flashrom

flashrom@flashrom.org

9164 discussions

Re: [flashrom] MX25L1605DM2I-12G with Buspirate
by Idwer Vollering 29 Nov '12

29 Nov '12

2012/11/29 Daniel . <phl3ckz(a)googlemail.com>: > Hi everyone, > > I am absolute beginner but I need to read and write the above mentioned > serial Flash memory. > > This is a BIOS chip and had a bad flash. Now it is unsoldered from > mainboard. How do you connect the buspirate to the chip and what is the chip's form factor (e.g. soic8)? The datasheet mentions SOP/WSON/PDIP. > I want read it out and reflash a new BIOS file. > > Therefore I really need help how to connect the chip pins with the buspirate > pins in a correct way. > > This is how pins are shown in the data sheet of Macronix MX25L1605DM2I-12G > > CS# 1 8 VCC > SO/SIO1 2 7 HOLD# > WP#ACC 3 6 SCLK > GND 4 5 SI/SIO0 http://dangerousprototypes.com/docs/Bus_Pirate_I/O_Pin_Descriptions This is how I connect my buspirate to a MX25L1605A soic8 chip: CS# (CS) [1 8] VCC (bridge with buspirate pin 3+7) SO (MISO) [2 7] HOLD # (+3V3) WP# (bridge with buspirate pin 7+8) [3 6] SCLK (CLK) GND (GND) [4 5] SI (MOSI) > > I am using Bus Pirate v3.5 with FW v6.2-beta1 r1981 BL v4.4 and flashrom > v0.9.6.1-r1624 on Windows. HiZ>i Bus Pirate v3.a Firmware v6.2-beta1 r1981 Bootloader v4.4 > > Would I have to setup the buspirate in a terminal before using flashrom? I > mean SPI mode and so on? If yes could someone help me with this settings > too? It's not necessary to change modes (no need to change from HiZ to SPI). > > Thanks! > > Best regards, > Daniel > > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > http://www.flashrom.org/mailman/listinfo/flashrom

1 0

MX25L1605DM2I-12G with Buspirate
by Daniel . 29 Nov '12

29 Nov '12

Hi everyone, I am absolute beginner but I need to read and write the above mentioned serial Flash memory. This is a BIOS chip and had a bad flash. Now it is unsoldered from mainboard. I want read it out and reflash a new BIOS file. Therefore I really need help how to connect the chip pins with the buspirate pins in a correct way. This is how pins are shown in the data sheet of Macronix MX25L1605DM2I-12G CS# 1 8 VCC SO/SIO1 2 7 HOLD# WP#ACC 3 6 SCLK GND 4 5 SI/SIO0 I am using Bus Pirate v3.5 with FW v6.2-beta1 r1981 BL v4.4 and flashrom v0.9.6.1-r1624 on Windows. Would I have to setup the buspirate in a terminal before using flashrom? I mean SPI mode and so on? If yes could someone help me with this settings too? Thanks! Best regards, Daniel

1 0

GA-M720-US3 (rev. 1.1) flashrom -V
by UnbAs.Foro 28 Nov '12

28 Nov '12

Hi! Thanks for your sotfware. I upload my results of -V and my -w Thanks!!

1 0

Supermicro X9DRW
by lesovsky 27 Nov '12

27 Nov '12

# flashrom -VV -p internal -r backup.bin flashrom v0.9.6-r1559 on Linux 3.4.9-gentoo-h64-tesla-a (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with unknown PCI library, GCC 4.5.4, big endian Command line (5 args): flashrom -VV -p internal -r backup.bin Calibrating delay loop... OS timer resolution is 1 usecs, 1997M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10004 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Supermicro" DMI string system-product-name: "X9DRW" DMI string system-version: "0123456789" DMI string baseboard-manufacturer: "Supermicro" DMI string baseboard-product-name: "X9DRW" DMI string baseboard-version: "0123456789" DMI string chassis-type: "Desktop" Found chipset "Intel X79" with PCI ID 8086:1d41. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x8 Root Complex Register Block address = 0xfed1c000 GCS = 0xc20: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0xd8, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x90, read w/ addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x9f, read w/o addr, none op[7]: 0xc7, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00020000 (FADDR) 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x000f0000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x0000ffff) is read-only. 0x58: 0x0fff0400 FREG1: BIOS region (0x00400000-0x00ffffff) is read-write. 0x5C: 0x03ff0020 FREG2: WARNING: Management Engine region (0x00020000-0x003fffff) is locked. 0x60: 0x00000fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x001f0010 FREG4: Platform Data region (0x00010000-0x0001ffff) is read-write. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00002005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040003 FLMAP1 0x12100206 FLMAP2 0x00210020 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 0 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x24900025 FLILL 0x00000000 --- Details --- Component 1 density: 16 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 50 MHz Write and Erase Clock Freq.: 50 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz No forbidden opcodes. === Region Section === FLREG0 0x000f0000 FLREG1 0x0fff0400 FLREG2 0x03ff0020 FLREG3 0x00000fff FLREG4 0x001f0010 --- Details --- Region 0 (Descr.) 0x00000000 - 0x0000ffff Region 1 (BIOS ) 0x00400000 - 0x00ffffff Region 2 (ME ) 0x00020000 - 0x003fffff Region 3 (GbE ) is unused. Region 4 (Platf.) 0x00010000 - 0x0001ffff === Master Section === FLMSTR1 0x1a1b0000 FLMSTR2 0x04050000 FLMSTR3 0x08090118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw rw ME r rw GbE r rw SPI Read Configuration: prefetching enabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25LF040A, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0xff, id2 0xff Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Unknown SFDP-capable chip, 0 kB: program_opcodes: preop=5006 optype=462b opmenu=055a0302c79f0190 on-the-fly OPCODE (0x5A) re-programmed, op-pos=2 SFDP revision = 1.0 SFDP number of parameter headers is 1 (NPH = 0). SFDP parameter table header 0/0: ID 0x00, version 1.0 Length 36 B, Parameter Table Pointer 0x000030 Parsing JEDEC flash parameter table... 3-Byte only addressing. Status register is non-volatile and the standard does not allow vendors to tell us whether EWSR/WREN is needed for status register writes - assuming EWSR. Write chunk size is at least 64 B. Flash chip size is 16384 kB. Block eraser 0: 4096 x 4096 B with opcode 0x20 Tried to add a duplicate block eraser: 4096 x 4096 B with opcode 0x20. Block eraser 1: 256 x 65536 B with opcode 0xd8 done. === SFDP has autodetected a flash chip which is not natively supported by flashrom yet. All standard operations (read, verify, erase and write) should work, but to support all possible features we need to add them manually. You can help us by mailing us the output of the following command to flashrom(a)flashrom.org: 'flashrom -VV [plus the -p/--programmer parameter (if needed)]' Thanks for your help! === Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI) at physical address 0x0. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xff, id2 0xff Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Unknown flash chip "SFDP-capable chip" (16384 kB, SPI). Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x020000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0x7f96b19158a0 Restoring MMIO space at 0x7f96b191589c Restoring MMIO space at 0x7f96b1915898 Restoring MMIO space at 0x7f96b1915896 Restoring MMIO space at 0x7f96b1915894 Restoring PCI config space for 00:1f:0 reg 0xdc -- С уважением Алексей В. Лесовский отдел разработки ПО, ИД Абак-Пресс

2 3

[PATCH 3/3] Fix sp_openserport users on Windows.
by Stefan Tauner 26 Nov '12

26 Nov '12

Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- buspirate_spi.c | 2 +- pony_spi.c | 2 +- serprog.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/buspirate_spi.c b/buspirate_spi.c index 92d7fb4..55d4133 100644 --- a/buspirate_spi.c +++ b/buspirate_spi.c @@ -40,7 +40,7 @@ static int buspirate_serialport_setup(char *dev) { /* 115200bps, 8 databits, no parity, 1 stopbit */ sp_fd = sp_openserport(dev, 115200); - if (sp_fd < 0) + if (sp_fd == SER_INV_FD) return 1; return 0; } diff --git a/pony_spi.c b/pony_spi.c index 7875200..101751f 100644 --- a/pony_spi.c +++ b/pony_spi.c @@ -116,7 +116,7 @@ int pony_spi_init(void) arg = extract_programmer_param("dev"); if (arg && strlen(arg)) { sp_fd = sp_openserport(arg, 9600); - if (sp_fd < 0) { + if (sp_fd == SER_INV_FD) { free(arg); return 1; } diff --git a/serprog.c b/serprog.c index edc5a7b..98c839e 100644 --- a/serprog.c +++ b/serprog.c @@ -372,7 +372,7 @@ int serprog_init(void) } if (strlen(device)) { sp_fd = sp_openserport(device, atoi(baudport)); - if (sp_fd < 0) { + if (sp_fd == SER_INV_FD) { free(device); return 1; } -- Kind regards, Stefan Tauner

1 0

[PATCH 2/3] Break endless loop in serialport_write().
by Stefan Tauner 26 Nov '12

26 Nov '12

serialport_write could loop endlessly when used with a seemingly valid port that does always return 0 on writes instead of an error. Give up after 10k tries. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- serial.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/serial.c b/serial.c index 11a749c..a3cdefb 100644 --- a/serial.c +++ b/serial.c @@ -264,6 +264,7 @@ int serialport_write(unsigned char *buf, unsigned int writecnt) #else ssize_t tmp = 0; #endif + uint empty_writes = 10000; while (writecnt > 0) { #ifdef _WIN32 @@ -275,9 +276,15 @@ int serialport_write(unsigned char *buf, unsigned int writecnt) msg_perr("Serial port write error!\n"); return 1; } - if (!tmp) + if (!tmp) { msg_pdbg("Empty write\n"); - writecnt -= tmp; + empty_writes--; + if (empty_writes == 0) { + msg_perr("Serial port seems dead!\n"); + return 1; + } + } + writecnt -= tmp; buf += tmp; } -- Kind regards, Stefan Tauner

1 0

[PATCH 1/3] Fix error message in sp_openserport().
by Stefan Tauner 26 Nov '12

26 Nov '12

free seems to touch errno on windows...? Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- serial.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/serial.c b/serial.c index 7e47dcc..11a749c 100644 --- a/serial.c +++ b/serial.c @@ -109,6 +109,7 @@ fdtype sp_openserport(char *dev, unsigned int baud) #ifdef _WIN32 HANDLE fd; char *dev2 = dev; + int err; if ((strlen(dev) > 3) && (tolower((unsigned char)dev[0]) == 'c') && (tolower((unsigned char)dev[1]) == 'o') && (tolower((unsigned char)dev[2]) == 'm')) { @@ -122,10 +123,11 @@ fdtype sp_openserport(char *dev, unsigned int baud) } fd = CreateFile(dev2, GENERIC_READ | GENERIC_WRITE, 0, NULL, OPEN_EXISTING, 0, NULL); + err = errno; // free may change errno if (dev2 != dev) free(dev2); if (fd == INVALID_HANDLE_VALUE) { - msg_perr("Error: cannot open serial port: %s\n", strerror(errno)); + msg_perr("Error: cannot open serial port: %s\n", strerror(err)); return SER_INV_FD; } DCB dcb; -- Kind regards, Stefan Tauner

1 0

[PATCH 0/3] serial woes
by Stefan Tauner 26 Nov '12

26 Nov '12

Idwer noticed a few problems... these patches try to fix them. Idwer please try one at the time and report if they work as intended: the first one should fix the "no error" message, the second one should stop the loop after 10k tries, the third one should fix the underlying problem for good. Stefan Tauner (3): Fix error message in sp_openserport(). Break endless loop in serialport_write(). Fix sp_openserport users on Windows. buspirate_spi.c | 2 +- pony_spi.c | 2 +- serial.c | 15 ++++++++++++--- serprog.c | 2 +- 4 files changed, 15 insertions(+), 6 deletions(-) -- Kind regards, Stefan Tauner

1 0

W836xx: Vico : flashrom -V
by Siniša R. 25 Nov '12

25 Nov '12

flashrom v0.9.6.1-r1563 on Linux 3.5.0-19-generic (i686) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 2 usecs, 1728M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 998 us, 10000 myus = 14494 us, 8 myus = 9 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Acer, inc." DMI string system-product-name: "TravelMate 6231 " DMI string system-version: "Not Applicable" DMI string baseboard-manufacturer: "Acer, Inc." DMI string baseboard-product-name: "Vico " DMI string baseboard-version: "Not Applicable" DMI string chassis-type: "Other" DMI chassis-type is not specific enough. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: fc. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. ======================================================================== WARNING! You may be running flashrom on an unsupported laptop. We could not detect this for sure because your vendor has not setup the SMBIOS tables correctly. You can enforce execution by adding '-p internal:laptop=this_is_not_a_laptop' to the command line, but please read the following warning if you are not sure. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. Error: Programmer initialization failed.

1 0

flashrom -V
by nicolas gras 24 Nov '12

24 Nov '12

flashrom v0.9.5.2-r1517 on Linux 3.2.0-24-generic (x86_64), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 869M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10072 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2N-MX SE Plus" DMI string baseboard-version: "Rev x.xx" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Flash bus type is SPI SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 SPI control is 0x0002, req=0, gnt=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L8005" (1024 kB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x13 Found Macronix flash chip "MX25L8005" (1024 kB, SPI). No operations were specified.

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom