# flashrom -r backup.bin -VV flashrom v0.9.5-r1503 on Linux 3.0-ARCH (x86_64), built with libpci 3.1.9, GCC 4.6.2 20120120 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 1797M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1000 us, 10000 myus = 10011 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. sh: dmidecode: command not found dmidecode execution unsuccessful - continuing without DMI info Found chipset "Intel ICH8DH" with PCI ID 8086:2812. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 WARNING: Setting 0xdc from 0x2 to 0x3 on ICH8DH failed. New value is 0x2. Root Complex Register Block address = 0xfed1c000 GCS = 0x880464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3020 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done OP Type Pre-OP op[0]: 0x9f, read w/o addr, none op[1]: 0xab, read w/ addr, none op[2]: 0x00, read w/o addr, none op[3]: 0x00, read w/o addr, none op[4]: 0x00, read w/o addr, none op[5]: 0x00, read w/o addr, none op[6]: 0x00, read w/o addr, none op[7]: 0x00, read w/o addr, none Pre-OP 0: 0x00, Pre-OP 1: 0x00 0x06: 0x3f00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 0x08: 0x00003000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x00ff0035 FREG1: BIOS region (0x00035000-0x000fffff) is read-write. 0x5C: 0x00340003 FREG2: WARNING: Management Engine region (0x00003000-0x00034fff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00000000 FREG4: WARNING: Platform Data region (0x00000000-0x00000fff) is locked. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom@flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x04 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0x004200 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=2, SME=0, SCF=0 0x94: 0x0000 (PREOP) 0x96: 0x0008 (OPTYPE) 0x98: 0x0000ab9f (OPMENU) 0x9C: 0x00000000 (OPMENU+4) 0xC1: 0xffffffff (VSCC) VSCC: BES=0x3, WG=1, WSR=1, WEWS=1, EO=0xff, VCL=1
Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040001 FLMAP1 0x01100206 FLMAP2 0x00000120
--- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x010 ISL (ICH/PCH Strap Length): 1 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200
=== Component Section === FLCOMP 0x00300001 FLILL 0x00000000
--- Details --- Component 1 density: 1 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 20 MHz Write and Erase Clock Freq.: 20 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes.
=== Region Section === FLREG0 0x00000000 FLREG1 0x00ff0035 FLREG2 0x00340003 FLREG3 0x00020001 FLREG4 0x00000000
--- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00035000 - 0x000fffff Region 2 (ME ) 0x00003000 - 0x00034fff Region 3 (GbE ) 0x00001000 - 0x00002fff Region 4 (Platf.) 0x00000000 - 0x00000fff
=== Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08090218
--- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE r rw
Enabling hardware sequencing because some important opcode is locked. SPI Read Configuration: prefetching disabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip with a density of 1024 kB. There is only one partition containing the whole address space (0x000000 - 0x0fffff). There are 256 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific) at physical address 0x0. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x89, id2 0x89, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x89, id2 0x89, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x89, id2 0x89, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x48, id2 0x2a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x89, id2 0x89, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x89, id2 0x89, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xd3, id2 0x56, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific). Reading flash... Reading 1048576 bytes starting at 0x000000. Transaction error between offset 0x00003000 and 0x0000303f (= 0x00003000 + 63)! HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 Read operation failed! FAILED. Restoring PCI config space for 00:1f:0 reg 0xdc