Signed-off-by: Michael Karcher flashrom@mkarcher.dialup.fu-berlin.de --- chipset_enable.c | 202 +-------------------------------------------------- flash.h | 6 +- ichspi.c | 214 +++++++++++++++++++++++++++++++++++++++++++++++++++++- 3 files changed, 218 insertions(+), 204 deletions(-)
diff --git a/chipset_enable.c b/chipset_enable.c index dc0e55f..7434d65 100644 --- a/chipset_enable.c +++ b/chipset_enable.c @@ -417,69 +417,15 @@ static int enable_flash_poulsbo(struct pci_dev *dev, const char *name)
static int enable_flash_vt8237s_spi(struct pci_dev *dev, const char *name) { - uint32_t mmio_base; - /* Do we really need no write enable? */ - mmio_base = (pci_read_long(dev, 0xbc)) << 8; - msg_pdbg("MMIO base at = 0x%x\n", mmio_base); - ich_spibar = physmap("VT8237S MMIO registers", mmio_base, 0x70); - - msg_pdbg("0x6c: 0x%04x (CLOCK/DEBUG)\n", - mmio_readw(ich_spibar + 0x6c)); - - /* Not sure if it speaks all these bus protocols. */ - buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; - spi_controller = SPI_CONTROLLER_VIA; - ich_init_opcodes(); - - return 0; -} - -#define ICH_BMWAG(x) ((x >> 24) & 0xff) -#define ICH_BMRAG(x) ((x >> 16) & 0xff) -#define ICH_BRWA(x) ((x >> 8) & 0xff) -#define ICH_BRRA(x) ((x >> 0) & 0xff) - -#define ICH_FREG_BASE(x) ((x >> 0) & 0x1fff) -#define ICH_FREG_LIMIT(x) ((x >> 16) & 0x1fff) - -static void do_ich9_spi_frap(uint32_t frap, int i) -{ - const char *access_names[4] = { - "locked", "read-only", "write-only", "read-write" - }; - const char *region_names[5] = { - "Flash Descriptor", "BIOS", "Management Engine", - "Gigabit Ethernet", "Platform Data" - }; - uint32_t base, limit; - int rwperms = (((ICH_BRWA(frap) >> i) & 1) << 1) | - (((ICH_BRRA(frap) >> i) & 1) << 0); - int offset = 0x54 + i * 4; - uint32_t freg = mmio_readl(ich_spibar + offset); - - msg_pdbg("0x%02X: 0x%08x (FREG%i: %s)\n", - offset, freg, i, region_names[i]); - - base = ICH_FREG_BASE(freg); - limit = ICH_FREG_LIMIT(freg); - if (base == 0x1fff && limit == 0) { - /* this FREG is disabled */ - msg_pdbg("%s region is unused.\n", region_names[i]); - return; - } - - msg_pdbg("0x%08x-0x%08x is %s\n", - (base << 12), (limit << 12) | 0x0fff, - access_names[rwperms]); + return via_init_spi(dev); }
static int enable_flash_ich_dc_spi(struct pci_dev *dev, const char *name, int ich_generation) { - int ret, i; - uint8_t old, new, bbs, buc; - uint16_t spibar_offset, tmp2; + int ret; + uint8_t bbs, buc; uint32_t tmp, gcs; void *rcrb; //TODO: These names are incorrect for EP80579. For that, the solution would look like the commented line @@ -518,147 +464,7 @@ static int enable_flash_ich_dc_spi(struct pci_dev *dev, const char *name, return ret; }
- switch (ich_generation) { - case 7: - buses_supported = CHIP_BUSTYPE_SPI; - spi_controller = SPI_CONTROLLER_ICH7; - spibar_offset = 0x3020; - break; - case 8: - buses_supported = CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; - spi_controller = SPI_CONTROLLER_ICH9; - spibar_offset = 0x3020; - break; - case 9: - case 10: - default: /* Future version might behave the same */ - buses_supported = CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; - spi_controller = SPI_CONTROLLER_ICH9; - spibar_offset = 0x3800; - break; - } - - /* SPIBAR is at RCRB+0x3020 for ICH[78] and RCRB+0x3800 for ICH9. */ - msg_pdbg("SPIBAR = 0x%x + 0x%04x\n", tmp, spibar_offset); - - /* Assign Virtual Address */ - ich_spibar = rcrb + spibar_offset; - - switch (spi_controller) { - case SPI_CONTROLLER_ICH7: - msg_pdbg("0x00: 0x%04x (SPIS)\n", - mmio_readw(ich_spibar + 0)); - msg_pdbg("0x02: 0x%04x (SPIC)\n", - mmio_readw(ich_spibar + 2)); - msg_pdbg("0x04: 0x%08x (SPIA)\n", - mmio_readl(ich_spibar + 4)); - for (i = 0; i < 8; i++) { - int offs; - offs = 8 + (i * 8); - msg_pdbg("0x%02x: 0x%08x (SPID%d)\n", offs, - mmio_readl(ich_spibar + offs), i); - msg_pdbg("0x%02x: 0x%08x (SPID%d+4)\n", offs + 4, - mmio_readl(ich_spibar + offs + 4), i); - } - ichspi_bbar = mmio_readl(ich_spibar + 0x50); - msg_pdbg("0x50: 0x%08x (BBAR)\n", - ichspi_bbar); - msg_pdbg("0x54: 0x%04x (PREOP)\n", - mmio_readw(ich_spibar + 0x54)); - msg_pdbg("0x56: 0x%04x (OPTYPE)\n", - mmio_readw(ich_spibar + 0x56)); - msg_pdbg("0x58: 0x%08x (OPMENU)\n", - mmio_readl(ich_spibar + 0x58)); - msg_pdbg("0x5c: 0x%08x (OPMENU+4)\n", - mmio_readl(ich_spibar + 0x5c)); - for (i = 0; i < 4; i++) { - int offs; - offs = 0x60 + (i * 4); - msg_pdbg("0x%02x: 0x%08x (PBR%d)\n", offs, - mmio_readl(ich_spibar + offs), i); - } - msg_pdbg("\n"); - if (mmio_readw(ich_spibar) & (1 << 15)) { - msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n"); - ichspi_lock = 1; - } - ich_init_opcodes(); - break; - case SPI_CONTROLLER_ICH9: - tmp2 = mmio_readw(ich_spibar + 4); - msg_pdbg("0x04: 0x%04x (HSFS)\n", tmp2); - msg_pdbg("FLOCKDN %i, ", (tmp2 >> 15 & 1)); - msg_pdbg("FDV %i, ", (tmp2 >> 14) & 1); - msg_pdbg("FDOPSS %i, ", (tmp2 >> 13) & 1); - msg_pdbg("SCIP %i, ", (tmp2 >> 5) & 1); - msg_pdbg("BERASE %i, ", (tmp2 >> 3) & 3); - msg_pdbg("AEL %i, ", (tmp2 >> 2) & 1); - msg_pdbg("FCERR %i, ", (tmp2 >> 1) & 1); - msg_pdbg("FDONE %i\n", (tmp2 >> 0) & 1); - - tmp = mmio_readl(ich_spibar + 0x50); - msg_pdbg("0x50: 0x%08x (FRAP)\n", tmp); - msg_pdbg("BMWAG 0x%02x, ", ICH_BMWAG(tmp)); - msg_pdbg("BMRAG 0x%02x, ", ICH_BMRAG(tmp)); - msg_pdbg("BRWA 0x%02x, ", ICH_BRWA(tmp)); - msg_pdbg("BRRA 0x%02x\n", ICH_BRRA(tmp)); - - /* print out the FREGx registers along with FRAP access bits */ - for(i = 0; i < 5; i++) - do_ich9_spi_frap(tmp, i); - - msg_pdbg("0x74: 0x%08x (PR0)\n", - mmio_readl(ich_spibar + 0x74)); - msg_pdbg("0x78: 0x%08x (PR1)\n", - mmio_readl(ich_spibar + 0x78)); - msg_pdbg("0x7C: 0x%08x (PR2)\n", - mmio_readl(ich_spibar + 0x7C)); - msg_pdbg("0x80: 0x%08x (PR3)\n", - mmio_readl(ich_spibar + 0x80)); - msg_pdbg("0x84: 0x%08x (PR4)\n", - mmio_readl(ich_spibar + 0x84)); - msg_pdbg("0x90: 0x%08x (SSFS, SSFC)\n", - mmio_readl(ich_spibar + 0x90)); - msg_pdbg("0x94: 0x%04x (PREOP)\n", - mmio_readw(ich_spibar + 0x94)); - msg_pdbg("0x96: 0x%04x (OPTYPE)\n", - mmio_readw(ich_spibar + 0x96)); - msg_pdbg("0x98: 0x%08x (OPMENU)\n", - mmio_readl(ich_spibar + 0x98)); - msg_pdbg("0x9C: 0x%08x (OPMENU+4)\n", - mmio_readl(ich_spibar + 0x9C)); - ichspi_bbar = mmio_readl(ich_spibar + 0xA0); - msg_pdbg("0xA0: 0x%08x (BBAR)\n", - ichspi_bbar); - msg_pdbg("0xB0: 0x%08x (FDOC)\n", - mmio_readl(ich_spibar + 0xB0)); - if (tmp2 & (1 << 15)) { - msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n"); - ichspi_lock = 1; - } - ich_init_opcodes(); - break; - default: - /* Nothing */ - break; - } - - old = pci_read_byte(dev, 0xdc); - msg_pdbg("SPI Read Configuration: "); - new = (old >> 2) & 0x3; - switch (new) { - case 0: - case 1: - case 2: - msg_pdbg("prefetching %sabled, caching %sabled, ", - (new & 0x2) ? "en" : "dis", - (new & 0x1) ? "dis" : "en"); - break; - default: - msg_pdbg("invalid prefetching/caching settings, "); - break; - } - + ich_init_spi(dev, tmp, rcrb, ich_generation); return ret; }
diff --git a/flash.h b/flash.h index c3302c4..a8ca6d7 100644 --- a/flash.h +++ b/flash.h @@ -680,10 +680,10 @@ int default_spi_send_multicommand(struct spi_command *cmds); uint32_t spi_get_valid_read_addr(void);
/* ichspi.c */ -extern int ichspi_lock; extern uint32_t ichspi_bbar; -extern void *ich_spibar; -int ich_init_opcodes(void); +void ich_init_spi(struct pci_dev *dev, uint32_t base, void * rcrb, + int ich_generation); +int via_init_spi(struct pci_dev * dev); int ich_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int ich_spi_read(struct flashchip *flash, uint8_t *buf, int start, int len); diff --git a/ichspi.c b/ichspi.c index d6f9118..246f3ae 100644 --- a/ichspi.c +++ b/ichspi.c @@ -101,11 +101,11 @@ #define ICH7_REG_OPMENU 0x58 /* 64 Bits */
/* ICH SPI configuration lock-down. May be set during chipset enabling. */ -int ichspi_lock = 0; +static int ichspi_lock = 0;
uint32_t ichspi_bbar = 0;
-void *ich_spibar = NULL; +static void *ich_spibar = NULL;
typedef struct _OPCODE { uint8_t opcode; //This commands spi opcode @@ -364,7 +364,7 @@ void ich_set_bbar(uint32_t minaddr) * * It should be called before ICH sends any spi command. */ -int ich_init_opcodes(void) +static int ich_init_opcodes(void) { int rc = 0; OPCODES *curopcodes_done; @@ -398,6 +398,214 @@ int ich_init_opcodes(void) } }
+#define ICH_BMWAG(x) ((x >> 24) & 0xff) +#define ICH_BMRAG(x) ((x >> 16) & 0xff) +#define ICH_BRWA(x) ((x >> 8) & 0xff) +#define ICH_BRRA(x) ((x >> 0) & 0xff) + +#define ICH_FREG_BASE(x) ((x >> 0) & 0x1fff) +#define ICH_FREG_LIMIT(x) ((x >> 16) & 0x1fff) + +static void do_ich9_spi_frap(uint32_t frap, int i) +{ + const char *access_names[4] = { + "locked", "read-only", "write-only", "read-write" + }; + const char *region_names[5] = { + "Flash Descriptor", "BIOS", "Management Engine", + "Gigabit Ethernet", "Platform Data" + }; + uint32_t base, limit; + int rwperms = (((ICH_BRWA(frap) >> i) & 1) << 1) | + (((ICH_BRRA(frap) >> i) & 1) << 0); + int offset = 0x54 + i * 4; + uint32_t freg = mmio_readl(ich_spibar + offset); + + msg_pdbg("0x%02X: 0x%08x (FREG%i: %s)\n", + offset, freg, i, region_names[i]); + + base = ICH_FREG_BASE(freg); + limit = ICH_FREG_LIMIT(freg); + if (base == 0x1fff && limit == 0) { + /* this FREG is disabled */ + msg_pdbg("%s region is unused.\n", region_names[i]); + return; + } + + msg_pdbg("0x%08x-0x%08x is %s\n", + (base << 12), (limit << 12) | 0x0fff, + access_names[rwperms]); +} + +void ich_init_spi(struct pci_dev *dev, uint32_t base, void * rcrb, + int ich_generation) +{ + int i; + uint8_t old, new; + uint16_t spibar_offset, tmp2; + uint32_t tmp; + + switch (ich_generation) { + case 7: + buses_supported = CHIP_BUSTYPE_SPI; + spi_controller = SPI_CONTROLLER_ICH7; + spibar_offset = 0x3020; + break; + case 8: + buses_supported = CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; + spi_controller = SPI_CONTROLLER_ICH9; + spibar_offset = 0x3020; + break; + case 9: + case 10: + default: /* Future version might behave the same */ + buses_supported = CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; + spi_controller = SPI_CONTROLLER_ICH9; + spibar_offset = 0x3800; + break; + } + + /* SPIBAR is at RCRB+0x3020 for ICH[78] and RCRB+0x3800 for ICH9. */ + msg_pdbg("SPIBAR = 0x%x + 0x%04x\n", base, spibar_offset); + + /* Assign Virtual Address */ + ich_spibar = rcrb + spibar_offset; + + switch (spi_controller) { + case SPI_CONTROLLER_ICH7: + msg_pdbg("0x00: 0x%04x (SPIS)\n", + mmio_readw(ich_spibar + 0)); + msg_pdbg("0x02: 0x%04x (SPIC)\n", + mmio_readw(ich_spibar + 2)); + msg_pdbg("0x04: 0x%08x (SPIA)\n", + mmio_readl(ich_spibar + 4)); + for (i = 0; i < 8; i++) { + int offs; + offs = 8 + (i * 8); + msg_pdbg("0x%02x: 0x%08x (SPID%d)\n", offs, + mmio_readl(ich_spibar + offs), i); + msg_pdbg("0x%02x: 0x%08x (SPID%d+4)\n", offs + 4, + mmio_readl(ich_spibar + offs + 4), i); + } + ichspi_bbar = mmio_readl(ich_spibar + 0x50); + msg_pdbg("0x50: 0x%08x (BBAR)\n", + ichspi_bbar); + msg_pdbg("0x54: 0x%04x (PREOP)\n", + mmio_readw(ich_spibar + 0x54)); + msg_pdbg("0x56: 0x%04x (OPTYPE)\n", + mmio_readw(ich_spibar + 0x56)); + msg_pdbg("0x58: 0x%08x (OPMENU)\n", + mmio_readl(ich_spibar + 0x58)); + msg_pdbg("0x5c: 0x%08x (OPMENU+4)\n", + mmio_readl(ich_spibar + 0x5c)); + for (i = 0; i < 4; i++) { + int offs; + offs = 0x60 + (i * 4); + msg_pdbg("0x%02x: 0x%08x (PBR%d)\n", offs, + mmio_readl(ich_spibar + offs), i); + } + msg_pdbg("\n"); + if (mmio_readw(ich_spibar) & (1 << 15)) { + msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n"); + ichspi_lock = 1; + } + ich_init_opcodes(); + break; + case SPI_CONTROLLER_ICH9: + tmp2 = mmio_readw(ich_spibar + 4); + msg_pdbg("0x04: 0x%04x (HSFS)\n", tmp2); + msg_pdbg("FLOCKDN %i, ", (tmp2 >> 15 & 1)); + msg_pdbg("FDV %i, ", (tmp2 >> 14) & 1); + msg_pdbg("FDOPSS %i, ", (tmp2 >> 13) & 1); + msg_pdbg("SCIP %i, ", (tmp2 >> 5) & 1); + msg_pdbg("BERASE %i, ", (tmp2 >> 3) & 3); + msg_pdbg("AEL %i, ", (tmp2 >> 2) & 1); + msg_pdbg("FCERR %i, ", (tmp2 >> 1) & 1); + msg_pdbg("FDONE %i\n", (tmp2 >> 0) & 1); + + tmp = mmio_readl(ich_spibar + 0x50); + msg_pdbg("0x50: 0x%08x (FRAP)\n", tmp); + msg_pdbg("BMWAG 0x%02x, ", ICH_BMWAG(tmp)); + msg_pdbg("BMRAG 0x%02x, ", ICH_BMRAG(tmp)); + msg_pdbg("BRWA 0x%02x, ", ICH_BRWA(tmp)); + msg_pdbg("BRRA 0x%02x\n", ICH_BRRA(tmp)); + + /* print out the FREGx registers along with FRAP access bits */ + for(i = 0; i < 5; i++) + do_ich9_spi_frap(tmp, i); + + msg_pdbg("0x74: 0x%08x (PR0)\n", + mmio_readl(ich_spibar + 0x74)); + msg_pdbg("0x78: 0x%08x (PR1)\n", + mmio_readl(ich_spibar + 0x78)); + msg_pdbg("0x7C: 0x%08x (PR2)\n", + mmio_readl(ich_spibar + 0x7C)); + msg_pdbg("0x80: 0x%08x (PR3)\n", + mmio_readl(ich_spibar + 0x80)); + msg_pdbg("0x84: 0x%08x (PR4)\n", + mmio_readl(ich_spibar + 0x84)); + msg_pdbg("0x90: 0x%08x (SSFS, SSFC)\n", + mmio_readl(ich_spibar + 0x90)); + msg_pdbg("0x94: 0x%04x (PREOP)\n", + mmio_readw(ich_spibar + 0x94)); + msg_pdbg("0x96: 0x%04x (OPTYPE)\n", + mmio_readw(ich_spibar + 0x96)); + msg_pdbg("0x98: 0x%08x (OPMENU)\n", + mmio_readl(ich_spibar + 0x98)); + msg_pdbg("0x9C: 0x%08x (OPMENU+4)\n", + mmio_readl(ich_spibar + 0x9C)); + ichspi_bbar = mmio_readl(ich_spibar + 0xA0); + msg_pdbg("0xA0: 0x%08x (BBAR)\n", + ichspi_bbar); + msg_pdbg("0xB0: 0x%08x (FDOC)\n", + mmio_readl(ich_spibar + 0xB0)); + if (tmp2 & (1 << 15)) { + msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n"); + ichspi_lock = 1; + } + ich_init_opcodes(); + break; + default: + /* Nothing */ + break; + } + + old = pci_read_byte(dev, 0xdc); + msg_pdbg("SPI Read Configuration: "); + new = (old >> 2) & 0x3; + switch (new) { + case 0: + case 1: + case 2: + msg_pdbg("prefetching %sabled, caching %sabled, ", + (new & 0x2) ? "en" : "dis", + (new & 0x1) ? "dis" : "en"); + break; + default: + msg_pdbg("invalid prefetching/caching settings, "); + break; + } +} + +int via_init_spi(struct pci_dev * dev) +{ + uint32_t mmio_base; + + mmio_base = (pci_read_long(dev, 0xbc)) << 8; + msg_pdbg("MMIO base at = 0x%x\n", mmio_base); + ich_spibar = physmap("VT8237S MMIO registers", mmio_base, 0x70); + + msg_pdbg("0x6c: 0x%04x (CLOCK/DEBUG)\n", + mmio_readw(ich_spibar + 0x6c)); + + /* Not sure if it speaks all these bus protocols. */ + buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; + spi_controller = SPI_CONTROLLER_VIA; + ich_init_opcodes(); + + return 0; +} + static int ich7_run_opcode(OPCODE op, uint32_t offset, uint8_t datalength, uint8_t * data, int maxdata) {