i have attached flashrom's output below. patch is in the following mail. ======== DG45ID ======== ./flashrom -c "W25x32" -r ../testimages/dg45id.orig.img -VV Checking for a C compiler... found. Checking for libpci headers... found. Checking if libpci is present and sufficient... yes. Checking for FTDI support... not found. Checking for utsname support... found. flashrom v0.9.3-runknown on Linux 2.6.34-020634-generic (x86_64), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 2662M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 999 us, 10000 myus = 10028 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Intel Corporation" DMI string baseboard-product-name: "DG45ID" DMI string baseboard-version: "AAE27729-307" DMI string chassis-type: "Desktop" Found chipset "Intel ICH10R", enabling flash write... chipset PCI ID is 8086:3a16, 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2
Root Complex Register Block address = 0xfed1c000 GCS = 0xc1465: BIOS Interface Lock-Down: enabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) FLOCKDN 1, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x00000000 (FREG0: Flash Descriptor) 0x00000000-0x00000fff is read-only 0x58: 0x03ff0280 (FREG1: BIOS) 0x00280000-0x003fffff is read-write 0x5C: 0x027f0003 (FREG2: Management Engine) 0x00003000-0x0027ffff is locked 0x60: 0x00020001 (FREG3: Gigabit Ethernet) 0x00001000-0x00002fff is read-write 0x64: 0x00000fff (FREG4: Platform Data) 0x00fff000-0x00000fff is read-write 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00401000 (SSFS, SSFC) 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00004000 (FDOC) WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done preop0=0x06, preop1=0x00 op[0]=0x02, 3, 0 op[1]=0x03, 2, 0 op[2]=0x20, 3, 0 op[3]=0x05, 0, 0 op[4]=0x9f, 0, 0 op[5]=0x01, 1, 0 op[6]=0x00, 0, 0 op[7]=0x00, 0, 0 SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Probing for Winbond W25x32, 4096 kB: RDID returned 0xef 0x30 0x16. probe_spi_rdid_generic: id1 0xef, id2 0x3016 Chip status register is 00 Found chip "Winbond W25x32" (4096 kB, SPI) at physical address 0xffc00000. === This flash part has status UNTESTED for operations: READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... Transaction error SSFS SCIP=1, CDS=1, FCERR=1, AEL=1 | SSFC SCGO=1, ACS=1, SPOP=1, COP=7, DBC=63, SME=1, SCF=7 run OPCODE 0x03 failed at address 0x003000. Read operation failed! FAILED. Restoring PCI config space for 00:1f:0 reg 0xdc
=============== t410s ========== ./flashrom -Vfp internal:laptop=force_I_want_a_brick -r ../testimages/t410s.img -V -c "W25x64" flashrom v0.9.3-r1280 on Linux 2.6.35-27-generic (x86_64), built with libpci 3.1.7, GCC 4.4.5, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 1195M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10009 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "LENOVO" DMI string system-product-name: "2924W33" DMI string system-version: "ThinkPad T410s" DMI string baseboard-manufacturer: "LENOVO" DMI string baseboard-product-name: "2924W33" DMI string baseboard-version: "Not Available" DMI string chassis-type: "Notebook" Laptop detected via DMI ======================================================================== WARNING! You seem to be running flashrom on a laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Proceeding anyway because user specified laptop=force_I_want_a_brick Found chipset "Intel QS57", enabling flash write... chipset PCI ID is 8086:3b0f, 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x0 0xffe00000/0xffa00000 FWH IDSEL: 0x0 0xffd80000/0xff980000 FWH IDSEL: 0x0 0xffd00000/0xff900000 FWH IDSEL: 0x0 0xffc80000/0xff880000 FWH IDSEL: 0x0 0xffc00000/0xff800000 FWH IDSEL: 0x0 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x400000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0
Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, BOOT BIOS Straps: 0x3 (LPC) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) FLOCKDN 1, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 (FREG0: Flash Descriptor) 0x00000000-0x00000fff is read-only 0x58: 0x07ff0500 (FREG1: BIOS) 0x00500000-0x007fffff is read-write 0x5C: 0x04ff0003 (FREG2: Management Engine) 0x00003000-0x004fffff is locked 0x60: 0x00020001 (FREG3: Gigabit Ethernet) 0x00001000-0x00002fff is read-write 0x64: 0x00000fff (FREG4: Platform Data) 0x00fff000-0x00000fff is locked 0x74: 0x9fff07d0 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0xf87f100c (SSFS, SSFC) 0x94: 0x5006 (PREOP) 0x96: 0x143b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0601209f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000004 (FDOC) WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done preop0=0x06, preop1=0x50 op[0]=0x02, 3, 0 op[1]=0x03, 2, 0 op[2]=0x20, 3, 0 op[3]=0x05, 0, 0 op[4]=0x9f, 0, 0 op[5]=0x20, 1, 0 op[6]=0x01, 1, 0 op[7]=0x06, 0, 0 SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Probing for Winbond W25x64, 8192 kB: RDID returned 0xef 0x30 0x17. probe_spi_rdid_generic: id1 0xef, id2 0x3017 Chip status register is 00 Found chip "Winbond W25x64" (8192 kB, SPI) at physical address 0xff800000. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... Transaction error! SSFS: SCIP=1, FDONE=1, FCERR=1, AEL=1 | SSFC: SCGO=1, ACS=1, SPOP=1, COP=7, DBC=63, SME=1, SCF=7 run OPCODE 0x03 failed at address 0x003000. Read operation failed! FAILED. Restoring PCI config space for 00:1f:0 reg 0xdc
Stefan Tauner (1): add status of Thinkpad T410s and DG45ID to the wiki table
print.c | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-)