Report: Intel HM67 #2 read

flashrom v0.9.6.1-r1622 on Darwin 12.2.0 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.1.9, LLVM Clang 4.1 ((tags/Apple/clang-421.11.66)), little endian
Command line (5 args): ~/Downloads/DPCIManager/DPCIManager.app/Contents/MacOS/flashrom -VV -r ~/Desktop/Kexts/bios.rom -p internal
Calibrating delay loop... OS timer resolution is 1 usecs, 329M loops per second, 10 myus = 10 us, 100 myus = 104 us, 1000 myus = 1016 us, 10000 myus = 10062 us, 4 myus = 5 us, OK.
Initializing internal programmer
Mapping low megabyte at 0x00000400, unaligned size 0xffc00.
Mapping low megabyte, 0xffc00 bytes at unaligned 0x00000400.
No coreboot table found.
sh: dmidecode: command not found
dmidecode execution unsuccessful - continuing without DMI info
W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: 85.
Please send the output of "flashrom -V" to 
[e-mail] with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
Found ITE EC, ID 0x8518,Rev 0x02 on port 0x4e.
Found chipset "Intel HM67" with PCI ID 8086:1c4b. 
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to [e-mail] including a verbose (-V) log.
Thank you!
Enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x0
0xffe00000/0xffa00000 FWH IDSEL: 0x0
0xffd80000/0xff980000 FWH IDSEL: 0x0
0xffd00000/0xff900000 FWH IDSEL: 0x0
0xffc80000/0xff880000 FWH IDSEL: 0x0
0xffc00000/0xff800000 FWH IDSEL: 0xf
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x380000 bytes
BIOS_CNTL = 0x09: BIOS Lock Enable: disabled, BIOS Write Enable: enabled
Root Complex Register Block address = 0xfed1c000
GCS = 0xc20: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap : not enabled
SPIBAR = 0xfed1c000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
WARNING: SPI Configuration Lockdown activated.
Reading OPCODES... done
        OP        Type      Pre-OP
op[0]: 0x00, read  w/o addr, none
op[1]: 0x00, read  w/o addr, none
op[2]: 0x00, read  w/o addr, none
op[3]: 0x00, read  w/o addr, none
op[4]: 0x00, read  w/o addr, none
op[5]: 0x00, read  w/o addr, none
op[6]: 0x00, read  w/o addr, none
op[7]: 0x00, read  w/o addr, none
Pre-OP 0: 0x00, Pre-OP 1: 0x00
0x06: 0x0000 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0
0x08: 0x00000000 (FADDR)
0x50: 0x00000a0b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b
0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write.
0x5C: 0x017f0001 FREG2: WARNING: Management Engine region (0x00001000-0x0017ffff) is locked.
0x60: 0x00000fff FREG3: Gigabit Ethernet region is unused.
0x64: 0x00000fff FREG4: Platform Data region is unused.
0x74: 0x00000000 (PR0 is unused)
0x78: 0x00000000 (PR1 is unused)
0x7C: 0x00000000 (PR2 is unused)
0x80: 0x00000000 (PR3 is unused)
0x84: 0x00000000 (PR4 is unused)
Please send a verbose log to [e-mail] if this board is not listed on
http://flashrom.org/Supported_hardware#Supported_mainboards yet.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0x80 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf80000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0
0x94: 0x0000     (PREOP)
0x96: 0x0000     (OPTYPE)
0x98: 0x00000000 (OPMENU)
0x9C: 0x00000000 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0
0xD0: 0x00000000 (FPB)

Reading flash descriptors mapped by the chipset via FDOC/FDOD... done.
=== Content Section ===
FLVALSIG 0x0ff0a55a
FLMAP0   0x02040003
FLMAP1   0x12100206
FLMAP2   0x00210120

--- Details ---
NR          (Number of Regions):                     3
FRBA        (Flash Region Base Address):         0x040
NC          (Number of Components):                  1
FCBA        (Flash Component Base Address):      0x030
ISL         (ICH/PCH Strap Length):                 18
FISBA/FPSBA (Flash ICH/PCH Strap Base Address):  0x100
NM          (Number of Masters):                     3
FMBA        (Flash Master Base Address):         0x060
MSL/PSL     (MCH/PROC Strap Length):                 1
FMSBA       (Flash MCH/PROC Strap Base Address): 0x200

=== Component Section ===
FLCOMP   0x09300023
FLILL    0x00000000

--- Details ---
Component 1 density:             4 MB
Component 2 is not used.
Read Clock Frequency:           20 MHz
Read ID and Status Clock Freq.: 33 MHz
Write and Erase Clock Freq.:    33 MHz
Fast Read is supported.
Fast Read Clock Frequency:      33 MHz
No forbidden opcodes.

=== Region Section ===
FLREG0   0x00000000
FLREG1   0x03ff0180
FLREG2   0x017f0001
FLREG3   0x00000fff

--- Details ---
Region 0 (Descr.) 0x00000000 - 0x00000fff
Region 1 (BIOS  ) 0x00180000 - 0x003fffff
Region 2 (ME    ) 0x00001000 - 0x0017ffff
Region 3 (GbE   ) is unused.

=== Master Section ===
FLMSTR1  0x0a0b0000
FLMSTR2  0x0c0d0000
FLMSTR3  0x08080118

--- Details ---
      Descr. BIOS ME GbE Platf.
BIOS    r     rw      rw     
ME      r         rw  rw     
GbE                   rw

Enabling hardware sequencing because some important opcode is locked.
SPI Read Configuration: prefetching enabled, caching enabled, OK.
Super I/O ID 0x8518 is not on the list of flash capable controllers.
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip with a density of 4096 kB.
There is only one partition containing the whole address space (0x000000 - 0x3fffff).
There are 1024 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (4096 kB, Programmer-specific) at physical address 0x0.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xfc, id2 0x51, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xfc, id2 0x51, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xfc, id2 0x51, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0x75, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xcc, id2 0x06, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xfc, id2 0x51, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xcc, id2 0x06, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xfc, id2 0x51, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xc7, id2 0x1a, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (4096 kB, Programmer-specific).
Reading flash... Reading 4194304 bytes starting at 0x000000.
Transaction error between offset 0x00001000 and 0x0000103f (= 0x00001000 + 63)!
Read operation failed!
HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
FAILED.
Restoring MMIO space at 0x1078358a0
Restoring PCI config space for 00:1f:0 reg 0xdc