2010/7/21 rayer rayer@seznam.cz
Thanks, I'll try... Please could you place the dos binary to some stable loacation so i could link it from my web?
What exactly is unstable about khepri ? Nothing, if you ask me :) Feel free to link to that download location.
Idwer
M,
Idwer Vollering wrote:
2010/7/21 Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.netmailto: c-d.hailfinger.devel.2006@gmx.net>
Speed up RayeR SPIPGM driver in flashrom by a factor of 2.
Allow specification of an alternate base port with flashrom -p rayer_spi:lptport=0x278 Any port number is allowed as long as it is nonzero, below 65536 and a multiple of four.
Untested, should work.
Martin, this one should hopefully reach the speed of SPIPGM.exe for reads. I'll ask Idwer to provide a DOS binary for you.
http://khepri.coresystems.de/~idwer/flashrom/r1093-patchwork-1666/http://khepri.coresystems.de/%7Eidwer/flashrom/r1093-patchwork-1666/< http://khepri.coresystems.de/%7Eidwer/flashrom/r1093-patchwork-1666/%3E
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net mailto:c-d.hailfinger.devel.2006@gmx.net>
Index: flashrom-bitbang_spi_rayer_faster/flashrom.8
--- flashrom-bitbang_spi_rayer_faster/flashrom.8 (Revision 1093) +++ flashrom-bitbang_spi_rayer_faster/flashrom.8 (Arbeitskopie) @@ -394,7 +394,18 @@ (in Hz). The default is the maximum frequency of 8 MHz. .TP .BR "rayer_spi " programmer -No parameters defined yet. More information about the hardware is available at +The default I/O base address used for the parallel port is 0x378 and you can use +the optional +.B lptport +parameter to specify an alternate base I/O address with the +.sp +.B " flashrom -p rayer_spi:lptport=portnum" +.sp +syntax where +.B portnum +is the I/O port number of your parallel port which must be a multiple of 4. +.sp +More information about the hardware is available at http://rayer.ic.cz/elektro/spipgm.htm .SH EXIT STATUS flashrom exits with 0 on success, 1 on most failures but with 2 if /dev/mem Index: flashrom-bitbang_spi_rayer_faster/rayer_spi.c =================================================================== --- flashrom-bitbang_spi_rayer_faster/rayer_spi.c (Revision 1093) +++ flashrom-bitbang_spi_rayer_faster/rayer_spi.c (Arbeitskopie) @@ -30,6 +30,7 @@ */ #if defined(__i386__) || defined(__x86_64__)
+#include <stdlib.h> #include "flash.h"
/* We have two sets of pins, out and in. The numbers for both
sets are @@ -42,7 +43,7 @@ /* Pins for slave->master direction */ #define SPI_MISO_PIN 6
-static int lpt_iobase; +static uint16_t lpt_iobase;
/* FIXME: All rayer_bitbang_set_* functions could use caching of
the value * stored at port lpt_iobase to avoid unnecessary INB. In theory, only one @@ -50,37 +51,31 @@ * value. */
-void rayer_bitbang_set_cs(int val) +/* Cached value of last byte sent. */ +static uint8_t lpt_outval;
+static void rayer_bitbang_set_cs(int val) {
uint8_t tmp;
tmp = INB(lpt_iobase);
tmp &= ~(1 << SPI_CS_PIN);
tmp |= (val << SPI_CS_PIN);
OUTB(tmp, lpt_iobase);
lpt_outval &= ~(1 << SPI_CS_PIN);
lpt_outval |= (val << SPI_CS_PIN);
OUTB(lpt_outval, lpt_iobase);
}
-void rayer_bitbang_set_sck(int val) +static void rayer_bitbang_set_sck(int val) {
uint8_t tmp;
tmp = INB(lpt_iobase);
tmp &= ~(1 << SPI_SCK_PIN);
tmp |= (val << SPI_SCK_PIN);
OUTB(tmp, lpt_iobase);
lpt_outval &= ~(1 << SPI_SCK_PIN);
lpt_outval |= (val << SPI_SCK_PIN);
OUTB(lpt_outval, lpt_iobase);
}
-void rayer_bitbang_set_mosi(int val) +static void rayer_bitbang_set_mosi(int val) {
uint8_t tmp;
tmp = INB(lpt_iobase);
tmp &= ~(1 << SPI_MOSI_PIN);
tmp |= (val << SPI_MOSI_PIN);
OUTB(tmp, lpt_iobase);
lpt_outval &= ~(1 << SPI_MOSI_PIN);
lpt_outval |= (val << SPI_MOSI_PIN);
OUTB(lpt_outval, lpt_iobase);
}
-int rayer_bitbang_get_miso(void) +static int rayer_bitbang_get_miso(void) { uint8_t tmp;
@@ -99,16 +94,49 @@
int rayer_spi_init(void) {
/* Pick a default value for now. */
lpt_iobase = 0x378;
char *portpos = NULL;
/* Non-default port requested? */
portpos = extract_programmer_param("lptport");
if (portpos) {
char *endptr = NULL;
unsigned long tmp;
tmp = strtoul(portpos, &endptr, 0);
/* Port 0, port >0x1000, unaligned ports and
garbage strings
* are rejected.
*/
if (!tmp || (tmp >= 0x10000) || (tmp & 0x3) ||
(*endptr != '\0')) {
/* Using ports below 0x100 is a really bad
idea, and
* should only be done if no port between
0x100 and
* 0xfffc works due to routing issues.
*/
msg_perr("Error: lptport specified, but no
valid "
"port specified.\nPort must be a
multiple of "
"0x4 and lie between 0x100 and
0xfffc.\n");
free(portpos);
return 1;
} else {
lpt_iobase = (uint16_t)tmp;
msg_pinfo("Non-default I/O base requested.
This will "
"not change the hardware
settings.\n");
}
} else {
/* Pick a default value for the I/O base. */
lpt_iobase = 0x378;
}
free(portpos);
msg_pdbg("Using port 0x%x as I/O base for parallel port
access.\n", lpt_iobase);
get_io_perms();
/* 1 usec halfperiod delay for now. */
if (bitbang_spi_init(&bitbang_spi_master_rayer, 1))
/* Get the initial value before writing to any line. */
lpt_outval = INB(lpt_iobase);
/* Zero halfperiod delay. */
if (bitbang_spi_init(&bitbang_spi_master_rayer, 0)) return 1; buses_supported = CHIP_BUSTYPE_SPI;
flashrom mailing list flashrom@flashrom.org mailto:flashrom@flashrom.org