Re: [flashrom] VIA VT6421A (HZ-006)

[Roy]

2012/12/28 Stefan Tauner :
> On Thu, 27 Dec 2012 15:42:39 +0800
> Roy  wrote:
> > Hi all,
> >
> > It has "HZ-006" printed on the PCB. It does have Pm39LV512-70JCB on the
> > board, but it seems no firmware written and no boot ROM messages.
>
> Hello Roy,
>
> thanks for your report! I am collecting some facts about existing cards
> in our wiki: http://flashrom.org/VT6421A
> I have added the ones I know about your card and would like to add the
> remaining ones...
> > [=85]
> >
> > flashrom v0.9.6.1-r1564 on Linux 2.6.32-5-686 (i686)
> > flashrom is free software, get the source code at  
> > http://www.flashrom.or=

g
> > flashrom was built with libpci 3.1.7, GCC 4.4.5, little endian
> > Command line (3 args): ./flashrom -p atavia -V
> > Calibrating delay loop... OS timer resolution is 1 usecs, 261M loops per
> > second, delay more than 10% too short (got 87% of expected delay),
> > recalculating... 296M loops per second, 10 myus =3D 10 us, 100 myus =3D  
> > =

98 us,
> > 1000 myus =3D 986 us, 10000 myus =3D 9789 us, 4 myus =3D 5 us, OK.
> > Initializing atavia programmer
> > Found "VIA VT6421A" (1106:3249, BDF 00:0f.0).
> > =3D=3D=3D
> > This PCI device is UNTESTED. Please report the 'flashrom -p xxxx' output
> > to [e-mail] if it works for you. Please add the name of  
> > you=

r
> > PCI device to the subject. Thank you for your help!
> > =3D=3D=3D
> > Requested BAR is ROM
> > Error: No supported PCI device found.
>
> I am not entirely sure what happens there. Obviously pcidev_readbar
> reads 0... but we are not using that anyway and don't abort in that
> case AFAICS. There has been some discussion about refactor these parts
> and that would at least get rid of that message. I'll have to
> investigate and discuss this with my colleagues.
> What happens after that? flashrom exits?
> Can you please add -VVV to the command line and resend the resulting
> log?

Sure.

flashrom v0.9.6.1-r1564 on Linux 2.6.32-5-686 (i686)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.1.7, GCC 4.4.5, little endian
Command line (3 args): ./flashrom -p atavia -VVV
Calibrating delay loop... OS timer resolution is 1 usecs, 302M loops
per second, 10 myus =3D 10 us, 100 myus =3D 100 us, 1000 myus =3D 998 us,
10000 myus =3D 9996 us, 4 myus =3D 4 us, OK.
Initializing atavia programmer
Found "VIA VT6421A" (1106:3249, BDF 00:0f.0).
=3D=3D=3D
This PCI device is UNTESTED. Please report the 'flashrom -p xxxx' output
to [e-mail] if it works for you. Please add the name of your
PCI device to the subject. Thank you for your help!
=3D=3D=3D
PCI header type 0x00
Requested BAR is ROM
Error: No supported PCI device found.
>