Stefan,
it would be nice if you could mail renesas and ask them for differences
in the firmware/flash access procedures between the uPD720200A and the uPD720201/uPD720202. if they are equal we might come up with something...<<
Renesas replied the following: "Renesas cannot assist or support such an effort. In addition, the programming interface for the uPD720200 and uPD720200A is different from the uPD720202, needs different programming tools, and relies on proprietary chip features that cannot be disclosed outside of Renesas."
please send us the output of lspci -nnxxxvv -d 1033:0194
run it as root please; else not the complete config space dump will be produced :) <<
root@PC02: lspci -nnxxxvv -d 1033:0194 03:00.0 USB Controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) (prog-if 30 [XHCI]) Subsystem: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at a0300000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=0 offset=00001000 PBA: BAR=0 offset=00001080 Capabilities: [a0] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd 00: 33 10 94 01 06 05 10 00 04 30 03 0c 08 00 00 00 10: 04 00 30 a0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 33 10 94 01 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 70 03 48 08 00 00 00 00 00 00 00 00 00 00 00 60: 30 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 05 90 86 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 11 a0 07 80 00 10 00 00 80 10 00 00 00 00 00 00 a0: 10 00 02 00 c0 8f 00 00 00 28 09 00 12 ec 07 00 b0: 00 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 10 08 00 00 00 00 00 00 00 00 00 00 d0: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: fc 1f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 08 14 60 00 00 00 00 00 00 00 00 00 00 00 00 00
Due to above, I am closing the file.
brgds
Philipp