On USB-based serial connections (VCP) the requested baud rate usually does not matter (much). Remove the arbitrary restriction and use whatever default values the OS/hardware provides.
Signed-off-by: Stefan Tauner stefan.tauner@alumni.tuwien.ac.at --- flashrom.8.tmpl | 26 ++++++++++++++------------ programmer.h | 4 +--- serial.c | 25 +++++++++++++++---------- serprog.c | 44 +++++++++++++++++++++++--------------------- 4 files changed, 53 insertions(+), 46 deletions(-)
diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl index 8b5f98c..26ea6e9 100644 --- a/flashrom.8.tmpl +++ b/flashrom.8.tmpl @@ -203,10 +203,9 @@ JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, \ Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA), TUMPA Lite, and GOEPEL PicoTAP. .sp -.BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog), \ -including AVR flasher by Urja Rannikko, AVR flasher by eightdot, \ -Arduino Mega flasher by fritz, InSystemFlasher by Juhana Helovuo, and \ -atmegaXXu2-flasher by Stefan Tauner." +.BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog, \ +including Arduino-based devices as well as various programmers by Urja Rannikko, \ +Juhana Helovuo, Stefan Tauner and others)." .sp .BR "* buspirate_spi" " (for SPI flash ROMs attached to a Bus Pirate)" .sp @@ -683,19 +682,22 @@ parameter with the syntax. .SS .BR "serprog " programmer -A mandatory parameter specifies either a serial -device/baud combination or an IP/port combination for communication with the -programmer. In the device/baud combination, the device has to start with a -slash. For serial, you have to use the +A mandatory parameter specifies either a serial device (and baud rate) or an IP/port combination for +communicating with the programmer. +The device/baud combination has to start with +.B dev= +and separate the optional baud rate with a colon. +For example .sp -.B " flashrom -p serprog:dev=/dev/device:baud" +.B " flashrom -p serprog:dev=/dev/ttyS0:115200" .sp -syntax and for IP, you have to use +If no baud rate is given the default values by the operating system/hardware will be used. +For IP connections you have to use the .sp .B " flashrom -p serprog:ip=ipaddr:port" .sp -instead. In case the device supports it, you can set the SPI clock frequency -with the optional +syntax. +In case the device supports it, you can set the SPI clock frequency with the optional .B spispeed parameter. The frequency is parsed as hertz, unless an .BR M ", or " k diff --git a/programmer.h b/programmer.h index 913522b..ea58e17 100644 --- a/programmer.h +++ b/programmer.h @@ -718,10 +718,8 @@ typedef int fdtype; #endif
void sp_flush_incoming(void); -fdtype sp_openserport(char *dev, unsigned int baud); -int serialport_config(fdtype fd, unsigned int baud); +fdtype sp_openserport(char *dev, int baud); extern fdtype sp_fd; -/* expose serialport_shutdown as it's currently used by buspirate */ int serialport_shutdown(void *data); int serialport_write(const unsigned char *buf, unsigned int writecnt); int serialport_write_nonblock(const unsigned char *buf, unsigned int writecnt, unsigned int timeout, unsigned int *really_wrote); diff --git a/serial.c b/serial.c index b216143..c9ce3af 100644 --- a/serial.c +++ b/serial.c @@ -116,7 +116,7 @@ static const struct baudentry sp_baudtable[] = { {0, 0} /* Terminator */ };
-const struct baudentry *round_baud(unsigned int baud) +static const struct baudentry *round_baud(unsigned int baud) { int i; /* Round baud rate to next lower entry in sp_baudtable if it exists, else use the lowest entry. */ @@ -125,11 +125,12 @@ const struct baudentry *round_baud(unsigned int baud) return &sp_baudtable[i];
if (sp_baudtable[i].baud < baud) { - msg_pinfo("Warning: given baudrate %d rounded down to %d.\n", + msg_pwarn("Warning: given baudrate %d rounded down to %d.\n", baud, sp_baudtable[i].baud); return &sp_baudtable[i]; } } + msg_pinfo("Using slowest possible baudrate: %d.\n", sp_baudtable[0].baud); return &sp_baudtable[0]; }
@@ -154,7 +155,7 @@ static void msg_perr_strerror(const char *msg) #endif }
-int serialport_config(fdtype fd, unsigned int baud) +int serialport_config(fdtype fd, int baud) { if (fd == SER_INV_FD) { msg_perr("%s: File descriptor is invalid.\n", __func__); @@ -167,8 +168,10 @@ int serialport_config(fdtype fd, unsigned int baud) msg_perr_strerror("Could not fetch original serial port configuration: "); return 1; } - const struct baudentry *entry = round_baud(baud); - dcb.BaudRate = entry->flag; + if (baud >= 0) { + const struct baudentry *entry = round_baud(baud); + dcb.BaudRate = entry->flag; + } dcb.ByteSize = 8; dcb.Parity = NOPARITY; dcb.StopBits = ONESTOPBIT; @@ -188,10 +191,12 @@ int serialport_config(fdtype fd, unsigned int baud) return 1; } wanted = observed; - const struct baudentry *entry = round_baud(baud); - if (cfsetispeed(&wanted, entry->flag) != 0 || cfsetospeed(&wanted, entry->flag) != 0) { - msg_perr_strerror("Could not set serial baud rate: "); - return 1; + if (baud >= 0) { + const struct baudentry *entry = round_baud(baud); + if (cfsetispeed(&wanted, entry->flag) != 0 || cfsetospeed(&wanted, entry->flag) != 0) { + msg_perr_strerror("Could not set serial baud rate: "); + return 1; + } } wanted.c_cflag &= ~(PARENB | CSTOPB | CSIZE | CRTSCTS); wanted.c_cflag |= (CS8 | CLOCAL | CREAD); @@ -232,7 +237,7 @@ int serialport_config(fdtype fd, unsigned int baud) return 0; }
-fdtype sp_openserport(char *dev, unsigned int baud) +fdtype sp_openserport(char *dev, int baud) { fdtype fd; #if IS_WINDOWS diff --git a/serprog.c b/serprog.c index 3de0182..4f671ce 100644 --- a/serprog.c +++ b/serprog.c @@ -342,26 +342,28 @@ int serprog_init(void) unsigned char rbuf[3]; unsigned char c; char *device; - char *baudport; int have_device = 0;
- /* the parameter is either of format "dev=/dev/device:baud" or "ip=ip:port" */ + /* the parameter is either of format "dev=/dev/device[:baud]" or "ip=ip:port" */ device = extract_programmer_param("dev"); if (device && strlen(device)) { - baudport = strstr(device, ":"); - if (baudport) { + char *baud_str = strstr(device, ":"); + if (baud_str) { /* Split device from baudrate. */ - *baudport = '\0'; - baudport++; + *baud_str = '\0'; + baud_str++; } - if (!baudport || !strlen(baudport)) { - msg_perr("Error: No baudrate specified.\n" - "Use flashrom -p serprog:dev=/dev/device:baud\n"); - free(device); - return 1; - } - if (strlen(device)) { - sp_fd = sp_openserport(device, atoi(baudport)); + int baud; + /* Convert baud string to value. + * baud_str is either NULL (if strstr can't find the colon), points to the \0 after the colon + * if no characters where given after the colon, or a string to convert... */ + if (baud_str == NULL || *baud_str == '\0') { + baud = -1; + msg_pdbg("No baudrate specified, using the hardware's defaults.\n"); + } else + baud = atoi(baud_str); // FIXME: replace atoi with strtoul + if (strlen(device) > 0) { + sp_fd = sp_openserport(device, baud); if (sp_fd == SER_INV_FD) { free(device); return 1; @@ -371,7 +373,7 @@ int serprog_init(void) } if (device && !strlen(device)) { msg_perr("Error: No device specified.\n" - "Use flashrom -p serprog:dev=/dev/device:baud\n"); + "Use flashrom -p serprog:dev=/dev/device[:baud]\n"); free(device); return 1; } @@ -386,20 +388,20 @@ int serprog_init(void) return 1; } if (device && strlen(device)) { - baudport = strstr(device, ":"); - if (baudport) { + char *port = strstr(device, ":"); + if (port) { /* Split host from port. */ - *baudport = '\0'; - baudport++; + *port = '\0'; + port++; } - if (!baudport || !strlen(baudport)) { + if (!port || !strlen(port)) { msg_perr("Error: No port specified.\n" "Use flashrom -p serprog:ip=ipaddr:port\n"); free(device); return 1; } if (strlen(device)) { - sp_fd = sp_opensocket(device, atoi(baudport)); + sp_fd = sp_opensocket(device, atoi(port)); if (sp_fd < 0) { free(device); return 1;