[flashrom] Board enable request: Asus S96F/Z96F laptop

22 Jan 2010


      Model: Asus ASmobile AS96F945GM1
BIOS: http://downloadmirror.intel.com/12628/eng/S96F1006.zip
Notes: 
This laptop shares bios with the Z96F, which is identical except it is fitted 
with an nvidia GPU.
The super I/O is an ITE 8510E as seen here: 
http://downloadmirror.intel.com/12628/ENG/README.TXT
Datasheet for IT8510E: http://tabletbook.ru/My_Doc/PDF/IT8510E.pdf
I ran superiotool with the attached patch for the device id, but it didn't 
pick it up. The following quote from the sheet might be at play here (haven't 
physically verified):
"I/O Base Address Configuration
Sampled at VSTBY power up reset.
No pull resistor: The register pair to access PNPCFG is 002Eh and 002Fh.
10K ohm external pull-up resistor on BADDR0: The register pair to access 
PNPCFG is 004Eh and 004Fh.
10K ohm external pull-up resistor on BADDR1: The register pair to access 
PNPCFG is determined by EC domain registers SWCBALR and SWCBAHR."
Inlined:
flashrom -V
lspci -nnvvvxxx
superiotool -deV
cat /dev/ioports
cat /dev/iomem
*** begin flashrom ***
flashrom v0.9.1-r880
No coreboot table found.
DMI string 0: "To Be Filled By O.E.M."
DMI string 1: "Z96F"
DMI string 2: "1.0"
DMI string 3: "To Be Filled By O.E.M."
DMI string 4: "Z96F"
DMI string 5: "1.00"
Found chipset "Intel ICH7M", enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode disabled
0xffe80000/0xffa80000 FWH decode disabled
0xffe00000/0xffa00000 FWH decode disabled
0xffd80000/0xff980000 FWH decode disabled
0xffd00000/0xff900000 FWH decode disabled
0xffc80000/0xff880000 FWH decode disabled
0xffc00000/0xff800000 FWH decode disabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x80000 bytes
BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0
Root Complex Register Block address = 0xfed1c000
GCS = 0xc60: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x3 (LPC)
Top Swap : not enabled
OK.
This chipset supports the following protocols: FWH.
Calibrating delay loop... 611M loops per second, 100 myus = 199 us. OK.
Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for ASD AE49F2008, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT26F004, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Eon EN25B05, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B05T, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B10, 128 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B10T, 128 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B20, 256 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B20T, 256 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B40, 512 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B40T, 512 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B80, 1024 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Eon EN25B16, 2048 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Eon EN25B32, 4096 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Eon EN25B64, 8192 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Eon EN25D16, 2048 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F05, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F10, 128 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F20, 256 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F40, 512 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F80, 1024 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F16, 2048 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for Eon EN25F32, 4096 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x21, id2 0xd0
Probing for Intel 82802AC, 1024 KB: Chip size 1024 kB is bigger than supported 
size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff
Probing for Macronix MX25L512, 64 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for PMC Pm39LV020, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for PMC Pm39LV040, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x39, id2 0x4d, id1 
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x21, id2 0xd0, id1 
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Sharp LHF00L04, 1024 KB: Chip size 1024 kB is bigger than 
supported size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_49lfxxxc: id1 0xff, id2 0xff
Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for SST SST25VF040B, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x39, id2 0x4d, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x1d, id2 0xe2, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x21, id2 0xd0, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x21, id2 0xd0
Probing for SST SST49LF008A, 1024 KB: Chip size 1024 kB is bigger than 
supported size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_jedec_common: id1 0xff, id2 0xff, id1 
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 KB: Chip size 1024 kB is bigger than 
supported size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_49lfxxxc: id1 0xff, id2 0xff
Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than 
supported size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_49lfxxxc: id1 0xff, id2 0xff
Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for ST M25P05-A, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P05.RES, 64 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P10-A, 128 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P10.RES, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for ST M25P20, 256 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P40, 512 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P40-old, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for ST M25P80, 1024 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P16, 2048 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P32, 4096 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P64, 8192 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M25P128, 16384 KB: skipped. Host bus type FWH and chip bus type 
SPI are incompatible.
Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH and chip bus type 
Parallel are incompatible.
Probing for ST M50FLW040A, 512 KB: Chip lacks correct probe timing 
information, using default 10mS/40uS. probe_jedec_common: id1 0x21, id2 0xd0, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 KB: Chip lacks correct probe timing 
information, using default 10mS/40uS. probe_jedec_common: id1 0x21, id2 0xd0, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 KB: Chip size 1024 kB is bigger than supported 
size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. Chip lacks correct probe timing information, 
using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity 
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 KB: Chip size 1024 kB is bigger than supported 
size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. Chip lacks correct probe timing information, 
using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity 
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0x39, id2 0x4d
Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported 
size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff
Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x21, id2 0xd0
Probing for ST M50FW080, 1024 KB: Chip size 1024 kB is bigger than supported 
size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff
Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type FWH and chip 
bus type Parallel are incompatible.
Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W25x10, 128 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x20, 256 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x40, 512 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x80, 1024 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x16, 2048 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x32, 4096 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W25x64, 8192 KB: skipped. Host bus type FWH and chip bus 
type SPI are incompatible.
Probing for Winbond W29C011, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W29C020C, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W29C040P, 512 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W29EE011, 128 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x21, id2 0xd0, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for Winbond W49F002U, 256 KB: skipped. Host bus type FWH and chip bus 
type Parallel are incompatible.
Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH and chip bus 
type LPC are incompatible.
Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x39, id2 0x4d, 
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 KB: Chip size 1024 kB is bigger than 
supported size 512 kB of chipset/board/programmer for FWH interface, 
probe/read/erase/write may fail. Chip lacks correct probe timing information, 
using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity 
violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe 
timing information, using default 10mS/40uS. probe_jedec_common: id1 0x21, id2 
0xd0, id1 parity violation, id1 is normal flash content, id2 is normal flash 
content
Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type FWH and 
chip bus type SPI are incompatible.
Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type FWH and 
chip bus type SPI are incompatible.
Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type 
FWH and chip bus type SPI are incompatible.
Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type FWH and 
chip bus type SPI are incompatible.
Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type FWH and 
chip bus type SPI are incompatible.
Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type FWH and chip 
bus type SPI are incompatible.
Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type FWH and 
chip bus type SPI are incompatible.
Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type FWH 
and chip bus type SPI are incompatible.
Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type FWH 
and chip bus type SPI are incompatible.
No EEPROM/flash device found.
If you know which flash chip you have, and if this version of flashrom
supports a similar flash chip, you can try to force read your chip. Run:
flashrom -f -r -c similar_supported_flash_chip filename
Note: flashrom can never write when the flash chip isn't found automatically.
*** end flashrom ***
*** begin lspci ***
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML 
and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
    Subsystem: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT 
Express Memory Controller Hub [8086:27a0]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information <?>
    Kernel driver in use: agpgart-intel
    Kernel modules: intel-agp
00: 86 80 a0 27 06 00 90 20 03 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 a0 27
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 01 90 d1 fe 01 40 d1 fe 05 00 00 e0 01 80 d1 fe
50: 00 00 30 00 19 00 00 00 00 00 00 00 00 00 00 00
60: 01 30 d1 fe 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 10 11 11 00 00 33 33 00 ff 03 00 00 80 0a 38 00
a0: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 04 01 00 00
e0: 09 00 09 51 02 04 0a 90 0e 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 03 00 10 00 00 00
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 
943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-
if 00 [VGA controller])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1252]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at feb80000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at ec00 [size=8]
    Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at feb40000 (32-bit, non-prefetchable) [size=256K]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
    	Address: 00000000  Data: 0000
    Capabilities: [d0] Power Management version 2
    	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: i915
    Kernel modules: i915
00: 86 80 a2 27 07 00 90 00 03 00 00 03 00 00 80 00
10: 00 00 b8 fe 01 ec 00 00 08 00 00 d0 00 00 b4 fe
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 52 12
30: 00 00 00 00 90 00 00 00 00 00 00 00 05 01 00 00
40: 00 00 00 00 48 00 00 00 09 00 09 51 02 04 0a 90
50: 0e 00 30 00 19 00 00 00 00 00 00 00 00 00 80 7f
60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 05 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 03 00 64 34 00 00 00 00 86 0f 03 00 00 00 00 00
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1252]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]
    Capabilities: [d0] Power Management version 2
    	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 a6 27 07 00 90 00 03 00 80 03 00 00 80 00
10: 00 00 a8 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 52 12
30: 00 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 48 00 00 00 09 00 09 51 02 04 0a 90
50: 0e 00 30 00 19 00 00 00 00 00 00 00 00 00 80 7f
60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 03 00 64 34 00 00 00 00 86 0f 03 00 00 00 00 00
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High 
Definition Audio Controller [8086:27d8] (rev 02)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1343]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at feb38000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
    	Address: 0000000000000000  Data: 0000
    Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
    	DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
    		ExtTag- RBE- FLReset-
    	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
    		MaxPayload 128 bytes, MaxReadReq 128 bytes
    	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    	LnkCap:	Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 
<1us
    		ClockPM- Surprise- LLActRep- BwNot-
    	LnkCtl:	ASPM Disabled; Disabled- Retrain- CommClk-
    		ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    	LnkSta:	Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- 
ABWMgmt-
    Capabilities: [100] Virtual Channel <?>
    Capabilities: [130] Root Complex Link <?>
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel
00: 86 80 d8 27 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 80 b3 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 43 13
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00
40: 01 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 91 00 00 00 00 00 00 08 10 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express 
Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
    I/O behind bridge: 00001000-00001fff
    Memory behind bridge: 80000000-801fffff
    Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    	PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
    	DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 
unlimited
    		ExtTag- RBE- FLReset-
    	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    		MaxPayload 128 bytes, MaxReadReq 128 bytes
    	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    	LnkCap:	Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 
<4us
    		ClockPM- Surprise- LLActRep+ BwNot-
    	LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
    		ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    	LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- 
ABWMgmt-
    	SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
    		Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
    	SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    		Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
    	SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
    		Changed: MRL- PresDet- LinkState-
    	RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
    	RootCap: CRSVisible-
    	RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    	Address: fee0100c  Data: 4161
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Capabilities: [a0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100] Virtual Channel <?>
    Capabilities: [180] Root Complex Link <?>
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00: 86 80 d0 27 07 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 04 04 00 10 10 00 20
20: 00 80 10 80 21 80 31 80 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 02 00
40: 10 80 41 01 c0 0f 00 00 00 00 10 00 11 4c 11 01
50: 00 00 01 10 60 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 0c 10 e0 fe 61 41 00 00 00 00 00 00
90: 0d a0 00 00 43 10 47 13 00 00 00 00 00 00 00 00
a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 11 00 00 00 00 00
e0: 00 00 c7 00 06 07 08 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express 
Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
    I/O behind bridge: 00002000-00002fff
    Memory behind bridge: fe700000-fe7fffff
    Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    	PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
    	DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 
unlimited
    		ExtTag- RBE- FLReset-
    	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    		MaxPayload 128 bytes, MaxReadReq 128 bytes
    	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    	LnkCap:	Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 
<4us
    		ClockPM- Surprise- LLActRep+ BwNot-
    	LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
    		ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    	LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- 
ABWMgmt-
    	SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
    		Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
    	SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    		Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
    	SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
    		Changed: MRL- PresDet- LinkState-
    	RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
    	RootCap: CRSVisible-
    	RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    	Address: fee0100c  Data: 4169
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Capabilities: [a0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100] Virtual Channel <?>
    Capabilities: [180] Root Complex Link <?>
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00: 86 80 d2 27 07 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 20 20 00 00
20: 70 fe 70 fe 41 80 51 80 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 02 00
40: 10 80 41 01 c0 0f 00 00 00 00 10 00 11 2c 11 02
50: 42 00 11 30 60 00 00 00 00 00 40 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 0c 10 e0 fe 69 41 00 00 00 00 00 00
90: 0d a0 00 00 43 10 47 13 00 00 00 00 00 00 00 00
a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 11 00 00 00 00 00
e0: 00 00 c7 80 06 07 08 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express 
Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fdf00000-fe6fffff
    Prefetchable memory behind bridge: 00000000bdf00000-00000000bfefffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    	PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
    	DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 
unlimited
    		ExtTag- RBE- FLReset-
    	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    		MaxPayload 128 bytes, MaxReadReq 128 bytes
    	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    	LnkCap:	Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 
<4us
    		ClockPM- Surprise- LLActRep+ BwNot-
    	LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
    		ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    	LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- 
ABWMgmt-
    	SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
    		Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
    	SltCtl:	Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
    		Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
    	SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
    		Changed: MRL- PresDet- LinkState-
    	RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
    	RootCap: CRSVisible-
    	RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    	Address: fee0100c  Data: 4171
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Capabilities: [a0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100] Virtual Channel <?>
    Capabilities: [180] Root Complex Link <?>
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00: 86 80 d4 27 07 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 01 02 00 c0 c0 00 00
20: f0 fd 60 fe f1 bd e1 bf 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 03 02 00
40: 10 80 41 01 c0 0f 00 00 00 00 10 00 11 4c 11 03
50: 00 00 01 10 60 00 00 00 09 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 0c 10 e0 fe 71 41 00 00 00 00 00 00
90: 0d a0 00 00 43 10 47 13 00 00 00 00 00 00 00 00
a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 11 40 00 00 00 00
e0: 00 00 c7 00 06 07 08 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI 
Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 4: I/O ports at e400 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd
00: 86 80 c8 27 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e4 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI 
Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 4: I/O ports at e480 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd
00: 86 80 c9 27 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e4 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI 
Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 4: I/O ports at e800 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd
00: 86 80 ca 27 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI 
Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin D routed to IRQ 16
    Region 4: I/O ports at e880 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd
00: 86 80 cb 27 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e8 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 
EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at feb3fc00 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Kernel driver in use: ehci_hcd
    Kernel modules: ehci-hcd
00: 86 80 cc 27 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 fc b3 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 df 00 00 00 00 00 01 00 00 00 00 00 08 c0
70: 00 00 ff 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 11 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 aa ff 00 ff 00 ff 00 20 00 00 88
e0: 00 00 00 00 db b6 6d 00 00 00 00 00 00 00 00 00
f0: 00 80 00 09 88 85 40 00 86 0f 02 00 06 17 02 20
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge 
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fe800000-fe8fffff
    Prefetchable memory behind bridge: 0000000080600000-00000000806fffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    	PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
00: 86 80 48 24 07 01 10 00 e2 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 05 05 20 d0 d0 80 22
20: 80 fe 80 fe 61 80 61 80 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00
50: 0d 00 00 00 43 10 47 13 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface 
Bridge [8086:27b9] (rev 02)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information <?>
    Kernel modules: iTCO_wdt, intel-rng
00: 86 80 b9 27 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 80 00 00 00 81 04 00 00 10 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 0a 0b 07 d0 00 00 00 80 80 80 03 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 0f 2c 01 47 08 00 91 02 04 00 5d 02 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: a8 06 00 00 39 00 00 00 13 1c 04 00 00 03 00 00
b0: 00 00 f0 00 00 00 00 00 00 00 01 02 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 33 22 11 00 67 45 00 00 c0 80 00 00 01 00 00 00
e0: 09 00 0c 10 b4 02 24 17 00 00 00 00 00 00 00 00
f0: 01 c0 d1 fe 00 00 00 00 86 0f 02 00 00 00 00 00
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) 
SATA IDE Controller [8086:27c4] (rev 02) (prog-if 80 [Master])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at ffa0 [size=16]
    Capabilities: [70] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: ata_piix
00: 86 80 c4 27 05 00 b0 02 02 80 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 70 00 00 00 00 00 00 00 00 02 00 00
40: 00 80 37 e3 b0 00 00 00 0c 00 00 21 00 00 00 00
50: 00 00 00 00 c0 40 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 02 00 05 00 80 01 00 4a 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 0d 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller 
[8086:27da] (rev 02)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Interrupt: pin B routed to IRQ 19
    Region 4: I/O ports at 0400 [size=32]
    Kernel driver in use: i801_smbus
    Kernel modules: i2c-i801
00: 86 80 da 27 01 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG 
[Golan] Network Connection [8086:4222] (rev 02)
    Subsystem: Intel Corporation PRO/Wireless 3945ABG Network Connection 
[8086:1001]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 27
    Region 0: Memory at fe7ff000 (32-bit, non-prefetchable) [size=4K]
    Capabilities: [c8] Power Management version 2
    	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
    	Address: 00000000fee0100c  Data: 4189
    Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
    	DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
    		ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
    	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    		RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    		MaxPayload 128 bytes, MaxReadReq 128 bytes
    	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    	LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 
<64us
    		ClockPM+ Surprise- LLActRep- BwNot-
    	LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
    		ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    	LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- 
ABWMgmt-
    Capabilities: [100] Advanced Error Reporting
    	UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- 
ECRC- UnsupReq- ACSViol-
    	UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- 
ECRC- UnsupReq- ACSViol-
    	UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ 
ECRC- UnsupReq- ACSViol-
    	CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    	CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    	AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
    Capabilities: [140] Device Serial Number 00-19-d2-ff-ff-17-7a-09
    Kernel driver in use: iwl3945
    Kernel modules: iwl3945
00: 86 80 22 42 06 04 10 00 02 00 80 02 08 00 00 00
10: 00 f0 7f fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 01 10
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 01 d0 22 c8 00 00 00 0d
d0: 05 e0 81 00 0c 10 e0 fe 00 00 00 00 89 41 00 00
e0: 10 00 11 00 c0 0e 00 00 10 08 10 00 11 1c 07 00
f0: 42 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
05:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller 
[1180:0832] (prog-if 10 [OHCI])
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 64 (500ns min, 1000ns max)
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at fe8fe800 (32-bit, non-prefetchable) [size=2K]
    Capabilities: [dc] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+
    Kernel driver in use: ohci1394
00: 80 11 32 08 06 00 10 02 00 10 00 0c 00 40 80 00
10: 00 e8 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 02 04
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 80 80 16 00 00 04 00 00 20 00 00 66 66 32 12
90: 48 60 66 10 00 00 02 00 03 80 00 00 00 01 18 00
a0: 00 00 00 00 00 00 00 00 30 00 00 00 43 10 47 13
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 04
c0: 00 30 00 00 70 00 00 80 0f 00 00 81 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 c8
e0: 00 c0 00 48 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
05:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro 
Host Adapter [1180:0822] (rev 19)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 64
    Interrupt: pin B routed to IRQ 17
    Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
    Kernel driver in use: sdhci-pci
    Kernel modules: sdhci-pci
00: 80 11 22 08 06 00 10 02 19 00 05 08 00 40 80 00
10: 00 f0 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 fe 00 40 00 48 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
b0: 00 00 02 00 00 00 00 00 00 00 00 00 a0 00 00 00
c0: 00 30 00 00 70 00 00 80 0f 00 00 81 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: a1 21 80 01 00 00 00 00 40 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 c0 00 20 00 00 00 00 00
05:01.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller 
[1180:0843] (rev 01)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 10
    Region 0: Memory at fe8ff400 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
    Kernel driver in use: ricoh-mmc
    Kernel modules: ricoh_mmc
00: 80 11 43 08 06 00 10 02 01 00 80 08 00 00 80 00
10: 00 f4 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 fe 00 40 00 48 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
b0: 00 00 02 00 00 00 00 00 00 00 00 00 a0 00 00 00
c0: 00 30 00 00 70 00 00 80 0f 00 00 81 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 80 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00
05:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host 
Adapter [1180:0592] (rev 0a)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1347]
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Interrupt: pin B routed to IRQ 10
    Region 0: Memory at fe8ff800 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
00: 80 11 92 05 02 00 10 02 0a 00 80 08 00 00 80 00
10: 00 f8 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00
40: 00 00 02 00 00 00 00 00 00 00 02 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 fe 00 40 00 48 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 30 00 00 70 00 00 80 0f 00 00 81 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00
05:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. 
RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1345]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- 
SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
    Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 18
    Region 0: I/O ports at d800 [size=256]
    Region 1: Memory at fe8ffc00 (32-bit, non-prefetchable) [size=256]
    Expansion ROM at 80600000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: r8169
    Kernel modules: r8169
00: ec 10 67 81 17 00 b0 02 10 00 00 02 08 40 00 00
10: 01 d8 00 00 00 fc 8f fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 45 13
30: 00 00 8c fe dc 00 00 00 00 00 00 00 0b 01 20 40
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 c2 f7
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*** end lspci ***
*** begin superiotool ***
superiotool r4931
Probing for ALi Super I/O at 0x3f0...
  Failed. Returned data: id=0xffff, rev=0xff
Probing for ALi Super I/O at 0x370...
  Failed. Returned data: id=0xffff, rev=0xff
Probing for Fintek Super I/O at 0x2e...
  Failed. Returned data: vid=0xffff, id=0xffff
Probing for Fintek Super I/O at 0x4e...
  Failed. Returned data: vid=0xffff, id=0xffff
Probing for ITE Super I/O (init=standard) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=standard) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for NSC Super I/O at 0x2e...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x4e...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x15c...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
  Failed. Returned data: id=0xff, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
No Super I/O found
*** end superiotool ***
*** begin ioports ***
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0071 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.2
  0170-0177 : ata_piix
01f0-01f7 : 0000:00:1f.2
  01f0-01f7 : ata_piix
025c-025f : pnp 00:08
0320-0323 : wd7000
0350-0353 : wd7000
0376-0376 : 0000:00:1f.2
  0376-0376 : ata_piix
03c0-03df : vga+
03f6-03f6 : 0000:00:1f.2
  03f6-03f6 : ata_piix
0400-041f : 0000:00:1f.3
  0400-041f : i801_smbus
0480-04bf : 0000:00:1f.0
  0480-04bf : pnp 00:08
04d0-04d1 : pnp 00:08
0800-087f : 0000:00:1f.0
  0800-087f : pnp 00:08
    0800-0803 : ACPI PM1a_EVT_BLK
    0804-0805 : ACPI PM1a_CNT_BLK
    0808-080b : ACPI PM_TMR
    0810-0815 : ACPI CPU throttle
    0828-082f : ACPI GPE0_BLK
0cf8-0cff : PCI conf1
1000-1fff : PCI Bus 0000:04
2000-2fff : PCI Bus 0000:03
c000-cfff : PCI Bus 0000:01
d000-dfff : PCI Bus 0000:05
  d800-d8ff : 0000:05:07.0
    d800-d8ff : r8169
e400-e41f : 0000:00:1d.0
  e400-e41f : uhci_hcd
e480-e49f : 0000:00:1d.1
  e480-e49f : uhci_hcd
e800-e81f : 0000:00:1d.2
  e800-e81f : uhci_hcd
e880-e89f : 0000:00:1d.3
  e880-e89f : uhci_hcd
ec00-ec07 : 0000:00:02.0
ffa0-ffaf : 0000:00:1f.2
  ffa0-ffaf : ata_piix
*** end ioports ***
*** begin iomem ***
00000000-0000ffff : reserved
00010000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e0000-000fffff : reserved
  000f0000-000fffff : System ROM
00100000-7f7affff : System RAM
  01000000-0151d9d1 : Kernel code
  0151d9d2-016f0827 : Kernel data
  01763000-017cd343 : Kernel bss
7f7b0000-7f7bdfff : ACPI Tables
7f7be000-7f7effff : ACPI Non-volatile Storage
7f7f0000-7f7fffff : reserved
7f800000-7fffffff : RAM buffer
80000000-801fffff : PCI Bus 0000:04
80200000-803fffff : PCI Bus 0000:04
80400000-805fffff : PCI Bus 0000:03
80600000-806fffff : PCI Bus 0000:05
  80600000-8061ffff : 0000:05:07.0
8c000000-8c01ffff : pnp 00:08
bdf00000-bfefffff : PCI Bus 0000:01
d0000000-dfffffff : 0000:00:02.0
e0000000-e3ffffff : PCI MMCONFIG 0 [00-3f]
  e0000000-e3ffffff : pnp 00:0a
fdf00000-fe6fffff : PCI Bus 0000:01
fe700000-fe7fffff : PCI Bus 0000:03
  fe7ff000-fe7fffff : 0000:03:00.0
    fe7ff000-fe7fffff : iwl3945
fe800000-fe8fffff : PCI Bus 0000:05
  fe8fe800-fe8fefff : 0000:05:01.0
    fe8fe800-fe8fefff : ohci1394
  fe8ff000-fe8ff0ff : 0000:05:01.1
    fe8ff000-fe8ff0ff : mmc0
  fe8ff400-fe8ff4ff : 0000:05:01.2
  fe8ff800-fe8ff8ff : 0000:05:01.3
  fe8ffc00-fe8ffcff : 0000:05:07.0
    fe8ffc00-fe8ffcff : r8169
fea80000-feafffff : 0000:00:02.1
feb38000-feb3bfff : 0000:00:1b.0
  feb38000-feb3bfff : ICH HD audio
feb3fc00-feb3ffff : 0000:00:1d.7
  feb3fc00-feb3ffff : ehci_hcd
feb40000-feb7ffff : 0000:00:02.0
feb80000-febfffff : 0000:00:02.0
fec00000-fec00fff : IOAPIC 0
fed13000-fed19fff : pnp 00:01
fed1c000-fed1ffff : pnp 00:08
fed20000-fed3ffff : pnp 00:08
fed50000-fed8ffff : pnp 00:08
fee00000-fee00fff : Local APIC
  fee00000-fee00fff : reserved
    fee00000-fee00fff : pnp 00:09
ffb00000-ffbfffff : pnp 00:08
fff80000-ffffffff : reserved
*** end iomem ***

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

[flashrom] Board enable request: Asus S96F/Z96F laptop