Author: uwe Date: Fri Sep 3 20:21:21 2010 New Revision: 1151 URL: http://flashrom.org/trac/flashrom/changeset/1151
Log: Add Intel Gigabit NIC SPI flashing support. Tested on a 82541PI (0x8086, 0x107c) using 32-bit hardware.
The last line in nicintel_request_spibus() could be changed so that FL_BUSY is used instead.
Shortened sample log: [...] Found "Intel 82541PI Gigabit Ethernet Controller" (8086:107c, BDF 01:03.0). Found chip "ST M25P10.RES" (128 KB, SPI) at physical address 0xfffe0000. Multiple flash chips were detected: M25P05.RES M25P10.RES Please specify which chip to use with the -c <chipname> option. [...]
Signed-off-by: Idwer Vollering vidwer@gmail.com Acked-by: Uwe Hermann uwe@hermann-uwe.de
Added: trunk/nicintel_spi.c Modified: trunk/Makefile trunk/flashrom.8 trunk/flashrom.c trunk/print.c trunk/print_wiki.c trunk/programmer.h trunk/spi.c
Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/Makefile Fri Sep 3 20:21:21 2010 (r1151) @@ -121,9 +121,13 @@ ifeq ($(CONFIG_INTERNAL), yes) override CONFIG_BITBANG_SPI = yes else +ifeq ($(CONFIG_NICINTEL_SPI), yes) +override CONFIG_BITBANG_SPI = yes +else CONFIG_BITBANG_SPI ?= no endif endif +endif
# Always enable 3Com NICs for now. CONFIG_NIC3COM ?= yes @@ -153,6 +157,9 @@ # Disable National Semiconductor NICs until support is complete and tested. CONFIG_NICNATSEMI ?= no
+# Always enable SPI on Intel NICs for now. +CONFIG_NICINTEL_SPI ?= yes + # Always enable Bus Pirate SPI for now. CONFIG_BUSPIRATE_SPI ?= yes
@@ -244,6 +251,12 @@ NEED_PCI := yes endif
+ifeq ($(CONFIG_NICINTEL_SPI), yes) +FEATURE_CFLAGS += -D'CONFIG_NICINTEL_SPI=1' +PROGRAMMER_OBJS += nicintel_spi.o +NEED_PCI := yes +endif + ifeq ($(CONFIG_BUSPIRATE_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BUSPIRATE_SPI=1' PROGRAMMER_OBJS += buspirate_spi.o
Modified: trunk/flashrom.8 ============================================================================== --- trunk/flashrom.8 Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/flashrom.8 Fri Sep 3 20:21:21 2010 (r1151) @@ -190,6 +190,9 @@ .BR "* rayer_spi" " (for SPI flash ROMs attached to a RayeR parport \ based programmer)" .sp +.BR "* nicintel_spi" " (for SPI flash ROMs attached to an Intel Gigabit \ +network cards)" +.sp Some programmers have optional or mandatory parameters which are described in detail in the .B PROGRAMMER SPECIFIC INFO
Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/flashrom.c Fri Sep 3 20:21:21 2010 (r1151) @@ -49,7 +49,7 @@ * if more than one of them is selected. If only one is selected, it is clear * that the user wants that one to become the default. */ -#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_FT2232_SPI+CONFIG_SERPROG+CONFIG_BUSPIRATE_SPI+CONFIG_DEDIPROG+CONFIG_RAYER_SPI > 1 +#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_FT2232_SPI+CONFIG_SERPROG+CONFIG_BUSPIRATE_SPI+CONFIG_DEDIPROG+CONFIG_RAYER_SPI+CONFIG_NICINTEL_SPI > 1 #error Please enable either CONFIG_DUMMY or CONFIG_INTERNAL or disable support for all programmers except one. #endif enum programmer programmer = @@ -90,6 +90,9 @@ #if CONFIG_RAYER_SPI == 1 PROGRAMMER_RAYER_SPI #endif +#if CONFIG_NICINTEL_SPI == 1 + PROGRAMMER_NICINTEL_SPI +#endif ; #endif
@@ -414,6 +417,25 @@ }, #endif
+#if CONFIG_NICINTEL_SPI == 1 + { + .name = "nicintel_spi", + .init = nicintel_spi_init, + .shutdown = nicintel_spi_shutdown, + .map_flash_region = fallback_map, + .unmap_flash_region = fallback_unmap, + .chip_readb = noop_chip_readb, + .chip_readw = fallback_chip_readw, + .chip_readl = fallback_chip_readl, + .chip_readn = fallback_chip_readn, + .chip_writeb = noop_chip_writeb, + .chip_writew = fallback_chip_writew, + .chip_writel = fallback_chip_writel, + .chip_writen = fallback_chip_writen, + .delay = internal_delay, + }, +#endif + {}, /* This entry corresponds to PROGRAMMER_INVALID. */ };
Added: trunk/nicintel_spi.c ============================================================================== --- /dev/null 00:00:00 1970 (empty, because file is newly added) +++ trunk/nicintel_spi.c Fri Sep 3 20:21:21 2010 (r1151) @@ -0,0 +1,187 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2010 Carl-Daniel Hailfinger + * Copyright (C) 2010 Idwer Vollering + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* + * Datasheet: + * PCI/PCI-X Family of Gigabit Ethernet Controllers Software Developer's Manual + * 82540EP/EM, 82541xx, 82544GC/EI, 82545GM/EM, 82546GB/EB, and 82547xx + * http://download.intel.com/design/network/manuals/8254x_GBe_SDM.pdf + */ + +#include <stdlib.h> +#include "flash.h" +#include "programmer.h" + +#define PCI_VENDOR_ID_INTEL 0x8086 + +#define EECD 0x10 +#define FLA 0x1c + +/* + * Register bits of EECD. + * + * Bit 04, 05: FWE (Flash Write Enable Control) + * 00b = not allowed + * 01b = flash writes disabled + * 10b = flash writes enabled + * 11b = not allowed + */ +#define FLASH_WRITES_DISABLED 0x10 /* FWE: 10000b */ +#define FLASH_WRITES_ENABLED 0x20 /* FWE: 100000b */ + +/* Flash Access register bits */ +/* Table 13-9 */ +#define FL_SCK 0 +#define FL_CS 1 +#define FL_SI 2 +#define FL_SO 3 +#define FL_REQ 4 +#define FL_GNT 5 +/* Currently unused */ +// #define FL_BUSY 30 +// #define FL_ER 31 + +uint8_t *nicintel_spibar; + +const struct pcidev_status nics_intel_spi[] = { + {PCI_VENDOR_ID_INTEL, 0x107c, OK, "Intel", "82541PI Gigabit Ethernet Controller"}, + + {}, +}; + +static void nicintel_request_spibus(void) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp |= 1 << FL_REQ; + pci_mmio_writel(tmp, nicintel_spibar + FLA); + + /* Wait until we are allowed to use the SPI bus. */ + while (!(pci_mmio_readl(nicintel_spibar + FLA) & (1 << FL_GNT))) ; +} + +static void nicintel_release_spibus(void) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp &= ~(1 << FL_REQ); + pci_mmio_writel(tmp, nicintel_spibar + FLA); +} + +static void nicintel_bitbang_set_cs(int val) +{ + uint32_t tmp; + + /* + * Requesting and releasing the SPI bus is handled in here to allow + * the chipset to use its own SPI engine for native reads. + */ + if (val == 0) + nicintel_request_spibus(); + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp &= ~(1 << FL_CS); + tmp |= (val << FL_CS); + pci_mmio_writel(tmp, nicintel_spibar + FLA); + + if (val == 1) + nicintel_release_spibus(); +} + +static void nicintel_bitbang_set_sck(int val) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp &= ~(1 << FL_SCK); + tmp |= (val << FL_SCK); + pci_mmio_writel(tmp, nicintel_spibar + FLA); +} + +static void nicintel_bitbang_set_mosi(int val) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp &= ~(1 << FL_SI); + tmp |= (val << FL_SI); + pci_mmio_writel(tmp, nicintel_spibar + FLA); +} + +static int nicintel_bitbang_get_miso(void) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + FLA); + tmp = (tmp >> FL_SO) & 0x1; + return tmp; +} + +static const struct bitbang_spi_master bitbang_spi_master_nicintel = { + .type = BITBANG_SPI_MASTER_NICINTEL, + .set_cs = nicintel_bitbang_set_cs, + .set_sck = nicintel_bitbang_set_sck, + .set_mosi = nicintel_bitbang_set_mosi, + .get_miso = nicintel_bitbang_get_miso, +}; + +int nicintel_spi_init(void) +{ + uint32_t tmp; + + get_io_perms(); + + io_base_addr = pcidev_init(PCI_VENDOR_ID_INTEL, PCI_BASE_ADDRESS_0, + nics_intel_spi); + + nicintel_spibar = physmap("Intel Gigabit NIC w/ SPI flash", + io_base_addr, 4096); + tmp = pci_mmio_readl(nicintel_spibar + EECD); + tmp &= ~FLASH_WRITES_DISABLED; + tmp |= FLASH_WRITES_ENABLED; + pci_mmio_writel(tmp, nicintel_spibar + EECD); + + /* 1 usec halfperiod delay for now. */ + if (bitbang_spi_init(&bitbang_spi_master_nicintel, 1)) + return 1; + + buses_supported = CHIP_BUSTYPE_SPI; + spi_controller = SPI_CONTROLLER_NICINTEL; + + return 0; +} + +int nicintel_spi_shutdown(void) +{ + uint32_t tmp; + + tmp = pci_mmio_readl(nicintel_spibar + EECD); + tmp &= ~FLASH_WRITES_ENABLED; + tmp |= FLASH_WRITES_DISABLED; + pci_mmio_writel(tmp, nicintel_spibar + EECD); + + physunmap(nicintel_spibar, 4096); + pci_cleanup(pacc); + release_io_perms(); + + return 0; +}
Modified: trunk/print.c ============================================================================== --- trunk/print.c Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/print.c Fri Sep 3 20:21:21 2010 (r1151) @@ -255,6 +255,9 @@ #if CONFIG_ATAHPT == 1 print_supported_pcidevs(ata_hpt); #endif +#if CONFIG_NICINTEL_SPI == 1 + print_supported_pcidevs(nics_intel_spi); +#endif
#if CONFIG_FT2232_SPI+CONFIG_DEDIPROG >= 1 printf("\nSupported USB devices flashrom can use "
Modified: trunk/print_wiki.c ============================================================================== --- trunk/print_wiki.c Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/print_wiki.c Fri Sep 3 20:21:21 2010 (r1151) @@ -296,6 +296,9 @@ #if CONFIG_ATAHPT == 1 print_supported_pcidevs_wiki(ata_hpt); #endif +#if CONFIG_NICINTEL_SPI == 1 + print_supported_pcidevs_wiki(nics_intel_spi); +#endif printf("\n|}\n"); }
Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/programmer.h Fri Sep 3 20:21:21 2010 (r1151) @@ -37,10 +37,10 @@ #if CONFIG_NICREALTEK == 1 PROGRAMMER_NICREALTEK, PROGRAMMER_NICREALTEK2, -#endif +#endif #if CONFIG_NICNATSEMI == 1 PROGRAMMER_NICNATSEMI, -#endif +#endif #if CONFIG_GFXNVIDIA == 1 PROGRAMMER_GFXNVIDIA, #endif @@ -73,6 +73,9 @@ #if CONFIG_RAYER_SPI == 1 PROGRAMMER_RAYER_SPI, #endif +#if CONFIG_NICINTEL_SPI == 1 + PROGRAMMER_NICINTEL_SPI, +#endif PROGRAMMER_INVALID /* This must always be the last entry. */ };
@@ -110,6 +113,9 @@ #if CONFIG_RAYER_SPI == 1 BITBANG_SPI_MASTER_RAYER, #endif +#if CONFIG_NICINTEL_SPI == 1 + BITBANG_SPI_MASTER_NICINTEL, +#endif #if CONFIG_INTERNAL == 1 #if defined(__i386__) || defined(__x86_64__) BITBANG_SPI_MASTER_MCP, @@ -207,7 +213,7 @@ #endif
/* print.c */ -#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT >= 1 +#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_NICINTEL_SPI >= 1 void print_supported_pcidevs(const struct pcidev_status *devs); #endif
@@ -378,6 +384,16 @@ extern const struct pcidev_status nics_natsemi[]; #endif
+/* nicintel_spi.c */ +#if CONFIG_NICINTEL_SPI == 1 +int nicintel_spi_init(void); +int nicintel_spi_shutdown(void); +int nicintel_spi_send_command(unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); +void nicintel_spi_chip_writeb(uint8_t val, chipaddr addr); +extern const struct pcidev_status nics_intel_spi[]; +#endif + /* satasii.c */ #if CONFIG_SATASII == 1 int satasii_init(void); @@ -494,6 +510,9 @@ #if CONFIG_RAYER_SPI == 1 SPI_CONTROLLER_RAYER, #endif +#if CONFIG_NICINTEL_SPI == 1 + SPI_CONTROLLER_NICINTEL, +#endif SPI_CONTROLLER_INVALID /* This must always be the last entry. */ }; extern const int spi_programmer_count;
Modified: trunk/spi.c ============================================================================== --- trunk/spi.c Fri Sep 3 05:35:48 2010 (r1150) +++ trunk/spi.c Fri Sep 3 20:21:21 2010 (r1151) @@ -136,6 +136,15 @@ }, #endif
+#if CONFIG_NICINTEL_SPI == 1 + { /* SPI_CONTROLLER_NICINTEL */ + .command = bitbang_spi_send_command, + .multicommand = default_spi_send_multicommand, + .read = bitbang_spi_read, + .write_256 = bitbang_spi_write_256, + }, +#endif + {}, /* This entry corresponds to SPI_CONTROLLER_INVALID. */ };
-
repository service