Use names for the commands and request types instead of magic numbers and remove some of the unnecessary unexplained arguments. Also, cleanup the nonsense code left over from RE. Most of it can not explained by official documentation and was recorded with ancient firmware/software.
Based on the following chromiumos changes: Change-Id: I80a0dcdf40eedc89da48fb2c54cd9d9fd13e6fa1 Change-Id: If61bac2c8194b3ec30a80422d871842c66f0cd74
Signed-off-by: Simon Glass sjg@chromium.org Signed-off-by: Stefan Tauner stefan.tauner@alumni.tuwien.ac.at Acked-by: Stefan Tauner stefan.tauner@alumni.tuwien.ac.at --- dediprog.c | 386 +++++++++++++++++++++---------------------------------------- 1 file changed, 132 insertions(+), 254 deletions(-)
diff --git a/dediprog.c b/dediprog.c index b45e061..ce7ff7a 100644 --- a/dediprog.c +++ b/dediprog.c @@ -2,6 +2,8 @@ * This file is part of the flashrom project. * * Copyright (C) 2010 Carl-Daniel Hailfinger + * Copyright (C) 2015 Simon Glass + * Copyright (C) 2015 Stefan Tauner * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -38,13 +40,14 @@
#define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 +#define REQTYPE_OTHER_OUT (USB_ENDPOINT_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER) /* 0x43 */ +#define REQTYPE_OTHER_IN (USB_ENDPOINT_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER) /* 0xC3 */ +#define REQTYPE_EP_OUT (USB_ENDPOINT_OUT | USB_TYPE_VENDOR | USB_RECIP_ENDPOINT) /* 0x42 */ +#define REQTYPE_EP_IN (USB_ENDPOINT_IN | USB_TYPE_VENDOR | USB_RECIP_ENDPOINT) /* 0xC2 */ static usb_dev_handle *dediprog_handle; static int dediprog_firmwareversion; static int dediprog_endpoint;
-#define DEDI_SPI_CMD_PAGEWRITE 0x1 -#define DEDI_SPI_CMD_AAIWRITE 0x4 - enum dediprog_leds { LED_INVALID = -1, LED_NONE = 0, @@ -54,6 +57,77 @@ enum dediprog_leds { LED_ALL = 7, };
+/* IO bits for CMD_SET_IO_LED message */ +enum dediprog_ios { + IO1 = 1 << 0, + IO2 = 1 << 1, + IO3 = 1 << 2, + IO4 = 1 << 3, +}; + +enum dediprog_cmds { + CMD_TRANSCEIVE = 0x01, + CMD_POLL_STATUS_REG = 0x02, + CMD_SET_VPP = 0x03, + CMD_SET_TARGET = 0x04, + CMD_READ_EEPROM = 0x05, + CMD_WRITE_EEPROM = 0x06, + CMD_SET_IO_LED = 0x07, + CMD_READ_PROG_INFO = 0x08, + CMD_SET_VCC = 0x09, + CMD_SET_STANDALONE = 0x0A, + CMD_GET_BUTTON = 0x11, + CMD_GET_UID = 0x12, + CMD_SET_CS = 0x14, + CMD_IO_MODE = 0x15, + CMD_FW_UPDATE = 0x1A, + CMD_FPGA_UPDATE = 0x1B, + CMD_READ_FPGA_VERSION = 0x1C, + CMD_SET_HOLD = 0x1D, + CMD_READ = 0x20, + CMD_WRITE = 0x30, + CMD_WRITE_AT45DB = 0x31, + CMD_NAND_WRITE = 0x32, + CMD_NAND_READ = 0x33, + CMD_SET_SPI_CLK = 0x61, + CMD_CHECK_SOCKET = 0x62, + CMD_DOWNLOAD_PRJ = 0x63, + CMD_READ_PRJ_NAME = 0x64, + // New protocol/firmware only + CMD_CHECK_SDCARD = 0x65, + CMD_READ_PRJ = 0x66, +}; + +enum dediprog_target { + FLASH_TYPE_APPLICATION_FLASH_1 = 0, + FLASH_TYPE_FLASH_CARD, + FLASH_TYPE_APPLICATION_FLASH_2, +}; + +enum dediprog_readmode { + READ_MODE_STD = 1, + READ_MODE_FAST = 2, + READ_MODE_ATMEL45 = 3, + READ_MODE_4B_ADDR_FAST = 4, + READ_MODE_4B_ADDR_FAST_0x0C = 5, /* New protocol only */ +}; + +enum dediprog_writemode { + WRITE_MODE_PAGE_PGM = 1, + WRITE_MODE_PAGE_WRITE = 2, + WRITE_MODE_1B_AAI = 3, + WRITE_MODE_2B_AAI = 4, + WRITE_MODE_128B_PAGE = 5, + WRITE_MODE_PAGE_AT26DF041 = 6, + WRITE_MODE_SILICON_BLUE_FPGA = 7, + WRITE_MODE_64B_PAGE_NUMONYX_PCM = 8, /* unit of length 512 bytes */ + WRITE_MODE_4B_ADDR_256B_PAGE_PGM = 9, + WRITE_MODE_32B_PAGE_PGM_MXIC_512K = 10, /* unit of length 512 bytes */ + WRITE_MODE_4B_ADDR_256B_PAGE_PGM_0x12 = 11, + WRITE_MODE_4B_ADDR_256B_PAGE_PGM_FLAGS = 12, +}; + + static int dediprog_firmwareversion = FIRMWARE_VERSION(0, 0, 0);
#if 0 @@ -86,8 +160,6 @@ static struct usb_device *get_device_by_vid_pid(uint16_t vid, uint16_t pid, unsi return NULL; }
-//int usb_control_msg(usb_dev_handle *dev, int requesttype, int request, int value, int index, char *bytes, int size, int timeout); - /* This function sets the GPIOs connected to the LEDs as well as IO1-IO4. */ static int dediprog_set_leds(int leds) { @@ -110,7 +182,8 @@ static int dediprog_set_leds(int leds) }
target_leds ^= 7; - int ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, target_leds, NULL, 0x0, DEFAULT_TIMEOUT); + int ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_SET_IO_LED, 0x09, target_leds, + NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { msg_perr("Command Set LED 0x%x failed (%s)!\n", leds, usb_strerror()); return 1; @@ -149,8 +222,8 @@ static int dediprog_set_spi_voltage(int millivolt) /* Wait some time as the original driver does. */ programmer_delay(200 * 1000); } - ret = usb_control_msg(dediprog_handle, 0x42, 0x9, voltage_selector, - 0xff, NULL, 0x0, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_SET_VCC, voltage_selector, 0, + NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { msg_perr("Command Set SPI Voltage 0x%x failed!\n", voltage_selector); @@ -180,13 +253,6 @@ static const struct dediprog_spispeeds spispeeds[] = { { NULL, 0x0 }, };
-/* After dediprog_set_spi_speed, the original app always calls - * dediprog_set_spi_voltage(0) and then - * dediprog_check_devicestring() four times in a row. - * After that, dediprog_command_a() is called. - * This looks suspiciously like the microprocessor in the SF100 has to be - * restarted/reinitialized in case the speed changes. - */ static int dediprog_set_spi_speed(unsigned int spispeed_idx) { if (dediprog_firmwareversion < FIRMWARE_VERSION(5, 0, 0)) { @@ -194,12 +260,13 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) return 0; }
- msg_pdbg("SPI speed is %s Hz\n", spispeeds[spispeed_idx].name); + const struct dediprog_spispeeds *spispeed = &spispeeds[spispeed_idx]; + msg_pdbg("SPI speed is %sHz\n", spispeed->name);
- int ret = usb_control_msg(dediprog_handle, 0x42, 0x61, spispeeds[spispeed_idx].speed, 0xff, + int ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_SET_SPI_CLK, spispeed->speed, 0xff, NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { - msg_perr("Command Set SPI Speed 0x%x failed!\n", spispeeds[spispeed_idx].speed); + msg_perr("Command Set SPI Speed 0x%x failed!\n", spispeed->speed); return 1; } return 0; @@ -235,7 +302,7 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, /* Command Read SPI Bulk. No idea which read command is used on the * SPI side. */ - ret = usb_control_msg(dediprog_handle, 0x42, 0x20, start % 0x10000, + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_READ, start % 0x10000, start / 0x10000, (char *)count_and_chunk, sizeof(count_and_chunk), DEFAULT_TIMEOUT); if (ret != sizeof(count_and_chunk)) { @@ -344,7 +411,7 @@ static int dediprog_spi_bulk_write(struct flashctx *flash, const uint8_t *buf, u /* Command Write SPI Bulk. No idea which write command is used on the * SPI side. */ - ret = usb_control_msg(dediprog_handle, 0x42, 0x30, start % 0x10000, start / 0x10000, + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_WRITE, start % 0x10000, start / 0x10000, (char *)count_and_cmd, sizeof(count_and_cmd), DEFAULT_TIMEOUT); if (ret != sizeof(count_and_cmd)) { msg_perr("Command Write SPI Bulk failed, %i %s!\n", ret, @@ -422,12 +489,12 @@ static int dediprog_spi_write(struct flashctx *flash, const uint8_t *buf,
static int dediprog_spi_write_256(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len) { - return dediprog_spi_write(flash, buf, start, len, DEDI_SPI_CMD_PAGEWRITE); + return dediprog_spi_write(flash, buf, start, len, WRITE_MODE_PAGE_PGM); }
static int dediprog_spi_write_aai(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len) { - return dediprog_spi_write(flash, buf, start, len, DEDI_SPI_CMD_AAIWRITE); + return dediprog_spi_write(flash, buf, start, len, WRITE_MODE_2B_AAI); }
static int dediprog_spi_send_command(struct flashctx *flash, @@ -439,29 +506,26 @@ static int dediprog_spi_send_command(struct flashctx *flash, int ret;
msg_pspew("%s, writecnt=%i, readcnt=%i\n", __func__, writecnt, readcnt); - /* Paranoid, but I don't want to be blamed if anything explodes. */ - if (writecnt > 16) { - msg_perr("Untested writecnt=%i, aborting.\n", writecnt); + if (writecnt > UINT16_MAX) { + msg_perr("Invalid writecnt=%i, aborting.\n", writecnt); return 1; } - /* 16 byte reads should work. */ - if (readcnt > 16) { - msg_perr("Untested readcnt=%i, aborting.\n", readcnt); + if (readcnt > UINT16_MAX) { + msg_perr("Invalid readcnt=%i, aborting.\n", readcnt); return 1; } - ret = usb_control_msg(dediprog_handle, 0x42, 0x1, 0xff, - readcnt ? 0x1 : 0x0, (char *)writearr, writecnt, - DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_TRANSCEIVE, 0, readcnt ? 0x1 : 0x0, + (char *)writearr, writecnt, DEFAULT_TIMEOUT); if (ret != writecnt) { msg_perr("Send SPI failed, expected %i, got %i %s!\n", writecnt, ret, usb_strerror()); return 1; } - if (!readcnt) + if (readcnt == 0) return 0; - memset(readarr, 0, readcnt); - ret = usb_control_msg(dediprog_handle, 0xc2, 0x01, 0xbb8, 0x0000, + + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_IN, CMD_TRANSCEIVE, 0, 0, (char *)readarr, readcnt, DEFAULT_TIMEOUT); if (ret != readcnt) { msg_perr("Receive SPI failed, expected %i, got %i %s!\n", @@ -477,27 +541,27 @@ static int dediprog_check_devicestring(void) int fw[3]; char buf[0x11];
+#if 0 /* Command Prepare Receive Device String. */ - memset(buf, 0, sizeof(buf)); - ret = usb_control_msg(dediprog_handle, 0xc3, 0x7, 0x0, 0xef03, buf, - 0x1, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_OTHER_IN, 0x7, 0x0, 0xef03, + buf, 0x1, DEFAULT_TIMEOUT); /* The char casting is needed to stop gcc complaining about an always true comparison. */ if ((ret != 0x1) || (buf[0] != (char)0xff)) { msg_perr("Unexpected response to Command Prepare Receive Device" " String!\n"); return 1; } +#endif /* Command Receive Device String. */ - memset(buf, 0, sizeof(buf)); - ret = usb_control_msg(dediprog_handle, 0xc2, 0x8, 0xff, 0xff, buf, - 0x10, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_EP_IN, CMD_READ_PROG_INFO, 0, 0, + buf, 0x10, DEFAULT_TIMEOUT); if (ret != 0x10) { msg_perr("Incomplete/failed Command Receive Device String!\n"); return 1; } buf[0x10] = '\0'; msg_pdbg("Found a %s\n", buf); - if (memcmp(buf, "SF100", 0x5)) { + if (memcmp(buf, "SF100", 0x5) != 0) { msg_perr("Device not a SF100!\n"); return 1; } @@ -515,24 +579,20 @@ static int dediprog_check_devicestring(void) return 0; }
-/* Command A seems to be some sort of device init. It is either followed by - * dediprog_check_devicestring (often) or Command A (often) or - * Command F (once). - */ -static int dediprog_command_a(void) +static int dediprog_device_init(void) { int ret; char buf[0x1];
memset(buf, 0, sizeof(buf)); - ret = usb_control_msg(dediprog_handle, 0xc3, 0xb, 0x0, 0x0, buf, - 0x1, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_OTHER_IN, 0x0B, 0x0, 0x0, + buf, 0x1, DEFAULT_TIMEOUT); if (ret < 0) { msg_perr("Command A failed (%s)!\n", usb_strerror()); return 1; } if ((ret != 0x1) || (buf[0] != 0x6f)) { - msg_perr("Unexpected response to Command A!\n"); + msg_perr("Unexpected response to init!\n"); return 1; } return 0; @@ -548,9 +608,8 @@ static int dediprog_command_b(void) int ret; char buf[0x3];
- memset(buf, 0, sizeof(buf)); - ret = usb_control_msg(dediprog_handle, 0xc3, 0x7, 0x0, 0xef00, buf, - 0x3, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, REQTYPE_OTHER_IN, 0x7, 0x0, 0xef00, + buf, 0x3, DEFAULT_TIMEOUT); if (ret < 0) { msg_perr("Command B failed (%s)!\n", usb_strerror()); return 1; @@ -565,120 +624,29 @@ static int dediprog_command_b(void) } #endif
-/* Command Chip Select is only sent after dediprog_check_devicestring, but not after every - * invocation of dediprog_check_devicestring. It is only sent after the first - * dediprog_command_a(); dediprog_check_devicestring() sequence in each session. - * Bit #1 of the value changes the chip select: 0 is target 1, 1 is target 2 and parameter target can be 1 or 2 - * respectively. We don't know how to encode "3, Socket" and "0, reference card" yet. On SF100 the vendor - * software "DpCmd 6.0.4.06" selects target 2 when requesting 3 (which is unavailable on that hardware). - */ -static int dediprog_chip_select(int target) +static int set_target_flash(enum dediprog_target target) { - int ret; - uint16_t value = ((target - 1) & 1) << 1; - msg_pdbg("Selecting target chip %i\n", target); - ret = usb_control_msg(dediprog_handle, 0x42, 0x4, value, 0x0, NULL, - 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command Chip Select failed (%s)!\n", usb_strerror()); + int ret = usb_control_msg(dediprog_handle, REQTYPE_EP_OUT, CMD_SET_TARGET, target, 0, + NULL, 0, DEFAULT_TIMEOUT); + if (ret != 0) { + msg_perr("set_target_flash failed (%s)!\n", usb_strerror()); return 1; } return 0; }
#if 0 -/* Very strange. Seems to be a programmer keepalive or somesuch. - * Wait unsuccessfully for timeout ms to read one byte. - * Is usually called after setting voltage to 0. - * Present in all logs with Firmware 2.1.1 and 3.1.8 - */ -static int dediprog_command_f(int timeout) +/* Returns true if the button is currently pressed. */ +static bool dediprog_get_button(void) { - int ret; - char buf[0x1]; - - memset(buf, 0, sizeof(buf)); - ret = usb_control_msg(dediprog_handle, 0xc2, 0x11, 0xff, 0xff, buf, - 0x1, timeout); - /* This check is most probably wrong. Command F always causes a timeout - * in the logs, so we should check for timeout instead of checking for - * success. - */ - if (ret != 0x1) { - msg_perr("Command F failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} - -/* Start/stop blinking? - * Present in eng_detect_blink.log with firmware 3.1.8 - * Preceded by Command J - */ -static int dediprog_command_g(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x03, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command G failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} - -/* Something. - * Present in all logs with firmware 5.1.5 - * Always preceded by Command Receive Device String - * Always followed by Command Set SPI Voltage nonzero - */ -static int dediprog_command_h(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x05, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command H failed (%s)!\n", usb_strerror()); + char buf[1]; + int ret = usb_control_msg(dediprog_handle, REQTYPE_EP_IN, CMD_GET_BUTTON, 0, 0, + buf, 0x1, DEFAULT_TIMEOUT); + if (ret != 0) { + msg_perr("Could not get button state (%s)!\n", usb_strerror()); return 1; } - return 0; -} - -/* Shutdown for firmware 5.x? - * Present in all logs with firmware 5.1.5 - * Often preceded by a SPI operation (Command Read SPI Bulk or Receive SPI) - * Always followed by Command Set SPI Voltage 0x0000 - */ -static int dediprog_command_i(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x06, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command I failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} - -/* Start/stop blinking? - * Present in all logs with firmware 5.1.5 - * Always preceded by Command Receive Device String on 5.1.5 - * Always followed by Command Set SPI Voltage nonzero on 5.1.5 - * Present in eng_detect_blink.log with firmware 3.1.8 - * Preceded by Command B in eng_detect_blink.log - * Followed by Command G in eng_detect_blink.log - */ -static int dediprog_command_j(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x07, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command J failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; + return buf[0] != 1; } #endif
@@ -730,28 +698,6 @@ static int parse_voltage(char *voltage) return millivolt; }
-static int dediprog_setup(long target) -{ - /* URB 6. Command A. */ - if (dediprog_command_a()) { - return 1; - } - /* URB 7. Command A. */ - if (dediprog_command_a()) { - return 1; - } - /* URB 8. Command Prepare Receive Device String. */ - /* URB 9. Command Receive Device String. */ - if (dediprog_check_devicestring()) { - return 1; - } - /* URB 10. Command Chip Select */ - if (dediprog_chip_select(target)) { - return 1; - } - return 0; -} - static const struct spi_master spi_master_dediprog = { .type = SPI_CONTROLLER_DEDIPROG, .max_data_read = MAX_DATA_UNSPECIFIED, @@ -767,13 +713,6 @@ static int dediprog_shutdown(void *data) { msg_pspew("%s\n", __func__);
-#if 0 - /* Shutdown on firmware 5.x */ - if (dediprog_firmwareversion == 5) - if (dediprog_command_i()) - return 1; -#endif - dediprog_firmwareversion = FIRMWARE_VERSION(0, 0, 0);
/* URB 28. Command Set SPI Voltage to 0. */ @@ -819,6 +758,7 @@ int dediprog_init(void) } free(spispeed); } + voltage = extract_programmer_param("voltage"); if (voltage) { millivolt = parse_voltage(voltage); @@ -914,90 +854,28 @@ int dediprog_init(void) return 1;
/* Perform basic setup. */ - if (dediprog_setup(target)) { + if (dediprog_device_init()) + return 1; + if (dediprog_check_devicestring()) return 1; - }
/* Set all possible LEDs as soon as possible to indicate activity. * Because knowing the firmware version is required to set the LEDs correctly we need to this after * dediprog_setup() has queried the device and set dediprog_firmwareversion. */ dediprog_set_leds(LED_ALL);
- /* After setting voltage and speed, perform setup again. */ - if (dediprog_set_spi_voltage(0) || dediprog_set_spi_speed(spispeed_idx) || dediprog_setup(target)) { - dediprog_set_leds(LED_ERROR); - return 1; - } - - /* URB 11. Command Set SPI Voltage. */ - if (dediprog_set_spi_voltage(millivolt)) { + /* Select target/socket, frequency and VCC. */ + if (set_target_flash(FLASH_TYPE_APPLICATION_FLASH_1) || + dediprog_set_spi_speed(spispeed_idx) || + dediprog_set_spi_voltage(millivolt)) { dediprog_set_leds(LED_ERROR); return 1; }
register_spi_master(&spi_master_dediprog);
- /* RE leftover, leave in until the driver is complete. */ -#if 0 - /* Execute RDID by hand if you want to test it. */ - dediprog_do_stuff(); -#endif - dediprog_set_leds(LED_NONE);
return 0; }
-#if 0 -/* Leftovers from reverse engineering. Keep for documentation purposes until - * completely understood. - */ -static int dediprog_do_stuff(void) -{ - char buf[0x4]; - /* SPI command processing starts here. */ - - /* URB 12. Command Send SPI. */ - /* URB 13. Command Receive SPI. */ - memset(buf, 0, sizeof(buf)); - /* JEDEC RDID */ - msg_pdbg("Sending RDID\n"); - buf[0] = JEDEC_RDID; - if (dediprog_spi_send_command(JEDEC_RDID_OUTSIZE, JEDEC_RDID_INSIZE, - (unsigned char *)buf, (unsigned char *)buf)) - return 1; - msg_pdbg("Receiving response: "); - print_hex(buf, JEDEC_RDID_INSIZE); - /* URB 14-27 are more SPI commands. */ - /* URB 28. Command Set SPI Voltage. */ - if (dediprog_set_spi_voltage(0x0)) - return 1; - /* URB 29-38. Command F, unsuccessful wait. */ - if (dediprog_command_f(544)) - return 1; - /* URB 39. Command Set SPI Voltage. */ - if (dediprog_set_spi_voltage(0x10)) - return 1; - /* URB 40. Command Set SPI Speed. */ - if (dediprog_set_spi_speed(0x2)) - return 1; - /* URB 41 is just URB 28. */ - /* URB 42,44,46,48,51,53 is just URB 8. */ - /* URB 43,45,47,49,52,54 is just URB 9. */ - /* URB 50 is just URB 6/7. */ - /* URB 55-131 is just URB 29-38. (wait unsuccessfully for 4695 (maybe 4751) ms)*/ - /* URB 132,134 is just URB 6/7. */ - /* URB 133 is just URB 29-38. */ - /* URB 135 is just URB 8. */ - /* URB 136 is just URB 9. */ - /* URB 137 is just URB 11. */ - - /* Command Start Bulk Read. Data is u16 blockcount, u16 blocksize. */ - /* Command Start Bulk Write. Data is u16 blockcount, u16 blocksize. */ - /* Bulk transfer sizes for Command Start Bulk Read/Write are always - * 512 bytes, rest is filled with 0xff. - */ - - return 0; -} -#endif