[flashrom] Re: Can't_erase_and_write_W25Q64BVDAIG_in_linux_only,read_O.K.

[Ivan Ivanov]

Well, I avoid SystemD too, so I'm using the distros like Void and
Artix (Arch without SystemD) - but never had a problem with flashrom.
Didn't try Devuan yet ( I prefer the newer versions of packages than
what Debian/Devuan stable could offer ) - but stuff like that may
happen even to the stablest distros, and also this issue could depend
on your local configuration and not reproducible i.e. on a fresh
Devuan install. Maybe try a Devuan LiveCD and see if it happens there
too?

Best regards,
Ivan Ivanov

вт, 17 янв. 2023 г. в 16:22, * :
> Hi,
> I’ve tried that (reinstal), same. Do you think Debian stable (Devuan stable) can make such broken library?
> Best regards.
> Alexey
>
> Вторник, 17 января 2023, 15:36 +03:00 от Ivan Ivanov :
>
> Hi there Alexey,
>
> Looks like you have a problem with your libusb library. Please
> reinstall the libusb library (you may have to build it from source, if
> your distro's libusb is broken at the moment - if that's so, make sure
> to --enable-shared).
>
> Best regards,
> Ivan Ivanov
>
> пн, 16 янв. 2023 г. в 23:54, * via flashrom :
> > Good day,
> >
> > Few days ago i've bought new Winbond W25Q64BVDAIG flash, getting errors during erasing or writing. Read is good. W25Q64FV... is errased and flashed well. W25Q64BVDAIG flashing works fine in WindowsXP by CH341A - USB Programmer 1.30. In Willem LPT Programmer set to 3.3V works fine too. CH341A - black.
> >
> > W25Q64BV... during error device stops respond with "run" led on, needs reinsert to USB to get it again.
> > ~$ sudo flashrom --programmer ch341a_spi -r Z77EXT62.90A.bin
> > [sudo] пароль для xxxxxx:
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Reading flash... done.
> > ~$ sudo flashrom --programmer ch341a_spi -r Z77EXT62.90A.rom
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Reading flash... done.
> > ~$ sudo flashrom --programmer ch341a_spi -E
> > [sudo] пароль для xxxxxx:
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Erasing and writing flash chip...
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 4265 bytes
> > Verification impossible because read failed at 0x17000 (len 0x1000)
> > ERASE FAILED!
> > Looking for another erase function.
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 34 bytes
> > spi_write_cmd failed during command execution at address 0x0
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> > Looking for another erase function.
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 34 bytes
> > spi_write_cmd failed during command execution at address 0x0
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> > Looking for another erase function.
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 34 bytes
> > spi_simple_write_cmd failed during command execution
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> > Looking for another erase function.
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 34 bytes
> > spi_simple_write_cmd failed during command execution
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> > Looking for another erase function.
> > Looking for another erase function.
> > Looking for another erase function.
> > No usable erase functions left.
> > FAILED!
> > Your flash chip is in an unknown state.
> > Please report this on IRC at chat.freenode.net (channel #flashrom) or
> > mail [e-mail], thanks!
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> > enable_pins: Failed to write 4 bytes
> > Could not disable output pins.
> > ~$ sudo flashrom --programmer ch341a_spi -w Z77EXT62.90A.bin -c "W25Q64.V"
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Reading old flash chip contents... done.
> > Erasing and writing flash chip...
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 34 bytes
> > spi_write_cmd failed during command execution at address 0x1500
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 36 bytes
> > RDSR failed!
> > Reading current flash chip contents...
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > ch341a_spi_spi_send_command: Failed to write 4265 bytes
> > Can't read anymore! Aborting.
> > FAILED!
> > Uh oh. Erase/write failed. Checking if anything has changed.
> > Reading current flash chip contents... ch341a_spi_spi_send_command: failed to submit IN transfer: LIBUSB_ERROR_BUSY
> > ch341a_spi_spi_send_command: Failed to read 4100 bytes
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> >
> > cb_in: error: LIBUSB_TRANSFER_TIMED_OUT
> > Can't even read anymore!
> > Your flash chip is in an unknown state.
> > Please report this on IRC at chat.freenode.net (channel #flashrom) or
> > mail [e-mail], thanks!
> >
> > cb_out: error: LIBUSB_TRANSFER_TIMED_OUT
> > enable_pins: Failed to write 4 bytes
> > Could not disable output pins.
> >
> > W25Q64FV... works just fine.
> > ~$ sudo flashrom --programmer ch341a_spi -E
> > [sudo] пароль для xxxxxx:
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Erasing and writing flash chip... Erase/write done.
> >
> > ~$ sudo flashrom --programmer ch341a_spi -w Z97EX62_80.bin -c "W25Q64.V"
> > flashrom v1.2 on Linux 5.10.0-17.1-liquorix-amd64 (x86_64)
> > flashrom is free software, get the source code at https://flashrom.org
> >
> > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
> > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on ch341a_spi.
> > Reading old flash chip contents... done.
> > Erasing and writing flash chip... Erase/write done.
> > Verifying flash... VERIFIED.`
> > Both chips are found as a "W25Q64.V".
> >
> > Best regards,
> > Alexey
> >
> > flashrom mailing list -- [e-mail]
> > To unsubscribe send an email to [e-mail]
>
> flashrom mailing list -- [e-mail]
> To unsubscribe send an email to [e-mail]