flashrom November 2010

flashrom@flashrom.org

58 participants
146 discussions

[PATCH] W83697xx superio flash enable
by David Borg 05 May '12

05 May '12

Adds a function to enable the flash interface on w83697xx superio's. Still needs to be hooked up to the superio detection framework though. Signed-off-by: David Borg <borg.db(a)gmail.com>

2 1

ASUS OPLX-M results (no flash device found)
by Ville Skyttä 17 Feb '12

17 Feb '12

Hello, I tried out flashrom on a ASUS OPLX-M motherboard, and it didn't find a flash device. I found some info by googling (that I cannot verify) that the OPLX-M would be an OEM (or something) version of the ASUS MEL-M; I suppose this particular board originally came with a Fujitsu/Siemens PC. http://support.asus.com/download/download.aspx?modelname=MEL-M&SLanguage=en…

3 4

Re: [flashrom] Trial of ARIMA:HDAMA Motherboard
by Carl-Daniel Hailfinger 09 Feb '12

09 Feb '12

Hi Mike, On 23.02.2010 05:45, Spangler, Mike T wrote: > I can probe with a continuity tester, but would need to know specific > pin locations to try. Do you have any generic info on doing this? Yes (well, I'd have to write up something), but the solution mentioned by Michael is way easier, so I'll wait until Michael has diagnosed the GPIO settings from the flashrom run on factory BIOS. Regards, Carl-Daniel -- "I do consider assignment statements and pointer variables to be among computer science's most valuable treasures." -- Donald E. Knuth

2 1

[PATCH] dummy programmer: blacklist SPI commands
by Carl-Daniel Hailfinger 08 Feb '12

08 Feb '12

Add optional SPI command blacklisting to the flash chip emulator in the dummy programmer. Usage: flashrom -p dummy:spi_blacklist=hexstring If hexstring is 0302, flashrom will blacklist command 0x03 (READ) and command 0x02 (WRITE). The hexstring can have up to 521 bytes (256 commands) length, and must not start with 0x. TODO: Should 0x at the beginning of hexstring be tolerated? Very useful for testing corner cases if you don't own a locked down Intel chipset and want to simulate such a thing. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-emulate_spi_flashchip_command_blacklist/dummyflasher.c =================================================================== --- flashrom-emulate_spi_flashchip_command_blacklist/dummyflasher.c (Revision 1224) +++ flashrom-emulate_spi_flashchip_command_blacklist/dummyflasher.c (Arbeitskopie) @@ -19,6 +19,7 @@ #include <string.h> #include <stdlib.h> +#include <stdio.h> #include <ctype.h> #include "flash.h" #include "chipdrivers.h" @@ -56,6 +57,8 @@ static int emu_jedec_be_d8_size = 0; static int emu_jedec_ce_60_size = 0; static int emu_jedec_ce_c7_size = 0; +unsigned char spi_blacklist[256]; +int spi_blacklist_size = 0; #endif #endif @@ -71,6 +74,7 @@ { char *bustext = NULL; char *tmp = NULL; + int i; #if EMULATE_CHIP struct stat image_stat; #endif @@ -116,6 +120,31 @@ } } + tmp = extract_programmer_param("spi_blacklist"); + if (tmp) { + i = strlen(tmp); + if (i % 2) { + msg_perr("Invalid SPI command blacklist\n"); + free(tmp); + return 1; + } + tolower_string(tmp); + if (strspn(tmp, "0123456789abcdef") != i) { + msg_perr("Invalid SPI command blacklist\n"); + free(tmp); + return 1; + } + spi_blacklist_size = i / 2; + for (i = 0; i < spi_blacklist_size; i++) { + sscanf(tmp, "%2hhx", &spi_blacklist[i]); + } + msg_pdbg("SPI blacklist is "); + for (i = 0; i < spi_blacklist_size; i++) + msg_pdbg("%02x ", spi_blacklist[i]); + msg_pdbg(", size %i\n", spi_blacklist_size); + } + free(tmp); + #if EMULATE_CHIP tmp = extract_programmer_param("emulate"); if (!tmp) { @@ -285,7 +314,7 @@ static int emulate_spi_chip_response(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr) { - int offs; + int offs, i; static int aai_offs; static int aai_active = 0; @@ -293,7 +322,16 @@ msg_perr("No command sent to the chip!\n"); return 1; } - /* TODO: Implement command blacklists here. */ + for (i = 0; i < spi_blacklist_size; i++) { + if (writearr[0] == spi_blacklist[i]) { + msg_perr("Refusing blacklisted SPI command 0x%02x\n", + spi_blacklist[i]); + /* FIXME: Do we want a separate return code for + * command unavailable? + */ + return 1; + } + } switch (writearr[0]) { case JEDEC_RES: if (emu_chip != EMULATE_ST_M25P10_RES) -- http://www.hailfinger.org/

3 7

AMD SB7xx/SB8xx w/IMC: enable specs
by Joshua Roys 03 Jan '12

03 Jan '12

Hello all, The specific board this is for is the Supermicro H8DGT. Attached is only the specification, which is not guaranteed to be correct. Use with care. Also, after using this, you may want to turn off and unplug the computer for a few minutes to restore the correct operational state. The AMD SB700/710/750 Register Reference Guide (#43009) was used as a reference. Thanks, Josh

2 2

[PATCH] Implement unknown Dediprog commands
by Carl-Daniel Hailfinger 20 Dec '11

20 Dec '11

Secret knowledge is cool, but public knowledge is better. Implement all Dediprog commands found in USB traces, even if their purpose is not yet known. Annotate unknown commands with info about the call sequence they are embedded in and the firmware version of the log. Add a new shutdown command for firmware 5.x. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-dediprog_unknown_commands/dediprog.c =================================================================== --- flashrom-dediprog_unknown_commands/dediprog.c (Revision 1232) +++ flashrom-dediprog_unknown_commands/dediprog.c (Arbeitskopie) @@ -27,6 +27,7 @@ #define DEFAULT_TIMEOUT 3000 static usb_dev_handle *dediprog_handle; +static int dediprog_firmwareversion; #if 0 /* Might be useful for other pieces of code as well. */ @@ -228,6 +229,7 @@ fw[1], fw[2]); return 1; } + dediprog_firmwareversion = fw[0]; return 0; } @@ -253,6 +255,32 @@ return 0; } +#if 0 +/* Something. + * Present in eng_detect_blink.log with firmware 3.1.8 + * Always preceded by Command Receive Device String + */ +static int dediprog_command_b(void) +{ + int ret; + char buf[0x3]; + + memset(buf, 0, sizeof(buf)); + ret = usb_control_msg(dediprog_handle, 0xc3, 0x7, 0x0, 0xef00, buf, 0x3, DEFAULT_TIMEOUT); + if (ret < 0) { + msg_perr("Command B failed (%s)!\n", usb_strerror()); + return 1; + } + if ((ret != 0x3) || (buf[0] != 0xff) || (buf[1] != 0xff) || + (buf[2] != 0xff)) { + msg_perr("Unexpected response to Command B!\n"); + return 1; + } + + return 0; +} +#endif + /* Command C is only sent after dediprog_check_devicestring, but not after every * invocation of dediprog_check_devicestring. It is only sent after the first * dediprog_command_a(); dediprog_check_devicestring() sequence in each session. @@ -264,7 +292,7 @@ ret = usb_control_msg(dediprog_handle, 0x42, 0x4, 0x0, 0x0, NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { - msg_perr("Unexpected response to Command C!\n"); + msg_perr("Command C failed (%s)!\n", usb_strerror()); return 1; } return 0; @@ -274,6 +302,7 @@ /* Very strange. Seems to be a programmer keepalive or somesuch. * Wait unsuccessfully for timeout ms to read one byte. * Is usually called after setting voltage to 0. + * Present in all logs with Firmware 2.1.1 and 3.1.8 */ static int dediprog_command_f(int timeout) { @@ -282,14 +311,90 @@ memset(buf, 0, sizeof(buf)); ret = usb_control_msg(dediprog_handle, 0xc2, 0x11, 0xff, 0xff, buf, 0x1, timeout); + /* This check is most probably wrong. Command F always causes a timeout + * in the logs, so we should check for timeout instead of checking for + * success. + */ + if (ret != 0x1) { + msg_perr("Command F failed (%s)!\n", usb_strerror()); + return 1; + } + return 0; +} + +/* Start/stop blinking? + * Present in eng_detect_blink.log with firmware 3.1.8 + * Preceded by Command J + */ +static int dediprog_command_g(void) +{ + int ret; + + ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x03, NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { - msg_perr("Unexpected response to Command F!\n"); + msg_perr("Command G failed (%s)!\n", usb_strerror()); return 1; } return 0; } + +/* Something. + * Present in all logs with firmware 5.1.5 + * Always preceded by Command Receive Device String + * Always followed by Command Set SPI Voltage nonzero + */ +static int dediprog_command_h(void) +{ + int ret; + + ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x05, NULL, 0x0, DEFAULT_TIMEOUT); + if (ret != 0x0) { + msg_perr("Command H failed (%s)!\n", usb_strerror()); + return 1; + } + return 0; +} #endif +/* Shutdown for firmware 5.x? + * Present in all logs with firmware 5.1.5 + * Often preceded by a SPI operation (Command Read SPI Bulk or Receive SPI) + * Always followed by Command Set SPI Voltage 0x0000 + */ +static int dediprog_command_i(void) +{ + int ret; + + ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x06, NULL, 0x0, DEFAULT_TIMEOUT); + if (ret != 0x0) { + msg_perr("Command I failed (%s)!\n", usb_strerror()); + return 1; + } + return 0; +} + +#if 0 +/* Start/stop blinking? + * Present in all logs with firmware 5.1.5 + * Always preceded by Command Receive Device String on 5.1.5 + * Always followed by Command Set SPI Voltage nonzero on 5.1.5 + * Present in eng_detect_blink.log with firmware 3.1.8 + * Preceded by Command B in eng_detect_blink.log + * Followed by Command G in eng_detect_blink.log + */ +static int dediprog_command_j(void) +{ + int ret; + + ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x07, NULL, 0x0, DEFAULT_TIMEOUT); + if (ret != 0x0) { + msg_perr("Command J failed (%s)!\n", usb_strerror()); + return 1; + } + return 0; +} +#endif + static int parse_voltage(char *voltage) { char *tmp = NULL; @@ -445,9 +550,11 @@ /* URB 136 is just URB 9. */ /* URB 137 is just URB 11. */ - /* Command I is probably Start Bulk Read. Data is u16 blockcount, u16 blocksize. */ - /* Command J is probably Start Bulk Write. Data is u16 blockcount, u16 blocksize. */ - /* Bulk transfer sizes for Command I/J are always 512 bytes, rest is filled with 0xff. */ + /* Command Start Bulk Read. Data is u16 blockcount, u16 blocksize. */ + /* Command Start Bulk Write. Data is u16 blockcount, u16 blocksize. */ + /* Bulk transfer sizes for Command Start Bulk Read/Write are always + * 512 bytes, rest is filled with 0xff. + */ return 0; } @@ -457,6 +564,10 @@ { msg_pspew("%s\n", __func__); + /* Shutdown on firmware 5.x */ + if (dediprog_firmwareversion == 5) + if (dediprog_command_i()) + return 1; /* URB 28. Command Set SPI Voltage to 0. */ if (dediprog_set_spi_voltage(0x0)) return 1; -- http://www.hailfinger.org/

2 2

[PATCH] Fintek SPI driver, based off it87spi
by Sean Nelson 23 Oct '11

23 Oct '11

I've been extremely busy with preparing for the US Air Force, which I leave for Basic on November 2nd. But... Fintek SPI Flashrom Driver: * based off of it87spi.c * untested * should be good for F71882 and F71889 Signed-off-by: Sean Nelson <audiohacked(a)gmail.com>

2 3

patch to add support for Xilinx parallel III/DLC5 programmer cable
by Jakab Peter 12 Sep '11

12 Sep '11

Hi list, I modified the rayer spi programmer source to be used with a Xilinx parallel III (also called DLC5) programmer cable. It's a trivial change of parallel port pins, but I did not know how the support for this cable should be included into the source code. Copying the same code to a separate file may not be a good idea. --- flashrom/rayer_spi.c 2010-09-18 19:48:27.000000000 +0200 +++ ../flashrom/rayer_spi.c 2010-09-18 02:12:59.000000000 +0200 @@ -37,11 +37,11 @@ * independent and are bitshift values, not real pin numbers. */ /* Pins for master->slave direction */ -#define SPI_CS_PIN 5 -#define SPI_SCK_PIN 6 -#define SPI_MOSI_PIN 7 +#define SPI_CS_PIN 2 +#define SPI_SCK_PIN 1 +#define SPI_MOSI_PIN 0 /* Pins for slave->master direction */ -#define SPI_MISO_PIN 6 +#define SPI_MISO_PIN 4 static int lpt_iobase; Thank you for working on this software, with access to the source code I was able to program my w25q64 flash chip. -- Peter JAKAB http://jap.hu/

3 3

Re: [flashrom] [PATCH] Board enable for ASUS P5LP-LE
by Uwe Hermann 25 Aug '11

25 Aug '11

On Wed, Aug 18, 2010 at 06:27:15PM +0200, Michael Karcher wrote: > + * - ASUS P5LP-LE (Epson/HP OEM) OK, this one is going to be interesting. The board is made by ASUS for HP, it seems. HP calls it "Leonite" or "Leonite-GL8E". http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c008… But that would have been too easy. There are a bunch of other boards on the HP site which are also called P5LP-LE, but have different HP code names. From a quick glance I see at least: P5LP-LE (Leonite) P5LP-LE (Leonite2) P5LP-LE (Lithium) P5LP-LE (Limestone) P5LP-LE (Emery) Fun! I don't know how to differ between them, the dmidecode from Leon Zhang <leoncamel(a)gmail.com> said: DMI string system-manufacturer: "EPSON DIRECT CORP." DMI string system-product-name: "Endeavor MT7700" DMI string system-version: "" DMI string baseboard-manufacturer: "ASUSTek Computer INC." DMI string baseboard-product-name: "P5LP-LE" We don't know if other "P5LP-LE" might have the "Leonite" (or other) HP code name in there or not. Maybe something is printed as silkscreen on the board? An then one of these HP OEM boards is built into the Epson "Endeavor MT7700" system/PC. So it's a bit unclear which vendor/board name we should use in this case. It's probably best to mention all of them for better googling results. Attached is a slightly updated patch for review, let me know what you think. Uwe. -- http://hermann-uwe.de | http://sigrok.org http://randomprojects.org | http://unmaintained-free-software.org

3 2

[PATCH] internal dmi decoder
by Sean Nelson 16 Aug '11

16 Aug '11

Here is a new version of the internal dmi decoding. To use the new decoder, the user needs to use "-p internal:dmi=new", to cross-check with the external dmidecode use "-p internal:dmi=check". Hopefully if this is comitted, it will make it easier for people to test the new internal decoder. Signed-off-by: Sean Nelson <audiohacked(a)gmail.com>

5 8

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom November 2010