flashrom

flashrom@flashrom.org

8 participants
9164 discussions

[PATCH] Fix error messages regarding long options
by Stefan Tauner 09 Jan '12

09 Jan '12

Use getopt_long's flag field to distinguish short and long options where needed and name both variants if this is not sufficient. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- the const bits are not really needed, but at least they make more sense than the static modifier i hope :) option_index is used to index the long_options array hence it has to be guaranteed to be in its range. getopt_long guarantees this in the case opt == 0 afaics so we are safe. cli_classic.c | 28 +++++++++++++++++++--------- 1 files changed, 19 insertions(+), 9 deletions(-) diff --git a/cli_classic.c b/cli_classic.c index da658a6..f864b05 100644 --- a/cli_classic.c +++ b/cli_classic.c @@ -177,13 +177,15 @@ int main(int argc, char *argv[]) enum programmer prog = PROGRAMMER_INVALID; int ret = 0; - static const char optstring[] = "r:Rw:v:nVEfc:m:l:i:p:Lzh"; - static const struct option long_options[] = { + const char const optstring[] = "r:Rw:v:nVEfc:m:l:i:p:Lzh"; + int long_verify = -1; + int long_noverify = -1; + const struct option const long_options[] = { {"read", 1, NULL, 'r'}, {"write", 1, NULL, 'w'}, {"erase", 0, NULL, 'E'}, - {"verify", 1, NULL, 'v'}, - {"noverify", 0, NULL, 'n'}, + {"verify", 1, &long_verify, 'v'}, + {"noverify", 0, &long_noverify, 'n'}, {"chip", 1, NULL, 'c'}, {"verbose", 0, NULL, 'V'}, {"force", 0, NULL, 'f'}, @@ -214,6 +216,10 @@ int main(int argc, char *argv[]) */ while ((opt = getopt_long(argc, argv, optstring, long_options, &option_index)) != EOF) { + if (opt == 0) { + opt = long_options[option_index].val; + } + switch (opt) { case 'r': if (++operation_specified > 1) { @@ -241,8 +247,10 @@ int main(int argc, char *argv[]) cli_classic_abort_usage(); } if (dont_verify_it) { - fprintf(stderr, "--verify and --noverify are" - "mutually exclusive. Aborting.\n"); + fprintf(stderr, "%s and %s are " + "mutually exclusive. Aborting.\n", + long_verify != -1 ? "--verify" : "-v", + long_noverify != -1? "--noverify" : "-n"); cli_classic_abort_usage(); } filename = strdup(optarg); @@ -250,8 +258,10 @@ int main(int argc, char *argv[]) break; case 'n': if (verify_it) { - fprintf(stderr, "--verify and --noverify are" - "mutually exclusive. Aborting.\n"); + fprintf(stderr, "%s and %s are " + "mutually exclusive. Aborting.\n", + long_verify != -1 ? "--verify" : "-v", + long_noverify != -1? "--noverify" : "-n"); cli_classic_abort_usage(); } dont_verify_it = 1; @@ -310,7 +320,7 @@ int main(int argc, char *argv[]) break; case 'p': if (prog != PROGRAMMER_INVALID) { - fprintf(stderr, "Error: --programmer specified " + fprintf(stderr, "Error: --programmer/-p specified " "more than once. You can separate " "multiple\nparameters for a programmer " "with \",\". Please see the man page " -- 1.7.1

1 0

Re: [flashrom] flashrom -V
by Stefan Tauner 09 Jan '12

09 Jan '12

On Mon, 9 Jan 2012 22:40:53 +0100 Luc Chante <luc.chante(a)gmail.com> wrote: > flashrom v0.9.4-r1455 on Linux 2.6.32-220.2.1.el6.centos.plus.x86_64 (x86_64), built with libpci 3.1.4, GCC 4.4.5 20110214 (Red Hat 4.4.5-6), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 2912M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1000 us, 10000 myus = 9986 us, 4 myus = 5 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "System manufacturer" > DMI string system-product-name: "System Product Name" > DMI string system-version: "System Version" > DMI string baseboard-manufacturer: "ASUSTeK Computer INC." > DMI string baseboard-product-name: "P5N7A-VM" > DMI string baseboard-version: "Rev 1.xx" > DMI string chassis-type: "Desktop" > Found chipset "NVIDIA MCP79" with PCI ID 10de:0aac. > This chipset is marked as untested. If you are using an up-to-date version > of flashrom please email a report to flashrom(a)flashrom.org including a > verbose (-V) log. Thank you! > Enabling flash write... This chipset is not really supported yet. Guesswork... > ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 > Flash bus type is SPI > SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! > Found SMBus device 10de:0aa2 at 00:03:2 > MCP SPI BAR is at 0xf9f80000 > SPI control is 0xc052, req=0, gnt=0 > Please send the output of "flashrom -V" to flashrom(a)flashrom.org with > your board name: flashrom -V as the subject to help us finish support for your > chipset. Thanks. > OK. > This chipset supports the following protocols: SPI. > […] > Found Winbond flash chip "W25X80" (1024 kB, SPI). > No operations were specified. Hello Luc, thanks for your report! I have marked the chipset and mainboard as tested and will commit that later together with other small changes. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

flashrom output
by Armin 09 Jan '12

09 Jan '12

Hello, I've flashed sucessfully a ASUS M2A-VM HDMI Mainboard. Here is the output: $ sudo flashrom -Vw 2302.BIN flashrom v0.9.4-r1394 on Linux 3.0.0-14-generic (x86_64), built with libpci 3.1.7, GCC 4.6.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 666M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1011 us, 10000 myus = 10013 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2A-VM HDMI" DMI string baseboard-version: "1.XX " DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8716 on port 0x2e Found chipset "AMD SB600" with PCI ID 1002:438d. Enabling flash write... SPI base address is at 0x0 ROM strap override is not active OK. This chipset supports the following protocols: LPC, FWH. No IT87* serial flash segment enabled. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xf8, id2 0x0d, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xf8, id2 0x0d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xf8, id2 0x0d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xf8, id2 0x0d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xf8, id2 0x0d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Found Winbond flash chip "W39V080A" (1024 kB, LPC) at physical address 0xfff00000. Lockout bits: Hardware bootblock locking (#TBL) is not active. Hardware remaining chip locking (#WP) is not active.. Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x00ffff:S, 0x010000-0x01ffff:EW, 0x020000-0x02ffff:E, 0x030000-0x03ffff:EW, 0x040000-0x04ffff:EW, 0x050000-0x05ffff:EW, 0x060000-0x06ffff:EW, 0x070000-0x07ffff:EW, 0x080000-0x08ffff:EW, 0x090000-0x09ffff:W, 0x0a0000-0x0affff:W, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:W, 0x0e0000-0x0effff:EW, 0x0f0000-0x0fffff:EW Erase/write done. Verifying flash... VERIFIED. $ sudo flashrom -Vr old_bios.BIN flashrom v0.9.4-r1394 on Linux 3.0.0-14-generic (x86_64), built with libpci 3.1.7, GCC 4.6.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 2 usecs, 664M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 997 us, 10000 myus = 10067 us, 8 myus = 9 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2A-VM HDMI" DMI string baseboard-version: "1.XX " DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8716 on port 0x2e Found chipset "AMD SB600" with PCI ID 1002:438d. Enabling flash write... SPI base address is at 0x0 ROM strap override is not active OK. This chipset supports the following protocols: LPC, FWH. No IT87* serial flash segment enabled. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Found Winbond flash chip "W39V080A" (1024 kB, LPC) at physical address 0xfff00000. Lockout bits: Hardware bootblock locking (#TBL) is not active. Hardware remaining chip locking (#WP) is not active.. Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... done. $ sudo flashrom -V flashrom v0.9.4-r1394 on Linux 3.0.0-14-generic (x86_64), built with libpci 3.1.7, GCC 4.6.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 665M loops per second, 10 myus = 12 us, 100 myus = 101 us, 1000 myus = 1010 us, 10000 myus = 10009 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2A-VM HDMI" DMI string baseboard-version: "1.XX " DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8716 on port 0x2e Found chipset "AMD SB600" with PCI ID 1002:438d. Enabling flash write... SPI base address is at 0x0 ROM strap override is not active OK. This chipset supports the following protocols: LPC, FWH. No IT87* serial flash segment enabled. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xda, id2 0xd0 Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x75, id2 0x91, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xaa, id2 0xbb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Found Winbond flash chip "W39V080A" (1024 kB, LPC) at physical address 0xfff00000. Lockout bits: Hardware bootblock locking (#TBL) is not active. Hardware remaining chip locking (#WP) is not active.. Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xda, id2 0xd0 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xda, id2 0xd0 === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified. Cheers and thanks for writing flashrom Armin

2 1

X8DTT-H
by Jimmie Tauriainen 09 Jan '12

09 Jan '12

Hi, This is a Supermicro X8DTT-HIBQF but it uses the same BIOS as X8DTT-H as refered in DMI. Probably all H8DTT* boards uses same. Anyway attaching flashrom -V outputs. root@spts-10-143:~/flashrom# dmidecode -t baseboard # dmidecode 2.9 SMBIOS 2.6 present. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8DTT-H Version: 2.0 Serial Number: 1234567890 Asset Tag: 1234567890 Features: Board is a hosting board Board is replaceable Location In Chassis: 1234567890 Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Best regards, Jimmie

4 5

flashrom -V
by Luc Chante 09 Jan '12

09 Jan '12

missing files

1 0

flashrom -V
by Luc Chante 09 Jan '12

09 Jan '12

MB : Asus P5N7A-VM old bios vers. : 512 new bios vers. : 519 # flashrom flashrom v0.9.4-r1455 on Linux 2.6.32-220.2.1.el6.centos.plus.x86_64 (x86_64), built with libpci 3.1.4, GCC 4.4.5 20110214 (Red Hat 4.4.5-6), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "NVIDIA MCP79". This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Mapping NVIDIA MCP6x SPI at 0xf9f80000, unaligned size 0x544. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. This chipset supports the following protocols: SPI. Found Winbond flash chip "W25X80" (1024 kB, SPI) at physical address 0xfff00000. No operations were specified. Saving old ROM : Succed Writind new ROM : Succed (no reboot now) After rebooting it works just fine. Thx for flashrom utility.

1 0

Re: [flashrom] Help: unable to upgrade bios
by Raghuramchary Jallipalli 09 Jan '12

09 Jan '12

Thanks David. As you said, the reason for not programming is due to wrong op.atomic configuration. Is there any way to set these properly? Yes jumper selects the ROM at a time. Thanks for the help, Raghu From: David Hendricks [mailto:dhendrix@google.com] Sent: Saturday, January 07, 2012 4:42 AM To: Raghuramchary Jallipalli Cc: flashrom(a)flashrom.org; V Balaji; Vishnuvardhan Reddy Subject: Re: [flashrom] Help: unable to upgrade bios On Fri, Jan 6, 2012 at 5:12 AM, Raghuramchary Jallipalli <Raghuramchary.Jallipalli(a)lntinfotech.com<mailto:Raghuramchary.Jallipalli@lntinfotech.com>> wrote: The force option enable worked and we were able to program the AT25DF321A flash. But the contents are wrong and the board was not able to come up. Please see attached for the verbose output for both read and write. There is a high likelihood that either the Management Engine (ME) or embedded controller (EC) is interfering with Flashrom operation. One concern is that flashrom does not appear to set the op.atomic field properly: 0x94: 0x0606 (PREOP) 0x96: 0x0be4 (OPTYPE) 0x98: 0x02030105 (OPMENU) 0x9C: 0xff9f3c20 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xD0: 0x00000000 (FPB) Reading OPCODES... done preop0=0x06, preop1=0x06 op[0]=0x05, 0, 0 op[1]=0x01, 1, 0 op[2]=0x03, 2, 0 op[3]=0x02, 3, 0 op[4]=0x20, 3, 0 op[5]=0x3c, 2, 0 op[6]=0x9f, 0, 0 op[7]=0xff, 0, 0 The third column shows that none of the opcodes are configured as atomic cycles. Thus, Flashrom does not know to set the SPIC_ACS bit (http://flashrom.org/trac/flashrom/browser/trunk/ichspi.c#L782) when processing these opcodes. If the "atomic" field is not set properly, then it is possible for ME or EC to interfere with flashrom in between write enable (WREN) opcodes such as block erase and program page. On Fri, Jan 6, 2012 at 5:12 AM, Raghuramchary Jallipalli <Raghuramchary.Jallipalli(a)lntinfotech.com<mailto:Raghuramchary.Jallipalli@lntinfotech.com>> wrote: For your info, the board has two flashes(each 4MB) and the bios resides on the second(we have a jumper option to select the flash device). We are confused whether the flashrom selects the correct flash device and program it. Are both ROMs logically present? Or will the jumper only enable one ROM at a given time? If there are multiple ROMs present, then Flashrom use the "Hardware Sequencing" method of flashing when it detects the "Number of Components" (NC) > 0 in the flash descriptor region: http://flashrom.org/trac/flashrom/browser/trunk/ichspi.c#L1742 See FLMAP0 in the Intel documentation for more details, and ensure the NC field is programmed appropriately for your mainboard configuration. -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc. ________________________________ The contents of this e-mail and any attachment(s) may contain confidential or privileged information for the intended recipient(s). Unintended recipients are prohibited from taking action on the basis of information in this e-mail and using or disseminating the information, and must notify the sender and delete it from their system. L&T Infotech will not accept responsibility or liability for the accuracy or completeness of, or the presence of any virus or disabling code in this e-mail" ************************************************************************* This email and attachments have been scanned for potential proprietary or sensitive information leakage. Websense Data Security, Protecting Your Information from the Inside Out. www.websense.com *************************************************************************

1 0

Re: [flashrom] I lost my backup image and now my pc doesn't start...!
by Marcos Felipe Rasia de Mello 08 Jan '12

08 Jan '12

2012/1/8 İlhan Kahraman <ilhan805(a)gmail.com>: > No, it didn't give any errors. And No, bupdater identifies the bios of > m4a.... and gives an error mesage because it knows the board is not > appropriate for the bios of m4a.... So I have to do it with flashrom. > Yes I can do hot swap as I mention in prev. mail. Same protocol same > voltages... > > The one thing that I totally confused that: the flashing. Is it just a " > sudo flashrom -w any.rom " process or more complicated than that like: > updating some part of the chip with -- layout or -- image options > and leaving other parts of the chip whit its original contents (like boot > block) or something like that? And I do not really know if this process can > affect the amd chipset of my board or its only effective on the flash chip? > İf its just a writing process of any .ROM file I thing I can try forcing it > to writing operation with internal programer... > > Thanks for Luck :)) > flashrom doesn't identifies what is bootblock/mainblock/whatever nor check if the board model matches like the official tools generally do. It's a low level tool that put inside the flash chip exactly the same contents of the the image file. Nothing else. By default flashrom uses the internal programmer and just touch the mainboard flash chip. It's really "flashrom -w" (-Vw for the reports :-) you need. About the bupdater, maybe there's an option to make it ignore the board mismatch (can be undocumented...). afudos and awdflash have it AFAIK. Did you tried bupdater with "/pc /g"? I couldn't find what they are for, but worth testing. Marcos

1 0

(no subject)
by Андрей Пацан 08 Jan '12

08 Jan '12

motherboard : ASRock N68C-GS UCC,Cipset : GeForce 7025 / nForce 630a sudo flashrom -V flashrom v0.9.4-r1395 on Linux 3.1.7-1-ARCH (x86_64), built with libpci 3.1.8, GCC 4.6.2, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1507M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 2536 us, 10000 myus = 10007 us, 4 myus = 14 us, OK. Initializing internal programmer No coreboot table found. sh: dmidecode: команда не найдена dmidecode execution unsuccessful - continuing without DMI info Found chipset "NVIDIA MCP61" with PCI ID 10de:03e1. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Flash bus type is SPI SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 Mapping NVIDIA MCP6x SPI at 0xfec80000, unaligned size 0x544. SPI control is 0x0002, req=0, gnt=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. WARNING: unexpected second chipset match: "NVIDIA MCP61" ignoring, please report lspci and board URL to flashrom(a)flashrom.org with 'CHIPSET: your board name' in the subject line. This chipset supports the following protocols: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L8005" (1024 kB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF010.REMS, 128 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A.RES, 512 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x13 No operations were specified.

1 0

MSI K9N6GM-v : flashrom -V
by Frederic Louard 08 Jan '12

08 Jan '12

[root@pollux ~]# flashrom -V flashrom v0.9.4-r1455 on Linux 3.1.6-1.fc16.x86_64 (x86_64), built with libpci 3.1.7, GCC 4.6.1 20111003 (Red Hat 4.6.1-10), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 866M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1002 us, 10000 myus = 10007 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MSI" DMI string system-product-name: "MS-7309" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "MSI" DMI string baseboard-product-name: "MS-7309" DMI string baseboard-version: "1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. This chipset supports the following protocols: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xa1, id2 0x6e, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xa1, id2 0x6e, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xa1, id2 0x6e, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xa1, id2 0x6e, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xa1, id2 0x6e, id1 is normal flash content, id2 is normal flash content No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88 Thanks.

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom