flashrom June 2011

flashrom@flashrom.org

50 participants
297 discussions

Re: [flashrom] [PATCH 2/2] add board enable for GA-8IP775
by Uwe Hermann 13 Jun '11

13 Jun '11

On Sun, Jun 12, 2011 at 05:38:23PM +0200, Stefan Tauner wrote: > {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, P3, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, > + {0x8086, 0x2570, 0x1458, 0x2570, 0x8086, 0x24d0, 0, 0, "^8IP775/-G$",NULL, NULL, P3, "Gigabyte", "GA-8IP775", 0, OK, intel_ich_gpio32_raise}, Gigabyte -> GIGABYTE, as in the other entries please. Other than that the patch is: Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> For archival purposes, here's the full pastebin.com from above (which may disappear at some point): flashrom v0.9.3-r1297 on Linux 2.6.32-5-686 (i686), built with libpci 3.1.7, GCC 4.4.5, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "Intel ICH5/ICH5R", enabling flash write... OK. This chipset supports the following protocols: FWH. Disabling flash write protection for board "Gigabyte GA-8IP775"... OK. Found chip "PMC Pm49FL002" (256 KB, LPC,FWH) at physical address 0xfffc0000. === This flash part has status UNTESTED for operations: WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Flash image seems to be a legacy BIOS. Disabling checks. Erasing and writing flash chip... Done. Verifying flash... VERIFIED. Uwe. -- http://hermann-uwe.de | http://sigrok.org http://randomprojects.org | http://unmaintained-free-software.org

2 1

[commit] r1337 - trunk
by repository service 13 Jun '11

13 Jun '11

Author: stefanct Date: Mon Jun 13 18:59:01 2011 New Revision: 1337 URL: http://flashrom.org/trac/flashrom/changeset/1337 Log: add board enable for GA-8IP775 - logs before: http://paste.flashrom.org/view.php?id=565 - success: http://www.flashrom.org/pipermail/flashrom/2011-June/006747.html Signed-off-by: Joshua Roys <roysjosh(a)gmail.com> Signed-off-by: Idwer Vollering <vidwer(a)gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Mon Jun 13 18:58:54 2011 (r1336) +++ trunk/board_enable.c Mon Jun 13 18:59:01 2011 (r1337) @@ -1580,6 +1580,7 @@ /* * Suited for: * - P4SD-LA (HP OEM): i865 + ICH5 + * - GIGABYTE GA-8IP775: 865P + ICH5 * - GIGABYTE GA-8PE667 Ultra 2: socket 478 + i845PE + ICH4 * - MSI MS-6788-40 (aka 848P Neo-V) */ @@ -2020,6 +2021,7 @@ {0x10de, 0x02f0, 0x105b, 0x0d01, 0x10de, 0x0264, 0x105b, 0x0d01, NULL, NULL, NULL, P3, "Foxconn", "6150K8MD-8EKRSH", 0, NT, nvidia_mcp_gpio2_raise}, {0x8086, 0x2443, 0x8086, 0x2442, 0x8086, 0x1130, 0x8086, 0x1130, "^6IEM ", NULL, NULL, P3, "GIGABYTE", "GA-6IEM", 0, NT, intel_ich_gpio25_raise}, {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, P3, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, + {0x8086, 0x2570, 0x1458, 0x2570, 0x8086, 0x24d0, 0, 0, "^8IP775/-G$",NULL, NULL, P3, "GIGABYTE", "GA-8IP775", 0, OK, intel_ich_gpio32_raise}, {0x8086, 0x244b, 0x8086, 0x2442, 0x8086, 0x2445, 0x1458, 0xa002, NULL, NULL, NULL, P3, "GIGABYTE", "GA-8IRML", 0, OK, intel_ich_gpio25_raise}, {0x8086, 0x24c3, 0x1458, 0x24c2, 0x8086, 0x24cd, 0x1458, 0x5004, NULL, NULL, NULL, P3, "GIGABYTE", "GA-8PE667 Ultra 2", 0, OK, intel_ich_gpio32_raise}, {0x10DE, 0x02F1, 0x1458, 0x5000, 0x10DE, 0x0261, 0x1458, 0x5001, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8N51GMF", 0, OK, nvidia_mcp_gpio3b_raise}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Mon Jun 13 18:58:54 2011 (r1336) +++ trunk/print.c Mon Jun 13 18:59:01 2011 (r1337) @@ -515,6 +515,7 @@ B("GIGABYTE", "GA-7DXR", 1, "http://www.gigabyte.de/Products/Motherboard/Products_Spec.aspx?ProductID=13…", NULL), B("GIGABYTE", "GA-7VT600", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1666", NULL), B("GIGABYTE", "GA-7ZM", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1366", "Works fine if you remove jumper JP9 on the board and disable the flash protection BIOS option."), + B("GIGABYTE", "GA-8IP775", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1830", NULL), B("GIGABYTE", "GA-8IRML", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1343", NULL), B("GIGABYTE", "GA-8PE667 Ultra 2", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1607", NULL), B("GIGABYTE", "GA-965P-DS4", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2288", NULL),

1 0

Success: GA-965GM-S2 (rev. 2.0)
by Joshua Malcolm 13 Jun '11

13 Jun '11

flashrom -V http://paste.flashrom.org/view.php?id=605 Mobo is http://www.gigabyte.com/products/product-page.aspx?pid=2617#sp Thanks flashrom!

3 2

[commit] r1335 - trunk
by repository service 12 Jun '11

12 Jun '11

Author: stefanct Date: Sun Jun 12 21:47:55 2011 New Revision: 1335 URL: http://flashrom.org/trac/flashrom/changeset/1335 Log: add a bunch of new/tested motherboards, board/chipset enables and flash chips etc 3 - mark AT25DF321 as fully tested http://www.flashrom.org/pipermail/flashrom/attachments/20110527/01f1868b/at… - mark 82802AB as fully tested http://www.flashrom.org/pipermail/flashrom/2011-April/006145.html - mark Pm49FL002 as fully tested http://pastebin.com/pb5NTCmW - add Supermicro X8DT3 to boards_known http://www.flashrom.org/pipermail/flashrom/attachments/20110527/01f1868b/at… - add Supermicro X5DP8-G2 to boards_known http://www.flashrom.org/pipermail/flashrom/2011-April/006145.html - add Supermicro X8SIE as NOT WORKING to boards_known http://www.flashrom.org/pipermail/flashrom/2011-May/006554.html - add a DMI search pattern for the ASUS A8N-SLI Deluxe board enable to mitigate misdetections http://www.flashrom.org/pipermail/flashrom/2010-August/004379.html http://www.flashrom.org/pipermail/flashrom/2011-May/006570.html also, fix some random white space errors and comments/strings Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/board_enable.c trunk/chipset_enable.c trunk/flash.h trunk/flashchips.c trunk/print.c trunk/print_wiki.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/board_enable.c Sun Jun 12 21:47:55 2011 (r1335) @@ -1980,7 +1980,7 @@ {0x1002, 0x4372, 0x103c, 0x2a26, 0x1002, 0x4377, 0x103c, 0x2a26, NULL, NULL, NULL, P3, "ASUS", "A8AE-LE", 0, OK, amd_sbxxx_gpio9_raise}, {0x8086, 0x27A0, 0x1043, 0x1287, 0x8086, 0x27DF, 0x1043, 0x1287, "^A8J", NULL, NULL, P3, "ASUS", "A8Jm", 0, NT, intel_ich_gpio34_raise}, {0x10DE, 0x0260, 0x103c, 0x2a3e, 0x10DE, 0x0264, 0x103c, 0x2a3e, "NAGAMI2L", NULL, NULL, P3, "ASUS", "A8N-LA (Nagami-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, - {0x10DE, 0x005E, 0x1043, 0x815A, 0x10DE, 0x0054, 0x1043, 0x815A, NULL, NULL, NULL, P3, "ASUS", "A8N", 0, NT, board_shuttle_fn25}, /* TODO: This should probably be A8N-SLI Deluxe, see http://www.coreboot.org/pipermail/flashrom/2009-November/000878.html. */ + {0x10DE, 0x005E, 0x1043, 0x815A, 0x10DE, 0x0054, 0x1043, 0x815A, "^A8N-SLI", NULL, NULL, P3, "ASUS", "A8N-SLI Deluxe", 0, NT, board_shuttle_fn25}, {0x10de, 0x0264, 0x1043, 0x81bc, 0x10de, 0x02f0, 0x1043, 0x81cd, NULL, NULL, NULL, P3, "ASUS", "A8N-VM CSM", 0, NT, w83627ehf_gpio24_raise_2e}, {0x10DE, 0x0264, 0x1043, 0x81C0, 0x10DE, 0x0260, 0x1043, 0x81C0, NULL, NULL, NULL, P3, "ASUS", "M2NBP-VM CSM", 0, OK, nvidia_mcp_gpio0_raise}, {0x1106, 0x1336, 0x1043, 0x80ed, 0x1106, 0x3288, 0x1043, 0x8249, NULL, NULL, NULL, P3, "ASUS", "M2V-MX", 0, OK, via_vt823x_gpio5_raise}, Modified: trunk/chipset_enable.c ============================================================================== --- trunk/chipset_enable.c Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/chipset_enable.c Sun Jun 12 21:47:55 2011 (r1335) @@ -1082,12 +1082,12 @@ {0x8086, 0x7000, OK, "Intel", "PIIX3", enable_flash_piix4}, {0x8086, 0x7110, OK, "Intel", "PIIX4/4E/4M", enable_flash_piix4}, {0x8086, 0x122e, OK, "Intel", "PIIX", enable_flash_piix4}, - {0x8086, 0x8119, OK, "Intel", "Poulsbo", enable_flash_poulsbo}, - {0x10de, 0x0030, OK, "NVIDIA", "nForce4/MCP4", enable_flash_nvidia_nforce2}, + {0x8086, 0x8119, OK, "Intel", "Poulsbo", enable_flash_poulsbo}, + {0x10de, 0x0030, OK, "NVIDIA", "nForce4/MCP4", enable_flash_nvidia_nforce2}, {0x10de, 0x0050, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* LPC */ {0x10de, 0x0051, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* Pro */ - {0x10de, 0x0060, OK, "NVIDIA", "NForce2", enable_flash_nvidia_nforce2}, - {0x10de, 0x00e0, OK, "NVIDIA", "NForce3", enable_flash_nvidia_nforce2}, + {0x10de, 0x0060, OK, "NVIDIA", "NForce2", enable_flash_nvidia_nforce2}, + {0x10de, 0x00e0, OK, "NVIDIA", "NForce3", enable_flash_nvidia_nforce2}, /* Slave, should not be here, to fix known bug for A01. */ {0x10de, 0x00d3, OK, "NVIDIA", "CK804", enable_flash_ck804}, {0x10de, 0x0260, NT, "NVIDIA", "MCP51", enable_flash_ck804}, Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/flash.h Sun Jun 12 21:47:55 2011 (r1335) @@ -133,7 +133,7 @@ */ struct block_eraser { struct eraseblock{ - unsigned int size; /* Eraseblock size */ + unsigned int size; /* Eraseblock size in bytes */ unsigned int count; /* Number of contiguous blocks with that size */ } eraseblocks[NUM_ERASEREGIONS]; /* a block_erase function should try to erase one block of size Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/flashchips.c Sun Jun 12 21:47:55 2011 (r1335) @@ -1495,7 +1495,7 @@ .total_size = 4096, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_OK_PRE, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -3727,7 +3727,7 @@ .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_82802ab, .probe_timing = TIMING_IGNORED, /* routine does not use probe_timing (82802ab.c) */ .block_erasers = @@ -5065,7 +5065,7 @@ .total_size = 256, .page_size = 16 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, - .tested = TEST_OK_PRE, + .tested = TEST_OK_PREW, .probe = probe_jedec, .probe_timing = TIMING_ZERO, /* routine is wrapper to probe_jedec (pm49fl00x.c) */ .block_erasers = Modified: trunk/print.c ============================================================================== --- trunk/print.c Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/print.c Sun Jun 12 21:47:55 2011 (r1335) @@ -535,7 +535,7 @@ B("GIGABYTE", "GA-MA790FX-DQ6", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2690", NULL), B("GIGABYTE", "GA-MA790GP-DS4H", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2887", NULL), B("GIGABYTE", "GA-MA790XT-UD4P (rev. 1.0)", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=3010", NULL), - B("GIGABYTE", "GA-P55A-UD4 (rev. 1.0 (and 2.0?))", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=3436", NULL), + B("GIGABYTE", "GA-P55A-UD4 (rev. 1.0)", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=3436", NULL), B("HP", "e-Vectra P2706T", 1, "http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&pro…", NULL), B("HP", "ProLiant DL145 G3", 1, "http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c008…", NULL), B("HP", "ProLiant DL165 G6", 1, "http://h10010.www1.hp.com/wwpc/us/en/sm/WF05a/15351-15351-3328412-241644-33…", NULL), @@ -619,9 +619,12 @@ B("Sun", "Fire x4540", 0, "http://www.sun.com/servers/x64/x4540/", "No public report found. May work now."), B("Sun", "Fire x4600", 0, "http://www.sun.com/servers/x64/x4600/", "No public report found. May work now."), B("Supermicro", "H8QC8", 1, "http://www.supermicro.com/Aplus/motherboard/Opteron/nforce/H8QC8.cfm", NULL), + B("Supermicro", "X5DP8-G2", 1, "http://www.supermicro.com/products/motherboard/Xeon/E7501/X5DP8-G2.cfm", NULL), + B("Supermicro", "X8DT3", 1, "http://www.supermicro.com/products/motherboard/QPI/5500/X8DT3.cfm", NULL), B("Supermicro", "X8DTH-6F", 1, "http://www.supermicro.com/products/motherboard/QPI/5500/X8DTH-6F.cfm", NULL), B("Supermicro", "X8DTT-F", 1, "http://www.supermicro.com/products/motherboard/QPI/5500/X8DTT-F.cfm", NULL), B("Supermicro", "X8DTU-F", 1, "http://www.supermicro.com/products/motherboard/QPI/5500/X8DTU-F.cfm", NULL), + B("Supermicro", "X8SIE", 0, "http://www.supermicro.com/products/motherboard/Xeon3000/3400/X8SIE.cfm?IPMI…", "Does not work with 0.9.2; see http://www.flashrom.org/pipermail/flashrom/2011-May/006554.html May work now, but please consult us before trying."), B("Supermicro", "X8STi", 1, "http://www.supermicro.com/products/motherboard/Xeon3000/X58/X8STi.cfm", NULL), B("T-Online", "S-100", 1, "http://wiki.freifunk-hannover.de/T-Online_S_100", NULL), B("Tekram", "P6Pro-A5", 1, "http://www.motherboard.cz/mb/tekram/P6Pro-A5.htm", NULL), Modified: trunk/print_wiki.c ============================================================================== --- trunk/print_wiki.c Sun Jun 12 10:14:10 2011 (r1334) +++ trunk/print_wiki.c Sun Jun 12 21:47:55 2011 (r1335) @@ -52,9 +52,9 @@ make flashrom work (given flashrom supports the respective chipset and flash \ chip), or that they do not yet work at all. If they do not work, support may \ or may not be added later.\n\n\ -Mainboards which don't appear in the list may or may not work (we don't \ -know, someone has to give it a try). Please report any further verified \ -mainboards on the [[Mailinglist|mailing list]].\n"; +Mainboards (or individual revisions) which don't appear in the list may or may \ +not work (we don't know, someone has to give it a try). Please report any \ +further verified mainboards on the [[Mailinglist|mailing list]].\n"; #endif static const char chip_th[] = "{| border=\"0\" style=\"font-size: smaller\" \

1 0

Supermicro success (X8DT3) and failure/bricking (X8SIE).
by Bill Broadley 12 Jun '11

12 Jun '11

First the success. I upgraded the BIOS on a Supermicro X8DT3 without problem. I upgraded it to version 2.0a of the BIOS with a release date of 09/14/2010. I was asked to send a flashrom -V, attached. The bad news, my Supermicro X8SIE completely bricked. During the flash: # flashrom -w x8sie0.527 flashrom v0.9.2-r1141 on Linux 2.6.38-8-generic (x86_64), built with libpci 3.1.7, GCC 4.5.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "Intel 3420", enabling flash write... OK. This chipset supports the following protocols: FWH,SPI. Found chip "Atmel AT25DF321" (4096 KB, SPI) at physical address 0xffc00000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash before programming... Erasing flash chip... spi_block_erase_20 failed during command execution at address 0x0 spi_block_erase_52 failed during command execution at address 0x0 Verification impossible because read failed at 0x1000 (len 0x100) ERASE FAILED! spi_chip_erase_60 failed during command execution Verification impossible because read failed at 0x1000 (len 0x100) ERASE FAILED! FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! I tried to read the image to see if I could tell if it was either the old ROM or the new: flashrom -r old-unknown.rom Reading flash... Read operation failed! FAILED. Found chipset "Intel 3420", enabling flash write... OK. This chipset supports the following protocols: FWH,SPI. Found chip "Atmel AT25DF321" (4096 KB, SPI) at physical address 0xffc00000. I found a rather promising mention in the manual of taking a USB key and copying the BIOS image (x8sie0.527 in this case) to super.rom then hold down <Ctrl> and <Home> simultaneously during bootup. Said system turns on, network lights come on, motherboard controlled fans come up. The USB's devices LEDs however never light. I suspect it's a loss, but I'm open to suggestions. If I do replace it I'll get another LGA1156 single socket server motherboard. Any motherboard that's known to work with flashrom would be a bonus.

2 1

Success: Intel 82802AB on Supermicro X5DP8-G2 (chipset Intel ICH3-S/Intel E7501)
by Gerard Krol 12 Jun '11

12 Jun '11

Just a quick note to report success in flashing my bios using flashrom. Mainboard: Supermicro X5DP8-G2 Chipset: Intel E7501 (Intel ICH3-S) Flash Chip (reported by flashrom): Intel 82802AB I had to cut the rom to the correct size using dd if=ORIGNAL.ROM of=new.rom bs=512k count=1 I did a -r and then a -w, no errors. No other options were used. The bios complained about a wrong CMOS checksum after reboot so it loaded default settings. Regards, Gerard

2 1

[PATCH 2/2] add board enable for GA-8IP775
by Stefan Tauner 12 Jun '11

12 Jun '11

- logs before: http://paste.flashrom.org/view.php?id=565 - success: http://pastebin.com/pb5NTCmW Signed-off-by: Joshua Roys <roysjosh(a)gmail.com> Signed-off-by: Idwer Vollering <vidwer(a)gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- board_enable.c | 2 ++ print.c | 1 + 2 files changed, 3 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index a41f18d..e8e337c 100644 --- a/board_enable.c +++ b/board_enable.c @@ -1580,6 +1580,7 @@ static int intel_ich_gpio26_raise(void) /* * Suited for: * - P4SD-LA (HP OEM): i865 + ICH5 + * - GIGABYTE GA-8IP775: 865P + ICH5 * - GIGABYTE GA-8PE667 Ultra 2: socket 478 + i845PE + ICH4 * - MSI MS-6788-40 (aka 848P Neo-V) */ @@ -2020,6 +2021,7 @@ const struct board_pciid_enable board_pciid_enables[] = { {0x10de, 0x02f0, 0x105b, 0x0d01, 0x10de, 0x0264, 0x105b, 0x0d01, NULL, NULL, NULL, P3, "Foxconn", "6150K8MD-8EKRSH", 0, NT, nvidia_mcp_gpio2_raise}, {0x8086, 0x2443, 0x8086, 0x2442, 0x8086, 0x1130, 0x8086, 0x1130, "^6IEM ", NULL, NULL, P3, "GIGABYTE", "GA-6IEM", 0, NT, intel_ich_gpio25_raise}, {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, P3, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, + {0x8086, 0x2570, 0x1458, 0x2570, 0x8086, 0x24d0, 0, 0, "^8IP775/-G$",NULL, NULL, P3, "Gigabyte", "GA-8IP775", 0, OK, intel_ich_gpio32_raise}, {0x8086, 0x244b, 0x8086, 0x2442, 0x8086, 0x2445, 0x1458, 0xa002, NULL, NULL, NULL, P3, "GIGABYTE", "GA-8IRML", 0, OK, intel_ich_gpio25_raise}, {0x8086, 0x24c3, 0x1458, 0x24c2, 0x8086, 0x24cd, 0x1458, 0x5004, NULL, NULL, NULL, P3, "GIGABYTE", "GA-8PE667 Ultra 2", 0, OK, intel_ich_gpio32_raise}, {0x10DE, 0x02F1, 0x1458, 0x5000, 0x10DE, 0x0261, 0x1458, 0x5001, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8N51GMF", 0, OK, nvidia_mcp_gpio3b_raise}, diff --git a/print.c b/print.c index 9f31194..2e34fee 100644 --- a/print.c +++ b/print.c @@ -515,6 +515,7 @@ const struct board_info boards_known[] = { B("GIGABYTE", "GA-7DXR", 1, "http://www.gigabyte.de/Products/Motherboard/Products_Spec.aspx?ProductID=13…", NULL), B("GIGABYTE", "GA-7VT600", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1666", NULL), B("GIGABYTE", "GA-7ZM", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1366", "Works fine if you remove jumper JP9 on the board and disable the flash protection BIOS option."), + B("GIGABYTE", "GA-8IP775", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1830", NULL), B("GIGABYTE", "GA-8IRML", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1343", NULL), B("GIGABYTE", "GA-8PE667 Ultra 2", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1607", NULL), B("GIGABYTE", "GA-965P-DS4", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2288", NULL), -- 1.7.1

1 0

[PATCH 1/2] add (untested) board enable for GA-K8NS Pro-939
by Stefan Tauner 12 Jun '11

12 Jun '11

flashrom -V (before patch): http://paste.flashrom.org/view.php?id=531 lspci (short): http://paste.flashrom.org/view.php?id=532 lspci (verbose): http://paste.flashrom.org/view.php?id=533 Signed-off-by: Idwer Vollering <vidwer(a)gmail.com> Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- board_enable.c | 14 ++++++++++++-- print.c | 1 + 2 files changed, 13 insertions(+), 2 deletions(-) diff --git a/board_enable.c b/board_enable.c index 71e6636..a41f18d 100644 --- a/board_enable.c +++ b/board_enable.c @@ -985,6 +985,15 @@ static int nvidia_mcp_gpio8_raise(void) /* * Suited for: + * - Gigabyte GA-K8NS Pro-939: Socket 939 + NVIDIA nForce3 + CK8 + */ +static int nvidia_mcp_gpio0a_raise(void) +{ + return nvidia_mcp_gpio_set(0x0a, 1); +} + +/* + * Suited for: * - MSI K8N Neo2 Platinum: Socket 939 + nForce3 Ultra + CK8 */ static int nvidia_mcp_gpio0c_raise(void) @@ -2015,12 +2024,13 @@ const struct board_pciid_enable board_pciid_enables[] = { {0x8086, 0x24c3, 0x1458, 0x24c2, 0x8086, 0x24cd, 0x1458, 0x5004, NULL, NULL, NULL, P3, "GIGABYTE", "GA-8PE667 Ultra 2", 0, OK, intel_ich_gpio32_raise}, {0x10DE, 0x02F1, 0x1458, 0x5000, 0x10DE, 0x0261, 0x1458, 0x5001, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8N51GMF", 0, OK, nvidia_mcp_gpio3b_raise}, {0x10DE, 0x026C, 0x1458, 0xA102, 0x10DE, 0x0260, 0x1458, 0x5001, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8N51GMF-9", 0, OK, nvidia_mcp_gpio3b_raise}, + {0x10de, 0x00e4, 0x1458, 0x0c11, 0x10de, 0x00e0, 0x1458, 0x0c11, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8NS Pro-939", 0, NT, nvidia_mcp_gpio0a_raise}, {0x10DE, 0x0050, 0x1458, 0x0C11, 0x10DE, 0x005e, 0x1458, 0x5000, NULL, NULL, NULL, P3, "GIGABYTE", "GA-K8N-SLI", 0, OK, nvidia_mcp_gpio21_raise}, - {0x8086, 0x2415, 0x103c, 0x1250, 0x10b7, 0x9200, 0x103c, 0x1247, NULL, NULL, NULL, P3, "HP", "e-Vectra P2706T", 0, OK, board_hp_p2706t}, + {0x8086, 0x2415, 0x103c, 0x1250, 0x10b7, 0x9200, 0x103c, 0x1247, NULL, NULL, NULL, P3, "HP", "e-Vectra P2706T", 0, OK, board_hp_p2706t}, {0x1166, 0x0223, 0x103c, 0x320d, 0x14e4, 0x1678, 0x103c, 0x703e, NULL, "hp", "dl145_g3", P3, "HP", "ProLiant DL145 G3", 0, OK, board_hp_dl145_g3_enable}, {0x1166, 0x0223, 0x103c, 0x320d, 0x14e4, 0x1648, 0x103c, 0x310f, NULL, "hp", "dl165_g6", P3, "HP", "ProLiant DL165 G6", 0, OK, board_hp_dl165_g6_enable}, {0x8086, 0x2580, 0x103c, 0x2a08, 0x8086, 0x2640, 0x103c, 0x2a0a, NULL, NULL, NULL, P3, "HP", "Puffer2-UL8E", 0, OK, intel_ich_gpio18_raise}, - {0x8086, 0x2415, 0x103c, 0x1249, 0x10b7, 0x9200, 0x103c, 0x1246, NULL, NULL, NULL, P3, "HP", "Vectra VL400", 0, OK, board_hp_vl400}, + {0x8086, 0x2415, 0x103c, 0x1249, 0x10b7, 0x9200, 0x103c, 0x1246, NULL, NULL, NULL, P3, "HP", "Vectra VL400", 0, OK, board_hp_vl400}, {0x8086, 0x1a30, 0x103c, 0x1a30, 0x8086, 0x2443, 0x103c, 0x2440, "^VL420$", NULL, NULL, P3, "HP", "Vectra VL420 SFF", 0, OK, intel_ich_gpio22_raise}, {0x10de, 0x0369, 0x103c, 0x12fe, 0x10de, 0x0364, 0x103c, 0x12fe, NULL, "hp", "xw9400", P3, "HP", "xw9400", 0, OK, nvidia_mcp_gpio5_raise}, {0x8086, 0x27A0, 0, 0, 0x8086, 0x27B9, 0, 0, NULL, "ibase", "mb899", P3, "IBASE", "MB899", 0, OK, intel_ich_gpio26_raise}, diff --git a/print.c b/print.c index cec6810..9f31194 100644 --- a/print.c +++ b/print.c @@ -523,6 +523,7 @@ const struct board_info boards_known[] = { B("GIGABYTE", "GA-K8N-SLI", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1928", NULL), B("GIGABYTE", "GA-K8N51GMF", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1950", NULL), B("GIGABYTE", "GA-K8N51GMF-9", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1939", NULL), + B("GIGABYTE", "GA-K8NS Ultra-939", 0, "http://www.gigabyte.com/products/product-page.aspx?pid=1839", "Untested board enable."), B("GIGABYTE", "GA-M57SLI-S4", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2287", NULL), B("GIGABYTE", "GA-M61P-S3", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2434", NULL), B("GIGABYTE", "GA-MA69VM-S2", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=2500", NULL), -- 1.7.1

1 0

Re: [flashrom] [PATCH 06/12] add missing ICH9 register macros and use them to eliminate magic numbers
by Carl-Daniel Hailfinger 12 Jun '11

12 Jun '11

Am 08.06.2011 04:55 schrieb Stefan Tauner: > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> with two minor changes: > @@ -537,15 +549,15 @@ static int program_opcodes(OPCODES *op, int enable_undo) > */ > void ich_set_bbar(uint32_t minaddr) > { > -#define BBAR_MASK 0x00ffff00 > minaddr &= BBAR_MASK; > switch (spi_programmer->type) { > case SPI_CONTROLLER_ICH7: > case SPI_CONTROLLER_VIA: > ichspi_bbar = mmio_readl(ich_spibar + 0x50) & ~BBAR_MASK; > - if (ichspi_bbar) > + if (ichspi_bbar) { > msg_pdbg("Reserved bits in BBAR not zero: 0x%04x", > ichspi_bbar); > + } > Kill the additional braces, please. I know this is a multiline statement, but it is only a single statement and the indentation of the second line makes it obvious where it belongs to. > @@ -556,13 +568,14 @@ void ich_set_bbar(uint32_t minaddr) > msg_perr("Setting BBAR failed!\n"); > break; > case SPI_CONTROLLER_ICH9: > - ichspi_bbar = mmio_readl(ich_spibar + 0xA0) & ~BBAR_MASK; > - if (ichspi_bbar) > + ichspi_bbar = mmio_readl(ich_spibar + ICH9_REG_BBAR) & ~BBAR_MASK; > + if (ichspi_bbar) { > msg_pdbg("Reserved bits in BBAR not zero: 0x%04x", > ichspi_bbar); > + } > Same here. Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

[commit] r1334 - trunk
by repository service 12 Jun '11

12 Jun '11

Author: stefanct Date: Sun Jun 12 10:14:10 2011 New Revision: 1334 URL: http://flashrom.org/trac/flashrom/changeset/1334 Log: ichspi.c: add missing ICH9 register macros and eliminate magic numbers - add macros for FRAP, FREG0, PR0-PR4 and BBAR - eliminate magic numbers representing those registers and some other bits too - remove printing out the contents of FDOC because it is useless Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/ichspi.c Modified: trunk/ichspi.c ============================================================================== --- trunk/ichspi.c Sat Jun 11 21:44:31 2011 (r1333) +++ trunk/ichspi.c Sun Jun 12 10:14:10 2011 (r1334) @@ -77,6 +77,15 @@ #define ICH9_REG_FADDR 0x08 /* 32 Bits */ #define ICH9_REG_FDATA0 0x10 /* 64 Bytes */ +#define ICH9_REG_FRAP 0x50 /* 32 Bytes Flash Region Access Permissions */ +#define ICH9_REG_FREG0 0x54 /* 32 Bytes Flash Region 0 */ + +#define ICH9_REG_PR0 0x74 /* 32 Bytes Protected Range 0 */ +#define ICH9_REG_PR1 0x78 /* 32 Bytes Protected Range 1 */ +#define ICH9_REG_PR2 0x7c /* 32 Bytes Protected Range 2 */ +#define ICH9_REG_PR3 0x80 /* 32 Bytes Protected Range 3 */ +#define ICH9_REG_PR4 0x84 /* 32 Bytes Protected Range 4 */ + #define ICH9_REG_SSFS 0x90 /* 08 Bits */ #define SSFS_SCIP_OFF 0 /* SPI Cycle In Progress */ #define SSFS_SCIP (0x1 << SSFS_SCIP_OFF) @@ -119,6 +128,9 @@ #define ICH9_REG_OPTYPE 0x96 /* 16 Bits */ #define ICH9_REG_OPMENU 0x98 /* 64 Bits */ +#define ICH9_REG_BBAR 0xA0 /* 32 Bits BIOS Base Address Configuration */ +#define BBAR_MASK 0x00ffff00 /* 8-23: Bottom of System Flash */ + // ICH9R SPI commands #define SPI_OPCODE_TYPE_READ_NO_ADDRESS 0 #define SPI_OPCODE_TYPE_WRITE_NO_ADDRESS 1 @@ -545,7 +557,6 @@ */ void ich_set_bbar(uint32_t minaddr) { -#define BBAR_MASK 0x00ffff00 minaddr &= BBAR_MASK; switch (spi_programmer->type) { case SPI_CONTROLLER_ICH7: @@ -564,13 +575,13 @@ msg_perr("Setting BBAR failed!\n"); break; case SPI_CONTROLLER_ICH9: - ichspi_bbar = mmio_readl(ich_spibar + 0xA0) & ~BBAR_MASK; + ichspi_bbar = mmio_readl(ich_spibar + ICH9_REG_BBAR) & ~BBAR_MASK; if (ichspi_bbar) msg_pdbg("Reserved bits in BBAR not zero: 0x%04x", ichspi_bbar); ichspi_bbar |= minaddr; - rmmio_writel(ichspi_bbar, ich_spibar + 0xA0); - ichspi_bbar = mmio_readl(ich_spibar + 0xA0); + rmmio_writel(ichspi_bbar, ich_spibar + ICH9_REG_BBAR); + ichspi_bbar = mmio_readl(ich_spibar + ICH9_REG_BBAR); /* We don't have any option except complaining. And if the write * failed, the restore will fail as well, so no problem there. */ @@ -1154,7 +1165,7 @@ uint32_t base, limit; int rwperms = (((ICH_BRWA(frap) >> i) & 1) << 1) | (((ICH_BRRA(frap) >> i) & 1) << 0); - int offset = 0x54 + i * 4; + int offset = ICH9_REG_FREG0 + i * 4; uint32_t freg = mmio_readl(ich_spibar + offset); msg_pdbg("0x%02X: 0x%08x (FREG%i: %s)\n", @@ -1264,19 +1275,19 @@ ich_init_opcodes(); break; case SPI_CONTROLLER_ICH9: - tmp2 = mmio_readw(ich_spibar + 4); + tmp2 = mmio_readw(ich_spibar + ICH9_REG_HSFS); msg_pdbg("0x04: 0x%04x (HSFS)\n", tmp2); prettyprint_ich9_reg_hsfs(tmp2); - if (tmp2 & (1 << 15)) { + if (tmp2 & HSFS_FLOCKDN) { msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n"); ichspi_lock = 1; } - tmp2 = mmio_readw(ich_spibar + 6); + tmp2 = mmio_readw(ich_spibar + ICH9_REG_HSFC); msg_pdbg("0x06: 0x%04x (HSFC)\n", tmp2); prettyprint_ich9_reg_hsfc(tmp2); - tmp = mmio_readl(ich_spibar + 0x50); + tmp = mmio_readl(ich_spibar + ICH9_REG_FRAP); msg_pdbg("0x50: 0x%08x (FRAP)\n", tmp); msg_pdbg("BMWAG 0x%02x, ", ICH_BMWAG(tmp)); msg_pdbg("BMRAG 0x%02x, ", ICH_BMRAG(tmp)); @@ -1288,39 +1299,37 @@ do_ich9_spi_frap(tmp, i); msg_pdbg("0x74: 0x%08x (PR0)\n", - mmio_readl(ich_spibar + 0x74)); + mmio_readl(ich_spibar + ICH9_REG_PR0)); msg_pdbg("0x78: 0x%08x (PR1)\n", - mmio_readl(ich_spibar + 0x78)); + mmio_readl(ich_spibar + ICH9_REG_PR1)); msg_pdbg("0x7C: 0x%08x (PR2)\n", - mmio_readl(ich_spibar + 0x7C)); + mmio_readl(ich_spibar + ICH9_REG_PR2)); msg_pdbg("0x80: 0x%08x (PR3)\n", - mmio_readl(ich_spibar + 0x80)); + mmio_readl(ich_spibar + ICH9_REG_PR3)); msg_pdbg("0x84: 0x%08x (PR4)\n", - mmio_readl(ich_spibar + 0x84)); + mmio_readl(ich_spibar + ICH9_REG_PR4)); - tmp = mmio_readl(ich_spibar + 0x90); + tmp = mmio_readl(ich_spibar + ICH9_REG_SSFS); msg_pdbg("0x90: 0x%02x (SSFS)\n", tmp & 0xff); prettyprint_ich9_reg_ssfs(tmp); - if (tmp & (1 << 3)) { + if (tmp & SSFS_FCERR) { msg_pdbg("Clearing SSFS.FCERR\n"); - mmio_writeb(1 << 3, ich_spibar + 0x90); + mmio_writeb(SSFS_FCERR, ich_spibar + ICH9_REG_SSFS); } msg_pdbg("0x91: 0x%06x (SSFC)\n", tmp >> 8); prettyprint_ich9_reg_ssfc(tmp); msg_pdbg("0x94: 0x%04x (PREOP)\n", - mmio_readw(ich_spibar + 0x94)); + mmio_readw(ich_spibar + ICH9_REG_PREOP)); msg_pdbg("0x96: 0x%04x (OPTYPE)\n", - mmio_readw(ich_spibar + 0x96)); + mmio_readw(ich_spibar + ICH9_REG_OPTYPE)); msg_pdbg("0x98: 0x%08x (OPMENU)\n", - mmio_readl(ich_spibar + 0x98)); + mmio_readl(ich_spibar + ICH9_REG_OPMENU)); msg_pdbg("0x9C: 0x%08x (OPMENU+4)\n", - mmio_readl(ich_spibar + 0x9C)); - ichspi_bbar = mmio_readl(ich_spibar + 0xA0); + mmio_readl(ich_spibar + ICH9_REG_OPMENU + 4)); + ichspi_bbar = mmio_readl(ich_spibar + ICH9_REG_BBAR); msg_pdbg("0xA0: 0x%08x (BBAR)\n", ichspi_bbar); - msg_pdbg("0xB0: 0x%08x (FDOC)\n", - mmio_readl(ich_spibar + 0xB0)); ich_init_opcodes(); break; default:

1 0

← Newer
1
...
21
22
23
24
25
26
27
...
30
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom June 2011