$ sudo flashrom -V flashrom v0.9.4-r1395 on Linux 3.0.4 (x86_64), built with libpci 3.1.7, GCC 4.5.3, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 649M loops per second, delay more than 10% too short (got 52% of expected delay), recalculating... 842M loops per second, delay more than 10% too short (got 66% of expected delay), recalculating... 597M loops per second, delay more than 10% too short (got 62% of expected delay), recalculating... 749M loops per second, delay more than 10% too short (got 74% of expected delay), recalculating... 822M loops per second, delay loop is unreliable, trying to continue 10 myus = 8 us, 100 myus = 64 us, 1000 myus = 646 us, 10000 myus = 6992 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "ALiveNF5-eSATA2+ " DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP65" with PCI ID 10de:0441. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom@flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:0446 at 00:01:1 MCP SPI BAR is at 0x00000000 MCP SPI is not used. Please send the output of "flashrom -V" to flashrom@flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. This chipset supports the following protocols: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Found Winbond flash chip "W39V040B" (512 kB, LPC) at physical address 0xfff80000. Lockout bits: Hardware bootblock locking (#TBL) is not active. Hardware remaining chip locking (#WP) is not active.. Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0x54 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0x54 === This flash part has status UNTESTED for operations: WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88