There is no surprise here since other similar motherboards from Gigabyte work.
Manufacturer: Gigabyte Model: GA-MA790XT-UD4P South bridge: AMD SB 750 Flash chip: Macronix MX25L8005
flashrom version: 0.9.3-r1205
I tested reading and writing, but did not test erasure separate from writing. A transcript follows.
------------------------------------------------------------------------ # ./flashrom --verbose --read $h/r/chw/mb/bios-dump-f4g flashrom v0.9.3-r1205 on Linux 2.6.32.8 (x86_64), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 1084M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1000 us, 10000 myus = 10009 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "GA-MA790XT-UD4P" DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "GA-MA790XT-UD4P" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8720. Found chipset "AMD SB700/SB710/SB750", enabling flash write... chipset PCI ID is 1002:439d, SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=4, SpiBridgeDisable=0, DropOneClkOnRd=0 NormSpeed is 33 MHz GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK SB700 IMC is not active. ROM strap override is not active OK. This chipset supports the following protocols: LPC,FWH,SPI. No IT87* serial flash segment enabled. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for Bright BM29F040, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Hyundai HY29F040A, 512 KB: skipped. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635E, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29F040, 512 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A.RES, 512 KB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xc4, id2 0x10, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Probing for Winbond W29C040/P, 512 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040(F)B, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040(F)C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xf4, id2 0xcf, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xc2, id2 0x13 Reading flash... done. # ls -l $h/r/chw/mb/bios-dump-f4g -rw-r--r-- 1 root root 1048576 2011-04-01 11:54 /home/ka/r/chw/mb/bios-dump-f4g # cmp $h/r/chw/mb/bios-dump-f4g $h/f/w/gigabyte-bios/M79XTUD4.F8g /home/ka/r/chw/mb/bios-dump-f4g /home/ka/f/w/gigabyte-bios/M79XTUD4.F8g differ: byte 61508, line 72 # time ./flashrom --read /tmp/bios-f4g flashrom v0.9.3-r1205 on Linux 2.6.32.8 (x86_64), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, ID 0x8720. Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Reading flash... done.
real 0m6.451s user 0m6.400s sys 0m0.050s # cmp /tmp/bios-f4g $h/r/chw/mb/bios-dump-f4g # time ./flashrom --write $h/f/w/gigabyte-bios/M79XTUD4.F8g flashrom v0.9.3-r1205 on Linux 2.6.32.8 (x86_64), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, ID 0x8720. Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash before programming... Erasing flash chip... SUCCESS. done. Programming flash... done. COMPLETE. Verifying flash... VERIFIED.
real 1m5.828s user 1m5.750s sys 0m0.040s # ./flashrom --read /tmp/bios-f8g flashrom v0.9.3-r1205 on Linux 2.6.32.8 (x86_64), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, ID 0x8720. Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Reading flash... done. # cmp /tmp/bios-f8g $h/f/w/gigabyte-bios/M79XTUD4.F8g # lspci -nnvvv 00:00.0 Host bridge [0600]: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part [1002:5958] Subsystem: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part [1002:5958] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 Region 3: Memory at <ignored> (64-bit, non-prefetchable) Capabilities: [c4] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00 Link Frequency 0: 1.6GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [40] HyperTransport: Retry Mode Capabilities: [54] HyperTransport: UnitID Clumping Capabilities: [9c] HyperTransport: #1a
00:02.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A) [1002:5978] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fbffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0700c Data: 4169 Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5958] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport
00:04.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port A) [1002:597a] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x2, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0700c Data: 4171 Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5958] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport
00:09.0 PCI bridge [0604]: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port E) [1002:597e] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0700c Data: 4179 Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5958] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode] [1002:4390] (prog-if 01) Subsystem: Giga-byte Technology Device [1458:b002] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3a) Subsystem: Giga-byte Technology Device [1458:4385] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology Device [1458:5002] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at fa00 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable- Address: 00000000 Data: 0000 Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383] Subsystem: Giga-byte Technology Device [1458:a102] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin ? routed to IRQ 16 Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=04, subordinate=04, sec-latency=64 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: fdb00000-fdbfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: 1.6GHz Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: amd64_edac_mod
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?>
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 VGA compatible controller [0300]: nVidia Corporation G96 [GeForce 9500 GT] [10de:0640] (rev a1) Subsystem: eVga.com. Corp. Device [3842:c958] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at ef00 [size=128] [virtual] Expansion ROM at fb000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [b4] Vendor Specific Information <?> Capabilities: [100] Virtual Channel <?> Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information <?> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb
02:00.0 SATA controller [0106]: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363] (rev 02) (prog-if 01) Subsystem: Giga-byte Technology Device [1458:b000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 5: Memory at fdafe000 (32-bit, non-prefetchable) [size=8K] Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Express (v1) Legacy Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Kernel driver in use: ahci
02:00.1 IDE interface [0101]: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO]) Subsystem: Giga-byte Technology Device [1458:b000] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at df00 [size=8] Region 1: I/O ports at de00 [size=4] Region 2: I/O ports at dd00 [size=8] Region 3: I/O ports at dc00 [size=4] Region 4: I/O ports at db00 [size=16] Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_jmicron
03:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller [11ab:4362] (rev 20) Subsystem: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller [11ab:4362] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 28 Region 0: Memory at fdefc000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at ce00 [size=256] [virtual] Expansion ROM at fdd00000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data <?> Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0700c Data: 4191 Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Advanced Error Reporting <?> Kernel driver in use: sky2
04:07.0 Communication controller [0780]: NetMos Technology PCI 1 port parallel adapter [9710:9805] (rev 01) Subsystem: LSI Logic / Symbios Logic Device [1000:0010] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at bf00 [size=8] Region 1: I/O ports at be00 [size=8] Region 2: I/O ports at bd00 [size=8] Region 3: I/O ports at bc00 [size=8] Region 4: I/O ports at bb00 [size=8] Region 5: I/O ports at ba00 [size=16] Kernel driver in use: parport_pc
# superiotool -deV superiotool r3844 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Found ITE IT8720F (id=0x8720, rev=0x5) at 0x2e No dump available for this Super I/O Environment controller (0x022d) Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff #