- flashrom - mail.coreboot.org

W836xx: Vico : flashrom -V
by Siniša R. 25 Nov '12

25 Nov '12

flashrom v0.9.6.1-r1563 on Linux 3.5.0-19-generic (i686) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 2 usecs, 1728M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 998 us, 10000 myus = 14494 us, 8 myus = 9 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Acer, inc." DMI string system-product-name: "TravelMate 6231 " DMI string system-version: "Not Applicable" DMI string baseboard-manufacturer: "Acer, Inc." DMI string baseboard-product-name: "Vico " DMI string baseboard-version: "Not Applicable" DMI string chassis-type: "Other" DMI chassis-type is not specific enough. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: fc. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. ======================================================================== WARNING! You may be running flashrom on an unsupported laptop. We could not detect this for sure because your vendor has not setup the SMBIOS tables correctly. You can enforce execution by adding '-p internal:laptop=this_is_not_a_laptop' to the command line, but please read the following warning if you are not sure. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. Error: Programmer initialization failed.

1 0

flashrom -V
by nicolas gras 24 Nov '12

24 Nov '12

flashrom v0.9.5.2-r1517 on Linux 3.2.0-24-generic (x86_64), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 869M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10072 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2N-MX SE Plus" DMI string baseboard-version: "Rev x.xx" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Flash bus type is SPI SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 SPI control is 0x0002, req=0, gnt=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L8005" (1024 kB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x13 Found Macronix flash chip "MX25L8005" (1024 kB, SPI). No operations were specified.

1 0

Re: [flashrom] [PATCH] Enable VX855 chipset
by Stefan Tauner 24 Nov '12

24 Nov '12

On Sat, 20 Oct 2012 23:31:52 -0400 John Schmerge <jbschmerge(a)gmail.com> wrote: > Hi Stefan, i'm sorry for the rather slow response, i've been taking > some time away from everything tech related. Someone you may wish to > reach out to to ask about this is Ian Geiser at Devon IT (my former > employer)... His email address is igeiser(a)devonit.com Hello Ian, is Devon still using flashrom with (newer) VIA chipsets? We have included a number of improvements/support for additional models in r1578*, but were not able to test them on real hardware but VX900 with SPI. If you have access to affected boards, we would be glad if you could at least run some probing runs (and send us the output). * http://flashrom.org/trac/flashrom/changeset/1578/trunk -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] [PATCH] Improve --help and friends.
by Paul Menzel 24 Nov '12

24 Nov '12

Am Samstag, den 24.11.2012, 18:44 +0100 schrieb Stefan Tauner: > More clear "variable" names, better explanation if now programmer is selected etc. s,now,no, > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > --- > cli_classic.c | 78 +++++++++++++++++++++++++-------------------------------- > flashrom.c | 1 - > print.c | 1 + > 3 files changed, 35 insertions(+), 45 deletions(-) > > diff --git a/cli_classic.c b/cli_classic.c > index ccf75e9..0d28d15 100644 > --- a/cli_classic.c > +++ b/cli_classic.c > @@ -33,58 +33,42 @@ > > static void cli_classic_usage(const char *name) > { > - printf("Usage: flashrom [-h|-R|-L|" > + printf("Please note that the command line interface for flashrom has changed between\n" > + "0.9.5 and 0.9.6 and will change again before flashrom 1.0.\n\n"); > + > + printf("Usage: %s [-h|-R|-L|" > #if CONFIG_PRINT_WIKI == 1 > - "-z|" > + "-z|" Indentation is changed? > #endif […] I quickly looked over it and could not find any suspicious. It is hard though as there are a lot of white space changes. Acked-by: Paul Menzel <paulepanter(a)users.sourceforge.net> Thanks, Paul

2 1

[commit] r1624 - trunk
by repository service 24 Nov '12

24 Nov '12

Author: stefanct Date: Sat Nov 24 19:59:39 2012 New Revision: 1624 URL: http://flashrom.org/trac/flashrom/changeset/1624 Log: Improve --help and friends. More clear "variable" names, better explanation if no programmer is selected etc. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Paul Menzel <paulepanter(a)users.sourceforge.net> Modified: trunk/cli_classic.c trunk/flashrom.c trunk/print.c Modified: trunk/cli_classic.c ============================================================================== --- trunk/cli_classic.c Tue Nov 20 22:06:16 2012 (r1623) +++ trunk/cli_classic.c Sat Nov 24 19:59:39 2012 (r1624) @@ -33,58 +33,42 @@ static void cli_classic_usage(const char *name) { - printf("Usage: flashrom [-h|-R|-L|" + printf("Please note that the command line interface for flashrom has changed between\n" + "0.9.5 and 0.9.6 and will change again before flashrom 1.0.\n\n"); + + printf("Usage: %s [-h|-R|-L|" #if CONFIG_PRINT_WIKI == 1 - "-z|" + "-z|" #endif - "-p <programmername>[:<parameters>]\n" - " [-E|-r <file>|-w <file>|-v <file>] [-c <chipname>]\n" - " [-l <file> [-i <image>]] [-n] [-f]]\n" - " [-V[V[V]]] [-o <logfile>]\n\n"); - - printf("Please note that the command line interface for flashrom has " - "changed between\n" - "0.9.5 and 0.9.6 and will change again before flashrom 1.0.\n" - "Do not use flashrom in scripts or other automated tools " - "without checking\n" - "that your flashrom version won't interpret options in a " - "different way.\n\n"); - - printf(" -h | --help print this help text\n" - " -R | --version print version (release)\n" - " -r | --read <file> read flash and save to " - "<file>\n" - " -w | --write <file> write <file> to flash\n" - " -v | --verify <file> verify flash against " - "<file>\n" - " -E | --erase erase flash device\n" - " -V | --verbose more verbose output\n" - " -c | --chip <chipname> probe only for specified " - "flash chip\n" - " -f | --force force specific operations " - "(see man page)\n" - " -n | --noverify don't auto-verify\n" - " -l | --layout <file> read ROM layout from " - "<file>\n" - " -i | --image <name> only flash image <name> " - "from flash layout\n" - " -o | --output <name> log to file <name>\n" - " -L | --list-supported print supported devices\n" + "-p <programmername>[:<parameters>] [-c <chipname>]\n" + "[-E|(-r|-w|-v) <file>] [-l <layoutfile> [-i <imagename>]...] [-n] [-f]]\n" + "[-V[V[V]]] [-o <logfile>]\n\n", name); + + printf(" -h | --help print this help text\n" + " -R | --version print version (release)\n" + " -r | --read <file> read flash and save to <file>\n" + " -w | --write <file> write <file> to flash\n" + " -v | --verify <file> verify flash against <file>\n" + " -E | --erase erase flash memory\n" + " -V | --verbose more verbose output\n" + " -c | --chip <chipname> probe only for specified flash chip\n" + " -f | --force force specific operations (see man page)\n" + " -n | --noverify don't auto-verify\n" + " -l | --layout <layoutfile> read ROM layout from <layoutfile>\n" + " -i | --image <name> only flash image <name> from flash layout\n" + " -o | --output <logfile> log output to <logfile>\n" + " -L | --list-supported print supported devices\n" #if CONFIG_PRINT_WIKI == 1 - " -z | --list-supported-wiki print supported devices " - "in wiki syntax\n" + " -z | --list-supported-wiki print supported devices in wiki syntax\n" #endif - " -p | --programmer <name>[:<param>] specify the programmer " - "device\n"); - - list_programmers_linebreak(37, 80, 1); - printf("\nYou can specify one of -h, -R, -L, " + " -p | --programmer <name>[:<param>] specify the programmer device. One of\n"); + list_programmers_linebreak(4, 80, 0); + printf(".\n\nYou can specify one of -h, -R, -L, " #if CONFIG_PRINT_WIKI == 1 "-z, " #endif "-E, -r, -w, -v or no operation.\n" - "If no operation is specified, flashrom will only probe for " - "flash chips.\n\n"); + "If no operation is specified, flashrom will only probe for flash chips.\n"); } static void cli_classic_abort_usage(void) @@ -296,6 +280,7 @@ fprintf(stderr, "Error: Unknown programmer \"%s\". Valid choices are:\n", optarg); list_programmers_linebreak(0, 80, 0); + msg_ginfo(".\n"); cli_classic_abort_usage(); } break; @@ -407,8 +392,13 @@ programmer_table[CONFIG_DEFAULT_PROGRAMMER].name); } else { msg_perr("Please select a programmer with the --programmer parameter.\n" + "Previously this was not necessary because there was a default set.\n" +#if CONFIG_INTERNAL == 1 + "To choose the mainboard of this computer use 'internal'. " +#endif "Valid choices are:\n"); list_programmers_linebreak(0, 80, 0); + msg_ginfo(".\n"); ret = 1; goto out; } Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Tue Nov 20 22:06:16 2012 (r1623) +++ trunk/flashrom.c Sat Nov 24 19:59:39 2012 (r1624) @@ -1461,7 +1461,6 @@ } else { if (paren) msg_ginfo(")"); - msg_ginfo("\n"); } } } Modified: trunk/print.c ============================================================================== --- trunk/print.c Tue Nov 20 22:06:16 2012 (r1623) +++ trunk/print.c Sat Nov 24 19:59:39 2012 (r1624) @@ -440,6 +440,7 @@ msg_ginfo("\nSupported programmers:\n"); list_programmers_linebreak(0, 80, 0); + msg_ginfo("\n"); #if CONFIG_INTERNAL == 1 msg_ginfo("\nSupported devices for the %s programmer:\n\n", programmer_table[PROGRAMMER_INTERNAL].name);

1 0

[PATCH] Improve --help and friends.
by Stefan Tauner 24 Nov '12

24 Nov '12

More clear "variable" names, better explanation if now programmer is selected etc. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- cli_classic.c | 78 +++++++++++++++++++++++++-------------------------------- flashrom.c | 1 - print.c | 1 + 3 files changed, 35 insertions(+), 45 deletions(-) diff --git a/cli_classic.c b/cli_classic.c index ccf75e9..0d28d15 100644 --- a/cli_classic.c +++ b/cli_classic.c @@ -33,58 +33,42 @@ static void cli_classic_usage(const char *name) { - printf("Usage: flashrom [-h|-R|-L|" + printf("Please note that the command line interface for flashrom has changed between\n" + "0.9.5 and 0.9.6 and will change again before flashrom 1.0.\n\n"); + + printf("Usage: %s [-h|-R|-L|" #if CONFIG_PRINT_WIKI == 1 - "-z|" + "-z|" #endif - "-p <programmername>[:<parameters>]\n" - " [-E|-r <file>|-w <file>|-v <file>] [-c <chipname>]\n" - " [-l <file> [-i <image>]] [-n] [-f]]\n" - " [-V[V[V]]] [-o <logfile>]\n\n"); - - printf("Please note that the command line interface for flashrom has " - "changed between\n" - "0.9.5 and 0.9.6 and will change again before flashrom 1.0.\n" - "Do not use flashrom in scripts or other automated tools " - "without checking\n" - "that your flashrom version won't interpret options in a " - "different way.\n\n"); - - printf(" -h | --help print this help text\n" - " -R | --version print version (release)\n" - " -r | --read <file> read flash and save to " - "<file>\n" - " -w | --write <file> write <file> to flash\n" - " -v | --verify <file> verify flash against " - "<file>\n" - " -E | --erase erase flash device\n" - " -V | --verbose more verbose output\n" - " -c | --chip <chipname> probe only for specified " - "flash chip\n" - " -f | --force force specific operations " - "(see man page)\n" - " -n | --noverify don't auto-verify\n" - " -l | --layout <file> read ROM layout from " - "<file>\n" - " -i | --image <name> only flash image <name> " - "from flash layout\n" - " -o | --output <name> log to file <name>\n" - " -L | --list-supported print supported devices\n" + "-p <programmername>[:<parameters>] [-c <chipname>]\n" + "[-E|(-r|-w|-v) <imagefile>] [-l <layoutfile> [-i <imagename>]...] [-n] [-f]]\n" + "[-V[V[V]]] [-o <logfile>]\n\n", name); + + printf(" -h | --help print this help text\n" + " -R | --version print version (release)\n" + " -r | --read <imagefile> read flash and save to <imagefile>\n" + " -w | --write <imagefile> write <imagefile> to flash\n" + " -v | --verify <imagefile> verify flash against <imagefile>\n" + " -E | --erase erase flash memory\n" + " -V | --verbose more verbose output\n" + " -c | --chip <chipname> probe only for specified flash chip\n" + " -f | --force force specific operations (see man page)\n" + " -n | --noverify don't auto-verify\n" + " -l | --layout <layoutfile> read ROM layout from <layoutfile>\n" + " -i | --image <name> only flash image <name> from flash layout\n" + " -o | --output <logfile> log output to <logfile>\n" + " -L | --list-supported print supported devices\n" #if CONFIG_PRINT_WIKI == 1 - " -z | --list-supported-wiki print supported devices " - "in wiki syntax\n" + " -z | --list-supported-wiki print supported devices in wiki syntax\n" #endif - " -p | --programmer <name>[:<param>] specify the programmer " - "device\n"); - - list_programmers_linebreak(37, 80, 1); - printf("\nYou can specify one of -h, -R, -L, " + " -p | --programmer <name>[:<param>] specify the programmer device. One of\n"); + list_programmers_linebreak(4, 80, 0); + printf(".\n\nYou can specify one of -h, -R, -L, " #if CONFIG_PRINT_WIKI == 1 "-z, " #endif "-E, -r, -w, -v or no operation.\n" - "If no operation is specified, flashrom will only probe for " - "flash chips.\n\n"); + "If no operation is specified, flashrom will only probe for flash chips.\n"); } static void cli_classic_abort_usage(void) @@ -296,6 +280,7 @@ int main(int argc, char *argv[]) fprintf(stderr, "Error: Unknown programmer \"%s\". Valid choices are:\n", optarg); list_programmers_linebreak(0, 80, 0); + msg_ginfo(".\n"); cli_classic_abort_usage(); } break; @@ -407,8 +392,13 @@ int main(int argc, char *argv[]) programmer_table[CONFIG_DEFAULT_PROGRAMMER].name); } else { msg_perr("Please select a programmer with the --programmer parameter.\n" + "Previously this was not necessary because there was a default set.\n" +#if CONFIG_INTERNAL == 1 + "To choose the mainboard of this computer use 'internal'. " +#endif "Valid choices are:\n"); list_programmers_linebreak(0, 80, 0); + msg_ginfo(".\n"); ret = 1; goto out; } diff --git a/flashrom.c b/flashrom.c index 2299b06..e2ad170 100644 --- a/flashrom.c +++ b/flashrom.c @@ -1461,7 +1461,6 @@ void list_programmers_linebreak(int startcol, int cols, int paren) } else { if (paren) msg_ginfo(")"); - msg_ginfo("\n"); } } } diff --git a/print.c b/print.c index d7bdbfe..5f6ae43 100644 --- a/print.c +++ b/print.c @@ -440,6 +440,7 @@ int print_supported(void) msg_ginfo("\nSupported programmers:\n"); list_programmers_linebreak(0, 80, 0); + msg_ginfo("\n"); #if CONFIG_INTERNAL == 1 msg_ginfo("\nSupported devices for the %s programmer:\n\n", programmer_table[PROGRAMMER_INTERNAL].name); -- Kind regards, Stefan Tauner

1 0

Supermicro X9DRT-HF+
by Jason Wolfe 24 Nov '12

24 Nov '12

This looks to be the same Intel X79 chip from the info submitted on Sep 10th in the 'Supermicro X9QRi-F+' email ( http://www.flashrom.org/pipermail/flashrom/2012-September/009887.html) , but in the interest of documentation I figured I'd submit this report from a Supermicro X9DRT-HF+ also. Any movement on support for this chip since that initial report? Thanks for all your work! flashrom v0.9.6.1-r1564 on FreeBSD 8.3-RELEASE-p4 (amd64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.2.2 20070831 prerelease [FreeBSD], little endian Command line (5 args): ./flashrom -VV -p internal -r backup.bin Calibrating delay loop... OS timer resolution is 1 usecs, 2340M loops per second, 10 myus = 10 us, 100 myus = 124 us, 1000 myus = 1174 us, 10000 myus = 10541 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Supermicro" DMI string system-product-name: "X9DRT-HF+" DMI string system-version: "0123456789" DMI string baseboard-manufacturer: "Supermicro" DMI string baseboard-product-name: "X9DRT-HF+" DMI string baseboard-version: "1.02" DMI string chassis-type: "Desktop" Found chipset "Intel X79" with PCI ID 8086:1d41. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2a WARNING: BIOS region SMM protection is enabled! Root Complex Register Block address = 0xfed1c000 GCS = 0xc01: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6018 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=3, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00020000 (FADDR) 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x000f0000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x0000ffff) is read-only. 0x58: 0x0fff0400 FREG1: BIOS region (0x00400000-0x00ffffff) is read-write. 0x5C: 0x03ff0020 FREG2: WARNING: Management Engine region (0x00020000-0x003fffff) is locked. 0x60: 0x00000fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x001f0010 FREG4: Platform Data region (0x00010000-0x0001ffff) is read-write. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x0000d807 (LVSCC) LVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8, VCL=0 0xC8: 0x0000d807 (UVSCC) UVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040003 FLMAP1 0x12100206 FLMAP2 0x00210020 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 0 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x24900025 FLILL 0x00000000 --- Details --- Component 1 density: 16 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 50 MHz Write and Erase Clock Freq.: 50 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz No forbidden opcodes. === Region Section === FLREG0 0x000f0000 FLREG1 0x0fff0400 FLREG2 0x03ff0020 FLREG3 0x00000fff FLREG4 0x001f0010 --- Details --- Region 0 (Descr.) 0x00000000 - 0x0000ffff Region 1 (BIOS ) 0x00400000 - 0x00ffffff Region 2 (ME ) 0x00020000 - 0x003fffff Region 3 (GbE ) is unused. Region 4 (Platf.) 0x00010000 - 0x0001ffff === Master Section === FLMSTR1 0x1a1b0000 FLMSTR2 0x04050000 FLMSTR3 0x08090118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw rw ME r rw GbE r rw SPI Read Configuration: prefetching enabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 SFDP revision = 1.0 SFDP number of parameter headers is 1 (NPH = 0). SFDP parameter table header 0/0: ID 0x00, version 1.0 Length 36 B, Parameter Table Pointer 0x000030 Parsing JEDEC flash parameter table... 3-Byte only addressing. Status register is non-volatile and the standard does not allow vendors to tell us whether EWSR/WREN is needed for status register writes - assuming EWSR. Write chunk size is at least 64 B. Flash chip size is 16384 kB. Block eraser 0: 4096 x 4096 B with opcode 0x20 Tried to add a duplicate block eraser: 4096 x 4096 B with opcode 0x20. Block eraser 1: 256 x 65536 B with opcode 0xd8 done. === SFDP has autodetected a flash chip which is not natively supported by flashrom yet. All standard operations (read, verify, erase and write) should work, but to support all possible features we need to add them manually. You can help us by mailing us the output of the following command to flashrom(a)flashrom.org: 'flashrom -VV [plus the -p/--programmer parameter (if needed)]' Thanks for your help! === Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI) at physical address 0x0. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI). Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x020000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0x80058e8a0 Restoring MMIO space at 0x80058e89c Restoring MMIO space at 0x80058e898 Restoring MMIO space at 0x80058e896 Restoring MMIO space at 0x80058e894 Restoring PCI config space for 00:1f:0 reg 0xdc Jason

2 1

Re: [flashrom] Need help using Flashrom
by Stefan Tauner 24 Nov '12

24 Nov '12

On Tue, 20 Nov 2012 08:35:19 -0400 "Chea Gittens - IT Specialist" <chea.gittens(a)cgtechinnovations.com> wrote: > Hi, > I upgraded the BIOS of a Biostar H61MGC motherboard to latest version > available on the Biostar website - H61NR709.BSS after I was getting issues > with the onboard VGA graphics. I used the flash utility on the motherboard > and that reported as successful. However windows 7 would not start it > freezes at the logo screen. I cannot get windows 7 boot DVD to start either > it also freezes at the logo screen. I was also not able to start Mini > Windows XP on a Hiren's Boot CD. I am also unable to start the live CDs disk > Parted Magic or SystemRescueCD. Also none of the USB ports work. I was able > to start DOS from a FAT32 formatted SATA Hard Drive. I tried to use various > DOS Bios Flash tools to flash the bios to a pervious version, however I am > getting errors about the bios being write protected. I am currently trying > to use flashrom but I would like to get some advice on how to proceed so as > to not cause further problems. I tried to do a read and save of the bios and > got the follow output: > […] > 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region > (0x00000000-0x00000fff) is read-only. > > 0x58: 0x03ff0200 FREG1: BIOS region (0x00200000-0x003fffff) is read-write. > > 0x5C: 0x01ff0001 FREG2: WARNING: Management Engine region > (0x00001000-0x001fffff) is locked. > […] > Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). > > Read operation failed! Hello Chea, the problem is the locked ME region as quoted above. We are working on unlocking it, but intel does not provide us any documentation so please do not expect a solution soon (or ever). I have added the board to our list of (un)supported boards (with an appropriate note) and will commit that later together with other small changes. That was my standard reply in cases where there is no harm done yet (by flashrom or a vendor tool), but it is not complete: flashrom might still be able to help you. The safest way (and often also the fastest, if you are prepared already) to handle such cases is to use an external programmer, i.e. a device that is attached to another PC and connected to the flash chip via cables, see http://flashrom.org/ISP If you happen to have some embedded board (e.g. an Arduino) laying around this would be an option. Also, flashrom IS able to write to the BIOS* region of the flash chip. You can think of those regions as partitions like on normal storage devices. Their layout and access restrictions are defined by the descriptor region in the first 4kB of the flash memory. The Management Engine is an embedded microcontroller in the chipset of the mainboard and its firmware is stored together with the BIOS in the flash chip (in its own region which is write and read protected as seen in the log). The main problem for us is that there is no public documentation on how the different ME versions interact with the BIOS. We believe that the ME firmware can not be updated after an operating system has booted (i.e. only the BIOS itself can flash it similarly as it can update its own firmware as you have tried). If that is correct it should be possible to update the BIOS region only with flashrom after preparing the image and applying some patches to flashrom which have not been merged yet with our main branch. We can help you with that if you want to try, but we can not guarantee you that you will be successful and eventually you could be forced to get an external programmer anyway. Since you were able to boot DOS the BIOS can not be completely broken and so the on-board flash tool should still be working (as good or bad :) as before. Maybe you should try to flash another BIOS version with that first. I hope that i could make everything clear and that this will help you. If you have further questions feel free to mail again or join our IRC channel. * actually there is probably no BIOS, but an UEFI firmware, but let's not get distracted by notations. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

(no subject)
by Keith Hui 21 Nov '12

21 Nov '12

http://www.3zscandy.com/wp-content/plugins/mywork.php?jacob954.php

1 0

[PATCH] Explicitly detect libusb-0.1 in the Makefile
by Carl-Daniel Hailfinger 20 Nov '12

20 Nov '12

Explicitly detect libusb-0.1 in the Makefile Avoid funny interactions between libpci and libusb detection. Leave libftdi autodetection alone for now. Tested on Linux, needs tests on *BSD and preferably OSX/Windows. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-libusb0_Makefile/Makefile =================================================================== --- flashrom-libusb0_Makefile/Makefile (Revision 1622) +++ flashrom-libusb0_Makefile/Makefile (Arbeitskopie) @@ -480,6 +480,8 @@ FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") PROGRAMMER_OBJS += ft2232_spi.o +# We can't set NEED_USB here because that would transform libftdi auto-enabling +# into a hard requirement for libusb, defeating the purpose of auto-enabling. endif ifeq ($(CONFIG_DUMMY), yes) @@ -531,8 +533,8 @@ ifeq ($(CONFIG_DEDIPROG), yes) FEATURE_CFLAGS += -D'CONFIG_DEDIPROG=1' -FEATURE_LIBS += -lusb PROGRAMMER_OBJS += dediprog.o +NEED_USB := yes endif ifeq ($(CONFIG_SATAMV), yes) @@ -563,23 +565,23 @@ PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(TARGET_OS), NetBSD) # The libpci we want is called libpciutils on NetBSD and needs NetBSD libpci. -LIBS += -lpciutils -lpci +PCILIBS += -lpciutils -lpci # For (i386|x86_64)_iopl(2). -LIBS += -l$(shell uname -p) +PCILIBS += -l$(shell uname -p) else ifeq ($(TARGET_OS), DOS) # FIXME There needs to be a better way to do this CPPFLAGS += -I../libpci/include -LIBS += ../libpci/lib/libpci.a +PCILIBS += ../libpci/lib/libpci.a else -LIBS += -lpci +PCILIBS += -lpci ifeq ($(TARGET_OS), OpenBSD) # For (i386|amd64)_iopl(2). -LIBS += -l$(shell uname -m) +PCILIBS += -l$(shell uname -m) else ifeq ($(TARGET_OS), Darwin) # DirectHW framework can be found in the DirectHW library. -LIBS += -framework IOKit -framework DirectHW +PCILIBS += -framework IOKit -framework DirectHW else endif endif @@ -587,6 +589,12 @@ endif endif +ifeq ($(NEED_USB), yes) +CHECK_LIBUSB0 = yes +FEATURE_CFLAGS += -D'NEED_USB=1' +USBLIBS := $(shell pkg-config --libs libusb 2>/dev/null || printf "%s" "-lusb") +endif + ifeq ($(CONFIG_PRINT_WIKI), yes) FEATURE_CFLAGS += -D'CONFIG_PRINT_WIKI=1' CLI_OBJS += print_wiki.o @@ -600,13 +608,13 @@ LIBFLASHROM_OBJS = $(CHIP_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) OBJS = $(CLI_OBJS) $(LIBFLASHROM_OBJS) -all: pciutils features $(PROGRAM)$(EXEC_SUFFIX) +all: hwlibs features $(PROGRAM)$(EXEC_SUFFIX) ifeq ($(ARCH), x86) @+$(MAKE) -C util/ich_descriptors_tool/ TARGET_OS=$(TARGET_OS) EXEC_SUFFIX=$(EXEC_SUFFIX) endif $(PROGRAM)$(EXEC_SUFFIX): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) $(PCILIBS) $(USBLIBS) libflashrom.a: $(LIBFLASHROM_OBJS) $(AR) rcs $@ $^ @@ -679,8 +687,21 @@ endef export LIBPCI_TEST +define LIBUSB0_TEST +#include <usb.h> +int main(int argc, char **argv) +{ + (void) argc; + (void) argv; + usb_init(); + return 0; +} +endef +export LIBUSB0_TEST + +hwlibs: compiler + @printf "" > .libdeps ifeq ($(CHECK_LIBPCI), yes) -pciutils: compiler @printf "Checking for libpci headers... " @echo "$$LIBPCI_TEST" > .test.c @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ @@ -689,20 +710,32 @@ echo "See README for more information."; echo; \ rm -f .test.c .test.o; exit 1) @printf "Checking if libpci is present and sufficient... " - @printf "" > .libdeps - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) >/dev/null && \ + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(PCILIBS) >/dev/null && \ echo "yes." || ( echo "no."; \ printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) -lz >/dev/null && \ + $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(PCILIBS) -lz >/dev/null && \ ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ echo "Please install libpci (package pciutils) and/or libz."; \ echo "See README for more information."; echo; \ rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -else -pciutils: compiler - @printf "" > .libdeps endif +ifeq ($(CHECK_LIBUSB0), yes) + @printf "Checking for libusb-0.1/libusb-compat headers... " + @echo "$$LIBUSB0_TEST" > .test.c + @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ + echo "found." || ( echo "not found."; echo; \ + echo "Please install libusb-0.1 headers or libusb-compat headers."; \ + echo "See README for more information."; echo; \ + rm -f .test.c .test.o; exit 1) + @printf "Checking if libusb-0.1 is usable... " + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(USBLIBS) >/dev/null && \ + echo "yes." || ( echo "no."; \ + echo "Please install libusb-0.1 or libusb-compat."; \ + echo "See README for more information."; echo; \ + rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) + @rm -f .test.c .test.o .test$(EXEC_SUFFIX) +endif .features: features @@ -816,6 +849,6 @@ libpayload: clean make CC="CC=i386-elf-gcc lpgcc" AR=i386-elf-ar RANLIB=i386-elf-ranlib -.PHONY: all clean distclean compiler pciutils features export tarball dos featuresavailable +.PHONY: all clean distclean compiler hwlibs features export tarball dos featuresavailable -include $(OBJS:.o=.d) -- http://www.hailfinger.org/

2 2

[commit] r1623 - trunk
by repository service 20 Nov '12

20 Nov '12

Author: hailfinger Date: Tue Nov 20 22:06:16 2012 New Revision: 1623 URL: http://flashrom.org/trac/flashrom/changeset/1623 Log: Explicitly detect libusb-0.1 in the Makefile Avoid funny interactions between libpci and libusb detection. Leave libftdi autodetection alone for now. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Nov 5 13:20:29 2012 (r1622) +++ trunk/Makefile Tue Nov 20 22:06:16 2012 (r1623) @@ -480,6 +480,8 @@ FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") PROGRAMMER_OBJS += ft2232_spi.o +# We can't set NEED_USB here because that would transform libftdi auto-enabling +# into a hard requirement for libusb, defeating the purpose of auto-enabling. endif ifeq ($(CONFIG_DUMMY), yes) @@ -531,8 +533,8 @@ ifeq ($(CONFIG_DEDIPROG), yes) FEATURE_CFLAGS += -D'CONFIG_DEDIPROG=1' -FEATURE_LIBS += -lusb PROGRAMMER_OBJS += dediprog.o +NEED_USB := yes endif ifeq ($(CONFIG_SATAMV), yes) @@ -563,23 +565,23 @@ PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(TARGET_OS), NetBSD) # The libpci we want is called libpciutils on NetBSD and needs NetBSD libpci. -LIBS += -lpciutils -lpci +PCILIBS += -lpciutils -lpci # For (i386|x86_64)_iopl(2). -LIBS += -l$(shell uname -p) +PCILIBS += -l$(shell uname -p) else ifeq ($(TARGET_OS), DOS) # FIXME There needs to be a better way to do this CPPFLAGS += -I../libpci/include -LIBS += ../libpci/lib/libpci.a +PCILIBS += ../libpci/lib/libpci.a else -LIBS += -lpci +PCILIBS += -lpci ifeq ($(TARGET_OS), OpenBSD) # For (i386|amd64)_iopl(2). -LIBS += -l$(shell uname -m) +PCILIBS += -l$(shell uname -m) else ifeq ($(TARGET_OS), Darwin) # DirectHW framework can be found in the DirectHW library. -LIBS += -framework IOKit -framework DirectHW +PCILIBS += -framework IOKit -framework DirectHW else endif endif @@ -587,6 +589,12 @@ endif endif +ifeq ($(NEED_USB), yes) +CHECK_LIBUSB0 = yes +FEATURE_CFLAGS += -D'NEED_USB=1' +USBLIBS := $(shell pkg-config --libs libusb 2>/dev/null || printf "%s" "-lusb") +endif + ifeq ($(CONFIG_PRINT_WIKI), yes) FEATURE_CFLAGS += -D'CONFIG_PRINT_WIKI=1' CLI_OBJS += print_wiki.o @@ -600,13 +608,13 @@ LIBFLASHROM_OBJS = $(CHIP_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) OBJS = $(CLI_OBJS) $(LIBFLASHROM_OBJS) -all: pciutils features $(PROGRAM)$(EXEC_SUFFIX) +all: hwlibs features $(PROGRAM)$(EXEC_SUFFIX) ifeq ($(ARCH), x86) @+$(MAKE) -C util/ich_descriptors_tool/ TARGET_OS=$(TARGET_OS) EXEC_SUFFIX=$(EXEC_SUFFIX) endif $(PROGRAM)$(EXEC_SUFFIX): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) $(PCILIBS) $(USBLIBS) libflashrom.a: $(LIBFLASHROM_OBJS) $(AR) rcs $@ $^ @@ -679,8 +687,21 @@ endef export LIBPCI_TEST +define LIBUSB0_TEST +#include <usb.h> +int main(int argc, char **argv) +{ + (void) argc; + (void) argv; + usb_init(); + return 0; +} +endef +export LIBUSB0_TEST + +hwlibs: compiler + @printf "" > .libdeps ifeq ($(CHECK_LIBPCI), yes) -pciutils: compiler @printf "Checking for libpci headers... " @echo "$$LIBPCI_TEST" > .test.c @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ @@ -689,19 +710,31 @@ echo "See README for more information."; echo; \ rm -f .test.c .test.o; exit 1) @printf "Checking if libpci is present and sufficient... " - @printf "" > .libdeps - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) >/dev/null && \ + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(PCILIBS) >/dev/null && \ echo "yes." || ( echo "no."; \ printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) -lz >/dev/null && \ + $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(PCILIBS) -lz >/dev/null && \ ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ echo "Please install libpci (package pciutils) and/or libz."; \ echo "See README for more information."; echo; \ rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -else -pciutils: compiler - @printf "" > .libdeps +endif +ifeq ($(CHECK_LIBUSB0), yes) + @printf "Checking for libusb-0.1/libusb-compat headers... " + @echo "$$LIBUSB0_TEST" > .test.c + @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ + echo "found." || ( echo "not found."; echo; \ + echo "Please install libusb-0.1 headers or libusb-compat headers."; \ + echo "See README for more information."; echo; \ + rm -f .test.c .test.o; exit 1) + @printf "Checking if libusb-0.1 is usable... " + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(USBLIBS) >/dev/null && \ + echo "yes." || ( echo "no."; \ + echo "Please install libusb-0.1 or libusb-compat."; \ + echo "See README for more information."; echo; \ + rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) + @rm -f .test.c .test.o .test$(EXEC_SUFFIX) endif .features: features @@ -816,6 +849,6 @@ libpayload: clean make CC="CC=i386-elf-gcc lpgcc" AR=i386-elf-ar RANLIB=i386-elf-ranlib -.PHONY: all clean distclean compiler pciutils features export tarball dos featuresavailable +.PHONY: all clean distclean compiler hwlibs features export tarball dos featuresavailable -include $(OBJS:.o=.d)

1 0

Need help using Flashrom
by Chea Gittens - IT Specialist 20 Nov '12

20 Nov '12

Hi, I upgraded the BIOS of a Biostar H61MGC motherboard to latest version available on the Biostar website - H61NR709.BSS after I was getting issues with the onboard VGA graphics. I used the flash utility on the motherboard and that reported as successful. However windows 7 would not start it freezes at the logo screen. I cannot get windows 7 boot DVD to start either it also freezes at the logo screen. I was also not able to start Mini Windows XP on a Hiren's Boot CD. I am also unable to start the live CDs disk Parted Magic or SystemRescueCD. Also none of the USB ports work. I was able to start DOS from a FAT32 formatted SATA Hard Drive. I tried to use various DOS Bios Flash tools to flash the bios to a pervious version, however I am getting errors about the bios being write protected. I am currently trying to use flashrom but I would like to get some advice on how to proceed so as to not cause further problems. I tried to do a read and save of the bios and got the follow output: flashrom v0.9.6.1-r1612 on MS-DOS 7 (i686) flashrom was built with libpci 3.1.5, GCC 4.4.4, little endian Command line (7 args): c:/flashrom.exe -r test2.bss -p internal:laptop=this_is_not_a_laptop -o output.txt -V Calibrating delay loop... OS timer resolution is 50000 usecs, 1589M loops per second, delay more than 10% too short (got 88% of expected delay), recalculating... 1661M loops per second, 10 myus = 0 us, 100 myus = 0 us, 1000 myus = 0 us, 10000 myus = 0 us, 200000 myus = 220000 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "" DMI string system-product-name: "" DMI string system-version: "" DMI string baseboard-manufacturer: "" DMI string baseboard-product-name: "" DMI string baseboard-version: "" DMI string chassis-type: "" DMI chassis-type is not specific enough. Found ITE Super I/O, ID 0x8728 on port 0x2e ======================================================================== WARNING! You may be running flashrom on an unsupported laptop. We could not detect this for sure because your vendor has not setup the SMBIOS tables correctly. You can enforce execution by adding '-p internal:laptop=this_is_not_a_laptop' to the command line, but please read the following warning if you are not sure. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Proceeding anyway because user forced us to. Found chipset "Intel H61" with PCI ID 8086:1c5c. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled Root Complex Register Block address = 0xfed1c000 GCS = 0xc04: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00001000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0200 FREG1: BIOS region (0x00200000-0x003fffff) is read-write. 0x5C: 0x01ff0001 FREG2: WARNING: Management Engine region (0x00001000-0x001fffff) is locked. 0x60: 0x00001fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x00001fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00002005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x02040003 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 3 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x09900023 FLILL 0x00000000 --- Details --- Component 1 density: 4 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x03ff0200 FLREG2 0x01ff0001 FLREG3 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00200000 - 0x003fffff Region 2 (ME ) 0x00001000 - 0x001fffff Region 3 (GbE ) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw SPI Read Configuration: prefetching disabled, caching enabled, OK. Super I/O ID 0x8728 is not on the list of flash capable controllers. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Chip status register is 00 Found Eon flash chip "EN25Q32(A/B)" (4096 kB, SPI) at physical address 0xffc00000. Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Numonyx N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0x1c, id2 0x15 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0x1c, id2 0x15 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0x1c, id2 0x15 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 Signature = 0xffffffff (should be 0x50444653) No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3016 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0x1c, id2 0x15 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xf9, id2 0x17, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xf9, id2 0x17, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xf9, id2 0x17, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xf9, id2 0x17, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xf9, id2 0x17, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xae, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Found Eon flash chip "EN25Q32(A/B)" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). === This flash part has status UNTESTED for operations: READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -VE, -Vw), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at fe91f8a0 Restoring MMIO space at fe91f89c Restoring MMIO space at fe91f898 Restoring MMIO space at fe91f896 Restoring MMIO space at fe91f894 Restoring PCI config space for 00:1f:0 reg 0xdc Best Regards, Chea Gittens

1 0

Question for members flashroom
by N.N N.N 20 Nov '12

20 Nov '12

I'd like to raise a concern flashroom members how to make flash motherboards computer SFF HP DC 71000

2 1

GA-M61SME-S2L
by Anton Sizov 19 Nov '12

19 Nov '12

flashrom v0.9.5.2-r1530 on Linux 2.6.32-279.14.1.el6.x86_64 (x86_64), built with libpci 3.1.4, GCC 4.4.6 20110731 (Red Hat 4.4.6-3), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 732M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1049 us, 10000 myus = 10046 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "M61SME-S2L" DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "M61SME-S2L" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8716 on port 0x2e Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Serial flash segment 0xfffe0000-0xffffffff enabled Serial flash segment 0x000e0000-0x000fffff enabled Serial flash segment 0xffee0000-0xffefffff disabled Serial flash segment 0xfff80000-0xfffeffff enabled LPC write to serial flash enabled Serial flash pin 29 Serial flash port 0x0820 The following protocols are supported: LPC, SPI. Probing for AMIC A25L05PT, 64 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L05PU, 64 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L10PT, 128 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L10PU, 128 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L20PT, 256 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L20PU, 256 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L40PT, 512 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L40PU, 512 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L80P, 1024 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L16PT, 2048 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L16PU, 2048 kB: 4 byte RDID not supported on this SPI controller Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L4005" (512 kB, SPI) at physical address 0xfff80000. Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x12, id2 0x12 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x12, id2 0x12 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: 4 byte RDID not supported on this SPI controller Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xcf, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xcf, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xcf, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xcf, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xcf, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Macronix flash chip "MX25L4005" (512 kB, SPI). No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88 -- Best regards, Anton Sizov. phone: +375-25-9771385 e-mail: a.sysoff(a)gmail.com

1 0

[PATCH 3/3] [RFC] Unify usbdev_status and pcidev_status into dev_status.
by Stefan Tauner 17 Nov '12

17 Nov '12

usbdev_status was created for the ft2232 programmer. Its IDs are semantically different because they indicate USB instead of PCI IDs, but apart from that both data structures are equal. This change makes life easier for everything involved in handling and printing the status of devices that is noted in that structure. --- It is still possible to distinguish between PCI and USB devices by using the struct programmer's type field. It still seems a bit hacky, but i think we are better off with it anyway. If we really would want to distinguish between the different types of IDs i'd rater make the IDs a union of different ID types inside struct dev_status. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- atahpt.c | 2 +- drkaiser.c | 2 +- flashrom.c | 40 ++++++++++++++++++++-------------------- ft2232_spi.c | 2 +- gfxnvidia.c | 2 +- nic3com.c | 2 +- nicintel.c | 2 +- nicintel_spi.c | 2 +- nicnatsemi.c | 2 +- nicrealtek.c | 2 +- ogp_spi.c | 2 +- pcidev.c | 2 +- print.c | 19 +++++++++---------- print_wiki.c | 46 +++++++++------------------------------------- programmer.h | 52 +++++++++++++++++++++++++++++----------------------- satamv.c | 2 +- satasii.c | 2 +- 17 files changed, 80 insertions(+), 103 deletions(-) diff --git a/atahpt.c b/atahpt.c index 8ec0f3f..c81b3c4 100644 --- a/atahpt.c +++ b/atahpt.c @@ -33,7 +33,7 @@ #define PCI_VENDOR_ID_HPT 0x1103 -const struct pcidev_status ata_hpt[] = { +const struct dev_status ata_hpt[] = { {0x1103, 0x0004, NT, "Highpoint", "HPT366/368/370/370A/372/372N"}, {0x1103, 0x0005, NT, "Highpoint", "HPT372A/372N"}, {0x1103, 0x0006, NT, "Highpoint", "HPT302/302N"}, diff --git a/drkaiser.c b/drkaiser.c index 8c9f560..9c6ba01 100644 --- a/drkaiser.c +++ b/drkaiser.c @@ -33,7 +33,7 @@ /* Mask to restrict flash accesses to the 128kB memory window. */ #define DRKAISER_MEMMAP_MASK ((1 << 17) - 1) -const struct pcidev_status drkaiser_pcidev[] = { +const struct dev_status drkaiser_pcidev[] = { {0x1803, 0x5057, OK, "Dr. Kaiser", "PC-Waechter (Actel FPGA)"}, {0}, diff --git a/flashrom.c b/flashrom.c index d873276..ae8f70c 100644 --- a/flashrom.c +++ b/flashrom.c @@ -65,7 +65,7 @@ const struct programmer_entry programmer_table[] = { { .name = "internal", .type = OTHER, - .devices.note = NULL, + .devs.note = NULL, .init = internal_init, .map_flash_region = physmap, .unmap_flash_region = physunmap, @@ -78,7 +78,7 @@ const struct programmer_entry programmer_table[] = { .name = "dummy", .type = OTHER, /* FIXME */ - .devices.note = "Dummy device, does nothing and logs all accesses\n", + .devs.note = "Dummy device, does nothing and logs all accesses\n", .init = dummy_init, .map_flash_region = dummy_map, .unmap_flash_region = dummy_unmap, @@ -90,7 +90,7 @@ const struct programmer_entry programmer_table[] = { { .name = "nic3com", .type = PCI, - .devices.pci = nics_3com, + .devs.status = nics_3com, .init = nic3com_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -103,7 +103,7 @@ const struct programmer_entry programmer_table[] = { /* This programmer works for Realtek RTL8139 and SMC 1211. */ .name = "nicrealtek", .type = PCI, - .devices.pci = nics_realtek, + .devs.status = nics_realtek, .init = nicrealtek_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -115,7 +115,7 @@ const struct programmer_entry programmer_table[] = { { .name = "nicnatsemi", .type = PCI, - .devices.pci = nics_natsemi, + .devs.status = nics_natsemi, .init = nicnatsemi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -127,7 +127,7 @@ const struct programmer_entry programmer_table[] = { { .name = "gfxnvidia", .type = PCI, - .devices.pci = gfx_nvidia, + .devs.status = gfx_nvidia, .init = gfxnvidia_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -139,7 +139,7 @@ const struct programmer_entry programmer_table[] = { { .name = "drkaiser", .type = PCI, - .devices.pci = drkaiser_pcidev, + .devs.status = drkaiser_pcidev, .init = drkaiser_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -151,7 +151,7 @@ const struct programmer_entry programmer_table[] = { { .name = "satasii", .type = PCI, - .devices.pci = satas_sii, + .devs.status = satas_sii, .init = satasii_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -163,7 +163,7 @@ const struct programmer_entry programmer_table[] = { { .name = "atahpt", .type = PCI, - .devices.pci = ata_hpt, + .devs.status = ata_hpt, .init = atahpt_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -175,7 +175,7 @@ const struct programmer_entry programmer_table[] = { { .name = "ft2232_spi", .type = USB, - .devices.usb = devs_ft2232spi, + .devs.status = devs_ft2232spi, .init = ft2232_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -188,7 +188,7 @@ const struct programmer_entry programmer_table[] = { .name = "serprog", .type = OTHER, /* FIXME */ - .devices.note = "All programmer devices speaking the serprog protocol\n", + .devs.note = "All programmer devices speaking the serprog protocol\n", .init = serprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -201,7 +201,7 @@ const struct programmer_entry programmer_table[] = { .name = "buspirate_spi", .type = OTHER, /* FIXME */ - .devices.note = "Dangerous Prototypes Bus Pirate\n", + .devs.note = "Dangerous Prototypes Bus Pirate\n", .init = buspirate_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -214,7 +214,7 @@ const struct programmer_entry programmer_table[] = { .name = "dediprog", .type = OTHER, /* FIXME */ - .devices.note = "Dediprog SF100\n", + .devs.note = "Dediprog SF100\n", .init = dediprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -227,7 +227,7 @@ const struct programmer_entry programmer_table[] = { .name = "rayer_spi", .type = OTHER, /* FIXME */ - .devices.note = "RayeR parallel port programmer\n", + .devs.note = "RayeR parallel port programmer\n", .init = rayer_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -240,7 +240,7 @@ const struct programmer_entry programmer_table[] = { .name = "pony_spi", .type = OTHER, /* FIXME */ - .devices.note = "Programmers compatible with SI-Prog, serbang or AJAWe\n", + .devs.note = "Programmers compatible with SI-Prog, serbang or AJAWe\n", .init = pony_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -252,7 +252,7 @@ const struct programmer_entry programmer_table[] = { { .name = "nicintel", .type = PCI, - .devices.pci = nics_intel, + .devs.status = nics_intel, .init = nicintel_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -264,7 +264,7 @@ const struct programmer_entry programmer_table[] = { { .name = "nicintel_spi", .type = PCI, - .devices.pci = nics_intel_spi, + .devs.status = nics_intel_spi, .init = nicintel_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -276,7 +276,7 @@ const struct programmer_entry programmer_table[] = { { .name = "ogp_spi", .type = PCI, - .devices.pci = ogp_spi, + .devs.status = ogp_spi, .init = ogp_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -288,7 +288,7 @@ const struct programmer_entry programmer_table[] = { { .name = "satamv", .type = PCI, - .devices.pci = satas_mv, + .devs.status = satas_mv, .init = satamv_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -300,7 +300,7 @@ const struct programmer_entry programmer_table[] = { { .name = "linux_spi", .type = OTHER, - .devices.note = "Device files /dev/spidev*.*\n", + .devs.note = "Device files /dev/spidev*.*\n", .init = linux_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, diff --git a/ft2232_spi.c b/ft2232_spi.c index dc17d00..aaeca67 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -57,7 +57,7 @@ #define OLIMEX_ARM_OCD_H_PID 0x002B #define OLIMEX_ARM_TINY_H_PID 0x002A -const struct usbdev_status devs_ft2232spi[] = { +const struct dev_status devs_ft2232spi[] = { {FTDI_VID, FTDI_FT2232H_PID, OK, "FTDI", "FT2232H"}, {FTDI_VID, FTDI_FT4232H_PID, OK, "FTDI", "FT4232H"}, {FTDI_VID, FTDI_FT232H_PID, OK, "FTDI", "FT232H"}, diff --git a/gfxnvidia.c b/gfxnvidia.c index 7bdbda8..4c334eb 100644 --- a/gfxnvidia.c +++ b/gfxnvidia.c @@ -34,7 +34,7 @@ uint8_t *nvidia_bar; -const struct pcidev_status gfx_nvidia[] = { +const struct dev_status gfx_nvidia[] = { {0x10de, 0x0010, NT, "NVIDIA", "Mutara V08 [NV2]" }, {0x10de, 0x0018, NT, "NVIDIA", "RIVA 128" }, {0x10de, 0x0020, NT, "NVIDIA", "RIVA TNT" }, diff --git a/nic3com.c b/nic3com.c index c7fc800..4e623e0 100644 --- a/nic3com.c +++ b/nic3com.c @@ -36,7 +36,7 @@ static uint32_t internal_conf; static uint16_t id; -const struct pcidev_status nics_3com[] = { +const struct dev_status nics_3com[] = { /* 3C90xB */ {0x10b7, 0x9055, OK, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-TX"}, {0x10b7, 0x9001, NT, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-T4" }, diff --git a/nicintel.c b/nicintel.c index 4399377..8c8ce0d 100644 --- a/nicintel.c +++ b/nicintel.c @@ -27,7 +27,7 @@ uint8_t *nicintel_bar; uint8_t *nicintel_control_bar; -const struct pcidev_status nics_intel[] = { +const struct dev_status nics_intel[] = { {PCI_VENDOR_ID_INTEL, 0x1209, NT, "Intel", "8255xER/82551IT Fast Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x1229, OK, "Intel", "82557/8/9/0/1 Ethernet Pro 100"}, diff --git a/nicintel_spi.c b/nicintel_spi.c index 24d5732..160e050 100644 --- a/nicintel_spi.c +++ b/nicintel_spi.c @@ -67,7 +67,7 @@ uint8_t *nicintel_spibar; -const struct pcidev_status nics_intel_spi[] = { +const struct dev_status nics_intel_spi[] = { {PCI_VENDOR_ID_INTEL, 0x105e, OK, "Intel", "82571EB Gigabit Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x1076, OK, "Intel", "82541GI Gigabit Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x107c, OK, "Intel", "82541PI Gigabit Ethernet Controller"}, diff --git a/nicnatsemi.c b/nicnatsemi.c index fcfc613..e7ba5af 100644 --- a/nicnatsemi.c +++ b/nicnatsemi.c @@ -30,7 +30,7 @@ #define BOOT_ROM_ADDR 0x50 #define BOOT_ROM_DATA 0x54 -const struct pcidev_status nics_natsemi[] = { +const struct dev_status nics_natsemi[] = { {0x100b, 0x0020, NT, "National Semiconductor", "DP83815/DP83816"}, {0x100b, 0x0022, NT, "National Semiconductor", "DP83820"}, diff --git a/nicrealtek.c b/nicrealtek.c index 92f48a8..2fee7c4 100644 --- a/nicrealtek.c +++ b/nicrealtek.c @@ -30,7 +30,7 @@ static int bios_rom_addr, bios_rom_data; -const struct pcidev_status nics_realtek[] = { +const struct dev_status nics_realtek[] = { {0x10ec, 0x8139, OK, "Realtek", "RTL8139/8139C/8139C+"}, {0x10ec, 0x8169, NT, "Realtek", "RTL8169"}, {0x1113, 0x1211, OK, "SMC", "1211TX"}, /* RTL8139 clone */ diff --git a/ogp_spi.c b/ogp_spi.c index 7aee72b..d2fec8a 100644 --- a/ogp_spi.c +++ b/ogp_spi.c @@ -47,7 +47,7 @@ static uint32_t ogp_reg_siso; static uint32_t ogp_reg__ce; static uint32_t ogp_reg_sck; -const struct pcidev_status ogp_spi[] = { +const struct dev_status ogp_spi[] = { {PCI_VENDOR_ID_OGP, 0x0000, OK, "Open Graphics Project", "Development Board OGD1"}, {0}, diff --git a/pcidev.c b/pcidev.c index bfc8a5d..e1d3875 100644 --- a/pcidev.c +++ b/pcidev.c @@ -154,7 +154,7 @@ uintptr_t pcidev_readbar(struct pci_dev *dev, int bar) return (uintptr_t)addr; } -uintptr_t pcidev_init(int bar, const struct pcidev_status *devs) +uintptr_t pcidev_init(int bar, const struct dev_status *devs) { struct pci_dev *dev; struct pci_filter filter; diff --git a/print.c b/print.c index 4b23ca0..69c9688 100644 --- a/print.c +++ b/print.c @@ -433,11 +433,12 @@ static void print_supported_boards_helper(const struct board_info *boards, } #endif -void print_supported_usbdevs(const struct usbdev_status *devs) +void print_supported_devs(const struct programmer_entry prog, const char *const type) { int i; - msg_pinfo("USB devices:\n"); + const struct dev_status *const devs = prog.devs.status; + msg_ginfo("\nSupported %s devices for the %s programmer:\n", type, prog.name); for (i = 0; devs[i].vendor_name != NULL; i++) { msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, devs[i].device_id, (devs[i].status == NT) ? " (untested)" : ""); @@ -477,20 +478,18 @@ int print_supported(void) const struct programmer_entry prog = programmer_table[i]; switch (prog.type) { case USB: - msg_ginfo("\nSupported USB devices for the %s programmer:\n", prog.name); - print_supported_usbdevs(prog.devices.usb); + print_supported_devs(prog, "USB"); break; #if NEED_PCI == 1 case PCI: - msg_ginfo("\nSupported PCI devices for the %s programmer:\n", prog.name); - print_supported_pcidevs(prog.devices.pci); + print_supported_devs(prog, "PCI"); break; #endif case OTHER: - if (prog.devices.note == NULL) - break; - msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); - msg_ginfo("%s", prog.devices.note); + if (prog.devs.note != NULL) { + msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); + msg_ginfo("%s", prog.devs.note); + } break; default: msg_gerr("\n%s: %s: Uninitialized programmer type! Please report a bug at " diff --git a/print_wiki.c b/print_wiki.c index d936682..55a88fa 100644 --- a/print_wiki.c +++ b/print_wiki.c @@ -301,49 +301,21 @@ static void print_supported_chips_wiki(int cols) /* Following functions are not needed when no PCI/USB programmers are compiled in, * but since print_wiki code has no size constraints we include it unconditionally. */ -static int count_supported_pcidevs_wiki(const struct pcidev_status *devs) +static int count_supported_devs_wiki(const struct dev_status *devs) { unsigned int count = 0; unsigned int i = 0; for (i = 0; devs[i].vendor_name != NULL; i++) - count++; + count++; return count; } -static void print_supported_pcidevs_wiki_helper(const struct programmer_entry prog) +static void print_supported_devs_wiki_helper(const struct programmer_entry prog) { int i = 0; static int c = 0; - const struct pcidev_status *devs = prog.devices.pci; - const unsigned int count = count_supported_pcidevs_wiki(devs); - - /* Alternate colors if the vendor changes. */ - c = !c; - - for (i = 0; devs[i].vendor_name != NULL; i++) { - printf("|- bgcolor=\"#%s\"\n", (c) ? "eeeeee" : "dddddd"); - if (i == 0) - printf("| rowspan=\"%u\" | %s |", count, prog.name); - printf("| %s || %s || %04x:%04x || {{%s}}\n", devs[i].vendor_name, devs[i].device_name, - devs[i].vendor_id, devs[i].device_id, (devs[i].status == NT) ? "?3" : "OK"); - } -} - -static int count_supported_usbdevs_wiki(const struct usbdev_status *devs) -{ - unsigned int count = 0; - unsigned int i = 0; - for (i = 0; devs[i].vendor_name != NULL; i++) - count++; - return count; -} - -static void print_supported_usbdevs_wiki_helper(const struct programmer_entry prog) -{ - int i = 0; - static int c = 0; - const struct usbdev_status *devs = prog.devices.usb; - const unsigned int count = count_supported_usbdevs_wiki(devs); + const struct dev_status *devs = prog.devs.status; + const unsigned int count = count_supported_devs_wiki(devs); /* Alternate colors if the vendor changes. */ c = !c; @@ -367,10 +339,10 @@ static void print_supported_devs_wiki() const struct programmer_entry prog = programmer_table[i]; switch (prog.type) { case USB: - usb_count += count_supported_usbdevs_wiki(prog.devices.usb); + usb_count += count_supported_devs_wiki(prog.devs.status); break; case PCI: - pci_count += count_supported_pcidevs_wiki(prog.devices.pci); + pci_count += count_supported_devs_wiki(prog.devs.status); break; case OTHER: default: @@ -385,7 +357,7 @@ static void print_supported_devs_wiki() for (i = 0; i < PROGRAMMER_INVALID; i++) { const struct programmer_entry prog = programmer_table[i]; if (prog.type == PCI) { - print_supported_pcidevs_wiki_helper(prog); + print_supported_devs_wiki_helper(prog); } } printf("\n|}\n\n|}\n"); @@ -397,7 +369,7 @@ static void print_supported_devs_wiki() for (i = 0; i < PROGRAMMER_INVALID; i++) { const struct programmer_entry prog = programmer_table[i]; if (prog.type == USB) { - print_supported_usbdevs_wiki_helper(prog); + print_supported_devs_wiki_helper(prog); } } printf("\n|}\n\n|}\n"); diff --git a/programmer.h b/programmer.h index 21fa707..90033a9 100644 --- a/programmer.h +++ b/programmer.h @@ -96,15 +96,22 @@ enum programmer_type { OTHER, }; +struct dev_status { + uint16_t vendor_id; + uint16_t device_id; + const enum test_state status; + const char *vendor_name; + const char *device_name; +}; + struct programmer_entry { const char *vendor; const char *name; const enum programmer_type type; union { - const struct pcidev_status *const pci; - const struct usbdev_status *const usb; + const struct dev_status *const status; const char *const note; - } devices; + } devs; int (*init) (void); @@ -234,7 +241,7 @@ extern uint32_t io_base_addr; extern struct pci_access *pacc; extern struct pci_dev *pcidev_dev; uintptr_t pcidev_readbar(struct pci_dev *dev, int bar); -uintptr_t pcidev_init(int bar, const struct pcidev_status *devs); +uintptr_t pcidev_init(int bar, const struct dev_status *devs); /* rpci_write_* are reversible writes. The original PCI config space register * contents will be restored on shutdown. */ @@ -243,12 +250,6 @@ int rpci_write_word(struct pci_dev *dev, int reg, uint16_t data); int rpci_write_long(struct pci_dev *dev, int reg, uint32_t data); #endif -/* print.c */ -#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_NICINTEL+CONFIG_NICINTEL_SPI+CONFIG_OGP_SPI+CONFIG_SATAMV >= 1 -/* Not needed for CONFIG_INTERNAL, but for all other PCI-based programmers. */ -void print_supported_pcidevs(const struct pcidev_status *devs); -#endif - struct usbdev_status { uint16_t vendor_id; uint16_t device_id; @@ -264,6 +265,12 @@ struct pcidev_status { const char *device_name; }; +/* print.c */ +#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_NICINTEL+CONFIG_NICINTEL_SPI+CONFIG_OGP_SPI+CONFIG_SATAMV >= 1 +/* Not needed for CONFIG_INTERNAL, but for all other PCI-based programmers. */ +void print_supported_pcidevs(const struct pcidev_status *devs); +#endif + #if CONFIG_INTERNAL == 1 /* board_enable.c */ int board_parse_parameter(const char *boardstring, const char **vendor, const char **model); @@ -377,74 +384,73 @@ void dummy_unmap(void *virt_addr, size_t len); /* nic3com.c */ #if CONFIG_NIC3COM == 1 int nic3com_init(void); -extern const struct pcidev_status nics_3com[]; +extern const struct dev_status nics_3com[]; #endif /* gfxnvidia.c */ #if CONFIG_GFXNVIDIA == 1 int gfxnvidia_init(void); -extern const struct pcidev_status gfx_nvidia[]; +extern const struct dev_status gfx_nvidia[]; #endif /* drkaiser.c */ #if CONFIG_DRKAISER == 1 int drkaiser_init(void); -extern const struct pcidev_status drkaiser_pcidev[]; +extern const struct dev_status drkaiser_pcidev[]; #endif /* nicrealtek.c */ #if CONFIG_NICREALTEK == 1 int nicrealtek_init(void); -extern const struct pcidev_status nics_realtek[]; +extern const struct dev_status nics_realtek[]; #endif /* nicnatsemi.c */ #if CONFIG_NICNATSEMI == 1 int nicnatsemi_init(void); -extern const struct pcidev_status nics_natsemi[]; +extern const struct dev_status nics_natsemi[]; #endif /* nicintel.c */ #if CONFIG_NICINTEL == 1 int nicintel_init(void); -extern const struct pcidev_status nics_intel[]; +extern const struct dev_status nics_intel[]; #endif /* nicintel_spi.c */ #if CONFIG_NICINTEL_SPI == 1 int nicintel_spi_init(void); -extern const struct pcidev_status nics_intel_spi[]; +extern const struct dev_status nics_intel_spi[]; #endif /* ogp_spi.c */ #if CONFIG_OGP_SPI == 1 int ogp_spi_init(void); -extern const struct pcidev_status ogp_spi[]; +extern const struct dev_status ogp_spi[]; #endif /* satamv.c */ #if CONFIG_SATAMV == 1 int satamv_init(void); -extern const struct pcidev_status satas_mv[]; +extern const struct dev_status satas_mv[]; #endif /* satasii.c */ #if CONFIG_SATASII == 1 int satasii_init(void); -extern const struct pcidev_status satas_sii[]; +extern const struct dev_status satas_sii[]; #endif /* atahpt.c */ #if CONFIG_ATAHPT == 1 int atahpt_init(void); -extern const struct pcidev_status ata_hpt[]; +extern const struct dev_status ata_hpt[]; #endif /* ft2232_spi.c */ #if CONFIG_FT2232_SPI == 1 int ft2232_spi_init(void); -extern const struct usbdev_status devs_ft2232spi[]; -void print_supported_usbdevs(const struct usbdev_status *devs); +extern const struct dev_status devs_ft2232spi[]; #endif /* rayer_spi.c */ diff --git a/satamv.c b/satamv.c index 27ad699..0fc9a25 100644 --- a/satamv.c +++ b/satamv.c @@ -29,7 +29,7 @@ uint8_t *mv_bar; uint16_t mv_iobar; -const struct pcidev_status satas_mv[] = { +const struct dev_status satas_mv[] = { /* 88SX6041 and 88SX6042 are the same according to the datasheet. */ {0x11ab, 0x7042, OK, "Marvell", "88SX7042 PCI-e 4-port SATA-II"}, diff --git a/satasii.c b/satasii.c index f991686..96b73a1 100644 --- a/satasii.c +++ b/satasii.c @@ -30,7 +30,7 @@ static uint8_t *sii_bar; static uint16_t id; -const struct pcidev_status satas_sii[] = { +const struct dev_status satas_sii[] = { {0x1095, 0x0680, OK, "Silicon Image", "PCI0680 Ultra ATA-133 Host Ctrl"}, {0x1095, 0x3112, OK, "Silicon Image", "SiI 3112 [SATALink/SATARaid] SATA Ctrl"}, {0x1095, 0x3114, OK, "Silicon Image", "SiI 3114 [SATALink/SATARaid] SATA Ctrl"}, -- Kind regards, Stefan Tauner

1 0

[PATCH 2/3] print_wiki.c: add a programmer column to the PCI and USB devices lists
by Stefan Tauner 17 Nov '12

17 Nov '12

Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- print_wiki.c | 29 +++++++++++++++++++---------- 1 file changed, 19 insertions(+), 10 deletions(-) diff --git a/print_wiki.c b/print_wiki.c index 17e2e85..d936682 100644 --- a/print_wiki.c +++ b/print_wiki.c @@ -77,6 +77,7 @@ static const char chip_th[] = "\ | align=\"center\" | Min \n| align=\"center\" | Max\n\n"; static const char programmer_th[] = "\ +! align=\"left\" | Programmer\n\ ! align=\"left\" | Vendor\n\ ! align=\"left\" | Device\n\ ! align=\"center\" | IDs\n\ @@ -309,18 +310,22 @@ static int count_supported_pcidevs_wiki(const struct pcidev_status *devs) return count; } -static void print_supported_pcidevs_wiki_helper(const struct pcidev_status *devs) +static void print_supported_pcidevs_wiki_helper(const struct programmer_entry prog) { int i = 0; static int c = 0; + const struct pcidev_status *devs = prog.devices.pci; + const unsigned int count = count_supported_pcidevs_wiki(devs); /* Alternate colors if the vendor changes. */ c = !c; for (i = 0; devs[i].vendor_name != NULL; i++) { - printf("|- bgcolor=\"#%s\"\n| %s || %s || %04x:%04x || {{%s}}\n", (c) ? "eeeeee" : "dddddd", - devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, devs[i].device_id, - (devs[i].status == NT) ? "?3" : "OK"); + printf("|- bgcolor=\"#%s\"\n", (c) ? "eeeeee" : "dddddd"); + if (i == 0) + printf("| rowspan=\"%u\" | %s |", count, prog.name); + printf("| %s || %s || %04x:%04x || {{%s}}\n", devs[i].vendor_name, devs[i].device_name, + devs[i].vendor_id, devs[i].device_id, (devs[i].status == NT) ? "?3" : "OK"); } } @@ -333,18 +338,22 @@ static int count_supported_usbdevs_wiki(const struct usbdev_status *devs) return count; } -static void print_supported_usbdevs_wiki_helper(const struct usbdev_status *devs) +static void print_supported_usbdevs_wiki_helper(const struct programmer_entry prog) { int i = 0; static int c = 0; + const struct usbdev_status *devs = prog.devices.usb; + const unsigned int count = count_supported_usbdevs_wiki(devs); /* Alternate colors if the vendor changes. */ c = !c; for (i = 0; devs[i].vendor_name != NULL; i++) { - printf("|- bgcolor=\"#%s\"\n| %s || %s || %04x:%04x || {{%s}}\n", (c) ? "eeeeee" : "dddddd", - devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, devs[i].device_id, - (devs[i].status == NT) ? "?3" : "OK"); + printf("|- bgcolor=\"#%s\"\n", (c) ? "eeeeee" : "dddddd"); + if (i == 0) + printf("| rowspan=\"%u\" | %s |", count, prog.name); + printf("| %s || %s || %04x:%04x || {{%s}}\n", devs[i].vendor_name, devs[i].device_name, + devs[i].vendor_id, devs[i].device_id, devs[i].status == NT ? "?3" : "OK"); } } @@ -376,7 +385,7 @@ static void print_supported_devs_wiki() for (i = 0; i < PROGRAMMER_INVALID; i++) { const struct programmer_entry prog = programmer_table[i]; if (prog.type == PCI) { - print_supported_pcidevs_wiki_helper(prog.devices.pci); + print_supported_pcidevs_wiki_helper(prog); } } printf("\n|}\n\n|}\n"); @@ -388,7 +397,7 @@ static void print_supported_devs_wiki() for (i = 0; i < PROGRAMMER_INVALID; i++) { const struct programmer_entry prog = programmer_table[i]; if (prog.type == USB) { - print_supported_usbdevs_wiki_helper(prog.devices.usb); + print_supported_usbdevs_wiki_helper(prog); } } printf("\n|}\n\n|}\n"); -- Kind regards, Stefan Tauner

1 0

[PATCH 1/3] Refactor PCI and USB device status printing.
by Stefan Tauner 17 Nov '12

17 Nov '12

To be able to get rid of lots of #ifdefs and centralize programmer-specific data more... - introduce two new fields to struct programmer_entry, namely enum type (OTHER, USB, PCI) and union devices (pcidev_status, usbdev_status or char *note). - use those fields to generate device listings in print.c and print_wiki.c. Bonus: add printing of USB devices to print_wiki.c and count supported PCI and USB devices. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- flashrom.c | 48 ++++++++++++++++++- ft2232_spi.c | 13 ------ pcidev.c | 13 ------ print.c | 148 +++++++++++++++++++--------------------------------------- print_wiki.c | 141 ++++++++++++++++++++++++++++++++++--------------------- programmer.h | 41 ++++++++++------ 6 files changed, 211 insertions(+), 193 deletions(-) diff --git a/flashrom.c b/flashrom.c index 2299b06..d873276 100644 --- a/flashrom.c +++ b/flashrom.c @@ -64,6 +64,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_INTERNAL == 1 { .name = "internal", + .type = OTHER, + .devices.note = NULL, .init = internal_init, .map_flash_region = physmap, .unmap_flash_region = physunmap, @@ -74,6 +76,9 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_DUMMY == 1 { .name = "dummy", + .type = OTHER, + /* FIXME */ + .devices.note = "Dummy device, does nothing and logs all accesses\n", .init = dummy_init, .map_flash_region = dummy_map, .unmap_flash_region = dummy_unmap, @@ -84,6 +89,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_NIC3COM == 1 { .name = "nic3com", + .type = PCI, + .devices.pci = nics_3com, .init = nic3com_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -95,6 +102,8 @@ const struct programmer_entry programmer_table[] = { { /* This programmer works for Realtek RTL8139 and SMC 1211. */ .name = "nicrealtek", + .type = PCI, + .devices.pci = nics_realtek, .init = nicrealtek_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -105,6 +114,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_NICNATSEMI == 1 { .name = "nicnatsemi", + .type = PCI, + .devices.pci = nics_natsemi, .init = nicnatsemi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -115,6 +126,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_GFXNVIDIA == 1 { .name = "gfxnvidia", + .type = PCI, + .devices.pci = gfx_nvidia, .init = gfxnvidia_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -125,6 +138,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_DRKAISER == 1 { .name = "drkaiser", + .type = PCI, + .devices.pci = drkaiser_pcidev, .init = drkaiser_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -135,6 +150,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_SATASII == 1 { .name = "satasii", + .type = PCI, + .devices.pci = satas_sii, .init = satasii_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -145,6 +162,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_ATAHPT == 1 { .name = "atahpt", + .type = PCI, + .devices.pci = ata_hpt, .init = atahpt_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -155,6 +174,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_FT2232_SPI == 1 { .name = "ft2232_spi", + .type = USB, + .devices.usb = devs_ft2232spi, .init = ft2232_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -165,6 +186,9 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_SERPROG == 1 { .name = "serprog", + .type = OTHER, + /* FIXME */ + .devices.note = "All programmer devices speaking the serprog protocol\n", .init = serprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -175,6 +199,9 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_BUSPIRATE_SPI == 1 { .name = "buspirate_spi", + .type = OTHER, + /* FIXME */ + .devices.note = "Dangerous Prototypes Bus Pirate\n", .init = buspirate_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -185,6 +212,9 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_DEDIPROG == 1 { .name = "dediprog", + .type = OTHER, + /* FIXME */ + .devices.note = "Dediprog SF100\n", .init = dediprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -195,6 +225,9 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_RAYER_SPI == 1 { .name = "rayer_spi", + .type = OTHER, + /* FIXME */ + .devices.note = "RayeR parallel port programmer\n", .init = rayer_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -205,16 +238,21 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_PONY_SPI == 1 { .name = "pony_spi", + .type = OTHER, + /* FIXME */ + .devices.note = "Programmers compatible with SI-Prog, serbang or AJAWe\n", .init = pony_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, .delay = internal_delay, -}, + }, #endif #if CONFIG_NICINTEL == 1 { .name = "nicintel", + .type = PCI, + .devices.pci = nics_intel, .init = nicintel_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -225,6 +263,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_NICINTEL_SPI == 1 { .name = "nicintel_spi", + .type = PCI, + .devices.pci = nics_intel_spi, .init = nicintel_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -235,6 +275,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_OGP_SPI == 1 { .name = "ogp_spi", + .type = PCI, + .devices.pci = ogp_spi, .init = ogp_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -245,6 +287,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_SATAMV == 1 { .name = "satamv", + .type = PCI, + .devices.pci = satas_mv, .init = satamv_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -255,6 +299,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_LINUX_SPI == 1 { .name = "linux_spi", + .type = OTHER, + .devices.note = "Device files /dev/spidev*.*\n", .init = linux_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, diff --git a/ft2232_spi.c b/ft2232_spi.c index c09405e..dc17d00 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -482,17 +482,4 @@ static int ft2232_spi_send_command(struct flashctx *flash, return failed ? -1 : 0; } -void print_supported_usbdevs(const struct usbdev_status *devs) -{ - int i; - - msg_pinfo("USB devices:\n"); - for (i = 0; devs[i].vendor_name != NULL; i++) { - msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, - devs[i].device_name, devs[i].vendor_id, - devs[i].device_id, - (devs[i].status == NT) ? " (untested)" : ""); - } -} - #endif diff --git a/pcidev.c b/pcidev.c index c1b6d6a..bfc8a5d 100644 --- a/pcidev.c +++ b/pcidev.c @@ -224,19 +224,6 @@ uintptr_t pcidev_init(int bar, const struct pcidev_status *devs) return curaddr; } -void print_supported_pcidevs(const struct pcidev_status *devs) -{ - int i; - - msg_pinfo("PCI devices:\n"); - for (i = 0; devs[i].vendor_name != NULL; i++) { - msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, - devs[i].device_name, devs[i].vendor_id, - devs[i].device_id, - (devs[i].status == NT) ? " (untested)" : ""); - } -} - enum pci_write_type { pci_write_type_byte, pci_write_type_word, diff --git a/print.c b/print.c index d7bdbfe..4b23ca0 100644 --- a/print.c +++ b/print.c @@ -433,8 +433,32 @@ static void print_supported_boards_helper(const struct board_info *boards, } #endif +void print_supported_usbdevs(const struct usbdev_status *devs) +{ + int i; + + msg_pinfo("USB devices:\n"); + for (i = 0; devs[i].vendor_name != NULL; i++) { + msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, + devs[i].device_id, (devs[i].status == NT) ? " (untested)" : ""); + } +} + +#if NEED_PCI == 1 +void print_supported_pcidevs(const struct pcidev_status *devs) +{ + int i; + + for (i = 0; devs[i].vendor_name != NULL; i++) { + msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, + devs[i].device_id, (devs[i].status == NT) ? " (untested)" : ""); + } +} +#endif + int print_supported(void) { + unsigned int i; if (print_supported_chips()) return 1; @@ -449,107 +473,31 @@ int print_supported(void) msg_ginfo("\n"); print_supported_boards_helper(laptops_known, "laptops"); #endif -#if CONFIG_DUMMY == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_DUMMY].name); - /* FIXME */ - msg_ginfo("Dummy device, does nothing and logs all accesses\n"); -#endif -#if CONFIG_NIC3COM == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_NIC3COM].name); - print_supported_pcidevs(nics_3com); -#endif -#if CONFIG_NICREALTEK == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_NICREALTEK].name); - print_supported_pcidevs(nics_realtek); -#endif -#if CONFIG_NICNATSEMI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_NICNATSEMI].name); - print_supported_pcidevs(nics_natsemi); -#endif -#if CONFIG_GFXNVIDIA == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_GFXNVIDIA].name); - print_supported_pcidevs(gfx_nvidia); -#endif -#if CONFIG_DRKAISER == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_DRKAISER].name); - print_supported_pcidevs(drkaiser_pcidev); -#endif -#if CONFIG_SATASII == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_SATASII].name); - print_supported_pcidevs(satas_sii); -#endif -#if CONFIG_ATAHPT == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_ATAHPT].name); - print_supported_pcidevs(ata_hpt); -#endif -#if CONFIG_FT2232_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_FT2232_SPI].name); - print_supported_usbdevs(devs_ft2232spi); -#endif -#if CONFIG_SERPROG == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_SERPROG].name); - /* FIXME */ - msg_ginfo("All programmer devices speaking the serprog protocol\n"); -#endif -#if CONFIG_BUSPIRATE_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_BUSPIRATE_SPI].name); - /* FIXME */ - msg_ginfo("Dangerous Prototypes Bus Pirate\n"); -#endif -#if CONFIG_DEDIPROG == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_DEDIPROG].name); - /* FIXME */ - msg_ginfo("Dediprog SF100\n"); -#endif -#if CONFIG_RAYER_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_RAYER_SPI].name); - /* FIXME */ - msg_ginfo("RayeR parallel port programmer\n"); -#endif -#if CONFIG_PONY_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_PONY_SPI].name); - /* FIXME */ - msg_ginfo("SI-Prog, serbang and AJAWe serial port programmers\n"); -#endif -#if CONFIG_NICINTEL == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_NICINTEL].name); - print_supported_pcidevs(nics_intel); -#endif -#if CONFIG_NICINTEL_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_NICINTEL_SPI].name); - print_supported_pcidevs(nics_intel_spi); -#endif -#if CONFIG_OGP_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_OGP_SPI].name); - print_supported_pcidevs(ogp_spi); -#endif -#if CONFIG_SATAMV == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_SATAMV].name); - print_supported_pcidevs(satas_mv); -#endif -#if CONFIG_LINUX_SPI == 1 - msg_ginfo("\nSupported devices for the %s programmer:\n", - programmer_table[PROGRAMMER_LINUX_SPI].name); - msg_ginfo("Device files /dev/spidev*.*\n"); + for (i = 0; i < PROGRAMMER_INVALID; i++) { + const struct programmer_entry prog = programmer_table[i]; + switch (prog.type) { + case USB: + msg_ginfo("\nSupported USB devices for the %s programmer:\n", prog.name); + print_supported_usbdevs(prog.devices.usb); + break; +#if NEED_PCI == 1 + case PCI: + msg_ginfo("\nSupported PCI devices for the %s programmer:\n", prog.name); + print_supported_pcidevs(prog.devices.pci); + break; #endif + case OTHER: + if (prog.devices.note == NULL) + break; + msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); + msg_ginfo("%s", prog.devices.note); + break; + default: + msg_gerr("\n%s: %s: Uninitialized programmer type! Please report a bug at " + "flashrom(a)flashrom.org\n", __func__, prog.name); + break; + } + } return 0; } diff --git a/print_wiki.c b/print_wiki.c index 617053c..17e2e85 100644 --- a/print_wiki.c +++ b/print_wiki.c @@ -79,13 +79,9 @@ static const char chip_th[] = "\ static const char programmer_th[] = "\ ! align=\"left\" | Vendor\n\ ! align=\"left\" | Device\n\ -! align=\"center\" | PCI IDs\n\ +! align=\"center\" | IDs\n\ ! align=\"center\" | Status\n\n"; -static const char programmer_intro[] = "\ -\n== Supported programmers ==\n\n\ -This is a list of supported PCI devices flashrom can use as programmer:\n\n{"; - #if CONFIG_INTERNAL == 1 static const char laptop_intro[] = "\n== Supported laptops/notebooks ==\n\n\ In general, flashing laptops is more difficult because laptops\n\n\ @@ -139,7 +135,7 @@ static void print_supported_chipsets_wiki(int cols) printf("\n\n|}\n"); } -static void wiki_helper(const char *devicetype, int cols, const struct board_info boards[]) +static void print_supported_boards_wiki_helper(const char *devicetype, int cols, const struct board_info boards[]) { int i, k; unsigned int boardcount, lines_per_col; @@ -222,10 +218,10 @@ static void wiki_helper(const char *devicetype, int cols, const struct board_inf static void print_supported_boards_wiki(void) { printf("%s", board_intro); - wiki_helper("boards", 2, boards_known); + print_supported_boards_wiki_helper("boards", 2, boards_known); printf("%s", laptop_intro); - wiki_helper("laptops", 1, laptops_known); + print_supported_boards_wiki_helper("laptops", 1, laptops_known); } #endif @@ -302,9 +298,18 @@ static void print_supported_chips_wiki(int cols) printf("|}\n\n"); } -/* Not needed for CONFIG_INTERNAL, but for all other PCI-based programmers. */ -#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_NICINTEL+CONFIG_NICINTEL_SPI+CONFIG_OGP_SPI+CONFIG_SATAMV >= 1 -static void print_supported_pcidevs_wiki(const struct pcidev_status *devs) +/* Following functions are not needed when no PCI/USB programmers are compiled in, + * but since print_wiki code has no size constraints we include it unconditionally. */ +static int count_supported_pcidevs_wiki(const struct pcidev_status *devs) +{ + unsigned int count = 0; + unsigned int i = 0; + for (i = 0; devs[i].vendor_name != NULL; i++) + count++; + return count; +} + +static void print_supported_pcidevs_wiki_helper(const struct pcidev_status *devs) { int i = 0; static int c = 0; @@ -313,14 +318,81 @@ static void print_supported_pcidevs_wiki(const struct pcidev_status *devs) c = !c; for (i = 0; devs[i].vendor_name != NULL; i++) { - printf("|- bgcolor=\"#%s\"\n| %s || %s || " - "%04x:%04x || {{%s}}\n", (c) ? "eeeeee" : "dddddd", - devs[i].vendor_name, devs[i].device_name, - devs[i].vendor_id, devs[i].device_id, + printf("|- bgcolor=\"#%s\"\n| %s || %s || %04x:%04x || {{%s}}\n", (c) ? "eeeeee" : "dddddd", + devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, devs[i].device_id, (devs[i].status == NT) ? "?3" : "OK"); } } -#endif + +static int count_supported_usbdevs_wiki(const struct usbdev_status *devs) +{ + unsigned int count = 0; + unsigned int i = 0; + for (i = 0; devs[i].vendor_name != NULL; i++) + count++; + return count; +} + +static void print_supported_usbdevs_wiki_helper(const struct usbdev_status *devs) +{ + int i = 0; + static int c = 0; + + /* Alternate colors if the vendor changes. */ + c = !c; + + for (i = 0; devs[i].vendor_name != NULL; i++) { + printf("|- bgcolor=\"#%s\"\n| %s || %s || %04x:%04x || {{%s}}\n", (c) ? "eeeeee" : "dddddd", + devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, devs[i].device_id, + (devs[i].status == NT) ? "?3" : "OK"); + } +} + +static void print_supported_devs_wiki() +{ + unsigned int pci_count = 0; + unsigned int usb_count = 0; + unsigned int i; + + for (i = 0; i < PROGRAMMER_INVALID; i++) { + const struct programmer_entry prog = programmer_table[i]; + switch (prog.type) { + case USB: + usb_count += count_supported_usbdevs_wiki(prog.devices.usb); + break; + case PCI: + pci_count += count_supported_pcidevs_wiki(prog.devices.pci); + break; + case OTHER: + default: + break; + } + } + + printf("\n== PCI Devices ==\n\n" + "Total amount of supported PCI devices flashrom can use as a programmer: '''%d'''\n\n" + "{%s%s", pci_count, th_start, programmer_th); + + for (i = 0; i < PROGRAMMER_INVALID; i++) { + const struct programmer_entry prog = programmer_table[i]; + if (prog.type == PCI) { + print_supported_pcidevs_wiki_helper(prog.devices.pci); + } + } + printf("\n|}\n\n|}\n"); + + printf("\n== USB Devices ==\n\n" + "Total amount of supported USB devices flashrom can use as a programmer: '''%d'''\n\n" + "{%s%s", usb_count, th_start, programmer_th); + + for (i = 0; i < PROGRAMMER_INVALID; i++) { + const struct programmer_entry prog = programmer_table[i]; + if (prog.type == USB) { + print_supported_usbdevs_wiki_helper(prog.devices.usb); + } + } + printf("\n|}\n\n|}\n"); +} void print_supported_wiki(void) { @@ -332,41 +404,6 @@ void print_supported_wiki(void) print_supported_chipsets_wiki(3); print_supported_boards_wiki(); #endif - printf("%s%s%s", programmer_intro, th_start, programmer_th); - -#if CONFIG_NIC3COM == 1 - print_supported_pcidevs_wiki(nics_3com); -#endif -#if CONFIG_NICREALTEK == 1 - print_supported_pcidevs_wiki(nics_realtek); -#endif -#if CONFIG_NICNATSEMI == 1 - print_supported_pcidevs_wiki(nics_natsemi); -#endif -#if CONFIG_GFXNVIDIA == 1 - print_supported_pcidevs_wiki(gfx_nvidia); -#endif -#if CONFIG_DRKAISER == 1 - print_supported_pcidevs_wiki(drkaiser_pcidev); -#endif -#if CONFIG_SATASII == 1 - print_supported_pcidevs_wiki(satas_sii); -#endif -#if CONFIG_ATAHPT == 1 - print_supported_pcidevs_wiki(ata_hpt); -#endif -#if CONFIG_NICINTEL == 1 - print_supported_pcidevs_wiki(nics_intel); -#endif -#if CONFIG_NICINTEL_SPI == 1 - print_supported_pcidevs_wiki(nics_intel_spi); -#endif -#if CONFIG_OGP_SPI == 1 - print_supported_pcidevs_wiki(ogp_spi); -#endif -#if CONFIG_SATAMV == 1 - print_supported_pcidevs_wiki(satas_mv); -#endif - printf("\n|}\n\n|}\n"); + print_supported_devs_wiki(); } diff --git a/programmer.h b/programmer.h index dedec67..21fa707 100644 --- a/programmer.h +++ b/programmer.h @@ -90,9 +90,21 @@ enum programmer { PROGRAMMER_INVALID /* This must always be the last entry. */ }; +enum programmer_type { + PCI = 1, /* to detect uninitialized values */ + USB, + OTHER, +}; + struct programmer_entry { const char *vendor; const char *name; + const enum programmer_type type; + union { + const struct pcidev_status *const pci; + const struct usbdev_status *const usb; + const char *const note; + } devices; int (*init) (void); @@ -221,13 +233,6 @@ void internal_delay(int usecs); extern uint32_t io_base_addr; extern struct pci_access *pacc; extern struct pci_dev *pcidev_dev; -struct pcidev_status { - uint16_t vendor_id; - uint16_t device_id; - const enum test_state status; - const char *vendor_name; - const char *device_name; -}; uintptr_t pcidev_readbar(struct pci_dev *dev, int bar); uintptr_t pcidev_init(int bar, const struct pcidev_status *devs); /* rpci_write_* are reversible writes. The original PCI config space register @@ -244,6 +249,21 @@ int rpci_write_long(struct pci_dev *dev, int reg, uint32_t data); void print_supported_pcidevs(const struct pcidev_status *devs); #endif +struct usbdev_status { + uint16_t vendor_id; + uint16_t device_id; + const enum test_state status; + const char *vendor_name; + const char *device_name; +}; +struct pcidev_status { + uint16_t vendor_id; + uint16_t device_id; + const enum test_state status; + const char *vendor_name; + const char *device_name; +}; + #if CONFIG_INTERNAL == 1 /* board_enable.c */ int board_parse_parameter(const char *boardstring, const char **vendor, const char **model); @@ -422,13 +442,6 @@ extern const struct pcidev_status ata_hpt[]; /* ft2232_spi.c */ #if CONFIG_FT2232_SPI == 1 -struct usbdev_status { - uint16_t vendor_id; - uint16_t device_id; - const enum test_state status; - const char *vendor_name; - const char *device_name; -}; int ft2232_spi_init(void); extern const struct usbdev_status devs_ft2232spi[]; void print_supported_usbdevs(const struct usbdev_status *devs); -- Kind regards, Stefan Tauner

1 0

[PATCH 0/3] wiki patches 4.0
by Stefan Tauner 17 Nov '12

17 Nov '12

1 0

[PATCH] dediprog: Use asynchronous bulk transfers for reading
by Nico Huber 16 Nov '12

16 Nov '12

This utilizes libusb-1.0's interface for asynchronous transfers. A read is split into 512 byte chunks as required by the dediprog hardware. Up to eight chunks are scheduled for asynchronous transfer which results in a viable speed-up. First tests have shown a three times speed increase. It's based on "Bump dediprog driver to use libusb-1.0". Signed-off-by: Nico Huber <nico.huber(a)secunet.com> diff --git a/dediprog.c b/dediprog.c index a558285..f1c03d8 100644 --- a/dediprog.c +++ b/dediprog.c @@ -29,6 +29,7 @@ #define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 +#define DEDIPROG_ASYNC_TRANSFERS 8 /* at most 8 asynchronous transfers */ static libusb_context *usb_ctx; static libusb_device_handle *dediprog_handle; static int dediprog_firmwareversion; @@ -176,6 +177,38 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) return 0; } +struct dediprog_transfer_status { + int status; /* OK if 0, ERROR else */ + unsigned int queued_idx; + unsigned int finished_idx; +}; + +static void dediprog_bulk_read_cb(struct libusb_transfer *const transfer) +{ + struct dediprog_transfer_status *const status = (struct dediprog_transfer_status *)transfer->user_data; + if (transfer->status != LIBUSB_TRANSFER_COMPLETED) { + status->status = 1; + msg_perr("SPI bulk read failed!\n"); + } + ++status->finished_idx; +} + +static int dediprog_bulk_read_poll(const struct dediprog_transfer_status *const status, const int finish) +{ + if (status->finished_idx >= status->queued_idx) + return 0; + + do { + struct timeval timeout = { 10, 0 }; + const int ret = libusb_handle_events_timeout_completed(usb_ctx, &timeout, NULL); + if (ret < 0) { + msg_perr("Polling read events failed: %i %s!\n", ret, libusb_error_name(ret)); + return 1; + } + } while (finish && (status->finished_idx < status->queued_idx)); + return 0; +} + /* Bulk read interface, will read multiple 512 byte chunks aligned to 512 bytes. * @start start address * @len length @@ -184,7 +217,7 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len) { - int ret, transferred; + int ret, err = 1; unsigned int i; /* chunksize must be 512, other sizes will NOT work at all. */ const unsigned int chunksize = 0x200; @@ -194,6 +227,10 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, chunksize & 0xff, (chunksize >> 8) & 0xff }; + struct dediprog_transfer_status status = { 0, 0, 0 }; + struct libusb_transfer *transfers[DEDIPROG_ASYNC_TRANSFERS] = { NULL, }; + struct libusb_transfer *transfer; + if ((start % chunksize) || (len % chunksize)) { msg_perr("%s: Unaligned start=%i, len=%i! Please report a bug " "at flashrom(a)flashrom.org\n", __func__, start, len); @@ -214,17 +251,54 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, return 1; } - for (i = 0; i < count; i++) { - ret = libusb_bulk_transfer(dediprog_handle, 0x80 | dediprog_endpoint, - buf + i * chunksize, chunksize, &transferred, DEFAULT_TIMEOUT); - if ((ret < 0) || (transferred != chunksize)) { - msg_perr("SPI bulk read %i failed, expected %i, got %i %s!\n", - i, chunksize, ret, libusb_error_name(ret)); - return 1; + /* + * Ring buffer of bulk transfers. + * Poll until at least one transfer is ready, + * schedule next transfers until buffer is full. + */ + + /* Allocate bulk transfers. */ + for (i = 0; i < min(DEDIPROG_ASYNC_TRANSFERS, count); ++i) { + transfers[i] = libusb_alloc_transfer(0); + if (!transfers[i]) { + msg_perr("Allocating libusb transfer %i failed: %s!\n", i, libusb_error_name(ret)); + goto _err_free; } } - return 0; + /* Now transfer requested chunks using libusb's asynchronous interface. */ + while (status.queued_idx < count) { + while ((status.queued_idx - status.finished_idx) < DEDIPROG_ASYNC_TRANSFERS) { + transfer = transfers[status.queued_idx % DEDIPROG_ASYNC_TRANSFERS]; + libusb_fill_bulk_transfer(transfer, dediprog_handle, 0x80 | dediprog_endpoint, + (unsigned char *)buf + status.queued_idx * chunksize, chunksize, + dediprog_bulk_read_cb, &status, DEFAULT_TIMEOUT); + transfer->flags |= LIBUSB_TRANSFER_SHORT_NOT_OK; + ret = libusb_submit_transfer(transfer); + if (ret < 0) { + msg_perr("Submitting SPI bulk read %i failed: %i %s!\n", + status.queued_idx, ret, libusb_error_name(ret)); + goto _err_free; + } + ++status.queued_idx; + } + if (dediprog_bulk_read_poll(&status, 0)) + goto _err_free; + } + /* Wait for transfers to finish. */ + if (dediprog_bulk_read_poll(&status, 1)) + goto _err_free; + /* Check if everything has been transmitted. */ + if ((status.finished_idx < count) || status.status) + goto _err_free; + + err = 0; + +_err_free: + dediprog_bulk_read_poll(&status, 1); + for (i = 0; i < DEDIPROG_ASYNC_TRANSFERS; ++i) + if (transfers[i]) libusb_free_transfer(transfers[i]); + return err; } static int dediprog_spi_read(struct flashctx *flash, uint8_t *buf,

1 0

Re: [flashrom] Intel DH67CL verbose log
by Stefan Tauner 16 Nov '12

16 Nov '12

On Thu, 15 Nov 2012 20:31:18 +0200 Ville Herva <vherva(a)gmail.com> wrote: > Ripping the battery off for a good while helped, and I was able to upgrade > the BIOS at POST. usually there is also a jumper (CMOS or NVRAM reset) that does the same. > Anyway, it would be cool to be able to flash BIOS from Linux. that is (or was) the goal of course, but intel (and microsoft) try to block access to the flash chip more and more to have more control over what the user can run. they try to sell this as a security feature, but that is only a part of it. if it would be about security only, then the user would be in control. in the secure boot scheme on x86 machines the user IS in control about the boot loader certificates, but this is only out of fear of competition laws IMHO. ATM it IS possible to flash the BIOS region, even if other regions are locked. we just do not know if it is safe in all cases or if the management engine interferes (as this is not documented anywhere publicly) and hence give the warnings. in the future (i.e. starting with the haswell family of processors) flashrom will most probably be crippled even more on these platforms according to recently leaked information. so... nag intel please, not us ;) see also http://blogs.coreboot.org/blog/2011/08/17/gsoc-2011-flashrom-part-5-–-dear-… -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] [PATCH] Add Altera USB-Blaster SPI programmer.
by Kyösti Mälkki 16 Nov '12

16 Nov '12

On Mon, 2012-10-29 at 01:33 +0100, Stefan Tauner wrote: > Adds support for the Altera USB-Blaster programming dongle in > Active Serial (AS) mode. > Tested on both original product and a clone dongle. > > Signed-off-by: James Laird <jhl(a)mafipulation.org> > Signed-off-by: Kyösti Mälkki <kyosti.malkki(a)gmail.com> > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > --- > > Rebased on Kyösti's version. > Fixed Makefile and whitespace, cleaned up a few things, > added a manpage... please retest on hardware. > > Can someone please explain to me why send_read() does what it does? > Thanks, your clean-up looks good. Tested on both a clone with C8051F321 and the original product. The blaster design is described here: http://sourceforge.net/apps/mediawiki/urjtag/index.php?title=Cable_Altera_U… As for send_read(), to read a byte from SPI, one must first write a byte to the USB. Stupid, but that is the design. This hardware has particularly bad performance penalty when reading in small chunks of pagesize or 256 bytes. With non-blocking bulk submits in libusb-1.0, the raw read speed can be increased by factor of 2 for clone and by 5 for original product. Regards, KM

2 1

Re: [flashrom] Intel DH67CL verbose log
by Stefan Tauner 15 Nov '12

15 Nov '12

On Tue, 6 Nov 2012 22:09:13 +0200 Ville Herva <vherva(a)gmail.com> wrote: > 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. > 0x58: 0x03ff0185 FREG1: BIOS region (0x00185000-0x003fffff) is read-write. > 0x5C: 0x01840003 FREG2: WARNING: Management Engine region (0x00003000-0x00184fff) is locked. Hello Ville, thanks for your report! The problem is the locked ME region as quoted above and the SMM protection, which is both not trivial to work around, sorry. I have added the board to our list of (un)supported boards (with an appropriate note) and will commit that later together with other small changes. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] Shuttle XPC SB61G2 (FB61 mainboard) success!
by Stefan Tauner 15 Nov '12

15 Nov '12

On Sat, 3 Nov 2012 23:55:35 -0600 Lineage <lineage2005(a)gmail.com> wrote: > http://www.shuttle.eu/_archive/older/en/sb61g2.htm > This appears to be the machine based on case identifiers. > Mainboard and BIOS identifiers make it out as an FB61: > http://www.shuttle.eu/_archive/older/en/fb61.htm#mainboardfb6 > > No required switches beyond normal operations. > > Successfully wrote a new BIOS from the Manufacturer on two "identical" > systems. Only captured the log of the second machine, silly me, but the > first looked the same (at least results-wise. :D) Hello, thanks for your report! I have added your board to our list of supported hardware and will commit that later together with other small changes. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

AT25DF321A Support
by Christophe Fauvel 14 Nov '12

14 Nov '12

Hello, I am using an FT2232H mini module for flashing an AT25DF321A SPI flash under linux (Ubuntu 10.10, kernel 2.6.35-32-generic), which is supported according to your Supported Hardware list. I have tested several flashrom revisions (v0.9.2 pré-compiled, v0.9.5 and V0.9.6.xx compiled with GCC 4.4.5). * with rev0.9.2, the device is listed as UNTESTED when reading, writing or erasing. I have multiple errors when accessing the device but I can read, write and erase small amount of data. * with rev0.9.5, I also have some issues with the device, but with a few retries I am able to fully read, write and erase the chip, which is also listed as UNTESTED. * with rev0.9.6, however, the device is listed as Unknown SPI chip and I cannot access it. Have you already noticed this issue ? Best regards, -- Christophe Fauvel GOOBIE Tel: +336 76 63 93 25 +331 75 45 80 62 Mail: christophe.fauvel(a)goobie.fr Adresse: 23 avenue Louis Bréguet, Santos Dumont, 78140 Vélizy-Villacoublay FRANCE

2 1

Need help with failed flash
by simon 13 Nov '12

13 Nov '12

Flashrom: Your flash chip is in an unknown state. chipset "SiS 650" with PCI ID 1039:0650. Any sugestions please? ---- # dmidecode --type bios: <begin> # dmidecode 2.11 SMBIOS 2.3 present. Handle 0x0000, DMI type 0, 20 bytes BIOS Information Vendor: American Megatrends Inc. Version: 07.00T Release Date: 04/02/01 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 256 kB Characteristics: ISA is supported PCI is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/360 kB floppy services are supported (int 13h) 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported AGP is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Handle 0x0016, DMI type 13, 22 bytes BIOS Language Information Language Description Format: Abbreviated Installable Languages: 4 English Traditional Chinese Simplified Chinese Japanese Currently Installed Language: Not Specified <end> verbose output from flashrom: <begin> #flashrom -Vw a9280820.rom flashrom v0.9.5.2-r1517 on Linux 3.2.0-32-generic-pae (i686), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 34 usecs, 1040M loops per second, delay more than 10% too short (got 87% of expected delay), recalculating... 1187M loops per second, 10 myus = 11 us, 100 myus = 123 us, 1000 myus = 1025 us, 10000 myus = 10095 us, 136 myus = 269 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Elitegroup Co. " DMI string system-product-name: "i-Buddie " DMI string system-version: "1.0 " DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "Ref.NO:A928-020313-OT-01-00-10-FF$" DMI string baseboard-version: "2.0 " DMI string chassis-type: "Desktop" Found chipset "SiS 650" with PCI ID 1039:0650. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Found southbridge 1039:0961 at 00:02:0 OK. The following protocols are supported: Non-SPI. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x9c, id2 0x7a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Found Winbond flash chip "W49F002U/N" (256 kB, Parallel) at physical address 0xfffc0000. Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W49F002U/N" (256 kB, Parallel). Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x01ffff:EW, 0x020000-0x037fff:EW, 0x038000-0x039fff:E, 0x03a000-0x03bfff:E, 0x03c000-0x03ffff:EERASE FAILED at 0x0003c000! Expected=0xff, Read=0x9c, failed byte count from 0x0003c000-0x0003ffff: 0x3f1f ERASE FAILED! Reading current flash chip contents... done. Looking for another erase function. Trying erase function 1... 0x000000-0x03ffff:EERASE FAILED at 0x0003c000! Expected=0xff, Read=0x9c, failed byte count from 0x00000000-0x0003ffff: 0x3f1f ERASE FAILED! Looking for another erase function. No usable erase functions left. FAILED! Uh oh. Erase/write failed. Checking if anything changed. Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! Restoring PCI config space for 00:02:0 reg 0x45 Restoring PCI config space for 00:02:0 reg 0x40 <end>

1 0

[PATCH] autotest mode
by Carl-Daniel Hailfinger 11 Nov '12

11 Nov '12

This patch needs the following changes to be mergeable: - layout support - man page - message printing cosmetics Autotest mode tests all usable erase functions of a flash chip with a few test patterns, then restores the original flash contents. To make sure you can recover the original flash chip contents even if the autotest run is aborted, you have to specify a filename parameter for --autotest where the flash chip contents are saved. Example usage: flashrom -p dummy:emulate=SST25VF032B --output autotest.log --autotest scratch.img Please note that autotest uses roughly 10 erase cycles per usable erase function and repeated usage will cause serious flash wear. Speed isn't really good even with dummy, and I expect a 8 Mbit SPI chip on a real fast programmer to take at least 10 minutes for autotest (10*erasefn+1 all-sectors chip write, 10*erasefn+1.all-sectors erase, 30*erasefn+2 all-sectors read). The patch seems to work, at least during my tests with dummy. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-autotest/flash.h =================================================================== --- flashrom-autotest/flash.h (Revision 1622) +++ flashrom-autotest/flash.h (Arbeitskopie) @@ -239,7 +239,7 @@ void print_banner(void); void list_programmers_linebreak(int startcol, int cols, int paren); int selfcheck(void); -int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, int verify_it); +int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, int verify_it, int autotest_it); int read_buf_from_file(unsigned char *buf, unsigned long size, const char *filename); int write_buf_to_file(unsigned char *buf, unsigned long size, const char *filename); Index: flashrom-autotest/cli_classic.c =================================================================== --- flashrom-autotest/cli_classic.c (Revision 1622) +++ flashrom-autotest/cli_classic.c (Arbeitskopie) @@ -118,17 +118,18 @@ #if CONFIG_PRINT_WIKI == 1 int list_supported_wiki = 0; #endif - int read_it = 0, write_it = 0, erase_it = 0, verify_it = 0; + int read_it = 0, write_it = 0, erase_it = 0, verify_it = 0, autotest_it = 0; int dont_verify_it = 0, list_supported = 0, operation_specified = 0; enum programmer prog = PROGRAMMER_INVALID; int ret = 0; - static const char optstring[] = "r:Rw:v:nVEfc:l:i:p:Lzho:"; + static const char optstring[] = "r:Rw:v:a:nVEfc:l:i:p:Lzho:"; static const struct option long_options[] = { {"read", 1, NULL, 'r'}, {"write", 1, NULL, 'w'}, {"erase", 0, NULL, 'E'}, {"verify", 1, NULL, 'v'}, + {"autotest", 1, NULL, 'a'}, {"noverify", 0, NULL, 'n'}, {"chip", 1, NULL, 'c'}, {"verbose", 0, NULL, 'V'}, @@ -196,6 +197,15 @@ filename = strdup(optarg); verify_it = 1; break; + case 'a': + if (++operation_specified > 1) { + fprintf(stderr, "More than one operation " + "specified. Aborting.\n"); + cli_classic_abort_usage(); + } + filename = strdup(optarg); + autotest_it = 1; + break; case 'n': if (verify_it) { fprintf(stderr, "--verify and --noverify are" @@ -506,7 +516,7 @@ goto out_shutdown; } - if (!(read_it | write_it | verify_it | erase_it)) { + if (!(read_it || write_it || verify_it || erase_it || autotest_it)) { msg_ginfo("No operations were specified.\n"); goto out_shutdown; } @@ -520,7 +530,7 @@ * Give the chip time to settle. */ programmer_delay(100000); - ret |= doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it); + ret |= doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it, autotest_it); /* Note: doit() already calls programmer_shutdown(). */ goto out; Index: flashrom-autotest/dediprog.c =================================================================== --- flashrom-autotest/dediprog.c (Revision 1622) +++ flashrom-autotest/dediprog.c (Arbeitskopie) @@ -34,17 +34,6 @@ #define DEDI_SPI_CMD_PAGEWRITE 0x1 #define DEDI_SPI_CMD_AAIWRITE 0x4 -#if 0 -/* Might be useful for other pieces of code as well. */ -static void print_hex(void *buf, size_t len) -{ - size_t i; - - for (i = 0; i < len; i++) - msg_pdbg(" %02x", ((uint8_t *)buf)[i]); -} -#endif - /* Might be useful for other USB devices as well. static for now. */ static struct usb_device *get_device_by_vid_pid(uint16_t vid, uint16_t pid) { Index: flashrom-autotest/flashrom.c =================================================================== --- flashrom-autotest/flashrom.c (Revision 1622) +++ flashrom-autotest/flashrom.c (Arbeitskopie) @@ -448,6 +448,14 @@ return i; } +void print_hex(void *buf, size_t len) +{ + size_t i; + + for (i = 0; i < len; i++) + msg_pdbg(" %02x", ((uint8_t *)buf)[i]); +} + void tolower_string(char *str) { for (; *str != '\0'; str++) @@ -873,6 +881,9 @@ case 13: memset(buf, 0xff, size); break; + default: + msg_gerr("Invalid pattern %i\n", variant); + return 1; } if ((variant >= 0) && (variant <= 7)) { @@ -1328,8 +1339,7 @@ return 0; } -int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, - uint8_t *newcontents) +int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, uint8_t *newcontents) { int k, ret = 1; uint8_t *curcontents; @@ -1720,12 +1730,59 @@ return 0; } +int autotest_flash(struct flashctx *flash) +{ + const int patternlist[] = {0, 4, 2, 5, 1, 3, 8, 9, 13, 12}; + unsigned long size = flash->chip->total_size * 1024; + int erasefn, pattern, ret = 0; + uint8_t *oldcontents, *newcontents; + + oldcontents = malloc(size); + if (!oldcontents) { + msg_gerr("Out of memory!\n"); + exit(1); + } + newcontents = malloc(size); + if (!newcontents) { + msg_gerr("Out of memory!\n"); + exit(1); + } + msg_cinfo("Starting autotest.\n"); + /* outer loop: erase functions, inner loop: test patterns */ + for (erasefn = 0; erasefn < NUM_ERASEFUNCTIONS; erasefn++) { + msg_cdbg("Trying erase function %i... ", erasefn); + if (check_block_eraser(flash, erasefn, 1)) + continue; + for (pattern = 0; pattern < ARRAY_SIZE(patternlist); pattern++) { + msg_cinfo("Reading current flash chip contents... "); + if (flash->chip->read(flash, oldcontents, 0, size)) { + msg_cinfo("FAILED.\n"); + return 1; + } + msg_cinfo("done.\n"); + msg_cinfo("Erasing and writing flash chip... "); + if (generate_testpattern(newcontents, size, patternlist[pattern])) { + msg_gerr("Pattern %i generation failed!\n", patternlist[pattern]); + continue; + } + msg_ginfo("Writing pattern %i:\n", patternlist[pattern]); + print_hex(newcontents, 16); + ret |= walk_eraseregions(flash, erasefn, &erase_and_write_block_helper, oldcontents, + newcontents); + /* Work around chips which need some time to calm down. */ + programmer_delay(1000*1000); + ret |= verify_range(flash, newcontents, 0, size); + } + } + return ret; +} + /* This function signature is horrible. We need to design a better interface, * but right now it allows us to split off the CLI code. * Besides that, the function itself is a textbook example of abysmal code flow. */ -int doit(struct flashctx *flash, int force, const char *filename, int read_it, - int write_it, int erase_it, int verify_it) +int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, + int verify_it, int autotest_it) { uint8_t *oldcontents; uint8_t *newcontents; @@ -1744,9 +1801,11 @@ if (flash->chip->unlock) flash->chip->unlock(flash); - if (read_it) { + if (read_it || autotest_it) { ret = read_flash_to_file(flash, filename); - goto out_nofree; + /* Only quit if we are doing a pure read. */ + if (read_it) + goto out_nofree; } oldcontents = malloc(size); @@ -1802,14 +1861,27 @@ } #endif } + if (autotest_it) { + //FIXME: We completely ignore layouts in autotest mode. + autotest_flash(flash); + /* Restore original contents. */ + if (read_buf_from_file(newcontents, size, filename)) { + /* FIXME: Proper error message. */ + ret = 1; + goto out; + } + msg_ginfo("Restoring original chip contents:"); + } + + /* Read the whole chip to be able to check whether regions need to be * erased and to give better diagnostics in case write fails. * The alternative would be to read only the regions which are to be * preserved, but in that case we might perform unneeded erase which * takes time as well. */ - msg_cinfo("Reading old flash chip contents... "); + msg_cinfo("Reading current flash chip contents... "); if (flash->chip->read(flash, oldcontents, 0, size)) { ret = 1; msg_cinfo("FAILED.\n"); @@ -1817,17 +1889,19 @@ } msg_cinfo("done.\n"); - // This should be moved into each flash part's code to do it - // cleanly. This does the job. - handle_romentries(flash, oldcontents, newcontents); + /* All included romentries will be written. In autotest mode, included + * romentries will be tested with the patterns, the rest will be left + * alone. + */ + if (!autotest_it) + handle_romentries(flash, oldcontents, newcontents); - // //////////////////////////////////////////////////////////// - - if (write_it) { + if (write_it || autotest_it) { if (erase_and_write_flash(flash, oldcontents, newcontents)) { msg_cerr("Uh oh. Erase/write failed. Checking if " "anything changed.\n"); - if (!flash->chip->read(flash, newcontents, 0, size)) { + /* If this is the restore step of autotest, we want to complain in any case. */ + if (!autotest_it && !flash->chip->read(flash, newcontents, 0, size)) { if (!memcmp(oldcontents, newcontents, size)) { msg_cinfo("Good. It seems nothing was " "changed.\n"); @@ -1842,10 +1916,10 @@ } } - if (verify_it) { + if (verify_it || autotest_it) { msg_cinfo("Verifying flash... "); - if (write_it) { + if (write_it || autotest_it) { /* Work around chips which need some time to calm down. */ programmer_delay(1000*1000); ret = verify_range(flash, newcontents, 0, size); -- http://www.hailfinger.org/

2 2

Hi!
by santia.v.v 07 Nov '12

07 Nov '12

Hi! I was testing flashrom and trying tu update my BIOS and I got some problems, I entered the irc chat and very kind people helped me to send you the information you need to look at it: Here is the problem output: Here is the image for the update: http://download.gigabyte.eu/FileList/BIOS/motherboard_bios_ga-8i848p775g_f4… Here you have the output of 'flashrom -p internal -V', 'lspci -nnvvvxxx', 'superiotool -deV' : cat bios.txt flashrom v0.9.5.2-r1515 on Linux 3.6.6-gentoo (i686), built with libpci 3.1.10, GCC 4.5.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 4 usecs, 127M loops per second, delay more than 10% too short (got 53% of expected delay), recalculating... 166M loops per second, delay more than 10% too short (got 8% of expected delay), recalculating... 2138M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1007 us, 10000 myus = 10092 us, 16 myus = 17 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "8I848P775-G" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "Intel ICH5/ICH5R" with PCI ID 8086:24d0. Enabling flash write... BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: FWH. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Found SST flash chip "SST49LF002A/B" (256 kB, FWH) at physical address 0xfffc0000. Lock status for 0x000000 (size 0x004000) is 00, full access Lock status for 0x004000 (size 0x004000) is 00, full access Lock status for 0x008000 (size 0x004000) is 00, full access Lock status for 0x00c000 (size 0x004000) is 00, full access Lock status for 0x010000 (size 0x004000) is 00, full access Lock status for 0x014000 (size 0x004000) is 00, full access Lock status for 0x018000 (size 0x004000) is 00, full access Lock status for 0x01c000 (size 0x004000) is 00, full access Lock status for 0x020000 (size 0x004000) is 00, full access Lock status for 0x024000 (size 0x004000) is 00, full access Lock status for 0x028000 (size 0x004000) is 00, full access Lock status for 0x02c000 (size 0x004000) is 00, full access Lock status for 0x030000 (size 0x004000) is 00, full access Lock status for 0x034000 (size 0x004000) is 00, full access Lock status for 0x038000 (size 0x004000) is 00, full access Lock status for 0x03c000 (size 0x004000) is 00, full access Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Found SST flash chip "SST49LF002A/B" (256 kB, FWH). No operations were specified. Restoring PCI config space for 00:1f:0 reg 0x4e 00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:2570] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Capabilities: [e4] Vendor Specific Information: Len=06 <?> Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Kernel driver in use: agpgart-intel 00: 86 80 70 25 06 01 90 20 02 00 00 06 00 00 00 00 10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 70 25 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 02 08 00 40 80 1c 00 00 00 00 00 00 00 00 00 60: 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 11 00 00 00 00 00 00 00 00 00 00 0a 38 00 a0: 02 00 30 00 1b 4a 00 1f 02 03 00 00 00 00 00 00 b0: 80 00 00 00 20 00 00 00 00 00 8c 35 10 10 00 00 c0: 00 00 00 00 00 80 0e 28 00 00 00 00 00 00 00 00 d0: 02 28 04 0e 0b 0d 00 00 00 00 00 00 00 00 20 01 e0: 00 00 00 00 09 a0 06 21 06 02 00 00 00 00 00 00 f0: 00 00 00 00 02 00 00 00 68 0f 03 00 00 00 00 00 00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P AGP Bridge [8086:2571] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: f8000000-f9ffffff Prefetchable memory behind bridge: e0000000-efffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 71 25 07 00 a0 00 02 00 04 06 00 40 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 20 90 90 a0 22 20: 00 f8 f0 f9 00 e0 f0 ef 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00 00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K] 00: 86 80 76 25 02 00 80 00 02 00 80 08 00 00 00 00 10: 00 00 cf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 43 65 10 04 00 00 00 00 04 00 00 00 00 00 00 00 50: 01 00 80 00 02 01 80 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 55 05 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 20 08 00 b0: 00 00 00 00 f0 43 fc 7d 01 00 00 00 09 00 00 00 c0: 00 08 00 00 20 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 ff ff ff ff ff ff ff 3f e0: 01 00 00 00 00 00 01 02 ff 0e 00 00 00 00 04 00 f0: 00 0c 02 00 00 00 00 00 68 0f 03 00 74 fc 00 00 00:1d.0 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bc00 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 bc 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.1 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at b000 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b0 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.2 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at b400 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b4 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.3 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at b800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b8 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.7 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ehci_hcd 00: 86 80 dd 24 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 00 00 fc 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 06 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 c2 c9 00 80 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 c0 70: 00 00 d7 3f 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 55 55 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 80 00 00 88 83 40 00 66 0f 05 00 06 14 00 00 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 80000000-800fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 4e 24 07 00 80 00 c2 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 a0 a0 80 22 20: 00 fa f0 fb 00 80 00 80 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 40: 02 28 30 76 00 00 00 00 00 00 00 00 00 00 00 00 50: 26 64 73 00 00 00 00 00 50 01 34 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 b8 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 4f 35 00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 10 00 00 10 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 81 10 00 00 10 00 00 00 60: 8c 89 8b 8a d0 00 00 00 8a 80 80 8b 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 75 54 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 20 02 00 00 00 00 00 00 0d 00 00 00 00 03 00 00 b0: 00 00 00 00 00 00 00 00 55 65 55 59 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 80 08 00 30 00 00 d0: 86 21 02 00 02 0f 00 00 04 00 00 00 00 00 00 00 e0: 10 00 00 c0 00 00 0f 34 33 22 11 00 00 00 67 45 f0: 00 00 62 00 04 00 00 00 66 0f 05 3e 00 00 00 00 00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d1] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 Region 4: I/O ports at f000 [size=16] Kernel driver in use: ata_piix 00: 86 80 d1 24 05 00 a8 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 20: 01 f0 00 00 00 00 00 00 00 00 00 00 58 14 d1 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40: 07 a3 03 e3 00 00 00 00 05 00 01 02 00 00 00 00 50: 00 00 00 00 f0 10 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 04 00 13 00 20 00 00 00 00 00 00 00 00 00 00 00 a0: 68 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 1400 [size=32] Kernel driver in use: i801_smbus 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 14 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 02 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV635 PRO AGP [Radeon HD 3650] [1002:9596] (prog-if 00 [VGA controller]) Subsystem: Hightech Information System Ltd. Device [1787:0028] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at f9000000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at f8000000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Kernel driver in use: radeon 00: 02 10 96 95 07 00 b0 02 00 00 00 03 08 20 00 00 10: 08 00 00 e0 01 90 00 00 00 00 00 f9 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 28 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 01 08 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 28 00 50: 01 58 03 06 00 00 00 00 02 00 30 00 1b 02 00 ff 60: 02 43 00 1f 01 0d 00 00 00 00 01 11 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:03.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 0a) Subsystem: Creative Labs Live! 5.1 Digital [SB0228] [1102:8066] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at a000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: snd_emu10k1 Kernel modules: snd-emu10k1 00: 02 11 02 00 05 00 90 02 0a 00 01 04 00 20 80 00 10: 01 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 66 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0c 01 02 14 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 06 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:03.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 0a) Subsystem: Creative Labs Gameport Joystick [1102:0020] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Region 0: I/O ports at a400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 70 05 00 90 02 0a 00 80 09 00 20 80 00 10: 01 a4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 06 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:04.0 Ethernet controller [0200]: Atheros Communications Inc. AR2413/AR2414 Wireless Network Adapter [AR5005G(S) 802.11bg] [168c:001a] (rev 01) Subsystem: Accton Technology Corporation Device [1113:4211] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: ath5k Kernel modules: ath5k 00: 8c 16 1a 00 06 00 90 02 01 00 00 02 08 a8 00 00 10: 00 00 00 fb 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 01 50 00 00 13 11 11 42 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 0a 1c 40: 00 00 00 00 01 00 c2 01 00 40 00 c6 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:09.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13) Subsystem: Giga-byte Technology Marvell 88E8001 Gigabit Ethernet Controller (Gigabyte) [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fb010000 (32-bit, non-prefetchable) [size=16K] Region 1: I/O ports at a800 [size=256] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=7 DScale=1 PME- Capabilities: [50] Vital Product Data Product Name: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter Read-only fields: [PN] Part number: Yukon 88E8001 [EC] Engineering changes: Rev. 1.3 [MN] Manufacture ID: 4d 61 72 76 65 6c 6c [SN] Serial number: AbCdEfG4f7639 [CP] Extended capability: 01 10 cc 03 [RV] Reserved: checksum good, 10 byte(s) reserved Read/write fields: [RW] Read-write area: 121 byte(s) free End Kernel driver in use: skge 00: ab 11 20 43 07 00 b0 02 13 00 00 02 08 40 00 00 10: 00 00 01 fb 01 a8 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 00 e0 30: 00 00 00 00 48 00 00 00 00 00 00 00 0a 01 17 1f 40: 00 00 f0 05 00 80 a0 01 01 50 02 fe 00 2e 00 0c 50: 03 00 fc 80 00 00 00 78 00 00 04 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Found ITE IT8712F (id=0x8712, rev=0x5) at 0x2e Register dump: idx 20 21 22 23 24 2b val 87 12 05 00 00 00 def 87 12 08 00 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 00 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 f1 f2 f3 val 01 03 f8 04 00 50 00 7f def 00 03 f8 04 00 50 00 7f LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 01 02 f8 03 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 70 74 f0 val 01 03 78 00 00 07 04 08 def 00 03 78 07 78 07 03 03 LDN 0x04 (Environment controller) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 01 02 90 00 00 00 80 00 0a 00 00 00 ff def 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 71 f0 val 01 00 60 00 64 01 02 68 def 01 00 60 00 64 01 02 08 LDN 0x06 (Mouse) idx 30 70 71 f0 val 00 00 02 00 def 00 0c 02 00 LDN 0x07 (GPIO) idx 25 26 27 28 29 2a 2c 60 61 62 63 64 65 70 71 72 73 74 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c8 c9 ca cb cc e0 e1 e2 e3 e4 f0 f1 f2 f3 f4 f5 f6 f7 f8 f9 fa fb fc fd val 01 00 20 01 a1 00 00 00 00 08 00 00 00 00 00 00 00 04 00 00 00 00 00 00 01 00 20 01 21 21 01 00 00 00 20 01 00 00 00 20 00 00 00 00 00 10 40 00 00 00 28 1d 00 00 00 00 00 1f 00 def 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40 00 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 03 00 0a 00 def 00 03 00 0a 00 LDN 0x09 (Game port) idx 30 60 61 val 00 02 01 def 00 02 01 LDN 0x0a (Consumer IR) idx 30 60 61 70 f0 val 00 03 10 0b 06 def 00 03 10 0b 00 Environment controller (0x0295) Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff

1 1

Intel DH67CL verbose log
by Ville Herva 06 Nov '12

06 Nov '12

Seems not to be supported. -- v -- v(a)iki.fi

1 0

Re: [flashrom] [PATCH] Add board enable for Asus DSAN-DX.
by Stefan Tauner 05 Nov '12

05 Nov '12

On Mon, 29 Oct 2012 23:32:42 +0100 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> wrote: > IDs are from the host bridge and LPC controller. The enable function > was reverse engineered by roxfan, thanks! > > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Since mezzo did not report back, i have committed the untested board enable in r1622. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[commit] r1622 - trunk
by repository service 05 Nov '12

05 Nov '12

Author: stefanct Date: Mon Nov 5 13:20:29 2012 New Revision: 1622 URL: http://flashrom.org/trac/flashrom/changeset/1622 Log: Add (untested) board enable for Asus DSAN-DX. IDs are from the host bridge and LPC controller. The enable function was reverse engineered by roxfan, thanks! User mezzo vanished without reporting any test results. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Fri Nov 2 00:38:51 2012 (r1621) +++ trunk/board_enable.c Mon Nov 5 13:20:29 2012 (r1622) @@ -1823,6 +1823,7 @@ /* * Suited for: + * - ASUS DSAN-DX * - P4SD-LA (HP OEM): i865 + ICH5 * - GIGABYTE GA-8IP775: 865P + ICH5 * - GIGABYTE GA-8PE667 Ultra 2: socket 478 + i845PE + ICH4 @@ -2335,6 +2336,7 @@ {0x10DE, 0x0260, 0x103C, 0x2A34, 0x10DE, 0x0264, 0x103C, 0x2A34, "NODUSM3", NULL, NULL, P3, "ASUS", "A8M2N-LA (NodusM3-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, {0x10DE, 0x0260, 0x103c, 0x2a3e, 0x10DE, 0x0264, 0x103c, 0x2a3e, "NAGAMI2L", NULL, NULL, P3, "ASUS", "A8N-LA (Nagami-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, {0x10de, 0x0264, 0x1043, 0x81bc, 0x10de, 0x02f0, 0x1043, 0x81cd, NULL, NULL, NULL, P3, "ASUS", "A8N-VM CSM", 0, OK, w83627ehf_gpio22_raise_2e}, + {0x8086, 0x65c0, 0x1043, 0x8301, 0x8086, 0x2916, 0x1043, 0x82a6, "^DSAN-DX$", NULL, NULL, P3, "ASUS", "DSAN-DX", 0, NT, intel_ich_gpio32_raise}, {0x10DE, 0x0264, 0x1043, 0x81C0, 0x10DE, 0x0260, 0x1043, 0x81C0, NULL, NULL, NULL, P3, "ASUS", "M2NBP-VM CSM", 0, OK, nvidia_mcp_gpio0_raise}, {0x1106, 0x1336, 0x1043, 0x80ed, 0x1106, 0x3288, 0x1043, 0x8249, NULL, NULL, NULL, P3, "ASUS", "M2V-MX", 0, OK, via_vt823x_gpio5_raise}, {0x8086, 0x24cc, 0, 0, 0x8086, 0x24c3, 0x1043, 0x1869, "^M6Ne$", NULL, NULL, P3, "ASUS", "M6Ne", 0, NT, intel_ich_gpio43_raise}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Fri Nov 2 00:38:51 2012 (r1621) +++ trunk/print.c Mon Nov 5 13:20:29 2012 (r1622) @@ -634,6 +634,7 @@ B("ASUS", "A8V-E SE", OK, "http://www.asus.com/Motherboards/AMD_Socket_939/A8VE_SE/", "See http://www.coreboot.org/pipermail/coreboot/2007-October/026496.html"), B("ASUS", "Crosshair II Formula", OK, "http://www.asus.com/Motherboards/AMD_AM2Plus/Crosshair_II_Formula/", NULL), B("ASUS", "Crosshair IV Extreme", OK, "http://www.asus.com/Motherboards/AMD_AM3/Crosshair_IV_Extreme/", NULL), + B("ASUS", "DSAN-DX", NT, "http://www.asus.com/Server_Workstation/Server_Motherboards/DSANDX/", NULL), B("ASUS", "E35M1-I DELUXE", OK, "http://www.asus.com/Motherboards/AMD_CPU_on_Board/E35M1I_DELUXE/", NULL), B("ASUS", "K8N", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8N/", NULL), B("ASUS", "K8V", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8V/", NULL),

1 0

flashrom -V
by Martin Haag 1 05 Nov '12

05 Nov '12

Thanks for the Program. Hops the output helps for further developing. best regards Martin Fa. Haag Martin Haag Kommunikationstechnik Libanonstrasse 37 70184 Stuttgart Tel.: 0711/4895033 Fax: 0711/4895066 E-Mail: martin(a)fa-haag.de

1 0

Modded Bios
by Michael Card 04 Nov '12

04 Nov '12

Hi there I am trying to follow the instructions to save my Bios to disk using DPCIManager… It never saves a file? I have an Asrock H77 Pro4-M Motherboard. Could you help me save/edit/flash a modded bios to this board? Thx Michael Card

2 1

Shuttle XPC SB61G2 (FB61 mainboard) success!
by Lineage 04 Nov '12

04 Nov '12

http://www.shuttle.eu/_archive/older/en/sb61g2.htm This appears to be the machine based on case identifiers. Mainboard and BIOS identifiers make it out as an FB61: http://www.shuttle.eu/_archive/older/en/fb61.htm#mainboardfb6 No required switches beyond normal operations. Successfully wrote a new BIOS from the Manufacturer on two "identical" systems. Only captured the log of the second machine, silly me, but the first looked the same (at least results-wise. :D) ----8<---- flashrom --version ---->8---- flashrom v0.9.2-r1141 on Linux 2.6.32-5-686 (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian ----8<---- flashrom -V log ---->8---- Calibrating delay loop... OS timer resolution is 1 usecs, 2002M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1004 us, 10000 myus = 10004 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Shuttle Inc" DMI string system-product-name: "SB61V40" DMI string system-version: " " DMI string baseboard-manufacturer: "Shuttle Inc" DMI string baseboard-product-name: "FB61V40" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8712 Found chipset "Intel ICH5/ICH5R", enabling flash write... chipset PCI ID is 8086:24d0, BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 OK. This chipset supports the following protocols: FWH. Super I/O ID 0x8712 is not on the list of flash capable controllers. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: skipped. Probing for AMIC A25L05PU, 64 KB: skipped. Probing for AMIC A25L10PT, 128 KB: skipped. Probing for AMIC A25L10PU, 128 KB: skipped. Probing for AMIC A25L20PT, 256 KB: skipped. Probing for AMIC A25L20PU, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A25L80P, 1024 KB: skipped. Probing for AMIC A25L16PT, 2048 KB: skipped. Probing for AMIC A25L16PU, 2048 KB: skipped. Probing for AMIC A25L512, 64 KB: skipped. Probing for AMIC A25L010, 128 KB: skipped. Probing for AMIC A25L020, 256 KB: skipped. Probing for AMIC A25L040, 512 KB: skipped. Probing for AMIC A25L080, 1024 KB: skipped. Probing for AMIC A25L016, 2048 KB: skipped. Probing for AMIC A25L032, 4096 KB: skipped. Probing for AMIC A25LQ032, 4096 KB: skipped. Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF081A, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25DQ161, 2048 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F002BC-T, 256 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF064C, 8192 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25LF040A.RES, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Lock status for 0x000000 (size 0x010000) is 01, write locked Lock status for 0x010000 (size 0x010000) is 01, write locked Lock status for 0x020000 (size 0x010000) is 01, write locked Lock status for 0x030000 (size 0x010000) is 01, write locked Lock status for 0x040000 (size 0x010000) is 01, write locked Lock status for 0x050000 (size 0x010000) is 01, write locked Lock status for 0x060000 (size 0x010000) is 01, write locked Lock status for 0x070000 (size 0x010000) is 01, write locked Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xe5, id2 0xa7, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25Q64, 8192 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for AMIC unknown AMIC SPI chip, 0 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for Eon unknown Eon SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. No operations were specified. ----8<---- flashrom -w log ---->8---- Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, id 8712 Found chipset "Intel ICH5/ICH5R", enabling flash write... OK. This chipset supports the following protocols: FWH. Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... SUCCESS. Programming page: address: 0x00000000address: 0x00001000address: 0x00002000address: 0x00003000address: 0x00004000address: 0x00005000address: 0x00006000address: 0x00007000address: 0x00008000address: 0x00009000address: 0x0000a000address: 0x0000b000address: 0x0000c000address: 0x0000d000address: 0x0000e000address: 0x0000f000address: 0x00010000address: 0x00011000address: 0x00012000address: 0x00013000address: 0x00014000address: 0x00015000address: 0x00016000address: 0x00017000address: 0x00018000address: 0x00019000address: 0x0001a000address: 0x0001b000address: 0x0001c000address: 0x0001d000address: 0x0001e000address: 0x0001f000address: 0x00020000address: 0x00021000address: 0x00022000address: 0x00023000address: 0x00024000address: 0x00025000address: 0x00026000address: 0x00027000address: 0x00028000address: 0x00029000address: 0x0002a000address: 0x0002b000address: 0x0002c000address: 0x0002d000address: 0x0002e000address: 0x0002f000address: 0x00030000address: 0x00031000address: 0x00032000address: 0x00033000address: 0x00034000address: 0x00035000address: 0x00036000address: 0x00037000address: 0x00038000address: 0x00039000address: 0x0003a000address: 0x0003b000address: 0x0003c000address: 0x0003d000address: 0x0003e000address: 0x0003f000address: 0x00040000address: 0x00041000address: 0x00042000address: 0x00043000address: 0x00044000address: 0x00045000address: 0x00046000address: 0x00047000address: 0x00048000address: 0x00049000address: 0x0004a000address: 0x0004b000address: 0x0004c000address: 0x0004d000address: 0x0004e000address: 0x0004f000address: 0x00050000address: 0x00051000address: 0x00052000address: 0x00053000address: 0x00054000address: 0x00055000address: 0x00056000address: 0x00057000address: 0x00058000address: 0x00059000address: 0x0005a000address: 0x0005b000address: 0x0005c000address: 0x0005d000address: 0x0005e000address: 0x0005f000address: 0x00060000address: 0x00061000address: 0x00062000address: 0x00063000address: 0x00064000address: 0x00065000address: 0x00066000address: 0x00067000address: 0x00068000address: 0x00069000address: 0x0006a000address: 0x0006b000address: 0x0006c000address: 0x0006d000address: 0x0006e000address: 0x0006f000address: 0x00070000address: 0x00071000address: 0x00072000address: 0x00073000address: 0x00074000address: 0x00075000address: 0x00076000address: 0x00077000address: 0x00078000address: 0x00079000address: 0x0007a000address: 0x0007b000address: 0x0007c000address: 0x0007d000address: 0x0007e000address: 0x0007f000DONE! COMPLETE. Verifying flash... VERIFIED. The BIOS update didn't give me the functionality (USB HDD boot) I am looking for, so these machines will be a project for coreboot and I will be happy to test newer releases until I get bored with the machines. Cheers and thanks for a wonderful tool! Milo

1 0

W836xx: A7N8X: flashrom -V
by Andrew Savchenko 04 Nov '12

04 Nov '12

flashrom v0.9.6.1-r1564 on Linux 3.3.8-yoruichi (i686) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.6.3, little endian Command line (3 args): flashrom -p internal -V Calibrating delay loop... OS timer resolution is 1 usecs, 834M loops per second, delay more than 10% too short (got 76% of expected delay), recalculating... 824M loops per second, delay more than 10% too short (got 75% of expected delay), recalculating... 820M loops per second, 10 myus = 11 us, 100 myus = 112 us, 1000 myus = 2595 us, 10000 myus = 8875 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "ASUSTeK Computer INC." DMI string system-product-name: "A7N8X2.0" DMI string system-version: "REV 2.xx" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "A7N8X2.0" DMI string baseboard-version: "REV 2.xx" DMI string chassis-type: "Desktop" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 87. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE Super I/O, ID 0x8708 on port 0x2e Found chipset "NVIDIA NForce2" with PCI ID 10de:0060. Enabling flash write... OK. Super I/O ID 0x8708 is not on the list of flash capable controllers. The following protocols are supported: Non-SPI. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Atmel AT49F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29LV640B, 8192 kB: probe_en29lv640b: id1 0xffff, id2 0x00ff Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV512, 64 kB: probe_jedec_common: id1 0x5d, id2 0x19, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Found PMC flash chip "Pm49FL002" (256 kB, LPC, FWH) at physical address 0xfffc0000. Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0xff, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x5d, id2 0x19, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0x25, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x9d, id2 0x6d Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found PMC flash chip "Pm49FL002" (256 kB, LPC, FWH). No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x92

1 0

Problem with writing BIOS
by dask 02 Nov '12

02 Nov '12

Hello I have a problem with writing BIOS I googled but nothing help me. Here is the log. May be you can help me. Thank you. sudo flashrom -p internal -w 668F1P48.BIN flashrom v0.9.6.1-r1563 on Linux 3.5.0-17-generic (i686) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "Intel ICH7/ICH7R". Enabling flash write... OK. Found PMC flash chip "Pm49FL004" (512 kB, LPC, FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x25, failed byte count from 0x00000000-0x00000fff: 0xff7 ERASE FAILED! Reading current flash chip contents... done. ERASE FAILED at 0x00000000! Expected=0xff, Read=0x25, failed byte count from 0x00000000-0x0000ffff: 0xff00 ERASE FAILED! Reading current flash chip contents... done. ERASE FAILED at 0x00000000! Expected=0xff, Read=0x25, failed byte count from 0x00000000-0x0007ffff: 0x610d0 ERASE FAILED! FAILED! Uh oh. Erase/write failed. Checking if anything changed. Good. It seems nothing was changed. Writing to the flash chip apparently didn't do anything. This means we have to add special support for your board, programmer or flash chip. Please report this on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! -- Best regards, Erik

2 2

[PATCH] Bus Pirate UART speedup
by Carl-Daniel Hailfinger 02 Nov '12

02 Nov '12

Increase PIC/FT232 UART speed to 2 Mbaud (instead of 115200 baud) in firmware 5.5 and newer. Given that UART speed is the biggest bottleneck for Bus Pirate communication (right now 90% of the read time is caused by slow BP<->host communication), this patch is absolutely needed to get any decent speed out of the Bus Pirate. WARNING: This patch may hang flashrom or corrupt data for any non-v3 Bus Pirate model. I haven't tested such models, and it might work without problems. Who knows. We would have to find someone with a v2 (or earlier) Bus Pirate and a firmware version >=v5.5 to test this. For Bus Pirate model v4 this patch may be completely superfluous. Anyway, activating fast UART only for some models is probably the way to go. We already have code to determine the hardware model in the init function, this just needs to be stored in some variable. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-buspirate_serialspeedup/buspirate_spi.c =================================================================== --- flashrom-buspirate_serialspeedup/buspirate_spi.c (revision 1621) +++ flashrom-buspirate_serialspeedup/buspirate_spi.c (working copy) @@ -179,6 +179,7 @@ /* Reset Bus Pirate (return to user terminal) */ bp_commbuf[0] = 0x0f; ret = buspirate_sendrecv(bp_commbuf, 1, 0); + sp_serport_changebaud(115200); out_shutdown: /* Shut down serial port communication */ @@ -354,6 +355,44 @@ spi_programmer_buspirate.command = buspirate_spi_send_command_v1; } + /* Increase PIC/FT232 UART speed to 2 Mbaud (instead of 115200 baud) in firmware 5.5 and newer. + * Although this is already possible in firmware 5.2, fast UART in combination with the old SPI + * command set causes hangs for bigger transactions. This is caused by a UART buffer overrun + * in the PIC, and all firmware versions up to (hopefully not including) 6.2 are affected. + */ + if (BP_FWVERSION(fw_version_major, fw_version_minor) >= BP_FWVERSION(5, 5)) { + // FIXME: Do this only for USB-based Bus Pirates... unless you're sure the UART can handle more. + int cmdlen; + /* Request setting the UART baud rate. */ + cmdlen = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "b\n"); + if ((ret = buspirate_sendrecv(bp_commbuf, cmdlen, 0))) + return ret; + if ((ret = buspirate_wait_for_string(bp_commbuf, ">"))) + return ret; + /* Request setting the UART clock divisor manually. */ + cmdlen = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "10\n"); + if ((ret = buspirate_sendrecv(bp_commbuf, cmdlen, 0))) + return ret; + if ((ret = buspirate_wait_for_string(bp_commbuf, ">"))) + return ret; + /* Set the UART clock divisor. New clock is 4000000/(divisor+1). */ + cmdlen = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "%i\n", 1); + if ((ret = buspirate_sendrecv(bp_commbuf, cmdlen, 0))) + return ret; + sleep(1); + sp_serport_changebaud(2000000); + bp_commbuf[0] = ' '; + if ((ret = buspirate_sendrecv(bp_commbuf, 1, 0))) + return ret; + if ((ret = buspirate_wait_for_string(bp_commbuf, "HiZ>"))) + return ret; + msg_pdbg("Using fast 2 Mbaud for Bus Pirate <-> host communication.\n"); + } else { + msg_pinfo("Bus Pirate firmware 5.4 and older does not support fast Bus Pirate <-> host " + "communication. Limiting UART speed to 115200 Baud.\n"); + msg_pinfo("It is recommended to upgrade to firmware 6.2 or newer.\n"); + } + /* Workaround for broken speed settings in firmware 6.1 and older. */ if (BP_FWVERSION(fw_version_major, fw_version_minor) < BP_FWVERSION(6, 2)) if (spispeed > 0x4) { Index: flashrom-buspirate_serialspeedup/serial.c =================================================================== --- flashrom-buspirate_serialspeedup/serial.c (revision 1621) +++ flashrom-buspirate_serialspeedup/serial.c (working copy) @@ -104,6 +104,28 @@ }; #endif +int sp_serport_changebaud(unsigned int baud) +{ + struct termios options; + int i; + + tcgetattr(sp_fd, &options); + for (i = 0;; i++) { + if (sp_baudtable[i].baud == 0) { + close(sp_fd); + msg_perr("Error: cannot configure for baudrate %d\n", baud); + exit(1); + } + if (sp_baudtable[i].baud == baud) { + cfsetispeed(&options, sp_baudtable[i].flag); + cfsetospeed(&options, sp_baudtable[i].flag); + break; + } + } + tcsetattr(sp_fd, TCSANOW, &options); + return 0; +} + fdtype sp_openserport(char *dev, unsigned int baud) { #ifdef _WIN32 Index: flashrom-buspirate_serialspeedup/programmer.h =================================================================== --- flashrom-buspirate_serialspeedup/programmer.h (revision 1621) +++ flashrom-buspirate_serialspeedup/programmer.h (working copy) @@ -644,6 +644,7 @@ void sp_flush_incoming(void); fdtype sp_openserport(char *dev, unsigned int baud); +int sp_serport_changebaud(unsigned int baud); void __attribute__((noreturn)) sp_die(char *msg); extern fdtype sp_fd; /* expose serialport_shutdown as it's currently used by buspirate */ -- http://www.hailfinger.org/

1 0

Re: [flashrom] [PATCH] Bus Pirate: Speedup and firmware workarounds
by Carl-Daniel Hailfinger 02 Nov '12

02 Nov '12

Am 15.07.2012 21:28 schrieb Idwer Vollering: > 2012/6/13 Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>: >> > Bus Pirate Firmware v5.5 and newer support a new SPI binary mode. Use it >> > if available. >> > Bus Pirate Firmware v6.1 and older have broken (too slow) SPI clock >> > divisor for any requested speed above 2 MHz. Force a downgrade to 2 MHz >> > for affected firmware versions. >> > flashrom will recommend to upgrade the Bus Pirate Firmware if it is >> > older than v6.2. >> > >> > Somewhat tested, code still needs to be cleaned up in a few spots. > Tested with reading/erasing/writing a MX25L1605 on a Thinkpad X60 > mainboard, using buspirate hardware v3.a running firmware v6.2-test > that can be found here (bp-spifix.zip): > http://dangerousprototypes.com/forum/viewtopic.php?f=40&t=3864&sid=426d3213… Thanks for the comments! There are indeed quite a few magic constants, and replacing them with #defines makes sense. That's something I'd leave to another patch, though. New version. Support the new fast SPI mode present in Bus Pirate firmware v5.5 or newer. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-buspirate_newcommands/buspirate_spi.c =================================================================== --- flashrom-buspirate_newcommands/buspirate_spi.c (Revision 1620) +++ flashrom-buspirate_newcommands/buspirate_spi.c (Arbeitskopie) @@ -1,7 +1,7 @@ /* * This file is part of the flashrom project. * - * Copyright (C) 2009, 2010 Carl-Daniel Hailfinger + * Copyright (C) 2009, 2010, 2011, 2012 Carl-Daniel Hailfinger * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -129,14 +129,16 @@ return ret; } -static int buspirate_spi_send_command(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, - const unsigned char *writearr, unsigned char *readarr); +static int buspirate_spi_send_command_v1(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); +static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); -static const struct spi_programmer spi_programmer_buspirate = { +static struct spi_programmer spi_programmer_buspirate = { .type = SPI_CONTROLLER_BUSPIRATE, - .max_data_read = 12, - .max_data_write = 12, - .command = buspirate_spi_send_command, + .max_data_read = MAX_DATA_UNSPECIFIED, + .max_data_write = MAX_DATA_UNSPECIFIED, + .command = NULL, .multicommand = default_spi_send_multicommand, .read = default_spi_read, .write_256 = default_spi_write_256, @@ -253,7 +255,11 @@ if (register_shutdown(buspirate_spi_shutdown, NULL)) return 1; - /* This is the brute force version, but it should work. */ + /* This is the brute force version, but it should work. + * It is likely to fail if a previous flashrom run was aborted during a write with the new SPI commands + * in firmware v5.5 because that firmware may wait for up to 4096 bytes of input before responding to + * 0x00 again. The obvious workaround (sending 4096 bytes of \0) may cause significant startup delays. + */ for (i = 0; i < 20; i++) { /* Enter raw bitbang mode */ bp_commbuf[0] = 0x00; @@ -327,6 +333,27 @@ return SPI_PROGRAMMER_ERROR; } + /* Use fast SPI mode in firmware 5.5 and newer. */ + if (BP_FWVERSION(fw_version_major, fw_version_minor) >= BP_FWVERSION(5, 5)) { + msg_pdbg("Using SPI command set v2.\n"); + /* Sensible default buffer size. */ + if (buspirate_commbuf_grow(260 + 5)) + return ERROR_OOM; + spi_programmer_buspirate.max_data_read = 2048; + spi_programmer_buspirate.max_data_write = 256; + spi_programmer_buspirate.command = buspirate_spi_send_command_v2; + } else { + msg_pinfo("Bus Pirate firmware 5.4 and older does not support fast SPI access.\n"); + msg_pinfo("Reading/writing a flash chip may take hours.\n"); + msg_pinfo("It is recommended to upgrade to firmware 5.5 or newer.\n"); + /* Sensible default buffer size. */ + if (buspirate_commbuf_grow(16 + 3)) + return ERROR_OOM; + spi_programmer_buspirate.max_data_read = 12; + spi_programmer_buspirate.max_data_write = 12; + spi_programmer_buspirate.command = buspirate_spi_send_command_v1; + } + /* Workaround for broken speed settings in firmware 6.1 and older. */ if (BP_FWVERSION(fw_version_major, fw_version_minor) < BP_FWVERSION(6, 2)) if (spispeed > 0x4) { @@ -412,11 +439,8 @@ return 0; } -static int buspirate_spi_send_command(struct flashctx *flash, - unsigned int writecnt, - unsigned int readcnt, - const unsigned char *writearr, - unsigned char *readarr) +static int buspirate_spi_send_command_v1(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr) { unsigned int i = 0; int ret = 0; @@ -467,3 +491,43 @@ return ret; } + +static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr) +{ + int i = 0, ret = 0; + + if (writecnt > 4096 || readcnt > 4096 || (readcnt + writecnt) > 4096) + return SPI_INVALID_LENGTH; + + /* 5 bytes extra for command, writelen, readlen. + * 1 byte extra for Ack/Nack. + */ + if (buspirate_commbuf_grow(max(writecnt + 5, readcnt + 1))) + return ERROR_OOM; + + /* Combined SPI write/read. */ + bp_commbuf[i++] = 0x04; + bp_commbuf[i++] = (writecnt >> 8) & 0xff; + bp_commbuf[i++] = writecnt & 0xff; + bp_commbuf[i++] = (readcnt >> 8) & 0xff; + bp_commbuf[i++] = readcnt & 0xff; + memcpy(bp_commbuf + i, writearr, writecnt); + + ret = buspirate_sendrecv(bp_commbuf, i + writecnt, 1 + readcnt); + + if (ret) { + msg_perr("Bus Pirate communication error!\n"); + return SPI_GENERIC_ERROR; + } + + if (bp_commbuf[0] != 0x01) { + msg_perr("Protocol error while sending SPI write/read!\n"); + return SPI_GENERIC_ERROR; + } + + /* Skip Ack. */ + memcpy(readarr, bp_commbuf + 1, readcnt); + + return ret; +} -- http://www.hailfinger.org/

1 1

[commit] r1621 - trunk
by repository service 02 Nov '12

02 Nov '12

Author: hailfinger Date: Fri Nov 2 00:38:51 2012 New Revision: 1621 URL: http://flashrom.org/trac/flashrom/changeset/1621 Log: Support the new fast SPI mode present in Bus Pirate firmware v5.5 or newer. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/buspirate_spi.c Modified: trunk/buspirate_spi.c ============================================================================== --- trunk/buspirate_spi.c Sun Oct 28 02:50:08 2012 (r1620) +++ trunk/buspirate_spi.c Fri Nov 2 00:38:51 2012 (r1621) @@ -1,7 +1,7 @@ /* * This file is part of the flashrom project. * - * Copyright (C) 2009, 2010 Carl-Daniel Hailfinger + * Copyright (C) 2009, 2010, 2011, 2012 Carl-Daniel Hailfinger * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -129,14 +129,16 @@ return ret; } -static int buspirate_spi_send_command(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, - const unsigned char *writearr, unsigned char *readarr); +static int buspirate_spi_send_command_v1(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); +static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); -static const struct spi_programmer spi_programmer_buspirate = { +static struct spi_programmer spi_programmer_buspirate = { .type = SPI_CONTROLLER_BUSPIRATE, - .max_data_read = 12, - .max_data_write = 12, - .command = buspirate_spi_send_command, + .max_data_read = MAX_DATA_UNSPECIFIED, + .max_data_write = MAX_DATA_UNSPECIFIED, + .command = NULL, .multicommand = default_spi_send_multicommand, .read = default_spi_read, .write_256 = default_spi_write_256, @@ -253,7 +255,11 @@ if (register_shutdown(buspirate_spi_shutdown, NULL)) return 1; - /* This is the brute force version, but it should work. */ + /* This is the brute force version, but it should work. + * It is likely to fail if a previous flashrom run was aborted during a write with the new SPI commands + * in firmware v5.5 because that firmware may wait for up to 4096 bytes of input before responding to + * 0x00 again. The obvious workaround (sending 4096 bytes of \0) may cause significant startup delays. + */ for (i = 0; i < 20; i++) { /* Enter raw bitbang mode */ bp_commbuf[0] = 0x00; @@ -327,6 +333,27 @@ return SPI_PROGRAMMER_ERROR; } + /* Use fast SPI mode in firmware 5.5 and newer. */ + if (BP_FWVERSION(fw_version_major, fw_version_minor) >= BP_FWVERSION(5, 5)) { + msg_pdbg("Using SPI command set v2.\n"); + /* Sensible default buffer size. */ + if (buspirate_commbuf_grow(260 + 5)) + return ERROR_OOM; + spi_programmer_buspirate.max_data_read = 2048; + spi_programmer_buspirate.max_data_write = 256; + spi_programmer_buspirate.command = buspirate_spi_send_command_v2; + } else { + msg_pinfo("Bus Pirate firmware 5.4 and older does not support fast SPI access.\n"); + msg_pinfo("Reading/writing a flash chip may take hours.\n"); + msg_pinfo("It is recommended to upgrade to firmware 5.5 or newer.\n"); + /* Sensible default buffer size. */ + if (buspirate_commbuf_grow(16 + 3)) + return ERROR_OOM; + spi_programmer_buspirate.max_data_read = 12; + spi_programmer_buspirate.max_data_write = 12; + spi_programmer_buspirate.command = buspirate_spi_send_command_v1; + } + /* Workaround for broken speed settings in firmware 6.1 and older. */ if (BP_FWVERSION(fw_version_major, fw_version_minor) < BP_FWVERSION(6, 2)) if (spispeed > 0x4) { @@ -412,11 +439,8 @@ return 0; } -static int buspirate_spi_send_command(struct flashctx *flash, - unsigned int writecnt, - unsigned int readcnt, - const unsigned char *writearr, - unsigned char *readarr) +static int buspirate_spi_send_command_v1(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr) { unsigned int i = 0; int ret = 0; @@ -467,3 +491,43 @@ return ret; } + +static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr) +{ + int i = 0, ret = 0; + + if (writecnt > 4096 || readcnt > 4096 || (readcnt + writecnt) > 4096) + return SPI_INVALID_LENGTH; + + /* 5 bytes extra for command, writelen, readlen. + * 1 byte extra for Ack/Nack. + */ + if (buspirate_commbuf_grow(max(writecnt + 5, readcnt + 1))) + return ERROR_OOM; + + /* Combined SPI write/read. */ + bp_commbuf[i++] = 0x04; + bp_commbuf[i++] = (writecnt >> 8) & 0xff; + bp_commbuf[i++] = writecnt & 0xff; + bp_commbuf[i++] = (readcnt >> 8) & 0xff; + bp_commbuf[i++] = readcnt & 0xff; + memcpy(bp_commbuf + i, writearr, writecnt); + + ret = buspirate_sendrecv(bp_commbuf, i + writecnt, 1 + readcnt); + + if (ret) { + msg_perr("Bus Pirate communication error!\n"); + return SPI_GENERIC_ERROR; + } + + if (bp_commbuf[0] != 0x01) { + msg_perr("Protocol error while sending SPI write/read!\n"); + return SPI_GENERIC_ERROR; + } + + /* Skip Ack. */ + memcpy(readarr, bp_commbuf + 1, readcnt); + + return ret; +}

1 0

Add a "device" parameter for Dediprog
by David Hendricks 01 Nov '12

01 Nov '12

This patch adds a "device" parameter for Dediprog which enables use of multiple dediprogs connected to a single machine. Very handy for test racks. Example usage: flashrom -p dediprog:device=0 flashrom -p dediprog:device=1 etc... The patch was originally written by Nathan Laredo, I'm just forwarding it upstream: Signed-off-by: Nathan Laredo <nil(a)google.com> Signed-off-by: David Hendricks <dhendrix(a)google.com> Index: dediprog.c =================================================================== --- dediprog.c (revision 1620) +++ dediprog.c (working copy) @@ -46,7 +46,9 @@ #endif /* Might be useful for other USB devices as well. static for now. */ -static struct usb_device *get_device_by_vid_pid(uint16_t vid, uint16_t pid) +/* device parameter allows user to specify one device of multiple installed */ +static struct usb_device *get_device_by_vid_pid(uint16_t vid, uint16_t pid, + int device) { struct usb_bus *bus; struct usb_device *dev; @@ -54,8 +56,11 @@ for (bus = usb_get_busses(); bus; bus = bus->next) for (dev = bus->devices; dev; dev = dev->next) if ((dev->descriptor.idVendor == vid) && - (dev->descriptor.idProduct == pid)) - return dev; + (dev->descriptor.idProduct == pid)) { + if (device == 0) + return dev; + device--; + } return NULL; } @@ -777,8 +782,9 @@ int dediprog_init(void) { struct usb_device *dev; - char *voltage; + char *voltage, *device; int millivolt = 3500; + int usedevice = 0; int ret; msg_pspew("%s\n", __func__); @@ -792,11 +798,21 @@ msg_pinfo("Setting voltage to %i mV\n", millivolt); } + device = extract_programmer_param("device"); + if (device) { + usedevice = strtol(device, NULL, 0); + free(device); + if (usedevice < 0) + return 1; + msg_pinfo("Using device %i\n", usedevice); + } + + /* Here comes the USB stuff. */ usb_init(); usb_find_busses(); usb_find_devices(); - dev = get_device_by_vid_pid(0x0483, 0xdada); + dev = get_device_by_vid_pid(0x0483, 0xdada, usedevice); if (!dev) { msg_perr("Could not find a Dediprog SF100 on USB!\n"); return 1; -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc.

1 0

Re: [flashrom] laptop with no BIOS? or BIOS reflash pain
by Anton Shterenlikht 01 Nov '12

01 Nov '12

Date: Tue, 30 Oct 2012 21:28:22 +0100 Subject: Re: laptop with no BIOS? or BIOS reflash pain From: Idwer Vollering <vidwer(a)gmail.com> To: freebsd-questions(a)freebsd.org, flashrom(a)flashrom.org Another approach is to use an external SPI programmer: http://flashrom.org/Supported_programmers The 'downside' of this is that you need to take your laptop apart. ODM schematics of your laptop are found here: http://notebookschematic.com/wp-content/uploads/2010/06/6515b_6715s.png Downloads for BIOS updates: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&… and ftp://ftp.hp.com/pub/softpaq/sp55501-56000/sp55556.exe My guess (I am not a HP service technician) is that you need ROM.CAB/Rom.bin from sp55556.exe - you can use 7zip to extract Rom.bin This is probably way beyond my skills, but thanks anyway. Anton

1 0

Re: [flashrom] Reading EPROM on RTL8139
by Stefan Tauner 01 Nov '12

01 Nov '12

On Wed, 31 Oct 2012 20:58:36 +0300 Dmitry the Zuryanovich <dreadbit(a)gmail.com> wrote: > I'm tryng to read some old UV-erased 28 pin 27xx hi! which one? is it known to work with flashrom? please also include a verbose log (i.e. add -V to the command line). -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

ASRock ALiveNF6G-GLAN: flashrom -V
by Samuel Hildebrandt 31 Oct '12

31 Oct '12

Sorry for my first message, I had not upgraded to the latest version of flashprog before sending it ... Samuel $ sudo flashrom -V -p internal flashrom v0.9.6.1-runknown on Linux 3.2.0-32-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.8, GCC 4.6.3, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 899M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1000 us, 10000 myus = 10015 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: "ASRock" DMI string baseboard-product-name: "ALiveNF6G-GLAN" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found Winbond Super I/O, id 0x88 Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0x00000000 MCP SPI is not used. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. The following protocols are supported: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x73, id2 0x63, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0x50 Found Winbond flash chip "W39V040C" (512 kB, LPC) at physical address 0xfff80000. Lockout bits: Hardware bootblock locking (#TBL) is not active. Hardware remaining chip locking (#WP) is not active.. Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0x50 Found Winbond flash chip "W39V040C" (512 kB, LPC). No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88

2 1

Reading EPROM on RTL8139
by Dmitry the Zuryanovich 31 Oct '12

31 Oct '12

Hi All, I'm tryng to read some old UV-erased 28 pin 27xx on some Compex RTL-8139 card with 28 pin socket (32 pin socket may be soldered there, but it is not!) (I have 2 installed, the PCI address is correct) on Linux-Slackware-14 as root with the following: flashrom --programmer nicrealtek:pci=00:09.0 -f -r bios Calibrating delay loop... delay loop is unreliable, trying to continue OK. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. Am I doing things right or that's may be just a broken EPROM? -- -- jabber: dreadbit(a)jabber.ru /compatible with Google chat, yandex chat and other modern shit/

1 0

W836xx:NI 8351 (rebranded MSI MS-9218) flashrom -V
by Miklos Marton 31 Oct '12

31 Oct '12

Hello, See below the output of the /flashrom -p internal -V on a National Instruments 8351 Rackmount Controller. It is a rebranded MSI MS-9218. After specifying the laptop:this_is_not_a_laptop option the flashrom is able to detect and read the flash fine: Proceeding anyway because user forced us to. Found chipset "Intel ICH7/ICH7R". Enabling flash write... OK. Found SST flash chip "SST49LF008A" (1024 kB, FWH) at physical address 0xfff00000. Reading flash... done. root@TS333:~/flashrom# ./flashrom -p internal -V flashrom v0.9.6.1-r1620 on Linux 2.6.32-41-generic-pae (i686) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.0.0, GCC 4.4.3, little endian Command line (3 args): ./flashrom -p internal -V Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MSI" DMI string system-product-name: "GrantsDale CRB Board" DMI string system-version: "MSI CORPORATION" DMI string baseboard-manufacturer: "bbl" DMI string baseboard-product-name: "MS-9218" DMI string baseboard-version: "Revision A " DMI string chassis-type: "Other" DMI chassis-type is not specific enough. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: e9. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. ======================================================================== WARNING! You may be running flashrom on an unsupported laptop. We could not detect this for sure because your vendor has not setup the SMBIOS tables correctly. You can enforce execution by adding '-p internal:laptop=this_is_not_a_laptop' to the command line, but please read the following warning if you are not sure. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. Error: Programmer initialization failed. Please see below the output of the dmidecode: SMBIOS 2.33 present. 33 structures occupying 1025 bytes. Table at 0x000DC010. Handle 0x0000, DMI type 0, 20 bytes BIOS Information Vendor: MSI Version: P9218NI V1.36 Release Date: 10/26/2006 Address: 0xE4F80 Runtime Size: 110720 bytes ROM Size: 1024 kB Characteristics: ISA is supported PCI is supported PC Card (PCMCIA) is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available USB legacy is supported Smart battery is supported BIOS boot specification is supported Handle 0x0001, DMI type 1, 25 bytes System Information Manufacturer: MSI Product Name: GrantsDale CRB Board Version: MSI CORPORATION Serial Number: 0123456789 UUID: Not Settable Wake-up Type: Power Switch Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: bbl Product Name: MS-9218 Version: Revision A Serial Number: 400 Handle 0x0003, DMI type 3, 17 bytes Chassis Information Manufacturer: MSI Type: Other Lock: Not Present Version: N/A Serial Number: None Asset Tag: No Asset Tag Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00001234 Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: LGA775/PRESCOTT Type: Central Processor Family: Pentium 4 Manufacturer: Intel Corporation ID: 44 0F 00 00 FF FB EB BF Signature: Type 0, Family 15, Model 4, Stepping 4 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) PAE (Physical address extension) MCE (Machine check exception) CX8 (CMPXCHG8 instruction supported) APIC (On-chip APIC hardware supported) SEP (Fast system call) MTRR (Memory type range registers) PGE (Page global enable) MCA (Machine check architecture) CMOV (Conditional move instruction supported) PAT (Page attribute table) PSE-36 (36-bit page size extension) CLFSH (CLFLUSH instruction supported) DS (Debug store) ACPI (ACPI supported) MMX (MMX technology supported) FXSR (Fast floating-point save and restore) SSE (Streaming SIMD extensions) SSE2 (Streaming SIMD extensions 2) SS (Self-snoop) HTT (Hyper-threading technology) TM (Thermal monitor supported) PBE (Pending break enabled) Version: Intel(R) Pentium(R) D CPU 3.00GHz Voltage: 1.8 V External Clock: Unknown Max Speed: 3800 MHz Current Speed: 3000 MHz Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: Not Provided Serial Number: <BAD INDEX> Asset Tag: <BAD INDEX> Part Number: <BAD INDEX> Invalid entry length (0). DMI table is broken! Stop. Our company is manufacturing a wide range of embedded x86 based PXI controllers. I have checked some, and most of them was worked with the flashrom after specifying the this_is_not_a_laptop switch. What kind of information do you need to get them officaly verified and supported? Thank you for the flashrom, this is a great program! Regards, Miklós Márton | Test Engineer / NIH Test Development | Tel: +36-30-521-1052 | NI Hungary Kft NI Hungary Kft. H-4031 Debrecen Határ u 1/A. Telefon: +36 (52) 515 400 Cégjegyzékszám: 09-09-009315 Bejegyezte: Debreceni Törvényszék Cégbírósága

2 3

BIOS reflash to add boot from USB
by Fbsd8 31 Oct '12

31 Oct '12

I have a dell dimension 3000 that lacks the ability to boot from USB. Does flashrom have way to add this option?

2 1

Re: [flashrom] flashing MX25L3205DM2I-12G
by Stefan Tauner 31 Oct '12

31 Oct '12

On Wed, 31 Oct 2012 09:40:02 -0400 "Pupic P." <ladypupic(a)gmail.com> wrote: > Hi everyone, > > I have a MacBook Pro (13" mid-2009) who, I think, suffers from a bad > firmware flash : from nowhere, or after an update, it makes 9 beeps when > powered on (3 short, 3 long, 3 short) and nothing else. I have found > references from similar cases when people seemed to have recovered by > rewriting a good firmware with flashrom and buspirate ( > http://ho.ax/tag/firmware/). > On my machine I have : > - a chip labelled MX25L3205DM2I-12G > - buspirate 3.6 (v3b, firmware 5.10) > - flashrom v0.9.6.1-r1620 > - hooked (while the chip still on the motherboard (no power, battery out)) > : pin1->CS, pin2->MISO, pin4->GND, pin5->MOSI, pin6->CLK, pin8->3.3v > > * Pins 3,7 not connected. > * I also tried pins 3,7,8 together with the same result. they need to be connected, in this case they need to be set to a distinct potential (namely vcc), but you should always connect all pins of an IC unless noted otherwise in its datasheet. floating pins are evil. > What I get is flashrom ending with : > Probing for Generic unknown SPI chip (RDID), 0 kB: RDID byte 0 parity > violation. probe_spi_rdid_generic: id1 0x00, id2 0x00 > Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI) on > buspirate_spi. > Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0x0, > id2 0x0 > Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI). > > Any idea why? this means that MISO is always read as low. this can have a number of reasons. one of example is that pin8 is also connected to a number of other components that need more power than the bus pirate (or whatever) can deliver. see also http://flashrom.org/ISP -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

flashing MX25L3205DM2I-12G
by Pupic P. 31 Oct '12

31 Oct '12

Hi everyone, I have a MacBook Pro (13" mid-2009) who, I think, suffers from a bad firmware flash : from nowhere, or after an update, it makes 9 beeps when powered on (3 short, 3 long, 3 short) and nothing else. I have found references from similar cases when people seemed to have recovered by rewriting a good firmware with flashrom and buspirate ( http://ho.ax/tag/firmware/). On my machine I have : - a chip labelled MX25L3205DM2I-12G - buspirate 3.6 (v3b, firmware 5.10) - flashrom v0.9.6.1-r1620 - hooked (while the chip still on the motherboard (no power, battery out)) : pin1->CS, pin2->MISO, pin4->GND, pin5->MOSI, pin6->CLK, pin8->3.3v * Pins 3,7 not connected. * I also tried pins 3,7,8 together with the same result. What I get is flashrom ending with : Probing for Generic unknown SPI chip (RDID), 0 kB: RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x00 Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI) on buspirate_spi. Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0x0, id2 0x0 Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI). Any idea why? Thanks. Mario.

1 0

Flashrom 9.3 erarse and write error
by pradeep.p581＠wipro.com 31 Oct '12

31 Oct '12

Hi, We are using BIOS+ME region with the help of vendor tool. >From Flashrom tool, we are looking for Save/Update the NVRAM BIOS setting region. We are able to read the NVRAM BIOS setting, but we are not able to write NVRAM setting as flashrom is not allowing us to write on to bios region. Because erase is not happening before writing and also spi_send_multicommand() in flashrom is failing. If it is possible could you please help us to provide the command for erasing and writing on to NVRAM BIOS setting? Thanks & Regards Pradeep p Please do not print this email unless it is absolutely necessary. The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. www.wipro.com

2 5

Re: [flashrom] laptop with no BIOS? or BIOS reflash pain
by Idwer Vollering 30 Oct '12

30 Oct '12

> I've HP compaq 6715s laptop. > It's all right with 10-current. > I've got wireless and at one point > I even managed to get flash working. > > My problem is with BIOS. > Apparently it's wrong and John Baldwin > provided me with a pci.c patch to get > it to boot. > > There is an updated BIOS version, but > so far I failed to get it installed. > HP only provide MS and freedos executables. > I tried BartPE - doesn't work. > I tried plugging in a MS disk - doesn't work. > The only think I haven't tried is getting > a spare disk, installing freedos on it > and then running the freedos executable > from USB - what a fucking pain... > > For proper hardware (servers) HP provide > images which are executed from management > console, but not for laptops. > I guess the idea that one might > use their laptops for anything other than MS > is so wild, that it never crossed their maid. > > Anyway, I think I've heard there are some laptops > with no BIOS, is this true? > Or perhaps there are brands where BIOS > reflash is not such a great pain? > I remember on Compaq Armada the BIOS was > stored on disk and Compaq provided a floppy > image to boot from and reflash BIOS. > That was easy. > Anything like this exist these days? > Are there any EFI laptops? > Any model people would recommend? > > Thanks > > Anton Another approach is to use an external SPI programmer: http://flashrom.org/Supported_programmers The 'downside' of this is that you need to take your laptop apart. ODM schematics of your laptop are found here: http://notebookschematic.com/wp-content/uploads/2010/06/6515b_6715s.png Downloads for BIOS updates: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&… and ftp://ftp.hp.com/pub/softpaq/sp55501-56000/sp55556.exe My guess (I am not a HP service technician) is that you need ROM.CAB/Rom.bin from sp55556.exe - you can use 7zip to extract Rom.bin

1 0

[PATCH] Add board enable for Asus DSAN-DX.
by Stefan Tauner 29 Oct '12

29 Oct '12

IDs are from the host bridge and LPC controller. The enable function was reverse engineered by roxfan, thanks! Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- Hello mezzo, we have hopefully figured out how the write protection can be disabled. you need to apply the following patch to the source code of flashrom and recompile it. see http://flashrom.org/Download#Installation_from_source for details... when you have recompiled it successfully, please send us the output of flashrom -p internal -V and retry writing, thanks. diff --git a/board_enable.c b/board_enable.c index 8f0219e..cfba5b9 100644 --- a/board_enable.c +++ b/board_enable.c @@ -1823,6 +1823,7 @@ static int intel_ich_gpio26_raise(void) /* * Suited for: + * - ASUS DSAN-DX * - P4SD-LA (HP OEM): i865 + ICH5 * - GIGABYTE GA-8IP775: 865P + ICH5 * - GIGABYTE GA-8PE667 Ultra 2: socket 478 + i845PE + ICH4 @@ -2335,6 +2336,7 @@ const struct board_match board_matches[] = { {0x10DE, 0x0260, 0x103C, 0x2A34, 0x10DE, 0x0264, 0x103C, 0x2A34, "NODUSM3", NULL, NULL, P3, "ASUS", "A8M2N-LA (NodusM3-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, {0x10DE, 0x0260, 0x103c, 0x2a3e, 0x10DE, 0x0264, 0x103c, 0x2a3e, "NAGAMI2L", NULL, NULL, P3, "ASUS", "A8N-LA (Nagami-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, {0x10de, 0x0264, 0x1043, 0x81bc, 0x10de, 0x02f0, 0x1043, 0x81cd, NULL, NULL, NULL, P3, "ASUS", "A8N-VM CSM", 0, OK, w83627ehf_gpio22_raise_2e}, + {0x8086, 0x65c0, 0x1043, 0x8301, 0x8086, 0x2916, 0x1043, 0x82a6, "^DSAN-DX$", NULL, NULL, P3, "ASUS", "DSAN-DX", 0, OK, intel_ich_gpio32_raise}, {0x10DE, 0x0264, 0x1043, 0x81C0, 0x10DE, 0x0260, 0x1043, 0x81C0, NULL, NULL, NULL, P3, "ASUS", "M2NBP-VM CSM", 0, OK, nvidia_mcp_gpio0_raise}, {0x1106, 0x1336, 0x1043, 0x80ed, 0x1106, 0x3288, 0x1043, 0x8249, NULL, NULL, NULL, P3, "ASUS", "M2V-MX", 0, OK, via_vt823x_gpio5_raise}, {0x8086, 0x24cc, 0, 0, 0x8086, 0x24c3, 0x1043, 0x1869, "^M6Ne$", NULL, NULL, P3, "ASUS", "M6Ne", 0, NT, intel_ich_gpio43_raise}, diff --git a/print.c b/print.c index 5a27320..2092b5a 100644 --- a/print.c +++ b/print.c @@ -634,6 +634,7 @@ const struct board_info boards_known[] = { B("ASUS", "A8V-E SE", OK, "http://www.asus.com/Motherboards/AMD_Socket_939/A8VE_SE/", "See http://www.coreboot.org/pipermail/coreboot/2007-October/026496.html"), B("ASUS", "Crosshair II Formula", OK, "http://www.asus.com/Motherboards/AMD_AM2Plus/Crosshair_II_Formula/", NULL), B("ASUS", "Crosshair IV Extreme", OK, "http://www.asus.com/Motherboards/AMD_AM3/Crosshair_IV_Extreme/", NULL), + B("ASUS", "DSAN-DX", OK, "http://www.asus.com/Server_Workstation/Server_Motherboards/DSANDX/", NULL), B("ASUS", "E35M1-I DELUXE", OK, "http://www.asus.com/Motherboards/AMD_CPU_on_Board/E35M1I_DELUXE/", NULL), B("ASUS", "K8N", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8N/", NULL), B("ASUS", "K8V", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8V/", NULL), -- Kind regards, Stefan Tauner

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom