- flashrom - mail.coreboot.org

Re: [flashrom] problems with flashrom
by ryzomone＠gmail.com 09 Mar '16

09 Mar '16

2 1

Re: [flashrom] [PATCH] Add support for GNU Hurd.
by François Revol 09 Mar '16

09 Mar '16

On 06/03/2016 04:57, Stefan Tauner wrote: > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > --- > hwaccess.c | 8 +++++++- > os.h | 3 +++ > 2 files changed, 10 insertions(+), 1 deletion(-) > Damn, I really need to finish Haiku support before someone sends a patch for Minix :D François.

1 0

hi need help EFI unlock
by edival lopes 08 Mar '16

08 Mar '16

hi there. my mac is locked i need help to unlock the efi password what i meed to do. and what i use for it? thanks Sent from my iPhone

1 0

[PATCH] Add support for SST39LF010, SST39LF020 and SST39LF040
by Hatim Kanchwala 07 Mar '16

07 Mar '16

Hello, I am learning about parallel flash chips. My approach is to go through datasheets of chips supported by flashrom and then add support for other member chips of the family. AFAIK, following three chips differ from VF variants only in voltage range. I was able to find very little about parallel flash on the internet, so I will continue with this approach (what do you guys think? :P). If you have any resources or any particular parallel chip family in mind, please let me know (via mail or IRC ;)). Thanks! :) Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> --- flashchips.c | 81 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 6 ++--- 2 files changed, 84 insertions(+), 3 deletions(-) diff --git a/flashchips.c b/flashchips.c index 0fc1b7a..b8fff3c 100644 --- a/flashchips.c +++ b/flashchips.c @@ -12862,26 +12862,107 @@ const struct flashchip flashchips[] = { { { .eraseblocks = { {256 * 1024, 1} }, .block_erase = erase_chip_block_jedec, } }, .write = write_jedec, .read = read_memmapped, .voltage = {3000, 3600}, }, { .vendor = "SST", + .name = "SST39LF010", + .bustype = BUS_PARALLEL, + .manufacture_id = SST_ID, + .model_id = SST_SST39VF010, + .total_size = 128, + .page_size = 4096, + .feature_bits = FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = 1, /* 150 ns */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 32} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {128 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + .voltage = {3000, 3600}, + }, + + { + .vendor = "SST", + .name = "SST39LF020", + .bustype = BUS_PARALLEL, + .manufacture_id = SST_ID, + .model_id = SST_SST39VF020, + .total_size = 256, + .page_size = 4096, + .feature_bits = FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = 1, /* 150 ns */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + .voltage = {3000, 3600}, + }, + + { + .vendor = "SST", + .name = "SST39LF040", + .bustype = BUS_PARALLEL, + .manufacture_id = SST_ID, + .model_id = SST_SST39VF040, + .total_size = 512, + .page_size = 4096, + .feature_bits = FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = 1, /* 150 ns */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + .voltage = {3000, 3600}, + }, + + { + .vendor = "SST", .name = "SST39SF512", .bustype = BUS_PARALLEL, .manufacture_id = SST_ID, .model_id = SST_SST39SF512, .total_size = 64, .page_size = 4096, .feature_bits = FEATURE_EITHER_RESET, .tested = TEST_OK_PREW, .probe = probe_jedec, .probe_timing = 1, /* 150 ns */ .block_erasers = { { diff --git a/flashchips.h b/flashchips.h index 9ffb30f..3d61ad1 100644 --- a/flashchips.h +++ b/flashchips.h @@ -709,29 +709,29 @@ #define SST_SST29EE010 0x07 #define SST_SST29LE010 0x08 /* Same as SST29VE010 */ #define SST_SST29EE020A 0x10 /* Same as SST29EE020 */ #define SST_SST29LE020 0x12 /* Same as SST29VE020 */ #define SST_SST29SF020 0x24 #define SST_SST29VF020 0x25 #define SST_SST29SF040 0x13 #define SST_SST29VF040 0x14 #define SST_SST39SF512 0xB4 #define SST_SST39SF010 0xB5 #define SST_SST39SF020 0xB6 /* Same as 39SF020A */ #define SST_SST39SF040 0xB7 #define SST_SST39VF512 0xD4 -#define SST_SST39VF010 0xD5 -#define SST_SST39VF020 0xD6 /* Same as 39LF020 */ -#define SST_SST39VF040 0xD7 /* Same as 39LF040 */ +#define SST_SST39VF010 0xD5 /* Same as SST39LF010 */ +#define SST_SST39VF020 0xD6 /* Same as SST39LF020 */ +#define SST_SST39VF040 0xD7 /* Same as SST39LF040 */ #define SST_SST39VF080 0xD8 /* Same as 39LF080/39VF080/39VF088 */ #define SST_SST45VF512 0x41 /* REMS, read opcode 0xFF */ #define SST_SST45LF010 0x42 /* REMS, read opcode 0xFF, 'funny' other opcodes */ #define SST_SST45VF010 0x45 /* REMS, read opcode 0xFF */ #define SST_SST45VF020 0x43 /* REMS, read opcode 0xFF */ #define SST_SST49LF040B 0x50 #define SST_SST49LF040 0x51 #define SST_SST49LF020 0x61 #define SST_SST49LF020A 0x52 #define SST_SST49LF030A 0x1C #define SST_SST49LF080A 0x5B #define SST_SST49LF002A 0x57 #define SST_SST49LF003A 0x1B -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

1 0

Re: [flashrom] [PATCH] Add support for GNU Hurd.
by Carl-Daniel Hailfinger 06 Mar '16

06 Mar '16

On 06.03.2016 16:32, Stefan Tauner wrote: > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > --- > > New version avoiding breaking any other platform by guarding the inclusion > of sys/io.h as it should have been in the first place. > I have actually tested this with the internal programmer within a VirtualBox > VM and it worked as expected (i.e. not really but it did not explode either). So forced read did turn up the vbox BIOS? If yes, this is Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel

2 1

[commit] r1948 - trunk
by repository service 06 Mar '16

06 Mar '16

Author: stefanct Date: Sun Mar 6 23:32:16 2016 New Revision: 1948 URL: http://flashrom.org/trac/flashrom/changeset/1948 Log: Add support for GNU Hurd. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/hwaccess.c trunk/os.h Modified: trunk/hwaccess.c ============================================================================== --- trunk/hwaccess.c Sun Mar 6 15:33:49 2016 (r1947) +++ trunk/hwaccess.c Sun Mar 6 23:32:16 2016 (r1948) @@ -33,12 +33,17 @@ #include "flash.h" #include "hwaccess.h" -#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun)) +#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun) || defined(__gnu_hurd__)) #error "Unknown operating system" #endif #define USE_IOPL (IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__)) #define USE_DEV_IO (defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__)) +#define USE_IOPERM (defined(__gnu_hurd__)) + +#if USE_IOPERM +#include <sys/io.h> +#endif #if IS_X86 && USE_DEV_IO int io_fd; @@ -82,6 +87,8 @@ sysi86(SI86V86, V86SC_IOPL, 0); #elif USE_DEV_IO close(io_fd); +#elif USE_IOPERM + ioperm(0, 65536, 0); #elif USE_IOPL iopl(0); #endif @@ -97,6 +104,8 @@ if (sysi86(SI86V86, V86SC_IOPL, PS_IOPL) != 0) { #elif USE_DEV_IO if ((io_fd = open("/dev/io", O_RDWR)) < 0) { +#elif USE_IOPERM + if (ioperm(0, 65536, 1) != 0) { #elif USE_IOPL if (iopl(3) != 0) { #endif Modified: trunk/os.h ============================================================================== --- trunk/os.h Sun Mar 6 15:33:49 2016 (r1947) +++ trunk/os.h Sun Mar 6 23:32:16 2016 (r1948) @@ -56,6 +56,9 @@ // libpayload #elif defined(__LIBPAYLOAD__) #define __FLASHROM_OS__ "libpayload" +// GNU Hurd +#elif defined(__gnu_hurd__) +#define __FLASHROM_OS__ "Hurd" // Linux #elif defined(__linux__) // There are various flags in use on Android apparently. __ANDROID__ seems to be the most trustworthy.

1 0

[PATCH] Add support for GNU Hurd.
by Stefan Tauner 06 Mar '16

06 Mar '16

Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- New version avoiding breaking any other platform by guarding the inclusion of sys/io.h as it should have been in the first place. I have actually tested this with the internal programmer within a VirtualBox VM and it worked as expected (i.e. not really but it did not explode either). hwaccess.c | 11 ++++++++++- os.h | 3 +++ 2 files changed, 13 insertions(+), 1 deletion(-) diff --git a/hwaccess.c b/hwaccess.c index 528550d..1901ee6 100644 --- a/hwaccess.c +++ b/hwaccess.c @@ -33,12 +33,17 @@ #include "flash.h" #include "hwaccess.h" -#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun)) +#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun) || defined(__gnu_hurd__)) #error "Unknown operating system" #endif #define USE_IOPL (IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__)) #define USE_DEV_IO (defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__)) +#define USE_IOPERM (defined(__gnu_hurd__)) + +#if USE_IOPERM +#include <sys/io.h> +#endif #if IS_X86 && USE_DEV_IO int io_fd; @@ -82,6 +87,8 @@ static int release_io_perms(void *p) sysi86(SI86V86, V86SC_IOPL, 0); #elif USE_DEV_IO close(io_fd); +#elif USE_IOPERM + ioperm(0, 65536, 0); #elif USE_IOPL iopl(0); #endif @@ -97,6 +104,8 @@ int rget_io_perms(void) if (sysi86(SI86V86, V86SC_IOPL, PS_IOPL) != 0) { #elif USE_DEV_IO if ((io_fd = open("/dev/io", O_RDWR)) < 0) { +#elif USE_IOPERM + if (ioperm(0, 65536, 1) != 0) { #elif USE_IOPL if (iopl(3) != 0) { #endif diff --git a/os.h b/os.h index e5f72e4..b59e087 100644 --- a/os.h +++ b/os.h @@ -56,6 +56,9 @@ // libpayload #elif defined(__LIBPAYLOAD__) #define __FLASHROM_OS__ "libpayload" +// GNU Hurd +#elif defined(__gnu_hurd__) +#define __FLASHROM_OS__ "Hurd" // Linux #elif defined(__linux__) // There are various flags in use on Android apparently. __ANDROID__ seems to be the most trustworthy. -- Kind regards, Stefan Tauner

1 0

[PATCH] Add support for GD25VQ21B, GD25VQ40C, GD25VQ80C and GD25VQ16C
by Hatim Kanchwala 06 Mar '16

06 Mar '16

Hello, Whitespace and other issues have been fixed. Sadly, test status still remains untested due to delay in shipment of some components :( Shipment delivey has become unreliable so I will not be giving an estimate for that, but once it arrives, I will test and send patches the same day. Stefan, this patch does not include some other changes you had introduced because I thought those changes were not related to the above commit message ;) Thanks :) Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> --- flashchips.c | 159 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 5 +- 2 files changed, 163 insertions(+), 1 deletion(-) diff --git a/flashchips.c b/flashchips.c index 238389b..33df2a4 100644 --- a/flashchips.c +++ b/flashchips.c @@ -6285,26 +6285,65 @@ const struct flashchip flashchips[] = { .eraseblocks = { {1024 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", + .name = "GD25VQ21B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ21B, + .total_size = 256, + .page_size = 256, + /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 8} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", .name = "GD25VQ41B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25VQ41B, .total_size = 512, .page_size = 256, /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { @@ -6324,26 +6363,146 @@ const struct flashchip flashchips[] = { .eraseblocks = { {512 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, /* TODO: 2nd Status Register; read 0x35 */ .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2300, 3600}, }, { + .vendor = "GigaDevice", + .name = "GD25VQ40C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ41B, + .total_size = 512, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ80C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ80C, + .total_size = 1024, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 256} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 32} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ16C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ16C, + .total_size = 2 * 1024, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 512} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 64} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 32} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { .vendor = "Hyundai", .name = "HY29F002T", .bustype = BUS_PARALLEL, .manufacture_id = HYUNDAI_ID, .model_id = HYUNDAI_HY29F002T, .total_size = 256, .page_size = 256 * 1024, .feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */ .tested = TEST_OK_PRE, .probe = probe_jedec, .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ .block_erasers = { diff --git a/flashchips.h b/flashchips.h index a109e94..ac1901f 100644 --- a/flashchips.h +++ b/flashchips.h @@ -368,27 +368,30 @@ #define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25QB */ #define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25QB */ #define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */ #define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */ #define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ #define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ #define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B and GD25Q128C only, can be distinguished by SFDP */ #define GIGADEVICE_GD25LQ40 0x6013 #define GIGADEVICE_GD25LQ80 0x6014 #define GIGADEVICE_GD25LQ16 0x6015 #define GIGADEVICE_GD25LQ32 0x6016 #define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */ #define GIGADEVICE_GD25LQ128 0x6018 -#define GIGADEVICE_GD25VQ41B 0x4213 +#define GIGADEVICE_GD25VQ21B 0x4212 +#define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ +#define GIGADEVICE_GD25VQ80C 0x4214 +#define GIGADEVICE_GD25VQ16C 0x4215 #define GIGADEVICE_GD29GL064CAB 0x7E0601 #define HYUNDAI_ID 0xAD /* Hyundai */ #define HYUNDAI_HY29F400T 0x23 /* Same as HY29F400AT */ #define HYUNDAI_HY29F800B 0x58 /* Same as HY29F800AB */ #define HYUNDAI_HY29LV800B 0x5B #define HYUNDAI_HY29F040A 0xA4 #define HYUNDAI_HY29F400B 0xAB /* Same as HY29F400AB */ #define HYUNDAI_HY29F002B 0x34 #define HYUNDAI_HY29F002T 0xB0 #define HYUNDAI_HY29LV400T 0xB9 #define HYUNDAI_HY29LV400B 0xBA #define HYUNDAI_HY29F080 0xD5 -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

2 2

[commit] r1947 - trunk
by repository service 06 Mar '16

06 Mar '16

Author: stefanct Date: Sun Mar 6 15:33:49 2016 New Revision: 1947 URL: http://flashrom.org/trac/flashrom/changeset/1947 Log: Add support for GD25VQ21B, GD25VQ40C, GD25VQ80C and GD25VQ16C. Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/flashchips.c trunk/flashchips.h Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Sun Feb 28 23:04:51 2016 (r1946) +++ trunk/flashchips.c Sun Mar 6 15:33:49 2016 (r1947) @@ -6295,6 +6295,85 @@ { .vendor = "GigaDevice", + .name = "GD25VQ21B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ21B, + .total_size = 256, + .page_size = 256, + /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 8} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ40C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ41B, + .total_size = 512, + .page_size = 256, + /* Supports SFDP */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", .name = "GD25VQ41B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, @@ -6325,9 +6404,88 @@ .block_erase = spi_block_erase_c7, } }, - /* TODO: 2nd Status Register; read 0x35 */ .printlock = spi_prettyprint_status_register_bp4_srwd, - .unlock = spi_disable_blockprotect_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ80C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ80C, + .total_size = 1024, + .page_size = 256, + /* Supports SFDP */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 256} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 32} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ16C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ16C, + .total_size = 2 * 1024, + .page_size = 256, + /* Supports SFDP */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 512} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 64} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 32} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, /* TODO: 2nd status reg (read with 0x35) */ .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2300, 3600}, Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Sun Feb 28 23:04:51 2016 (r1946) +++ trunk/flashchips.h Sun Mar 6 15:33:49 2016 (r1947) @@ -372,13 +372,16 @@ #define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ #define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ #define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B and GD25Q128C only, can be distinguished by SFDP */ +#define GIGADEVICE_GD25VQ21B 0x4212 +#define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ +#define GIGADEVICE_GD25VQ80C 0x4214 +#define GIGADEVICE_GD25VQ16C 0x4215 #define GIGADEVICE_GD25LQ40 0x6013 #define GIGADEVICE_GD25LQ80 0x6014 #define GIGADEVICE_GD25LQ16 0x6015 #define GIGADEVICE_GD25LQ32 0x6016 #define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */ #define GIGADEVICE_GD25LQ128 0x6018 -#define GIGADEVICE_GD25VQ41B 0x4213 #define GIGADEVICE_GD29GL064CAB 0x7E0601 #define HYUNDAI_ID 0xAD /* Hyundai */

1 0

the size doesn't coincide
by Юра Клепиков 06 Mar '16

06 Mar '16

whether at me the router with the help the test of a clip on poderzhvayemy mother has died I want to restore it unfortunately an insertion of less flash and on it perhaps fill in it I can turn off check of the size ? without a conclusion error: Image size (262144 B) doesn't match the flash chip's size (524288 B)

2 1

problems with flashrom
by ryzomone＠gmail.com 06 Mar '16

06 Mar '16

Hey there, i have a problem I have read out my 25Q064A (N25Q064...3E) successful with flashrom and it seams to erasing successful too but after writing it said verifying failed at all time. Thhe backup dumb too. Is there a solving for my Problem . Flashrom sais some times the chip is in an unknown state. Did i brick my EFI chip ?? Thanks for your answers

2 1

test
by Carl-Daniel Hailfinger 06 Mar '16

06 Mar '16

Testing if the transition to https everywhere causes any problems with mailman...

1 1

[PATCH] Add support for GNU Hurd.
by Stefan Tauner 06 Mar '16

06 Mar '16

Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- hwaccess.c | 8 +++++++- os.h | 3 +++ 2 files changed, 10 insertions(+), 1 deletion(-) diff --git a/hwaccess.c b/hwaccess.c index 528550d..cfb6291 100644 --- a/hwaccess.c +++ b/hwaccess.c @@ -25,6 +25,7 @@ #include <stdlib.h> #include <errno.h> #include <sys/types.h> +#include <sys/io.h> #if !defined (__DJGPP__) && !defined(__LIBPAYLOAD__) /* No file access needed/possible to get hardware access permissions. */ #include <unistd.h> @@ -33,12 +34,13 @@ #include "flash.h" #include "hwaccess.h" -#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun)) +#if !(IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__) || defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__) || defined(__DJGPP__) || defined(__LIBPAYLOAD__) || defined(__sun) || defined(__gnu_hurd__)) #error "Unknown operating system" #endif #define USE_IOPL (IS_LINUX || IS_MACOSX || defined(__NetBSD__) || defined(__OpenBSD__)) #define USE_DEV_IO (defined(__FreeBSD__) || defined(__FreeBSD_kernel__) || defined(__DragonFly__)) +#define USE_IOPERM (defined(__gnu_hurd__)) #if IS_X86 && USE_DEV_IO int io_fd; @@ -82,6 +84,8 @@ static int release_io_perms(void *p) sysi86(SI86V86, V86SC_IOPL, 0); #elif USE_DEV_IO close(io_fd); +#elif USE_IOPERM + ioperm(0, 65536, 0); #elif USE_IOPL iopl(0); #endif @@ -97,6 +101,8 @@ int rget_io_perms(void) if (sysi86(SI86V86, V86SC_IOPL, PS_IOPL) != 0) { #elif USE_DEV_IO if ((io_fd = open("/dev/io", O_RDWR)) < 0) { +#elif USE_IOPERM + if (ioperm(0, 65536, 1) != 0) { #elif USE_IOPL if (iopl(3) != 0) { #endif diff --git a/os.h b/os.h index e5f72e4..b59e087 100644 --- a/os.h +++ b/os.h @@ -56,6 +56,9 @@ // libpayload #elif defined(__LIBPAYLOAD__) #define __FLASHROM_OS__ "libpayload" +// GNU Hurd +#elif defined(__gnu_hurd__) +#define __FLASHROM_OS__ "Hurd" // Linux #elif defined(__linux__) // There are various flags in use on Android apparently. __ANDROID__ seems to be the most trustworthy. -- Kind regards, Stefan Tauner

1 0

[PATCH] Add a bunch of new/tested stuff and various small changes 25.
by Stefan Tauner 05 Mar '16

05 Mar '16

Tested mainboards: OK: - ASRock Fatal1ty 970 Performance and P4i65G Reported by anonymous email message ID: 932677687262b1300eaf14260999d9262c31(a)guerrillamail.com The latter actually had a tested board enable already. Flash chips: - GigaDevice GD25VQ41B to PREW (+PREW) Reported by David Hendricks - Winbond W39V040FB to PREW (+EW) Reported by fjed on IRC Miscellaneous: - Change PCI IDs of "MS-6577 (Xenon)" board enable. The previous IDs contained the on-board display adapter which is disabled when a dedicated graphics card is installed. - Add a note to the README how to overcome the clang warning if only a single programmer is enabled. - Fix some typo and manpage problems found by lintian - r1920 introduced some explicit calls to pkg-config instead of $(PKG_CONFIG). This patch corrects that. - Add some overrides to the Makefile in case someone/something sets variables like CPPFLAGS or LDFLAGS as command line parameters Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- Makefile | 34 ++++++++++++++--------------- README | 6 ++++++ board_enable.c | 2 +- flashchips.c | 66 ++++++++++++++++++++++++++++----------------------------- flashrom.8.tmpl | 38 ++++++++++++++++++--------------- pickit2_spi.c | 2 +- print.c | 4 ++-- sb600spi.c | 2 +- 8 files changed, 82 insertions(+), 72 deletions(-) diff --git a/Makefile b/Makefile index 927105d..d9a70b3 100644 --- a/Makefile +++ b/Makefile @@ -314,7 +314,7 @@ UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes else override CONFIG_PONY_SPI = no endif -# Dediprog, USB-Blaster, PICkit2, CH341A and FT2232 are not supported with libpayload (missing libusb support) +# Dediprog, USB-Blaster, PICkit2, CH341A and FT2232 are not supported with libpayload (missing libusb support). ifeq ($(CONFIG_DEDIPROG), yes) UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes else @@ -661,22 +661,22 @@ override CONFIG_CH341A_SPI = no override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_ENABLE_LIBPCI_PROGRAMMERS), no) -override CONFIG_INTERNAL = no -override CONFIG_NIC3COM = no -override CONFIG_GFXNVIDIA = no -override CONFIG_SATASII = no -override CONFIG_ATAHPT = no -override CONFIG_ATAVIA = no -override CONFIG_ATAPROMISE = no -override CONFIG_IT8212 = no -override CONFIG_DRKAISER = no -override CONFIG_NICREALTEK = no -override CONFIG_NICNATSEMI = no -override CONFIG_NICINTEL = no -override CONFIG_NICINTEL_SPI = no -override CONFIG_NICINTEL_EEPROM = no -override CONFIG_OGP_SPI = no -override CONFIG_SATAMV = no +override CONFIG_INTERNAL = no +override CONFIG_NIC3COM = no +override CONFIG_GFXNVIDIA = no +override CONFIG_SATASII = no +override CONFIG_ATAHPT = no +override CONFIG_ATAVIA = no +override CONFIG_ATAPROMISE = no +override CONFIG_IT8212 = no +override CONFIG_DRKAISER = no +override CONFIG_NICREALTEK = no +override CONFIG_NICNATSEMI = no +override CONFIG_NICINTEL = no +override CONFIG_NICINTEL_SPI = no +override CONFIG_NICINTEL_EEPROM = no +override CONFIG_OGP_SPI = no +override CONFIG_SATAMV = no endif # Bitbanging SPI infrastructure, default off unless needed. diff --git a/README b/README index 604e793..ab761f7 100644 --- a/README +++ b/README @@ -136,6 +136,12 @@ Processor architecture dependent features: use port-based I/O which is not directly available on non-x86. Those programmers will be disabled automatically if you run "make". +Compiler quirks: + +If you are using clang and if you want to enable only one driver, you may hit an +overzealous compiler warning from clang. Compile with "make WARNERROR=no" to +force it to continue and enjoy. + Installation ------------ diff --git a/board_enable.c b/board_enable.c index 7b152d1..2d52fe1 100644 --- a/board_enable.c +++ b/board_enable.c @@ -2440,7 +2440,7 @@ const struct board_match board_matches[] = { {0x8086, 0x7190, 0, 0, 0x8086, 0x7110, 0, 0, "^MS-6163 (i440BX)$", NULL, NULL, P3, "MSI", "MS-6163 (MS-6163 Pro)", 0, OK, intel_piix4_gpo14_raise}, {0x8086, 0x244b, 0x1462, 0x3910, 0x8086, 0x2442, 0x1462, 0x3910, NULL, NULL, NULL, P3, "MSI", "MS-6391 (845 Pro4)", 0, OK, intel_ich_gpio23_raise}, {0x1039, 0x0745, 0, 0, 0x1039, 0x0018, 0, 0, "^MS-6561", NULL, NULL, P3, "MSI", "MS-6561 (745 Ultra)", 0, OK, w836xx_memw_enable_2e}, - {0x8086, 0x2560, 0x1462, 0x5770, 0x8086, 0x2562, 0x1462, 0x5778, NULL, NULL, NULL, P3, "MSI", "MS-6577 (Xenon)", 0, OK, w83627hf_gpio25_raise_2e}, + {0x8086, 0x2560, 0x1462, 0x5770, 0x8086, 0x24C3, 0x1462, 0x5770, NULL, NULL, NULL, P3, "MSI", "MS-6577 (Xenon)", 0, OK, w83627hf_gpio25_raise_2e}, {0x13f6, 0x0111, 0x1462, 0x5900, 0x1106, 0x3177, 0x1106, 0, NULL, NULL, NULL, P3, "MSI", "MS-6590 (KT4 Ultra)", 0, OK, board_msi_kt4v}, {0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, "^MS-7094$", NULL, NULL, P3, "MSI", "MS-7094 (K8T Neo2-F V2.0)", 0, OK, w83627thf_gpio44_raise_2e}, {0x1106, 0x0571, 0x1462, 0x7120, 0x1106, 0x3065, 0x1462, 0x7120, NULL, NULL, NULL, P3, "MSI", "MS-6712 (KT4V)", 0, OK, board_msi_kt4v}, diff --git a/flashchips.c b/flashchips.c index 238389b..f8d3628 100644 --- a/flashchips.c +++ b/flashchips.c @@ -5368,13 +5368,13 @@ const struct flashchip flashchips[] = { .probe_timing = TIMING_ZERO, .block_erasers = { - { - .eraseblocks = { {64 * 1024, 8} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { {64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, .printlock = spi_prettyprint_status_register_bp2_srwd, .unlock = spi_disable_blockprotect_bp2_srwd, @@ -5399,13 +5399,13 @@ const struct flashchip flashchips[] = { .probe_timing = TIMING_ZERO, .block_erasers = { - { - .eraseblocks = { {64 * 1024, 16} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { {64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, .printlock = spi_prettyprint_status_register_bp2_srwd, .unlock = spi_disable_blockprotect_bp2_srwd, @@ -6303,27 +6303,27 @@ const struct flashchip flashchips[] = { .page_size = 256, /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, - .block_erasers = + .block_erasers = { - { - .eraseblocks = { { 4 * 1024, 128} }, - .block_erase = spi_block_erase_20, - }, { - .eraseblocks = { { 32 * 1024, 16} }, - .block_erase = spi_block_erase_52, - }, { - .eraseblocks = { { 64 * 1024, 8} }, - .block_erase = spi_block_erase_d8, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_60, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = spi_block_erase_c7, - } + { + .eraseblocks = { { 4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } }, /* TODO: 2nd Status Register; read 0x35 */ .printlock = spi_prettyprint_status_register_bp4_srwd, @@ -15469,7 +15469,7 @@ const struct flashchip flashchips[] = { .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_jedec, .probe_timing = 10, .block_erasers = diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl index cb77e46..5de735b 100644 --- a/flashrom.8.tmpl +++ b/flashrom.8.tmpl @@ -1,9 +1,11 @@ .\" Load the www device when using groff; provide a fallback for groff's MTO macro that formats email addresses. .ie \n[.g] \ . mso www.tmac -.el \ -. de MTO \\$2 \(la\\$1 \(ra\\$3 +.el \{ +. de MTO + \\$2 \(la\\$1 \(ra\\$3 \ . . +.\} .\" Create wrappers for .MTO and .URL that print only text on systems w/o groff or if not outputting to a HTML .\" device. To that end we need to distinguish HTML output on groff from other configurations first. .nr groffhtml 0 @@ -208,7 +210,7 @@ Please note that MediaWiki output is not compiled in by default. Specify the programmer device. This is mandatory for all operations involving any chip access (probe/read/write/...). Currently supported are: .sp -.BR "* internal" " (default, for in-system flashing in the mainboard)" +.BR "* internal" " (for in-system flashing in the mainboard)" .sp .BR "* dummy" " (virtual programmer for testing flashrom)" .sp @@ -237,16 +239,10 @@ cards)" .sp .BR "* it8212" " (for flash ROMs on ITE IT8212F ATA/RAID controller)" .sp -.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family \ -based USB SPI programmer), including the DLP Design DLP-USB1232H, \ -FTDI FT2232H Mini-Module, FTDI FT4232H Mini-Module, openbiosprog-spi, Amontec \ -JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, \ -Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, TIAO/DIYGADGET USB -Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2. +.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family based USB SPI programmer). .sp .BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog, \ -including Arduino-based devices as well as various programmers by Urja Rannikko, \ -Juhana Helovuo, Stefan Tauner and others)." +including some Arduino-based devices)." .sp .BR "* buspirate_spi" " (for SPI flash ROMs attached to a Bus Pirate)" .sp @@ -684,13 +680,18 @@ size (padding to 32 kB is required). .IP This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their -size nor allow to be identified, the controller relies on correct size values written to predefined addresses -within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed -EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST) -M95128, M95256 and OnSemi (Catalyst) CAT25CS128. +size nor allow themselves to be identified, the controller relies on correct size values written to predefined +addresses within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an +unprogrammed EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: +Atmel AT25128, AT25256, Micron (ST) M95128, M95256 and OnSemi (Catalyst) CAT25CS128. .SS .BR "ft2232_spi " programmer .IP +This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design +DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, +Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB +Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2. +.sp An optional parameter specifies the controller type and channel/interface/port it should support. For that you have to use the .sp @@ -736,6 +737,9 @@ syntax. .SS .BR "serprog " programmer .IP +This module supports all programmers speaking the serprog protocol. This includes some Arduino-based devices +as well as various programmers by Urja Rannikko, Juhana Helovuo, Stefan Tauner, Chi Zhang and many others. +.sp A mandatory parameter specifies either a serial device (and baud rate) or an IP/port combination for communicating with the programmer. The device/baud combination has to start with @@ -981,7 +985,7 @@ Please note that the linux_spi driver only works on Linux. .BR "mstarddc_spi " programmer .IP The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging -informations between a computer and attached displays. Its most common uses are getting display capabilities +information between a computer and attached displays. Its most common uses are getting display capabilities through EDID (at I2C address 0x50) and sending commands to the display using the DDC/CI protocol (at address 0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC firmware flash (connected to the Soc through another SPI bus) using an In-System Programming (ISP) port, usually at address 0x49. @@ -1016,7 +1020,7 @@ Example that does not reset the display at the end of the operation: .sp .B " flashrom \-p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1 .sp -Please note that sending the reset command is also inhibited in the event an error occured during the operation. +Please note that sending the reset command is also inhibited in the event an error occurred during the operation. To send the reset command afterwards, you can simply run flashrom once more, in chip probe mode (not specifying an operation), without the .B noreset diff --git a/pickit2_spi.c b/pickit2_spi.c index f1f60a2..f6aa676 100644 --- a/pickit2_spi.c +++ b/pickit2_spi.c @@ -400,7 +400,7 @@ static int pickit2_shutdown(void *data) int pickit2_spi_init(void) { - unsigned int usedevice = 0; // FIXME: allow to select one of multiple devices + unsigned int usedevice = 0; // FIXME: allows one to select one of multiple devices uint8_t buf[CMD_LENGTH] = { CMD_EXEC_SCRIPT, diff --git a/print.c b/print.c index 7b0e8e9..08bad02 100644 --- a/print.c +++ b/print.c @@ -490,11 +490,9 @@ int print_supported(void) case USB: print_supported_devs(prog, "USB"); break; -#if NEED_PCI == 1 case PCI: print_supported_devs(prog, "PCI"); break; -#endif case OTHER: if (prog.devs.note != NULL) { msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); @@ -571,6 +569,7 @@ const struct board_info boards_known[] = { B("ASRock", "AMCP7AION-HT", OK, "http://www.asrock.com/nettop/NVIDIA/ION%20330HT/", "Used in ION 330HT(-BD) barebones."), B("ASRock", "ConRoeXFire-eSATA2", OK, "http://www.asrock.com/mb/overview.asp?model=conroexfire-esata2", NULL), B("ASRock", "E350M1/USB3", OK, "http://www.asrock.com/mb/overview.asp?model=e350m1/usb3", "Vendor firmware writes to flash at shutdown. This probably corrupts the flash in case you write coreboot while running the vendor firmware. Simply updating the vendor firmware should be fine."), + B("ASRock", "Fatal1ty 970 Performance", OK, "http://www.asrock.com/mb/overview.asp?Model=Fatal1ty%20970%20Performance", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "Fatal1ty Z77 Performance", BAD, "http://www.asrock.com/mb/overview.asp?Model=Fatal1ty%20Z77%20Performance", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "G31M-GS", OK, "http://www.asrock.com/mb/overview.asp?Model=G31M-GS", NULL), B("ASRock", "G31M-S rev 2.0", OK, "http://www.asrock.com/mb/overview.asp?model=G31M-S", NULL), @@ -585,6 +584,7 @@ const struct board_info boards_known[] = { B("ASRock", "M3A790GXH/128M", OK, "http://www.asrock.com/mb/overview.asp?Model=M3A790GXH/128M", NULL), B("ASRock", "N61P-S", OK, "http://www.asrock.com/mb/overview.asp?Model=N61P-S", NULL), B("ASRock", "N68C-S UCC", OK, "http://www.asrock.com/mb/overview.asp?Model=N68C-S%20UCC", NULL), + B("ASRock", "P4i65G", OK, "http://www.asrock.com/mb/overview.asp?Model=P4i65G", NULL), B("ASRock", "P4i65GV", OK, "http://www.asrock.com/mb/overview.asp?Model=P4i65GV", NULL), B("ASRock", "Z68 Extreme4", BAD, "http://www.asrock.com/mb/overview.asp?Model=Z68%20Extreme4", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "A7N8X Deluxe", OK, "http://www.asus.com/Motherboards/AMD_Socket_A/A7N8X_Deluxe/", NULL), diff --git a/sb600spi.c b/sb600spi.c index 37ecfd9..9cedbff 100644 --- a/sb600spi.c +++ b/sb600spi.c @@ -511,7 +511,7 @@ static int handle_imc(struct pci_dev *dev) msg_pinfo("Writes have been disabled for safety reasons because the presence of the IMC\n" "was detected and it could interfere with accessing flash memory. Flashrom will\n" "try to disable it temporarily but even then this might not be safe:\n" - "when it is reenabled and after a reboot it expects to find working code\n" + "when it is re-enabled and after a reboot it expects to find working code\n" "in the flash and it is unpredictable what happens if there is none.\n" "\n" "To be safe make sure that there is a working IMC firmware at the right\n" -- Kind regards, Stefan Tauner

1 0

question about Qnap TS 459 pro II and Dell Laptop Latitude E 64100
by forensic.technologie 02 Mar '16

02 Mar '16

Hi, supports flash rom the nas serie ts 459 pro II Is it correct that your software all chips incusive bios clears. Could you me a guide to create a usb sticks give another question is supported flashrom dell Latitude E6410 notebook. Thank you very much Rene

1 0

[PATCH] Support device lists for programmers without PCI/USB IDs
by Carl-Daniel Hailfinger 29 Feb '16

29 Feb '16

Based on an idea by Kyösti Mälkki. Issues: print_wiki is broken right now. Don't compile it in. The internal programmer is listed twice in -L output. Some programmers have stupid indentation in -L output. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-noid_programmers_support_device_list/ogp_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/ogp_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/ogp_spi.c (Arbeitskopie) @@ -47,7 +47,7 @@ static uint32_t ogp_reg__ce; static uint32_t ogp_reg_sck; -const struct dev_entry ogp_spi[] = { +const struct id_dev_entry ogp_spi[] = { {PCI_VENDOR_ID_OGP, 0x0000, OK, "Open Graphics Project", "Development Board OGD1"}, {0}, Index: flashrom-noid_programmers_support_device_list/drkaiser.c =================================================================== --- flashrom-noid_programmers_support_device_list/drkaiser.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/drkaiser.c (Arbeitskopie) @@ -33,7 +33,7 @@ /* Mask to restrict flash accesses to the 128kB memory window. */ #define DRKAISER_MEMMAP_MASK ((1 << 17) - 1) -const struct dev_entry drkaiser_pcidev[] = { +const struct id_dev_entry drkaiser_pcidev[] = { {0x1803, 0x5057, OK, "Dr. Kaiser", "PC-Waechter (Actel FPGA)"}, {0}, Index: flashrom-noid_programmers_support_device_list/pcidev.c =================================================================== --- flashrom-noid_programmers_support_device_list/pcidev.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/pcidev.c (Arbeitskopie) @@ -184,7 +184,7 @@ * also matches the specified bus:device.function. * For convenience, this function also registers its own undo handlers. */ -struct pci_dev *pcidev_init(const struct dev_entry *devs, int bar) +struct pci_dev *pcidev_init(const struct id_dev_entry *devs, int bar) { struct pci_dev *dev; struct pci_dev *found_dev = NULL; Index: flashrom-noid_programmers_support_device_list/gfxnvidia.c =================================================================== --- flashrom-noid_programmers_support_device_list/gfxnvidia.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/gfxnvidia.c (Arbeitskopie) @@ -34,7 +34,7 @@ uint8_t *nvidia_bar; -const struct dev_entry gfx_nvidia[] = { +const struct id_dev_entry gfx_nvidia[] = { {0x10de, 0x0010, NT, "NVIDIA", "Mutara V08 [NV2]" }, {0x10de, 0x0018, NT, "NVIDIA", "RIVA 128" }, {0x10de, 0x0020, NT, "NVIDIA", "RIVA TNT" }, Index: flashrom-noid_programmers_support_device_list/serprog.c =================================================================== --- flashrom-noid_programmers_support_device_list/serprog.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/serprog.c (Arbeitskopie) @@ -44,6 +44,11 @@ #define MSGHEADER "serprog: " +const struct noid_dev_entry serprog_devs[] = { + {"", OK, "All programmer devices speaking the serprog protocol"}, + {0}, +}; + /* * FIXME: This prototype was added to help reduce diffs for the shutdown * registration patch, which shifted many lines of code to place Index: flashrom-noid_programmers_support_device_list/nicrealtek.c =================================================================== --- flashrom-noid_programmers_support_device_list/nicrealtek.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/nicrealtek.c (Arbeitskopie) @@ -30,7 +30,7 @@ static int bios_rom_addr, bios_rom_data; -const struct dev_entry nics_realtek[] = { +const struct id_dev_entry nics_realtek[] = { {0x10ec, 0x8139, OK, "Realtek", "RTL8139/8139C/8139C+"}, {0x10ec, 0x8169, NT, "Realtek", "RTL8169"}, {0x1113, 0x1211, OK, "SMC", "1211TX"}, /* RTL8139 clone */ Index: flashrom-noid_programmers_support_device_list/satamv.c =================================================================== --- flashrom-noid_programmers_support_device_list/satamv.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/satamv.c (Arbeitskopie) @@ -29,7 +29,7 @@ uint8_t *mv_bar; uint16_t mv_iobar; -const struct dev_entry satas_mv[] = { +const struct id_dev_entry satas_mv[] = { /* 88SX6041 and 88SX6042 are the same according to the datasheet. */ {0x11ab, 0x7042, OK, "Marvell", "88SX7042 PCI-e 4-port SATA-II"}, Index: flashrom-noid_programmers_support_device_list/dummyflasher.c =================================================================== --- flashrom-noid_programmers_support_device_list/dummyflasher.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/dummyflasher.c (Arbeitskopie) @@ -39,6 +39,11 @@ #include <sys/stat.h> #endif +const struct noid_dev_entry dummy_devs[] = { + {"dummy", OK, "Dummy device, does nothing and logs all accesses"}, + {0}, +}; + #if EMULATE_CHIP static uint8_t *flashchip_contents = NULL; enum emu_chip { Index: flashrom-noid_programmers_support_device_list/internal.c =================================================================== --- flashrom-noid_programmers_support_device_list/internal.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/internal.c (Arbeitskopie) @@ -97,6 +97,11 @@ #endif #if CONFIG_INTERNAL == 1 +const struct noid_dev_entry internal_devs[] = { + {"", OK, "Insert witty remark here and/or reference the board/chipset list\n"}, + {0}, +}; + int force_boardenable = 0; int force_boardmismatch = 0; Index: flashrom-noid_programmers_support_device_list/print_wiki.c =================================================================== --- flashrom-noid_programmers_support_device_list/print_wiki.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/print_wiki.c (Arbeitskopie) @@ -301,7 +301,7 @@ /* Following functions are not needed when no PCI/USB programmers are compiled in, * but since print_wiki code has no size constraints we include it unconditionally. */ -static int count_supported_devs_wiki(const struct dev_entry *devs) +static int count_supported_devs_wiki(const struct id_dev_entry *devs) { unsigned int count = 0; unsigned int i = 0; @@ -309,12 +309,13 @@ count++; return count; } +#warning Handle noid_dev_entry devices static void print_supported_devs_wiki_helper(const struct programmer_entry prog) { int i = 0; static int c = 0; - const struct dev_entry *devs = prog.devs.dev; + const struct id_dev_entry *devs = prog.devs.dev; const unsigned int count = count_supported_devs_wiki(devs); /* Alternate colors if the vendor changes. */ Index: flashrom-noid_programmers_support_device_list/nicintel_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/nicintel_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/nicintel_spi.c (Arbeitskopie) @@ -67,7 +67,7 @@ uint8_t *nicintel_spibar; -const struct dev_entry nics_intel_spi[] = { +const struct id_dev_entry nics_intel_spi[] = { {PCI_VENDOR_ID_INTEL, 0x105e, OK, "Intel", "82571EB Gigabit Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x1076, OK, "Intel", "82541GI Gigabit Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x107c, OK, "Intel", "82541PI Gigabit Ethernet Controller"}, Index: flashrom-noid_programmers_support_device_list/usbblaster_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/usbblaster_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/usbblaster_spi.c (Arbeitskopie) @@ -49,7 +49,7 @@ #define ALTERA_VID 0x09fb #define ALTERA_USBBLASTER_PID 0x6001 -const struct dev_entry devs_usbblasterspi[] = { +const struct id_dev_entry devs_usbblasterspi[] = { {ALTERA_VID, ALTERA_USBBLASTER_PID, OK, "Altera", "USB-Blaster"}, {} Index: flashrom-noid_programmers_support_device_list/nicnatsemi.c =================================================================== --- flashrom-noid_programmers_support_device_list/nicnatsemi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/nicnatsemi.c (Arbeitskopie) @@ -30,7 +30,7 @@ #define BOOT_ROM_ADDR 0x50 #define BOOT_ROM_DATA 0x54 -const struct dev_entry nics_natsemi[] = { +const struct id_dev_entry nics_natsemi[] = { {0x100b, 0x0020, NT, "National Semiconductor", "DP83815/DP83816"}, {0x100b, 0x0022, NT, "National Semiconductor", "DP83820"}, Index: flashrom-noid_programmers_support_device_list/rayer_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/rayer_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/rayer_spi.c (Arbeitskopie) @@ -37,6 +37,12 @@ #include "programmer.h" #include "hwaccess.h" +const struct noid_dev_entry rayer_spi_devs[] = { + {"rayer", OK, "RayeR parallel port programmer"}, + {"xilinx", OK, "Xilinx Parallel Cable III (DLC 5)"}, + {0}, +}; + enum rayer_type { TYPE_RAYER, TYPE_XILINX_DLC5, Index: flashrom-noid_programmers_support_device_list/dediprog.c =================================================================== --- flashrom-noid_programmers_support_device_list/dediprog.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/dediprog.c (Arbeitskopie) @@ -27,6 +27,11 @@ #include "programmer.h" #include "spi.h" +const struct noid_dev_entry dediprog_devs[] = { + {"", OK, "Dediprog SF100"}, + {0}, +}; + #define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 static usb_dev_handle *dediprog_handle; Index: flashrom-noid_programmers_support_device_list/buspirate_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/buspirate_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/buspirate_spi.c (Arbeitskopie) @@ -27,6 +27,11 @@ #include "programmer.h" #include "spi.h" +const struct noid_dev_entry buspirate_spi_devs[] = { + {"", OK, "Dangerous Prototypes Bus Pirate"}, + {0}, +}; + /* Change this to #define if you want to test without a serial implementation */ #undef FAKE_COMMUNICATION Index: flashrom-noid_programmers_support_device_list/linux_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/linux_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/linux_spi.c (Arbeitskopie) @@ -34,6 +34,11 @@ #include "programmer.h" #include "spi.h" +const struct noid_dev_entry linux_spi_devs[] = { + {"", OK, "Device files /dev/spidev*.*"}, + {0}, +}; + static int fd = -1; static int linux_spi_shutdown(void *data); Index: flashrom-noid_programmers_support_device_list/atahpt.c =================================================================== --- flashrom-noid_programmers_support_device_list/atahpt.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/atahpt.c (Arbeitskopie) @@ -33,7 +33,7 @@ #define PCI_VENDOR_ID_HPT 0x1103 -const struct dev_entry ata_hpt[] = { +const struct id_dev_entry ata_hpt[] = { {0x1103, 0x0004, NT, "Highpoint", "HPT366/368/370/370A/372/372N"}, {0x1103, 0x0005, NT, "Highpoint", "HPT372A/372N"}, {0x1103, 0x0006, NT, "Highpoint", "HPT302/302N"}, Index: flashrom-noid_programmers_support_device_list/nic3com.c =================================================================== --- flashrom-noid_programmers_support_device_list/nic3com.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/nic3com.c (Arbeitskopie) @@ -36,7 +36,7 @@ static uint32_t internal_conf; static uint16_t id; -const struct dev_entry nics_3com[] = { +const struct id_dev_entry nics_3com[] = { /* 3C90xB */ {0x10b7, 0x9055, OK, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-TX"}, {0x10b7, 0x9001, NT, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-T4" }, Index: flashrom-noid_programmers_support_device_list/satasii.c =================================================================== --- flashrom-noid_programmers_support_device_list/satasii.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/satasii.c (Arbeitskopie) @@ -30,7 +30,7 @@ static uint8_t *sii_bar; static uint16_t id; -const struct dev_entry satas_sii[] = { +const struct id_dev_entry satas_sii[] = { {0x1095, 0x0680, OK, "Silicon Image", "PCI0680 Ultra ATA-133 Host Ctrl"}, {0x1095, 0x3112, OK, "Silicon Image", "SiI 3112 [SATALink/SATARaid] SATA Ctrl"}, {0x1095, 0x3114, OK, "Silicon Image", "SiI 3114 [SATALink/SATARaid] SATA Ctrl"}, Index: flashrom-noid_programmers_support_device_list/ft2232_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/ft2232_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/ft2232_spi.c (Arbeitskopie) @@ -57,7 +57,7 @@ #define OLIMEX_ARM_OCD_H_PID 0x002B #define OLIMEX_ARM_TINY_H_PID 0x002A -const struct dev_entry devs_ft2232spi[] = { +const struct id_dev_entry devs_ft2232spi[] = { {FTDI_VID, FTDI_FT2232H_PID, OK, "FTDI", "FT2232H"}, {FTDI_VID, FTDI_FT4232H_PID, OK, "FTDI", "FT4232H"}, {FTDI_VID, FTDI_FT232H_PID, OK, "FTDI", "FT232H"}, Index: flashrom-noid_programmers_support_device_list/pony_spi.c =================================================================== --- flashrom-noid_programmers_support_device_list/pony_spi.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/pony_spi.c (Arbeitskopie) @@ -47,6 +47,13 @@ #include "flash.h" #include "programmer.h" +const struct noid_dev_entry pony_spi_devs[] = { + {"serbang", OK, "Programmers compatible with serbang"}, + {"si_prog", OK, "Programmers compatible with SI-Prog"}, + {"ajawe", OK, "Programmers compatible with AJAWe"}, + {0}, +}; + enum pony_type { TYPE_SI_PROG, TYPE_SERBANG, Index: flashrom-noid_programmers_support_device_list/nicintel.c =================================================================== --- flashrom-noid_programmers_support_device_list/nicintel.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/nicintel.c (Arbeitskopie) @@ -27,7 +27,7 @@ uint8_t *nicintel_bar; uint8_t *nicintel_control_bar; -const struct dev_entry nics_intel[] = { +const struct id_dev_entry nics_intel[] = { {PCI_VENDOR_ID_INTEL, 0x1209, NT, "Intel", "8255xER/82551IT Fast Ethernet Controller"}, {PCI_VENDOR_ID_INTEL, 0x1229, OK, "Intel", "82557/8/9/0/1 Ethernet Pro 100"}, Index: flashrom-noid_programmers_support_device_list/flashrom.c =================================================================== --- flashrom-noid_programmers_support_device_list/flashrom.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/flashrom.c (Arbeitskopie) @@ -65,7 +65,7 @@ { .name = "internal", .type = OTHER, - .devs.note = NULL, + .devs.noid_dev = internal_devs, .init = internal_init, .map_flash_region = physmap, .unmap_flash_region = physunmap, @@ -77,8 +77,7 @@ { .name = "dummy", .type = OTHER, - /* FIXME */ - .devs.note = "Dummy device, does nothing and logs all accesses\n", + .devs.noid_dev = dummy_devs, .init = dummy_init, .map_flash_region = dummy_map, .unmap_flash_region = dummy_unmap, @@ -90,7 +89,7 @@ { .name = "nic3com", .type = PCI, - .devs.dev = nics_3com, + .devs.id_dev = nics_3com, .init = nic3com_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -103,7 +102,7 @@ /* This programmer works for Realtek RTL8139 and SMC 1211. */ .name = "nicrealtek", .type = PCI, - .devs.dev = nics_realtek, + .devs.id_dev = nics_realtek, .init = nicrealtek_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -115,7 +114,7 @@ { .name = "nicnatsemi", .type = PCI, - .devs.dev = nics_natsemi, + .devs.id_dev = nics_natsemi, .init = nicnatsemi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -127,7 +126,7 @@ { .name = "gfxnvidia", .type = PCI, - .devs.dev = gfx_nvidia, + .devs.id_dev = gfx_nvidia, .init = gfxnvidia_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -139,7 +138,7 @@ { .name = "drkaiser", .type = PCI, - .devs.dev = drkaiser_pcidev, + .devs.id_dev = drkaiser_pcidev, .init = drkaiser_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -151,7 +150,7 @@ { .name = "satasii", .type = PCI, - .devs.dev = satas_sii, + .devs.id_dev = satas_sii, .init = satasii_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -163,7 +162,7 @@ { .name = "atahpt", .type = PCI, - .devs.dev = ata_hpt, + .devs.id_dev = ata_hpt, .init = atahpt_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -175,7 +174,7 @@ { .name = "ft2232_spi", .type = USB, - .devs.dev = devs_ft2232spi, + .devs.id_dev = devs_ft2232spi, .init = ft2232_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -187,8 +186,7 @@ { .name = "serprog", .type = OTHER, - /* FIXME */ - .devs.note = "All programmer devices speaking the serprog protocol\n", + .devs.noid_dev = serprog_devs, .init = serprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -200,8 +198,7 @@ { .name = "buspirate_spi", .type = OTHER, - /* FIXME */ - .devs.note = "Dangerous Prototypes Bus Pirate\n", + .devs.noid_dev = buspirate_spi_devs, .init = buspirate_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -213,8 +210,7 @@ { .name = "dediprog", .type = OTHER, - /* FIXME */ - .devs.note = "Dediprog SF100\n", + .devs.noid_dev = dediprog_devs, .init = dediprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -226,8 +222,7 @@ { .name = "rayer_spi", .type = OTHER, - /* FIXME */ - .devs.note = "RayeR parallel port programmer\n", + .devs.noid_dev = rayer_spi_devs, .init = rayer_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -239,8 +234,7 @@ { .name = "pony_spi", .type = OTHER, - /* FIXME */ - .devs.note = "Programmers compatible with SI-Prog, serbang or AJAWe\n", + .devs.noid_dev = pony_spi_devs, .init = pony_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -252,7 +246,7 @@ { .name = "nicintel", .type = PCI, - .devs.dev = nics_intel, + .devs.id_dev = nics_intel, .init = nicintel_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -264,7 +258,7 @@ { .name = "nicintel_spi", .type = PCI, - .devs.dev = nics_intel_spi, + .devs.id_dev = nics_intel_spi, .init = nicintel_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -276,7 +270,7 @@ { .name = "ogp_spi", .type = PCI, - .devs.dev = ogp_spi, + .devs.id_dev = ogp_spi, .init = ogp_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -288,7 +282,7 @@ { .name = "satamv", .type = PCI, - .devs.dev = satas_mv, + .devs.id_dev = satas_mv, .init = satamv_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -300,7 +294,7 @@ { .name = "linux_spi", .type = OTHER, - .devs.note = "Device files /dev/spidev*.*\n", + .devs.noid_dev = linux_spi_devs, .init = linux_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -312,7 +306,7 @@ { .name = "usbblaster_spi", .type = USB, - .devs.dev = devs_usbblasterspi, + .devs.id_dev = devs_usbblasterspi, .init = usbblaster_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, @@ -1675,10 +1669,9 @@ case USB: case PCI: case OTHER: - if (p.devs.note == NULL) { - if (strcmp("internal", p.name) == 0) - break; /* This one has its device list stored separately. */ - msg_gerr("Programmer %s has neither a device list nor a textual description!\n", + /* Either id_dev or noid_dev should be non-NULL. */ + if (p.devs.id_dev == NULL) { + msg_gerr("Programmer %s doesn't have a device list!\n", p.name); ret = 1; } Index: flashrom-noid_programmers_support_device_list/programmer.h =================================================================== --- flashrom-noid_programmers_support_device_list/programmer.h (Revision 1666) +++ flashrom-noid_programmers_support_device_list/programmer.h (Arbeitskopie) @@ -99,7 +99,13 @@ OTHER, }; -struct dev_entry { +struct noid_dev_entry { + const char *type; + const enum test_state status; + const char *description; +}; + +struct id_dev_entry { uint16_t vendor_id; uint16_t device_id; const enum test_state status; @@ -111,8 +117,8 @@ const char *name; const enum programmer_type type; union { - const struct dev_entry *const dev; - const char *const note; + const struct noid_dev_entry *const noid_dev; + const struct id_dev_entry *const id_dev; } devs; int (*init) (void); @@ -172,7 +178,7 @@ extern struct pci_access *pacc; int pci_init_common(void); uintptr_t pcidev_readbar(struct pci_dev *dev, int bar); -struct pci_dev *pcidev_init(const struct dev_entry *devs, int bar); +struct pci_dev *pcidev_init(const struct id_dev_entry *devs, int bar); /* rpci_write_* are reversible writes. The original PCI config space register * contents will be restored on shutdown. */ @@ -320,6 +326,7 @@ int register_superio(struct superio s); extern enum chipbustype internal_buses_supported; int internal_init(void); +extern const struct noid_dev_entry internal_devs[]; #endif /* hwaccess.c */ @@ -360,94 +367,97 @@ int dummy_init(void); void *dummy_map(const char *descr, unsigned long phys_addr, size_t len); void dummy_unmap(void *virt_addr, size_t len); +extern const struct noid_dev_entry dummy_devs[]; #endif /* nic3com.c */ #if CONFIG_NIC3COM == 1 int nic3com_init(void); -extern const struct dev_entry nics_3com[]; +extern const struct id_dev_entry nics_3com[]; #endif /* gfxnvidia.c */ #if CONFIG_GFXNVIDIA == 1 int gfxnvidia_init(void); -extern const struct dev_entry gfx_nvidia[]; +extern const struct id_dev_entry gfx_nvidia[]; #endif /* drkaiser.c */ #if CONFIG_DRKAISER == 1 int drkaiser_init(void); -extern const struct dev_entry drkaiser_pcidev[]; +extern const struct id_dev_entry drkaiser_pcidev[]; #endif /* nicrealtek.c */ #if CONFIG_NICREALTEK == 1 int nicrealtek_init(void); -extern const struct dev_entry nics_realtek[]; +extern const struct id_dev_entry nics_realtek[]; #endif /* nicnatsemi.c */ #if CONFIG_NICNATSEMI == 1 int nicnatsemi_init(void); -extern const struct dev_entry nics_natsemi[]; +extern const struct id_dev_entry nics_natsemi[]; #endif /* nicintel.c */ #if CONFIG_NICINTEL == 1 int nicintel_init(void); -extern const struct dev_entry nics_intel[]; +extern const struct id_dev_entry nics_intel[]; #endif /* nicintel_spi.c */ #if CONFIG_NICINTEL_SPI == 1 int nicintel_spi_init(void); -extern const struct dev_entry nics_intel_spi[]; +extern const struct id_dev_entry nics_intel_spi[]; #endif /* ogp_spi.c */ #if CONFIG_OGP_SPI == 1 int ogp_spi_init(void); -extern const struct dev_entry ogp_spi[]; +extern const struct id_dev_entry ogp_spi[]; #endif /* satamv.c */ #if CONFIG_SATAMV == 1 int satamv_init(void); -extern const struct dev_entry satas_mv[]; +extern const struct id_dev_entry satas_mv[]; #endif /* satasii.c */ #if CONFIG_SATASII == 1 int satasii_init(void); -extern const struct dev_entry satas_sii[]; +extern const struct id_dev_entry satas_sii[]; #endif /* atahpt.c */ #if CONFIG_ATAHPT == 1 int atahpt_init(void); -extern const struct dev_entry ata_hpt[]; +extern const struct id_dev_entry ata_hpt[]; #endif /* ft2232_spi.c */ #if CONFIG_FT2232_SPI == 1 int ft2232_spi_init(void); -extern const struct dev_entry devs_ft2232spi[]; +extern const struct id_dev_entry devs_ft2232spi[]; #endif /* usbblaster_spi.c */ #if CONFIG_USBBLASTER_SPI == 1 int usbblaster_spi_init(void); -extern const struct dev_entry devs_usbblasterspi[]; +extern const struct id_dev_entry devs_usbblasterspi[]; #endif /* rayer_spi.c */ #if CONFIG_RAYER_SPI == 1 int rayer_spi_init(void); +extern const struct noid_dev_entry rayer_spi_devs[]; #endif /* pony_spi.c */ #if CONFIG_PONY_SPI == 1 int pony_spi_init(void); +extern const struct noid_dev_entry pony_spi_devs[]; #endif /* bitbang_spi.c */ @@ -456,16 +466,19 @@ /* buspirate_spi.c */ #if CONFIG_BUSPIRATE_SPI == 1 int buspirate_spi_init(void); +extern const struct noid_dev_entry buspirate_spi_devs[]; #endif /* linux_spi.c */ #if CONFIG_LINUX_SPI == 1 int linux_spi_init(void); +extern const struct noid_dev_entry linux_spi_devs[]; #endif /* dediprog.c */ #if CONFIG_DEDIPROG == 1 int dediprog_init(void); +extern const struct noid_dev_entry dediprog_devs[]; #endif /* flashrom.c */ @@ -642,6 +655,7 @@ #if CONFIG_SERPROG == 1 int serprog_init(void); void serprog_delay(int usecs); +extern const struct noid_dev_entry serprog_devs[]; #endif /* serial.c */ Index: flashrom-noid_programmers_support_device_list/print.c =================================================================== --- flashrom-noid_programmers_support_device_list/print.c (Revision 1666) +++ flashrom-noid_programmers_support_device_list/print.c (Arbeitskopie) @@ -433,11 +433,11 @@ } #endif -void print_supported_devs(const struct programmer_entry prog, const char *const type) +void print_supported_id_devs(const struct programmer_entry prog, const char *const type) { int i; - const struct dev_entry *const devs = prog.devs.dev; + const struct id_dev_entry *const devs = prog.devs.id_dev; msg_ginfo("\nSupported %s devices for the %s programmer:\n", type, prog.name); for (i = 0; devs[i].vendor_name != NULL; i++) { msg_pinfo("%s %s [%04x:%04x]%s\n", devs[i].vendor_name, devs[i].device_name, devs[i].vendor_id, @@ -445,6 +445,18 @@ } } +void print_supported_noid_devs(const struct programmer_entry prog, const char *const type) +{ + int i; + + const struct noid_dev_entry *const devs = prog.devs.noid_dev; + msg_ginfo("\nSupported models for the %s programmer:\n", prog.name); + for (i = 0; devs[i].type != NULL; i++) { + msg_pinfo("%-20s %s %s\n", devs[i].type, devs[i].description, + (devs[i].status == NT) ? " (untested)" : ""); + } +} + int print_supported(void) { unsigned int i; @@ -467,18 +479,15 @@ const struct programmer_entry prog = programmer_table[i]; switch (prog.type) { case USB: - print_supported_devs(prog, "USB"); + print_supported_id_devs(prog, "USB"); break; #if NEED_PCI == 1 case PCI: - print_supported_devs(prog, "PCI"); + print_supported_id_devs(prog, "PCI"); break; #endif case OTHER: - if (prog.devs.note != NULL) { - msg_ginfo("\nSupported devices for the %s programmer:\n", prog.name); - msg_ginfo("%s", prog.devs.note); - } + print_supported_noid_devs(prog, "(generic)"); break; default: msg_gerr("\n%s: %s: Uninitialized programmer type! Please report a bug at " -- http://www.hailfinger.org/

2 6

[PATCH] Don't build atapromise on libpayload
by Carl-Daniel Hailfinger 28 Feb '16

28 Feb '16

libpayload struct pci_dev is missing a member named 'rom_size' needed by atapromise. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-atapromise_disable_on_libpayload/Makefile =================================================================== --- flashrom-atapromise_disable_on_libpayload/Makefile (Revision 1943) +++ flashrom-atapromise_disable_on_libpayload/Makefile (Arbeitskopie) @@ -320,6 +320,11 @@ else override CONFIG_DEDIPROG = no endif +ifeq ($(CONFIG_ATAPROMISE), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAPROMISE=yes +else +override CONFIG_ATAPROMISE = no +endif ifeq ($(CONFIG_FT2232_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes else

2 6

[commit] r1946 - trunk
by repository service 28 Feb '16

28 Feb '16

Author: hailfinger Date: Sun Feb 28 23:04:51 2016 New Revision: 1946 URL: http://flashrom.org/trac/flashrom/changeset/1946 Log: Makefile: Fix driver blacklist dependencies Allow mstarddc_spi and pony_spi on Android. Allow mstarddc_spi and pony_spi on architectures with unsupported raw access. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sun Feb 28 18:04:38 2016 (r1945) +++ trunk/Makefile Sun Feb 28 23:04:51 2016 (r1946) @@ -343,6 +343,8 @@ endif ifneq ($(TARGET_OS), Linux) +# Android is handled internally as separate OS, but it supports CONFIG_LINUX_SPI and CONFIG_MSTARDDC_SPI +ifneq ($(TARGET_OS), Android) ifeq ($(CONFIG_LINUX_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_LINUX_SPI=yes else @@ -354,6 +356,7 @@ override CONFIG_MSTARDDC_SPI = no endif endif +endif ifeq ($(TARGET_OS), Android) # Android on x86 (currently) does not provide raw PCI port I/O operations @@ -428,11 +431,6 @@ else override CONFIG_RAYER_SPI = no endif -ifeq ($(CONFIG_PONY_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes -else -override CONFIG_PONY_SPI = no -endif ifeq ($(CONFIG_NIC3COM), yes) UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes else @@ -463,11 +461,6 @@ else override CONFIG_ATAPROMISE = no endif -ifeq ($(CONFIG_MSTARDDC_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_MSTARDDC_SPI=yes -else -override CONFIG_MSTARDDC_SPI = no -endif ifeq ($(CONFIG_DRKAISER), yes) UNSUPPORTED_FEATURES += CONFIG_DRKAISER=yes else

1 0

Device revision 4.03
by Meikel 28 Feb '16

28 Feb '16

Hey, if you are still looking for the device with revision 4.03, currently got a PM25L0032 in my prommer reporting this revision: Manufacturer ID: 7f Memory Type: 9d46 Capacity: 46 Chip capacity is 64 All the best Meikel

2 1

Re: [flashrom] New programmer board "SPI_TT LPT" support - patch submission
by Stefan Tauner 28 Feb '16

28 Feb '16

On Sun, 28 Feb 2016 22:17:32 +0300 Max <flammaden(a)gmail.com> wrote: > The circuit power is totally on ham choice. Usually, 5V from USB or PC PSU > molex and LDO for 3.3V + some cap ~10mF after it. Everything's clear now, thanks. > If previous image is copyrighted, I have another one. :) > If you did not draw it yourself or the author gave his permission in form of an appropriate license you are not allowed to publish *any* picture - and we are not allowed to host them for the public in our mailing list archive either... -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] New programmer board "SPI_TT LPT" support - patch submission
by Stefan Tauner 28 Feb '16

28 Feb '16

On Sun, 28 Feb 2016 15:27:09 +0300 Max <flammaden(a)gmail.com> wrote: > SPI read was tested. Write wasn't, because of sudden AC voltage blackout > and I haven't had any more effort going to collecting build tools and > struggling with build process. > It's buffer enable pin is hardwired, so no control required. Ok, thanks! I have committed a variation of your patch in r1945 but left the status as untested. > > In attachment there are SPI-TT schematics, so you can add it to man page. That's easily discoverable (and copyrighted) so we won't include it. However, I was not able to find out how the circuit is powered (most information sources are in russian and translating them automatically was not enough to find out :). I presume Vcc is connected to an external power source, right? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

[commit] r1945 - trunk
by repository service 28 Feb '16

28 Feb '16

Author: stefanct Date: Sun Feb 28 18:04:38 2016 New Revision: 1945 URL: http://flashrom.org/trac/flashrom/changeset/1945 Log: rayer_spi: add support for SPI Tiny Tools-compatible hardware. Apparently, there is at least one board of Russian origin (coined SPI_TT LPT) that works with SPI Tiny Tools which is a closed-source Windows GUI program somewhat similar to flashrom. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/flashrom.8.tmpl trunk/rayer_spi.c Modified: trunk/flashrom.8.tmpl ============================================================================== --- trunk/flashrom.8.tmpl Sat Feb 27 00:51:21 2016 (r1944) +++ trunk/flashrom.8.tmpl Sun Feb 28 18:04:38 2016 (r1945) @@ -899,7 +899,8 @@ .B model can be .BR rayer " for the RayeR cable, " byteblastermv " for the Altera ByteBlasterMV, " stk200 " for the Atmel \ -STK200/300, " wiggler " for the Macraigor Wiggler, or " xilinx " for the Xilinx Parallel Cable III (DLC 5)." +STK200/300, " wiggler " for the Macraigor Wiggler, " xilinx " for the Xilinx Parallel Cable III (DLC 5), or" \ +" spi_tt" " for SPI Tiny Tools-compatible hardware. .sp More information about the RayeR hardware is available at .nh Modified: trunk/rayer_spi.c ============================================================================== --- trunk/rayer_spi.c Sat Feb 27 00:51:21 2016 (r1944) +++ trunk/rayer_spi.c Sun Feb 28 18:04:38 2016 (r1945) @@ -106,12 +106,20 @@ .miso_bit = 7, }; +static const struct rayer_pinout spi_tt = { + .cs_bit = 2, + .sck_bit = 0, + .mosi_bit = 4, + .miso_bit = 7, +}; + static const struct rayer_programmer rayer_spi_types[] = { {"rayer", NT, "RayeR SPIPGM", &rayer_spipgm}, {"xilinx", NT, "Xilinx Parallel Cable III (DLC 5)", &xilinx_dlc5}, {"byteblastermv", OK, "Altera ByteBlasterMV", &altera_byteblastermv}, {"stk200", NT, "Atmel STK200/300 adapter", &atmel_stk200}, {"wiggler", OK, "Wiggler LPT", &wiggler_lpt}, + {"spi_tt", NT, "SPI Tiny Tools (SPI_TT LPT)", &spi_tt}, {0}, };

1 0

Re: [flashrom] New programmer board "SPI_TT LPT" support - patch submission
by Stefan Tauner 28 Feb '16

28 Feb '16

On Sun, 28 Feb 2016 11:03:19 +0300 Max <flammaden(a)gmail.com> wrote: > Hello, Stefan! > > Actually, I doesn't real Linux C programmer - I just passed by. :) > So, I just tried to get into this area, but get very distracted by > wretchedness and inconvenience of Linux development tools. I don't think > there's will be next time. :) I just "threw patch away", hoping that this > programmer widely enough available and somebody, having proper skills, > finishes it. Seems to be, my thoughts was wrong, but till now I don't be > sad. > Now I surprised! Thank you for your precious time to finish this patch, > Stefan! > > I marked them as untested because I think that my one working quick dirty > patch is not an reliable proof of testing. The patch alone is no proof but if you have tested it with real hardware and it worked then there is no reason to not believe you and mark it as tested. Have you run flashrom with your patch on that hardware and did writing work? > It doesn't need any enable routine - it has no logic, no triggers/relay - > just resistors and buffer. Buffers most often have disable (or enable) pins and if they are not pulled down (or up) statically by resistors we need to do that dynamically when starting to access the programmer. This would not be unusual at all for this class of programmers... hence my question. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] New programmer board "SPI_TT LPT" support - patch submission
by Stefan Tauner 28 Feb '16

28 Feb '16

On Tue, 4 Aug 2015 11:12:08 +0300 Max <flammaden(a)gmail.com> wrote: > Hello, everybody, involved into flashrom! > > I'd implemented support for well known in Russia SPI_TT LPT programmer. > Basically, it's only Byteblaster clone with changed pinout. So, > modifications was pretty straIghtforward. > > In attach - modified "rayer_spi.c" from trunk branch. > Hope, it will be useful for someone. Hi Max, thanks for your contribution! Please post a proper patch according to our development guidelines next time: https://www.flashrom.org/Development_Guidelines I have prepared a patch as you suggested and even included an entry to the manpage. However, I wonder if you have tested your file successfully because the tested field was set to NT instead of OK. Also, doesn't it need any enable routine like the byteblaster? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

[PATCH] Add support for GD25VQ21B, GD25VQ40C, GD25VQ80C and GD25VQ16C
by Hatim Kanchwala 28 Feb '16

28 Feb '16

Signed-off-by: Hatim Kanchwala <hatim(a)hatimak.me> --- flashchips.c | 163 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 5 +- 2 files changed, 167 insertions(+), 1 deletion(-) diff --git a/flashchips.c b/flashchips.c index 238389b..eb6eacb 100644 --- a/flashchips.c +++ b/flashchips.c @@ -6285,26 +6285,66 @@ const struct flashchip flashchips[] = { .eraseblocks = { {1024 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", + .name = "GD25VQ21B", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ21B, + .total_size = 256, + .page_size = 256, + /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 8} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd Status Register; read 0x35 */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", .name = "GD25VQ41B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25VQ41B, .total_size = 512, .page_size = 256, /* OTP: 1536B total; read 0x48, write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = { @@ -6324,26 +6364,149 @@ const struct flashchip flashchips[] = { .eraseblocks = { {512 * 1024, 1} }, .block_erase = spi_block_erase_c7, } }, /* TODO: 2nd Status Register; read 0x35 */ .printlock = spi_prettyprint_status_register_bp4_srwd, .unlock = spi_disable_blockprotect_bp4_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2300, 3600}, }, { + .vendor = "GigaDevice", + .name = "GD25VQ40C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ41B, + .total_size = 512, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd Status Register; read 0x35 */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ80C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ80C, + .total_size = 1024, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 256} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 32} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd Status Register; read 0x35 */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { + .vendor = "GigaDevice", + .name = "GD25VQ16C", + .bustype = BUS_SPI, + .manufacture_id = GIGADEVICE_ID, + .model_id = GIGADEVICE_GD25VQ16C, + .total_size = 2 * 1024, + .page_size = 256, + /* Supports SFDP; read 0x5A */ + /* OTP: 1024B total; read 0x48, write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { { 4 * 1024, 512} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { { 32 * 1024, 64} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { { 64 * 1024, 32} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: 2nd Status Register; read 0x35 */ + .printlock = spi_prettyprint_status_register_bp4_srwd, + .unlock = spi_disable_blockprotect_bp4_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ + .voltage = {2300, 3600}, + }, + + { .vendor = "Hyundai", .name = "HY29F002T", .bustype = BUS_PARALLEL, .manufacture_id = HYUNDAI_ID, .model_id = HYUNDAI_HY29F002T, .total_size = 256, .page_size = 256 * 1024, .feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */ .tested = TEST_OK_PRE, .probe = probe_jedec, .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ .block_erasers = { diff --git a/flashchips.h b/flashchips.h index a109e94..ac1901f 100644 --- a/flashchips.h +++ b/flashchips.h @@ -368,27 +368,30 @@ #define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25QB */ #define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25QB */ #define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */ #define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */ #define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ #define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ #define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B and GD25Q128C only, can be distinguished by SFDP */ #define GIGADEVICE_GD25LQ40 0x6013 #define GIGADEVICE_GD25LQ80 0x6014 #define GIGADEVICE_GD25LQ16 0x6015 #define GIGADEVICE_GD25LQ32 0x6016 #define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */ #define GIGADEVICE_GD25LQ128 0x6018 -#define GIGADEVICE_GD25VQ41B 0x4213 +#define GIGADEVICE_GD25VQ21B 0x4212 +#define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ +#define GIGADEVICE_GD25VQ80C 0x4214 +#define GIGADEVICE_GD25VQ16C 0x4215 #define GIGADEVICE_GD29GL064CAB 0x7E0601 #define HYUNDAI_ID 0xAD /* Hyundai */ #define HYUNDAI_HY29F400T 0x23 /* Same as HY29F400AT */ #define HYUNDAI_HY29F800B 0x58 /* Same as HY29F800AB */ #define HYUNDAI_HY29LV800B 0x5B #define HYUNDAI_HY29F040A 0xA4 #define HYUNDAI_HY29F400B 0xAB /* Same as HY29F400AB */ #define HYUNDAI_HY29F002B 0x34 #define HYUNDAI_HY29F002T 0xB0 #define HYUNDAI_HY29LV400T 0xB9 #define HYUNDAI_HY29LV400B 0xBA #define HYUNDAI_HY29F080 0xD5 -- Regards, Hatim Kanchwala http://hatimak.me B. Tech. Electrical Engineering Indian Institute of Technology Patna

3 2

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom