flashrom

flashrom@flashrom.org

3 participants
9189 discussions

FAILED: SST SST39SF040 - Verify Failed
by Roger 13 Jan '11

13 Jan '11

localhost2 bios # flashrom -w /home/roger/src/coreboot-tyan_s1832dl/coreboot/build/coreboot.rom flashrom v0.9.3-r1205 on Linux 2.6.37-gentoo (i686), built with libpci 3.1.4, GCC 4.4.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "Intel PIIX4/4E/4M", enabling flash write... OK. This chipset supports the following protocols: Parallel. Found chip "SST SST39SF040" (512 KB, Parallel) at physical address 0xfff80000. Note: If the following flash access fails, try -m <vendor>:<mainboard>. Writing flash chip... Erasing flash chip... SUCCESS. Programming page: DONE!ss: 0x0007f000 COMPLETE. Verifying flash... VERIFY FAILED at 0x0003fc9e! Expected=0xff, Read=0x4f, failed byte count from 0x00000000-0x0007ffff: 0x231f7 Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! DIGI-KEY Part No. SST39SF040-70-4C-PHE IC FLASH MPF 4MBIT (512KBYTES) 70NS 32DIP This is flashing using a Tyan S1832DL board 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) ... 00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02) (... am I getting this right, flashrom uses the ISA bridge to write to flash part?) -- Roger http://rogerx.freeshell.org/

2 2

[PATCH] remove umlauts from man page
by Stefan Reinauer 13 Jan '11

13 Jan '11

See patch.

1 0

LV-678 chipset detection
by Carl-Daniel Hailfinger 13 Jan '11

13 Jan '11

Hi, you reported a flashrom issue on IRC and uploaded your logs to http://paste.flashrom.org/view.php?id=299 Could you please retry with current flashrom (at least 0.9.3, preferably 0.9.3-r1250) and report success or failure? The flashrom version you were using is extremely old, it does not even have a version number. Current flashrom should detect the chipset without problems, and verbose mode should tell you a lot about the flash read/write permissions of your mainboard. Please reply with the output of "flashrom -V" from a current flashrom binary or upload the output to http://paste.flashrom.org/ and include the link in your mail. Regards, Carl-Daniel -- http://www.hailfinger.org/

1 0

Erase Fails on Winmate I370
by sdbarnes＠rockwellcollins.com 12 Jan '11

12 Jan '11

Hi Guys, I was hoping someone could help me with the following problem. I can read the flash ROM contents without a problem and write the same flash ROM contents without a problem using flashrom-0.9.3.-r1250 but if I try to write a new ROM provided by the motherboard manufacturer, the erase function fails. Below is the output from flashrom and lspci. I can read succcessfully read the flash ROM contents: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - [root]#./flashrom -r I370.bin flashrom v0.9.3-r1250 on Linux 2.6.24.7 (i686), built with libpci 2.2.9, GCC 4.1.2 20070925 (Red Hat 4.1.2-33), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Invalid string keyword: chassis-type Valid string keywords are: bios-vendor bios-version bios-release-date system-manufacturer system-product-name system-version system-serial-number baseboard-manufacturer baseboard-product-name baseboard-version baseboard-serial-number baseboard-asset-tag chassis-manufacturer chassis-version chassis-serial-number chassis-asset-tag processor-manufacturer processor-version dmidecode execution unsucessfull - continuing without DMI info Found chipset "Intel ICH7M", enabling flash write... OK. This chipset supports the following protocols: FWH. Found chip "Winbond W39V040FC" (512 KB, FWH) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... done. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - I can also successfully write the same flash ROM contents: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - [root]#./flashrom -w I370.bin flashrom v0.9.3-r1250 on Linux 2.6.24.7 (i686), built with libpci 2.2.9, GCC 4.1.2 20070925 (Red Hat 4.1.2-33), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Invalid string keyword: chassis-type Valid string keywords are: bios-vendor bios-version bios-release-date system-manufacturer system-product-name system-version system-serial-number baseboard-manufacturer baseboard-product-name baseboard-version baseboard-serial-number baseboard-asset-tag chassis-manufacturer chassis-version chassis-serial-number chassis-asset-tag processor-manufacturer processor-version dmidecode execution unsucessfull - continuing without DMI info Found chipset "Intel ICH7M", enabling flash write... OK. This chipset supports the following protocols: FWH. Found chip "Winbond W39V040FC" (512 KB, FWH) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Flash image seems to be a legacy BIOS. Disabling checks. Erasing and writing flash chip... Done. Verifying flash... VERIFIED. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - However, when I try to write a new flash ROM (provided by the motherboard manufacturer), the erase function fails: [root]#./flashrom -w i3700n1t.bin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - flashrom v0.9.3-r1250 on Linux 2.6.24.7 (i686), built with libpci 2.2.9, GCC 4.1.2 20070925 (Red Hat 4.1.2-33), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Invalid string keyword: chassis-type Valid string keywords are: bios-vendor bios-version bios-release-date system-manufacturer system-product-name system-version system-serial-number baseboard-manufacturer baseboard-product-name baseboard-version baseboard-serial-number baseboard-asset-tag chassis-manufacturer chassis-version chassis-serial-number chassis-asset-tag processor-manufacturer processor-version dmidecode execution unsucessfull - continuing without DMI info Found chipset "Intel ICH7M", enabling flash write... OK. This chipset supports the following protocols: FWH. Found chip "Winbond W39V040FC" (512 KB, FWH) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Flash image seems to be a legacy BIOS. Disabling checks. Erasing and writing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0000ffff: 0x3ec ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x5437e ERASE FAILED! Done. Verifying flash... VERIFY FAILED at 0x00000000! Expected=0xed, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x13ea Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Below is the output lspci output: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03) Subsystem: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> Kernel driver in use: agpgart-intel 00: 86 80 ac 27 06 00 90 20 03 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 ac 27 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 90 d1 fe 01 40 d1 fe 01 00 00 e0 01 80 d1 fe 50: 00 00 30 00 09 00 00 00 00 00 00 00 00 00 00 00 60: 01 30 d1 fe 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 11 01 00 11 11 00 ff 03 00 00 40 1a 38 00 a0: 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 11 01 00 00 e0: 09 00 09 51 02 04 4a 90 0e 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 05 00 00 00 00 00 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at ff00 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 86 80 ae 27 07 00 90 00 03 00 00 03 00 00 00 00 10: 00 00 f0 fd 01 ff 00 00 08 00 00 d0 00 00 f8 fd 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 ae 27 30: 00 00 00 00 90 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 48 00 00 00 09 00 09 51 02 04 4a 90 50: 0e 00 30 00 09 00 00 00 00 00 00 00 00 00 80 3f 60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 05 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 05 64 34 00 00 00 00 86 0f 05 00 00 00 00 00 00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 10, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: fee0100c Data: 41b9 Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver 00: 86 80 d0 27 07 04 10 00 02 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 c0 c0 00 00 20: e0 fd e0 fd b1 fd b1 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00 40: 10 80 41 01 c0 0f 00 00 04 00 10 00 11 2c 11 01 50: 40 00 11 30 60 05 80 00 00 00 40 00 04 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 0c 10 e0 fe b9 41 00 00 00 00 00 00 90: 0d a0 00 00 86 80 d0 27 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 80 00 11 80 00 00 00 00 e0: 00 0f c7 00 06 07 08 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 11, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: fee0100c Data: 41c1 Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver 00: 86 80 d2 27 07 04 10 00 02 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 b0 b0 00 00 20: a0 fd a0 fd 91 fd 91 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 00 00 40: 10 80 41 01 c0 0f 00 00 04 00 10 00 11 2c 11 02 50: 40 00 11 30 60 05 88 00 00 00 40 00 04 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 0c 10 e0 fe c1 41 00 00 00 00 00 00 90: 0d a0 00 00 86 80 d2 27 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 80 00 11 80 00 00 00 00 e0: 00 0f c7 00 06 07 08 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 4: I/O ports at fe00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00: 86 80 c8 27 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 fe 00 00 00 00 00 00 00 00 00 00 86 80 c8 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 01 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at fd00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00: 86 80 c9 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 fd 00 00 00 00 00 00 00 00 00 00 86 80 c9 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 01 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 20 Region 4: I/O ports at fc00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00: 86 80 ca 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 fc 00 00 00 00 00 00 00 00 00 00 86 80 ca 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 01 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at fb00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00: 86 80 cb 27 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 fb 00 00 00 00 00 00 00 00 00 00 86 80 cb 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 04 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 01 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00: 86 80 cc 27 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 f0 ff fd 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 cc 27 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 00 00 00 00 00 01 00 00 00 00 00 08 c0 70: 00 00 30 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 11 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 ff 00 ff 00 20 00 00 88 e0: 00 00 00 00 db b6 6d 00 00 00 00 00 00 00 00 00 f0: 00 80 00 09 88 85 40 00 86 0f 02 00 86 17 02 20 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fdd00000-fddfffff Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] 00: 86 80 48 24 07 00 10 00 e2 01 04 06 00 00 81 00 10: 00 00 00 00 00 00 00 00 00 03 03 20 d0 d0 80 22 20: d0 fd d0 fd c1 fd c1 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 50: 0d 00 00 00 86 80 48 24 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801G (ICH7 Family) AC'97 Audio Controller [8086:27de] (rev 02) Subsystem: Unknown device [414c:4760] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at f000 [size=256] Region 1: I/O ports at fa00 [size=64] Region 2: Memory at fdffe000 (32-bit, non-prefetchable) [size=512] Region 3: Memory at fdffd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: Intel ICH Kernel modules: snd-intel8x0 00: 86 80 de 27 07 00 90 02 02 00 01 04 00 00 00 00 10: 01 f0 00 00 01 fa 00 00 00 e0 ff fd 00 d0 ff fd 20: 00 00 00 00 00 00 00 00 00 00 00 00 4c 41 60 47 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00 40: 09 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 c2 c9 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02) Subsystem: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt, intel-rng 00: 86 80 b9 27 07 01 10 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 b9 27 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 04 00 00 80 00 00 00 81 04 00 00 10 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 85 8a 8a 8b d0 00 00 00 87 80 80 8b 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 07 00 09 34 81 02 7c 00 f9 03 04 00 e9 03 04 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 20 06 00 00 08 00 00 00 13 00 00 00 00 03 00 00 b0: 00 00 f0 00 00 00 00 00 55 55 55 59 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 33 22 11 00 67 45 00 00 c0 ff 00 00 01 00 00 00 e0: 09 00 0c 10 b4 02 24 17 00 00 00 00 00 00 00 00 f0: 01 c0 d1 fe 00 00 00 00 86 0f 02 00 00 00 00 00 00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at f800 [size=16] Kernel driver in use: ata_piix Kernel modules: ata_piix 00: 86 80 df 27 05 00 80 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 20: 01 f8 00 00 00 00 00 00 00 00 00 00 86 80 df 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00 40: 07 e3 00 c0 00 00 00 00 01 00 02 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 0500 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c-i801 00: 86 80 da 27 01 00 80 02 02 00 05 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 05 00 00 00 00 00 00 00 00 00 00 86 80 da 27 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 221 Region 0: I/O ports at ce00 [size=256] Region 2: Memory at fdeff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Vital Product Data <?> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0100c Data: 41e1 Capabilities: [60] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <128ns, L1 unlimited ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [84] Vendor Specific Information <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [12c] Virtual Channel <?> Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-01-34 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 00: ec 10 68 81 07 04 10 00 01 00 00 02 10 00 00 00 10: 01 ce 00 00 00 00 00 00 04 f0 ef fd 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 68 81 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00 40: 01 48 c2 f7 00 00 00 00 03 50 00 00 00 00 00 00 50: 05 60 83 00 0c 10 e0 fe 00 00 00 00 e1 41 00 00 60: 10 84 01 00 63 7e 00 00 10 58 10 00 11 f4 03 00 70: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 09 00 4c 01 01 1c 02 00 fb ff ff 11 90: 08 30 00 00 17 6f 09 00 55 30 0b 00 d6 04 00 00 a0: 02 28 ff 01 00 00 00 00 00 08 00 00 03 00 03 00 b0: 00 00 00 00 ff 3f ff 3f ff ff 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 220 Region 0: I/O ports at be00 [size=256] Region 2: Memory at fdaff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fd900000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Vital Product Data <?> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: fffffffffff0100c Data: ffe9 Capabilities: [60] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <128ns, L1 unlimited ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [84] Vendor Specific Information <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [12c] Virtual Channel <?> Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-01-35 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 00: ec 10 68 81 07 04 10 00 01 00 00 02 10 00 00 00 10: 01 be 00 00 00 00 00 00 04 f0 af fd 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 68 81 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00 40: 01 48 c2 f7 00 00 00 00 03 50 00 00 00 00 00 00 50: 05 60 83 00 0c 10 f0 ff ff ff ff ff e9 ff 00 00 60: 10 84 01 00 63 7e 00 00 10 58 10 00 11 f4 03 00 70: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 09 00 4c 01 01 1c 02 00 fb ff ff 11 90: 08 30 00 00 f7 61 07 00 52 40 06 00 b8 03 00 00 a0: 02 28 ff 01 00 00 00 00 00 08 00 00 03 00 03 00 b0: 00 00 00 00 ff 3f ff 3f ff ff 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

1 0

Bios update problem
by Bence Kovács 12 Jan '11

12 Jan '11

Dear, I need help in the following: I wanted to update my flash with a bitmap fullscreen logo. The system runs ubuntu 10.04 with real-time rtai. I red the flash with flashrom (attached: originalflash.bin) and copy file to a windows PC. (Reading flash completed successfully) I run Award Bios editor 1.0, which successfully realized all parameters of flash file. I modified bios with a bitmap used CBROM196 (attached: modifiedflash.bin). I run Award Bios editor, which realized valid the new flash file as well. I tried to download the modified file, but got the messages bellow. I red the flash out, checked with Award bios editor, and flash file was the old one (originalflash.bin). I downloaded originalflash.bin, and got the same message bellow. I red out, checked with Award bios editor, and it was the old flash file again (originalflash.bin). Verify to originalflash.bin works as well. It seems, that read works properly, and write does nothing. But still, Im a bit afraid to restart the computer. What do you thing? (I leave computer on until answer) (Less important question: How should I modify flash? ) Thank you for help, Bence Kovacs generalmechatronics@generalmechatronics-desktop:~$ sudo flashrom -r "originalflash.bin" flashrom v0.9.1-r946 No coreboot table found. Found chipset "Intel ICH6/ICH6R", enabling flash write... OK. This chipset supports the following protocols: FWH. Calibrating delay loop... OK. Found chip "Winbond W39V040FA" (512 KB, FWH) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Reading flash... done. generalmechatronics@generalmechatronics-desktop:~$ sudo flashrom -w "modifiedflash.bin" flashrom v0.9.1-r946 No coreboot table found. Found chipset "Intel ICH6/ICH6R", enabling flash write... OK. This chipset supports the following protocols: FWH. Calibrating delay loop... OK. Found chip "Winbond W39V040FA" (512 KB, FWH) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x00000fff: 0x4ab ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0000ffff: 0xca1 ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x65f4b ERASE FAILED! FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! A non-text attachment has been removed: originalflash.bin It is available at http://paste.flashrom.org/view.php?id=297 A non-text attachment has been removed: modifiedflash.bin It is available at http://paste.flashrom.org/view.php?id=298

2 1

Re: [flashrom] Why is ther not a simple How to?
by Michael Karcher 12 Jan '11

12 Jan '11

Am Montag, den 10.01.2011, 11:26 -0500 schrieb Dan Perry: > > You are looking at the *source* code of a unix manual page. Please use > > "man -l flashrom.8" instead to read that file in a formatted way. > > > > Regards, > > Michael Karcher > Thanks for the reply, but where is that? Where is what? The file you quoted is included in the flashrom source code as "flashrom.8". If you have installed a flashrom binary from a distribution, the man page is already installed, and can be invoked by running "man flashrom". Be advised that the flashrom binary from debian stable ("lenny") is extremely outdated, though. Regards, Michael Karcher

2 1

Why is ther not a simple How to?
by Dan Perry 10 Jan '11

10 Jan '11

I find this is true of a lot of utilities. Why is there not a simple step by step How to.. ? I have looked over the documentation and now I know how to make a donation but to hell if anything even gives me a hint as to how I flash my BIOS. The one link that I can find that says "How can I use flashrom?" looks like: 1 .TH FLASHROM 8 "Jun 06, 2010" 2 .SH NAME 3 flashrom \- detect, read, write, verify and erase flash chips 4 .SH SYNOPSIS 5 .B flashrom \fR[\fB\-n\fR] [\fB\-V\fR] [\fB\-f\fR] [\fB\-h\fR|\fB\-R\fR|\ 6 \fB\-L\fR|\fB\-z\fR|\fB\-E\fR|\fB\-r\fR <file>|\fB\-w\fR <file>|\ 7 \fB\-v\fR <file>] 8 [\fB\-c\fR <chipname>] [\fB\-m\fR [<vendor>:]<board>] \ 9 [\fB\-l\fR <file>] 10 [\fB\-i\fR <image>] [\fB\-p\fR <programmername>[:<parameters>]] etc. ??????????????????? Does that mean anything to anybody? Please, I need to flash my ASUS p5b Deluxe motherboard. What do I do? Download the BIOS version I want to use and burn it to a disc? Burn flashrom onto the same disc? I'm sure people put a lot of effort into flashrom, but it is utterly pointless if nobody can use it or you need a background in computer science, because that makes it useful to such a small group that whats the point?

2 1

FlashROM Atmel AT29C020
by Roger 09 Jan '11

09 Jan '11

As requested from flashrom output for verifying chips working. Attaching three logs detailing -Vr -Vw -VE for Atmel AT29C020 -- Roger http://rogerx.freeshell.org/

1 0

MSI 890GXM-G65 (MS-7642) Results
by KillerRex 09 Jan '11

09 Jan '11

Hello, I just successfully flashed my 890GXM-G65 board using flashrom to the latest bios (7642v18). As the board is marked as OK but untested I have kept the logs of all the steps done using -V and no other option was needed: > flashrom -V | tee noargs.txt > flashrom -Vr current.rom | tee read.txt > flashrom -Vw A7642AMS.180 | tee write.txt > flashrom -Vv A7642AMS.180 | tee verify.txt And I must mention it: it has been the smoothest bios update I've ever done... I hope it helps!

1 0

MSI K9VGM-V (MS-7253 Ver 1.0)
by chiaki 08 Jan '11

08 Jan '11

-Vw: flashrom v0.9.3-r1250 on Linux 2.6.28-11-generic (i686), built with libpci 3.0.0, GCC 4.3.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1299M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1005 us, 10000 myus = 10003 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MICRO-STAR INTERNATIONAL CO., LTD" DMI string system-product-name: "MS-7253" DMI string system-version: "1.00" DMI string baseboard-manufacturer: "MICRO-STAR INTERNATIONAL CO., LTD" DMI string baseboard-product-name: "MS-7253" DMI string baseboard-version: "1.00" DMI string chassis-type: "Desktop" Found chipset "VIA VT8237A", enabling flash write... chipset PCI ID is 1106:3337, OK. This chipset supports the following protocols: Non-SPI. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A25L05PT, 64 KB: skipped. Probing for AMIC A25L05PU, 64 KB: skipped. Probing for AMIC A25L10PT, 128 KB: skipped. Probing for AMIC A25L10PU, 128 KB: skipped. Probing for AMIC A25L20PT, 256 KB: skipped. Probing for AMIC A25L20PU, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A25L80P, 1024 KB: skipped. Probing for AMIC A25L16PT, 2048 KB: skipped. Probing for AMIC A25L16PU, 2048 KB: skipped. Probing for AMIC A25L512, 64 KB: skipped. Probing for AMIC A25L010, 128 KB: skipped. Probing for AMIC A25L020, 256 KB: skipped. Probing for AMIC A25L040, 512 KB: skipped. Probing for AMIC A25L080, 1024 KB: skipped. Probing for AMIC A25L016, 2048 KB: skipped. Probing for AMIC A25L032, 4096 KB: skipped. Probing for AMIC A25LQ032, 4096 KB: skipped. Probing for AMIC A29002B, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF081A, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25DQ161, 2048 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT49F020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Bright BM29F040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for EMST F25L008A, 1024 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x24, id2 0x2d Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x24, id2 0x2d Probing for Hyundai HY29F002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Hyundai HY29F002B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Hyundai HY29F040A, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Intel 28F001BN/BX-T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: probe_82802ab: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: probe_82802ab: id1 0x24, id2 0x2d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: probe_82802ab: id1 0x24, id2 0x2d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L1635E, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29C51000T, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29C51400B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29C51400T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29LC51000, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29LC51001, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for MoselVitelic V29LC51002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 KB: skipped. Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for Spansion S25FL032A, 4096 KB: skipped. Probing for Spansion S25FL064A, 8192 KB: skipped. Probing for SST SST25VF010.REMS, 128 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF064C, 8192 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25LF040A.RES, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Found chip "SST SST49LF040B" (512 KB, LPC) at physical address 0xfff80000. Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M25PX32, 4096 KB: skipped. Probing for ST M25PX64, 8192 KB: skipped. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 KB: probe_m29f400bt: id1 0x24, id2 0x2d Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x24, id2 0x2d Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0x10, id2 0x0c, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xe9, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x24, id2 0x73, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0xfb, id2 0xbd, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25Q64, 8192 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W29C020(C)/W29C022, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W29C040/P, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040C, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040FB, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040FC, 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W49F020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V080FA, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for AMIC unknown AMIC SPI chip, 0 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for Eon unknown Eon SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. === This flash part has status UNTESTED for operations: WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Flash image seems to be a legacy BIOS. Disabling checks. Reading old flash chip contents... Erasing and writing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff:E, 0x001000-0x001fff:E, 0x002000-0x002fff:E, 0x003000-0x003fff:E, 0x004000-0x004fff:E, 0x005000-0x005fff:E, 0x006000-0x006fff:E, 0x007000-0x007fff:E, 0x008000-0x008fff:E, 0x009000-0x009fff:E, 0x00a000-0x00afff:E, 0x00b000-0x00bfff:E, 0x00c000-0x00cfff:E, 0x00d000-0x00dfff:E, 0x00e000-0x00efff:E, 0x00f000-0x00ffff:E, 0x010000-0x010fff:E, 0x011000-0x011fff:E, 0x012000-0x012fff:E, 0x013000-0x013fff:E, 0x014000-0x014fff:E, 0x015000-0x015fff:E, 0x016000-0x016fff:E, 0x017000-0x017fff:E, 0x018000-0x018fff:E, 0x019000-0x019fff:E, 0x01a000-0x01afff:E, 0x01b000-0x01bfff:EW, 0x01c000-0x01cfff:EW, 0x01d000-0x01dfff:EW, 0x01e000-0x01efff:EW, 0x01f000-0x01ffff:EW, 0x020000-0x020fff:EW, 0x021000-0x021fff:EW, 0x022000-0x022fff:EW, 0x023000-0x023fff:EW, 0x024000-0x024fff:EW, 0x025000-0x025fff:EW, 0x026000-0x026fff:EW, 0x027000-0x027fff:EW, 0x028000-0x028fff:EW, 0x029000-0x029fff:EW, 0x02a000-0x02afff:EW, 0x02b000-0x02bfff:EW, 0x02c000-0x02cfff:EW, 0x02d000-0x02dfff:EW, 0x02e000-0x02efff:EW, 0x02f000-0x02ffff:EW, 0x030000-0x030fff:EW, 0x031000-0x031fff:EW, 0x032000-0x032fff:EW, 0x033000-0x033fff:EW, 0x034000-0x034fff:EW, 0x035000-0x035fff:EW, 0x036000-0x036fff:EW, 0x037000-0x037fff:EW, 0x038000-0x038fff:EW, 0x039000-0x039fff:EW, 0x03a000-0x03afff:EW, 0x03b000-0x03bfff:EW, 0x03c000-0x03cfff:EW, 0x03d000-0x03dfff:EW, 0x03e000-0x03efff:EW, 0x03f000-0x03ffff:EW, 0x040000-0x040fff:EW, 0x041000-0x041fff:EW, 0x042000-0x042fff:EW, 0x043000-0x043fff:EW, 0x044000-0x044fff:EW, 0x045000-0x045fff:EW, 0x046000-0x046fff:EW, 0x047000-0x047fff:EW, 0x048000-0x048fff:EW, 0x049000-0x049fff:EW, 0x04a000-0x04afff:EW, 0x04b000-0x04bfff:EW, 0x04c000-0x04cfff:EW, 0x04d000-0x04dfff:EW, 0x04e000-0x04efff:EW, 0x04f000-0x04ffff:EW, 0x050000-0x050fff:EW, 0x051000-0x051fff:EW, 0x052000-0x052fff:EW, 0x053000-0x053fff:EW, 0x054000-0x054fff:EW, 0x055000-0x055fff:EW, 0x056000-0x056fff:EW, 0x057000-0x057fff:EW, 0x058000-0x058fff:W, 0x059000-0x059fff:EW, 0x05a000-0x05afff:EW, 0x05b000-0x05bfff:EW, 0x05c000-0x05cfff:EW, 0x05d000-0x05dfff:EW, 0x05e000-0x05efff:EW, 0x05f000-0x05ffff:EW, 0x060000-0x060fff:E, 0x061000-0x061fff:E, 0x062000-0x062fff:E, 0x063000-0x063fff:E, 0x064000-0x064fff:E, 0x065000-0x065fff:E, 0x066000-0x066fff:E, 0x067000-0x067fff:E, 0x068000-0x068fff:E, 0x069000-0x069fff:E, 0x06a000-0x06afff:E, 0x06b000-0x06bfff:E, 0x06c000-0x06cfff:S, 0x06d000-0x06dfff:S, 0x06e000-0x06efff:E, 0x06f000-0x06ffff:S, 0x070000-0x070fff:EW, 0x071000-0x071fff:EW, 0x072000-0x072fff:EW, 0x073000-0x073fff:EW, 0x074000-0x074fff:EW, 0x075000-0x075fff:EW, 0x076000-0x076fff:EW, 0x077000-0x077fff:EW, 0x078000-0x078fff:EW, 0x079000-0x079fff:EW, 0x07a000-0x07afff:EW, 0x07b000-0x07bfff:EW, 0x07c000-0x07cfff:S, 0x07d000-0x07dfff:S, 0x07e000-0x07efff:EW, 0x07f000-0x07ffff:EW Done. Verifying flash... VERIFIED. Restoring PCI config space for 00:11:0 reg 0x40 Restoring PCI config space for 00:11:0 reg 0x41

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom