Author: stefanct Date: Sun Feb 8 22:57:52 2015 New Revision: 1879 URL: http://flashrom.org/trac/flashrom/changeset/1879
Log: Add a bunch of new/tested stuff and various small changes 22.
Tested mainboards: OK: - AOpen UK79G-1394 (used in EZ18 barebones) Reported by Lawrence Gough - ASUS M4N78 SE Reported by Dima Veselov - ASUS P5LD2-VM Mark board enable as tested (reported by Dima Veselov) - GIGABYTE GA-970A-UD3P (rev. 2.0) Reported by trucmar on IRC - GIGABYTE GA-990FXA-UD3 (rev. 4.0) Reported by ROKO__ on IRC - GIGABYTE GA-H77-DS3H (rev. 1.1) Reported by Evgeniy Edigarev - GIGABYTE GA-P55-USB3 (rev. 2.0) Reported by Måns Thörnqvist - MSI MS-7817 (H81M-E33) Reported by Igor Kolker
Chipsets: - Marked Intel Bay Trail (0x0f1c) as tested OK Reported by Antonio Ospite - Refine Intel IDs * Add IDs for Braswell * Add IDs for 9 Series PCHs (e.g. H97, Z97) * Rename Wellsburg devices slightly
Flash chips: - Atmel AT25DF041A to PREW (+PREW) Reported by Tai-hwa Liang - Atmel AT26DF161 to PREW (+EW) Reported by Steve Shenton - Atmel AT45DB011D to PREW (+PREW) Reported by The Raven - Atmel AT45DB642D to PREW (+PREW) Reported by Mahesh Mokal - Eon EN25F32 to PREW (+PREW) Reported by Arman Khodabande - Eon EN25F40 to PREW (+REW) Reported by Jerrad Pierce - Eon EN25QH16 to PREW (+EW) Reported by Ben Johnson - GigaDevice GD25Q20(B) to PREW (+PREW) Reported by Gilles Aurejac - Macronix MX25U6435E/F to PR (+PR) Reported by Matt Taggart - PMC Pm25LV512(A) to PREW (+PREW) Reported by The Raven - SST SST39VF020 to PREW (+PREW) Reported by Urja Rannikko - Winbond W25Q40.V to PREW (+EW) Reported by Torben Nielsen - Add E variants of MX25Lx006 (MX25L2006E, MX25L4006E, MX25L8006E). - Add MX25L6465E variant. - There was never a MX25L12805 AFAICT. - Split MX25L12805 from models with the same ID but an additional 32 kB eraser: MX25L12835F/MX25L12845E/MX25L12865E. - Add a bunch of ST parallel NOR flash chip IDs.
Miscellaneous: - Whitelist ThinkPad X200. - Constify master parameter of register_master(). - Remove FEATURE_BYTEWRITES because it was never used at all. - Refine hwseq messages and make them less prominent. - Fix the yet unused PRIxCHIPADDR format string thingy. - Fix copy&paste error in spi_prettyprint_status_register_bp(). Spotted by Pablo Cases. - Add an additional SMBus controller revision to identify another Yangtze model. Thanks to Dan Christensen for reporting this issue. - dediprog: add missing include for stdlib.h. This fixes (at least) building on FreeBSD and DragonflyBSD with gcc. - Remove references to struct pci_filter from programmer.h. It is only needed in internal.c where it has a complete type. Having it in programmer.h provokes a warning by some old versions of gcc. - Tiny other stuff.
Signed-off-by: Stefan Tauner stefan.tauner@alumni.tuwien.ac.at Acked-by: Stefan Tauner stefan.tauner@alumni.tuwien.ac.at
Modified: trunk/Makefile trunk/board_enable.c trunk/chipset_enable.c trunk/dediprog.c trunk/flash.h trunk/flashchips.c trunk/flashchips.h trunk/flashrom.8.tmpl trunk/flashrom.c trunk/ichspi.c trunk/nicintel_eeprom.c trunk/print.c trunk/programmer.c trunk/programmer.h trunk/sb600spi.c trunk/spi25_statusreg.c
Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/Makefile Sun Feb 8 22:57:52 2015 (r1879) @@ -138,7 +138,7 @@ else override CONFIG_PONY_SPI = no endif -# Dediprog and FT2232 are not supported under DOS (missing USB support). +# Dediprog, USB-Blaster and FT2232 are not supported under DOS (missing USB support). ifeq ($(CONFIG_DEDIPROG), yes) UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes else @@ -277,7 +277,7 @@ else override CONFIG_PONY_SPI = no endif -# Dediprog and FT2232 are not supported with libpayload (missing libusb support) +# Dediprog, USB-Blaster and FT2232 are not supported with libpayload (missing libusb support) ifeq ($(CONFIG_DEDIPROG), yes) UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes else @@ -914,6 +914,7 @@ endif
define FTDI_TEST +#include <stdlib.h> #include <ftdi.h> struct ftdi_context *ftdic = NULL; int main(int argc, char **argv)
Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/board_enable.c Sun Feb 8 22:57:52 2015 (r1879) @@ -2377,7 +2377,7 @@ {0x8086, 0x27b8, 0x1043, 0x2a22, 0x8086, 0x2770, 0x1043, 0x2a22, "^P5LP-LE$", NULL, NULL, P3, "ASUS", "P5LP-LE (Epson OEM)", 0, OK, intel_ich_gpio34_raise}, {0x8086, 0x27da, 0x1043, 0x8179, 0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2$", NULL, NULL, P3, "ASUS", "P5LD2", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x27da, 0x1043, 0x8179, 0x8086, 0x27b0, 0x1043, 0x8179, "^P5LD2-MQ$", NULL, NULL, P3, "ASUS", "P5LD2-MQ", 0, OK, intel_ich_gpio16_raise}, - {0x8086, 0x27da, 0x1043, 0x8179, 0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2-VM$", NULL, NULL, P3, "ASUS", "P5LD2-VM", 0, NT, intel_ich_gpio16_raise}, + {0x8086, 0x27da, 0x1043, 0x8179, 0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2-VM$", NULL, NULL, P3, "ASUS", "P5LD2-VM", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x27b0, 0x1043, 0x8179, 0x8086, 0x2770, 0x1043, 0x817a, "^P5LD2-VM DH$", NULL, NULL, P3, "ASUS", "P5LD2-VM DH", 0, OK, intel_ich_gpio16_raise}, {0x10DE, 0x0030, 0x1043, 0x818a, 0x8086, 0x100E, 0x1043, 0x80EE, NULL, NULL, NULL, P3, "ASUS", "P5ND2-SLI Deluxe", 0, OK, nvidia_mcp_gpio10_raise}, {0x10DE, 0x0260, 0x1043, 0x81BC, 0x10DE, 0x026C, 0x1043, 0x829E, "^P5N-D$", NULL, NULL, P3, "ASUS", "P5N-D", 0, OK, it8718f_gpio63_raise}, @@ -2427,6 +2427,7 @@ {0x8086, 0x1E22, 0x17AA, 0x21F6, 0x8086, 0x1E55, 0x17AA, 0x21F6, "^ThinkPad T530", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad T530", 0, OK, p2_whitelist_laptop}, {0x8086, 0x27a0, 0x17aa, 0x2015, 0x8086, 0x27b9, 0x17aa, 0x2009, "^ThinkPad T60", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad T60", 0, OK, p2_whitelist_laptop}, {0x8086, 0x27a0, 0x17aa, 0x2017, 0x8086, 0x27b9, 0x17aa, 0x2009, "^ThinkPad T60", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad T60(s)", 0, OK, p2_whitelist_laptop}, + {0x8086, 0x2917, 0x17AA, 0x20F5, 0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad X200$", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad X200", 0, OK, p2_whitelist_laptop}, {0x8086, 0x3B07, 0x17AA, 0x2166, 0x8086, 0x3B30, 0x17AA, 0x2167, "^Lenovo X201", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad X201", 0, OK, p2_whitelist_laptop}, {0x8086, 0x1E22, 0x17AA, 0x21FA, 0x8086, 0x1E55, 0x17AA, 0x21FA, "^ThinkPad X230", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad X230", 0, OK, p2_whitelist_laptop}, {0x8086, 0x27A0, 0x17AA, 0x2017, 0x8086, 0x27B9, 0x17AA, 0x2009, "^ThinkPad X60", NULL, NULL, P2, "IBM/Lenovo", "ThinkPad X60(s)", 0, OK, p2_whitelist_laptop},
Modified: trunk/chipset_enable.c ============================================================================== --- trunk/chipset_enable.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/chipset_enable.c Sun Feb 8 22:57:52 2015 (r1879) @@ -451,7 +451,7 @@ fwh_idsel_old = mmio_readl(ilb + fwh_sel1); rmmio_writel(fwh_idsel, ilb + fwh_sel1); } else { - fwh_idsel_old = pci_read_long(dev, fwh_sel1) << 16; + fwh_idsel_old = (uint64_t)pci_read_long(dev, fwh_sel1) << 16; rpci_write_long(dev, fwh_sel1, (fwh_idsel >> 16) & 0xffffffff); if (fwh_sel2 > 0) { fwh_idsel_old |= pci_read_word(dev, fwh_sel2); @@ -1593,7 +1593,7 @@ {0x1166, 0x0205, OK, "Broadcom", "HT-1000", enable_flash_ht1000}, {0x17f3, 0x6030, OK, "RDC", "R8610/R3210", enable_flash_rdc_r8610}, {0x8086, 0x0c60, NT, "Intel", "S12x0", enable_flash_s12x0}, - {0x8086, 0x0f1c, NT, "Intel", "Bay Trail", enable_flash_silvermont}, + {0x8086, 0x0f1c, OK, "Intel", "Bay Trail", enable_flash_silvermont}, {0x8086, 0x0f1d, NT, "Intel", "Bay Trail", enable_flash_silvermont}, {0x8086, 0x0f1e, NT, "Intel", "Bay Trail", enable_flash_silvermont}, {0x8086, 0x0f1f, NT, "Intel", "Bay Trail", enable_flash_silvermont}, @@ -1635,6 +1635,7 @@ {0x8086, 0x1f39, NT, "Intel", "Avoton/Rangeley", enable_flash_silvermont}, {0x8086, 0x1f3a, NT, "Intel", "Avoton/Rangeley", enable_flash_silvermont}, {0x8086, 0x1f3b, NT, "Intel", "Avoton/Rangeley", enable_flash_silvermont}, + {0x8086, 0x229c, NT, "Intel", "Braswell", enable_flash_silvermont}, {0x8086, 0x2310, NT, "Intel", "DH89xxCC (Cave Creek)", enable_flash_pch7}, {0x8086, 0x2390, NT, "Intel", "Coleto Creek", enable_flash_pch7}, {0x8086, 0x2410, OK, "Intel", "ICH", enable_flash_ich0}, @@ -1730,42 +1731,47 @@ {0x8086, 0x8c5d, NT, "Intel", "Lynx Point", enable_flash_pch8}, {0x8086, 0x8c5e, NT, "Intel", "Lynx Point", enable_flash_pch8}, {0x8086, 0x8c5f, NT, "Intel", "Lynx Point", enable_flash_pch8}, + {0x8086, 0x8cc1, NT, "Intel", "9 Series", enable_flash_pch9}, + {0x8086, 0x8cc2, NT, "Intel", "9 Series Engineering Sample", enable_flash_pch9}, + {0x8086, 0x8cc3, NT, "Intel", "9 Series", enable_flash_pch9}, + {0x8086, 0x8cc4, NT, "Intel", "Z97", enable_flash_pch9}, + {0x8086, 0x8cc6, NT, "Intel", "H97", enable_flash_pch9}, + {0x8086, 0x8d40, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d41, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d42, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d43, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d44, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d45, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d46, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d47, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d48, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d49, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4a, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4b, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4c, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4d, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4e, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d4f, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d50, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d51, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d52, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d53, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d54, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d55, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d56, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d57, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d58, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d59, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5a, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5b, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5c, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5d, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5e, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, + {0x8086, 0x8d5f, NT, "Intel", "C610/X99 (Wellsburg)", enable_flash_pch8_wb}, {0x8086, 0x9c41, NT, "Intel", "Lynx Point LP Eng. Sample", enable_flash_pch8_lp}, {0x8086, 0x9c43, NT, "Intel", "Lynx Point LP Premium", enable_flash_pch8_lp}, {0x8086, 0x9c45, NT, "Intel", "Lynx Point LP Mainstream", enable_flash_pch8_lp}, {0x8086, 0x9c47, NT, "Intel", "Lynx Point LP Value", enable_flash_pch8_lp}, - {0x8086, 0x8d40, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d41, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d42, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d43, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d44, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d45, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d46, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d47, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d48, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d49, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4a, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4b, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4c, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4d, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4e, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d4f, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d50, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d51, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d52, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d53, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d54, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d55, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d56, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d57, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d58, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d59, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5a, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5b, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5c, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5d, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5e, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, - {0x8086, 0x8d5f, NT, "Intel", "Wellsburg", enable_flash_pch8_wb}, {0x8086, 0x9cc1, NT, "Intel", "Haswell U Sample", enable_flash_pch9}, {0x8086, 0x9cc2, NT, "Intel", "Broadwell U Sample", enable_flash_pch9}, {0x8086, 0x9cc3, NT, "Intel", "Broadwell U Premium", enable_flash_pch9}, @@ -1807,10 +1813,10 @@ msg_pdbg(" with PCI ID %04x:%04x", chipset_enables[i].vendor_id, chipset_enables[i].device_id); - msg_pinfo(". "); + msg_pinfo(".\n");
if (chipset_enables[i].status == NT) { - msg_pinfo("\nThis chipset is marked as untested. If " + msg_pinfo("This chipset is marked as untested. If " "you are using an up-to-date version\nof " "flashrom *and* were (not) able to " "successfully update your firmware with it,\n"
Modified: trunk/dediprog.c ============================================================================== --- trunk/dediprog.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/dediprog.c Sun Feb 8 22:57:52 2015 (r1879) @@ -19,6 +19,7 @@
#include "platform.h"
+#include <stdlib.h> #include <stdio.h> #include <string.h> #include <limits.h>
Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/flash.h Sun Feb 8 22:57:52 2015 (r1879) @@ -107,7 +107,6 @@
/* Feature bits used for non-SPI only */ #define FEATURE_REGISTERMAP (1 << 0) -#define FEATURE_BYTEWRITES (1 << 1) #define FEATURE_LONG_RESET (0 << 4) #define FEATURE_SHORT_RESET (1 << 4) #define FEATURE_EITHER_RESET FEATURE_LONG_RESET
Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/flashchips.c Sun Feb 8 22:57:52 2015 (r1879) @@ -1276,7 +1276,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enhance (sic!) */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -1449,7 +1449,7 @@ .total_size = 512, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -2173,7 +2173,7 @@ .total_size = 2048, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -2435,7 +2435,7 @@ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */ .feature_bits = FEATURE_OTP, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_at45db, .probe_timing = TIMING_ZERO, .block_erasers = @@ -2772,7 +2772,7 @@ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */ .feature_bits = FEATURE_OTP, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_at45db, .probe_timing = TIMING_ZERO, .block_erasers = @@ -4220,7 +4220,7 @@ .total_size = 512, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_OK_PROBE, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -4325,7 +4325,7 @@ .total_size = 4096, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -4619,7 +4619,7 @@ /* OTP: 512B total; enter 0x3A */ /* QPI enable 0x38, disable 0xFF */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -5583,7 +5583,7 @@ .total_size = 256, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -6727,7 +6727,7 @@
{ .vendor = "Macronix", - .name = "MX25L2005(C)", + .name = "MX25L2005(C)/MX25L2006E", .bustype = BUS_SPI, .manufacture_id = MACRONIX_ID, .model_id = MACRONIX_MX25L2005, @@ -6765,7 +6765,7 @@
{ .vendor = "Macronix", - .name = "MX25L4005(A/C)", + .name = "MX25L4005(A/C)/MX25L4006E", .bustype = BUS_SPI, .manufacture_id = MACRONIX_ID, .model_id = MACRONIX_MX25L4005, @@ -6803,7 +6803,7 @@
{ .vendor = "Macronix", - .name = "MX25L8005/MX25V8005", + .name = "MX25L8005/MX25L8006E/MX25V8005", .bustype = BUS_SPI, .manufacture_id = MACRONIX_ID, .model_id = MACRONIX_MX25L8005, @@ -6907,7 +6907,7 @@ }, }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* MX25L1605A bp2 only */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, @@ -6942,7 +6942,7 @@ }, }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6: Continuously Program (CP) mode */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B), dual I/O supported */ .voltage = {2700, 3600}, @@ -6978,7 +6978,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, @@ -7014,7 +7014,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, @@ -7085,7 +7085,7 @@ }, }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6: CP mode */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and dual I/O supported */ .voltage = {2700, 3600}, @@ -7124,7 +7124,7 @@ }, }, .printlock = spi_prettyprint_status_register_bp3_srwd, - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and dual I/O supported */ .voltage = {2700, 3600}, @@ -7163,7 +7163,7 @@ }, }, .printlock = spi_prettyprint_status_register_bp3_srwd, - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and dual I/O supported */ .voltage = {2700, 3600}, @@ -7199,7 +7199,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -7235,7 +7235,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 has different meanings */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -7271,7 +7271,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 for 36E is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -7279,7 +7279,7 @@
{ .vendor = "Macronix", - .name = "MX25L6445E/MX25L6473E", + .name = "MX25L6445E/MX25L6465E/MX25L6473E", .bustype = BUS_SPI, .manufacture_id = MACRONIX_ID, .model_id = MACRONIX_MX25L6405, @@ -7311,7 +7311,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {2700, 3600}, @@ -7319,13 +7319,13 @@
{ .vendor = "Macronix", - .name = "MX25L12805(D)", + .name = "MX25L12805D", .bustype = BUS_SPI, .manufacture_id = MACRONIX_ID, - .model_id = MACRONIX_MX25L12805, + .model_id = MACRONIX_MX25L12805D, .total_size = 16384, .page_size = 256, - /* MX25L12805D has 64B of OTP; enter 0xB1, exit 0xC1 */ + /* OTP: 64B total; enter 0xB1, exit 0xC1 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -7347,9 +7347,49 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) supported */ + .voltage = {2700, 3600}, + }, + + { + .vendor = "Macronix", + .name = "MX25L12835F/MX25L12845E/MX25L12865E", + .bustype = BUS_SPI, + .manufacture_id = MACRONIX_ID, + .model_id = MACRONIX_MX25L12805D, + .total_size = 16384, + .page_size = 256, + /* OTP: 512B total; enter 0xB1, exit 0xC1 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 4096} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 512} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 256} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {16 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {16 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + /* TODO: security register and SBLK/SBULK; MX25L12835F: configuration register */ + .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, - .read = spi_chip_read, /* MX25L12805D: Fast read (0x0B) supported */ + .read = spi_chip_read, /* Fast read (0x0B) supported */ .voltage = {2700, 3600}, },
@@ -7364,7 +7404,7 @@ /* OTP: 512B total; enter 0xB1, exit 0xC1 */ /* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PR, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -7388,7 +7428,7 @@ }, /* TODO: security register */ .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {1650, 2000}, @@ -7430,7 +7470,7 @@ }, /* TODO: security register */ .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {1650, 2000}, @@ -7472,7 +7512,7 @@ }, /* TODO: security register */ .printlock = spi_prettyprint_status_register_bp3_srwd, /* bit6 is quad enable */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, /* Fast read (0x0B) and multi I/O supported */ .voltage = {1650, 2000}, @@ -8028,7 +8068,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8062,7 +8102,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_1, /* 128 */ .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8091,7 +8131,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8121,7 +8161,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_1, /* 128 */ .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8208,7 +8248,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8237,7 +8277,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, }, @@ -8265,7 +8305,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8294,7 +8334,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8323,7 +8363,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8352,7 +8392,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -8381,7 +8421,7 @@ } }, .printlock = spi_prettyprint_status_register_bp3_srwd, /* TODO: check */ - .unlock = spi_disable_blockprotect, + .unlock = spi_disable_blockprotect_bp3_srwd, .write = spi_chip_write_256, .read = spi_chip_read, .voltage = {2700, 3600}, @@ -9635,7 +9675,7 @@ .total_size = 64, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_res2, /* The continuation code is transferred as the 3rd byte m( */ .probe_timing = TIMING_ZERO, .block_erasers = @@ -12014,7 +12054,7 @@ .total_size = 256, .page_size = 4096, .feature_bits = FEATURE_EITHER_RESET, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_jedec, .probe_timing = 1, /* 150 ns */ .block_erasers = @@ -12898,7 +12938,7 @@ }, .block_erase = erase_block_82802ab, }, { - .eraseblocks = { {256 * 1024, 1}, }, + .eraseblocks = { {256 * 1024, 1} }, .block_erase = NULL, /* Only in A/A mux mode */ } }, @@ -13330,7 +13370,7 @@ /* supports SFDP */ /* OTP: 756B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, - .tested = TEST_OK_PR, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers =
Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/flashchips.h Sun Feb 8 22:57:52 2015 (r1879) @@ -27,7 +27,7 @@ /* * Please keep this list sorted alphabetically by manufacturer. The first * entry of each section should be the manufacturer ID, followed by the - * list of devices from that manufacturer (sorted by device IDs). + * list of devices from that manufacturer (sorted by device ID). * * Most LPC/FWH parts (parallel flash) have 8-bit device IDs if there is no * continuation code. @@ -303,6 +303,8 @@ #define EON_EN29LV010 0x7F6E #define EON_EN29LV040 0x4F /* Same as EN29LV040A */ #define EON_EN29LV640B 0xCB +#define EON_EN29LV640T 0xC9 +#define EON_EN29LV640U 0x7E #define EON_EN29F002T 0x7F92 /* Same as EN29F002A */ #define EON_EN29F002B 0x7F97 /* Same as EN29F002AN */ #define EON_EN29GL064HL 0x7E0C01 /* Uniform Sectors, WP protects Top OR Bottom sector */ @@ -466,13 +468,13 @@ * and use the same set of IDs. */ #define MACRONIX_MX25L512 0x2010 /* Same as MX25L512E, MX25V512, MX25V512C */ #define MACRONIX_MX25L1005 0x2011 /* Same as MX25L1005C, MX25L1006E */ -#define MACRONIX_MX25L2005 0x2012 /* Same as MX25L2005C */ -#define MACRONIX_MX25L4005 0x2013 /* Same as MX25L4005A, MX25L4005C */ -#define MACRONIX_MX25L8005 0x2014 /* Same as MX25V8005; FIXME: MX25L8073E (4k 0x20) */ +#define MACRONIX_MX25L2005 0x2012 /* Same as MX25L2005C, MX25L2006E */ +#define MACRONIX_MX25L4005 0x2013 /* Same as MX25L4005A, MX25L4005C, MX25L4006E */ +#define MACRONIX_MX25L8005 0x2014 /* Same as MX25V8005, MX25L8006E, FIXME: MX25L8073E (4k 0x20) */ #define MACRONIX_MX25L1605 0x2015 /* MX25L1605 (64k 0x20); MX25L1605A/MX25L1606E (4k 0x20, 64k 0x52); MX25L1605D/MX25L1608D/MX25L1673E (4k 0x20) */ #define MACRONIX_MX25L3205 0x2016 /* MX25L3205, MX25L3205A (64k 0x20); MX25L3205D/MX25L3208D (4k 0x20); MX25L3206E (4k 0x20, 64k 0x52); MX25L3273E (4k 0x20, 32k 0x52) */ -#define MACRONIX_MX25L6405 0x2017 /* MX25L6405, MX25L6405D (64k 0x20); MX25L6406E/MX25L6436E (4k 0x20); MX25L6445E/MX25L6473E (4k 0x20, 32k 0x52) */ -#define MACRONIX_MX25L12805 0x2018 /* Same as MX25L12805D, MX25L12835F, MX25L12845E (the latter two support completely new ID commands) */ +#define MACRONIX_MX25L6405 0x2017 /* MX25L6405, MX25L6405D (64k 0x20); MX25L6406E/MX25L6436E (4k 0x20); MX25L6445E/MX25L6465E/MX25L6473E (4k 0x20, 32k 0x52) */ +#define MACRONIX_MX25L12805D 0x2018 /* MX25L12805D (no 32k); MX25L12865E, MX25L12835F, MX25L12845E (32k 0x52) */ #define MACRONIX_MX25L25635F 0x2019 /* Same as MX25L25639F, but the latter seems to not support REMS */ #define MACRONIX_MX25L1635D 0x2415 #define MACRONIX_MX25L1635E 0x2515 /* MX25L1635{E} */ @@ -784,6 +786,48 @@ #define ST_M29W010B 0x23 #define ST_M29W040B 0xE3 #define ST_M29W512B 0x27 +#define ST_M28W160ECB 0x88CF +#define ST_M28W160ECT 0x88CE +#define ST_M28W320FCB 0x88BB +#define ST_M28W320FCT 0x88BA +#define ST_M28W640HCB 0x8849 +#define ST_M28W640HCT 0x8848 +#define ST_M29DW127G 0x7E2004 +#define ST_M29W128GH 0x7E2101 +#define ST_M29W128GL 0x7E2100 +#define ST_M29W160EB 0x2249 +#define ST_M29W160ET 0x22C4 +#define ST_M29W256GH 0x7E21xx +#define ST_M29W256GL 0x7E21xx +#define ST_M29W320DB 0x88CB +#define ST_M29W320DT 0x88CA +#define ST_M29W400FB 0x00EF +#define ST_M29W400FT 0x00EE +#define ST_M29W512GH 0x7E2301 +#define ST_M29W640FB 0x22FD +#define ST_M29W640FT 0x22ED +#define ST_M29W640GB 0x7E1000 +#define ST_M29W640GH 0x7E0C01 +#define ST_M29W640GL 0x7E0C00 +#define ST_M29W640GT 0x7E1001 +#define ST_M29W800FB 0x225B +#define ST_M29W800FT 0x22D7 +#define ST_M58BW16FB 0x8839 +#define ST_M58BW16FT 0x883A +#define ST_M58BW32FB 0x8837 +#define ST_M58BW32FT 0x8838 +#define ST_M58WR016KB 0x8813 +#define ST_M58WR016KT 0x8812 +#define ST_M58WR032KB 0x8815 +#define ST_M58WR032KT 0x8814 +#define ST_M58WR064KB 0x8811 +#define ST_M58WR064KT 0x8810 +#define ST_MT28GU01G___1 0x88B0 +#define ST_MT28GU01G___2 0x88B1 +#define ST_MT28GU256___1 0x8901 +#define ST_MT28GU256___2 0x8904 +#define ST_MT28GU512___1 0x887E +#define ST_MT28GU512___2 0x8881 #define ST_N25Q016__1E 0xBB15 /* N25Q016, 1.8V, (uniform sectors expected) */ #define ST_N25Q032__3E 0xBA16 /* N25Q032, 3.0V, (uniform sectors expected) */ #define ST_N25Q032__1E 0xBB16 /* N25Q032, 1.8V, (uniform sectors expected) */
Modified: trunk/flashrom.8.tmpl ============================================================================== --- trunk/flashrom.8.tmpl Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/flashrom.8.tmpl Sun Feb 8 22:57:52 2015 (r1879) @@ -1094,6 +1094,8 @@ .br Joshua Roys .br +Ky[:o]sti M[:a]lkki +.br Luc Verhaegen .br Li-Ta Lo @@ -1140,7 +1142,7 @@ .br some others, please see the flashrom svn changelog for details. .br -All authors can be reached via email at flashrom@flashrom.org. +All still active authors can be reached via email at flashrom@flashrom.org. .PP This manual page was written by Uwe Hermann uwe@hermann-uwe.de, Carl-Daniel Hailfinger and others.
Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/flashrom.c Sun Feb 8 22:57:52 2015 (r1879) @@ -2020,7 +2020,7 @@ // ////////////////////////////////////////////////////////////
if (write_it && erase_and_write_flash(flash, oldcontents, newcontents)) { - msg_cerr("Uh oh. Erase/write failed."); + msg_cerr("Uh oh. Erase/write failed. "); if (read_all_first) { msg_cerr("Checking if anything has changed.\n"); msg_cinfo("Reading current flash chip contents... ");
Modified: trunk/ichspi.c ============================================================================== --- trunk/ichspi.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/ichspi.c Sun Feb 8 22:57:52 2015 (r1879) @@ -1195,7 +1195,7 @@ struct block_eraser *eraser;
total_size = hwseq_data.size_comp0 + hwseq_data.size_comp1; - msg_cdbg("Found %d attached SPI flash chip", + msg_cdbg("Hardware sequencing reports %d attached SPI flash chip", (hwseq_data.size_comp1 != 0) ? 2 : 1); if (hwseq_data.size_comp1 != 0) msg_cdbg("s with a combined"); @@ -1210,14 +1210,14 @@ erase_size_high = ich_hwseq_get_erase_block_size(boundary);
if (boundary == 0) { - msg_cdbg("There is only one partition containing the whole " + msg_cdbg2("There is only one partition containing the whole " "address space (0x%06x - 0x%06x).\n", 0, size_high-1); eraser->eraseblocks[0].size = erase_size_high; eraser->eraseblocks[0].count = size_high / erase_size_high; - msg_cdbg("There are %d erase blocks with %d B each.\n", + msg_cdbg2("There are %d erase blocks with %d B each.\n", size_high / erase_size_high, erase_size_high); } else { - msg_cdbg("The flash address space (0x%06x - 0x%06x) is divided " + msg_cdbg2("The flash address space (0x%06x - 0x%06x) is divided " "at address 0x%06x in two partitions.\n", 0, total_size-1, boundary); size_low = total_size - size_high;
Modified: trunk/nicintel_eeprom.c ============================================================================== --- trunk/nicintel_eeprom.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/nicintel_eeprom.c Sun Feb 8 22:57:52 2015 (r1879) @@ -275,7 +275,7 @@ .erase = nicintel_ee_erase, };
-static int nicintel_spi_shutdown(void *eecp) +static int nicintel_ee_shutdown(void *eecp) { uint32_t old_eec = *(uint32_t *)eecp; /* Request bitbanging and unselect the chip first to be safe. */ @@ -323,7 +323,7 @@ return 1; *eecp = eec;
- if (register_shutdown(nicintel_spi_shutdown, eecp)) + if (register_shutdown(nicintel_ee_shutdown, eecp)) return 1; }
Modified: trunk/print.c ============================================================================== --- trunk/print.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/print.c Sun Feb 8 22:57:52 2015 (r1879) @@ -141,7 +141,7 @@ msg_ginfo(" "); msg_gdbg("range [V]"); msg_ginfo("\n\n"); - msg_ginfo("(P = PROBE, R = READ, E = ERASE, W = WRITE)\n\n"); + msg_ginfo("(P = PROBE, R = READ, E = ERASE, W = WRITE, - = N/A)\n\n");
for (chip = flashchips; chip->name != NULL; chip++) { /* Don't print generic entries. */ @@ -403,12 +403,14 @@ for (i = 0; i < maxboardlen - strlen(b->name); i++) msg_ginfo(" ");
- if (b->working == OK) - msg_ginfo("OK "); - else if (b->working == NT) - msg_ginfo("NT "); - else - msg_ginfo("BAD "); + switch (b->working) { + case OK: msg_ginfo("OK "); break; + case NT: msg_ginfo("NT "); break; + case DEP: msg_ginfo("DEP "); break; + case NA: msg_ginfo("N/A "); break; + case BAD: + default: msg_ginfo("BAD "); break; + }
for (e = board_matches; e->vendor_name != NULL; e++) { if (strcmp(e->vendor_name, b->vendor) @@ -548,7 +550,8 @@ B("Albatron", "PM266A Pro", OK, "http://www.albatron.com.tw/English/Product/MB/pro_detail.asp?rlink=Overview&...", NULL), /* FIXME */ B("Alienware", "Aurora-R2", BAD, NULL, "Mainboard model is 0RV30W. Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("AOpen", "i945GMx-VFX", OK, NULL, "This is (also?) an OEM board from FSC (used in e.g. ESPRIMO Q5010 with designation D2544-B1)."), - B("AOpen", "vKM400Am-S", OK, "http://usa.aopen.com/products_detail.aspx?Auno=824", NULL), + B("AOpen", "UK79G-1394", OK, "http://global.aopen.com/products_detail.aspx?auno=9", "Used in EZ18 barebones"), + B("AOpen", "vKM400Am-S", OK, "http://global.aopen.com/products_detail.aspx?Auno=824", NULL), B("Artec Group","DBE61", OK, "http://wiki.thincan.org/DBE61", NULL), B("Artec Group","DBE62", OK, "http://wiki.thincan.org/DBE62", NULL), B("ASI", "MB-5BLMP", OK, "http://www.hojerteknik.com/winnet.htm", "Used in the IGEL WinNET III thin client."), @@ -644,6 +647,7 @@ B("ASUS", "M4A89GTD PRO", OK, "http://www.asus.com/Motherboards/AMD_AM3/M4A89GTD_PRO/", NULL), B("ASUS", "M4N68T V2", OK, "http://www.asus.com/Motherboards/AMD_AM3/M4N68T_V2/", NULL), B("ASUS", "M4N78 PRO", OK, "http://www.asus.com/Motherboards/AMD_AM2Plus/M4N78_PRO/", NULL), + B("ASUS", "M4N78 SE", OK, "http://www.asus.com/Motherboards/AMD_AM2Plus/M4N78_SE/", NULL), B("ASUS", "M5A78L-M LX", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/M5A78LM_LX/", "The MAC address of the onboard LAN NIC is stored in flash, hence overwritten by flashrom; see http://www.flashrom.org/pipermail/flashrom/2012-May/009200.html"), B("ASUS", "M5A97 (rev. 1.0)", OK, "http://www.asus.com/Motherboard/M5A97/", NULL), B("ASUS", "M5A99X EVO", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/M5A99X_EVO/", NULL), @@ -698,7 +702,7 @@ B("ASUS", "P5L-VM 1394", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LVM_1394/", NULL), B("ASUS", "P5LD2", OK, NULL, NULL), B("ASUS", "P5LD2-MQ", OK, "http://support.asus.com/download.aspx?SLanguage=en&p=8&s=12&m=Vi...", "Found in ASUS Vintage-PH2 barebones."), - B("ASUS", "P5LD2-VM", NT, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LD2VM/", "Untested board enable."), + B("ASUS", "P5LD2-VM", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LD2VM/", NULL), B("ASUS", "P5LD2-VM DH", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LD2VM_DH/", NULL), B("ASUS", "P5LP-LE (Lithium-UL8E)", OK, "http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00379616&tmp_task=p...", "This is an OEM board from HP."), B("ASUS", "P5LP-LE (Epson OEM)", OK, NULL, "This is an OEM board from Epson (e.g. Endeavor MT7700)."), @@ -824,6 +828,8 @@ B("GIGABYTE", "GA-965GM-S2 (rev. 2.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2617", NULL), B("GIGABYTE", "GA-965P-DS4", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2288", NULL), B("GIGABYTE", "GA-970A-D3P (rev. 1.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4642", NULL), + B("GIGABYTE", "GA-970A-UD3P (rev. 2.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=5194", "Primary flash chip is a Macronix MX25L3206E."), + B("GIGABYTE", "GA-990FXA-UD3 (rev. 4.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4672", NULL), B("GIGABYTE", "GA-A75M-UD2H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3928", NULL), B("GIGABYTE", "GA-B85M-D3H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4567", NULL), B("GIGABYTE", "GA-EP31-DS3L (rev. 2.1)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2964", NULL), @@ -833,6 +839,7 @@ B("GIGABYTE", "GA-H61M-D2-B3", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3773", NULL), B("GIGABYTE", "GA-H61M-D2H-USB3", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4004", NULL), B("GIGABYTE", "GA-H77-D3H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4141", "Does only work with -p internal:ich_spi_mode=hwseq due to an evil twin of MX25L6405 and ICH SPI lockdown."), + B("GIGABYTE", "GA-H77-DS3H (rev. 1.1)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4318", NULL), B("GIGABYTE", "GA-H77M-D3H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4388", NULL), B("GIGABYTE", "GA-K8N51GMF-9", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=1939", NULL), B("GIGABYTE", "GA-K8N51GMF", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=1950", NULL), @@ -853,6 +860,7 @@ B("GIGABYTE", "GA-MA790FX-DQ6", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2690", NULL), B("GIGABYTE", "GA-MA790GP-DS4H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2887", NULL), B("GIGABYTE", "GA-MA790XT-UD4P (rev. 1.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3010", NULL), + B("GIGABYTE", "GA-P55-USB3 (rev. 2.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3440", NULL), B("GIGABYTE", "GA-P55A-UD4 (rev. 1.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3436", NULL), B("GIGABYTE", "GA-P55A-UD7" , OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3324", NULL), B("GIGABYTE", "GA-P67A-UD3P", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3649", NULL), @@ -975,6 +983,7 @@ B("MSI", "MS-7756 (H77MA-G43)", OK, "http://www.msi.com/product/mb/H77MA-G43.html", NULL), B("MSI", "MS-7808 (B75MA-E33)", OK, "http://www.msi.com/product/mb/B75MA-E33.html", NULL), B("MSI", "MS-7816 (H87-G43)", OK, "http://www.msi.com/product/mb/H87-G43.html", NULL), + B("MSI", "MS-7817 (H81M-E33)", OK, "http://www.msi.com/product/mb/H81ME33.html", NULL), B("MSI", "MS-9830 (IM-945GSE-A, A9830IMS)", OK, "http://www.msi.com/product/ipc/IM-945GSE-A.html", NULL), B("NEC", "PowerMate 2000", OK, "http://support.necam.com/mobilesolutions/hardware/Desktops/pm2000/celeron/", NULL), B("Nokia", "IP530", OK, NULL, NULL), @@ -1131,7 +1140,7 @@ B("IBM/Lenovo", "ThinkPad T420", BAD, "http://www.thinkwiki.org/wiki/Category:T420", "Probing works (Macronix MX25L6405, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs) and ME is locked. Also, a Protected Range is locking the top range of the BIOS region (presumably the boot block)."), B("IBM/Lenovo", "ThinkPad T410s", BAD, "http://www.thinkwiki.org/wiki/Category:T410s", "Probing works (Winbond W25X64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs) and ME is locked. Also, a Protected Range is locking the top range of the BIOS region (presumably the boot block)."), B("IBM/Lenovo", "ThinkPad X1", BAD, "http://www.thinkwiki.org/wiki/Category:X1", "Probing works (ST M25PX64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs) and ME is locked. Also, a Protected Range is locking the top range of the BIOS region (presumably the boot block)."), - B("IBM/Lenovo", "ThinkPad T530", OK, "http://www.thinkwiki.org/wiki/Category:T530", "Works fine but only with coreboot (due to locked regions and additional PR restrictions)."), + B("IBM/Lenovo", "ThinkPad T530", DEP, "http://www.thinkwiki.org/wiki/Category:T530", "Works fine but only with coreboot (due to locked regions and additional PR restrictions)."), B("IBM/Lenovo", "ThinkPad 240", BAD, "http://www.stanford.edu/~bresnan//tp240.html", "Seems to (partially) work at first, but one block/sector cannot be written which then leaves you with a bricked laptop. Maybe this can be investigated and fixed in software later."), B("IBM/Lenovo", "3000 V100 TF05Cxx", OK, "http://www5.pc.ibm.com/europe/products.nsf/products?openagent&brand=Leno...", NULL), //B("MSI", "GT60-2OD", OK, "http://www.msi.com/product/nb/GT60_2OD.html", NULL), requires layout patches
Modified: trunk/programmer.c ============================================================================== --- trunk/programmer.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/programmer.c Sun Feb 8 22:57:52 2015 (r1879) @@ -119,7 +119,7 @@ int registered_master_count = 0;
/* This function copies the struct registered_master parameter. */ -int register_master(struct registered_master *mst) +int register_master(const struct registered_master *mst) { if (registered_master_count >= MASTERS_MAX) { msg_perr("Tried to register more than %i master "
Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/programmer.h Sun Feb 8 22:57:52 2015 (r1879) @@ -321,8 +321,6 @@ #define SUPERIO_VENDOR_WINBOND 0x2 #endif #if NEED_PCI == 1 -struct pci_filter; -struct pci_dev *pci_dev_find_filter(struct pci_filter filter); struct pci_dev *pci_dev_find_vendorclass(uint16_t vendor, uint16_t devclass); struct pci_dev *pci_dev_find(uint16_t vendor, uint16_t device); struct pci_dev *pci_card_find(uint16_t vendor, uint16_t device, @@ -691,7 +689,7 @@ }; extern struct registered_master registered_masters[]; extern int registered_master_count; -int register_master(struct registered_master *mst); +int register_master(const struct registered_master *mst);
/* serprog.c */ #if CONFIG_SERPROG == 1
Modified: trunk/sb600spi.c ============================================================================== --- trunk/sb600spi.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/sb600spi.c Sun Feb 8 22:57:52 2015 (r1879) @@ -141,7 +141,7 @@ } else if (rev == 0x16) { amd_gen = CHIPSET_BOLTON; msg_pdbg("Bolton detected.\n"); - } else if (rev >= 0x39 && rev <= 0x3A) { + } else if ((rev >= 0x39 && rev <= 0x3A) || rev == 0x42) { amd_gen = CHIPSET_YANGTZE; msg_pdbg("Yangtze detected.\n"); } else { @@ -498,7 +498,7 @@ free(arg);
/* TODO: we should not only look at IntegratedImcPresent (LPC Dev 20, Func 3, 40h) but also at - * IMCEnable(Strap) and Override EcEnable(Strap) (sb8xx, sb9xx?, a50: Misc_Reg: 80h-87h; + * IMCEnable(Strap) and Override EcEnable(Strap) (sb8xx, sb9xx?, a50, Bolton: Misc_Reg: 80h-87h; * sb7xx, sp5100: PM_Reg: B0h-B1h) etc. */ uint8_t reg = pci_read_byte(dev, 0x40); if ((reg & (1 << 7)) == 0) {
Modified: trunk/spi25_statusreg.c ============================================================================== --- trunk/spi25_statusreg.c Tue Jan 27 19:07:50 2015 (r1878) +++ trunk/spi25_statusreg.c Sun Feb 8 22:57:52 2015 (r1879) @@ -260,7 +260,7 @@ /* Fall through. */ case 4: msg_cdbg("Chip status register: Block Protect 4 (BP4) is %sset\n", - (status & (1 << 5)) ? "" : "not "); + (status & (1 << 6)) ? "" : "not "); case 3: msg_cdbg("Chip status register: Block Protect 3 (BP3) is %sset\n", (status & (1 << 5)) ? "" : "not ");