[commit] r1339 - trunk

[repository service]

Author: stefanct
Date: Thu Jun 16 01:44:52 2011
New Revision: 1339
URL: http://flashrom.org/trac/flashrom/changeset/1339

Log:
Update the flashrom manpage

- Add missing entries for nicintel and satamv.
 - Add various programmers to those that support the 'pci=' option.
 - Small cosmetic, whitespace, grammar or consistency fixes.
 - Update the date of last change of the manpage.
 - Add Stefan Tauner to the list of authors.

Signed-off-by: Uwe Hermann 
Signed-off-by: Andrew Morgan 
Signed-off-by: Stefan Tauner 
Acked-by: Uwe Hermann

Modified:
   trunk/flashrom.8

Modified: trunk/flashrom.8
==============================================================================
--- trunk/flashrom.8	Tue Jun 14 03:35:36 2011	(r1338)
+++ trunk/flashrom.8	Thu Jun 16 01:44:52 2011	(r1339)
@@ -1,4 +1,4 @@
-.TH FLASHROM 8 "Jun 06, 2010"
+.TH FLASHROM 8 "Jun 14, 2011"
 .SH NAME
 flashrom - detect, read, write, verify and erase flash chips
 .SH SYNOPSIS
@@ -172,12 +172,17 @@
 .BR "* nicnatsemi" " (for flash ROMs on National Semiconductor DP838* network \
 cards)"
 .sp
+.BR "* nicintel" " (for parallel flash ROMs attached to Intel 10/100Mbit \
+network cards)
+.sp
 .BR "* gfxnvidia" " (for flash ROMs on NVIDIA graphics cards)"
 .sp
 .BR "* drkaiser" " (for flash ROMs on Dr. Kaiser PC-Waechter PCI cards)"
 .sp
 .BR "* satasii" " (for flash ROMs on Silicon Image SATA/IDE controllers)"
 .sp
+.BR "* satamv" " (for flash ROMs on Marvell SATA controllers)"
+.sp
 .BR "* atahpt" " (for flash ROMs on Highpoint ATA/RAID controllers)"
 .sp
 .BR "* it87spi" " (for flash ROMs behind an ITE IT87xx Super I/O LPC/SPI \
@@ -313,7 +318,7 @@
 .B "flashrom -p dummy:bus=[type[+type[+type]]]"
 syntax where
 .B type
-can be any of
+can be
 .BR parallel ", " lpc ", " fwh ", " spi
 in any order. If you specify bus without type, all buses will be disabled.
 If you do not specify bus, all buses will be enabled.
@@ -321,8 +326,9 @@
 Example:
 .B "flashrom -p dummy:bus=lpc+fwh"
 .TP
-.BR "nic3com" , " nicrealtek" , " nicsmc1211" , " nicnatsemi" , " gfxnvidia\
-" , " satasii " and " atahpt " programmers
+.BR "nic3com" , " nicrealtek" , " nicsmc1211" , " nicnatsemi" , " nicintel\
+" , " nicintel_spi" , " gfxnvidia" , " ogp_spi" , " drkaiser" , " satasii\
+" , " satamv" ", and " atahpt " programmers
 These programmers have an option to specify the PCI address of the card
 your want to use, which must be specified if more than one card supported
 by the selected programmer is installed in your system. The syntax is
@@ -361,12 +367,12 @@
 .sp
 syntax where
 .B model
-can be one of
+can be
 .BR 2232H ", " 4232H ", " jtagkey ", " openmoko ", " arm-usb-tiny ", " \
 arm-usb-tiny-h ", " arm-usb-ocd " or " arm-usb-ocd-h
 and
 .B interface
-can be any of
+can be
 .BR A ", or " B .
 The default model is
 .B 4232H
@@ -397,12 +403,12 @@
 parameter specifies the frequency of the SPI bus. The parameter
 delimiter is a comma. Syntax is
 .sp
-.B "flashrom -p buspirate_spi:dev=/dev/device,spispeed=frequency"
+.B "  flashrom -p buspirate_spi:dev=/dev/device,spispeed=frequency"
 .sp
 where
 .B frequency
-can be any of
-.BR 30k ", " 125k ", " 250k ", " 1M ", " 2M ", " 2.6M ", " 4M ", " 8M
+can be
+.BR 30k ", " 125k ", " 250k ", " 1M ", " 2M ", " 2.6M ", " 4M " or " 8M
 (in Hz). The default is the maximum frequency of 8 MHz.
 .TP
 .BR "dediprog " programmer
@@ -413,11 +419,11 @@
 .BR mV ", " milliVolt ", " V " or " Volt
 as unit specifier. Syntax is
 .sp
-.B "flashrom -p dediprog:voltage=value"
+.B "  flashrom -p dediprog:voltage=value"
 .sp
 where
 .B value
-can be any of
+can be
 .BR 0V ", " 1.8V ", " 2.5V ", " 3.5V
 or the equivalent in mV.
 .TP
@@ -438,7 +444,7 @@
 http://rayer.ic.cz/elektro/spipgm.htm
 .TP
 .BR "ogp_spi " programmer
-The FLASH ROM chip to access must be specified with the 
+The flash ROM chip to access must be specified with the 
 .B rom
 parameter.
 .sp
@@ -454,7 +460,7 @@
 .B bprom
 or
 .B bios
-for the BIOS ROM.  If more than one card supported by the ogp_spi programmer
+for the BIOS ROM. If more than one card supported by the ogp_spi programmer
 is installed in your system, you have to specify the PCI address of the card
 you want to use with the
 .B pci=
@@ -599,6 +605,8 @@
 .br
 Stefan Reinauer
 .br
+Stefan Tauner
+.br
 Stefan Wildemann
 .br
 Stephan Guilloux
@@ -613,7 +621,7 @@
 .br
 some others, please see the flashrom svn changelog for details.
 .br
-All authors can be reached via e-mail at .
+All authors can be reached via email at .
 .PP
 This manual page was written by Uwe Hermann 
 and Carl-Daniel Hailfinger.