On Sunday 29 May 2016 02:40 PM, David Hendricks wrote:
Hi Hatim, Interesting approach. It seems to work well for pretty printing, though I am curious how this will translate into ranges. Do you have an example for translating status_register_layout structs to a range of bytes protected, for example 0x000000-0x1fffff?
Hi,
I have been researching and developing ideas on how to go about block protection. A lot of this is based on Chromium OS' implementation. Here are the two models I have.
Before diving into the models themselves, here's idea that both models share. We define a struct range (just like Chromium OS) and then define an array struct range range[32]. We use the BP bitfield as indexes into the array - so a combination of BP4=0, BP3=0, BP2=1, BP1=0, BP0=1 gives a bitfield 0x05 and corresponding range is given by range[0x05]={start, len}. (32 because we have seen a maximum of 5 block protect bits so that is 2^5 = 32 combinations.) The obvious advantage is that status_to_range operations will happen in O(1) time. IMO, the use cases of reading the status register and translating BP bitfields into range are more than vice-versa. So IMHO having an array of ranges indexed by bitfield will certainly be more helpful. You will see that the two approaches differ in the implementation of this idea.
1. Block Protection Table The driving idea behind this model is to have a representation of block protection table in flashrom very similar to what is given in datasheets (just like Chromium OS currently has). But if we are to use array of ranges indexed by bitfield as per above idea, then we need to process this representation first. I came up with the following algorithm for translating the table into the range array -
translate_table_to_range(table): proc = [] done = [] for row in table proc.append(row) while proc is not empty tmp = proc.pop(0) for i = 0:5 if tmp.bp[i] is X new = tmp new.bp.replace(i, 0) proc.append(new) new.bp.replace(i, 1) proc.append(new) break if i is 5 done.append(tmp) for row in done index = row.bp4 << 4 | row.bp3 << 3 | row.bp1 << 1 |row.bp0 range[index] = row.range
These were the few questions came up immediately - - When do we call such a function in the code? Flashrom will always probe before performing any operation. So once the chip is found, we fetch the BP table from the struct flashchip, call this function, store the array of ranges, and then perform all future operations for that run using the array. - Do we call it for all the chips? IMO, calling this for all chips is a bad idea and the above answer makes this redundant. - How to handle corner cases? This needs to be dealt with still.
2. Array of Range This model is very simple compared to #1 - instead of any such processing, we simply represent the BP table in the form of an array of ranges in the first place. This might make representing the table in flashrom more cumbersome.
Attached is a prototype of the two models (both implementations are combined in the same file). I have extensively annotated the code to better convey the models defined above. The output is available here http://paste.flashrom.org/view.php?id=2921. Chromium implementation defines two separate structs from CMP=0 and CMP=1. This case can be handled automatically.
IMO, #2 is better than #1 and we should go forward with #2. The additional processing step that needs to be taken in #1 before array of ranges is available is what made me favour #2. I would like to hear your take on all this, particularly use cases (I could come up with only one or two, so please tell me more). There's a lot of comments in the code, so please go through those as well.
I am also wondering if it is possible to get the best of both #1 and #2 - is there a way to pre-process the BP Table into the array of ranges representation at the time of compilation itself for all chips? This would eliminate the additional step at runtime, and would make representation in the code easier.
Personally, I had a lot of fun implementing #1 mainly because it was a direct materialization of the algorithm and data structures theory I had in my course. I had started out developing my own data structures but then stopped mid-way and realized I should be looking for standard solutions. Then I found sys/queue.h. So, that was a nice learning experience!
Looking forward to your comments and feedback. Thanks for your time and patience.
Bye, Hatim