As Stefan points out, some decisions were made in ChromiumOS to avoid modifying generic code and (in theory) make upstreaming easier. The writeprotect stuff is the main example. We can re-visit some of those decisions and put some code in generic locations if it makes sense to do so.
I don't like the idea of using a FEATURE_SR2 bit - It doesn't describe the functionality it represents in a useful manner IMO. As you point out, reading SR2 needlessly can slow things down, especially for the common use case where we only really care about reading the busy bit. For the write protection use case, the exact layout of the status registers needs to be taken into account, not just whether SR2 is present or not since SR2 is not as well standardized. To make matters more complicated, Gigadevice GD25Q128 even has a 3rd status register which has a bit that defines the entire write-protection scheme. Also, some chips such as Spansion S25FS and S25FL series don't use status registers in the same manner as other chips and instead define a set of control registers with special opcodes to read/write them.
Also, as Stefan points out, the status register bits are relevant to 4B addressing and quad I/O in addition to write protection. The implementation details are non-uniform.
Consequently, I think we need a combination of #2 and #3. For #2, we'll have functions which read the status registers (but must be careful since reading SR2 and SR3 aren't standardized AFAIK). For #3 we can describe the functionality we desire in a reasonably generic way and add chip-specific helper functions to carry out the task regardless of where the bits we are interested in reside. I started going in this direction for ChromiumOS's writeprotect.c, but it's still a work in progress: https://chromium-review.googlesource.com/#/c/208271/ https://chromium-review.googlesource.com/#/c/259440/ https://chromium-review.googlesource.com/#/c/335822/ https://chromium-review.googlesource.com/#/c/335823/
tl;dr version: Overall I think we should just do the work of representing the status register bits in a generic way, as you describe in #3. It will be tedious at first, but many chips will be able to share the same accessor functions. It's very important to be flexible so that we don't end up with "square peg in a round hole" over-generalizing and relying too heavily on if-statements/switch statements (a mistake I made in the chromiumos sources).
On Tue, May 24, 2016 at 2:07 AM, Stefan Tauner < stefan.tauner@alumni.tuwien.ac.at> wrote:
On Tue, 24 May 2016 12:49:51 +0530 Hatim Kanchwala hatim@hatimak.me wrote:
Hi,
The GSoC coding period has started and I have been working on my first sub-project, adding support for 2nd status register. Most supported chips that have multiple registers (around 80%) have opcode 0x35 for reading SR2 and, opcode 0x01 for writing SR2. I have developed 3 models and would like to have some feedback on them.
- Integrate read/write SR2 with existing functions
PROPOSAL -
- Define a feature bit FEATURE_SR2
- spi_read_status_register(), defined in spi25_statusreg.c, additionally
reads second status register depending on FEATURE_SR2 bit for that flash
- Change return to uint16_t for spi_read_status_register()
- spi_write_status_register_flag(), defined in spi25_statusreg.c,
considers higher byte of status to write to SR2, depending on FEATURE_SR2 bit for that flash. MERITS -
- Fits in elegantly with existing implementation (IMO). Most code in
flashrom stores status reads/writes in int, which can easily accommodate the 16 bits
- Very little hassle when editing struct flashchip in flashchips.c
DEMERITS -
- RDSR will take more time - will read SR2 even if not needed
- Define separate functions to read/write SR2
PROPOSAL -
- Define spi_read_status_register2() to read only SR2
- Define spi_write_status_register2_flag() and
spi_write_status_register2() to write to SR2. This will read SR1 first, then (SR2 << 8 | SR1) will be written using WRSR
MERITS -
- Flexibility (as compared to 1.)
DEMERITS -
- Need to write more lines (compared to 1.) when dealing with struct
flashchip
- struct status_register_layout
The ChromiumOS fork defines a struct status_register_layout in writeprotect.c, which contains only BP and SRP bits' information. PROPOSAL - Do a similar flashrom-wide definition, which contains all status register bits' information.
MERITS -
- Very detailed representation of information
DEMERITS -
- Too much work when adding support for new chips
- Overhaul of existing infrastructure
IMHO, the first model is the best among these 3. I would like to know what you guys think about these, whether you have some new idea. Looking forward to your feedback. Thanks for your time.
Hi,
thanks Hatim for this summary. It may make sense if David could sum up the rationales behind the chromiumos implementation. AFAIK much of that is driven by the desire to not touch flashchips.c to ease later upstreaming. A more detailed explanation might help Hatim.
What I miss from Hatim's proposals is how use cases affect the various implementations. The main question that needs to be addressed before implementing any kind of infrastructure like this is: what do we want to do with it once it is there.
Till now (vanilla) flashrom did only access the status registers for gathering (and printing) the status, especially the write protection bits, and for unlocking said bits. In the future we want to at least be able to set various protections additionally. What else do we need? Some bits are relevant to 4B addressing and Quad I/O too for example...
-- Kind regards/Mit freundlichen Grüßen, Stefan Tauner
flashrom mailing list flashrom@flashrom.org https://www.flashrom.org/mailman/listinfo/flashrom