carldani,
The bios version I am currently using (2.6.2) is no longer available for download, but i happen to have a copy of it attached (raw ROM file). Below is the rest of the info. you asked for.
ubuntu@ubuntu:~/flashrom$ sudo ./flashrom -r backup.bin flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... WARNING: SPI Configuration Lockdown activated. FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... OK. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Reading flash... done. ubuntu@ubuntu:~/flashrom$ hexdump backup.bin 0000000 0000 0000 0000 0000 0000 0000 0000 0000 * 0100000 ubuntu@ubuntu:~/flashrom$
dmidecode snippet (bonus!)
Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Dell Inc. Version: 2.6.2 Release Date: 08/12/2008 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 1024 kB Characteristics: PCI is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed Boot from CD is supported Selectable boot is supported EDD is supported Japanese floppy for Toshiba 1.2 MB is supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) ACPI is supported USB legacy is supported LS-120 boot is supported BIOS boot specification is supported Function key-initiated network boot is supported Targeted content distribution is supported BIOS Revision: 2.6
flashrom -V
flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 tried to set 0xdc to 0x3 on ICH8/ICH8R failed (WARNING ONLY)
Root Complex Register Block address = 0xfeda8000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfeda8000 + 0x3020 0x04: 0xa000 (HSFS) FLOCKDN 1, FDV 0, FDOPSS 1, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0 0x50: 0x00000202 (FRAP) BMWAG 0, BMRAG 0, BRWA 2, BRRA 2 0x54: 0x00001fff (FREG0) 0x58: 0x00001fff (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00001fff (FREG3) 0x64: 0x00000000 (FREG4) 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00422004 (SSFS, SSFC) 0x94: 0x0606 (PREOP) 0x96: 0x4fc8 (OPTYPE) 0x98: 0x029fabab (OPMENU) 0x9C: 0x010502d8 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) WARNING: SPI Configuration Lockdown activated. Generating OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 512M loops per second, 100 myus = 200 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L40P, 512 KB: RDID returned 0xc2 0x20 0x14 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x01, id2 0x0b Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xda, id2 0x00 Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_49lfxxxc: id1 0xda, id2 0x00 Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: Invalid OPCODE 0x90 Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040B.REMS, 512 KB: Invalid OPCODE 0x90 Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x01, id2 0x0b Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xda, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xda, id2 0x00 Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x01, id2 0x0b Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xda, id2 0x00 Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C011, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49F002U, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x01, id2 0x0b, id1 is normal flash content, id2 is normal flash content Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. Invalid OPCODE 0x90 Not unmapping zero size at (nil) === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === No operations were specified.
lspci -nnvvvxxx
00:00.0 Host bridge [0600]: Intel Corporation 82Q963/Q965 Memory Controller Hub [8086:2990] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: intel-agp 00: 86 80 90 29 06 01 90 20 02 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 50 da fe 00 00 00 00 00 00 da fe 00 00 00 00 50: 00 00 02 00 03 00 00 00 00 00 00 00 00 00 00 00 60: 01 00 00 e0 00 00 00 00 01 40 da fe 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 11 01 00 00 00 00 40 00 4b 00 00 1a 79 00 a0: 40 00 00 13 00 00 00 d0 00 00 00 00 00 00 f0 cf b0: 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 49 00 00 00 01 00 01 13 e0: 09 00 09 51 6e 03 00 48 06 8c 00 00 00 00 00 00 f0: 02 00 00 00 00 00 00 00 90 0f 04 00 00 00 00 00
00:01.0 PCI bridge [0604]: Intel Corporation 82Q963/Q965 PCI Express Root Port [8086:2991] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-feafffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: Dell Device [1028:01da] Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 4151 Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 1, PowerLimit 25.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [140] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 91 29 07 05 10 00 02 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 d0 d0 00 00 20: 00 fa a0 fe 01 d0 f1 df 00 00 00 00 00 00 00 00 30: 00 00 00 00 88 00 00 00 00 00 00 00 0b 01 0a 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 da 01 90: 05 a0 01 00 0c 30 e0 fe 51 41 00 00 00 00 00 00 a0: 10 00 41 01 00 80 00 00 00 00 00 00 01 25 01 02 b0: 40 00 01 11 80 0c 0c 00 c0 01 48 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 f0: 00 00 01 00 03 e1 3f 00 90 0f 04 00 00 00 00 00
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at ff20 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 34 28 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 21 ff 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at ff00 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 35 28 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 ff 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20) Subsystem: Dell Device [1028:01da] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 0: Memory at febfbc00 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00: 86 80 3a 28 06 01 90 02 02 20 03 0c 00 00 00 00 10: 00 bc bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 50 00 00 00 00 00 00 00 09 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 01 00 00 00 00 01 00 00 01 00 00 08 80 70: 00 00 c7 03 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 88 85 40 00 86 0f 03 00 06 97 02 20
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00: 86 80 4b 28 06 01 10 00 02 00 03 04 10 00 00 00 10: 04 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00 40: 01 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 00 91 00 00 00 00 00 00 08 10 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: f9f00000-f9ffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 4, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 4159 Capabilities: [90] Subsystem: Dell Device [1028:01da] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 3f 28 07 05 10 00 02 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 f0 00 00 00 20: f0 f9 f0 f9 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 02 00 40: 10 80 41 01 c0 8f 00 00 00 00 10 00 11 24 11 01 50: 40 00 11 30 60 05 20 00 00 00 48 01 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 01 00 0c 30 e0 fe 59 41 00 00 00 00 00 00 90: 0d a0 00 00 28 10 da 01 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 11 08 00 00 00 00 e0: 00 00 c7 00 06 07 08 00 30 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: f9e00000-f9efffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 0, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 4161 Capabilities: [90] Subsystem: Dell Device [1028:01da] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00: 86 80 47 28 07 05 10 00 02 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 f0 00 00 00 20: e0 f9 e0 f9 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 02 00 40: 10 80 41 01 c0 8f 00 00 00 00 10 00 11 24 11 05 50: 40 00 11 30 60 05 00 00 00 00 48 01 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 01 00 0c 30 e0 fe 61 41 00 00 00 00 00 00 90: 0d a0 00 00 28 10 da 01 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 11 08 00 00 00 00 e0: 00 00 c7 00 06 07 08 00 30 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at ff80 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 30 28 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 ff 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at ff60 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 31 28 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 61 ff 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at ff40 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 32 28 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 41 ff 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20) Subsystem: Dell Device [1028:01da] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at ff980800 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00: 86 80 36 28 06 01 90 02 02 20 03 0c 00 00 00 00 10: 00 08 98 ff 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 01 00 00 00 00 01 00 00 01 00 00 08 80 70: 00 00 c7 3f 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 88 85 40 00 86 0f 03 00 06 97 02 20
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: f9c00000-f9dfffff Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Dell Device [1028:01da] 00: 86 80 4e 24 07 01 10 00 f2 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 04 04 20 c0 c0 80 22 20: c0 f9 d0 f9 01 f0 01 f0 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 00 00 02 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 50: 0d 00 00 00 28 10 da 01 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller [8086:2810] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00: 86 80 10 28 07 01 10 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 08 00 00 80 00 00 00 81 08 00 00 10 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 8b 8a 83 80 d0 00 00 00 89 80 89 85 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 0d 14 01 0c 7c 00 e1 00 04 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 10 06 00 00 38 00 00 00 13 00 00 00 00 03 00 00 b0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 33 22 11 00 67 45 00 00 00 c0 00 00 02 00 00 00 e0: 09 00 0c 10 21 00 04 ca 60 00 00 00 00 00 00 00 f0: 01 80 da fe 09 c1 23 00 86 0f 03 00 00 00 00 00
00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4 port SATA IDE Controller [8086:2820] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 20 Region 0: I/O ports at fe00 [size=8] Region 1: I/O ports at fe10 [size=4] Region 2: I/O ports at fe20 [size=8] Region 3: I/O ports at fe30 [size=4] Region 4: I/O ports at fec0 [size=16] Region 5: I/O ports at ecc0 [size=16] Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ata_piix 00: 86 80 20 28 07 00 b0 02 02 8f 01 01 00 00 00 00 10: 01 fe 00 00 11 fe 00 00 21 fe 00 00 31 fe 00 00 20: c1 fe 00 00 c1 ec 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 70 00 00 00 00 00 00 00 09 03 00 00 40: 07 e3 03 e3 00 00 00 00 05 00 02 01 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 00 03 40 08 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 03 83 80 01 80 40 00 00 00 00 01 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 05 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 9 Region 0: Memory at febfbb00 (32-bit, non-prefetchable) [size=256] Region 4: I/O ports at ece0 [size=32] Kernel modules: i2c-i801 00: 86 80 3e 28 03 01 80 02 02 00 05 0c 00 00 00 00 10: 00 bb bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: e1 ec 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 03 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
00:1f.5 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 2 port SATA IDE Controller [8086:2825] (rev 02) (prog-if 85 [Master SecO PriO]) Subsystem: Dell Device [1028:01da] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 20 Region 0: I/O ports at fe40 [size=8] Region 1: I/O ports at fe50 [size=4] Region 2: I/O ports at fe60 [size=8] Region 3: I/O ports at fe70 [size=4] Region 4: I/O ports at fed0 [size=16] Region 5: I/O ports at ecd0 [size=16] Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ata_piix 00: 86 80 25 28 05 00 b0 02 02 85 01 01 00 00 00 00 10: 41 fe 00 00 51 fe 00 00 61 fe 00 00 71 fe 00 00 20: d1 fe 00 00 d1 ec 00 00 00 00 00 00 28 10 da 01 30: 00 00 00 00 70 00 00 00 00 00 00 00 09 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 00 03 40 08 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 03 00 00 00 00 00
01:00.0 VGA compatible controller [0300]: nVidia Corporation G84 [Quadro FX 570] [10de:040e] (rev a1) Subsystem: nVidia Corporation Device [10de:0474] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at dc80 [size=128] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information <?> Kernel modules: nvidiafb 00: de 10 0e 04 03 00 10 00 a1 00 00 03 10 00 00 00 10: 00 00 00 fd 0c 00 00 d0 00 00 00 00 04 00 00 fa 20: 00 00 00 00 81 dc 00 00 00 00 00 00 de 10 74 04 30: 00 00 a0 fe 60 00 00 00 00 00 00 00 0b 01 00 00 40: de 10 74 04 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00 60: 01 68 02 00 00 00 00 00 05 78 80 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 10 00 01 00 e0 84 64 00 80: 16 29 00 00 01 3d 01 00 40 00 01 11 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] (rev 21) Subsystem: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 27 Region 0: Memory at f9ff0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data <?> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+ Address: 00000000fee0300c Data: 4191 Capabilities: [d0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 7d-86-2e-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 00: e4 14 59 16 06 04 10 00 21 00 00 02 10 00 00 00 10: 04 00 ff f9 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 07 00 00 00 e4 14 59 16 30: 00 00 58 e4 48 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 20 00 64 50: 03 58 e8 00 21 1d a2 56 05 d0 87 00 0c 30 e0 fe 60: 00 00 00 00 91 41 00 00 98 02 01 42 00 00 18 76 70: f2 10 00 00 c0 00 00 00 50 00 00 00 00 00 00 00 80: 03 58 e8 00 00 00 00 00 34 00 13 04 82 50 08 3c 90: 09 4f 00 01 00 00 00 00 00 00 00 00 c8 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 80 00 00 0e 00 00 00 00 00 00 00 d0: 10 00 01 00 a0 0f 28 00 00 50 10 00 11 6c 03 00 e0: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
03:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5754 Gigabit Ethernet PCI Express [14e4:167a] (rev 02) Subsystem: Dell Device [1028:01da] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 28 Region 0: Memory at f9ef0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Address: 00000000fee0300c Data: 4199 Capabilities: [d0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 86-0f-ac-fe-ff-a0-1a-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 00: e4 14 7a 16 06 04 10 00 02 00 00 02 10 00 00 00 10: 04 00 ef f9 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 da 01 30: 00 00 5b d7 48 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 01 50 03 c0 08 20 00 64 50: 03 58 c8 00 d6 f7 78 18 09 e8 78 00 88 2b 7f 6f 60: 00 00 00 00 00 00 00 00 98 02 02 b0 00 00 18 76 70: f2 10 00 00 c0 00 00 00 14 70 00 00 00 00 00 00 80: 70 9a 47 57 00 00 00 00 34 00 13 04 82 90 08 24 90: 29 92 00 01 00 00 00 00 00 00 00 00 ad 00 00 00 a0: 00 00 00 00 e5 01 00 00 00 00 00 00 b3 01 00 00 b0: 00 00 00 00 00 00 00 41 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 80 00 00 0e 00 00 00 00 00 00 00 d0: 10 00 01 00 a0 8f 28 00 00 50 10 00 11 64 03 00 e0: 40 00 11 10 00 00 00 00 05 d0 81 00 0c 30 e0 fe f0: 00 00 00 00 99 41 00 00 00 00 00 00 00 00 00 00
04:00.0 Ethernet controller [0200]: Intel Corporation 82541GI Gigabit Ethernet Controller [8086:1076] Subsystem: Intel Corporation Device [8086:1176] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at f9cc0000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at f9ce0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at ccc0 [size=64] Expansion ROM at f0000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz- Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 Kernel modules: e1000 00: 86 80 76 10 17 01 30 02 00 00 00 02 10 40 00 00 10: 00 00 cc f9 00 00 ce f9 c1 cc 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 76 11 30: 00 00 d0 f9 dc 00 00 00 00 00 00 00 0b 01 ff 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 e4 22 c8 e0: 00 20 00 28 07 f0 02 00 00 00 40 00 00 00 00 00 f0: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
04:02.0 Serial controller [0700]: Lava Computer mfg Inc Quattro-PCI A [1407:0120] (prog-if 02) Subsystem: Lava Computer mfg Inc Quattro-PCI A [1407:0120] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at cca0 [size=8] Region 1: I/O ports at cca8 [size=8] Kernel driver in use: serial 00: 07 14 20 01 41 00 80 04 00 02 00 07 00 00 80 00 10: a1 cc 00 00 a9 cc 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 07 14 20 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
04:02.1 Serial controller [0700]: Lava Computer mfg Inc Quattro-PCI B [1407:0121] (prog-if 02) Subsystem: Lava Computer mfg Inc Quattro-PCI B [1407:0121] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at ccb0 [size=8] Region 1: I/O ports at ccb8 [size=8] Kernel driver in use: serial 00: 07 14 21 01 41 00 80 04 00 02 00 07 00 00 80 00 10: b1 cc 00 00 b9 cc 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 07 14 21 01 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
superiotool -deV (version in subversion as of about the timestamp of this email)
superiotool r4931 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0x0000, rev=0x00 Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x0400, id=0x0f83 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0x830f, rev=0x9 Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0x830f, rev=0x9 Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0x830f, rev=0x9 Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x830f, rev=0x9 Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Found SMSC SCH5514D (id=0x83, rev=0x0f) at 0x2e No dump available for this Super I/O No extra registers known for this chip. Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Hi Anthony,
On 07.01.2010 22:55, Anthony DeRosa wrote:
The bios version I am currently using (2.6.2) is no longer available for download, but i happen to have a copy of it attached (raw ROM file).
I have stripped the ROM image from your mail before it could reach the list because we don't have distribution rights for ROM images.
Below is the rest of the info. you asked for.
ubuntu@ubuntu:~/flashrom$ sudo ./flashrom -r backup.bin flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... WARNING: SPI Configuration Lockdown activated. FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... OK. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Reading flash... done. ubuntu@ubuntu:~/flashrom$ hexdump backup.bin 0000000 0000 0000 0000 0000 0000 0000 0000 0000
0100000
Ouch.
dmidecode snippet (bonus!)
Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Dell Inc. Version: 2.6.2 ROM Size: 1024 kB BIOS Revision: 2.6
flashrom -V
flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 tried to set 0xdc to 0x3 on ICH8/ICH8R failed (WARNING ONLY)
OK, write to LPC flash is disabled. That's not good.
Root Complex Register Block address = 0xfeda8000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI)
Then again, your BIOS lives on SPI, so you do not care about LPC.
Top Swap : not enabled SPIBAR = 0xfeda8000 + 0x3020 0x04: 0xa000 (HSFS) FLOCKDN 1, FDV 0, FDOPSS 1, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0
FLOCKDN=1 is not that good and means we can't modify the opcodes in the chipset. FDV=0 is good.
0x50: 0x00000202 (FRAP) BMWAG 0, BMRAG 0, BRWA 2, BRRA 2 0x54: 0x00001fff (FREG0) 0x58: 0x00001fff (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00001fff (FREG3) 0x64: 0x00000000 (FREG4)
Totally weird region configuration.
0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00422004 (SSFS, SSFC) 0x94: 0x0606 (PREOP) 0x96: 0x4fc8 (OPTYPE) 0x98: 0x029fabab (OPMENU) 0x9C: 0x010502d8 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) WARNING: SPI Configuration Lockdown activated.
Good. flashrom detects the chipset lockdown.
Generating OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 512M loops per second, 100 myus = 200 us. OK. Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. No operations were specified.
Hm. can you run flashrom -c MX25L8005 -V -r backup.bin and mail us about the output? There should be at least one transaction error or somesuch. We should NOT create a dump file on error. I have a patch for that in the queue.
Regards, Carl-Daniel
carldani,
Requested output below. Invalid opcode? The MX25L8005 datasheet says the part supports opcode 0x03, read data.
-Anthony
ubuntu@ubuntu:~/flashrom$ sudo ./flashrom -c MX25L8005 -V -r backup.bin
flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 tried to set 0xdc to 0x3 on ICH8/ICH8R failed (WARNING ONLY)
Root Complex Register Block address = 0xfeda8000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfeda8000 + 0x3020 0x04: 0xa000 (HSFS) FLOCKDN 1, FDV 0, FDOPSS 1, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0 0x50: 0x00000202 (FRAP) BMWAG 0, BMRAG 0, BRWA 2, BRRA 2 0x54: 0x00001fff (FREG0) 0x58: 0x00001fff (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00001fff (FREG3) 0x64: 0x00000000 (FREG4) 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00416004 (SSFS, SSFC) 0x94: 0x0606 (PREOP) 0x96: 0x4fc8 (OPTYPE) 0x98: 0x029fabab (OPMENU) 0x9C: 0x010502d8 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) WARNING: SPI Configuration Lockdown activated. Generating OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 504M loops per second, 100 myus = 197 us. OK. Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Reading flash... Invalid OPCODE 0x03 done.
On Fri, Jan 8, 2010 at 4:22 AM, Carl-Daniel Hailfinger < c-d.hailfinger.devel.2006@gmx.net> wrote:
Hi Anthony,
On 07.01.2010 22:55, Anthony DeRosa wrote:
The bios version I am currently using (2.6.2) is no longer available for download, but i happen to have a copy of it attached (raw ROM file).
I have stripped the ROM image from your mail before it could reach the list because we don't have distribution rights for ROM images.
Below is the rest of the info. you asked for.
ubuntu@ubuntu:~/flashrom$ sudo ./flashrom -r backup.bin flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... WARNING: SPI Configuration Lockdown activated. FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... OK. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address
0xfff00000.
Reading flash... done. ubuntu@ubuntu:~/flashrom$ hexdump backup.bin 0000000 0000 0000 0000 0000 0000 0000 0000 0000
0100000
Ouch.
dmidecode snippet (bonus!)
Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Dell Inc. Version: 2.6.2 ROM Size: 1024 kB BIOS Revision: 2.6
flashrom -V
flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 tried to set 0xdc to 0x3 on ICH8/ICH8R failed (WARNING ONLY)
OK, write to LPC flash is disabled. That's not good.
Root Complex Register Block address = 0xfeda8000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1
(SPI)
Then again, your BIOS lives on SPI, so you do not care about LPC.
Top Swap : not enabled SPIBAR = 0xfeda8000 + 0x3020 0x04: 0xa000 (HSFS) FLOCKDN 1, FDV 0, FDOPSS 1, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0
FLOCKDN=1 is not that good and means we can't modify the opcodes in the chipset. FDV=0 is good.
0x50: 0x00000202 (FRAP) BMWAG 0, BMRAG 0, BRWA 2, BRRA 2 0x54: 0x00001fff (FREG0) 0x58: 0x00001fff (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00001fff (FREG3) 0x64: 0x00000000 (FREG4)
Totally weird region configuration.
0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00422004 (SSFS, SSFC) 0x94: 0x0606 (PREOP) 0x96: 0x4fc8 (OPTYPE) 0x98: 0x029fabab (OPMENU) 0x9C: 0x010502d8 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) WARNING: SPI Configuration Lockdown activated.
Good. flashrom detects the chipset lockdown.
Generating OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, FAILED! This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 512M loops per second, 100 myus = 200 us. OK. Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14.
probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address
0xfff00000.
No operations were specified.
Hm. can you run flashrom -c MX25L8005 -V -r backup.bin and mail us about the output? There should be at least one transaction error or somesuch. We should NOT create a dump file on error. I have a patch for that in the queue.
Regards, Carl-Daniel
-- Developer quote of the year: "We are juggling too many chainsaws and flaming arrows and tigers."
Hi Anthony,
On Fri, Jan 8, 2010 at 4:16 PM, Anthony DeRosa anthony@ransomed.us wrote:
carldani,
Requested output below. Invalid opcode? The MX25L8005 datasheet says the part supports opcode 0x03, read data.
IIRC the newer Dell OptiPlex series have a special way for flashing the BIOS. You use a Dell-provided utility to copy the new BIOS image into a special (non-volatile?) memory, then reboot the machine. Once it reboots, it will automatically start to flash. The same technique is used by IBM with most of their Thinkpad models, I don't know whether this still applies to the more recent Lenovo models.
Btw: I think Dell also provides flash utilities for Linux (since they ship machines with Ubuntu), but my memory might deceive me ;).
Adrian
On Fri, Jan 8, 2010 at 8:32 AM, Adrian Glaubitz adrian.glaubitz@googlemail.com wrote:
IIRC the newer Dell OptiPlex series have a special way for flashing the BIOS. You use a Dell-provided utility to copy the new BIOS image into a special (non-volatile?) memory, then reboot the machine. Once it reboots, it will automatically start to flash.
wow, how ... special. So you have no visibility into the reflash process and no idea of its progress.
This is the default mode for many new BIOSes, I understand, since so many of them are EFI at the core. It's not an improvement for the customer, but it's what the vendors are going to provide. It's very disappointing.
ron
On 08.01.2010 18:06, ron minnich wrote:
On Fri, Jan 8, 2010 at 8:32 AM, Adrian Glaubitz wrote
IIRC the newer Dell OptiPlex series have a special way for flashing the BIOS. You use a Dell-provided utility to copy the new BIOS image into a special (non-volatile?) memory, then reboot the machine. Once it reboots, it will automatically start to flash.
wow, how ... special. So you have no visibility into the reflash process and no idea of its progress.
I think the special Dell stuff has existed for years. Back then, they probably didn't know (or didn't care) about flashrom, and nowadays this flashing procedure is actually a reliability advantage over the alternative: Windows flashers. Flashing from a multitasking OS (especially if not done as kernel driver) means there are no guarantees whatsoever about timing, reliability, crash resistance and other stuff you'd care about. You can find boatloads of reports from people who bricked their machines by flashing under Windows, and because people are too unskilled (or unwilling) to run DOS based flashers, it all burns down to doing the reflashing from the BIOS.
This is the default mode for many new BIOSes, I understand, since so many of them are EFI at the core. It's not an improvement for the customer, but it's what the vendors are going to provide. It's very disappointing.
I think this is only somewhat related to EFI (first time you can easily add executables to the BIOS). Most of it is about reliability concerns. And if you look at vendors like Sun, it seems there is an unwillingness to perform host-based flashing at all, instead they opt to run the reflashing process from the Management Engine.
I see a flashrom driver for such Management Engines on the horizon (unless they are not providing direct hardware access), but since I don't own the hardware, this is pretty low priority for me.
Now if we could motivate at least one board vendor to ship (or offer for download) flashrom CDs for reflashing their boards, we'd win big time.
Regards, Carl-Daniel
On Fri, Jan 08, 2010 at 09:06:52AM -0800, ron minnich wrote:
On Fri, Jan 8, 2010 at 8:32 AM, Adrian Glaubitz adrian.glaubitz@googlemail.com wrote:
IIRC the newer Dell OptiPlex series have a special way for flashing the BIOS. You use a Dell-provided utility to copy the new BIOS image into a special (non-volatile?) memory, then reboot the machine. Once it reboots, it will automatically start to flash.
wow, how ... special. So you have no visibility into the reflash process and no idea of its progress.
This is the default mode for many new BIOSes, I understand, since so many of them are EFI at the core. It's not an improvement for the customer, but it's what the vendors are going to provide. It's very disappointing.
I see one very good reason to try this (apart from several negative ones): Malware. If malware manages to program itself into the BIOS, then it will control what the OS sees - and has possibility to thwart any and all attempts at detecting/repairing such a program. If the BIOS only accepts signed BIOS updates for reflashing, then this could prevent that kind of malware.
Ciao Joerg
On 08.01.2010 16:16, Anthony DeRosa wrote:
Requested output below. Invalid opcode? The MX25L8005 datasheet says the part supports opcode 0x03, read data.
As discussed on IRC, the READ opcode 0x03 is not supported by your chipset configuration.
ubuntu@ubuntu:~/flashrom$ sudo ./flashrom -c MX25L8005 -V -r backup.bin
flashrom v0.9.1-r837 No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... [...] BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) FLOCKDN 1, FDV 0, FDOPSS 1, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0 0x98: 0x029fabab (OPMENU) 0x9C: 0x010502d8 (OPMENU+4) [...] WARNING: SPI Configuration Lockdown activated. Generating OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, FAILED! This chipset supports the following protocols: FWH,SPI. Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Reading flash... Invalid OPCODE 0x03 done.
This is a bug, though. If we encounter an Invalid opcode error during read, we should NOT write that file at all, and we should NOT report success. Will fix.
Regards, Carl-Daniel
-
Adrian Glaubitz -
Anthony DeRosa -
Carl-Daniel Hailfinger -
Joerg Mayer -
ron minnich