Re: [flashrom] [PATCH] Add Suport for Dr.Kaiser PC-Waechter

3 Sep 2009

      Hi,
Uwe Hermann schrieb:
...
...
Unrelated issue: My OpenSUSE 11.2 Beta Box needs
"make CFLAGS=-fno-strict-aliasing"
GCC is "gcc version 4.4.1 [gcc-4_4-branch revision 149935] (SUSE Linux)"
Can you post the full build output of your compiler here, so we can fix
the actual issue (so that fno-strict-aliasing is hopefully no longer
needed).
Here it is:
cc -Os -Wall -Werror  -D'SERPROG_SUPPORT=1'
-D'FLASHROM_VERSION="0.9.1-runknown"' -o physmap.o -c physmap.c
cc1: warnings being treated as errors
physmap.c: In function ârdmsrâ:
physmap.c:146: error: dereferencing type-punned pointer will break
strict-aliasing rules
make: *** [physmap.o] Fehler 1
This issue has already been reported on this list.
...
Please also send the output of 'lspci -vvvxxx' for reference, and the
output of a sample write operation of flashrom (flashrom -w foo.bin)
if possible. Thanks!
Both attached.
...
...
+#define PCI_MAGIC_DRKAISER_VALUE 0xA971
[...]
...

pci_write_word(pcidev_dev,PCI_MAGIC_DRKAISER_ADR, PCI_MAGIC_DRKAISER_VALUE);

Do you know if the magic value above is completely required? Maybe it's
just one of the bits in there that needs to be toggled? Theoretically
this could even be tested using the hardware (toggle one of the bits,
check if writing works; if not, toggle the next bit etc. etc.)
Checked all 2^16 combinations: Only the "magic" one works. All bits are
significant.
...
...

// Map 128KB Flash Memory Window
drkaiser_mem=physmap("Dr.Kaiser PC-Waechter FLASH Memory",
pci_read_long(pcidev_dev,PCI_BASE_ADDRESS_2), 128*1024);

Are you sure 128 KB is the maximum supported size here? The chip on your
board is 128KB, but maybe if bigger chips were soldered on instead they
would still work (depends on the FPGA, hardware wiring etc, I guess)?
All "Dr.Kaiser" Cars that I've seen so far have exactly the same Flash
chip, even the ones that are plugged into a socket (of the NIC version),
probably due to a limit of their original software.
-- J. Fischer
flashrom v0.9.1-runknown
Found "Dr. Kaiser PC-Waechter (Actel FPGA)" (1803:5057, BDF 00:0e.0).
Calibrating delay loop... OK.
Found chip "Macronix MX29F001B" (128 KB, Parallel) at physical address 0xfffe0000.
===
This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE
Please email a report to flashrom@flashrom.org if any of the above operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -rV,
-wV, -EV), and mention which mainboard you tested. Thanks for your help!
===
Flash image seems to be a legacy BIOS. Disabling checks.
Writing flash chip... Programming page: address: 0x00000000address: 0x00001000address: 0x00002000address: 0x00003000address: 0x00004000address: 0x00005000address: 0x00006000address: 0x00007000address: 0x00008000address: 0x00009000address: 0x0000a000address: 0x0000b000address: 0x0000c000address: 0x0000d000address: 0x0000e000address: 0x0000f000address: 0x00010000address: 0x00011000address: 0x00012000address: 0x00013000address: 0x00014000address: 0x00015000address: 0x00016000address: 0x00017000address: 0x00018000address: 0x00019000address: 0x0001a000address: 0x0001b000address: 0x0001c000address: 0x0001d000address: 0x0001e000address: 0x0001f000
COMPLETE.
Verifying flash... VERIFIED.
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx-
    Latency: 0
    Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
    Capabilities: [a0] AGP version 2.0
    	Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
    	Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: agpgart-via
00: 06 11 05 03 06 00 10 a2 02 00 00 06 00 00 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 17 a4 eb b4 46 0a 14 14 0c 80 00 00 08 10 14 14
60: 3c ba 00 20 d4 e6 e6 c4 50 28 65 2d 08 13 00 00
70: 46 88 cc 0c 0e 81 e2 00 01 b4 19 02 00 00 00 00
80: 0f 40 00 00 c0 00 00 00 03 00 5d 13 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 02 c0 20 00 17 02 00 1f 00 00 00 00 2f 02 14 00
b0: 62 db 20 85 31 33 3f 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 0e 22 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: d8000000-d9ffffff
    Prefetchable memory behind bridge: d4000000-d7ffffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
    	PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 05 83 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 c0 c0 00 00
20: 00 d8 f0 d9 00 d4 f0 d7 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
40: cb cd 08 44 25 72 05 83 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 02 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
    Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Kernel driver in use: parport_pc
00: 06 11 86 06 87 00 10 02 22 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 09 41 00 c0 00 80 60 a0 01 00 84 00 00 00 f0 f3
50: 0e 76 34 00 00 00 ab a0 00 06 ff 08 50 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 05 30 00 02 00 00 f0 40 00 00 00 00
80: 00 00 00 00 00 09 00 00 00 00 00 02 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32
    Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
    Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
    Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
    Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
    Region 4: I/O ports at d000 [size=16]
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: pata_via
00: 06 11 71 05 07 00 90 02 10 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
40: 03 e2 08 3a 08 10 c0 00 99 99 99 20 7f 00 a8 20
50: 0b 03 0b e0 14 00 00 00 a8 a8 a8 a8 00 00 00 00
60: 00 02 00 00 00 00 00 00 00 02 00 00 00 00 00 00
70: 02 01 00 00 00 00 00 00 82 01 00 00 00 00 00 00
80: 00 b0 73 12 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 71 05 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: First International Computer, Inc. VA-502 Mainboard
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32, Cache Line Size: 32 bytes
    Interrupt: pin D routed to IRQ 10
    Region 4: I/O ports at d400 [size=32]
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: uhci_hcd
00: 06 11 38 30 07 00 10 02 10 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 04 00 00
40: 00 10 03 00 c2 00 20 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: First International Computer, Inc. VA-502 Mainboard
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32, Cache Line Size: 32 bytes
    Interrupt: pin D routed to IRQ 10
    Region 4: I/O ports at d800 [size=32]
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: uhci_hcd
00: 06 11 38 30 07 00 10 02 10 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 04 00 00
40: 00 10 03 00 02 00 10 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin ? routed to IRQ 11
    Capabilities: [68] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 30 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
40: 20 84 5b 00 fa 30 00 00 01 40 00 00 00 10 00 00
50: 00 fe ff 88 50 00 00 00 00 fe ff 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 01 00 02 00 00 00 00 00
70: 01 60 00 00 01 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 01 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
    Subsystem: Analog Devices Device 5340
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin C routed to IRQ 10
    Region 0: I/O ports at dc00 [size=256]
    Region 1: I/O ports at e000 [size=4]
    Region 2: I/O ports at e400 [size=4]
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: VIA 82xx Audio
00: 06 11 58 30 01 00 10 02 20 00 01 04 00 00 00 00
10: 01 dc 00 00 01 e0 00 00 01 e4 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 d4 11 40 53
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 03 00 00
40: 01 cc 45 1c 00 00 00 00 00 00 00 02 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:09.0 Network controller: AVM GmbH A1 ISDN [Fritz] (rev 02)
    Subsystem: AVM GmbH FRITZ!Card ISDN Controller
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin A routed to IRQ 12
    Region 0: Memory at db043000 (32-bit, non-prefetchable) [size=32]
    Region 1: I/O ports at e800 [size=32]
00: 44 12 00 0a 03 01 80 02 02 00 80 02 00 00 00 00
10: 00 30 04 db 01 e8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 44 12 00 0a
30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0a.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
    Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32 (8000ns min, 16000ns max)
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at ec00 [size=256]
    Region 1: Memory at db042000 (32-bit, non-prefetchable) [size=256]
    [virtual] Expansion ROM at 14000000 [disabled] [size=128K]
    Capabilities: [50] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: 8139too
00: 13 11 11 12 07 00 90 02 10 00 00 02 00 20 00 00
10: 01 ec 00 00 00 20 04 db 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 13 11 11 12
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 c2 f7 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
    Subsystem: Advance Multimedia Internet Technology, Inc. Device 5312
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 10
    Region 0: Memory at db040000 (32-bit, non-prefetchable) [size=8K]
    Capabilities: [40] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: rt2500pci
00: 14 18 01 02 17 00 10 04 01 00 80 02 10 20 00 00
10: 00 00 04 db 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 06 00 00 eb 18 12 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
40: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0e.0 FLASH memory: ProdaSafe GmbH Device 5057 (rev 01)
    Subsystem: ProdaSafe GmbH Device 5057
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=256K]
    [virtual] Expansion ROM at 14020000 [disabled] [size=128K]
00: 03 18 57 50 03 00 00 02 01 00 01 05 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 db 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 03 18 57 50
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 71 a9 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS (prog-if 00 [VGA controller])
    Subsystem: ATI Technologies Inc Rage Fury Pro
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 32 (2000ns min), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 12
    Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
    Region 1: I/O ports at c000 [size=256]
    Region 2: Memory at d9000000 (32-bit, non-prefetchable) [size=16K]
    [virtual] Expansion ROM at d8000000 [disabled] [size=128K]
    Capabilities: [50] AGP version 2.0
    	Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
    	Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [5c] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 46 50 87 00 b0 02 00 00 00 03 08 20 00 00
10: 08 00 00 d4 01 c0 00 00 00 00 00 d9 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 04 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 01 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 5c 20 00 07 02 00 1f 00 02 00 00 01 00 02 02
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

Re: [flashrom] [PATCH] Add Suport for Dr.Kaiser PC-Waechter