Signed-off-by: Luc Verhaegen libv@skynet.be --- board_enable.c | 371 ++++++++++++++++++++++++++++++++++---------------------- 1 files changed, 225 insertions(+), 146 deletions(-)
diff --git a/board_enable.c b/board_enable.c index 21b91f1..35f43ba 100644 --- a/board_enable.c +++ b/board_enable.c @@ -523,32 +523,6 @@ static int board_epox_ep_bx3(const char *name) }
/** - * Suited for Acorp 6A815EPD. - */ -static int board_acorp_6a815epd(const char *name) -{ - struct pci_dev *dev; - uint16_t port; - uint8_t val; - - dev = pci_dev_find(0x8086, 0x2440); /* Intel ICH2 LPC */ - if (!dev) { - fprintf(stderr, "\nERROR: ICH2 LPC bridge not found.\n"); - return -1; - } - - /* Use GPIOBASE register to find where the GPIO is mapped. */ - port = (pci_read_word(dev, 0x58) & 0xFFC0) + 0xE; - - val = INB(port); - val |= 0x80; /* Top Block Lock -- pin 8 of PLCC32 */ - val |= 0x40; /* Lower Blocks Lock -- pin 7 of PLCC32 */ - OUTB(val, port); - - return 0; -} - -/** * Suited for Artec Group DBE61 and DBE62. */ static int board_artecgroup_dbe6x(const char *name) @@ -590,105 +564,262 @@ static int board_artecgroup_dbe6x(const char *name) }
/** - * Set the specified GPIO on the specified ICHx southbridge to high. - * - * @param name The name of this board. - * @param ich_vendor PCI vendor ID of the specified ICHx southbridge. - * @param ich_device PCI device ID of the specified ICHx southbridge. - * @param gpiobase_reg GPIOBASE register offset in the LPC bridge. - * @param gp_lvl Offset of GP_LVL register in I/O space, relative to GPIOBASE. - * @param gp_lvl_bitmask GP_LVL bitmask (set GPIO bits to 1, all others to 0). - * @param gpio_bit The bit (GPIO) which shall be set to high. - * @return If the write-enable was successful return 0, otherwise return -1. + * Set a GPIO line on a given intel ICH LPC controller. */ -static int ich_gpio_raise(const char *name, uint16_t ich_vendor, - uint16_t ich_device, uint8_t gpiobase_reg, - uint8_t gp_lvl, uint32_t gp_lvl_bitmask, - unsigned int gpio_bit) +static int intel_ich_gpio_set(int gpio, int raise) { + /* table mapping the different intel ICH LPC chipsets. */ + static struct { + uint16_t id; + uint8_t base_reg; + uint32_t bank0; + uint32_t bank1; + uint32_t bank2; + } intel_ich_gpio_table[] = { + {0x2410, 0x58, 0x0FE30000, 0, 0}, /* 82801AA (ICH) */ + {0x2420, 0x58, 0x0FE30000, 0, 0}, /* 82801AB (ICH0) */ + {0x2440, 0x58, 0x1BFF391B, 0, 0}, /* 82801BA (ICH2) */ + {0x244C, 0x58, 0x1A23399B, 0, 0}, /* 82801BAM (ICH2M) */ + {0x2450, 0x58, 0x1BFF0000, 0, 0}, /* 82801E (C-ICH) */ + {0x2480, 0x58, 0x1BFF0000, 0x00000FFF, 0}, /* 82801CA (ICH3-S) */ + {0x248C, 0x58, 0x1A230000, 0x00000FFF, 0}, /* 82801CAM (ICH3-M) */ + {0x24C0, 0x58, 0x1BFF0000, 0x00000FFF, 0}, /* 82801DB/DBL (ICH4/ICH4-L) */ + {0x24CC, 0x58, 0x1A030000, 0x00000FFF, 0}, /* 82801DBM (ICH4-M) */ + {0x24D0, 0x58, 0x1BFF0000, 0x00030305, 0}, /* 82801EB/ER (ICH5/ICH5R) */ + {0x2640, 0x48, 0x1BFF0000, 0x00030307, 0}, /* 82801FB/FR (ICH6/ICH6R) */ + {0x2641, 0x48, 0x1BFF0000, 0x00030307, 0}, /* 82801FBM (ICH6M) */ + {0x27B8, 0x48, 0xFFFFFFFF, 0x000300FF, 0}, /* 82801GB/GR (ICH7 Family) */ + {0x27B9, 0x48, 0xFFEBFFFE, 0x000300FE, 0}, /* 82801GBM (ICH7-M) */ + {0x27BD, 0x48, 0xFFEBFFFE, 0x000300FE, 0}, /* 82801GHM (ICH7-M DH) */ + {0x2810, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HB/HR (ICH8/R) */ + {0x2811, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HBM (ICH8M-E) */ + {0x2812, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HH (ICH8DH) */ + {0x2814, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HO (ICH8DO) */ + {0x2815, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HEM (ICH8M) */ + {0x2912, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IH (ICH9DH) */ + {0x2914, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IO (ICH9DO) */ + {0x2916, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IR (ICH9R) */ + {0x2917, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IEM (ICH9M-E) */ + {0x2918, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IB (ICH9) */ + {0x2919, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IBM (ICH9M) */ + {0x3A14, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JDO (ICH10DO) */ + {0x3A16, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIR (ICH10R) */ + {0x3A18, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIB (ICH10) */ + {0x3A1A, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JD (ICH10D) */ + {0, 0, 0, 0, 0} /* end marker */ + }; + struct pci_dev *dev; - uint16_t gpiobar; - uint32_t reg32; + uint16_t base; + uint32_t tmp; + int i, allowed; + + /* First, look for a known LPC bridge */ + for (dev = pacc->devices; dev; dev = dev->next) + if ((dev->vendor_id == 0x8086) && + (dev->device_class == 0x0601)) { /* ISA Bridge */ + /* Is this device in our list? */ + for (i = 0; intel_ich_gpio_table[i].id; i++) + if (dev->device_id == intel_ich_gpio_table[i].id) + break; + + if (intel_ich_gpio_table[i].id) + break; + }
- dev = pci_dev_find(ich_vendor, ich_device); /* Intel ICHx LPC */ if (!dev) { - fprintf(stderr, "\nERROR: ICHx LPC dev %4x:%4x not found.\n", - ich_vendor, ich_device); + fprintf(stderr, "\nERROR: No Known Intel LPC Bridge found.\n"); return -1; }
- /* Use GPIOBASE register to find the I/O space for GPIO. */ - gpiobar = pci_read_word(dev, gpiobase_reg) & gp_lvl_bitmask; + /* According to the datasheets, all intel ICHs have the gpio bar 5:1 + strapped to zero. From some mobile ich9 version on, this becomes + 6:1. The mask below catches all. */ + base = pci_read_word(dev, intel_ich_gpio_table[i].base_reg) & 0xFFC0;
- /* Set specified GPIO to high. */ - reg32 = INL(gpiobar + gp_lvl); - reg32 |= (1 << gpio_bit); - OUTL(reg32, gpiobar + gp_lvl); + /* check whether the line is allowed */ + if (gpio < 32) + allowed = (intel_ich_gpio_table[i].bank0 >> gpio) & 0x01; + else if (gpio < 64) + allowed = (intel_ich_gpio_table[i].bank1 >> (gpio - 32)) & 0x01; + else + allowed = (intel_ich_gpio_table[i].bank2 >> (gpio - 64)) & 0x01; + + if (!allowed) { + fprintf(stderr, "\nERROR: This Intel LPC Bridge does not allow" + " setting GPIO%02d\n", gpio); + return -1; + } + + printf("\nIntel ICH LPC Bridge: %sing GPIO%02d.\n", + raise ? "Rais" : "Dropp", gpio); + + if (gpio < 32) { + /* Set line to GPIO */ + tmp = INL(base); + /* ICH/ICH0 multiplexes 27/28 on the line set. */ + if ((gpio == 28) && + ((dev->device_id == 0x2410) || (dev->device_id == 0x2420))) + tmp |= 1 << 27; + else + tmp |= 1 << gpio; + OUTL(tmp, base); + + /* As soon as we are talking to ICH8 and above, this register + decides whether we can set the gpio or not. */ + if (dev->device_id > 0x2800) { + tmp = INL(base); + if (!(tmp & (1 << gpio))) { + fprintf(stderr, "\nERROR: This Intel LPC Bridge" + " does not allow setting GPIO%02d\n", + gpio); + return -1; + } + } + + /* Set GPIO to OUTPUT */ + tmp = INL(base + 0x04); + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x04); + + /* Raise GPIO line */ + tmp = INL(base + 0x0C); + if (raise) + tmp |= 1 << gpio; + else + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x0C); + } else if (gpio < 64) { + gpio -= 32; + + /* Set line to GPIO */ + tmp = INL(base + 0x30); + tmp |= 1 << gpio; + OUTL(tmp, base + 0x30); + + /* As soon as we are talking to ICH8 and above, this register + decides whether we can set the gpio or not. */ + if (dev->device_id > 0x2800) { + tmp = INL(base + 30); + if (!(tmp & (1 << gpio))) { + fprintf(stderr, "\nERROR: This Intel LPC Bridge" + " does not allow setting GPIO%02d\n", + gpio + 32); + return -1; + } + } + + /* Set GPIO to OUTPUT */ + tmp = INL(base + 0x34); + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x34); + + /* Raise GPIO line */ + tmp = INL(base + 0x38); + if (raise) + tmp |= 1 << gpio; + else + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x38); + } else { + gpio -= 64; + + /* Set line to GPIO */ + tmp = INL(base + 0x40); + tmp |= 1 << gpio; + OUTL(tmp, base + 0x40); + + tmp = INL(base + 40); + if (!(tmp & (1 << gpio))) { + fprintf(stderr, "\nERROR: This Intel LPC Bridge does " + "not allow setting GPIO%02d\n", gpio + 64); + return -1; + } + + /* Set GPIO to OUTPUT */ + tmp = INL(base + 0x44); + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x44); + + /* Raise GPIO line */ + tmp = INL(base + 0x48); + if (raise) + tmp |= 1 << gpio; + else + tmp &= ~(1 << gpio); + OUTL(tmp, base + 0x48); + }
return 0; }
/** - * Suited for ASUS P4B266. + * Suited for Abit IP35: Intel P35 + ICH9R. */ -static int ich2_gpio22_raise(const char *name) +static int intel_ich_gpio16_raise(const char *name) { - return ich_gpio_raise(name, 0x8086, 0x2440, 0x58, 0x0c, 0xffc0, 22); + return intel_ich_gpio_set(16, 1); }
/** - * Suited for the Dell PowerEdge 1850. All parameters except the last one are - * documented in the public Intel 82801EB ICH5 / 82801ER ICH5R datasheet. The - * last parameter (GPIO number) has to be in the range [16,31] according to - * said Intel datasheet and was found by exhaustive search. + * Suited for MSI MS-7046: LGA775 + 915P + ICH6. */ -static int ich5_gpio23_raise(const char *name) +static int intel_ich_gpio19_raise(const char *name) { - return ich_gpio_raise(name, 0x8086, 0x24d0, 0x58, 0x0c, 0xffc0, 23); + return intel_ich_gpio_set(19, 1); }
/** - * Suited for MSI MS-7046. + * Suited for Asus P4P800-E Deluxe: Intel socket478 + 865PE + ICH5R. */ -static int ich6_gpio19_raise(const char *name) +static int intel_ich_gpio21_raise(const char *name) { - return ich_gpio_raise(name, 0x8086, 0x2640, 0x48, 0x0c, 0xffc0, 19); + return intel_ich_gpio_set(21, 1); }
-static int board_kontron_986lcd_m(const char *name) +/** + * Suited for ASUS P4B266: socket478 + intel 845D + ICH2. + */ +static int intel_ich_gpio22_raise(const char *name) { - struct pci_dev *dev; - uint16_t gpiobar; - uint32_t val; + return intel_ich_gpio_set(22, 1); +}
-#define ICH7_GPIO_LVL2 0x38 +/** + * Suited for Dell Poweredge 1850: Intel PPGA604 + E7520 + ICH5R. + */ +static int intel_ich_gpio23_raise(const char *name) +{ + return intel_ich_gpio_set(23, 1); +}
- dev = pci_dev_find(0x8086, 0x27b8); /* Intel ICH7 LPC */ - if (!dev) { - // This will never happen on this board - fprintf(stderr, "\nERROR: ICH7 LPC bridge not found.\n"); - return -1; - } +/** + * Suited for Acorp 6A815EPD: socket 370 + intel 815 + ICH2. + */ +static int board_acorp_6a815epd(const char *name) +{ + int ret;
- /* Use GPIOBASE register to find where the GPIO is mapped. */ - gpiobar = pci_read_word(dev, 0x48) & 0xfffc; + /* Lower Blocks Lock -- pin 7 of PLCC32 */ + ret = intel_ich_gpio_set(22, 1); + if (!ret) /* Top Block Lock -- pin 8 of PLCC32 */ + ret = intel_ich_gpio_set(23, 1);
- val = INL(gpiobar + ICH7_GPIO_LVL2); /* GP_LVL2 */ - printf_debug("\nGPIOBAR=0x%04x GP_LVL: 0x%08x\n", gpiobar, val); + return ret; +}
- /* bit 2 (0x04) = 0 #TBL --> bootblock locking = 1 - * bit 2 (0x04) = 1 #TBL --> bootblock locking = 0 - * bit 3 (0x08) = 0 #WP --> block locking = 1 - * bit 3 (0x08) = 1 #WP --> block locking = 0 - * - * To enable full block locking, you would do: - * val &= ~ ((1 << 2) | (1 << 3)); - */ - val |= (1 << 2) | (1 << 3); +/** + * Suited for Kontron 986LCD-M: socket478 + 915GM + ICH7R. + */ +static int board_kontron_986lcd_m(const char *name) +{ + int ret;
- OUTL(val, gpiobar + ICH7_GPIO_LVL2); + ret = intel_ich_gpio_set(34, 1); /* #TBL */ + if (!ret) + ret = intel_ich_gpio_set(35, 1); /* #WP */
- return 0; + return ret; }
/** @@ -881,32 +1012,6 @@ static int board_mitac_6513wu(const char *name) }
/** - * Suited for Abit IP35: Intel P35 + ICH9R. - */ -static int board_abit_ip35(const char *name) -{ - struct pci_dev *dev; - uint16_t base; - uint8_t tmp; - - dev = pci_dev_find(0x8086, 0x2916); /* Intel ICH9R LPC Interface */ - if (!dev) { - fprintf(stderr, "\nERROR: Intel ICH9R LPC not found.\n"); - return -1; - } - - /* get LPC GPIO base */ - base = pci_read_long(dev, 0x48) & 0x0000FFC0; - - /* Raise GPIO 16 */ - tmp = INB(base + 0x0E); - tmp |= 0x01; - OUTB(tmp, base + 0x0E); - - return 0; -} - -/** * Suited for Asus A7V8X: VIA KT400 + VT8235 + IT8703F-A */ static int board_asus_a7v8x(const char *name) @@ -1009,32 +1114,6 @@ static int board_asus_a7v600x(const char *name) }
/** - * Suited for Asus P4P800-E Deluxe: Intel Intel 865PE + ICH5R. - */ -static int board_asus_p4p800(const char *name) -{ - struct pci_dev *dev; - uint16_t base; - uint8_t tmp; - - dev = pci_dev_find(0x8086, 0x24D0); /* Intel ICH5R ISA Bridge */ - if (!dev) { - fprintf(stderr, "\nERROR: Intel ICH5R ISA Bridge not found.\n"); - return -1; - } - - /* get PM IO base */ - base = pci_read_long(dev, 0x58) & 0x0000FFC0; - - /* Raise GPIO 21 */ - tmp = INB(base + 0x0E); - tmp |= 0x20; - OUTB(tmp, base + 0x0E); - - return 0; -} - -/** * Below is the list of boards which need a special "board enable" code in * flashrom before their ROM chip can be accessed/written to. * @@ -1063,7 +1142,7 @@ static int board_asus_p4p800(const char *name) /* Please keep this list alphabetically ordered by vendor/board name. */ struct board_pciid_enable board_pciid_enables[] = { /* first pci-id set [4], second pci-id set [4], coreboot id [2], vendor name board name flash enable */ - {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, "Abit", "IP35", board_abit_ip35}, + {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, "Abit", "IP35", intel_ich_gpio16_raise}, {0x8086, 0x1130, 0, 0, 0x105a, 0x0d30, 0x105a, 0x4d33, "acorp", "6a815epd", "Acorp", "6A815EPD", board_acorp_6a815epd}, {0x1022, 0x746B, 0x1022, 0x36C0, 0, 0, 0, 0, "AGAMI", "ARUMA", "agami", "Aruma", w83627hf_gpio24_raise_2e}, {0x1106, 0x3177, 0x17F2, 0x3177, 0x1106, 0x3148, 0x17F2, 0x3148, NULL, NULL, "Albatron", "PM266A*", board_epox_ep_8k5a2}, @@ -1073,12 +1152,12 @@ struct board_pciid_enable board_pciid_enables[] = { {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3065, 0x1043, 0x80ED, NULL, NULL, "ASUS", "A7V600-X", board_asus_a7v600x}, {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x808C, NULL, NULL, "ASUS", "A7V8X", board_asus_a7v8x}, {0x1106, 0x3177, 0x1043, 0x80A1, 0x1106, 0x3205, 0x1043, 0x8118, NULL, NULL, "ASUS", "A7V8X-MX SE", board_asus_a7v8x_mx}, - {0x8086, 0x1a30, 0x1043, 0x8070, 0x8086, 0x244b, 0x1043, 0x8028, NULL, NULL, "ASUS", "P4B266", ich2_gpio22_raise}, - {0x8086, 0x2570, 0x1043, 0x80F2, 0x105A, 0x3373, 0x1043, 0x80F5, NULL, NULL, "ASUS", "P4P800-E Deluxe", board_asus_p4p800}, + {0x8086, 0x1a30, 0x1043, 0x8070, 0x8086, 0x244b, 0x1043, 0x8028, NULL, NULL, "ASUS", "P4B266", intel_ich_gpio22_raise}, + {0x8086, 0x2570, 0x1043, 0x80F2, 0x105A, 0x3373, 0x1043, 0x80F5, NULL, NULL, "ASUS", "P4P800-E Deluxe", intel_ich_gpio21_raise}, {0x10B9, 0x1541, 0, 0, 0x10B9, 0x1533, 0, 0, "asus", "p5a", "ASUS", "P5A", board_asus_p5a}, {0x10DE, 0x0030, 0x1043, 0x818a, 0x8086, 0x100E, 0x1043, 0x80EE, NULL, NULL, "ASUS", "P5ND2-SLI Deluxe", board_asus_p5nd2_sli}, {0x1106, 0x3149, 0x1565, 0x3206, 0x1106, 0x3344, 0x1565, 0x1202, NULL, NULL, "Biostar", "P4M80-M4", it8705_rom_write_enable}, - {0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, "Dell", "PowerEdge 1850", ich5_gpio23_raise}, + {0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, "Dell", "PowerEdge 1850", intel_ich_gpio23_raise}, {0x1106, 0x3038, 0x1019, 0x0996, 0x1106, 0x3177, 0x1019, 0x0996, NULL, NULL, "Elitegroup", "K7VTA3", it8705f_write_enable_2e}, {0x1106, 0x3177, 0x1106, 0x3177, 0x1106, 0x3059, 0x1695, 0x3005, NULL, NULL, "EPoX", "EP-8K5A2", board_epox_ep_8k5a2}, {0x10EC, 0x8139, 0x1695, 0x9001, 0x11C1, 0x5811, 0x1695, 0x9015, NULL, NULL, "EPoX", "EP-8RDA3+", board_epox_ep_8rda3plus}, @@ -1103,7 +1182,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x13f6, 0x0111, 0x1462, 0x5900, 0x1106, 0x3177, 0x1106, 0, "msi", "kt4ultra", "MSI", "MS-6590 (KT4 Ultra)",board_msi_kt4v}, {0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, NULL, NULL, "MSI", "MS-6702E (K8T Neo2-F)",w83627thf_gpio4_4_raise_2e}, {0x1106, 0x0571, 0x1462, 0x7120, 0, 0, 0, 0, "msi", "kt4v", "MSI", "MS-6712 (KT4V)", board_msi_kt4v}, - {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, "MSI", "MS-7046", ich6_gpio19_raise}, + {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, "MSI", "MS-7046", intel_ich_gpio19_raise}, {0x10de, 0x005e, 0, 0, 0, 0, 0, 0, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", w83627thf_gpio4_4_raise_4e}, {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, "Shuttle", "AK38N", it8705f_write_enable_2e}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, "Shuttle", "FN25", board_shuttle_fn25},
-
Luc Verhaegen