Forwarding. Please "reply to all".
---------- Forwarded message ----------
From: Nabs ch12011-7@yahoo.com.au
Date: 2012/12/5
Subject: Re: [flashrom] BPv3.6 w flashrom
To: "vidwer@gmail.com" vidwer@gmail.com
Just had a Eureka moment.
I think what confused me was the fact that the cables were soldered onto
the actual soic clip!
So all I need to do is desolder and resolder them into their correct
layouts, or desolder and use alligator clips instead?
Is that right? Cheers, Nabs.
------------------------------
* From: * Idwer Vollering vidwer@gmail.com;
* To: * Nabs ch12011-7@yahoo.com.au;
* Cc: * flashrom@flashrom.org flashrom@flashrom.org;
* Subject: * Re: [flashrom] BPv3.6 w flashrom
* Sent: * Wed, Dec 5, 2012 12:05:04 PM
2012/12/5 Nabs ch12011-7@yahoo.com.au:
Hi, sorry for the trouble. I'm running bus piratev3.6, bootloaderv4.4,
firmwarev6.1 on flashrom-0.9.6.1, i plan to run the BP at 1M.
When i run the command "flashrom -p buspirate_spi:dev=/dev/ttyUSB0 -Vr
oldbios.bin"
I get:
"
Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI) on
buspirate_spi.
Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1
0x0,
id2 0x0
Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI).
===
This flash part has status NOT WORKING for operations: PROBE READ ERASE
WRITE
" etc...
I think i have the wiring wrong which is why i get that error, i wonder if
you could help me as its my first time?
I'm trying to use In-circuit programming with a soldered bios chip using
an
'SOIC 8 clip' and it has 8 wires. But the bus pirate has 10 pins.
From another thread, these are the connections i need:
Bus Pirate "MISO" (Pin 1) <----- SPI Device "DO" (Wire/Pin 2)
Bus Pirate "CS" (Pin 2) -----> SPI Device "CS" (Wire/Pin 1)
Bus Pirate "MOSI" (Pin 3) -----> SPI Device "DI" (Wire/Pin 5)
Bus Pirate "CLK" (Pin 4) -----> SPI Device "CLK" (Wire/Pin 6)
Bus Pirate "GND" (Pin 10) <----> SPI Device "GND" (Wire/Pin 4)
It appears to me that GND is pin 10 and that the wires of the SOIC8 clip
only contact pins 1-8, so how can this work?
Also, could i just check the layout of the pins on the bus pirate if i'm
reading it correctly on BPv3.6:
10 9
8 7
6 5
4 3
2 1
Corresponding to:
GND 3V3
+5V ADC
VPU AUX
CLK MOSI
CS MISO
Forget the existence of +5V, VPU, ADC and AUX for now (
http://dangerousprototypes.com/docs/Bus_Pirate_I/O_Pin_Descriptions ),
connect the clip to the buspirate so that the clip passes the
buspirate pins like mentioned in this post:
http://www.coreboot.org/pipermail/flashrom/2012-November/010178.html
This works for me, with a MX25L1605A soic8 chip:
CS# (CS) [1 chip 8] VCC
(bridge with buspirate pin 3+7)
SO (MISO) [2 chip 7] HOLD#
(+3V3)
WP# (bridge with buspirate pin 7+8) [3 chip 6] SCLK (CLK)
GND (GND) [4 chip 5] SI (MOSI)
Or are the pin numbers read in the opposite direction?
ie
9 10
7 8
5 6
3 4
1 2
Here's an image of my bus pirate if it helps:
http://dangerousprototypes.com/wp-content/media/2012/11/Bus-Pirate-v3.6inter...
Your help is much appreciated and i appreciate your patience, Nabs.
flashrom mailing list
flashrom@flashrom.org
http://www.flashrom.org/mailman/listinfo/flashrom