once it87spi_common_init() * can handle the return value sanely. */ exit(1); + } else { + flashport = (uint16_t)forced_flashport; + msg_pinfo("Forcing serial flash port 0x%04x\n", + flashport); + sio_write(port, 0x64, (flashport >> 8)); + sio_write(port, 0x65, (flashport & 0xff)); } - free(portpos); - exit_conf_mode_ite(port); - break; - /* TODO: Handle more IT87xx if they support flash translation */ - default: - msg_pdbg("SuperI/O ID %04hx is not on the controller list.\n", id); } - return flashport; + free(portpos); + exit_conf_mode_ite(port); + it8716f_flashport = flashport; + if (buses_supported & CHIP_BUSTYPE_SPI) + msg_pdbg("Overriding chipset SPI with IT87 SPI.\n"); + spi_controller = SPI_CONTROLLER_IT87XX; + buses_supported |= CHIP_BUSTYPE_SPI; + return 0; }
-int it87spi_common_init(void) +int init_superio_ite(void) { if (superio.vendor != SUPERIO_VENDOR_ITE) return 1;
- it8716f_flashport = find_ite_spi_flash_port(superio.port, superio.model); - - if (it8716f_flashport) - spi_controller = SPI_CONTROLLER_IT87XX; - - return (!it8716f_flashport); + switch (superio.model) { + case 0x8705: + return it8705f_write_enable(superio.port); + break; + case 0x8716: + case 0x8718: + case 0x8720: + return it87spi_probe(superio.port); + break; + default: + msg_pdbg("Super I/O ID 0x%04hx is not on the list of flash " + "capable controllers.\n", superio.model); + } + return 1; }
@@ -190,7 +209,7 @@ get_io_perms(); /* Probe for the Super I/O chip and fill global struct superio. */ probe_superio(); - ret = it87spi_common_init(); + ret = init_superio_ite(); if (!ret) { buses_supported = CHIP_BUSTYPE_SPI; } else { @@ -198,19 +217,6 @@ } return ret; } - -int it87xx_probe_spi_flash(const char *name) -{ - int ret; - - ret = it87spi_common_init(); - if (!ret) { - if (buses_supported & CHIP_BUSTYPE_SPI) - msg_pdbg("Overriding chipset SPI with IT87 SPI.\n"); - buses_supported |= CHIP_BUSTYPE_SPI; - } - return ret; -}
/* * The IT8716F only supports commands with length 1,2,4,5 bytes including
-
repository service