- flashrom - mail.coreboot.org

Re: [flashrom] [PATCH] 4 byte address mode for Macronix MX25L25735F
by Tim Chick 05 Apr '16

05 Apr '16

Hi David, There was a mistake in the logic, which I have corrected. I was also asked by someone else on the list if it worked with the MX25L25635F, which is 32Mbytes, but uses 3-byte addressing by default. So I made the attached changes, which switch the chip to 4-byte mode. It also has some dedicated 4-byte commands, and a BAR register, but it seemed easiest to just use what I had tested for the MX25L25735F. I can’t actually test the MX25L25635F though, as I don’t have one. Thanks, Tim From: David Hendricks [mailto:dhendrix@google.com] Sent: 04 April 2016 23:21 To: Tim Chick Cc: flashrom(a)flashrom.org Subject: Re: [flashrom] [PATCH] 4 byte address mode for Macronix MX25L25735F On Thu, Mar 31, 2016 at 8:21 AM, Tim Chick <Tim.Chick(a)mediatek.com<mailto:Tim.Chick@mediatek.com>> wrote: Hi List, Flashrom would not detect this chip. When the definition was added, everything failed as the chip only supports 4 byte address operation. Interesting - I didn't know such chips existed. The ones I've used have backwards-compatible commands that support 3-byte addresses. FYI - Some other high-capacity chips have 4-byte address enable bit in a config register that will make the usual read/write/erase instructions accept 4 byte addresses. And yet other large chips have alternative instructions that function the same but only accept a 4-byte address. The attached patch adds 4 byte address support for 4 byte only chips, as determined by the JEDEC flash parameter table, and support for this chip specifically. I’ve only allowed it to work with the SPI_CONTROLLER_FT2232 controller, as that is the only one I have to test. I’ve also only ported spi_block_erase_20 – the other block erase functions will fail. Please let me know what you think! Good stuff! FWIW, I have a work-in-progress patch on chromium.org<http://chromium.org> (https://chromium-review.googlesource.com/#/c/323359/) for the other types of high-capacity flash chips. I've tested on a Spansion S25FS256 using linux_spi and ft2232. It needs a lot of clean-up, but might be of help. Most of the changes were to convert read/write/erase functions to use allocated buffers whose length depends on whether we're using a 3- or 4-byte address. I'll borrow some ideas from your patch as well to support the "4-byte address only" chips. -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc.

2 1

[PATCH] 4 byte address mode for Macronix MX25L25735F
by Tim Chick 05 Apr '16

05 Apr '16

Hi List, Flashrom would not detect this chip. When the definition was added, everything failed as the chip only supports 4 byte address operation. The attached patch adds 4 byte address support for 4 byte only chips, as determined by the JEDEC flash parameter table, and support for this chip specifically. I've only allowed it to work with the SPI_CONTROLLER_FT2232 controller, as that is the only one I have to test. I've also only ported spi_block_erase_20 - the other block erase functions will fail. Please let me know what you think! Thanks, Tim

2 1

[PATCH] Add support for GD25Q21B, GD25Q41B, GD25Q80C and GD25Q16C
by Hatim Kanchwala 04 Apr '16

04 Apr '16

Hello, This patch supersedes the corresponding one I sent earlier as part of a chain (http://patchwork.coreboot.org/patch/4420). Stefan's suggestions on previous patches (discussed on list and IRC) are incorporated. The new definitions are combined with their counterparts. Thanks. :) Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> --- flashchips.c | 28 ++++++++++++++++------------ flashchips.h | 4 ++-- 2 files changed, 18 insertions(+), 14 deletions(-) diff --git a/flashchips.c b/flashchips.c index 40b6b8e..7947256 100644 --- a/flashchips.c +++ b/flashchips.c @@ -5933,37 +5933,38 @@ const struct flashchip flashchips[] = { .block_erase = spi_block_erase_60, }, { .eraseblocks = { {128 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", - .name = "GD25Q20(B)", + .name = "GD25Q20(B)/GD25Q21B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q20, .total_size = 256, .page_size = 256, - .feature_bits = FEATURE_WRSR_WREN, + /* OTP (GD25Q21B only): 1536B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 64} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 8} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 4} }, .block_erase = spi_block_erase_d8, }, { @@ -5971,76 +5972,78 @@ const struct flashchip flashchips[] = { .block_erase = spi_block_erase_60, }, { .eraseblocks = { {256 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", - .name = "GD25Q40(B)", + .name = "GD25Q40(B)/GD25Q41B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q40, .total_size = 512, .page_size = 256, - .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_UNTESTED, + /* OTP (GD25Q41B only): 1536B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 128} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 16} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 8} }, .block_erase = spi_block_erase_d8, }, { .eraseblocks = { {512 * 1024, 1} }, .block_erase = spi_block_erase_60, }, { .eraseblocks = { {512 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", - .name = "GD25Q80(B)", + .name = "GD25Q80(B)(C)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q80, .total_size = 1024, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */ - .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 (B and C revisions only) */ + /* supports SFDP (C revision only) */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 256} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 32} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 16} }, .block_erase = spi_block_erase_d8, }, { @@ -6048,38 +6051,39 @@ const struct flashchip flashchips[] = { .block_erase = spi_block_erase_60, }, { .eraseblocks = { {1024 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", - .name = "GD25Q16(B)", + .name = "GD25Q16(B)(C)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q16, - .total_size = 2048, + .total_size = 2* 1024, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */ - .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 (B and C revisions only) */ + /* supports SFDP (C revision only) */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 512} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 64} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 32} }, .block_erase = spi_block_erase_d8, }, { diff --git a/flashchips.h b/flashchips.h index 9ffb30f..997b3cb 100644 --- a/flashchips.h +++ b/flashchips.h @@ -353,32 +353,32 @@ #define FUJITSU_MBM29LV008TA 0x3E #define FUJITSU_MBM29LV080A 0x38 #define FUJITSU_MBM29LV200BC 0xBF #define FUJITSU_MBM29LV200TC 0x3B #define FUJITSU_MBM29LV400BC 0xBA #define FUJITSU_MBM29LV400TC 0xB9 #define FUJITSU_MBM29LV800BA 0x5B /* Same as MBM29LV800BE */ #define FUJITSU_MBM29LV800TA 0xDA /* Same as MBM29LV800TE */ #define FUJITSU_MBM29LV160BE 0x49 /* 16 b mode 0x2249 */ #define FUJITSU_MBM29LV160TE 0xC4 /* 16 b mode 0x22C4 */ #define GIGADEVICE_ID 0xC8 /* GigaDevice */ #define GIGADEVICE_GD25T80 0x3114 #define GIGADEVICE_GD25Q512 0x4010 #define GIGADEVICE_GD25Q10 0x4011 -#define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25QB */ -#define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25QB */ +#define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25Q21B which supports OTP */ +#define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25Q41B which supports OTP */ #define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */ #define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */ #define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ #define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ #define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B and GD25Q128C only, can be distinguished by SFDP */ #define GIGADEVICE_GD25VQ21B 0x4212 #define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ #define GIGADEVICE_GD25VQ80C 0x4214 #define GIGADEVICE_GD25VQ16C 0x4215 #define GIGADEVICE_GD25LQ40 0x6013 #define GIGADEVICE_GD25LQ80 0x6014 #define GIGADEVICE_GD25LQ16 0x6015 #define GIGADEVICE_GD25LQ32 0x6016 #define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */ #define GIGADEVICE_GD25LQ128 0x6018 -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 1

Programming N25Q128
by Steve Miller 01 Apr '16

01 Apr '16

FYI, This is informational only. I can program the ROM. When programming the N25Q128 from the Raspberry PI, I will get verification errors. If I push it up the hill several times, it will eventually pass. The N25Q128 remains on the target board, I am hold the ARM processor on that board in RESET. The Raspberry PI is attached via a ribbon cable and 100 ohm series resistors. Since my system is unique, it is entirely possible that this is just an artifact of my setup. However, the message as pasted below, asked me to report it, so I am doing that. I tried both the release and the latest snapshot. Both seem to operate the same. I tried three different target boards with the N25Q128 and all operate the same. Verification fails, but if I repeat the programming operation several times, it will pass. Please note the message at the end. The previous program and verify attempt failed. However, when I tried again, it aborted early because what I was attempting to program into the part already matched the parts contents. AKA, nothing to do. ---- Steve ************************************************************************************************************* Verifying flash... FAILED at 0x00022f00! Expected=0x61, Found=0xff, failed byte count from 0x00000000-0x00ffffff: 0x100 Your flash chip is in an unknown state. Please report this on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org, thanks! Verifying flash... FAILED at 0x0001cc92! Expected=0x83, Found=0x9f, failed byte count from 0x00000000-0x00ffffff: 0x68 Your flash chip is in an unknown state. Please report this on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org, thanks! Warning: Chip content is identical to the requested image. Erase/write done.

1 0

Re: [flashrom] Programming N25Q256 ?
by Steve Miller 01 Apr '16

01 Apr '16

Thanks David for the very quick feedback. For others that might see a similar symptom of MISO not toggling, here is what I did wrong. This part is a QSPI. It can work in a number of modes, for single bit SPI, up through four bit SPI. On the board, there were some missing pullup resistors. MISO, #HOLD, and #WP did not have pullups. When I added 4.7K ohm pullups to those three pins, the MISO started toggling and flashrom reported that “This flash part has status NOT WORKING for operations: PROBE READ ERASE WRITE “ This is to be expected, as the N25Q256 is not supported. On this Micron part, the #HOLD, and #WIP pins are dual function. In four bit mode, they are data bits. Therefore, the need for pullups is not obvious. However, until I added them, the part was dead as a mackerel. I could not find the Chromium branch, so I could not try that version. I did try the latest release candidate, but it operated the same. However, we don’t really need that large a PROM, so we have N25Q128 chips on order for delivery tomorrow. I believe that one is supported, so we should be able to program after swapping the chip. From: David Hendricks [mailto:dhendrix@google.com] Sent: Wednesday, March 30, 2016 06:11 PM To: Steve Miller Cc: flashrom(a)flashrom.org Subject: Re: [flashrom] Programming N25Q256 ? On Wed, Mar 30, 2016 at 3:14 PM, Steve Miller <stevem(a)tanisys.com<mailto:stevem@tanisys.com>> wrote: Hi, I have the code built and running on a Raspberry PI. Unfortunately, the target part I am trying to program is a Micron N25Q256. I don’t see that part in the list. When I execute the program with –VV it seems to scan lots of devices. I see activity on CLK, CS, MOSI with an oscilloscope. But MISO remains logic low. When the program terminates, it just tells me No EEPROM/Flash device found. Stupid Noob Questions: 1. Is the static level on MISO to be expected? Or should it at least toggle? You should definitely see some activity on MISO. Flashrom sends identification instructions (RDID, REMS, etc) to the chip and the chip should respond with its JEDEC-assigned manufacturer ID and vendor-specific device info. That said, the N25Q256 is not currently added in upstream flashrom. There is limited support in the Chromium branch, though. 2. Is there any hope with this device? Can I perhaps force it to think the chip is smaller? Yep, that's what we currently do in the Chromium branch*. The chip uses 24-bit addresses unless either a bit in a nonvolatile config register is set or alternate instructions which accept 32-bit addresses are used. *Full 4-byte address support should be ready soon, I just need to find a few spare cycles to finish up what I have written... -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc.

1 0

Programming N25Q256 ?
by Steve Miller 31 Mar '16

31 Mar '16

Hi, I have the code built and running on a Raspberry PI. Unfortunately, the target part I am trying to program is a Micron N25Q256. I don't see that part in the list. When I execute the program with -VV it seems to scan lots of devices. I see activity on CLK, CS, MOSI with an oscilloscope. But MISO remains logic low. When the program terminates, it just tells me No EEPROM/Flash device found. Stupid Noob Questions: 1. Is the static level on MISO to be expected? Or should it at least toggle? 2. Is there any hope with this device? Can I perhaps force it to think the chip is smaller? Thanks for any help or suggestions. ----- Steve P.S. This device is not on a production Motherboard. It is on an ARM processor board that we are developing. The board is a new design that will not boot. I am attempting to program this SPI EEPROM to at least get into a UBOOT environment.

2 1

Re: [flashrom] [2/2] Add support for GD25D05B and GD25D10B
by sean boree 30 Mar '16

30 Mar '16

Hello Hatim, I have checked your patch; I only have one small remark (and I might be very wrong on this, but I felt it best to discuss). 1 You use spi_prettyprint_status_register_bp2_srwd for both devices, however this function also prints the bits 5, 6 (with spi_prettyprint_status_register_bit). The datasheets of GD25D05B and GD25D10B note that these bits are reserved. So I think either they should not be used (thus different print function) or it should be noted somewhere that these are reserved bits. Acked-by: Sean Boree <seanboree(a)gmail.com> > Hatim Kanchwala <hatim(a)hatimak.me> - 2016-03-16 15:39:23 > Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me>

1 0

Re: [flashrom] [PATCH] adding support for AT25DQ321
by Hatim Kanchwala 27 Mar '16

27 Mar '16

Dear Sean, Thanks for your patch. Here's a few issues I found - 1. For patches that touch struct flashchip it is wise to include more context lines. Have a look here (https://www.flashrom.org/Development_Guidelines#Patch_submission). 2. Tabs were converted to spaces. You can have a look at the AT25F512 entry just below it to understand the differences. 3. Regarding total_size, we write it usually as "x * 1024" that is to be read as "x kB". 4. This particular chip supports dual and quad I/O, so the FEATURE_QPI bit should be set and you can also include a comment. Just have a look at other entries in flashchips.c. 5. IMHO, the FIXME comment in spi25_statusreg.c should only come at spi_prettyprint_status_register_at25df_sec and not spi_prettyprint_status_register_at25df, because AT25DQ321 really uses only the former. Apart from the above, the content looks fine to me. Thanks for the patch. :) Acked-by: Hatim Kanchwala <hatim(a)hatimak.me> On Sunday 27 March 2016 05:15 AM, sean boree wrote: > This patch adds support for the AT25DQ321 chip, as this is my first patch, I apologise > for any rookie mistakes I made. > > > Signed-off-by: Sean Boree <seanboree(a)gmail.com <mailto:seanboree@gmail.com>> > > > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > https://www.flashrom.org/mailman/listinfo/flashrom > -- Kind Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 0

[PATCH] adding support for AT25DQ321
by sean boree 27 Mar '16

27 Mar '16

This patch adds support for the AT25DQ321 chip, as this is my first patch, I apologise for any rookie mistakes I made. Signed-off-by: Sean Boree <seanboree(a)gmail.com>

1 0

W836xx: Flex 3-1570: flashrom -V
by Laptander developer 26 Mar '16

26 Mar '16

Hello, flashrom asked me to send output of flashrom -V here. sudo flashrom -p internal -V ------- Start of output ------- flashrom v0.9.6.1-r1563 on Linux 3.16.0-38-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (3 args): flashrom -p internal -V Calibrating delay loop... OS timer resolution is 1 usecs, 2887M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 997 us, 10000 myus = 9998 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "LENOVO" DMI string system-product-name: "80JM" DMI string system-version: "Flex 3-1570" DMI string baseboard-manufacturer: "LENOVO" DMI string baseboard-product-name: "Flex 3-1570" DMI string baseboard-version: "31900058 WIN" DMI string chassis-type: "Notebook" Laptop detected via DMI. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: fc. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. ======================================================================== WARNING! You seem to be running flashrom on an unsupported laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. Error: Programmer initialization failed. -------- End of output ------- I have read warning about using flashrom on laptops. So I made a full backup of bios by fpt on freedos. By the way, why my chipname (N25Q064) is marked as supported in hardware list? Also, is it possible to place my serial info into cap file from vendor?

1 0

Re: [flashrom] Dediprogress (was: Re: dediprog: Use command 0x0B only on older SF100s)
by Stefan Tauner 25 Mar '16

25 Mar '16

On Sat, 15 Aug 2015 19:42:58 -0700 David Hendricks <david.hendricks(a)gmail.com> wrote: > (I figured we could use a new thread to track overall progress) > > A few more tweaks and now writes work, too: > https://chromium-review.googlesource.com/#/c/293889 FWIW, I have merged my refined version of Dediprog SF100 supporting the new protocol. It also enables compilation of the Dediprog programmer by default (finally). -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

[GSoC 2016] Obscure Features, Locking/Unlocking of Access Protection and CFI
by Hatim Kanchwala 25 Mar '16

25 Mar '16

Hello, I have applied for GSoC 2016 with flashrom. Here's the link to my proposal - https://goo.gl/Iswzlv. Please have a look. I am wondering whether to include any stretch goals. Following are the ideas (as discussed over IRC) - * libflashrom - review and improve pending patches from Nico and Lukasz * Frequencies - store maximum frequency for chip - possible leads to faster reads * Multi I/O SPI - but, first look at pending patches - not many programmers will be useful I have less than 20 hours before deadline, so I would appreciate quick responses. Personally, GSoC is important for me so any feedback or comment you have to offer will be valuable. Thank you for your time. :) -- Kind Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 0

Intel QS77 / Eon EN25QH64 - read failed
by Artur Szymanski 24 Mar '16

24 Mar '16

flashrom v0.9.9-r1955 on FreeBSD 10.2-RELEASE-p9 (amd64) flashrom is free software, get the source code at https://flashrom.org flashrom was built with libpci 3.4.1, LLVM Clang 3.4.1 (tags/RELEASE_34/dot1-final 208032), little endian Command line (5 args): flashrom -VVV -p internal -r /tmp/intelbios Calibrating delay loop... OS timer resolution is 1 usecs, 897M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1002 us, 10000 myus = 10003 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. page_size=1000 pre-rounding: start=0x00000000000f0000, len=0x10000, end=0x0000000000100000 post-rounding: start=0x00000000000f0000, len=0x10000, end=0x0000000000100000 No DMI table found. page_size=1000 pre-rounding: start=0x00000008007c4000, len=0x10000, end=0x00000008007d4000 post-rounding: start=0x00000008007c4000, len=0x10000, end=0x00000008007d4000 Found chipset "Intel QS77" with PCI ID 8086:1e56. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 page_size=1000 pre-rounding: start=0x00000000fed1c000, len=0x4000, end=0x00000000fed20000 post-rounding: start=0x00000000fed1c000, len=0x4000, end=0x00000000fed20000 GCS = 0xc41: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: not enabled 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI Read Configuration: prefetching enabled, caching enabled, BIOS_CNTL = 0x2b: BIOS Lock Enable: enabled, BIOS Write Enable: enabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2b. SPIBAR = 0x00000008007c4000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0x20, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x9f, read w/o addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x00, read w/o addr, none op[7]: 0x00, read w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x00 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00003000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x07ff01c0 FREG1: BIOS region (0x001c0000-0x007fffff) is read-write. 0x5C: 0x01bf0003 FREG2: Warning: Management Engine region (0x00003000-0x001bffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00001fff FREG4: Platform Data region is unused. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see https://flashrom.org/ME for details. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0xc4 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf90000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=1 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040003 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x49900024 FLILL 0x00000000 --- Details --- Component 1 density: 8 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz Dual Output Fast Read Support: disabled No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x07ff01c0 FLREG2 0x01bf0003 FLREG3 0x00020001 FLREG4 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x001c0000 - 0x007fffff Region 2 (ME ) 0x00003000 - 0x001bffff Region 3 (GbE ) 0x00001000 - 0x00002fff Region 4 (Platf.) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw checking for opcode 0x03 checking for opcode 0x05 OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L05PT from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L05PU, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L05PU from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L10PT, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L10PT from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L10PU, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L10PU from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L20PT, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L20PT from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L20PU, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L20PU from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L40PT, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L40PT from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L40PU, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L40PU from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L80P, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L80P from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for AMIC A25L16PT, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L16PT from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for AMIC A25L16PU, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L16PU from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for AMIC A25L512, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L512 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L010, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L010 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L020, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L020 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L040 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for AMIC A25L080, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L080 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for AMIC A25L016, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L016 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for AMIC A25L032, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping A25L032 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for AMIC A25LQ16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping A25LQ16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping A25LQ032/A25LQ32A from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for AMIC A25LQ64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping A25LQ64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT25DF021, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF021 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25DF041A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF041A from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25DF081, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF081 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Atmel AT25DF081A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF081A from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Atmel AT25DF161, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF161 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT25DF321, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF321 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT25DF321A, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF321A from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT25DF641(A), 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DF641(A) from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT25DL081, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DL081 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Atmel AT25DL161, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DL161 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT25DQ161, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25DQ161 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT25F512, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F512 from 0x00000000ffff0000 to 0x00000008007c8000 Invalid OPCODE 0x15, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25F512A, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F512A from 0x00000000ffff0000 to 0x00000008007c8000 Invalid OPCODE 0x15, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25F512B, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F512B from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25F1024(A), 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F1024(A) from 0x00000000fffe0000 to 0x00000008007c8000 Invalid OPCODE 0x15, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25F2048, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F2048 from 0x00000000fffc0000 to 0x00000008007c8000 Invalid OPCODE 0x15, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25F4096, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25F4096 from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0x15, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25FS010, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25FS010 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT25FS040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT25FS040 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT26DF041, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT26DF041 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT26DF081A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping AT26DF081A from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Atmel AT26DF161, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT26DF161 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT26DF161A, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT26DF161A from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT26F004, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT26F004 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT45CS1282, 16896 kB: page_size=1000 pre-rounding: start=0x00000000fef80000, len=0x1080000, end=0x0000000100000000 post-rounding: start=0x00000000fef80000, len=0x1080000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45CS1282 from 0x00000000fef80000 to 0x0000000802180000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802180000, len=0x1080000, end=0x0000000803200000 post-rounding: start=0x0000000802180000, len=0x1080000, end=0x0000000803200000 programmer_unmap_flash_region: unmapped 0x0000000802180000 Probing for Atmel AT45DB011D, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB011D from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT45DB021D, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB021D from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT45DB041D, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB041D from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT45DB081D, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB081D from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Atmel AT45DB161D, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB161D from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Atmel AT45DB321C, 4224 kB: page_size=1000 pre-rounding: start=0x00000000ffbe0000, len=0x420000, end=0x0000000100000000 post-rounding: start=0x00000000ffbe0000, len=0x420000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB321C from 0x00000000ffbe0000 to 0x00000008021e0000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008021e0000, len=0x420000, end=0x0000000802600000 post-rounding: start=0x00000008021e0000, len=0x420000, end=0x0000000802600000 programmer_unmap_flash_region: unmapped 0x00000008021e0000 Probing for Atmel AT45DB321D, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB321D from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT45DB321E, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB321E from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Atmel AT45DB642D, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping AT45DB642D from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for ESMT F25L008A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping F25L008A from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for ESMT F25L32PA, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping F25L32PA from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25B05, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B05 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B05T, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B05T from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25P05, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P05 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B10T, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B10T from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25P10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B20T, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B20T from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25P20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B40T, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B40T from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25P40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25B80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25B80T, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B80T from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25P80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25B16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25B16T, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B16T from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25P16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25B32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25B32T, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B32T from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25P32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25B64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25B64T, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25B64T from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25P64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25P64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25F05, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F05 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25F10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25F20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25F40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25F80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25F16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25F32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25F64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25F64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25Q40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25Q80(A), 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q80(A) from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25Q16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25Q32(A/B), 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q32(A/B) from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25Q64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25Q128, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25Q128 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25QH16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25QH16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25QH32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25QH32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25QH64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25QH64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Found Eon flash chip "EN25QH64" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Chip status register is 0x00. Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set Chip status register: Bit 6 is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25QH128, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25QH128 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25S10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25S20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25S40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Eon EN25S80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Eon EN25S16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Eon EN25S32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Eon EN25S64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25S64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for ESI ES25P40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping ES25P40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for ESI ES25P80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping ES25P80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for ESI ES25P16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping ES25P16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for GigaDevice GD25LQ40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25LQ80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for GigaDevice GD25LQ16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for GigaDevice GD25LQ32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25LQ64(B), 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ64(B) from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25LQ128, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25LQ128 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25Q512, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q512 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25Q10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25Q20(B), 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q20(B) from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25Q40(B), 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q40(B) from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25Q80(B), 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q80(B) from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for GigaDevice GD25Q16(B), 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q16(B) from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for GigaDevice GD25Q32(B), 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q32(B) from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25Q64(B), 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q64(B) from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25Q128B, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q128B from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25Q128C, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25Q128C from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for GigaDevice GD25T80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25T80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for GigaDevice GD25VQ21B, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25VQ21B from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25VQ40C, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25VQ40C from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25VQ41B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25VQ41B from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for GigaDevice GD25VQ80C, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25VQ80C from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for GigaDevice GD25VQ16C, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping GD25VQ16C from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Intel 25F160S33B8, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F160S33B8 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Intel 25F160S33T8, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F160S33T8 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Intel 25F320S33B8, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F320S33B8 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Intel 25F320S33T8, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F320S33T8 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Intel 25F640S33B8, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F640S33B8 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Intel 25F640S33T8, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping 25F640S33T8 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX23L1654, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX23L1654 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX23L3254, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX23L3254 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX23L6454, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX23L6454 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX23L12854, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping MX23L12854 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L512(E)/MX25V512(C) from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1005(C)/MX25L1006E from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Macronix MX25L2005(C)/MX25L2006E, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L2005(C)/MX25L2006E from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Macronix MX25L4005(A/C)/MX25L4006E, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L4005(A/C)/MX25L4006E from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Macronix MX25L8005/MX25L8006E/MX25L8008E/MX25V8005, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L8005/MX25L8006E/MX25L8008E/MX25V8005 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Macronix MX25L1605, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1605 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25L1605A/MX25L1606E/MX25L1608E, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1605A/MX25L1606E/MX25L1608E from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1605D/MX25L1608D/MX25L1673E from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25L1635D, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1635D from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25L1635E, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L1635E from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25L3205(A), 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L3205(A) from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L3205D/MX25L3208D from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L3206E/MX25L3208E, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L3206E/MX25L3208E from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L3273E, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L3273E from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L3235D, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L3235D from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L6405, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L6405 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L6405D, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L6405D from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L6406E/MX25L6408E from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L6436E/MX25L6445E/MX25L6465E/MX25L6473E, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L6436E/MX25L6445E/MX25L6465E/MX25L6473E from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L12805D, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L12805D from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L12835F/MX25L12845E/MX25L12865E, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L12835F/MX25L12845E/MX25L12865E from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25U1635E, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25U1635E from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Macronix MX25U3235E/F, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25U3235E/F from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25U6435E/F, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25U6435E/F from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25U12835F, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25U12835F from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Macronix MX25L6495F, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping MX25L6495F from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P05-A from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P05, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P05 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. Ignoring RES in favour of RDID. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P10-A, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P10-A from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. Ignoring RES in favour of RDID. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P20-old from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. Ignoring RES in favour of RDID. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P40-old from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. Ignoring RES in favour of RDID. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25P80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Micron/Numonyx/ST M25P16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Micron/Numonyx/ST M25P32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M25P64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M25P128, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping M25P128 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M25PE10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PE10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25PE20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PE20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25PE40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PE40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PE80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PE16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PX80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PX16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PX32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping M25PX64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST M45PE10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping M45PE10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M45PE20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping M45PE20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M45PE40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M45PE40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M45PE80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping M45PE16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q016 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q032..1E from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q032..3E from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q064..1E from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q064..3E from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q128..1E from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping N25Q128..3E from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Nantronics N25S10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping N25S10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Nantronics N25S20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping N25S20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Nantronics N25S40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping N25S40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Nantronics N25S80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping N25S80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Nantronics N25S16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping N25S16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for PMC Pm25LD256C, 32 kB: page_size=1000 pre-rounding: start=0x00000000ffff8000, len=0x8000, end=0x0000000100000000 post-rounding: start=0x00000000ffff8000, len=0x8000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LD256C from 0x00000000ffff8000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x8000, end=0x00000008007d0000 post-rounding: start=0x00000008007c8000, len=0x8000, end=0x00000008007d0000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LD512(C), 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LD512(C) from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LD010(C), 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LD010(C) from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LD020(C), 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LD020(C) from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LD040(C), 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LD040(C) from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LQ020, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LQ020 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LQ040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LQ040 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LQ080, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LQ080 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for PMC Pm25LQ016, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LQ016 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for PMC Pm25LQ032C, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LQ032C from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for PMC Pm25LV512(A), 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV512(A) from 0x00000000ffff0000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LV010, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV010 from 0x00000000fffe0000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LV010A, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV010A from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LV020, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV020 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LV040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV040 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm25LV080B, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV080B from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for PMC Pm25LV016B, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm25LV016B from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Sanyo LE25FW106, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW106 from 0x00000000fffe0000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FW406A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW406A from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FU406B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FU406B from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FU406C/LE25U40CMC, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FU406C/LE25U40CMC from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FW203A, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW203A from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FW403A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW403A from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FW418A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW418A from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sanyo LE25FW806, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW806 from 0x00000000fff00000 to 0x00000008014a4000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Sanyo LE25FW808, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping LE25FW808 from 0x00000000fff00000 to 0x00000008014a4000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Spansion S25FL004A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL004A from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Spansion S25FL008A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL008A from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Spansion S25FL016A, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL016A from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Spansion S25FL032A/P, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL032A/P from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL064A/P, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL064A/P from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL204K, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL204K from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Spansion S25FL208K, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL208K from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL116K/S25FL216K from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Spansion S25FL132K, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL132K from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL164K, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL164K from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL127S-64kB, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL127S-64kB from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL127S-256kB, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL127S-256kB from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL128P......0, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL128P......0 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL128P......1, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL128P......1 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL128S......0, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL128S......0 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL128S......1, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL128S......1 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL129P......0, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL129P......0 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Spansion S25FL129P......1, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping S25FL129P......1 from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for SST SST25LF020A, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25LF020A from 0x00000000fffc0000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25LF040A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25LF040A from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25LF080(A), 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25LF080(A) from 0x00000000fff00000 to 0x00000008014a4000 Invalid OPCODE 0xab, will not execute. page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST25VF512(A), 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF512(A) from 0x00000000ffff0000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF010(A), 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF010(A) from 0x00000000fffe0000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF020, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF020 from 0x00000000fffc0000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF020B, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF020B from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF040 from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF040B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF040B from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25VF040B.REMS, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF040B.REMS from 0x00000000fff80000 to 0x00000008007c8000 Invalid OPCODE 0x90, will not execute. page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF020A, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF020A from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF040B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF040B from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF080B, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF080B from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST25VF080B, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF080B from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST25VF016B, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF016B from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for SST SST25VF032B, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF032B from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for SST SST25VF064C, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25VF064C from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for SST SST25WF512, 64 kB: page_size=1000 pre-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 post-rounding: start=0x00000000ffff0000, len=0x10000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF512 from 0x00000000ffff0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 post-rounding: start=0x00000008007c8000, len=0x10000, end=0x00000008007d8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF010, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF010 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF020, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF020 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF040 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST25WF080, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST25WF080 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W25Q40.V, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q40.V from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25Q80.V, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q80.V from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W25Q16.V, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q16.V from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Winbond W25Q32.V, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q32.V from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25Q64.V, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q64.V from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25Q128.V, 16384 kB: page_size=1000 pre-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 post-rounding: start=0x00000000ff000000, len=0x1000000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q128.V from 0x00000000ff000000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 post-rounding: start=0x0000000802000000, len=0x1000000, end=0x0000000803000000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25Q20.W, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q20.W from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25Q40.W, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q40.W from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25Q80.W, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q80.W from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W25Q16.W, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q16.W from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Winbond W25Q32.W, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q32.W from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25Q64.W, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping W25Q64.W from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25X10, 128 kB: page_size=1000 pre-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 post-rounding: start=0x00000000fffe0000, len=0x20000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X10 from 0x00000000fffe0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 post-rounding: start=0x00000008007c8000, len=0x20000, end=0x00000008007e8000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25X20, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X20 from 0x00000000fffc0000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25X40, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X40 from 0x00000000fff80000 to 0x00000008007c8000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W25X80, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X80 from 0x00000000fff00000 to 0x00000008014a4000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W25X16, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X16 from 0x00000000ffe00000 to 0x0000000801600000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for Winbond W25X32, 4096 kB: page_size=1000 pre-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 post-rounding: start=0x00000000ffc00000, len=0x400000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X32 from 0x00000000ffc00000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 post-rounding: start=0x0000000802000000, len=0x400000, end=0x0000000802400000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Winbond W25X64, 8192 kB: page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping W25X64 from 0x00000000ff800000 to 0x0000000802000000 RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Probing for Unknown SFDP-capable chip, 0 kB: spi_sfdp_read_sfdp_chunk: addr=0x0, len=2, data: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17 0x1c. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Atmel unknown Atmel SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Eon unknown Eon SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Macronix unknown Macronix SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for PMC unknown PMC SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for SST unknown SST SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for ST unknown ST SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Generic unknown SPI chip (RDID), 0 kB: RDID returned 0x1c 0x70 0x17. probe_spi_rdid_generic: id1 0x1c, id2 0x7017 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping AT49LH002 from 0x00000000fffc0000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffbc0000 to 0x0000000800808000 probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 post-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x0000000800808000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT49LH00B4, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT49LH00B4 from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Atmel AT49LH004, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping AT49LH004 from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Intel 82802AB, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping 82802AB from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Intel 82802AC, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping 82802AC from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for PMC Pm49FL002, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm49FL002 from 0x00000000fffc0000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffbc0000 to 0x0000000800808000 probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 post-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x0000000800808000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for PMC Pm49FL004, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping Pm49FL004 from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Sharp LHF00L04, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping LHF00L04 from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST49LF002A/B, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF002A/B from 0x00000000fffc0000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffbc0000 to 0x0000000800808000 probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 post-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x0000000800808000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST49LF003A/B, 384 kB: page_size=1000 pre-rounding: start=0x00000000fffa0000, len=0x60000, end=0x0000000100000000 post-rounding: start=0x00000000fffa0000, len=0x60000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF003A/B from 0x00000000fffa0000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffba0000, len=0x60000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffba0000, len=0x60000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffba0000 to 0x0000000800828000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000800828000, len=0x60000, end=0x0000000800888000 post-rounding: start=0x0000000800828000, len=0x60000, end=0x0000000800888000 programmer_unmap_flash_region: unmapped 0x0000000800828000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x60000, end=0x0000000800828000 post-rounding: start=0x00000008007c8000, len=0x60000, end=0x0000000800828000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST49LF004A/B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF004A/B from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST49LF004C, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF004C from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for SST SST49LF008A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF008A from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST49LF008C, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF008C from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for SST SST49LF016C, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping SST49LF016C from 0x00000000ffe00000 to 0x0000000801600000 page_size=1000 pre-rounding: start=0x00000000ffa00000, len=0x200000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffa00000, len=0x200000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffa00000 to 0x0000000802000000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000802000000, len=0x200000, end=0x0000000802200000 post-rounding: start=0x0000000802000000, len=0x200000, end=0x0000000802200000 programmer_unmap_flash_region: unmapped 0x0000000802000000 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for ST M50FLW040A, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FLW040A from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for ST M50FLW040B, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FLW040B from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for ST M50FLW080A, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FLW080A from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for ST M50FLW080B, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FLW080B from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for ST M50FW002, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FW002 from 0x00000000fffc0000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffbc0000, len=0x40000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffbc0000 to 0x0000000800808000 probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 post-rounding: start=0x0000000800808000, len=0x40000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x0000000800808000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for ST M50FW016, 2048 kB: page_size=1000 pre-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 post-rounding: start=0x00000000ffe00000, len=0x200000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FW016 from 0x00000000ffe00000 to 0x0000000801600000 page_size=1000 pre-rounding: start=0x00000000ffa00000, len=0x200000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffa00000, len=0x200000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffa00000 to 0x0000000802000000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x0000000802000000, len=0x200000, end=0x0000000802200000 post-rounding: start=0x0000000802000000, len=0x200000, end=0x0000000802200000 programmer_unmap_flash_region: unmapped 0x0000000802000000 page_size=1000 pre-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 post-rounding: start=0x0000000801600000, len=0x200000, end=0x0000000801800000 programmer_unmap_flash_region: unmapped 0x0000000801600000 Probing for ST M50FW040, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FW040 from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for ST M50FW080, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping M50FW080 from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W39V040FA, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W39V040FA from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W39V040FB, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W39V040FB from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W39V040FC, 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W39V040FC from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W49V002FA, 256 kB: page_size=1000 pre-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 post-rounding: start=0x00000000fffc0000, len=0x40000, end=0x0000000100000000 programmer_map_flash_region: mapping W49V002FA from 0x00000000fffc0000 to 0x00000008007c8000 probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 post-rounding: start=0x00000008007c8000, len=0x40000, end=0x0000000800808000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Probing for Winbond W39V080FA, 1024 kB: page_size=1000 pre-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 post-rounding: start=0x00000000fff00000, len=0x100000, end=0x0000000100000000 programmer_map_flash_region: mapping W39V080FA from 0x00000000fff00000 to 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb00000, len=0x100000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb00000 to 0x00000008015a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 post-rounding: start=0x00000008015a4000, len=0x100000, end=0x00000008016a4000 programmer_unmap_flash_region: unmapped 0x00000008015a4000 page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 post-rounding: start=0x00000008014a4000, len=0x100000, end=0x00000008015a4000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 Probing for Winbond W39V080FA (dual mode), 512 kB: page_size=1000 pre-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 post-rounding: start=0x00000000fff80000, len=0x80000, end=0x0000000100000000 programmer_map_flash_region: mapping W39V080FA (dual mode) from 0x00000000fff80000 to 0x00000008007c8000 page_size=1000 pre-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 post-rounding: start=0x00000000ffb80000, len=0x80000, end=0x00000000ffc00000 programmer_map_flash_region: mapping flash chip registers from 0x00000000ffb80000 to 0x00000008014a4000 probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content page_size=1000 pre-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 post-rounding: start=0x00000008014a4000, len=0x80000, end=0x0000000801524000 programmer_unmap_flash_region: unmapped 0x00000008014a4000 page_size=1000 pre-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 post-rounding: start=0x00000008007c8000, len=0x80000, end=0x0000000800848000 programmer_unmap_flash_region: unmapped 0x00000008007c8000 Found Eon flash chip "EN25QH64" (8192 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). page_size=1000 pre-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 post-rounding: start=0x00000000ff800000, len=0x800000, end=0x0000000100000000 programmer_map_flash_region: mapping EN25QH64 from 0x00000000ff800000 to 0x0000000802000000 Block protection is disabled. Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=1 Running OPCODE 0x03 failed at address 0x003000 (payload length was 64). Read operation failed! FAILED. page_size=1000 pre-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 post-rounding: start=0x0000000802000000, len=0x800000, end=0x0000000802800000 programmer_unmap_flash_region: unmapped 0x0000000802000000 Restoring MMIO space at 0x8007c78a0 Restoring PCI config space for 00:1f:0 reg 0xdc

2 1

[GSoC] Implement Obscure Features, Locking/Unlocking of Access Protection, and Add CFI Support
by Hatim Kanchwala 23 Mar '16

23 Mar '16

Hello, Here's the link to the first draft of my GSoC proposal https://docs.google.com/document/d/1-DyUPSxbLxgPPVtVyLs2B810m1f6j6XiA-l0cLv…. I would love to hear any feedback. The deadline is a day away. Thanks for your time :) -- Kind Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 0

SPI support for intel i82580
by Michael Stickel 23 Mar '16

23 Mar '16

Hi, we have a added and tested support for the intel i82580 to the nicintel_spi driver. Is anyone else working on that topic or should I post the patch. This could conflict with the i350 patch http://patchwork.coreboot.org/patch/4394/. Should our patch be based on a clear 0.9.9 release or on a 0.9.9 + i350 patch. Background: the intel i82580 quad ethernet controller has two memories. One 16KB or 32KB spi-eeprom for MAC address and other configurations and one 512KB spi-flash for the firmware. the spi-eeprom can be written with the driver nicintel_eeprom. We made the nessesary modifications in the nicintel_spi driver based on the 0.9.9 release. best regards Michael

2 2

W836xx: EP35-DS4: flashrom -V
by Седельников Игорь 23 Mar '16

23 Mar '16

flashrom v0.9.6.1-r1563 on Linux 4.2.0-34-generic (x86_64) flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (5 args): flashrom -p internal -V -o fr-pi-V.log Calibrating delay loop... OS timer resolution is 1 usecs, 2057M loops per second, 10 myus = 10 us, 100 myus = 103 us, 1000 myus = 1029 us, 10000 myus = 10291 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "EP35-DS4" DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "EP35-DS4" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 87. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE Super I/O, ID 0x8718 on port 0x2e Found chipset "Intel ICH9R" with PCI ID 8086:2916. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0x464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x2000 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=0, SCIP=0, FDOPSS=1, FDV=0, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x08: 0x00000000 (FADDR) 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) 0x90: 0x04 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0x004140 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=4, DBC=1, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) SPI Read Configuration: prefetching disabled, caching enabled, OK. No IT87* serial flash segment enabled. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0xbf, id2 0x8e Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0xbf, id2 0x8e Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xbf, id2 0x8e Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xbf, id2 0x8e Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xbf, id2 0x8e Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Chip status register is 00 Chip status register: Block Protect Write Disable (BPL) is not set Chip status register: Auto Address Increment Programming (AAI) is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found SST flash chip "SST25VF080B" (1024 kB, SPI) at physical address 0xfff00000. Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 Signature = 0xffffffff (should be 0x50444653) No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xbf, id2 0x258e Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xbf, id2 0x8e Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x55, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x55, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x55, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x22, id2 0xac, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x55, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x55, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x24, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found SST flash chip "SST25VF080B" (1024 kB, SPI). No operations were specified. Restoring MMIO space at 0x7f3796a358a0 Restoring MMIO space at 0x7f3796a3589c Restoring MMIO space at 0x7f3796a35898 Restoring MMIO space at 0x7f3796a35896 Restoring MMIO space at 0x7f3796a35894 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

Flashing a Winbond W25Q64FV using a RaspberrPI model B
by Emanuele Santoro 22 Mar '16

22 Mar '16

Hello everybody! I am trying to revive a Dell XPS15 9530 laptop whose BIOS was corrupted during a BIOS update (this seems to be a fairly common problem with this laptop) and I am having some troubles. The BIOS chip is a Winbond flash: 25Q64FVS1Q (this is what is written on the chip, assuming I read that correctly). I am using a RaspberryPI model B (one of the first units issued), its SPI interface and a pair of test clips (the chip is a SOIC8 unit, soldered on the mother board). The operating system is Raspbian GNU/Linux (freshly installed last week). uname -a from PI is: Linux raspberrypi 4.1.19+ #853 Wed Mar 9 18:04:48 GMT 2016 armv6l GNU/Linux The spi modules (spidev and spi_bcm2708) seems to be built into the kernel, as the devices appear in /dev but modprobing the kernel modules result in errors. I built flashrom from sources (checked out from the svn trunk): flashrom v0.9.9-r1954 on Linux 4.1.19+ (armv6l) So this is the environment. Please note that before attempting anything, I disconnected the CMOS battery as well as the main battery. Power supply is also disconnected, and has been disconnected for the last three weeks. First things first, when I try to probe the chip, flashrom cannot manage to probe the chip at all, and i get this message: Calibrating delay loop... delay loop is unreliable, trying to continue OK. Today I tried again, and finally got this message: root@raspberrypi:~# flashrom -p linux_spi:dev=/dev/spidev0.0 flashrom v0.9.9-r1954 on Linux 4.1.19+ (armv6l) flashrom is free software, get the source code at https://flashrom.org Calibrating delay loop... delay loop is unreliable, trying to continue OK. Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI) on linux_spi. === This flash part has status NOT WORKING for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash chip. Please include the flashrom log file for all operations you tested (see the man page for details), and mention which mainboard or programmer you tested in the subject line. Thanks for your help! No operations were specified. root@raspberrypi:~# Now... 1. I do not trust this RaspberryPI completely (I bought it second hand, and it has always worked somehow weirdly). I will try with another RaspberryPI as soon as I can find someone to lend me one. 2. Is this chip even supported? Can support be added? If you suggest me what sources to look at I might try and add support for it myself, otherwise I'd be happy to help someone add support this chip. 3. does the "unknown SPI chip (RDID)" mean that the chip is damaged and needs to be replaced? 4. Shoud I get a Bus Pirate? Is it so much better than Raspberry PI at this sort of stuff? 5. Any hints / suggestions in general? Thanks in advance, -- Emanuele Santoro

2 1

W836xx: Lenovo 3460AQG: flashrom -V
by Thomas Nilsen 20 Mar '16

20 Mar '16

flashrom v0.9.7-r1852 on Linux 4.2.0-34-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.1, GCC 4.9.1, little endian Command line (3 args): flashrom -V --programmer internal Calibrating delay loop... OS timer resolution is 1 usecs, 3174M loops per second, 10 myus = 10 us, 100 myus = 108 us, 1000 myus = 1001 us, 10000 myus = 9986 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. No DMI table found. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 00. Please send the output of "flashrom -V -p internal" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found chipset "Intel QS77" with PCI ID 8086:1e56. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: enabled (A16(+) inverted) 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x0 0xffe00000/0xffa00000 FWH IDSEL: 0x0 0xffd80000/0xff980000 FWH IDSEL: 0x0 0xffd00000/0xff900000 FWH IDSEL: 0x0 0xffc80000/0xff880000 FWH IDSEL: 0x0 0xffc00000/0xff800000 FWH IDSEL: 0xf 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x380000 bytes SPI Read Configuration: prefetching enabled, caching enabled, BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. SPIBAR = 0x00007ffa22eea000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x3f00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x0bff0500 FREG1: BIOS region (0x00500000-0x00bfffff) is read-write. 0x5C: 0x04ff0003 FREG2: Warning: Management Engine region (0x00003000-0x004fffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see http://flashrom.org/ME for details. 0x74: 0x8aaf0800 PR0: Warning: 0x00800000-0x00aaffff is read-only. 0x78: 0x8ade0ad0 PR1: Warning: 0x00ad0000-0x00adefff is read-only. 0x7C: 0x8b100b10 PR2: Warning: 0x00b10000-0x00b10fff is read-only. 0x80: 0x8bff0b40 PR3: Warning: 0x00b40000-0x00bfffff is read-only. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0xc0 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x0606 (PREOP) 0x96: 0x0fe4 (OPTYPE) 0x98: 0x02030105 (OPMENU) 0x9C: 0xff9f20d8 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xD0: 0x00000000 (FPB) Enabling hardware sequencing due to multiple flash chips detected. PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 2 attached SPI flash chips with a combined density of 12288 kB. There is only one partition containing the whole address space (0x000000 - 0xbfffff). There are 3072 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific) mapped at physical address 0x0000000000000000. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x01, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x01, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x01, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x28, id2 0x68, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0x29, id2 0xc1, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x01, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0x29, id2 0xc1, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x01, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xec, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific). No operations were specified. Restoring MMIO space at 0x7ffa22eed8a0 Restoring PCI config space for 00:1f:0 reg 0xdc --------------- dmidecode output for machine & bios; Handle 0x000C, DMI type 0, 24 bytes BIOS Information Vendor: LENOVO Version: G6ETB2WW (2.72 ) Release Date: 10/08/2015 Address: 0xE0000 Runtime Size: 128 kB ROM Size: 12288 kB Characteristics: PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed Boot from CD is supported Selectable boot is supported EDD is supported 3.5"/720 kB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported BIOS boot specification is supported Targeted content distribution is supported UEFI is supported BIOS Revision: 2.72 Firmware Revision: 1.6 Handle 0x000D, DMI type 1, 27 bytes System Information Manufacturer: LENOVO Product Name: 3460AQG Version: ThinkPad X1 Carbon Serial Number: ****** UUID: ****** Wake-up Type: Power Switch SKU Number: LENOVO_MT_3460 Family: ThinkPad X1 Carbon -- *Thomas Nilsen* 3mt Communications AS PB 195, 1112 Oslo, Norway (+47) 41888888 | thomas(a)3mt.no | www.3mt.no

1 0

Failed to flash my APU2
by Kalle Svensson 20 Mar '16

20 Mar '16

Hi team! I'm trying to flash my APU2 per the instructions at: http://pcengines.ch/howto.htm#bios and I get this: root@fw:/usr/home/kalle # flashrom -w apu2_160311.rom -p internal flashrom v0.9.7-r1711 on FreeBSD 10.2-RELEASE-p14 (amd64) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. coreboot table found at 0xdffae000. Found chipset "AMD FCH". Enabling flash write... FCH device found but SMBus revision 0x42 does not match known values. Please report this to flashrom(a)flashrom.org and include this log and the output of lspci -nnvx, thanks!. root@fw:/usr/home/kalle # pciconf -l -bcevV > pciconf.out (out file attached) root@fw:/usr/home/kalle # uname -a FreeBSD fw 10.2-RELEASE-p14 FreeBSD 10.2-RELEASE-p14 #0: Wed Mar 16 20:46:12 UTC 2016 root@amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64 Any pointers on how to proceed would be greatly appreciated! :-) ///Kalle

1 1

I can't program PLCC32 using an DIP32 adapter on Abit BF6
by Gelip 17 Mar '16

17 Mar '16

The standard motherboard has a chip WINBOND 2Mbit (256kB). For the purposes of coreboot replaced it to EON 256kB. Now I want to use a larger chip 4Mbit (512kB) PLCC32 but using adapter PLCC32-DIP32. I want to do it using the method of hot swap replacing chip 256kB to 512kB while running Debian with flashrom. I built Coreboot size 512kB but I have a problem with programming using flashrom. I tried version 0.9.7 and the latest 0.9.9. The same problem is when I boot the computer from bios AWARD 256kB and from Coreboot 256kB. I use Debian Live 6.0.5 Standard from PXE server. Boot from AWARD bios 256kB chip WINBOND, flashrom 0.9.7 - http://paste.flashrom.org/view.php?id=2903 Boot from Coreboot bios 256kB chip EON, flashrom 0.9.9 - http://paste.flashrom.org/view.php?id=2904

1 0

Windbond W25Q128 SPI 16MB flash chip - Successful write/read
by Arnold Gonzalez 16 Mar '16

16 Mar '16

THANK YOU for making this software. I can say that it saved us a ton of money, we no longer have to RMA systems that have been bricked. I can help out by testing more types of systems/chips. My employer is unixsurplus and we are a partner of SuperMicro, and we deal with server manufacturers such as Dell, Quanta, SGI, Rackable systems, Cisco, HP, Sun. Just shoot me an email and I will be glad to run tests for you. -Arnold root@us:~/Desktop# flashrom -r X10DRU5.C17 -p internal flashrom v0.9.6.1-r1563 on Linux 4.2.0-16-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "Intel ICH10R". Enabling flash write... OK. Found Winbond flash chip "W25Q128" (16384 kB, SPI) at physical address 0xff000000. === This flash part has status UNTESTED for operations: READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -VE, -Vw), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... done. root@us:~/Desktop# flashrom -r X10DRU5.C17 -p internal -V flashrom v0.9.6.1-r1563 on Linux 4.2.0-16-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (5 args): flashrom -r X10DRU5.C17 -p internal -V Calibrating delay loop... OS timer resolution is 1 usecs, 1065M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1005 us, 10000 myus = 10060 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Supermicro" DMI string system-product-name: "X8DT6" DMI string system-version: "1234567890" DMI string baseboard-manufacturer: "Supermicro" DMI string baseboard-product-name: "X8DT6" DMI string baseboard-version: "1234567890" DMI string chassis-type: "Main Server Chassis" Found Winbond Super I/O, id 52 Found chipset "Intel ICH10R" with PCI ID 8086:3a16. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0x460: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x2008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=0, FLOCKDN=0 Programming OPCODES... done 0x08: 0x00ffffc0 (FADDR) 0x90: 0x04 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0x007f10 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) SPI Read Configuration: prefetching disabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x17, id2 0x17 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x17, id2 0x17 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Chip status register is 00 Found Winbond flash chip "W25Q128" (16384 kB, SPI) at physical address 0xff000000. Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Unknown SFDP-capable chip, 0 kB: Parsing JEDEC flash parameter table... done. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xef, id2 0x17 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x80, id2 0x7d, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x80, id2 0x7d, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x80, id2 0x7d, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x33, id2 0xc0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x80, id2 0x7d, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x80, id2 0x7d, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x50, id2 0x8d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q128" (16384 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). === This flash part has status UNTESTED for operations: READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -VE, -Vw), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... done. Restoring MMIO space at 0x7fbb238fc8a0 Restoring MMIO space at 0x7fbb238fc89c Restoring MMIO space at 0x7fbb238fc898 Restoring MMIO space at 0x7fbb238fc896 Restoring MMIO space at 0x7fbb238fc894 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

W836xx: HP Z440: flashrom -V
by Jan P. Monsch 16 Mar '16

16 Mar '16

Hi, Find enclosed the output of flashrom for a HP Z440 which does not seem to be supported. Jan jpm@wall-e:~$ sudo flashrom -p internal -r test.bin flashrom v0.9.8-r1888 on Linux 4.2.0-30-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Active config mode, unknown reg 0x20 ID: 1c. Please send the output of "flashrom -V -p internal" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found chipset "Intel C610/X99 (Wellsburg)". This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. Warning: SPI Configuration Lockdown activated. FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. FREG2: Warning: Management Engine region (0x00005000-0x005fffff) is locked. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see http://flashrom.org/ME for details. PR0: Warning: 0x00e7f000-0x00ffffff is read-only. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). PROBLEMS, continuing anyway Found Winbond flash chip "W25Q128.V" (16384 kB, SPI) mapped at physical address 0x00000000ff000000. Reading flash... Transaction error! Read operation failed! FAILED. jpm@wall-e:~$ sudo flashrom -V -p internal flashrom v0.9.8-r1888 on Linux 4.2.0-30-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.1, GCC 4.8.4, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 3458M loops per second, 10 myus = 9 us, 100 myus = 99 us, 1000 myus = 991 us, 10000 myus = 9908 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Mini Tower" DMI string system-manufacturer: "Hewlett-Packard" DMI string system-product-name: "HP Z440 Workstation" DMI string system-version: "Not Specified" DMI string baseboard-manufacturer: "Hewlett-Packard" DMI string baseboard-product-name: "212B" DMI string baseboard-version: "unknown" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 1c. Please send the output of "flashrom -V -p internal" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found chipset "Intel C610/X99 (Wellsburg)" with PCI ID 8086:8d44. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc25: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (unknown) Top Swap: not enabled 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI Read Configuration: prefetching enabled, caching enabled, BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. SPIBAR = 0x00007f161f33b000 + 0x3800 0x04: 0xf008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x3f00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 0x50: 0x00005a5b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x5a, BRRA 0x5b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x0fff0600 FREG1: BIOS region (0x00600000-0x00ffffff) is read-write. 0x5C: 0x05ff0005 FREG2: Warning: Management Engine region (0x00005000-0x005fffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00040003 FREG4: Platform Data region (0x00003000-0x00004fff) is read-write. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see http://flashrom.org/ME for details. 0x74: 0x8fff0e7f PR0: Warning: 0x00e7f000-0x00ffffff is read-only. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0xc4 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xfc0000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=4 0x94: 0x5006 (PREOP) 0x96: 0x4ed0 (OPTYPE) 0x98: 0x0201009f (OPMENU) 0x9C: 0xc7052003 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x80802025 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x0000d817 (UVSCC) UVSCC: BES=0x3, WG=1, WSR=0, WEWS=1, EO=0xd8 0xD0: 0x50444653 (FPB) PROBLEMS, continuing anyway The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DL081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DL161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25F512, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512A, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25F1024(A), 128 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F2048, 256 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F4096, 512 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ESMT F25L32PA, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX23L1654, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX23L3254, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX23L6454, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX23L12854, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L2005(C)/MX25L2006E, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L4005(A/C)/MX25L4006E, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L8005/MX25L8006E/MX25L8008E/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1605A/MX25L1606E/MX25L1608E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3206E/MX25L3208E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3273E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6405D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6436E/MX25L6445E/MX25L6465E/MX25L6473E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L12805D, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L12835F/MX25L12845E/MX25L12865E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25U12835F, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6495F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV512(A), 64 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo LE25FW106, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW406A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FU406B, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo LE25FW418A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW806, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW808, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL132K, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL164K, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL127S-64kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL127S-256kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL128P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL128P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL128S......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL128S......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL129P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL129P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25LF020A, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080(A), 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF512(A), 64 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF010(A), 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020B, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25WF080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q40.V, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Found Winbond flash chip "W25Q128.V" (16384 kB, SPI) mapped at physical address 0x00000000ff000000. Chip status register is 0x00. Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0x74, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0x74, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xe8, id2 0x54, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x24, id2 0x10, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q128.V" (16384 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). No operations were specified. Restoring MMIO space at 0x7f161f33e8a0 Restoring PCI config space for 00:1f:0 reg 0xdc jpm@wall-e:~$

1 0

Asus B150M-C Logs
by Lars Möller 16 Mar '16

16 Mar '16

Hi, i successfully flashed this new chip. greets Lars -- Lars Möller Idenbrockweg 235 48159 Münster Germany Tel. 0251 5908618 Mobil 0177 5211752

1 0

[PATCH 1/2] Add support for GD25LQ05B, GD25LQ10B, GD25LQ20B, GD25LQ40B and GD25LQ80B
by Hatim Kanchwala 16 Mar '16

16 Mar '16

Hello, Definitions for 40B/80B are merged with their non-B counterparts, defines for 10B/20B are added in header, and support for 05B is added (untested, chip not in samples). Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> --- flashchips.c | 135 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++-- flashchips.h | 7 +++- 2 files changed, 136 insertions(+), 6 deletions(-) diff --git a/flashchips.c b/flashchips.c index 0fc1b7a..3235b59 100644 --- a/flashchips.c +++ b/flashchips.c @@ -5628,37 +5628,162 @@ const struct flashchip flashchips[] = { {16 * 1024, 1}, }, .block_erase = erase_block_jedec, }, { .eraseblocks = { {2048 * 1024, 1} }, .block_erase = erase_chip_block_jedec, }, }, .write = write_jedec_1, /* Supports a fast mode too */ .read = read_memmapped, .voltage = {3000, 3600}, /* 3.0-3.6V for type -70, others 2.7-3.6V */ }, { .vendor = "GigaDevice", - .name = "GD25LQ40", + .name = "GD25LQ05B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25LQ05B, + .total_size = 64, + .page_size = 256, + /* Supports SFDP */ + /* OTP: 1536B total; read 0x48; write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 16} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 2} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd status reg (read 0x35); 3rd status reg (read 0x15) */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {1650, 2100}, + }, + + + { + .vendor = "GigaDevice", + .name = "GD25LQ10B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25LQ10B, + .total_size = 128, + .page_size = 256, + /* Supports SFDP */ + /* OTP: 1536B total; read 0x48; write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 32} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 4} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 2} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {128 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {128 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd status reg (read 0x35); 3rd status reg (read 0x15) */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {1650, 2100}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25LQ20B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25LQ20B, + .total_size = 256, + .page_size = 256, + /* OTP: 1536B total; read 0x48; write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 8} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd status reg (read 0x35); 3rd status reg (read 0x15) */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {1650, 2100}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25LQ40(B)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25LQ40, .total_size = 512, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ + /* OTP (GD25LQ40): 1024B total, 256B reserved; read 0x48, write 0x42, erase 0x44 */ + /* OTP (GD25LQ40B): 1536B total; read 0x48, write 0x42, erase 0x44 */ + /* GD25LQ40B supports SFDP */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 128} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 16} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 8} }, .block_erase = spi_block_erase_d8, @@ -5667,37 +5792,39 @@ const struct flashchip flashchips[] = { .block_erase = spi_block_erase_60, }, { .eraseblocks = { {512 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {1695, 1950}, }, { .vendor = "GigaDevice", - .name = "GD25LQ80", + .name = "GD25LQ80(B)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25LQ80, .total_size = 1024, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ + /* OTP (GD25LQ80): 1024B total, 256B reserved; read 0x48, write 0x42, erase 0x44 */ + /* OTP (GD25LQ80B): 1536B total; read 0x48, write 0x42, erase 0x44 */ + /* GD25LQ80B supports SFDP */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { { .eraseblocks = { {4 * 1024, 256} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {32 * 1024, 32} }, .block_erase = spi_block_erase_52, }, { .eraseblocks = { {64 * 1024, 16} }, .block_erase = spi_block_erase_d8, diff --git a/flashchips.h b/flashchips.h index 9ffb30f..07abd74 100644 --- a/flashchips.h +++ b/flashchips.h @@ -364,32 +364,35 @@ #define GIGADEVICE_ID 0xC8 /* GigaDevice */ #define GIGADEVICE_GD25T80 0x3114 #define GIGADEVICE_GD25Q512 0x4010 #define GIGADEVICE_GD25Q10 0x4011 #define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25QB */ #define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25QB */ #define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */ #define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */ #define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ #define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ #define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B and GD25Q128C only, can be distinguished by SFDP */ #define GIGADEVICE_GD25VQ21B 0x4212 #define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ #define GIGADEVICE_GD25VQ80C 0x4214 #define GIGADEVICE_GD25VQ16C 0x4215 -#define GIGADEVICE_GD25LQ40 0x6013 -#define GIGADEVICE_GD25LQ80 0x6014 +#define GIGADEVICE_GD25LQ05B 0x6010 +#define GIGADEVICE_GD25LQ10B 0x6011 +#define GIGADEVICE_GD25LQ20B 0x6012 +#define GIGADEVICE_GD25LQ40 0x6013 /* Same as GD25LQ40B, can be distinguished by SFDP */ +#define GIGADEVICE_GD25LQ80 0x6014 /* Same as GD25LQ80B, can be distinguished by SFDP */ #define GIGADEVICE_GD25LQ16 0x6015 #define GIGADEVICE_GD25LQ32 0x6016 #define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */ #define GIGADEVICE_GD25LQ128 0x6018 #define GIGADEVICE_GD29GL064CAB 0x7E0601 #define HYUNDAI_ID 0xAD /* Hyundai */ #define HYUNDAI_HY29F400T 0x23 /* Same as HY29F400AT */ #define HYUNDAI_HY29F800B 0x58 /* Same as HY29F800AB */ #define HYUNDAI_HY29LV800B 0x5B #define HYUNDAI_HY29F040A 0xA4 #define HYUNDAI_HY29F400B 0xAB /* Same as HY29F400AB */ #define HYUNDAI_HY29F002B 0x34 #define HYUNDAI_HY29F002T 0xB0 #define HYUNDAI_HY29LV400T 0xB9 -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 1

[PATCH 0/3] Add support for several GigaDevice SPI chips
by Hatim Kanchwala 16 Mar '16

16 Mar '16

Hello, One of the components I was waiting for was delivered yesterday so I performed tests on some of the sample chips GigaDevice sent using Serprog Arduino flasher (Urja's frser-duino). In the patches that follow, I have added support for 10 chips of which 8 were tested successfully for probe, read, write and erase. A note - level translation using resistors mentioned here (https://www.flashrom.org/Serprog/Arduino_flasher) didn't work for me so I bypassed resistors and connected chip directly to Arduino. Patches follow. Thanks. Hatim Kanchwala (3): Add support for GD25LQ10B, GD25LQ20B, GD25LQ40B and GD25LQ80B Add support for GD25D05B and GD25D10B Add support for GD25Q21B, GD25Q41B, GD25Q80C and GD25Q16C flashchips.c | 397 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 18 +-- 2 files changed, 407 insertions(+), 8 deletions(-) -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

2 8

[PATCH] ft2232_spi: refine error handling in init() and add shutdown function
by Stefan Tauner 16 Mar '16

16 Mar '16

Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- ft2232_spi.c | 84 ++++++++++++++++++++++++++++++++++-------------------------- 1 file changed, 47 insertions(+), 37 deletions(-) Build-tested on the buildbot but not runtime-tested (i still do not own an FT*232 device yet... I can't believe that either :P). diff --git a/ft2232_spi.c b/ft2232_spi.c index be60837..6d388e3 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -101,7 +101,7 @@ const struct dev_entry devs_ft2232spi[] = { */ static uint8_t cs_bits = 0x08; static uint8_t pindir = 0x0b; -static struct ftdi_context ftdic_context; +static struct ftdi_context ftdic_context = {0}; static const char *get_ft2232_devicename(int ft2232_vid, int ft2232_type) { @@ -168,10 +168,19 @@ static const struct spi_master spi_master_ft2232 = { .write_aai = default_spi_write_aai, }; +static int ft2232_spi_shutdown(void *ftdic) { + int ret = ftdi_usb_close(ftdic); + if (ret < 0) { + msg_perr("Unable to close FTDI device: %s (%d)\n", ftdi_get_error_string(ftdic), ret); + } + /* The following will deinit the context and set various of its fields to initial values. */ + ftdi_free(ftdic); + return ret; +} + /* Returns 0 upon success, a negative number upon errors. */ int ft2232_spi_init(void) { - int ret = 0; struct ftdi_context *ftdic = &ftdic_context; unsigned char buf[512]; int ft2232_vid = FTDI_VID; @@ -193,11 +202,8 @@ int ft2232_spi_init(void) * 92 Hz for 12 MHz inputs. */ uint32_t divisor = DEFAULT_DIVISOR; - int f; - char *arg; - double mpsse_clk; - arg = extract_programmer_param("type"); + char *arg = extract_programmer_param("type"); if (arg) { if (!strcasecmp(arg, "2232H")) { ft2232_type = FTDI_FT2232H_PID; @@ -338,22 +344,31 @@ int ft2232_spi_init(void) (ft2232_interface == INTERFACE_B) ? "B" : (ft2232_interface == INTERFACE_C) ? "C" : "D"); - if (ftdi_init(ftdic) < 0) { - msg_perr("ftdi_init failed.\n"); - return -3; + int ret = ftdi_init(ftdic); + if (ret < 0) { + msg_perr("Failed to initialize libftdi driver (%d).\n", ret); + return 1; } - if (ftdi_set_interface(ftdic, ft2232_interface) < 0) { - msg_perr("Unable to select channel (%s).\n", ftdi_get_error_string(ftdic)); + if (register_shutdown(ft2232_spi_shutdown, NULL) != 0) { + return 1; + } + + ret = ftdi_set_interface(ftdic, ft2232_interface); + if (ret < 0) { + msg_perr("Unable to select channel: %s (%d).\n", ftdi_get_error_string(ftdic), ret); + return 1; } arg = extract_programmer_param("serial"); - f = ftdi_usb_open_desc(ftdic, ft2232_vid, ft2232_type, NULL, arg); + int f = ftdi_usb_open_desc(ftdic, ft2232_vid, ft2232_type, NULL, arg); free(arg); + /* -5 is reported in case we cannot claim the respective device. If that's really the case we will abort + * later anywhere. Till then pretend we did not notice... rationale: we always have beed doing it. */ if (f < 0 && f != -5) { - msg_perr("Unable to open FTDI device: %d (%s).\n", f, ftdi_get_error_string(ftdic)); - return -4; + msg_perr("Unable to open FTDI device: %s (%d).\n", ftdi_get_error_string(ftdic), f); + return 1; } if (ftdic->type != TYPE_2232H && ftdic->type != TYPE_4232H && ftdic->type != TYPE_232H) { @@ -362,27 +377,32 @@ int ft2232_spi_init(void) } if (ftdi_usb_reset(ftdic) < 0) { - msg_perr("Unable to reset FTDI device (%s).\n", ftdi_get_error_string(ftdic)); + msg_perr("Unable to reset FTDI device: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } if (ftdi_set_latency_timer(ftdic, 2) < 0) { - msg_perr("Unable to set latency timer (%s).\n", ftdi_get_error_string(ftdic)); + msg_perr("Unable to set latency timer: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } if (ftdi_write_data_set_chunksize(ftdic, 256)) { - msg_perr("Unable to set chunk size (%s).\n", ftdi_get_error_string(ftdic)); + msg_perr("Unable to set chunk size: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } if (ftdi_set_bitmode(ftdic, 0x00, BITMODE_BITBANG_SPI) < 0) { - msg_perr("Unable to set bitmode to SPI (%s).\n", ftdi_get_error_string(ftdic)); + msg_perr("Unable to set bitmode to SPI: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } + double mpsse_clk; if (clock_5x) { msg_pdbg("Disable divide-by-5 front stage\n"); buf[0] = 0x8a; /* Disable divide-by-5. DIS_DIV_5 in newer libftdi */ if (send_buf(ftdic, buf, 1)) { - ret = -5; - goto ftdi_err; + msg_perr("Unable to disable front stage divider: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } mpsse_clk = 60.0; } else { @@ -394,39 +414,29 @@ int ft2232_spi_init(void) buf[1] = (divisor / 2 - 1) & 0xff; buf[2] = ((divisor / 2 - 1) >> 8) & 0xff; if (send_buf(ftdic, buf, 3)) { - ret = -6; - goto ftdi_err; + msg_perr("Unable to set divider: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } msg_pdbg("MPSSE clock: %f MHz, divisor: %u, SPI clock: %f MHz\n", mpsse_clk, divisor, (double)(mpsse_clk / divisor)); /* Disconnect TDI/DO to TDO/DI for loopback. */ - msg_pdbg("No loopback of TDI/DO TDO/DI\n"); buf[0] = LOOPBACK_END; if (send_buf(ftdic, buf, 1)) { - ret = -7; - goto ftdi_err; + msg_perr("Unable to disable TDI/DO TDO/DI loopback: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } - msg_pdbg("Set data bits\n"); buf[0] = SET_BITS_LOW; buf[1] = cs_bits; buf[2] = pindir; if (send_buf(ftdic, buf, 3)) { - ret = -8; - goto ftdi_err; + msg_perr("Unable to set initial pin states: %s.\n", ftdi_get_error_string(ftdic)); + return 1; } - register_spi_master(&spi_master_ft2232); - - return 0; - -ftdi_err: - if ((f = ftdi_usb_close(ftdic)) < 0) { - msg_perr("Unable to close FTDI device: %d (%s)\n", f, ftdi_get_error_string(ftdic)); - } - return ret; + return register_spi_master(&spi_master_ft2232); } /* Returns 0 upon success, a negative number upon errors. */ -- Kind regards, Stefan Tauner

1 0

Re: [flashrom] [coreboot] ft4232-based spi programmer
by Stefan Tauner 16 Mar '16

16 Mar '16

On Thu, 11 Jun 2009 15:00:05 -0400 pgf at foxharp.boston.ma.us (Paul Fox) wrote: > + // f = ftdi_usb_open(ftdic, 0x0403, 0x6010); // FT2232 > + f = ftdi_usb_open(ftdic, 0x0403, 0x6011); // FT4232 > + > + if (f < 0 && f != -5) { > + fprintf(stderr, "unable to open ftdi device: %d (%s)\n", f, > + ftdi_get_error_string(ftdic)); > + exit(-1); > + } Hi, been a while since this went in... however the exemption for the -5 error (failed to claim the device) was never discussed nor documented ever since. Can you remember why you put it there, Paul? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 2

flashrom bug report
by Szőgyényi Gábor 15 Mar '16

15 Mar '16

Hi flashrom.org! Motherboad type: ASUS M4A78LT-M-LEBios Version: 0801 Please read the flashrom output: root@debian:/home/szg# root@debian:/home/szg# root@debian:/home/szg# flashrom -p internal flashrom v0.9.7-r1782 on Linux 3.16.0-4-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.orgCalibrating delay loop... OK. Found chipset "AMD SB7x0/SB8x0/SB9x0". Enabling flash write... OK. Found Eon flash chip "EN25F80" (1024 kB, SPI) at physical address 0xfff00000. Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org No operations were specified. root@debian:/home/szg# root@debian:/home/szg#

2 1

toshiba satellite c660d-144 black screen
by Akram Hossain 15 Mar '16

15 Mar '16

Hi, Can someone help me please with my problem. My Toshiba Satellite C660D-144 has black screen and keyboard lights stays on. I've tried to flash the bios through usb from Toshiba website the exact model bios, but it didn't work. And tired to flash with (USB Programmer CH341A) but nothing is working. Its bricked do I need SPI flash and where I can get the right file. I'm not expert in this case please consider if I write something that doesn't make sense. Please help me. Thanks

1 0

X9DRD-iF
by Pierre Grandin 14 Mar '16

14 Mar '16

flashrom v0.9.6.1-r1563 on Linux 3.13.0-24-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (3 args): flashrom -VV -p internal:laptop=this_is_not_a_laptop Calibrating delay loop... OS timer resolution is 1 usecs, 2494M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 998 us, 10000 myus = 10017 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Supermicro" DMI string system-product-name: "SYS-6017R-TDF" DMI string system-version: "0123456789" DMI string baseboard-manufacturer: "Supermicro" DMI string baseboard-product-name: "X9DRD-iF" DMI string baseboard-version: "REV:1.02" DMI string chassis-type: "Other" DMI chassis-type is not specific enough. ======================================================================== WARNING! You may be running flashrom on an unsupported laptop. We could not detect this for sure because your vendor has not setup the SMBIOS tables correctly. You can enforce execution by adding '-p internal:laptop=this_is_not_a_laptop' to the command line, but please read the following warning if you are not sure. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Proceeding anyway because user forced us to. Found chipset "Intel X79" with PCI ID 8086:1d41. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2a WARNING: BIOS region SMM protection is enabled! Root Complex Register Block address = 0xfed1c000 GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6018 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=3, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x000f0000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x0000ffff) is read-only. 0x58: 0x0fff0400 FREG1: BIOS region (0x00400000-0x00ffffff) is read-write. 0x5C: 0x03ff0020 FREG2: WARNING: Management Engine region (0x00020000-0x003fffff) is locked. 0x60: 0x00000fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x001f0010 FREG4: Platform Data region (0x00010000-0x0001ffff) is read-write. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf84140 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=4, DBC=1, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x0000d807 (LVSCC) LVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8, VCL=0 0xC8: 0x0000d807 (UVSCC) UVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040003 FLMAP1 0x12100206 FLMAP2 0x00210020 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 0 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x24900025 FLILL 0x00000000 --- Details --- Component 1 density: 16 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 50 MHz Write and Erase Clock Freq.: 50 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz No forbidden opcodes. === Region Section === FLREG0 0x000f0000 FLREG1 0x0fff0400 FLREG2 0x03ff0020 FLREG3 0x00000fff FLREG4 0x001f0010 --- Details --- Region 0 (Descr.) 0x00000000 - 0x0000ffff Region 1 (BIOS ) 0x00400000 - 0x00ffffff Region 2 (ME ) 0x00020000 - 0x003fffff Region 3 (GbE ) is unused. Region 4 (Platf.) 0x00010000 - 0x0001ffff === Master Section === FLMSTR1 0x1a1b0000 FLMSTR2 0x04050000 FLMSTR3 0x08090118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw rw ME r rw GbE r rw SPI Read Configuration: prefetching enabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 SFDP revision = 1.0 SFDP number of parameter headers is 1 (NPH = 0). SFDP parameter table header 0/0: ID 0x00, version 1.0 Length 36 B, Parameter Table Pointer 0x000030 Parsing JEDEC flash parameter table... 3-Byte only addressing. Status register is non-volatile and the standard does not allow vendors to tell us whether EWSR/WREN is needed for status register writes - assuming EWSR. Write chunk size is at least 64 B. Flash chip size is 16384 kB. Block eraser 0: 4096 x 4096 B with opcode 0x20 Tried to add a duplicate block eraser: 4096 x 4096 B with opcode 0x20. Block eraser 1: 256 x 65536 B with opcode 0xd8 done. === SFDP has autodetected a flash chip which is not natively supported by flashrom yet. All standard operations (read, verify, erase and write) should work, but to support all possible features we need to add them manually. You can help us by mailing us the output of the following command to flashrom(a)flashrom.org: 'flashrom -VV [plus the -p/--programmer parameter (if needed)]' Thanks for your help! === Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI) at physical address 0x0. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI). No operations were specified. Restoring MMIO space at 0x7f258db388a0 Restoring MMIO space at 0x7f258db3889c Restoring MMIO space at 0x7f258db38898 Restoring MMIO space at 0x7f258db38896 Restoring MMIO space at 0x7f258db38894 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

W25X64 tested and works with beaglebone black for lenovo x200.
by Andrew Engelbrecht 14 Mar '16

14 Mar '16

i wasn't using the newest version of flashrom, but in case you don't have this chip marked as tested in the newest version, here is the output for reading and writing this chip: andrew > root@beaglebone:~# ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -r x200-0-bios-orig-1.rom > flashrom v0.9.8-unknown on Linux 3.8.13 (armv7l) > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > Found Winbond flash chip "W25X64" (8192 kB, SPI) on linux_spi. > === > This flash part has status UNTESTED for operations: READ ERASE WRITE > The test status of this chip may have been updated in the latest development > version of flashrom. If you are running the latest development version, > please email a report to flashrom(a)flashrom.org if any of the above operations > work correctly for you with this flash chip. Please include the flashrom log > file for all operations you tested (see the man page for details), and mention > which mainboard or programmer you tested in the subject line. > Thanks for your help! > Reading flash... done. > > root@beaglebone:~/libreboot# ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -w x200-8mb-libreboot.rom > flashrom v0.9.8-unknown on Linux 3.8.13 (armv7l) > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > Found Winbond flash chip "W25X64" (8192 kB, SPI) on linux_spi. > === > This flash part has status UNTESTED for operations: READ ERASE WRITE > The test status of this chip may have been updated in the latest development > version of flashrom. If you are running the latest development version, > please email a report to flashrom(a)flashrom.org if any of the above operations > work correctly for you with this flash chip. Please include the flashrom log > file for all operations you tested (see the man page for details), and mention > which mainboard or programmer you tested in the subject line. > Thanks for your help! > Reading old flash chip contents... done. > Erasing and writing flash chip... Erase/write done. > Verifying flash... VERIFIED.

1 0

[commit] r1955 - tags/0.9.9
by repository service 13 Mar '16

13 Mar '16

Author: stefanct Date: Sun Mar 13 18:47:39 2016 New Revision: 1955 URL: http://flashrom.org/trac/flashrom/changeset/1955 Log: Tag flashrom 0.9.9. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Urja Rannikko <urjaman(a)gmail.com> Added: tags/0.9.9/ - copied from r1954, trunk/

1 0

[commit] r1954 - trunk
by repository service 13 Mar '16

13 Mar '16

Author: stefanct Date: Sun Mar 13 18:46:08 2016 New Revision: 1954 URL: http://flashrom.org/trac/flashrom/changeset/1954 Log: Increase flashrom version number to 0.9.9. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Urja Rannikko <urjaman(a)gmail.com> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sun Mar 13 18:36:49 2016 (r1953) +++ trunk/Makefile Sun Mar 13 18:46:08 2016 (r1954) @@ -531,7 +531,7 @@ # will not require subversion. The downloadable snapshots are already exported. SVNVERSION := $(shell ./util/getrevision.sh -u 2>/dev/null ) -RELEASE := 0.9.9-rc1 +RELEASE := 0.9.9 VERSION := $(RELEASE)-$(SVNVERSION) RELEASENAME ?= $(VERSION)

1 0

[Security Announcement] fscanf format string security bug in flashrom layout code
by Carl-Daniel Hailfinger 13 Mar '16

13 Mar '16

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 NotDashEscaped: You need GnuPG to verify this message An internal security audit of the flashrom project by Carl-Daniel Hailfinger found a buffer overflow bug present in all flashrom versions since the year 2005. This bug was independently found and reported to flashrom.org by Cosmin Gorgovan a few days ago. A buffer on the stack and a buffer on the heap are affected by the overflow caused by an incorrect fscanf format string. The buffer overflow can only be triggered if the optional layout feature is used and if the user manually specifies a specially crafted layout file on the command line. Command line parsing and flash image handling do not trigger the buggy code path. Most usage of flashrom does not involve layout files. The fix in this commit (changed fscanf format string) can be applied to layout.c of all past flashrom versions. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Index: flashrom-parserbugs_simple/layout.c =================================================================== --- flashrom-parserbugs_simple/layout.c (revision 1952) +++ flashrom-parserbugs_simple/layout.c (working copy) @@ -68,7 +68,7 @@ (void)fclose(romlayout); return 1; } - if (2 != fscanf(romlayout, "%s %s\n", tempstr, rom_entries[num_rom_entries].name)) + if (2 != fscanf(romlayout, "%255s %255s\n", tempstr, rom_entries[num_rom_entries].name)) continue; #if 0 // fscanf does not like arbitrary comments like that :( later -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iD8DBQFW5aNeRdNMz2eF/AERAootAJ4q5RtwHTXk7nSPu/1usG3y3pnVPACgzBbQ uxn/opeqC3Kh2F1PE2lVcUU= =z/7t -----END PGP SIGNATURE-----

1 1

[commit] r1953 - trunk
by repository service 13 Mar '16

13 Mar '16

Author: hailfinger Date: Sun Mar 13 18:36:49 2016 New Revision: 1953 URL: http://flashrom.org/trac/flashrom/changeset/1953 Log: Fix fscanf format string security bug in layout.c An internal security audit of the flashrom project by Carl-Daniel Hailfinger found a buffer overflow bug present in all flashrom versions since the year 2005. This bug was independently found and reported to flashrom.org by Cosmin Gorgovan a few days ago. A buffer on the stack and a buffer on the heap are affected by the overflow caused by an incorrect fscanf format string. The buffer overflow can only be triggered if the optional layout feature is used and if the user manually specifies a specially crafted layout file on the command line. Command line parsing and flash image handling do not trigger the buggy code path. Most usage of flashrom does not involve layout files. The fix in this commit (changed fscanf format string) can be applied to layout.c of all past flashrom versions. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/layout.c Modified: trunk/layout.c ============================================================================== --- trunk/layout.c Sun Mar 13 17:24:09 2016 (r1952) +++ trunk/layout.c Sun Mar 13 18:36:49 2016 (r1953) @@ -68,7 +68,7 @@ (void)fclose(romlayout); return 1; } - if (2 != fscanf(romlayout, "%s %s\n", tempstr, rom_entries[num_rom_entries].name)) + if (2 != fscanf(romlayout, "%255s %255s\n", tempstr, rom_entries[num_rom_entries].name)) continue; #if 0 // fscanf does not like arbitrary comments like that :( later

1 0

[PATCH] Shutdown serial port in pony_spi
by Carl-Daniel Hailfinger 13 Mar '16

13 Mar '16

Implement serial port shutdown both for regular termination and error condition in pony_spi. [Yes, the existing code is not exactly beautiful, but a rewrite shortly before 0.9.9 is too risky.] Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-pony_close_fd/pony_spi.c =================================================================== --- flashrom-pony_close_fd/pony_spi.c (Revision 1946) +++ flashrom-pony_close_fd/pony_spi.c (Arbeitskopie) @@ -103,6 +103,20 @@ .half_period = 0, }; +static int pony_spi_shutdown(void *data) +{ + int ret = 0; + + /* Shut down serial port communication */ + ret = serialport_shutdown(NULL); + if (ret) + msg_pdbg("Pony SPI shutdown failed.\n"); + else + msg_pdbg("Pony SPI shutdown completed.\n"); + + return ret; +} + int pony_spi_init(void) { int i, data_out; @@ -120,6 +134,11 @@ free(arg); return 1; } + if (register_shutdown(pony_spi_shutdown, NULL) != 0) { + free(arg); + serialport_shutdown(NULL); + return 1; + } have_device++; } free(arg);

1 2

[commit] r1952 - trunk
by repository service 13 Mar '16

13 Mar '16

Author: hailfinger Date: Sun Mar 13 17:24:09 2016 New Revision: 1952 URL: http://flashrom.org/trac/flashrom/changeset/1952 Log: Implement serial port shutdown both for regular termination and error condition in pony_spi. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/pony_spi.c Modified: trunk/pony_spi.c ============================================================================== --- trunk/pony_spi.c Sun Mar 13 16:16:30 2016 (r1951) +++ trunk/pony_spi.c Sun Mar 13 17:24:09 2016 (r1952) @@ -103,6 +103,18 @@ .half_period = 0, }; +static int pony_spi_shutdown(void *data) +{ + /* Shut down serial port communication */ + int ret = serialport_shutdown(NULL); + if (ret) + msg_pdbg("Pony SPI shutdown failed.\n"); + else + msg_pdbg("Pony SPI shutdown completed.\n"); + + return ret; +} + int pony_spi_init(void) { int i, data_out; @@ -120,6 +132,11 @@ free(arg); return 1; } + if (register_shutdown(pony_spi_shutdown, NULL) != 0) { + free(arg); + serialport_shutdown(NULL); + return 1; + } have_device++; } free(arg);

1 0

Re: [flashrom] [PATCH] Add a bunch of new/tested stuff and various small changes 25.
by Carl-Daniel Hailfinger 13 Mar '16

13 Mar '16

On 05.03.2016 22:42, Stefan Tauner wrote: > Tested mainboards: > OK: > - ASRock Fatal1ty 970 Performance and P4i65G > Reported by anonymous email message ID: > 932677687262b1300eaf14260999d9262c31(a)guerrillamail.com > The latter actually had a tested board enable already. > > Flash chips: > - GigaDevice GD25VQ41B to PREW (+PREW) > Reported by David Hendricks > - Winbond W39V040FB to PREW (+EW) > Reported by fjed on IRC > > Miscellaneous: > - Change PCI IDs of "MS-6577 (Xenon)" board enable. > The previous IDs contained the on-board display adapter which is > disabled when a dedicated graphics card is installed. > - Add a note to the README how to overcome the clang warning if only a > single programmer is enabled. > - Fix some typo and manpage problems found by lintian > - r1920 introduced some explicit calls to pkg-config instead of $(PKG_CONFIG). > This patch corrects that. > - Add some overrides to the Makefile in case someone/something sets > variables like CPPFLAGS or LDFLAGS as command line parameters I couldn't find that in the patch. > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > --- > Makefile | 34 ++++++++++++++--------------- > README | 6 ++++++ > board_enable.c | 2 +- > flashchips.c | 66 ++++++++++++++++++++++++++++----------------------------- > flashrom.8.tmpl | 38 ++++++++++++++++++--------------- > pickit2_spi.c | 2 +- > print.c | 4 ++-- > sb600spi.c | 2 +- > 8 files changed, 82 insertions(+), 72 deletions(-) > > diff --git a/Makefile b/Makefile > index 927105d..d9a70b3 100644 > --- a/Makefile > +++ b/Makefile > @@ -661,22 +661,22 @@ override CONFIG_CH341A_SPI = no > override CONFIG_DEDIPROG = no > endif > ifeq ($(CONFIG_ENABLE_LIBPCI_PROGRAMMERS), no) > -override CONFIG_INTERNAL = no > -override CONFIG_NIC3COM = no > -override CONFIG_GFXNVIDIA = no > -override CONFIG_SATASII = no > -override CONFIG_ATAHPT = no > -override CONFIG_ATAVIA = no > -override CONFIG_ATAPROMISE = no > -override CONFIG_IT8212 = no > -override CONFIG_DRKAISER = no > -override CONFIG_NICREALTEK = no > -override CONFIG_NICNATSEMI = no > -override CONFIG_NICINTEL = no > -override CONFIG_NICINTEL_SPI = no > -override CONFIG_NICINTEL_EEPROM = no > -override CONFIG_OGP_SPI = no > -override CONFIG_SATAMV = no > +override CONFIG_INTERNAL = no > +override CONFIG_NIC3COM = no > +override CONFIG_GFXNVIDIA = no > +override CONFIG_SATASII = no > +override CONFIG_ATAHPT = no > +override CONFIG_ATAVIA = no > +override CONFIG_ATAPROMISE = no > +override CONFIG_IT8212 = no > +override CONFIG_DRKAISER = no > +override CONFIG_NICREALTEK = no > +override CONFIG_NICNATSEMI = no > +override CONFIG_NICINTEL = no > +override CONFIG_NICINTEL_SPI = no > +override CONFIG_NICINTEL_EEPROM = no > +override CONFIG_OGP_SPI = no > +override CONFIG_SATAMV = no Zero changes except whitespace. The changelog claims the overrides changed. > endif > > # Bitbanging SPI infrastructure, default off unless needed. > diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl > index cb77e46..5de735b 100644 > --- a/flashrom.8.tmpl > +++ b/flashrom.8.tmpl > @@ -1,9 +1,11 @@ > .\" Load the www device when using groff; provide a fallback for groff's MTO macro that formats email addresses. > .ie \n[.g] \ > . mso www.tmac > -.el \ > -. de MTO \\$2 \(la\\$1 \(ra\\$3 > +.el \{ > +. de MTO > + \\$2 \(la\\$1 \(ra\\$3 \ > . . > +.\} > .\" Create wrappers for .MTO and .URL that print only text on systems w/o groff or if not outputting to a HTML > .\" device. To that end we need to distinguish HTML output on groff from other configurations first. > .nr groffhtml 0 I have to trust you on this. > @@ -684,13 +680,18 @@ size (padding to 32 kB is required). > .IP > This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs > mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their > -size nor allow to be identified, the controller relies on correct size values written to predefined addresses > -within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed > -EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST) > -M95128, M95256 and OnSemi (Catalyst) CAT25CS128. > +size nor allow themselves to be identified, the controller relies on correct size values written to predefined > +addresses within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an > +unprogrammed EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: > +Atmel AT25128, AT25256, Micron (ST) M95128, M95256 and OnSemi (Catalyst) CAT25CS128. Sorry, -ENOPARSE. Does this mean we try to determine chip size by reading predefined locations of the EEPROM where size is customarily stored? > .SS > .BR "ft2232_spi " programmer > .IP > +This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design > +DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, > +Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB > +Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2. > +.sp > An optional parameter specifies the controller > type and channel/interface/port it should support. For that you have to use the > .sp > @@ -981,7 +985,7 @@ Please note that the linux_spi driver only works on Linux. > .BR "mstarddc_spi " programmer > .IP > The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging > -informations between a computer and attached displays. Its most common uses are getting display capabilities > +information between a computer and attached displays. Its most common uses are getting display capabilities > through EDID (at I2C address 0x50) and sending commands to the display using the DDC/CI protocol (at address > 0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC firmware flash (connected to > the Soc through another SPI bus) using an In-System Programming (ISP) port, usually at address 0x49. > @@ -1016,7 +1020,7 @@ Example that does not reset the display at the end of the operation: > .sp > .B " flashrom \-p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1 > .sp > -Please note that sending the reset command is also inhibited in the event an error occured during the operation. > +Please note that sending the reset command is also inhibited in the event an error occurred during the operation. Please note that sending the reset command is also inhibited if an error occurred during the operation. > To send the reset command afterwards, you can simply run flashrom once more, in chip probe mode (not specifying > an operation), without the > .B noreset > diff --git a/pickit2_spi.c b/pickit2_spi.c > index f1f60a2..f6aa676 100644 > --- a/pickit2_spi.c > +++ b/pickit2_spi.c > @@ -400,7 +400,7 @@ static int pickit2_shutdown(void *data) > > int pickit2_spi_init(void) > { > - unsigned int usedevice = 0; // FIXME: allow to select one of multiple devices > + unsigned int usedevice = 0; // FIXME: allows one to select one of multiple devices The original sentence has grammar problems, but I wouldn't endorse the replacement either. "Allow selecting one of multiple devices" would have correct grammar and style. Regards, Carl-Daniel

2 3

[commit] r1951 - in trunk: . util/ich_descriptors_tool
by repository service 13 Mar '16

13 Mar '16

Author: stefanct Date: Sun Mar 13 16:16:30 2016 New Revision: 1951 URL: http://flashrom.org/trac/flashrom/changeset/1951 Log: Add a bunch of new/tested stuff and various small changes 25. Tested mainboards: OK: - ASRock Fatal1ty 970 Performance and P4i65G Reported by anonymous email message ID: 932677687262b1300eaf14260999d9262c31(a)guerrillamail.com The latter actually had a tested board enable already. Flash chips: - Eon EN25Q128 to PREW (+PREW) Reported by Adrian Graham - GigaDevice GD25VQ41B to PREW (+PREW) Reported by David Hendricks - Winbond W39V040FB to PREW (+EW) Reported by fjed on IRC Miscellaneous: - Change PCI IDs of "MS-6577 (Xenon)" board enable. The previous IDs contained the on-board display adapter which is disabled when a dedicated graphics card is installed. - Add a note to the README how to overcome the clang warning if only a single programmer is enabled. - Fix some typo and manpage problems found by lintian - r1920 introduced some explicit calls to pkg-config instead of $(PKG_CONFIG). This patch corrects that. - Make MS-7094 (K8T Neo2-F V2.0) board enable less contestable. Previous PCI IDs were board-specific but ot the other of devices that could be disabled by the firmware or that vary among hardware revions. There are no good alternatives available. However, since we always have a DMI decoder available now, we can use non-board-specific devices without taking risks. Thanks to Uwe Hermann for reporting and testing. - Some other small changes to clean up whitespace and fix some warnings from Debian's lintian. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile trunk/README trunk/board_enable.c trunk/flashchips.c trunk/flashrom.8.tmpl trunk/pickit2_spi.c trunk/print.c trunk/sb600spi.c trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/Makefile Sun Mar 13 16:16:30 2016 (r1951) @@ -314,7 +314,7 @@ else override CONFIG_PONY_SPI = no endif -# Dediprog, USB-Blaster, PICkit2, CH341A and FT2232 are not supported with libpayload (missing libusb support) +# Dediprog, USB-Blaster, PICkit2, CH341A and FT2232 are not supported with libpayload (missing libusb support). ifeq ($(CONFIG_DEDIPROG), yes) UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes else @@ -661,22 +661,22 @@ override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_ENABLE_LIBPCI_PROGRAMMERS), no) -override CONFIG_INTERNAL = no -override CONFIG_NIC3COM = no -override CONFIG_GFXNVIDIA = no -override CONFIG_SATASII = no -override CONFIG_ATAHPT = no -override CONFIG_ATAVIA = no -override CONFIG_ATAPROMISE = no -override CONFIG_IT8212 = no -override CONFIG_DRKAISER = no -override CONFIG_NICREALTEK = no -override CONFIG_NICNATSEMI = no -override CONFIG_NICINTEL = no -override CONFIG_NICINTEL_SPI = no -override CONFIG_NICINTEL_EEPROM = no -override CONFIG_OGP_SPI = no -override CONFIG_SATAMV = no +override CONFIG_INTERNAL = no +override CONFIG_NIC3COM = no +override CONFIG_GFXNVIDIA = no +override CONFIG_SATASII = no +override CONFIG_ATAHPT = no +override CONFIG_ATAVIA = no +override CONFIG_ATAPROMISE = no +override CONFIG_IT8212 = no +override CONFIG_DRKAISER = no +override CONFIG_NICREALTEK = no +override CONFIG_NICNATSEMI = no +override CONFIG_NICINTEL = no +override CONFIG_NICINTEL_SPI = no +override CONFIG_NICINTEL_EEPROM = no +override CONFIG_OGP_SPI = no +override CONFIG_SATAMV = no endif # Bitbanging SPI infrastructure, default off unless needed. Modified: trunk/README ============================================================================== --- trunk/README Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/README Sun Mar 13 16:16:30 2016 (r1951) @@ -136,6 +136,12 @@ use port-based I/O which is not directly available on non-x86. Those programmers will be disabled automatically if you run "make". +Compiler quirks: + +If you are using clang and if you want to enable only one driver, you may hit an +overzealous compiler warning from clang. Compile with "make WARNERROR=no" to +force it to continue and enjoy. + Installation ------------ Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/board_enable.c Sun Mar 13 16:16:30 2016 (r1951) @@ -2440,9 +2440,9 @@ {0x8086, 0x7190, 0, 0, 0x8086, 0x7110, 0, 0, "^MS-6163 (i440BX)$", NULL, NULL, P3, "MSI", "MS-6163 (MS-6163 Pro)", 0, OK, intel_piix4_gpo14_raise}, {0x8086, 0x244b, 0x1462, 0x3910, 0x8086, 0x2442, 0x1462, 0x3910, NULL, NULL, NULL, P3, "MSI", "MS-6391 (845 Pro4)", 0, OK, intel_ich_gpio23_raise}, {0x1039, 0x0745, 0, 0, 0x1039, 0x0018, 0, 0, "^MS-6561", NULL, NULL, P3, "MSI", "MS-6561 (745 Ultra)", 0, OK, w836xx_memw_enable_2e}, - {0x8086, 0x2560, 0x1462, 0x5770, 0x8086, 0x2562, 0x1462, 0x5778, NULL, NULL, NULL, P3, "MSI", "MS-6577 (Xenon)", 0, OK, w83627hf_gpio25_raise_2e}, + {0x8086, 0x2560, 0x1462, 0x5770, 0x8086, 0x24C3, 0x1462, 0x5770, NULL, NULL, NULL, P3, "MSI", "MS-6577 (Xenon)", 0, OK, w83627hf_gpio25_raise_2e}, {0x13f6, 0x0111, 0x1462, 0x5900, 0x1106, 0x3177, 0x1106, 0, NULL, NULL, NULL, P3, "MSI", "MS-6590 (KT4 Ultra)", 0, OK, board_msi_kt4v}, - {0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, "^MS-7094$", NULL, NULL, P3, "MSI", "MS-7094 (K8T Neo2-F V2.0)", 0, OK, w83627thf_gpio44_raise_2e}, + {0x1106, 0x0282, 0x1106, 0x0282, 0x1106, 0x3227, 0x1106, 0x3227, "^MS-7094$", NULL, NULL, P3, "MSI", "MS-7094 (K8T Neo2-F V2.0)", 0, OK, w83627thf_gpio44_raise_2e}, {0x1106, 0x0571, 0x1462, 0x7120, 0x1106, 0x3065, 0x1462, 0x7120, NULL, NULL, NULL, P3, "MSI", "MS-6712 (KT4V)", 0, OK, board_msi_kt4v}, {0x1106, 0x3148, 0 , 0 , 0x1106, 0x3177, 0 , 0 , NULL, "msi", "ms6787", P3, "MSI", "MS-6787 (P4MAM-V/P4MAM-L)", 0, OK, w836xx_memw_enable_2e}, {0x8086, 0x24d3, 0x1462, 0x7880, 0x8086, 0x2570, 0, 0, NULL, NULL, NULL, P3, "MSI", "MS-6788-040 (848P NeoV)", 0, OK, intel_ich_gpio32_raise}, Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/flashchips.c Sun Mar 13 16:16:30 2016 (r1951) @@ -4663,7 +4663,7 @@ .page_size = 256, /* OTP: 512B total; enter 0x3A */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -5368,13 +5368,13 @@ .probe_timing = TIMING_ZERO, .block_erasers = { - { - .eraseblocks = { {64 * 1024, 8} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { {64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, .printlock = spi_prettyprint_status_register_bp2_srwd, .unlock = spi_disable_blockprotect_bp2_srwd, @@ -5399,13 +5399,13 @@ .probe_timing = TIMING_ZERO, .block_erasers = { - { - .eraseblocks = { {64 * 1024, 16} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { {64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, .printlock = spi_prettyprint_status_register_bp2_srwd, .unlock = spi_disable_blockprotect_bp2_srwd, @@ -6382,27 +6382,27 @@ .page_size = 256, /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, - .block_erasers = + .block_erasers = { - { - .eraseblocks = { { 4 * 1024, 128} }, - .block_erase = spi_block_erase_20, - }, { - .eraseblocks = { { 32 * 1024, 16} }, - .block_erase = spi_block_erase_52, - }, { - .eraseblocks = { { 64 * 1024, 8} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_60, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { { 4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ @@ -15627,7 +15627,7 @@ .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_jedec, .probe_timing = 10, .block_erasers = Modified: trunk/flashrom.8.tmpl ============================================================================== --- trunk/flashrom.8.tmpl Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/flashrom.8.tmpl Sun Mar 13 16:16:30 2016 (r1951) @@ -1,9 +1,11 @@ .\" Load the www device when using groff; provide a fallback for groff's MTO macro that formats email addresses. .ie \n[.g] \ . mso www.tmac -.el \ -. de MTO \\$2 \(la\\$1 \(ra\\$3 +.el \{ +. de MTO + \\$2 \(la\\$1 \(ra\\$3 \ . . +.\} .\" Create wrappers for .MTO and .URL that print only text on systems w/o groff or if not outputting to a HTML .\" device. To that end we need to distinguish HTML output on groff from other configurations first. .nr groffhtml 0 @@ -208,7 +210,7 @@ Specify the programmer device. This is mandatory for all operations involving any chip access (probe/read/write/...). Currently supported are: .sp -.BR "* internal" " (default, for in-system flashing in the mainboard)" +.BR "* internal" " (for in-system flashing in the mainboard)" .sp .BR "* dummy" " (virtual programmer for testing flashrom)" .sp @@ -237,16 +239,10 @@ .sp .BR "* it8212" " (for flash ROMs on ITE IT8212F ATA/RAID controller)" .sp -.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family \ -based USB SPI programmer), including the DLP Design DLP-USB1232H, \ -FTDI FT2232H Mini-Module, FTDI FT4232H Mini-Module, openbiosprog-spi, Amontec \ -JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, \ -Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, TIAO/DIYGADGET USB -Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2. +.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family based USB SPI programmer). .sp .BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog, \ -including Arduino-based devices as well as various programmers by Urja Rannikko, \ -Juhana Helovuo, Stefan Tauner and others)." +including some Arduino-based devices)." .sp .BR "* buspirate_spi" " (for SPI flash ROMs attached to a Bus Pirate)" .sp @@ -684,13 +680,18 @@ .IP This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their -size nor allow to be identified, the controller relies on correct size values written to predefined addresses -within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed -EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST) -M95128, M95256 and OnSemi (Catalyst) CAT25CS128. +size nor allow themselves to be identified, the controller relies on correct size values written to predefined +addresses within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an +unprogrammed EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: +Atmel AT25128, AT25256, Micron (ST) M95128, M95256 and OnSemi (Catalyst) CAT25CS128. .SS .BR "ft2232_spi " programmer .IP +This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design +DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, +Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB +Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2. +.sp An optional parameter specifies the controller type and channel/interface/port it should support. For that you have to use the .sp @@ -736,6 +737,9 @@ .SS .BR "serprog " programmer .IP +This module supports all programmers speaking the serprog protocol. This includes some Arduino-based devices +as well as various programmers by Urja Rannikko, Juhana Helovuo, Stefan Tauner, Chi Zhang and many others. +.sp A mandatory parameter specifies either a serial device (and baud rate) or an IP/port combination for communicating with the programmer. The device/baud combination has to start with @@ -981,7 +985,7 @@ .BR "mstarddc_spi " programmer .IP The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging -informations between a computer and attached displays. Its most common uses are getting display capabilities +information between a computer and attached displays. Its most common uses are getting display capabilities through EDID (at I2C address 0x50) and sending commands to the display using the DDC/CI protocol (at address 0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC firmware flash (connected to the Soc through another SPI bus) using an In-System Programming (ISP) port, usually at address 0x49. @@ -1016,7 +1020,7 @@ .sp .B " flashrom \-p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1 .sp -Please note that sending the reset command is also inhibited in the event an error occured during the operation. +Please note that sending the reset command is also inhibited if an error occurred during the operation. To send the reset command afterwards, you can simply run flashrom once more, in chip probe mode (not specifying an operation), without the .B noreset Modified: trunk/pickit2_spi.c ============================================================================== --- trunk/pickit2_spi.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/pickit2_spi.c Sun Mar 13 16:16:30 2016 (r1951) @@ -400,7 +400,7 @@ int pickit2_spi_init(void) { - unsigned int usedevice = 0; // FIXME: allow to select one of multiple devices + unsigned int usedevice = 0; // FIXME: Allow selecting one of multiple devices uint8_t buf[CMD_LENGTH] = { CMD_EXEC_SCRIPT, Modified: trunk/print.c ============================================================================== --- trunk/print.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/print.c Sun Mar 13 16:16:30 2016 (r1951) @@ -490,11 +490,9 @@ case USB: print_supported_devs(prog, "USB"); break; -#if NEED_PCI == 1 case PCI: print_supported_devs(prog, "PCI"); break; -#endif case OTHER: if (prog.devs.note != NULL) { msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); @@ -571,6 +569,7 @@ B("ASRock", "AMCP7AION-HT", OK, "http://www.asrock.com/nettop/NVIDIA/ION%20330HT/", "Used in ION 330HT(-BD) barebones."), B("ASRock", "ConRoeXFire-eSATA2", OK, "http://www.asrock.com/mb/overview.asp?model=conroexfire-esata2", NULL), B("ASRock", "E350M1/USB3", OK, "http://www.asrock.com/mb/overview.asp?model=e350m1/usb3", "Vendor firmware writes to flash at shutdown. This probably corrupts the flash in case you write coreboot while running the vendor firmware. Simply updating the vendor firmware should be fine."), + B("ASRock", "Fatal1ty 970 Performance", OK, "http://www.asrock.com/mb/overview.asp?Model=Fatal1ty%20970%20Performance", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "Fatal1ty Z77 Performance", BAD, "http://www.asrock.com/mb/overview.asp?Model=Fatal1ty%20Z77%20Performance", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "G31M-GS", OK, "http://www.asrock.com/mb/overview.asp?Model=G31M-GS", NULL), B("ASRock", "G31M-S rev 2.0", OK, "http://www.asrock.com/mb/overview.asp?model=G31M-S", NULL), @@ -585,6 +584,7 @@ B("ASRock", "M3A790GXH/128M", OK, "http://www.asrock.com/mb/overview.asp?Model=M3A790GXH/128M", NULL), B("ASRock", "N61P-S", OK, "http://www.asrock.com/mb/overview.asp?Model=N61P-S", NULL), B("ASRock", "N68C-S UCC", OK, "http://www.asrock.com/mb/overview.asp?Model=N68C-S%20UCC", NULL), + B("ASRock", "P4i65G", OK, "http://www.asrock.com/mb/overview.asp?Model=P4i65G", NULL), B("ASRock", "P4i65GV", OK, "http://www.asrock.com/mb/overview.asp?Model=P4i65GV", NULL), B("ASRock", "Z68 Extreme4", BAD, "http://www.asrock.com/mb/overview.asp?Model=Z68%20Extreme4", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "A7N8X Deluxe", OK, "http://www.asus.com/Motherboards/AMD_Socket_A/A7N8X_Deluxe/", NULL), Modified: trunk/sb600spi.c ============================================================================== --- trunk/sb600spi.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/sb600spi.c Sun Mar 13 16:16:30 2016 (r1951) @@ -512,7 +512,7 @@ msg_pinfo("Writes have been disabled for safety reasons because the presence of the IMC\n" "was detected and it could interfere with accessing flash memory. Flashrom will\n" "try to disable it temporarily but even then this might not be safe:\n" - "when it is reenabled and after a reboot it expects to find working code\n" + "when it is re-enabled and after a reboot it expects to find working code\n" "in the flash and it is unpredictable what happens if there is none.\n" "\n" "To be safe make sure that there is a working IMC firmware at the right\n" Modified: trunk/util/ich_descriptors_tool/ich_descriptors_tool.c ============================================================================== --- trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Sun Mar 13 13:57:03 2016 (r1950) +++ trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Sun Mar 13 16:16:30 2016 (r1951) @@ -180,7 +180,7 @@ usage(argv, "Could not allocate memory"); lseek(fd, 0, SEEK_SET); if (len != read(fd, buf, len)) - usage(argv, "Seeking to the end of the file failed"); + usage(argv, "Reading the descriptor image file failed"); } printf("The flash image has a size of %d [0x%x] bytes.\n", len, len); close(fd);

1 0

Re: [flashrom] [PATCH] Fix compilation on SunOS.
by Carl-Daniel Hailfinger 13 Mar '16

13 Mar '16

On 13.03.2016 00:05, Stefan Tauner wrote: > This came up when I was testing if building on SunOS still works > on the buildbot's instance of OmniOS r151014 which is based on illumos. > > The fix is > - to link against libnsl > - a small C type fix in ich_descriptor_tool > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > > diff --git a/util/ich_descriptors_tool/ich_descriptors_tool.c b/util/ich_descriptors_tool/ich_descriptors_tool.c > index c3d9ba1..ad3b6f0 100644 > --- a/util/ich_descriptors_tool/ich_descriptors_tool.c > +++ b/util/ich_descriptors_tool/ich_descriptors_tool.c > @@ -170,7 +170,7 @@ int main(int argc, char *argv[]) > usage(argv, "Seeking to the end of the file failed"); > > #ifdef HAVE_MMAP > - buf = mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); > + buf = (uint32_t *)mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); The compiler may require that to stop complaining, but AFAICS there is a real bug behind this. buf is sometimes casted to uint8_t *, and unless I'm too sleepy already, this buffer violates the strict aliasing rules. We can solve this with -fno-strict-aliasing, or fix the code. With a code fix, in theory the problem should go away. > if (buf == (void *) -1) > #endif > { Side note (no need to fix this right now) util/ich_descriptors_tool/ich_descriptors_tool.c:182 if (len != read(fd, buf, len)) usage(argv, "Seeking to the end of the file failed"); Somehow that error message doesn't fit with the code. Regards, Carl-Daniel

2 3

[commit] r1950 - in trunk: . util/ich_descriptors_tool
by repository service 13 Mar '16

13 Mar '16

Author: stefanct Date: Sun Mar 13 13:57:03 2016 New Revision: 1950 URL: http://flashrom.org/trac/flashrom/changeset/1950 Log: Fix compilation on SunOS. This came up when I was testing if building on SunOS still works on the buildbot's instance of OmniOS r151014 which is based on illumos. The fix is - to link against libnsl - a small C type fix in ich_descriptor_tool Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sat Mar 12 20:49:14 2016 (r1949) +++ trunk/Makefile Sun Mar 13 13:57:03 2016 (r1950) @@ -926,7 +926,7 @@ ifneq ($(NEED_POSIX_SOCKETS), ) ifeq ($(TARGET_OS), SunOS) -LIBS += -lsocket +LIBS += -lsocket -lnsl endif endif Modified: trunk/util/ich_descriptors_tool/ich_descriptors_tool.c ============================================================================== --- trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Sat Mar 12 20:49:14 2016 (r1949) +++ trunk/util/ich_descriptors_tool/ich_descriptors_tool.c Sun Mar 13 13:57:03 2016 (r1950) @@ -170,7 +170,7 @@ usage(argv, "Seeking to the end of the file failed"); #ifdef HAVE_MMAP - buf = mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); + buf = (uint32_t *)mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); if (buf == (void *) -1) #endif {

1 0

PATCH: whitelist for ThinkPad T500 and R400
by Francis Rowe 13 Mar '16

13 Mar '16

Dear flashrom community, Attached is my patch adding a whitelist to flashrom, for these laptops: * ThinkPad R400 * ThinkPad T500 Both laptops were added to coreboot recently, so it makes sense for flashrom to have a whitelist. Hope the community finds this useful. Regards, Francis Rowe. PS: This was made on top of stefanct's git repository, pulled from his github profile.

2 3

[PATCH] Fix compilation on SunOS.
by Stefan Tauner 13 Mar '16

13 Mar '16

This came up when I was testing if building on SunOS still works on the buildbot's instance of OmniOS r151014 which is based on illumos. The fix is - to link against libnsl - a small C type fix in ich_descriptor_tool Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- Makefile | 2 +- util/ich_descriptors_tool/ich_descriptors_tool.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/Makefile b/Makefile index 927105d..f94ec7b 100644 --- a/Makefile +++ b/Makefile @@ -926,7 +926,7 @@ endif ifneq ($(NEED_POSIX_SOCKETS), ) ifeq ($(TARGET_OS), SunOS) -LIBS += -lsocket +LIBS += -lsocket -lnsl endif endif diff --git a/util/ich_descriptors_tool/ich_descriptors_tool.c b/util/ich_descriptors_tool/ich_descriptors_tool.c index c3d9ba1..ad3b6f0 100644 --- a/util/ich_descriptors_tool/ich_descriptors_tool.c +++ b/util/ich_descriptors_tool/ich_descriptors_tool.c @@ -170,7 +170,7 @@ int main(int argc, char *argv[]) usage(argv, "Seeking to the end of the file failed"); #ifdef HAVE_MMAP - buf = mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); + buf = (uint32_t *)mmap(NULL, len, PROT_READ, MAP_PRIVATE, fd, 0); if (buf == (void *) -1) #endif { -- Kind regards, Stefan Tauner

1 0

[PATCH] Rewrite and fix corner case in sb600spi
by Carl-Daniel Hailfinger 12 Mar '16

12 Mar '16

Specifying spispeed=reserved as programmer parameter resulted in selecting the default SPI speed instead of aborting. Rewrite the logic to be more readable. Note: I prefer ! instead of == 0, but Stefan Tauner prefers == 0. A matter of taste. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-sb600_spi_speedselection_cleanup/sb600spi.c =================================================================== --- flashrom-sb600_spi_speedselection_cleanup/sb600spi.c (Revision 1948) +++ flashrom-sb600_spi_speedselection_cleanup/sb600spi.c (Arbeitskopie) @@ -387,24 +387,22 @@ static int handle_speed(struct pci_dev *dev) { uint32_t tmp; - int8_t spispeed_idx = 3; /* Default to 16.5 MHz */ + uint8_t spispeed_idx = 3; /* Default to 16.5 MHz */ char *spispeed = extract_programmer_param("spispeed"); if (spispeed != NULL) { - if (strcasecmp(spispeed, "reserved") != 0) { - int i; - for (i = 0; i < ARRAY_SIZE(spispeeds); i++) { - if (strcasecmp(spispeeds[i].name, spispeed) == 0) { - spispeed_idx = i; - break; - } + int i; + for (i = 0; i < ARRAY_SIZE(spispeeds); i++) { + if (strcasecmp(spispeeds[i].name, spispeed) == 0) { + spispeed_idx = i; + break; } - /* Only Yangtze supports the second half of indices; no 66 MHz before SB8xx. */ - if ((amd_gen < CHIPSET_YANGTZE && spispeed_idx > 3) || - (amd_gen < CHIPSET_SB89XX && spispeed_idx == 0)) - spispeed_idx = -1; } - if (spispeed_idx < 0) { + /* "reserved" is not a valid speed. + * Only Yangtze supports the second half of indices; no 66 MHz before SB8xx. */ + if ((strcasecmp(spispeed, "reserved") == 0) || + (amd_gen < CHIPSET_YANGTZE && spispeed_idx > 3) || + (amd_gen < CHIPSET_SB89XX && spispeed_idx == 0)) { msg_perr("Error: Invalid spispeed value: '%s'.\n", spispeed); free(spispeed); return 1;

2 4

[commit] r1949 - trunk
by repository service 12 Mar '16

12 Mar '16

Author: hailfinger Date: Sat Mar 12 20:49:14 2016 New Revision: 1949 URL: http://flashrom.org/trac/flashrom/changeset/1949 Log: Specifying spispeed=reserved as programmer parameter resulted in selecting the default SPI speed instead of aborting. Rewrite the logic to be more readable. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/sb600spi.c Modified: trunk/sb600spi.c ============================================================================== --- trunk/sb600spi.c Sun Mar 6 23:32:16 2016 (r1948) +++ trunk/sb600spi.c Sat Mar 12 20:49:14 2016 (r1949) @@ -387,24 +387,25 @@ static int handle_speed(struct pci_dev *dev) { uint32_t tmp; - int8_t spispeed_idx = 3; /* Default to 16.5 MHz */ + uint8_t spispeed_idx = 3; /* Default to 16.5 MHz */ char *spispeed = extract_programmer_param("spispeed"); if (spispeed != NULL) { - if (strcasecmp(spispeed, "reserved") != 0) { - int i; - for (i = 0; i < ARRAY_SIZE(spispeeds); i++) { - if (strcasecmp(spispeeds[i].name, spispeed) == 0) { - spispeed_idx = i; - break; - } + unsigned int i; + for (i = 0; i < ARRAY_SIZE(spispeeds); i++) { + if (strcasecmp(spispeeds[i].name, spispeed) == 0) { + spispeed_idx = i; + break; } - /* Only Yangtze supports the second half of indices; no 66 MHz before SB8xx. */ - if ((amd_gen < CHIPSET_YANGTZE && spispeed_idx > 3) || - (amd_gen < CHIPSET_SB89XX && spispeed_idx == 0)) - spispeed_idx = -1; } - if (spispeed_idx < 0) { + /* "reserved" is not a valid speed. + * Error out on speeds not present in the spispeeds array. + * Only Yangtze supports the second half of indices. + * No 66 MHz before SB8xx. */ + if ((strcasecmp(spispeed, "reserved") == 0) || + (i == ARRAY_SIZE(spispeeds)) || + (amd_gen < CHIPSET_YANGTZE && spispeed_idx > 3) || + (amd_gen < CHIPSET_SB89XX && spispeed_idx == 0)) { msg_perr("Error: Invalid spispeed value: '%s'.\n", spispeed); free(spispeed); return 1;

1 0

EN25Q128 (Thomson TG582n router) flash problem?
by Adrian Graham 12 Mar '16

12 Mar '16

Hi, I'm trying to re-flash this 16mb chip with the original contents I dumped before attempting to flash a new bootloader for OpenWRT installation, all the flashing of various CFE bootloaders was successful and the last erase I did was also successful. However this happens when I try to re-flash: pi@raspberrypi ~ $ flashrom -p linux_spi:dev=/dev/spidev0.0 -c"EN25Q128" -w EN25Q128_flash.bin --verbose flashrom v0.9.8-r1888 on Linux 4.1.18-v7+ (armv7l) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.1, GCC 4.9.2, little endian Command line (6 args): flashrom -p linux_spi:dev=/dev/spidev0.0 -cEN25Q128 -w EN25Q128_flash.bin --verbose Calibrating delay loop... OS timer resolution is 3 usecs, 297M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1011 us, 10000 myus = 10067 us, 12 myus = 13 us, OK. Initializing linux_spi programmer Using device /dev/spidev0.0 The following protocols are supported: SPI. Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3018 Found Eon flash chip "EN25Q128" (16384 kB, SPI) on linux_spi. Chip status register is 0x00. This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash chip. Please include the flashrom log file for all operations you tested (see the man page for details), and mention which mainboard or programmer you tested in the subject line. Thanks for your help! Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x000fff:W, 0x001000-0x001fff:W, 0x002000-0x002fff:S, 0x003000-0x003fff:W, 0x004000-0x004fff:W, 0x005000-0x005fff:W, 0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S, 0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:W, . . . {Snip} . . . 0xff3000-0xff3fff:S, 0xff4000-0xff4fff:S, 0xff5000-0xff5fff:S, 0xff6000-0xff6fff:S, 0xff7000-0xff7fff:S, 0xff8000-0xff8fff:S, 0xff9000-0xff9fff:S, 0xffa000-0xffafff:S, 0xffb000-0xffbfff:S, 0xffc000-0xffcfff:S, 0xffd000-0xffdfff:S, 0xffe000-0xffefff:S, 0xfff000-0xffffff:S Erase/write done. Verifying flash... FAILED at 0x0019f8d1! Expected=0x92, Found=0x85, failed byte count from 0x00000000-0x00ffffff: 0x898 Your flash chip is in an unknown state. Please report this on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org, thanks! pi@raspberrypi ~ $ This is version 0.9.8 if you guys are still out there. Thanks! -- Adrian/Witchy Binary Dinosaurs creator/curator Www.binarydinosaurs.co.uk - the UK's biggest private home computer collection?

2 9

Re: [flashrom] Supermicro X9SRH-7F/7TF
by Stefan Tauner 12 Mar '16

12 Mar '16

On Fri, 11 Mar 2016 08:25:16 -0800 Eric Donaldson <eric(a)zadarastorage.com> wrote: > Sorry about that, thought I had included the command I was running. I was > just running the probe on it to figure out if I was going to be able to > read and write to flash, then it said to run it verbosely and submit it. > `flashrom -p internal:pci=01:00.0` I think you are confusing the internal programmer with nicintel_spi (etc). The internal programmer is actually used to access the flash chip of the mainboard containing the firmware of the board and possibly its on-board peripherals. Thus it *might* contain the PXE firmware as well but there is no easy way to prepare images for that. However, from what you wrote so far I think you want to use nicintel_spi and friends to access the boot flash of dedicated NICs. For them the pci parameter makes way more sense as well :) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] Supermicro X9SRH-7F/7TF
by Stefan Tauner 11 Mar '16

11 Mar '16

On Thu, 10 Mar 2016 10:53:29 -0800 Eric Donaldson <eric(a)zadarastorage.com> wrote: > Was poking around at messing with the NIC ROMs, recieved the recommendation > to send an email with the verbose output. > Thanks for the log. However, I am not entirely sure why it was recommended to you to send it in without further explanation. Did you try to write to the flash? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Supermicro X9SRH-7F/7TF
by Eric Donaldson 10 Mar '16

10 Mar '16

Was poking around at messing with the NIC ROMs, recieved the recommendation to send an email with the verbose output. *Eric Donaldson* *DevOps Engineer**Zadara Storage* eric(a)zadarastorage.com Skype: eric_zadara Twitter: @ZadaraStorage Website <http://www.zadarastorage.com/> | Blog <http://www.zadarastorage.com/blog/> | LinkedIn <http://www.linkedin.com/company/zadara-storage/> | Facebook <http://www.facebook.com/ZadaraStorage.VPSA> | Twitter <http://twitter.com/zadaraStorage> | YouTube <http://www.youtube.com/playlist?list=PLZHbMSlUCWob2xFDopFs10UiEwEF8CHg_>

1 0

Re: [flashrom] problems with flashrom
by ryzomone＠gmail.com 09 Mar '16

09 Mar '16

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom