Re: [flashrom] [PATCH] Full VIA SPI support

[Rudolf Marek]

Hi,
> case SPI_CONTROLLER_VIA:
> ichspi_bbar = mmio_readl(ich_spibar + 0x50)&  ~BBAR_MASK;
> if (ichspi_bbar)
> 	msg_pdbg("Reserved bits in BBAR not zero: 0x%04x",
> 		 ichspi_bbar);
> ichspi_bbar |= minaddr;

Why or?
> mmio_writel(ichspi_bbar, ich_spibar + 0x50);
> ichspi_bbar = mmio_readl(ich_spibar + 0x50);
> /* We don't have any option except complaining. */
> if (ichspi_bbar != minaddr)
> 	msg_perr("Setting BBAR failed!\n");
> break;
> case SPI_CONTROLLER_ICH9:
> mmio_writel(minaddr, ich_spibar + 0xA0);
> ichspi_bbar = mmio_readl(ich_spibar + 0xA0)&  ~BBAR_MASK;
> if (ichspi_bbar)
> 	msg_pdbg("Reserved bits in BBAR not zero: 0x%04x",
> 		 ichspi_bbar);
> ichspi_bbar |= minaddr;
> mmio_writel(ichspi_bbar, ich_spibar + 0xA0);
> ichspi_bbar = mmio_readl(ich_spibar + 0xA0);
> /* We don't have any option except complaining. */
> if (ichspi_bbar != minaddr)
> 	msg_perr("Setting BBAR failed!\n");
> break;
> default:
> /* Not sure if BBAR actually exists on VIA. */
> msg_pdbg("Setting BBAR is not implemented for VIA yet.\n");
> msg_perr("Unknown chipset for BBAR setting!\n");
> break;
> }
> }
>
> @@ -833,6 +845,7 @@
>    	    (writearr[2]<<  8) | (writearr[3]<<  0);
>    	switch (spi_controller) {
>    	case SPI_CONTROLLER_ICH7:
> case SPI_CONTROLLER_VIA:
> case SPI_CONTROLLER_ICH9:
> 	if (addr<  ichspi_bbar) {

Hope it works for 0 :) (yes it seems it works)
> 		msg_perr("%s: Address 0x%06x below allowed "
>
> @@ -1116,17 +1129,46 @@
>   int via_init_spi(struct pci_dev *dev)
>   {
>    uint32_t mmio_base;
>
> int i;
>
> mmio_base = (pci_read_long(dev, 0xbc))<<  8;
> msg_pdbg("MMIO base at = 0x%x\n", mmio_base);
> ich_spibar = physmap("VT8237S MMIO registers", mmio_base, 0x70);
> msg_pdbg("0x6c: 0x%04x     (CLOCK/DEBUG)\n",
>      mmio_readw(ich_spibar + 0x6c));
> /* Not sure if it speaks all these bus protocols. */
>  buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI;
>  spi_controller = SPI_CONTROLLER_VIA;
> msg_pdbg("0x00: 0x%04x     (SPIS)\n", mmio_readw(ich_spibar + 0));
> msg_pdbg("0x02: 0x%04x     (SPIC)\n", mmio_readw(ich_spibar + 2));
> msg_pdbg("0x04: 0x%08x (SPIA)\n", mmio_readl(ich_spibar + 4));
> for (i = 0; i<  2; i++) {
> int offs;
> offs = 8 + (i * 8);
> msg_pdbg("0x%02x: 0x%08x (SPID%d)\n", offs,
> 	 mmio_readl(ich_spibar + offs), i);
> msg_pdbg("0x%02x: 0x%08x (SPID%d+4)\n", offs + 4,
> 	 mmio_readl(ich_spibar + offs + 4), i);
> }
> ichspi_bbar = mmio_readl(ich_spibar + 0x50);
> msg_pdbg("0x50: 0x%08x (BBAR)\n", ichspi_bbar);
> msg_pdbg("0x54: 0x%04x     (PREOP)\n", mmio_readw(ich_spibar + 0x54));
> msg_pdbg("0x56: 0x%04x     (OPTYPE)\n", mmio_readw(ich_spibar + 0x56));
> msg_pdbg("0x58: 0x%08x (OPMENU)\n", mmio_readl(ich_spibar + 0x58));
> msg_pdbg("0x5c: 0x%08x (OPMENU+4)\n", mmio_readl(ich_spibar + 0x5c));
> for (i = 0; i<  3; i++) {
> int offs;
> offs = 0x60 + (i * 4);
> msg_pdbg("0x%02x: 0x%08x (PBR%d)\n", offs,
> 	 mmio_readl(ich_spibar + offs), i);
> }
> msg_pdbg("0x6c: 0x%04x     (CLOCK/DEBUG)\n",
>  mmio_readw(ich_spibar + 0x6c));

VT8237S has no bit 8, 12,13. We dont have to care about them anyway.
> if (mmio_readw(ich_spibar)&  (1<<  15)) {
> msg_pinfo("WARNING: SPI Configuration Lockdown activated.\n");
> ichspi_lock = 1;
> }

All good. Works:

Vendor ID: ASUS, part ID: M2V-MX SE
DMI string system-manufacturer: "Bochs"
DMI string system-product-name: "Bochs"
DMI string system-version: "Not Specified"
DMI string baseboard-manufacturer: ""
DMI string baseboard-product-name: ""
DMI string baseboard-version: ""
Mapping VT8237S MMIO registers at 0xfed02000, unaligned size 0x70.
DMI string chassis-type: "Other"
Found ITE Super I/O, ID 0x8712.
Found chipset "VIA VT8237S", enabling flash write... chipset PCI ID is 
1106:3372, MMIO base at = 0xfed02000
0x00: 0x0014     (SPIS)
0x02: 0x4140     (SPIC)
0x04: 0x00000000 (SPIA)
0x08: 0x1320377f (SPID0)
0x0c: 0x45564948 (SPID0+4)
0x10: 0xdabb0000 (SPID1)
0x14: 0x10000000 (SPID1+4)
0x50: 0x00000000 (BBAR)
0x54: 0x5006     (PREOP)
0x56: 0x462b     (OPTYPE)
0x58: 0x05ab0302 (OPMENU)
0x5c: 0xc79f0190 (OPMENU+4)
0x60: 0x00000000 (PBR0)
0x64: 0x00000000 (PBR1)
0x68: 0x00000000 (PBR2)
0x6c: 0x0000     (CLOCK/DEBUG)
Programming OPCODES...
program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190
done
OK.

Thanks,
Rudolf