flashrom

flashrom@flashrom.org

5 participants
9099 discussions

Start a nNew thread

flashroom success with msi 7321 v1.0 mb (k9MM-V)
by David Mears 05 Feb '10

05 Feb '10

seems to hose the MAC address on the onboard lan, though.

1 0

building 32-bit on 64-bit
by ron minnich 04 Feb '10

04 Feb '10

I'm sorry if there is an obvious answer but how is that done? thanks ron

2 1

[PATCH] Locking infrastructure and locking for W39V080FA and PMC 49LF040
by Sean Nelson 04 Feb '10

04 Feb '10

Locking infrastructure Add lock-status command option. Winbond W39V080FA has 64k lock blocks. PMC Pm49FL004 has 64k lock blocks. Tested, but write/erase fails. PMC Pm49FL002 has 32k lock blocks. Signed-off-by: Sean Nelson <audiohacked(a)gmail.com> --- Added dumps from an Compaq desktop with ASUS A8N-LA; just in case. Stepan if you could please test this and tell me if it works or not.

2 2

Call for photos: External programmers
by Carl-Daniel Hailfinger 04 Feb '10

04 Feb '10

Hi, I'd like to spice up my FOSDEM presentation with a few photos of supported (and WIP) external programmers. If you have any photos of SiliconImage SATA, Highpoint IDE, Nvidia graphics etc, please mail them to me or point me to a place where I can download them. Thanks! Regards, Carl-Daniel -- Developer quote of the year: "We are juggling too many chainsaws and flaming arrows and tigers."

1 0

test report
by Solomon Peachy 04 Feb '10

04 Feb '10

sudo ./flashrom flashrom v0.9.1-r893 No coreboot table found. sh: dmidecode: command not found Found ITE SuperI/O, id 8716 Found chipset "NVIDIA MCP51", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... OK. Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. I've sucecssfully flashed this part with the 0.9.1 release, on a PCCHIPS A11G motherboard. - Solomon -- Solomon Peachy solomon(a)linux-wlan.com AbsoluteValue Systems http://www.linux-wlan.com 721-D North Drive +1 (321) 259-0737 (office) Melbourne, FL 32934 +1 (321) 259-0286 (fax)

1 0

[commit] r893 - trunk
by repository service 04 Feb '10

04 Feb '10

Author: hailfinger Date: Thu Feb 4 12:12:04 2010 New Revision: 893 URL: http://flashrom.org/trac/coreboot/changeset/893 Log: Document the rules for DMI matching with PCI subsystem IDs. The rules may change in the future, but right now it is important that the comments match the code. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/board_enable.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Thu Feb 4 11:58:50 2010 (r892) +++ trunk/board_enable.c Thu Feb 4 12:12:04 2010 (r893) @@ -1160,9 +1160,10 @@ * subsystem/card IDs in a sane manner. * * Keep the second set NULLed if it should be ignored. Keep the subsystem IDs - * NULLed if they don't identify the board fully. But please take care to - * provide an as complete set of pci ids as possible; autodetection is the - * preferred behaviour and we would like to make sure that matches are unique. + * NULLed if they don't identify the board fully and if you can't use DMI. + * But please take care to provide an as complete set of pci ids as possible; + * autodetection is the preferred behaviour and we would like to make sure that + * matches are unique. * * If PCI IDs are not sufficient for board matching, the match can be further * constrained by a string that has to be present in the DMI database for @@ -1171,6 +1172,11 @@ * or the end (with a $ at the end). Both anchors may be specified at the * same time to match the full field. * + * When a board is matched through DMI, the first and second main PCI IDs + * and the first subsystem PCI ID have to match as well. If you specify the + * first subsystem ID as 0x0:0x0, the DMI matching code expects that the + * subsystem ID of that device is indeed zero. + * * The coreboot ids are used two fold. When running with a coreboot firmware, * the ids uniquely matches the coreboot board identification string. When a * legacy bios is installed and when autodetection is not possible, these ids

1 0

Re: [flashrom] [PATCH] (now for real!) Allow DMI supported board enables with subsystem ID zero.
by Carl-Daniel Hailfinger 04 Feb '10

04 Feb '10

On 04.02.2010 11:19, Michael Karcher wrote: > This is needed for the Intel SE440BX-2 as well as the Asus P5A. > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel -- Developer quote of the year: "We are juggling too many chainsaws and flaming arrows and tigers."

2 1

[commit] r892 - trunk
by repository service 04 Feb '10

04 Feb '10

Author: mkarcher Date: Thu Feb 4 11:58:50 2010 New Revision: 892 URL: http://flashrom.org/trac/coreboot/changeset/892 Log: Allow DMI supported board enables with subsystem ID zero. This is needed for the Intel SE440BX-2 as well as the Asus P5A. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/board_enable.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Thu Feb 4 09:29:18 2010 (r891) +++ trunk/board_enable.c Thu Feb 4 11:58:50 2010 (r892) @@ -1305,7 +1305,8 @@ struct board_pciid_enable *board = board_pciid_enables; for (; board->vendor_name; board++) { - if (!board->first_card_vendor || !board->first_card_device) + if ((!board->first_card_vendor || !board->first_card_device) && + !board->dmi_pattern) continue; if (!pci_card_find(board->first_vendor, board->first_device,

1 0

[PATCH] (now for real!) Allow DMI supported board enables with subsystem ID zero.
by Michael Karcher 04 Feb '10

04 Feb '10

This is needed for the Intel SE440BX-2 as well as the Asus P5A. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Now *REALLY* with the right patch. I supposed I knew how to operate git :( --- board_enable.c | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/board_enable.c b/board_enable.c index 40db653..c73c8af 100644 --- a/board_enable.c +++ b/board_enable.c @@ -1312,7 +1312,8 @@ static struct board_pciid_enable *board_match_pci_card_ids(void) struct board_pciid_enable *board = board_pciid_enables; for (; board->vendor_name; board++) { - if (!board->first_card_vendor || !board->first_card_device) + if ((!board->first_card_vendor || !board->first_card_device) && + !board->dmi_pattern) continue; if (!pci_card_find(board->first_vendor, board->first_device, -- 1.6.5

1 0

Re: [flashrom] [PATCH] (fixed) Allow DMI supported board enables with subsystem ID zero.
by Carl-Daniel Hailfinger 04 Feb '10

04 Feb '10

On 04.02.2010 10:59, Michael Karcher wrote: > This is needed for the Intel SE440BX-2 as well as the Asus P5A. > > Thanks to Carl-Daniel Hailfinger for pointing out wrong logic in > the patch. > > Zach: please retry with this one instead of the previous version of > this patch. You can unpatch the previous version by > patch -R < oldpatch.diff > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > AFAICS you reposted the old patch. Regards, Carl-Daniel -- Developer quote of the year: "We are juggling too many chainsaws and flaming arrows and tigers."

1 0

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom