- flashrom - mail.coreboot.org

PROBLEM, was stupid and tested "flashrom -EV", cant flash now.
by Magnus Alm 12 Apr '10

12 Apr '10

Argh! sudo flashrom -f -c SST39SF040 -w BACKUP2.rom flashrom v0.9.1-r993 on Linux 2.6.32-19-generic (i686), built with libpci 3.0.0, GCC 4.4.3 No coreboot table found. ======================================================================== WARNING! You seem to be running flashrom on a laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. ======================================================================== Found chipset "VIA VT8235", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Disabling flash write protection for board "Acer Ferrari 3400"... OK. Calibrating delay loop... OK. No EEPROM/flash device found. But a forced read works: sudo flashrom -f -r -c SST39SF040 crap.rom flashrom v0.9.1-r993 on Linux 2.6.32-19-generic (i686), built with libpci 3.0.0, GCC 4.4.3 No coreboot table found. ======================================================================== WARNING! You seem to be running flashrom on a laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. ======================================================================== Found chipset "VIA VT8235", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Disabling flash write protection for board "Acer Ferrari 3400"... OK. Calibrating delay loop... OK. No EEPROM/flash device found. Force read (-f -r -c) requested, forcing chip probe success: Found chip "SST SST39SF040" (512 KB, Parallel) at physical address 0xfff80000. Please note that forced reads most likely contain garbage. Reading flash... done. I need a function added to flashrom so I can specify chip and address to write to. /Magnus

2 1

Re: [flashrom] [PATCH] Board enable (EC sleep) for Acer Ferrari 3400
by Magnus Alm 12 Apr '10

12 Apr '10

HI! "sudo flashrom" doesn't cause any problems now. "sudo flashrom -r BACKUP.ROM" works also tho the created file is smaller than the downloaded file. -rw-r--r-- 1 root root 524288 2010-04-12 00:36 BACKUP.ROM -rw-r--r-- 1 magnus magnus 525894 2004-10-19 09:32 ZI5_3C23.WPH That might not be so strange if the downloaded file also contains information about "magic bits". /Magnus 2010/4/12 Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de>: > BE WARNED: FLASHROM COMES WITH NO WARRANTY! THIS IS ESPECIALLY TRUE FOR > LAPTOPS, AND ESPECIALLY ESPECIALLY TRUE FOR LAPTOPS WITH SHARED EC. > Nevertheless, I think that trying to *read* flash contents with this patch > is not more unsafe than reading without this patch. Be warned that a crashed > EC might mean no fan control. Don't even *THINK* about erase/write until > read works fine! > > This is the first system with EC sleep support in flashrom, and the first > user of the register_shutdown infrastructure. > > PCI match uses one out of many chips with subsystem ID Acer:0x0057, and > also the northbridge (with bogus subsystem ID). DMI match added just for > safety, as fiddling with the KBC is dangerous. > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > --- > board_enable.c | 100 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++ > 1 files changed, 100 insertions(+), 0 deletions(-) > > diff --git a/board_enable.c b/board_enable.c > index f1f7953..ce82131 100644 > --- a/board_enable.c > +++ b/board_enable.c > @@ -29,6 +29,66 @@ > #include "flash.h" > > /* > + * Functions for EC/KBC communication > + * port = 0x60 for KBC, port = 0x62 (typically) for EC > + */ > +static int wait_uc_writebuf_empty(uint16_t port) > +{ > + int count; > + for (count = 0; count < 50; count++) > + { > + /* quit if OBF bit clear */ > + if (!(INB(port + 4) & 2)) > + return 0; > + usleep(10000); > + } > + return -1; > +} > + > +static int wait_uc_readbuf_full(uint16_t port) > +{ > + int count; > + for (count = 0; count < 50; count++) > + { > + /* quit if IBF bit set */ > + if (INB(port + 4) & 1) > + return 0; > + usleep(10000); > + } > + return -1; > +} > + > +static int uc_send_command(uint16_t port, uint8_t command) > +{ > + if (wait_uc_writebuf_empty(port) != 0) > + return -1; > + OUTB(command, port + 4); > + return 0; > +} > + > +#if 0 > +static int uc_send_data(uint16_t port, uint8_t command) > +{ > + if (wait_uc_writebuf_empty(port) != 0) > + return -1; > + OUTB(command, port); > + return 0; > +} > +#endif > + > +static int uc_read_data(uint16_t port) > +{ > + if (wait_uc_readbuf_full(port) != 0) > + return -1; > + return INB(port); > +} > + > +static void uc_flush_data(uint16_t port) > +{ > + INB(port); > +} > + > +/* > * Helper functions for many Winbond Super I/Os of the W836xx range. > */ > /* Enter extended functions */ > @@ -1307,6 +1367,45 @@ static int it8712f_gpio3_1_raise(const char *name) > return it8712f_gpio_set(32, 1); > } > > +static void send_kbc_command(void * cmdptr) > +{ > + uc_send_command(0x60, *(uint8_t*)cmdptr); > +} > + > +static int board_acer_ferrari3400(const char *name) > +{ > + static uint8_t enable_command = 0xAA; > + uint16_t pmio_base; > + struct pci_dev * dev; > + > + dev = pci_dev_find(0x1106, 0x3177); > + if (!dev) > + { > + fprintf(stderr, "ERROR: %s - Can't find VT8235\n", name); > + return -1; > + } > + pmio_base = pci_read_word(dev, 0x88) & 0xFF80; > + if (pmio_base == 0 || pmio_base == 0xFF80) > + { > + fprintf(stderr, "ERROR: %s - invalid PMIO base %04x\n", > + name, pmio_base); > + return -1; > + } > + > + usleep(100000); /* Give the user a fair chance to release enter > + before killing keyboard/mouse */ > + > + uc_flush_data(0x60); > + register_shutdown(send_kbc_command, &enable_command); > + if (INB(pmio_base + 4) & 1) > + uc_send_command(0x60, 0xE5); /* ACPI mode */ > + else > + uc_send_command(0x60, 0xD8); /* APM/legacy mode */ > + > + uc_read_data(0x60); /* wait for EC shutdown */ > + return 0; > +} > + > /** > * Below is the list of boards which need a special "board enable" code in > * flashrom before their ROM chip can be accessed/written to. > @@ -1356,6 +1455,7 @@ struct board_pciid_enable board_pciid_enables[] = { > {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, > {0x10de, 0x01e0, 0x147b, 0x1c00, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S", 0, OK, nvidia_mcp_gpio8_raise}, > {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, > + {0x1106, 0x3177, 0x1025, 0x0057, 0x1106, 0x3188, 0x1106, 0x3188, "^Ferrari 3400", NULL, NULL, "Acer", "Ferrari 3400", 0, OK, board_acer_ferrari3400}, > {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, > {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, > {0x1022, 0x746B, 0, 0, 0, 0, 0, 0, NULL, "AGAMI", "ARUMA", "agami", "Aruma", 0, OK, w83627hf_gpio24_raise_2e}, > -- > 1.7.0 > >

2 2

Re: [flashrom] [PATCH] Add board enable for ABit NF7-S
by Uwe Hermann 12 Apr '10

12 Apr '10

On Sun, Apr 11, 2010 at 02:26:58PM +0200, Michael Karcher wrote: > V2.0 has been killed from the strings. The V2.0 and V1.0 differences > are unknown. It's the same mainboard page, but different BIOS > downloads. Both BIOSses have the same board enable, though, so I don't > care if this also matches V1.0. If it does not match V1.0 and we > encounter that board, we just have to add another line. > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > Acked-by: Tom Brand <worntreads(a)sbcglobal.net> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Uwe. -- http://www.hermann-uwe.de | http://www.randomprojects.org http://www.crazy-hacks.org | http://www.unmaintained-free-software.org

2 1

[commit] r993 - trunk
by repository service 11 Apr '10

11 Apr '10

Author: mkarcher Date: Sun Apr 11 23:01:06 2010 New Revision: 993 URL: http://flashrom.org/trac/coreboot/changeset/993 Log: Add board enable for ABit NF7-S Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Tom Brand <worntreads(a)sbcglobal.net> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/board_enable.c trunk/print_wiki.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Fri Apr 9 02:02:38 2010 (r992) +++ trunk/board_enable.c Sun Apr 11 23:01:06 2010 (r993) @@ -578,6 +578,14 @@ } /** + * Suited for Abit NF7-S: NVIDIA CK804. + */ +static int nvidia_mcp_gpio8_raise(const char *name) +{ + return nvidia_mcp_gpio_set(0x08, 1); +} + +/** * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. */ static int nvidia_mcp_gpio10_raise(const char *name) @@ -1346,6 +1354,7 @@ {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, NULL, "Abit", "IP35", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x2930, 0x147b, 0x1083, 0x10ec, 0x8167, 0x147b, 0x1083, NULL, NULL, NULL, "Abit", "IP35 Pro", 0, OK, intel_ich_gpio16_raise}, {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, + {0x10de, 0x01e0, 0x147b, 0x1c00, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S", 0, OK, nvidia_mcp_gpio8_raise}, {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, Modified: trunk/print_wiki.c ============================================================================== --- trunk/print_wiki.c Fri Apr 9 02:02:38 2010 (r992) +++ trunk/print_wiki.c Sun Apr 11 23:01:06 2010 (r993) @@ -215,6 +215,7 @@ { "Abit", "VT6X4", "http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?fMTYPE=Sl…" }, { "Abit", "IP35", "http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?fMTYPE=LG…" }, { "Abit", "IP35 Pro", "http://www.abit.com.tw/page/de/motherboard/motherboard_detail.php?fMTYPE=LG…" }, + { "Abit", "NF7-S", "http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?fMTYPE=So…"}, { "Acorp", "6A815EPD", "http://web.archive.org/web/20021206163652/www.acorp.com.tw/English/default.…" }, { "agami", "Aruma", "http://web.archive.org/web/20080212111524/http://www.agami.com/site/ais-600…" }, { "Albatron", "PM266A Pro", "http://www.albatron.com.tw/English/Product/MB/pro_detail.asp?rlink=Overview…" }, /* FIXME */

1 0

Re: [flashrom] [PATCH] Add board enable for ABit NF7-S
by Benjamin BELLEC 11 Apr '10

11 Apr '10

As I can see here http://www.ocmodshop.com/default.aspx?a=144 differences between v1 and v2 are : /This motherboard is the NF7-S rev 2.0 which is the newest revision, revision 2.0 features the new crush 18D nvidia chipset which should allow for better overclocking a a few new features./ Le 11/04/2010 14:26, Michael Karcher a écrit : > V2.0 has been killed from the strings. The V2.0 and V1.0 differences > are unknown. It's the same mainboard page, but different BIOS > downloads. Both BIOSses have the same board enable, though, so I don't > care if this also matches V1.0. If it does not match V1.0 and we > encounter that board, we just have to add another line. >

1 0

Re: [flashrom] [PATCH] Add board enable for ABit NF7-S V2.0
by Uwe Hermann 11 Apr '10

11 Apr '10

On Thu, Apr 08, 2010 at 11:33:08PM +0200, Michael Karcher wrote: > This one should really work now, after fixing both the IDs and the > GPIO number. > Note to myself: Never ever do a board enable, as trivially as it might > look, when in a hurry! > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Assuming this is tested by someone or you are sure it works ok: Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> > + * Suited for ABit NF7-S V2.0: NVIDIA CK804. "Abit" for consistency, please. Though "abit" might actually be the more correct spelling as per vendor website, maybe we should change that. Also, is the "V2.0" really a different board (PCB) than the "NF7-S"? Finally, feel free to also add the board URL in the same commit. Uwe. -- http://www.hermann-uwe.de | http://www.randomprojects.org http://www.crazy-hacks.org | http://www.unmaintained-free-software.org

2 1

Epia EK
by oscar 11 Apr '10

11 Apr '10

Hello, I was told on the flashrom mailing list to send some info here since flashrom failed to program my EPIA-EK mainboard's BIOS. Please see the attached ZIP file. If you have any questions, just ask. I'll try to do my best to answer. oscar An attachment has been stripped: BIOS.zip

3 3

flashrom works on ASUS P2B-LS almost as is
by Keith Hui 11 Apr '10

11 Apr '10

Hi, I am sent from coreboot mailing list to help make flashrom fully working on my Asus P2B-LS board fully work. When I did mine, I just forced ASUS P2B-F as the target and it works. No modification to flashrom required. The flash chip on my board is SST 39SF020 and all operations work. Used this setup to flash coreboot several times while booted with coreboot. Good news is the board enable for P2B-LS would be identical to P2B-F meaning a lot less work. Cheers Keith

2 3

Re: [flashrom] [PATCH] Add board enable for ABit NF7-S V2.0
by fred 09 Apr '10

09 Apr '10

On Fri, 2010-04-09 at 17:46 +0200, Michael Karcher wrote: > This one should really work now, after fixing both the IDs and the > GPIO number. > Note to myself: Never ever do a board enable, as trivially as it might > look, when in a hurry! > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > --- > board_enable.c | 9 +++++++++ > 1 files changed, 9 insertions(+), 0 deletions(-) > > diff --git a/board_enable.c b/board_enable.c > index 9b05f76..2f75b78 100644 > --- a/board_enable.c > +++ b/board_enable.c > @@ -578,6 +578,14 @@ static int nvidia_mcp_gpio2_raise(const char *name) > } > > /** > + * Suited for ABit NF7-S V2.0: NVIDIA CK804. > + */ > +static int nvidia_mcp_gpio8_raise(const char *name) > +{ > + return nvidia_mcp_gpio_set(0x08, 1); > +} > + > +/** > * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. > */ > static int nvidia_mcp_gpio10_raise(const char *name) > @@ -1346,6 +1354,7 @@ struct board_pciid_enable board_pciid_enables[] = { > {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, NULL, "Abit", "IP35", 0, OK, intel_ich_gpio16_raise}, > {0x8086, 0x2930, 0x147b, 0x1083, 0x10ec, 0x8167, 0x147b, 0x1083, NULL, NULL, NULL, "Abit", "IP35 Pro", 0, OK, intel_ich_gpio16_raise}, > {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, > + {0x10de, 0x01e0, 0x147b, 0x1c00, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S V2.0", 0, OK, nvidia_mcp_gpio8_raise}, > {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, > {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, > {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, Acked-by: Tom Brand <worntreads(a)sbcglobal.net> The official bios update via Abit: http://file.abit.com.tw/pub/download/bios/nf7-s_2.0//nf7d27.exe The output of lspci and flashrom -V: http://www.coreboot.org/pipermail/flashrom/2010-April/002889.html Ans the superiotool -deV dump: superiotool r3844 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x84fe, id=0x1752 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0x0000, rev=0x0 Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0x0000, rev=0x0 Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0x0000, rev=0x0 Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x5217, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0x00, port+1=0x00 Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627HF/F/HG/G (id=0x52, rev=0x17) at 0x2e Register dump: idx 02 20 21 22 23 24 25 26 28 29 2a 2b 2c 2e 2f val ff 52 17 ff fe 84 00 00 00 00 7d c1 ff 00 ff def 00 52 NA ff 00 MM 00 00 00 00 7c c0 00 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 01 03 f0 06 02 0e 00 ff 00 00 def 01 03 f0 06 02 0e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 01 03 78 07 03 3b def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 01 02 f8 03 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 00 80 def 01 00 60 00 64 01 0c 80 LDN 0x06 (Consumer IR) idx 30 60 61 70 val 00 00 00 00 def 00 00 00 00 LDN 0x07 (Game port, MIDI port, GPIO 1) idx 30 60 61 62 63 70 f0 f1 f2 val 01 00 00 00 00 00 ff 00 00 def 00 02 01 03 30 09 ff 00 00 LDN 0x08 (GPIO 2, Watchdog timer) idx 30 f0 f1 f2 f3 f5 f6 f6 f7 val 01 ff 00 00 00 00 00 00 00 def 00 ff 00 00 00 00 00 00 00 LDN 0x09 (GPIO 3) idx 30 f0 f1 f2 f3 val 01 ff 00 00 40 def 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 f0 f1 f3 f4 f6 f7 f9 fe ff val 00 00 00 00 40 00 00 00 00 00 00 af 3f 00 00 00 01 00 00 def 00 00 00 00 NA NA 00 00 00 00 00 00 00 00 00 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 val 01 02 90 00 00 def 00 00 00 00 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff

1 0

r990 udelay fails for me ...
by Urja Rannikko 09 Apr '10

09 Apr '10

Hi... first: [root@phenom trunk]# ./flashrom -V flashrom v0.9.1-r990 on Linux 2.6.32-ARCH (x86_64), built with libpci 3.1.7, GCC 4.4.3 20100316 (prerelease) No coreboot table found. DMI string system-manufacturer: "System Manufacturer" DMI string system-product-name: "System Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "K8S-MX" DMI string baseboard-version: "Rev 1.xx" DMI string chassis-type: "Desktop" This chipset supports the following protocols: Non-SPI. WARNING: No chipset found. Flash detection will most likely fail. Calibrating delay loop... 424M loops per second, delay more than 1011355431720o short, recalculating... ... and it halts there... (actually it doesnt, look at the end of mail) This is the first cosmetic fix: Index: udelay.c =================================================================== --- udelay.c (revision 990) +++ udelay.c (working copy) @@ -93,7 +93,7 @@ */ for (i = 0; i < 4; i++) { if (measure_delay(100) < 90) { - msg_pdbg("delay more than 10% too short, " + msg_pdbg("delay more than 10%% too short, " "recalculating... "); goto recalibrate; } That doesnt help with the 100% CPU + "halt" (i dont know how long it would take...). I know that flashrom doesnt support K8S-MX (the internal driver anyways). I'm just back at work with serprog on this machine, so it seems funny to test the delay abilities of the host system even with -p serprog ... -- 21:15... uh so it isnt halted, just taking a long time (continuation to that log) " 370M loops per second, delay more than 1011355432146o short, recalculating...373M loops per second, delay more than 1011355432350o short, recalculating... " (I left it on while lookin at that % thing)... --- 21:20... <cont> "366M loops per second, delay more than 1011355432556o short, recalculating... 373M loops per second, delay more than 1011355432350o short, recalculating... " -- 21:23 <cont> " 367M loops per second, delay loop is unreliable, trying to continue 10 myus = 7 us, 100 myus = 69 us, 1000 myus = 687 us, 10000 myus = 11233 us, OK." Then it scans for flash chips on this thing and finds nothing, which is normal. Note that i'm running on x86_64 (if it works on 32-bit machines, i think that might have something to do with this, not sure.). Report complete, urjaman out

2 5

[commit] r992 - trunk
by repository service 09 Apr '10

09 Apr '10

Author: hailfinger Date: Fri Apr 9 02:02:38 2010 New Revision: 992 URL: http://flashrom.org/trac/coreboot/changeset/992 Log: Reinitialize the delay loop upon recalibration. Fix an unescaped % in a format specifier. Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/udelay.c Modified: trunk/udelay.c ============================================================================== --- trunk/udelay.c Sat Apr 3 12:27:08 2010 (r991) +++ trunk/udelay.c Fri Apr 9 02:02:38 2010 (r992) @@ -66,6 +66,7 @@ printf("Calibrating delay loop... "); recalibrate: + count = 1000; while (1) { timeusec = measure_delay(count); if (timeusec > 1000000 / 4) @@ -93,7 +94,7 @@ */ for (i = 0; i < 4; i++) { if (measure_delay(100) < 90) { - msg_pdbg("delay more than 10% too short, " + msg_pdbg("delay more than 10%% too short, " "recalculating... "); goto recalibrate; }

1 0

[PATCH] Add board enable for ABit NF7-S V2.0
by Michael Karcher 08 Apr '10

08 Apr '10

This one should really work now, after fixing both the IDs and the GPIO number. Note to myself: Never ever do a board enable, as trivially as it might look, when in a hurry! Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> --- board_enable.c | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 9b05f76..2f75b78 100644 --- a/board_enable.c +++ b/board_enable.c @@ -578,6 +578,14 @@ static int nvidia_mcp_gpio2_raise(const char *name) } /** + * Suited for ABit NF7-S V2.0: NVIDIA CK804. + */ +static int nvidia_mcp_gpio8_raise(const char *name) +{ + return nvidia_mcp_gpio_set(0x08, 1); +} + +/** * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. */ static int nvidia_mcp_gpio10_raise(const char *name) @@ -1346,6 +1354,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, NULL, "Abit", "IP35", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x2930, 0x147b, 0x1083, 0x10ec, 0x8167, 0x147b, 0x1083, NULL, NULL, NULL, "Abit", "IP35 Pro", 0, OK, intel_ich_gpio16_raise}, {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, + {0x10de, 0x01e0, 0x147b, 0x1c00, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S V2.0", 0, OK, nvidia_mcp_gpio8_raise}, {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, -- 1.7.0

1 0

chipset support output f. flashrom -V
by ataya65＠googlemail.com 08 Apr '10

08 Apr '10

flashrom -V flashrom -V flashrom v0.9.1-r931 No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: "ASRock" DMI string baseboard-product-name: "K10N78" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP78S", enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Guessed flash bus type is SPI Found SMBus device 10de:0752 at 00:01:1 SPI BAR is at 0xf8e80000, after clearing low bits BAR is at 0xf8e80000 Mapping MCP67 SPI at 0xf8e80000, unaligned size 0x544. SPI control is 0xc04a, enable=0, idle=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org to help us finish support for your chipset. Thanks. SPI on this chipset is not supported yet. OK. This chipset supports the following protocols: None. Calibrating delay loop... 702M loops per second, 100 myus = 199 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F004S5, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Intel 82802AC, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Macronix MX25L512, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for PMC Pm49FL004, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF003A/B, 384 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF004A/B, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF004C, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF008A, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF008C, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF016C, 2048 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF020, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW040B, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW080A, 1024 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW080B, 1024 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FW002, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW016, 2048 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW040, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW080, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50LPW116, 2048 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W49F002U, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080FA, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. No EEPROM/flash device found. If you know which flash chip you have, and if this version of flashrom supports a similar flash chip, you can try to force read your chip. Run: flashrom -f -r -c similar_supported_flash_chip filename Note: flashrom can never write when the flash chip isn't found automatically. URL to the mainboard manf.: http://www.asrock.com/mb/overview.asp?Model=K10N78

2 1

Re: [flashrom] r990 udelay fails for me ...
by Urja Rannikko 08 Apr '10

08 Apr '10

I sent this accidentally only to carldani, sorry: On Thu, Apr 8, 2010 at 23:04, Urja Rannikko <urjaman(a)gmail.com> wrote: > > > On Wed, Apr 7, 2010 at 15:19, Carl-Daniel Hailfinger < > c-d.hailfinger.devel.2006(a)gmx.net> wrote: > >> On 03.04.2010 23:09, Carl-Daniel Hailfinger wrote: >> > On 03.04.2010 01:28, Urja Rannikko wrote: >> > >> >> This seems to "fix" this for me - the delay loop is still unreliable, >> but >> >> atleast the recalibration attempts only take 5s instead of minutes. >> This is >> >> a combined diff for both my fix and the % fix. >> >> >> >> Index: udelay.c >> >> =================================================================== >> >> --- udelay.c (revision 990) >> >> +++ udelay.c (working copy) >> >> @@ -66,6 +66,7 @@ >> >> printf("Calibrating delay loop... "); >> >> >> >> recalibrate: >> >> + count = 1000; >> >> while (1) { >> >> timeusec = measure_delay(count); >> >> if (timeusec > 1000000 / 4) >> >> >> >> >> > >> > Does the timing get more reliable if you try the following stuff: >> > >> > - change the comparison above to >> > >> > if (timeusec > 1000) >> > >> >> I expect this little change to improve precision dramatically. >> >> >> > - Make sure there are no CPU frequency changes or sleep states >> > >> > >> >> Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> >> >> >> > >> > In general, I like your patch. I just hope to get more input if reducing >> > the abort condition in the loop from 250 ms to 1 ms helps as well. >> > >> >> We need your patch, I had just hoped that improved precision would be >> possible with the additional change I suggested. Anyway, this is >> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> >> >> Can you commit? >> >> If I would have commit access ;) > > I'm sorry that i forgot about this until now (real life+work had priority) > - I just changed my mb from the failing (in many ways) Asus K8S-MX to a > M4N78-AM. > > For this MB the delay loop is accurate with if (timeusec > 1000000 / 4). > Just for reference - M4N78-AM: > "timeusec < 1000" - 3 runs: > Calibrating delay loop... 1156M loops per second, 10 myus = 10 us, 100 myus > = 101 us, 1000 myus = 1148 us, 10000 myus = 10998 us, OK. > Calibrating delay loop... 1156M loops per second, 10 myus = 10 us, 100 myus > = 101 us, 1000 myus = 1092 us, 10000 myus = 13070 us, OK. > Calibrating delay loop... 1146M loops per second, 10 myus = 10 us, 100 myus > = 181 us, 1000 myus = 996 us, 10000 myus = 10807 us, OK. > > "timeusec > 1000000 / 4" - 3 runs: > Calibrating delay loop... 1153M loops per second, 10 myus = 10 us, 100 myus > = 100 us, 1000 myus = 998 us, 10000 myus = 10003 us, OK. > Calibrating delay loop... 1154M loops per second, 10 myus = 10 us, 100 myus > = 100 us, 1000 myus = 1004 us, 10000 myus = 10014 us, OK. > Calibrating delay loop... 1132M loops per second, 10 myus = 10 us, 100 myus > = 98 us, 1000 myus = 987 us, 10000 myus = 10442 us, OK. > > I dont (atleast Right Now - i dont know what I will do with that K8S-MX) > want to take my new shiny system apart just to put that MB from '05 back for > running flashrom a few times on it, sorry. > -- urjaman

1 0

[PATCH] Add board enable for ABit NF7-S V2.0
by Michael Karcher 08 Apr '10

08 Apr '10

Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> --- board_enable.c | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 9b05f76..7de9f13 100644 --- a/board_enable.c +++ b/board_enable.c @@ -578,6 +578,14 @@ static int nvidia_mcp_gpio2_raise(const char *name) } /** + * Suited for ABit NF7-S V2.0: NVIDIA CK804. + */ +static int nvidia_mcp_gpio5_raise(const char *name) +{ + return nvidia_mcp_gpio_set(0x05, 1); +} + +/** * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. */ static int nvidia_mcp_gpio10_raise(const char *name) @@ -1346,6 +1354,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, NULL, "Abit", "IP35", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x2930, 0x147b, 0x1083, 0x10ec, 0x8167, 0x147b, 0x1083, NULL, NULL, NULL, "Abit", "IP35 Pro", 0, OK, intel_ich_gpio16_raise}, {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, + {0x10de, 0x01e0, 0x147b, 0x1c00, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S V2.0", 0, OK, nvidia_mcp_gpio5_raise}, {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, -- 1.7.0

1 0

[PATCH] Add board enable for ABit NF7-S V2.0
by Michael Karcher 08 Apr '10

08 Apr '10

Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> $ sudo flashrom -EV flashrom v0.9.1-r706 No coreboot table found. Found chipset "NVIDIA NForce2", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 605M loops per second, 100 myus = 162 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMD Am29F002(N)BB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for AMD Am29F002(N)BT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for AMD Am29F080B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for AMD Am29LV081B, 1024 KB: probe_29f040b: id1 0xff, id2 0xff Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT29C010A, 128 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT49F002(N), 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Atmel AT49F002(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for AMIC A25L40P, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xda, id2 0x3d Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xda, id2 0x3d Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for AMIC A49LF040A, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for EMST F49B002UA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for EON EN29F002(A)(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Fujitsu MBM29F004BC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Fujitsu MBM29F004TC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 28F001BX-B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Intel 28F001BX-T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: probe_29f002: id1 0xda, id2 0x3d Probing for Macronix MX29F001T, 128 KB: probe_29f002: id1 0xda, id2 0x3d Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xda, id2 0x3d Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xda, id2 0x3d Probing for Macronix MX29LV040, 512 KB: probe_29f002: id1 0xda, id2 0x3d Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F0002T, 256 KB: probe_29f040b: id1 0xd0, id2 0xab Probing for PMC Pm29F0002B, 256 KB: probe_29f040b: id1 0xd0, id2 0xab Probing for PMC Pm39LV010, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for PMC Pm49FL002, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for PMC Pm49FL004, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0xff, id2 0xff Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST29EE020A, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST39VF080, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF003A/B, 384 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF004A/B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for ST M29F002T/NT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for ST M29W040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0xda, id2 0x3d Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0xda, id2 0x3d Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xd0, id2 0xab Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS S29C31004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SyncMOS S29C51001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SyncMOS S29C51002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for SyncMOS S29C51004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for TI TMS29F002RB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for TI TMS29F002RT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0xda, id2 0x3d Found chip "Winbond W39V040A" (512 KB, LPC) at physical address 0xfff80000. Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0xda, id2 0x3d Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W49V002FA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xda, id2 0x3d Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: id1 0xff, id2 0xff Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: id1 0xda, id2 0x3d Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Erasing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x466a1 ERASE FAILED! FAILED! ERROR at 0x00000000: Expected=0xff, Read=0x49 Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net channel #flashrom or mail flashrom(a)flashrom.org ------------------------------------------------------------ DO NOT REBOOT OR POWEROFF! $ sudo lspci -vvvxxxnn 00:00.0 Host bridge [0600]: nVidia Corporation nForce2 IGP2 [10de:01e0] (rev c1) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M] Capabilities: [40] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Capabilities: [60] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit Revision ID: 0.16 Kernel driver in use: agpgart-nvidia Kernel modules: nvidia-agp 00: de 10 e0 01 06 00 b0 00 c1 00 00 06 00 00 80 00 10: 08 00 00 d8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 40: 02 60 30 00 1b 42 00 1f 02 03 00 00 ff ff ff ff 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 60: 08 00 01 20 20 00 88 80 10 00 00 00 01 ff 01 9f 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 80: 0e 01 00 00 ff ff ff 3f 01 00 00 00 01 80 00 00 90: 14 80 40 a7 14 80 40 a5 00 30 00 00 00 00 00 00 a0: 40 00 00 00 2f fb 10 00 01 00 00 00 00 00 00 00 b0: cc ff 07 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 33 33 03 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: d6 01 47 00 16 30 00 10 00 00 00 00 00 00 00 00 f0: 0f 00 00 38 00 00 00 00 00 00 00 00 00 00 00 00 00:00.1 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 1 [10de:01eb] (rev c1) Subsystem: nVidia Corporation Device [10de:0c17] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 eb 01 00 00 20 00 c1 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 17 0c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 04 00 00 70 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 11 04 42 81 01 00 00 00 01 00 00 00 01 00 00 00 70: 08 24 00 00 08 24 00 00 2c 07 00 01 40 07 00 01 80: 01 00 00 00 f3 13 0f 03 08 05 08 05 78 c8 a6 3f 90: 09 0a 33 33 30 22 43 22 00 11 54 01 0d 22 77 07 a0: 2a 00 00 00 00 00 10 00 2a 00 00 00 00 00 10 00 b0: 2a 00 00 00 00 00 10 00 2a 00 00 00 01 00 10 00 c0: 00 31 22 02 00 00 00 00 00 00 00 00 ff ff 02 00 d0: 44 4e 00 00 22 22 00 00 0d 00 00 00 1e 00 00 00 e0: 1a 00 00 00 80 00 00 00 88 44 44 10 b1 04 30 40 f0: 10 18 1e 03 04 10 04 3f 09 44 1c 04 01 03 70 30 00:00.2 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 4 [10de:01ee] (rev c1) Subsystem: nVidia Corporation Device [10de:0c17] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 ee 01 00 00 20 00 c1 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 17 0c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 01 20 da 12 01 20 db 02 00 00 00 02 01 00 37 1f 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: ff ff bf 05 ff 3f ff 05 ff bf ff 07 ff ef 5f 07 80: ff ff fe 07 ff ff af 06 ff ff 7f 04 ff cf ff 03 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 ef 01 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 d0: 11 00 00 00 04 00 00 00 00 00 00 d8 ff ff ff db e0: 01 00 a3 2f 01 00 a3 2f 01 00 a3 2f 01 00 a3 2f f0: 01 00 a3 2f 01 00 a3 2f 01 00 a3 2f 01 00 a3 2f 00:00.3 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 3 [10de:01ed] (rev c1) Subsystem: nVidia Corporation Device [10de:0c17] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 ed 01 00 00 20 00 c1 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 17 0c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 30 00 00 00 00 90 00 00 63 00 00 00 71 07 00 00 50: 76 06 00 00 72 95 00 00 68 ea 00 00 50 40 20 00 60: e9 00 00 00 00 06 f7 67 ff ea 77 88 88 87 00 77 70: 01 80 e0 01 6a 00 00 00 03 10 01 20 44 00 02 01 80: ff ff 00 00 ff ff ff ff 00 00 00 00 00 00 00 00 90: ff 10 ff 10 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: ff 30 00 00 ff 30 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 04 40 00 00 ff ff ff ff f0: 1c 40 00 00 ff ff ff ff ff ff ff ff ff ff ff ff 00:00.4 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 2 [10de:01ec] (rev c1) Subsystem: nVidia Corporation Device [10de:0c17] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 ec 01 00 00 20 00 c1 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 17 0c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: aa 33 aa 33 aa 55 aa 55 aa 11 aa 11 aa 33 aa 33 70: ff 99 ff 99 f0 00 00 00 7f 3e c0 0f aa 55 aa 11 80: ff 99 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 5d 5d 5d 5d 5c 5b 5b 5a 18 18 18 18 18 18 18 17 a0: 00 00 00 00 09 95 00 00 00 00 00 00 5f 05 a0 00 b0: 78 56 34 12 ef cd ab 89 9b 4a 66 22 ee bd dc 8b c0: 66 06 55 05 00 00 00 00 00 20 22 00 00 00 00 00 d0: ff 20 ff 20 ff 20 ff 7f 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.5 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 5 [10de:01ef] (rev c1) Subsystem: nVidia Corporation Device [10de:0c17] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 ef 01 00 00 20 00 c1 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 17 0c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 00 00 00 00 00 00 00 00 fa 20 f7 07 fa 20 f7 07 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 ff ff ff 3f 00 00 00 00 ff ff ff 3f c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:01.0 ISA bridge [0601]: nVidia Corporation nForce2 ISA Bridge [10de:0060] (rev a4) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [48] HyperTransport: Slave or Primary Interface Command: BaseUnitID=1 UnitCnt=15 MastHost- DefDir- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO- <CRCErr=0 Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO+ <CRCErr=0 Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit Revision ID: 0.00 00: de 10 60 00 0f 00 b0 00 a4 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 48 00 00 00 00 00 00 00 00 00 00 00 40: 7b 14 00 1c de fd 3c 08 08 00 e1 01 60 00 88 88 50: a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 40 00 00 01 44 00 00 01 42 00 00 00 01 f8 ff 70: 10 00 ff ff 03 00 00 00 0f 00 40 00 00 d2 00 00 80: 09 20 0d 00 8d 02 08 00 3f 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: cc 00 02 00 0a 00 00 00 00 00 00 00 00 00 00 00 e0: 00 11 00 07 2f 00 00 00 00 20 06 80 00 00 00 00 f0: 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:01.1 SMBus [0c05]: nVidia Corporation nForce2 SMBus (MCP) [10de:0064] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at c400 [size=32] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00: de 10 64 00 01 00 b0 00 a2 00 05 0c 00 00 80 00 10: 01 c4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01 40: 7b 14 00 1c 01 00 02 c0 00 00 00 00 00 00 00 00 50: 01 50 00 00 01 51 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.0 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at e0080000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: de 10 67 00 07 00 b0 00 a4 10 03 0c 00 00 80 00 10: 00 00 08 e0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 03 01 40: 7b 14 00 1c 01 00 02 fe 00 00 00 00 02 00 00 00 50: 11 00 00 00 1d 47 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.1 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 20 Region 0: Memory at e0083000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: de 10 67 00 07 00 b0 00 a4 10 03 0c 00 00 80 00 10: 00 30 08 e0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 02 03 01 40: 7b 14 00 1c 01 00 02 fe 00 00 00 00 03 00 00 00 50: 00 00 00 00 1d 47 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.2 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0068] (rev a4) (prog-if 20) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 22 Region 0: Memory at e0086000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0080 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: de 10 68 00 06 00 b0 00 a4 20 03 0c 00 00 80 00 10: 00 60 08 e0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0c 03 03 01 40: 7b 14 00 1c 0a 80 80 20 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 01 00 00 60 98 81 c3 03 00 00 00 00 00 00 70: 00 00 00 05 00 10 20 80 89 3d 84 22 e7 25 54 80 80: 01 00 02 fe 00 00 00 00 00 00 00 00 15 16 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 00 00 00 08 e0 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:04.0 Ethernet controller [0200]: nVidia Corporation nForce2 Ethernet Controller [10de:0066] (rev a1) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 22 Region 0: Memory at e0087000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at b000 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=0 PME- Kernel driver in use: forcedeth Kernel modules: forcedeth 00: de 10 66 00 07 00 b0 00 a1 00 00 02 00 00 00 00 10: 00 70 08 e0 01 b0 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 01 14 40: 7b 14 00 1c 01 00 02 fe 00 01 00 00 04 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:05.0 Multimedia audio controller [0401]: nVidia Corporation nForce Audio Processing Unit [10de:006b] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 3000ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=512K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: de 10 6b 00 06 00 b0 00 a2 00 01 04 00 00 00 00 10: 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 01 0c 40: 7b 14 00 1c 01 00 02 06 00 00 00 00 0a 05 00 00 50: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 60: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 70: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 80: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 90: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 a0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 b0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 c0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 d0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 e0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 f0: 01 00 02 06 01 00 02 06 01 00 02 06 01 00 02 06 00:06.0 Multimedia audio controller [0401]: nVidia Corporation nForce2 AC97 Audio Controler (MCP) [10de:006a] (rev a1) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at b400 [size=256] Region 1: I/O ports at b800 [size=128] Region 2: Memory at e0081000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: Intel ICH Kernel modules: snd-intel8x0 00: de 10 6a 00 07 00 b0 00 a1 00 01 04 00 00 00 00 10: 01 b4 00 00 01 b8 00 00 00 10 08 e0 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 02 05 40: 7b 14 00 1c 01 00 02 06 00 00 00 00 06 01 00 01 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:08.0 PCI bridge [0604]: nVidia Corporation nForce2 External PCI Bridge [10de:006c] (rev a3) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00009000-0000afff Memory behind bridge: de000000-dfffffff Prefetchable memory behind bridge: 40000000-400fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: de 10 6c 00 07 01 a0 00 a3 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 20 90 a0 80 22 20: 00 de f0 df 00 40 00 40 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 02 40: 00 00 00 00 01 00 02 00 01 00 00 00 08 0b 07 00 50: 0c 0d fe 3f 0e 0f 00 00 7f 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:09.0 IDE interface [0101]: nVidia Corporation nForce2 IDE [10de:0065] (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_amd 00: de 10 65 00 05 00 b0 00 a2 8a 01 01 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 f0 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01 40: 7b 14 00 1c 01 00 02 00 00 00 00 00 00 09 00 00 50: 03 f0 00 00 00 00 00 00 99 20 22 20 12 00 20 22 60: 00 c5 00 c7 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 10 8b 2c 00 00 02 0c 00 80 00 02 90: 00 00 02 10 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0d.0 FireWire (IEEE 1394) [0c00]: nVidia Corporation nForce2 FireWire (IEEE 1394) Controller [10de:006e] (rev a3) (prog-if 10) Subsystem: ABIT Computer Corp. Device [147b:1c00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at e0084000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e0085000 (32-bit, non-prefetchable) [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ohci1394 Kernel modules: firewire-ohci, ohci1394 00: de 10 6e 00 07 00 b0 00 a3 10 00 0c 00 00 00 00 10: 00 40 08 e0 00 50 08 e0 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01 40: 00 00 00 00 01 00 02 fe 00 80 00 00 13 14 00 01 50: 7b 14 00 1c 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:1e.0 PCI bridge [0604]: nVidia Corporation nForce2 AGP [10de:01e8] (rev c1) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dc000000-ddffffff Prefetchable memory behind bridge: d0000000-d7ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: de 10 e8 01 07 01 20 02 c1 00 04 06 00 20 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 f0 00 20 22 20: 00 dc f0 dd 00 d0 f0 d7 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 00 40: 01 00 00 00 00 00 f0 3f 20 00 00 00 ff ff ff ff 50: 00 00 00 d8 00 f0 ff db ff ff ff ff ff ff ff ff 60: ff 40 ff 40 00 00 00 20 00 00 00 00 ff ff ff ff 70: ff ff ff ff 00 00 00 00 00 00 00 00 ff ff ff ff 80: ff ff ff ff 00 80 01 00 4c 01 00 00 ff ff ff ff 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff a0: 1b 42 00 1f ff ff ff ff ff ff ff ff ff ff ff ff b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 01:0b.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller [1095:3112] (rev 02) Subsystem: Silicon Image, Inc. Device [1095:6112] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 9000 [size=8] Region 1: I/O ports at 9400 [size=4] Region 2: I/O ports at 9800 [size=8] Region 3: I/O ports at 9c00 [size=4] Region 4: I/O ports at a000 [size=16] Region 5: Memory at df000000 (32-bit, non-prefetchable) [size=512] [virtual] Expansion ROM at 40000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: sata_sil 00: 95 10 12 31 07 00 b0 02 02 00 04 01 08 20 00 00 10: 01 90 00 00 01 94 00 00 01 98 00 00 01 9c 00 00 20: 01 a0 00 00 00 00 00 df 00 00 00 00 95 10 12 61 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00 40: 02 00 00 00 5a 01 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 00 22 06 00 40 00 64 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 22 00 00 00 22 00 00 00 00 00 00 00 cc af 7f ff 90: 00 00 00 00 ff 00 00 00 00 00 00 18 00 00 00 00 a0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40 b0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40 c0: 84 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX 5200] [10de:0322] (rev a1) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 19 Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M] [virtual] Expansion ROM at dd000000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb 00: de 10 22 03 07 00 b0 02 a1 00 00 03 00 f8 00 00 10: 00 00 00 dc 08 00 00 d0 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0c 01 05 01 40: 00 00 00 00 02 00 30 00 1b 0e 00 1f 02 43 00 1f 50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00 60: 01 44 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 --- board_enable.c | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 9b05f76..212c212 100644 --- a/board_enable.c +++ b/board_enable.c @@ -578,6 +578,14 @@ static int nvidia_mcp_gpio2_raise(const char *name) } /** + * Suited for ABit NF7-S V2.0: NVIDIA CK804. + */ +static int nvidia_mcp_gpio5_raise(const char *name) +{ + return nvidia_mcp_gpio_set(0x05, 1); +} + +/** * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. */ static int nvidia_mcp_gpio10_raise(const char *name) @@ -1346,6 +1354,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, NULL, "Abit", "IP35", 0, OK, intel_ich_gpio16_raise}, {0x8086, 0x2930, 0x147b, 0x1083, 0x10ec, 0x8167, 0x147b, 0x1083, NULL, NULL, NULL, "Abit", "IP35 Pro", 0, OK, intel_ich_gpio16_raise}, {0x10de, 0x0050, 0x147b, 0x1c1a, 0, 0, 0, 0, NULL, NULL, NULL, "Abit", "KN8 Ultra", 0, NT, nvidia_mcp_gpio2_lower}, + {0x10de, 0x01e0, 0x147b, 0x0c17, 0x10de, 0x0060, 0x147B, 0x1c00, NULL, NULL, NULL, "Abit", "NF7-S V2.0", 0, OK, nvidia_mcp_gpio5_raise}, {0x1106, 0x0691, 0, 0, 0x1106, 0x3057, 0, 0, NULL, "abit", "vt6x4", "Abit", "VT6X4", 0, OK, via_apollo_gpo4_lower}, {0x105a, 0x0d30, 0x105a, 0x4d33, 0x8086, 0x1130, 0x8086, 0, NULL, NULL, NULL, "Acorp", "6A815EPD", 0, OK, board_acorp_6a815epd}, {0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise}, -- 1.7.0

1 0

ERASE (or write) not working on Fujitsu Lifebook P7120
by Mikko Strahlendorff 08 Apr '10

08 Apr '10

Doesn't seem to be fatal, but ERASE is not working, so also write operation is stopped. Here's the output of different runs of flashrom: -------- xxx:~$ sudo flashrom -V flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "FUJITSU SIEMENS" DMI string system-product-name: "LIFEBOOK P7120" DMI string system-version: " " DMI string baseboard-manufacturer: "FUJITSU" DMI string baseboard-product-name: "FJNB1A5" DMI string baseboard-version: "CP254699-01 " DMI string chassis-type: "Notebook" Laptop detected via DMI ======================================================================== WARNING! You seem to be running flashrom on a laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. ======================================================================== Found chipset "Intel ICH6-M", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 OK. This chipset supports the following protocols: FWH. Calibrating delay loop... 262M loops per second, 100 myus = 161 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Intel 28F004S5, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x16, id2 0x4e Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for Macronix MX25L512, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x16, id2 0x4e Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5a Found chip "SST SST49LF008A" (1024 KB, FWH) at physical address 0xfff00000. Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Lock status for 0x080000 (size 0x010000) is 00, full access Lock status for 0x090000 (size 0x010000) is 00, full access Lock status for 0x0a0000 (size 0x010000) is 00, full access Lock status for 0x0b0000 (size 0x010000) is 00, full access Lock status for 0x0c0000 (size 0x010000) is 00, full access Lock status for 0x0d0000 (size 0x010000) is 00, full access Lock status for 0x0e0000 (size 0x010000) is 00, full access Lock status for 0x0f0000 (size 0x010000) is 00, full access Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x16, id2 0x4e Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x16, id2 0x4e Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xe8, id2 0x40 Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x16, id2 0x4e Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x00, id2 0x00 Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for Winbond W49F002U, 256 KB: skipped. Host bus type FWH and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5a Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5a Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5a Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type FWH and chip bus type SPI are incompatible. === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === ---------- The start of flashrom -rV xx.rom is the same, but end is as follows: ... === Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Lock status for 0x080000 (size 0x010000) is 00, full access Lock status for 0x090000 (size 0x010000) is 00, full access Lock status for 0x0a0000 (size 0x010000) is 00, full access Lock status for 0x0b0000 (size 0x010000) is 00, full access Lock status for 0x0c0000 (size 0x010000) is 00, full access Lock status for 0x0d0000 (size 0x010000) is 00, full access Lock status for 0x0e0000 (size 0x010000) is 00, full access Lock status for 0x0f0000 (size 0x010000) is 00, full access Reading flash... done. and produces same file as was earlier uploaded. ------------ flashrom -wV fails: ... === Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Lock status for 0x080000 (size 0x010000) is 00, full access Lock status for 0x090000 (size 0x010000) is 00, full access Lock status for 0x0a0000 (size 0x010000) is 00, full access Lock status for 0x0b0000 (size 0x010000) is 00, full access Lock status for 0x0c0000 (size 0x010000) is 00, full access Lock status for 0x0d0000 (size 0x010000) is 00, full access Lock status for 0x0e0000 (size 0x010000) is 00, full access Lock status for 0x0f0000 (size 0x010000) is 00, full access Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x00000fff: 0x30 ERASE FAILED! Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x0000ffff: 0x389 ERASE FAILED! Looking at blockwise erase function 2... eraseblock layout is known, but no matching block erase function found. Looking for another erase function. Looking at blockwise erase function 3... not defined. Looking for another erase function. Looking at blockwise erase function 4... not defined. Looking for another erase function. FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! -------- pretty much the same with -EV: .... === Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Lock status for 0x080000 (size 0x010000) is 00, full access Lock status for 0x090000 (size 0x010000) is 00, full access Lock status for 0x0a0000 (size 0x010000) is 00, full access Lock status for 0x0b0000 (size 0x010000) is 00, full access Lock status for 0x0c0000 (size 0x010000) is 00, full access Lock status for 0x0d0000 (size 0x010000) is 00, full access Lock status for 0x0e0000 (size 0x010000) is 00, full access Lock status for 0x0f0000 (size 0x010000) is 00, full access Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x00000fff: 0x30 ERASE FAILED! Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x0000ffff: 0x389 ERASE FAILED! Looking at blockwise erase function 2... eraseblock layout is known, but no matching block erase function found. Looking for another erase function. Looking at blockwise erase function 3... not defined. Looking for another erase function. Looking at blockwise erase function 4... not defined. Looking for another erase function. FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! It seems no worries though for rebooting, cause the flashrom -r produces the same rom as before. I hope this helps for developing flashrom! Cheers, Mikko -- _______________ Mikko Strahlendorff |* | | o | | strahlen(a)mikko.net | -- \ _ | | \ |

2 2

Re: [flashrom] JIDA CMOS
by Bill Flanders (wtflanders) 08 Apr '10

08 Apr '10

Marc, I'm in the same boat using Kontron boards and Linux. The flashrom program works to load the BIOS but I need a Linux solution to load custom CMOS/BIOS settings. I currently have the DOS version of JIDACMOS and have contacted Kontron for the Linux version but have not heard back yet. Did you settle on nvramtool or the Linux version of JIDACMOS ? thanks, Bill

4 7

summary for XW9400 (Tyan OEM S2915-E)
by Nils-Helge Garli Hegvik 07 Apr '10

07 Apr '10

Hi! Summary for the XW9400 debug session we just recently had on freenode. Don't hesitate to contact me again if you need any more information. Regards, Nils-Helge Garli Hegvik

1 1

Re: [flashrom] flashing results for the MS-7094 board
by Jelle 06 Apr '10

06 Apr '10

Hi Carl-Daniel, Sorry for the late reply, but here are the dumps from both 'lspci -nnvvxxx' and 'superiotool -d -e -V' (see attachments). Regards, Jelle 2009/10/5 <c-d.hailfinger.devel.2006(a)gmx.net>: > Hi Jelle, > > I'm sorry I didn't see your mail earlier. Luc will investigate the issue > you reported. > > On 26.08.2009 22:37, Jelle Geerts wrote: > > > I've ran flashrom -v {-E,-r,-v,-w} on my MS-7094 board. > > > For more info regarding the board, please see > > > http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&p… > > > > > > I've attached the results to this e-mail. Reading/verifying/writing > > > worked fine. Erasing however, didn't go so well, as you can see in the > > > attached log. > > > > Current flashrom (0.9.1 or later) is a lot more paranoid and it would > have detected that the write only succeeded because it didn't change the > parts which could not be erased. > > > > > BTW, two thumbs up to the flashrom developers: the Award flash utility > > > did not work (kept saying 'Unknown flash type'), but flashrom did. ;) > > > > Thanks! Such feedback keeps us going. > > > > > Found chipset "VIA VT8237", enabling flash write... OK. > > > Found board "MSI K8T Neo2", enabling flash write... OK. > > > > In theory, that board enable routine should have covered the GPIOs needed. > However, flashrom detects your board as "K8T Neo2" although it is a "K8T > Neo2-F V2.0", so that may explain what you're seeing. > The big problem is that these boards often have identical PCI IDs, so > differentiating between them is almost impossible. > > Could you please mail the output of "lspci -nnvvxxx" to the list? Maybe > we find some way to differentiate betweent your board and the K8T Neo2. > > Regards, > Carl-Daniel > > -- http://www.hailfinger.org/

1 0

Supported programmers compatibility report - my Silicon Image SiI 3124 PCI-X SATA Ctrl 1095:3124 is OK
by Mick Reed 05 Apr '10

05 Apr '10

I can report that I am able to read, write, and erase with a PCI-X Sata SIL3124 card. I see on the wiki that it shows a question mark. Note that I had to place it temporarily in a 5v PCI slot to get it to write. Seems the particular flash chip on my card is a 5v part. Silicon Image SiI 3124 PCI-X SATA Ctrl 1095:3124 OK Thanks to all for the incredible flashrom tool, my SATA controller wouldn't be working without it! DISCLAIMER I know it's a wiki. However, this page says not to edit it directly, as (some) of the content is autogenerated from "flashrom -z output." I'm not a developer, and don't know how to patch any possible existing code to cause an autogenerated update of this info. This is just a report, and I hope this helps. Thanks. -Mick

1 0

motherboard application
by adiblol 04 Apr '10

04 Apr '10

Outputs of 'flashrom -V', 'lspci -nnvvvxxx', 'superiotool -deV' + photo of PC label (contains information about model): http://j.imagehost.org/download/0919/flashrom_tar (tar.gz) Official BIOS DL: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=359… (other drivers available here: http://support.ts.fujitsu.com/Download/ShowFiles.asp?strFTS=Treiber?LNG=COM… ) Happy reverse engineering! ------- adiblol

1 0

[PATCH] Hack for Gateway m275
by Michael Karcher 04 Apr '10

04 Apr '10

Might help - this is how the native code does it. --- jedec.c | 32 ++++++++++++++++++++++++++------ 1 files changed, 26 insertions(+), 6 deletions(-) diff --git a/jedec.c b/jedec.c index 30c343f..aa32714 100644 --- a/jedec.c +++ b/jedec.c @@ -50,7 +50,14 @@ void toggle_ready_jedec_common(chipaddr dst, int delay) programmer_delay(delay); tmp2 = chip_readb(dst) & 0x40; if (tmp1 == tmp2) { - break; + /* Recheck to avoid spurious results. */ + programmer_delay(delay); + tmp1 = chip_readb(dst) & 0x40; + if (tmp1 == tmp2) + break; + msg_cdbg("Spurious toggle ready!\n"); + /* Avoid a false positive during next loop. */ + tmp2 = tmp1; } tmp1 = tmp2; } @@ -300,14 +307,16 @@ int write_byte_program_jedec_common(struct flashchip *flash, uint8_t *src, } retry: + chip_readb(bios); /* Issue JEDEC Byte Program command */ start_program_jedec_common(flash, mask); /* transfer data from source to destination */ chip_writeb(*src, dst); - toggle_ready_jedec(bios); + toggle_ready_jedec(dst); if (chip_readb(dst) != *src && tried++ < MAX_REFLASH_TRIES) { + msg_cerr("Retrying the write at 0x%lx\n", dst); goto retry; } @@ -364,7 +373,7 @@ retry: failed = verify_range(flash, src, start, page_size, NULL); if (failed && tried++ < MAX_REFLASH_TRIES) { - msg_cerr("retrying.\n"); + msg_cerr("Retrying the write at 0x%lx\n", dst); goto retry; } if (failed) { @@ -430,20 +439,31 @@ int write_jedec_1(struct flashchip *flash, uint8_t * buf) mask = getaddrmask(flash); programmer_delay(10); +#if 0 if (erase_flash(flash)) { msg_cerr("ERASE FAILED!\n"); return -1; } +#else + msg_cinfo("Not erasing!\n"); +#endif + msg_cinfo("Checking if the to-be-written range is already erased\n"); + if (check_erased_range(flash, 128 * 1024, 320 * 1024)) { + msg_cerr("Range 0x20000-0x6ffff is not in erased state!\n"); + return -1; + } - msg_cinfo("Programming page: "); - for (i = 0; i < flash->total_size; i++) { + msg_cinfo("Programming 1k sized pages, starting at 128k, ending at 448k: "); + for (i = 128; i < flash->total_size - 64; i++) { if ((i & 0x3) == 0) - msg_cinfo("address: 0x%08lx", (unsigned long)i * 1024); + msg_cinfo("address: 0x%08lx,", (unsigned long)i * 1024); write_sector_jedec_common(flash, buf + i * 1024, dst + i * 1024, 1024, mask); +#if 0 if ((i & 0x3) == 0) msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b"); +#endif } msg_cinfo("DONE!\n"); -- 1.7.0

1 0

inneed help
by Nate Howell-Burke 04 Apr '10

04 Apr '10

I am on a friends laptop. I cant get internet at my house. I have my laptop with me. Can you send me the link to the irc site again so I can get with you guys again and hopefully fix my bios issue

1 0

bios issue
by admin1 03 Apr '10

03 Apr '10

I just flashed my Gateway m275 Tablet running ubuntu 9.10 with the 480401.bin bios from gateway and I have now been directed to e-mail you the failure report. Can you pleas help me? ifying flash... VERIFY FAILED at 0x00005002! Expected=0x7f, Read=0x3f, failed byte count from 0x00000000-0x0007ffff: 0x4fa18 Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net channel #flashrom or mail flashrom(a)flashrom.org

2 3

Re: [flashrom] [PATCH, v2] Intel 28F004/28F400 support
by Carl-Daniel Hailfinger 03 Apr '10

03 Apr '10

On 01.04.2010 20:12, Michael Karcher wrote: > Remove blockwise write for i82802ab chips. It will be reintroduced > in post-0.9.2 in a generic way. This is needed to fix > FWH-like chips with non-uniform sectors. > > These are: > Intel 28F001 > Sharp LHF00L04 > ST M50FW002 > ST M50LPW116 > > Add IDs for Intel 28F004/28F400 > I have modified the changelog a bit. > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > With the comments below addressed, this is Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> > 82802ab.c | 54 +++++++++------------------- > flash.h | 2 +- > flashchips.c | 110 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ > flashchips.h | 4 ++ > 4 files changed, 133 insertions(+), 37 deletions(-) > create mode 100755 dmidecode > > diff --git a/82802ab.c b/82802ab.c > index aa7e45e..0d1bd1a 100644 > --- a/82802ab.c > +++ b/82802ab.c > @@ -48,6 +48,7 @@ int probe_82802ab(struct flashchip *flash) > chipaddr bios = flash->virtual_memory; > uint8_t id1, id2; > uint8_t flashcontent1, flashcontent2; > + int shifted = (flash->feature_bits & FEATURE_ADDR_SHIFTED) != 0; > Can we rely on the compiler to set shifted=1 if the feature bit is set? We assign a boolean value to int shifted, and AFAIK the compiler is free to use pretty much any value here as long as that value gives reliable results (could be 0x2, could be 0xffffffff). What about the following code instead? + int shifted = (flash->feature_bits & FEATURE_ADDR_SHIFTED) ? 1 : 0; > > /* Reset to get a clean state */ > chip_writeb(0xFF, bios); > @@ -178,44 +179,25 @@ void write_page_82802ab(chipaddr bios, uint8_t *src, > int write_82802ab(struct flashchip *flash, uint8_t *buf) > { > int i; > - int total_size = flash->total_size * 1024; > - int page_size = flash->page_size; > chipaddr bios = flash->virtual_memory; > - uint8_t *tmpbuf = malloc(page_size); > > - if (!tmpbuf) { > - msg_cerr("Could not allocate memory!\n"); > - exit(1); > + if (erase_flash(flash)) { > + msg_cerr("ERASE FAILED!\n"); > + return -1; > } > - msg_cinfo("Programming page: \n"); > - for (i = 0; i < total_size / page_size; i++) { > [...] > + msg_cinfo("Programming page: "); > + for (i = 0; i < flash->total_size; i++) { > You change the write chunk size from page_size to 1024. Does "programming page" still make sense, or should it be "programming chunk at"? > diff --git a/dmidecode b/dmidecode > new file mode 100755 > index 0000000..e69de29 > Uhhh. Please make sure you don't commit dmidecode by accident. > diff --git a/flashchips.c b/flashchips.c > index 2dbc1e0..a9b6551 100644 > --- a/flashchips.c > +++ b/flashchips.c > @@ -2385,6 +2385,116 @@ struct flashchip flashchips[] = { > + { > + .vendor = "Intel", > + .name = "28F400BV/CV/CE-B", > + .bustype = CHIP_BUSTYPE_PARALLEL, > + .manufacture_id = INTEL_ID, > + .model_id = P28F400BB, > + }, > + > + { > + .vendor = "Intel", > + .name = "28F400BV/CV/CE-B", > Should be ...CE-T unless I'm mistaken. > + .bustype = CHIP_BUSTYPE_PARALLEL, > + .manufacture_id = INTEL_ID, > + .model_id = P28F400BT, > A compile test and run test with -p dummy (which triggers the automatic chipdefinition selftest) would be appreciated before committing just to make sure I didn't overlook anything problematic. Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

[commit] r991 - trunk
by repository service 03 Apr '10

03 Apr '10

Author: mkarcher Date: Sat Apr 3 12:27:08 2010 New Revision: 991 URL: http://flashrom.org/trac/coreboot/changeset/991 Log: Intel 28F004/28F400 support Remove blockwise write for i82802ab chips. It will be reintroduced in post-0.9.2 in a generic way. This is needed to fix FWH-like chips with non-uniform sectors. These are: Intel 28F001 Sharp LHF00L04 ST M50FW002 ST M50LPW116 Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/82802ab.c trunk/flash.h trunk/flashchips.c trunk/flashchips.h Modified: trunk/82802ab.c ============================================================================== --- trunk/82802ab.c Thu Apr 1 01:55:06 2010 (r990) +++ trunk/82802ab.c Sat Apr 3 12:27:08 2010 (r991) @@ -48,6 +48,7 @@ chipaddr bios = flash->virtual_memory; uint8_t id1, id2; uint8_t flashcontent1, flashcontent2; + int shifted = (flash->feature_bits & FEATURE_ADDR_SHIFTED) != 0; /* Reset to get a clean state */ chip_writeb(0xFF, bios); @@ -57,8 +58,8 @@ chip_writeb(0x90, bios); programmer_delay(10); - id1 = chip_readb(bios); - id2 = chip_readb(bios + 0x01); + id1 = chip_readb(bios + (0x00 << shifted)); + id2 = chip_readb(bios + (0x01 << shifted)); /* Leave ID mode */ chip_writeb(0xFF, bios); @@ -71,8 +72,8 @@ msg_cdbg(", id1 parity violation"); /* Read the product ID location again. We should now see normal flash contents. */ - flashcontent1 = chip_readb(bios); - flashcontent2 = chip_readb(bios + 0x01); + flashcontent1 = chip_readb(bios + (0x00 << shifted)); + flashcontent2 = chip_readb(bios + (0x01 << shifted)); if (id1 == flashcontent1) msg_cdbg(", id1 is normal flash content"); @@ -178,44 +179,25 @@ int write_82802ab(struct flashchip *flash, uint8_t *buf) { int i; - int total_size = flash->total_size * 1024; - int page_size = flash->page_size; chipaddr bios = flash->virtual_memory; - uint8_t *tmpbuf = malloc(page_size); - if (!tmpbuf) { - msg_cerr("Could not allocate memory!\n"); - exit(1); - } - msg_cinfo("Programming page: \n"); - for (i = 0; i < total_size / page_size; i++) { - msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b"); - msg_cinfo("%04d at address: 0x%08x", i, i * page_size); - - /* Auto Skip Blocks, which already contain the desired data - * Faster, because we only write, what has changed - * More secure, because blocks, which are excluded - * (with the exclude or layout feature) - * or not erased and rewritten; their data is retained also in - * sudden power off situations - */ - chip_readn(tmpbuf, bios + i * page_size, page_size); - if (!memcmp((void *)(buf + i * page_size), tmpbuf, page_size)) { - msg_cdbg("SKIPPED\n"); - continue; - } + if (erase_flash(flash)) { + msg_cerr("ERASE FAILED!\n"); + return -1; + } - /* erase block by block and write block by block; this is the most secure way */ - if (erase_block_82802ab(flash, i * page_size, page_size)) { - msg_cerr("ERASE FAILED!\n"); - return -1; - } - write_page_82802ab(bios, buf + i * page_size, - bios + i * page_size, page_size); + msg_cinfo("Programming at: "); + for (i = 0; i < flash->total_size; i++) { + if ((i & 0x3) == 0) + msg_cinfo("address: 0x%08lx", (unsigned long)i * 1024); + + write_page_82802ab(bios, buf + i * 1024, bios + i * 1024, 1024); + + if ((i & 0x3) == 0) + msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b"); } - msg_cinfo("DONE!\n"); - free(tmpbuf); + msg_cinfo("DONE!\n"); return 0; } Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Thu Apr 1 01:55:06 2010 (r990) +++ trunk/flash.h Sat Apr 3 12:27:08 2010 (r991) @@ -166,7 +166,7 @@ #define FEATURE_ADDR_MASK (3 << 2) #define FEATURE_ADDR_2AA (1 << 2) #define FEATURE_ADDR_AAA (2 << 2) -#define FEATURE_ADDR_SHIFTED 0 +#define FEATURE_ADDR_SHIFTED (1 << 5) struct flashchip { const char *vendor; Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Thu Apr 1 01:55:06 2010 (r990) +++ trunk/flashchips.c Sat Apr 3 12:27:08 2010 (r991) @@ -2385,6 +2385,116 @@ { .vendor = "Intel", + .name = "28F004BV/BE-B", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F004BB, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .tested = TEST_UNTESTED, + .probe = probe_82802ab, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {16 * 1024, 1}, + {8 * 1024, 2}, + {96 * 1024, 1}, + {128 * 1024, 3}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F004BV/BE-T", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F004BT, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .tested = TEST_UNTESTED, + .probe = probe_82802ab, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {128 * 1024, 3}, + {96 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F400BV/CV/CE-B", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F400BB, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .feature_bits = FEATURE_ADDR_SHIFTED, + .tested = TEST_UNTESTED, + .probe = probe_82802ab, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {16 * 1024, 1}, + {8 * 1024, 2}, + {96 * 1024, 1}, + {128 * 1024, 3}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F400BV/CV/CE-T", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F400BT, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .feature_bits = FEATURE_ADDR_SHIFTED, + .tested = TEST_UNTESTED, + .probe = probe_82802ab, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {128 * 1024, 3}, + {96 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", .name = "82802AB", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = INTEL_ID, Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Thu Apr 1 01:55:06 2010 (r990) +++ trunk/flashchips.h Sat Apr 3 12:27:08 2010 (r991) @@ -259,6 +259,10 @@ #define E_28F016S5 0xAA #define P28F001BXT 0x94 /* 28F001BX-T */ #define P28F001BXB 0x95 /* 28F001BX-B */ +#define P28F004BT 0x78 /* 28F004BV/BE-T */ +#define P28F004BB 0x79 /* 28F004BV/BE-B */ +#define P28F400BT 0x70 /* 28F400BV/CV/CE-T */ +#define P28F400BB 0x71 /* 28F400BV/CV/CE-B */ #define SHARP_LH28F008SA 0xA2 /* Sharp chip, Intel Vendor ID */ #define SHARP_LH28F008SC 0xA6 /* Sharp chip, Intel Vendor ID */

1 0

[PATCH, v2, compilable] Board enable for IP530
by Michael Karcher 03 Apr '10

03 Apr '10

Now also leaves conf mode and selects the right logical device number. Autodetection fixed by putting the chip with (bogus) subdevice first. --- board_enable.c | 43 +++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 43 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 26c4d09..d1c09a7 100644 --- a/board_enable.c +++ b/board_enable.c @@ -96,6 +96,48 @@ static int enable_flash_decode_superio(void) #endif /** + * SMSC FDC37B787: Raise GPIO50 + */ + +static int fdc37b787_gpio50_raise(uint16_t port, const char * name) +{ + uint8_t id, val; + + OUTB(0x55, port); /* enter conf mode */ + id = sio_read(port, 0x20); + if (id != 0x44) { + fprintf(stderr, "\nERROR: %s: FDC37B787: Wrong ID 0x%02X.\n", + name, id); + OUTB(0xAA, port); /* leave conf mode */ + return -1; + } + + sio_write(port, 0x07, 0x08); /* Select Aux I/O subdevice */ + + val = sio_read(port, 0xC8); /* GP50 */ + if ((val & 0x1B) != 0x10) /* output, no invert, GPIO */ + { + fprintf(stderr, "\nERROR: %s: GPIO50 mode 0x%02X unexpected.\n", + name, val); + OUTB(0xAA, port); + return -1; + } + + sio_mask(port, 0xF9, 0x01, 0x01); + + OUTB(0xAA, port); /* Leave conf mode */ + return 0; +} + +/** + * Suited for Nokia IP530: Intel 440BX + PIIX4 + FDC37B787 + */ +static int fdc37b787_gpio50_raise_3f0(const char *name) +{ + return fdc37b787_gpio50_raise(0x3f0, name); +} + +/** * Winbond W83627HF: Raise GPIO24. * * Suited for: @@ -1398,6 +1440,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x10DE, 0x005E, 0x1462, 0x7135, 0x10DE, 0x0050, 0x1462, 0x7135, NULL, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", 0, OK, w83627thf_gpio4_4_raise_4e}, {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, {0x10DE, 0x005E, 0x1462, 0x7125, 0x10DE, 0x0052, 0x1462, 0x7125, NULL, NULL, NULL, "MSI", "K8N Neo4-F", 0, OK, nvidia_mcp_gpio2_raise}, + {0x1011, 0x0019, 0xaa55, 0xaa55, 0x8086, 0x7190, 0, 0, NULL, NULL, NULL, "Nokia", "IP530", 0, OK, fdc37b787_gpio50_raise_3f0}, {0x1106, 0x3099, 0, 0, 0x1106, 0x3074, 0, 0, NULL, "shuttle", "ak31", "Shuttle", "AK31", 0, OK, w836xx_memw_enable_2e}, {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, it8705f_write_enable_2e}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, NULL, "Shuttle", "FN25", 0, OK, board_shuttle_fn25}, -- 1.7.0

1 0

[PATCH, really v2] Board enable for IP530
by Michael Karcher 03 Apr '10

03 Apr '10

Now also leaves conf mode and selects the right logical device number. Autodetection fixed by putting the chip with (bogus) subdevice first. --- board_enable.c | 43 +++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 43 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 26c4d09..c434fc4 100644 --- a/board_enable.c +++ b/board_enable.c @@ -96,6 +96,48 @@ static int enable_flash_decode_superio(void) #endif /** + * SMSC FDC37B787: Raise GPIO50 + */ + +static int fdc37b787_gpio50_raise(uint16_t port, const char * name) +{ + uint8_t id, val; + + OUTB(0x55, port); /* enter conf mode */ + id = sio_read(port, 0x20); + if (id != 0x44) { + fprintf(stderr, "\nERROR: %s: FDC37B787: Wrong ID 0x%02X.\n", + name, id); + OUTB(0xAA, port); /* leave conf mode */ + return -1; + } + + sio_write(0x07, 0x08); /* Select Aux I/O subdevice */ + + val = sio_read(port, 0xC8); /* GP50 */ + if ((val & 0x1B) != 0x10) /* output, no invert, GPIO */ + { + fprintf(stderr, "\nERROR: %s: GPIO50 mode 0x%02X unexpected.\n", + name, val); + OUTB(0xAA, port); + return -1; + } + + sio_mask(port, 0xF9, 0x01, 0x01); + + OUTB(0xAA, port); /* Leave conf mode */ + return 0; +} + +/** + * Suited for Nokia IP530: Intel 440BX + PIIX4 + FDC37B787 + */ +static int fdc37b787_gpio50_raise_3f0(const char *name) +{ + return fdc37b787_gpio50_raise(0x3f0, name); +} + +/** * Winbond W83627HF: Raise GPIO24. * * Suited for: @@ -1398,6 +1440,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x10DE, 0x005E, 0x1462, 0x7135, 0x10DE, 0x0050, 0x1462, 0x7135, NULL, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", 0, OK, w83627thf_gpio4_4_raise_4e}, {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, {0x10DE, 0x005E, 0x1462, 0x7125, 0x10DE, 0x0052, 0x1462, 0x7125, NULL, NULL, NULL, "MSI", "K8N Neo4-F", 0, OK, nvidia_mcp_gpio2_raise}, + {0x1011, 0x0019, 0xaa55, 0xaa55, 0x8086, 0x7190, 0, 0, NULL, NULL, NULL, "Nokia", "IP530", 0, OK, fdc37b787_gpio50_raise_3f0}, {0x1106, 0x3099, 0, 0, 0x1106, 0x3074, 0, 0, NULL, "shuttle", "ak31", "Shuttle", "AK31", 0, OK, w836xx_memw_enable_2e}, {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, it8705f_write_enable_2e}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, NULL, "Shuttle", "FN25", 0, OK, board_shuttle_fn25}, -- 1.7.0

1 0

[PATCH, v2] Board enable for IP530
by Michael Karcher 03 Apr '10

03 Apr '10

Now also leaves conf mode and selects the right logical device number. --- board_enable.c | 40 ++++++++++++++++++++++++++++++++++++++++ 1 files changed, 40 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 26c4d09..f88b084 100644 --- a/board_enable.c +++ b/board_enable.c @@ -96,6 +96,45 @@ static int enable_flash_decode_superio(void) #endif /** + * SMSC FDC37B787: Raise GPIO50 + */ + +static int fdc37b787_gpio50_raise(uint16_t port, const char * name) +{ + uint8_t id, val; + + OUTB(0x55, port); /* enter conf mode */ + id = sio_read(port, 0x20); + if (id != 0x44) { + fprintf(stderr, "\nERROR: %s: FDC37B787: Wrong ID 0x%02X.\n", + name, id); + OUTB(0xAA, port); /* leave conf mode */ + return -1; + } + + val = sio_read(port, 0xC8); /* GP50 */ + if ((val & 0x1B) != 0x10) /* output, no invert, GPIO */ + { + fprintf(stderr, "\nERROR: %s: GPIO50 mode 0x%02X unexpected.\n", + name, val); + OUTB(0xAA, port); + return -1; + } + + sio_mask(port, 0xF9, 0x01, 0x01); + return 0; +} + +/** + * + * Suited for Nokia IP530: Intel 440BX + PIIX4 + FDC37B787 + */ +static int fdc37b787_gpio50_raise_3f0(const char *name) +{ + return fdc37b787_gpio50_raise(0x3f0, name); +} + +/** * Winbond W83627HF: Raise GPIO24. * * Suited for: @@ -1398,6 +1437,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x10DE, 0x005E, 0x1462, 0x7135, 0x10DE, 0x0050, 0x1462, 0x7135, NULL, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", 0, OK, w83627thf_gpio4_4_raise_4e}, {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, {0x10DE, 0x005E, 0x1462, 0x7125, 0x10DE, 0x0052, 0x1462, 0x7125, NULL, NULL, NULL, "MSI", "K8N Neo4-F", 0, OK, nvidia_mcp_gpio2_raise}, + {0x8086, 0x7190, 0, 0, 0x1011, 0x0019, 0xaa55, 0xaa55, NULL, NULL, NULL, "Nokia", "IP530", 0, OK, fdc37b787_gpio50_raise_3f0}, {0x1106, 0x3099, 0, 0, 0x1106, 0x3074, 0, 0, NULL, "shuttle", "ak31", "Shuttle", "AK31", 0, OK, w836xx_memw_enable_2e}, {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, it8705f_write_enable_2e}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, NULL, "Shuttle", "FN25", 0, OK, board_shuttle_fn25}, -- 1.7.0

1 0

flashrom on an Alpha Workstation 433au
by adrian.glaubitz＠googlemail.com 03 Apr '10

03 Apr '10

Hi, as the subject suggests I have run flashrom on a DEC Alpha Digital Personal Workstation [1], model 433au. flashrom itself segfaults but superiotool finds a SuperIO at least. Most DEC Alpha workstations are flashed using a proprietary flash utility which is run from the the SRM console [2]. There are several manuals on the net from DEC and Compaq which describe how to update the firmware using the original utilities, for example [3]. I have no idea so far how to enable/disable writing to the flash rom chips but I think it should not require any more magic than on x86 systems ;). Especially, because many of the Alpha systems are actually using Intel chipsets. Usually those Alpha machines have a jumper onboard which enables/disables flash write so there probably isn't the need for a specific board enable at all. Probably it's just a matter of finding the proper location of the address space of the flash chip in memory. I'm attaching the debug logs for superiotool -dV, lspci -nnvvvxxx and flashrom -V. Adrian [1] http://en.wikipedia.org/wiki/Digital_Personal_Workstation [2] http://www.compaq.com/alphaserver/download/srm_reference.pdf [3] ftp://15.200.2.21/ftp1/pub/alphaserver/firmware/retired_platforms/workstations/ASTN600/alpha500_600_V72_fw_relnote.pdf

2 1

[PATCH] Board enable for IP530
by Michael Karcher 03 Apr '10

03 Apr '10

Definitely post-0.9.2 --- board_enable.c | 40 ++++++++++++++++++++++++++++++++++++++++ 1 files changed, 40 insertions(+), 0 deletions(-) diff --git a/board_enable.c b/board_enable.c index 26c4d09..f88b084 100644 --- a/board_enable.c +++ b/board_enable.c @@ -96,6 +96,45 @@ static int enable_flash_decode_superio(void) #endif /** + * SMSC FDC37B787: Raise GPIO50 + */ + +static int fdc37b787_gpio50_raise(uint16_t port, const char * name) +{ + uint8_t id, val; + + OUTB(0x55, port); /* enter conf mode */ + id = sio_read(port, 0x20); + if (id != 0x44) { + fprintf(stderr, "\nERROR: %s: FDC37B787: Wrong ID 0x%02X.\n", + name, id); + OUTB(0xAA, port); /* leave conf mode */ + return -1; + } + + val = sio_read(port, 0xC8); /* GP50 */ + if ((val & 0x1B) != 0x10) /* output, no invert, GPIO */ + { + fprintf(stderr, "\nERROR: %s: GPIO50 mode 0x%02X unexpected.\n", + name, val); + OUTB(0xAA, port); + return -1; + } + + sio_mask(port, 0xF9, 0x01, 0x01); + return 0; +} + +/** + * Suited for Nokia IP530: Intel 440BX + PIIX4 + FDC37B787 + */ +static int fdc37b787_gpio50_raise_3f0(const char *name) +{ + return fdc37b787_gpio50_raise(0x3f0, name); +} + +/** * Winbond W83627HF: Raise GPIO24. * * Suited for: @@ -1398,6 +1437,7 @@ struct board_pciid_enable board_pciid_enables[] = { {0x10DE, 0x005E, 0x1462, 0x7135, 0x10DE, 0x0050, 0x1462, 0x7135, NULL, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", 0, OK, w83627thf_gpio4_4_raise_4e}, {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, {0x10DE, 0x005E, 0x1462, 0x7125, 0x10DE, 0x0052, 0x1462, 0x7125, NULL, NULL, NULL, "MSI", "K8N Neo4-F", 0, OK, nvidia_mcp_gpio2_raise}, + {0x8086, 0x7190, 0, 0, 0x1011, 0x0019, 0xaa55, 0xaa55, NULL, NULL, NULL, "Nokia", "IP530", 0, OK, fdc37b787_gpio50_raise_3f0}, {0x1106, 0x3099, 0, 0, 0x1106, 0x3074, 0, 0, NULL, "shuttle", "ak31", "Shuttle", "AK31", 0, OK, w836xx_memw_enable_2e}, {0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, NULL, "Shuttle", "AK38N", 256, OK, it8705f_write_enable_2e}, {0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, NULL, "Shuttle", "FN25", 0, OK, board_shuttle_fn25}, -- 1.7.0

1 0

NVIDIA MCP61
by Free Wind 02 Apr '10

02 Apr '10

flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "MSI" DMI string system-product-name: "MS-7309" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "MSI" DMI string baseboard-product-name: "MS-7309" DMI string baseboard-version: "1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61", enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Guessed flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 SPI BAR is at 0xfec80000, after clearing low bits BAR is at 0xfec80000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org to help us finish support for your chipset. Thanks. OK. This chipset supports the following protocols: LPC. Calibrating delay loop... 706M loops per second, 100 myus = 201 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Intel 28F004S5, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Intel 82802AC, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Macronix MX25L512, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x49, id2 0x2c, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF003A/B, 384 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF004A/B, 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF004C, 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF008A, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF008C, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF016C, 2048 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x49, id2 0x2c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x49, id2 0x2c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x0d, id2 0xfc Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x0d, id2 0xfc Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for ST M50FW016, 2048 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for ST M50FW040, 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for ST M50FW080, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x0d, id2 0xfc, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: skipped. Host bus type LPC and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x49, id2 0x2c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Winbond W39V080FA, 1024 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Host bus type LPC and chip bus type FWH are incompatible. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type LPC and chip bus type SPI are incompatible. No EEPROM/flash device found. If you know which flash chip you have, and if this version of flashrom supports a similar flash chip, you can try to force read your chip. Run: flashrom -f -r -c similar_supported_flash_chip filename Note: flashrom can never write when the flash chip isn't found automatically.

1 0

Re: [flashrom] [PATCH] Intel 28F004/28F400 support
by Carl-Daniel Hailfinger 01 Apr '10

01 Apr '10

On 01.04.2010 00:48, Michael Karcher wrote: > This should also fix broken write for non-uniform sectored FWH-like chips. > These are: > Intel 28F001 > Sharp LHF00L04 > ST M50FW002 > ST M50LPW116 > > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > --- > 82802ab.c | 85 +++++++++++++++++++++++++++++-------------- > chipdrivers.h | 3 ++ > flash.h | 2 +- > flashchips.c | 110 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ > flashchips.h | 4 ++ > 5 files changed, 175 insertions(+), 29 deletions(-) > > diff --git a/82802ab.c b/82802ab.c > index aa7e45e..27acaa3 100644 > --- a/82802ab.c > +++ b/82802ab.c > @@ -48,6 +48,12 @@ int probe_82802ab(struct flashchip *flash) > chipaddr bios = flash->virtual_memory; > uint8_t id1, id2; > uint8_t flashcontent1, flashcontent2; > + int id2_offset; > + > + if (flash->feature_bits & FEATURE_ADDR_SHIFTED) > Umm... I'm pretty sure that FEATURE_ADDR_SHIFTED has another meaning (the 0x555 etc shifted left by one bit). The id2_offset may be needed anyway, but I propose to use a variable "shifted" which is 0 for all non-shifted chips and 1 for all shifted chips. It would be used as left shift for every programmatic access to special addresses. Such a change would allow us to kill m29f400bt.c which has buggy write functions anyway. Example for probing: /* Issue JEDEC Product ID Entry command */ chip_writeb(0xAA, bios + (0x5555 & mask) << shifted); chip_writeb(0x55, bios + (0x2AAA & mask) << shifted); chip_writeb(0x90, bios + (0x5555 & mask) << shifted); > + id2_offset = 2; > + else > + id2_offset = 1; > > /* Reset to get a clean state */ > chip_writeb(0xFF, bios); > @@ -58,7 +64,7 @@ int probe_82802ab(struct flashchip *flash) > programmer_delay(10); > > id1 = chip_readb(bios); > Arguably my "shifted" proposal suggests to use the following line for consistency: id1 = chip_readb(bios + 0x00 << shifted); > - id2 = chip_readb(bios + 0x01); > + id2 = chip_readb(bios + id2_offset); > id2 = chip_readb(bios + 0x01 << shifted); > > /* Leave ID mode */ > chip_writeb(0xFF, bios); > @@ -72,7 +78,7 @@ int probe_82802ab(struct flashchip *flash) > > /* Read the product ID location again. We should now see normal flash contents. */ > flashcontent1 = chip_readb(bios); > - flashcontent2 = chip_readb(bios + 0x01); > + flashcontent2 = chip_readb(bios + id2_offset); > > if (id1 == flashcontent1) > msg_cdbg(", id1 is normal flash content"); > @@ -177,41 +183,64 @@ void write_page_82802ab(chipaddr bios, uint8_t *src, > > int write_82802ab(struct flashchip *flash, uint8_t *buf) > { > - int i; > - int total_size = flash->total_size * 1024; > + int i, j, blocknum; > + int blockoffset = 0; > int page_size = flash->page_size; > chipaddr bios = flash->virtual_memory; > uint8_t *tmpbuf = malloc(page_size); > + struct eraseblock * blocks; > + int (*erase) (struct flashchip *flash, unsigned int blockaddr, > + unsigned int blocklen); > + > + /* find first erase layout with a working erase function */ > + for (i = 0; flash->block_erasers[i].block_erase == NULL && > + i < NUM_ERASEFUNCTIONS; i++); > + > + if (i == NUM_ERASEFUNCTIONS) > + { > + msg_perr("No working erase function found - can't write\n"); > + return -1; > + } > + msg_pdbg("Chosing block layout #%d\n", i); > + blocks = flash->block_erasers[i].eraseblocks; > + erase = flash->block_erasers[i].block_erase; > That's too clever to be risked for 0.9.2. I can't see obvious bugs, but this code triggers my "might break if included directly before a release" fear. > > if (!tmpbuf) { > msg_cerr("Could not allocate memory!\n"); > exit(1); > } > - msg_cinfo("Programming page: \n"); > - for (i = 0; i < total_size / page_size; i++) { > - msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b"); > - msg_cinfo("%04d at address: 0x%08x", i, i * page_size); > - > - /* Auto Skip Blocks, which already contain the desired data > - * Faster, because we only write, what has changed > - * More secure, because blocks, which are excluded > - * (with the exclude or layout feature) > - * or not erased and rewritten; their data is retained also in > - * sudden power off situations > - */ > - chip_readn(tmpbuf, bios + i * page_size, page_size); > - if (!memcmp((void *)(buf + i * page_size), tmpbuf, page_size)) { > - msg_cdbg("SKIPPED\n"); > - continue; > - } > - > - /* erase block by block and write block by block; this is the most secure way */ > - if (erase_block_82802ab(flash, i * page_size, page_size)) { > - msg_cerr("ERASE FAILED!\n"); > - return -1; > + msg_cinfo("Programming block: \n"); > + blocknum = 0; > + for (i = 0; blocks[i].size != 0; i++) { > This is guaranteed access random data if a chip has NUM_ERASEREGIONS erase regions for a particular erase function. Either check for i<NUM_ERASEREGIONS as well or use the chip size as upper limit. The chip size check is probably more difficult here. > + for(j = 0; j < blocks[i].count; j++) { > + msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b" > + "\b\b\b\b\b\b\b\b\b\b\b"); > + msg_cinfo("%04d at address: 0x%08x", blocknum, > + blockoffset); > + > + /* Auto Skip Blocks, which already contain the > + * desired data: > + * Faster, because we only write, what has changed > + * More secure, because blocks, which are excluded > + * (with the exclude or layout feature) > + * or not erased and rewritten; their data is > + * retained also in sudden power off situations > + */ > + chip_readn(tmpbuf, bios + blockoffset, blocks[i].size); > + if (!memcmp((void *)(buf + i * page_size), tmpbuf, > + blocks[i].size)) { > + msg_cdbg("SKIPPED\n"); > + } else { > + if (erase(flash, blockoffset, page_size)) { > + msg_cerr("ERASE FAILED!\n"); > + return -1; > + } > + write_page_82802ab(bios, buf + blockoffset, > + bios + blockoffset, blocks[i].size); > + } > + blockoffset += blocks[i].size; > + blocknum++; > } > - write_page_82802ab(bios, buf + i * page_size, > - bios + i * page_size, page_size); > To be honest, I think the current code in write_82802ab() is something that should be ripped out and destroyed. It is essentially special-casing partial writes for a family of chips instead of doing it correctly in the generic code. The conversion to partial writes will happen post 0.9.2 anyway, and then this code will be ripped out completely. Your changes, on the other hand, beat at least some sanity into the code, so it would be desirable to have them in generic code post-0.9.2. Please coordinate with David Hendricks who is working on partial flashing. > } > msg_cinfo("DONE!\n"); > free(tmpbuf); > diff --git a/chipdrivers.h b/chipdrivers.h > index 6d5cef0..816088a 100644 > --- a/chipdrivers.h > +++ b/chipdrivers.h > @@ -53,6 +53,9 @@ int spi_nbyte_read(int addr, uint8_t *bytes, int len); > int spi_read_chunked(struct flashchip *flash, uint8_t *buf, int start, int len, int chunksize); > int spi_aai_write(struct flashchip *flash, uint8_t *buf); > > +/* i28f00x.c */ > +int write_28f00x(struct flashchip *flash, uint8_t *buf); > I don't see that function anywhere. Did you forget to svn add? Or was this some aborted attempt? > + > /* 82802ab.c */ > uint8_t wait_82802ab(chipaddr bios); > int probe_82802ab(struct flashchip *flash); > diff --git a/flashchips.c b/flashchips.c > index 2dbc1e0..f838ab2 100644 > --- a/flashchips.c > +++ b/flashchips.c > @@ -2385,6 +2385,116 @@ struct flashchip flashchips[] = { > > { > .vendor = "Intel", > + .name = "28F004BV/BE-B", > + .bustype = CHIP_BUSTYPE_PARALLEL, > + }, > + > + { > + .vendor = "Intel", > + .name = "28F004BV/BE-T", > + .bustype = CHIP_BUSTYPE_PARALLEL, > + }, > + > + { > + .vendor = "Intel", > + .name = "28F400BV/CV/CE-B", > + .bustype = CHIP_BUSTYPE_PARALLEL, > + .feature_bits = FEATURE_ADDR_SHIFTED, > + }, > + > + { > + .vendor = "Intel", > + .name = "28F004BV/BE-T", > That name is identical to the one two chips above AFAICS. > + .bustype = CHIP_BUSTYPE_PARALLEL, > + .feature_bits = FEATURE_ADDR_SHIFTED, > So the bottom two chips have the address left-shifted by 1 bit, but use full address size? Suggestions: How about pointing the FEATURE_ADDR_SHIFTED chips to a to-be-fixed m29f400bt.c for now? It would reduce jedec.c changes a bit. How about using erase_flash() in write_82802ab() and dropping any rolling reflash mechanism until post 0.9.2? It should solve all non-uniform sector stuff. While that's a fear-reaching change as well, I believe it makes the code more reviewable, and does allow us to kill more duplicated code. As an added benefit, conversion to partial write will be easier. Regards, Carl-Daniel -- http://www.hailfinger.org/

3 5

flashrom -E on an MSI 790FX-GD70
by Christian Schubert 01 Apr '10

01 Apr '10

Hi there, $ flashrom -E flashrom v0.9.1-r946 No coreboot table found. sh: dmidecode: not found Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Calibrating delay loop... OK. Found chip "Winbond W25x80" (1024 KB, SPI) at physical address 0xfff00000. === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Erasing flash chip... SUCCESS. ... seems to work pretty well :-) (programming & verifying also seems to work, didn't reboot yet) Let me know if you need more info. Thanks for one great tool, Christian

1 1

Hardware Sequencing vs Software Sequencing
by john warwick 01 Apr '10

01 Apr '10

Hi, I was looking through the code, and see that flashrom is using software sequencing. Is there any reason for software sequencing to be chosen instead of hardware sequencing? Are there any restrictions imposed for hardware sequencing? Rgds, John _________________________________________________________________ Hotmail: Trusted email with powerful SPAM protection. http://clk.atdmt.com/GBL/go/210850553/direct/01/

2 3

[PATCH] Fix the delay loop
by Carl-Daniel Hailfinger 01 Apr '10

01 Apr '10

[Side note: This is not the big timing code rewrite I originally wanted to post. I decided to focus on readable code instead of clever code. My other rewrite is available on request if anyone is interested.] The current delay loop calculation is still from revision 1 of flashrom, and since then it had a logic bug which caused all delays to be twice as long as intended. Fix the delay duration. Protect against delay loop overflows. Detect a non-working delay loop. Change the delay loop itself to ensure clever compiler optimizers won't eliminate it (as happens with clang/llvm in the current code). Some people suggested machine-specific asm, but the empty asm statement with the loop counter as register/memory input has the benefit of being perfectly cross-platform and working in gcc and clang. If time goes backwards (catastrophical NTP time difference, manual time change), timing measurements were shot because the new-old time subtraction yielded negative numbers which weren't handled correctly because the variable is unsigned. Simply return 1 microsecond timing in that case. If time goes forward too fast, pick the biggest possible timing measurement with a guaranteed overflow avoidance for all timing calculations. Check four times if the calculated timing is at most 10% too fast. This addresses OS scheduler interactions, e.g. being scheduled out during measurement which inflates measurements. If the timing is off, recalculate the timer values up to four times before giving up. Avoid division by zero in rare cases where timing measurements for a 250 ms delay return 0 us elapsed. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-delayloop_portable_fix/udelay.c =================================================================== --- flashrom-delayloop_portable_fix/udelay.c (Revision 988) +++ flashrom-delayloop_portable_fix/udelay.c (Arbeitskopie) @@ -24,13 +24,16 @@ #include <limits.h> #include "flash.h" -// count to a billion. Time it. If it's < 1 sec, count to 10B, etc. +/* loops per microsecond */ unsigned long micro = 1; -void myusec_delay(int usecs) +__attribute__ ((noinline)) void myusec_delay(int usecs) { - volatile unsigned long i; - for (i = 0; i < usecs * micro; i++) ; + unsigned long i; + for (i = 0; i < usecs * micro; i++) { + /* Make sure the compiler doesn't optimize the loop away. */ + asm volatile ("" : : "rm" (i) ); + } } unsigned long measure_delay(int usecs) @@ -43,30 +46,62 @@ gettimeofday(&end, 0); timeusec = 1000000 * (end.tv_sec - start.tv_sec) + (end.tv_usec - start.tv_usec); + /* Protect against time going forward too much. */ + if ((end.tv_sec > start.tv_sec) && + ((end.tv_sec - start.tv_sec) >= LONG_MAX / 1000000 - 1)) + timeusec = LONG_MAX; + /* Protect against time going backwards during leap seconds. */ + if ((end.tv_sec < start.tv_sec) || (timeusec > LONG_MAX)) + timeusec = 1; return timeusec; } void myusec_calibrate_delay(void) { - int count = 1000; + unsigned long count = 1000; unsigned long timeusec; - int ok = 0; + int i, tries = 0; printf("Calibrating delay loop... "); - while (!ok) { +recalibrate: + while (1) { timeusec = measure_delay(count); + if (timeusec > 1000000 / 4) + break; + if (count >= ULONG_MAX / 2) { + msg_pinfo("timer loop overflow, reduced precision. "); + break; + } count *= 2; - if (timeusec < 1000000 / 4) - continue; - ok = 1; } + tries ++; - // compute one microsecond. That will be count / time - micro = count / timeusec; - msg_pdbg("%ldM loops per second, ", micro); + /* Avoid division by zero, but in that case the loop is shot anyway. */ + if (!timeusec) + timeusec = 1; + + /* Compute rounded up number of loops per microsecond. */ + micro = (count * micro) / timeusec + 1; + msg_pdbg("%luM loops per second, ", micro); + /* Did we try to recalibrate less than 5 times? */ + if (tries < 5) { + /* Recheck our timing to make sure we weren't just hitting + * a scheduler delay or something similar. + */ + for (i = 0; i < 4; i++) { + if (measure_delay(100) < 90) { + msg_pdbg("delay more than 10% too short, " + "recalculating... "); + goto recalibrate; + } + } + } else { + msg_perr("delay loop is unreliable, trying to continue "); + } + /* We're interested in the actual precision. */ timeusec = measure_delay(10); msg_pdbg("10 myus = %ld us, ", timeusec); -- http://www.hailfinger.org/

3 4

[commit] r990 - trunk
by repository service 01 Apr '10

01 Apr '10

Author: hailfinger Date: Thu Apr 1 01:55:06 2010 New Revision: 990 URL: http://flashrom.org/trac/coreboot/changeset/990 Log: The current delay loop calculation is still from revision 1 of flashrom, and since then it had a logic bug which caused all delays to be twice as long as intended. Fix the delay duration. Protect against delay loop overflows. Detect a non-working delay loop. Change the delay loop itself to ensure clever compiler optimizers won't eliminate it (as happens with clang/llvm in the current code). Some people suggested machine-specific asm, but the empty asm statement with the loop counter as register/memory input has the benefit of being perfectly cross-platform and working in gcc and clang. If time goes backwards (catastrophical NTP time difference, manual time change), timing measurements were shot because the new-old time subtraction yielded negative numbers which weren't handled correctly because the variable is unsigned. Work around that issue (a fix is mathematically impossible). If time goes forward too fast, pick the biggest possible timing measurement with a guaranteed overflow avoidance for all timing calculations. Check four times if the calculated timing is at most 10% too fast. This addresses OS scheduler interactions, e.g. being scheduled out during measurement which inflates measurements. If the timing looks like garbage, recalculate the timer values up to four times before giving up. Avoid division by zero in rare cases where timing measurements for a 250 ms delay returned 0 us elapsed. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Maciej Pijanka <maciej.pijanka(a)gmail.com> Modified: trunk/udelay.c Modified: trunk/udelay.c ============================================================================== --- trunk/udelay.c Tue Mar 30 04:45:18 2010 (r989) +++ trunk/udelay.c Thu Apr 1 01:55:06 2010 (r990) @@ -24,13 +24,16 @@ #include <limits.h> #include "flash.h" -// count to a billion. Time it. If it's < 1 sec, count to 10B, etc. +/* loops per microsecond */ unsigned long micro = 1; -void myusec_delay(int usecs) +__attribute__ ((noinline)) void myusec_delay(int usecs) { - volatile unsigned long i; - for (i = 0; i < usecs * micro; i++) ; + unsigned long i; + for (i = 0; i < usecs * micro; i++) { + /* Make sure the compiler doesn't optimize the loop away. */ + asm volatile ("" : : "rm" (i) ); + } } unsigned long measure_delay(int usecs) @@ -43,29 +46,61 @@ gettimeofday(&end, 0); timeusec = 1000000 * (end.tv_sec - start.tv_sec) + (end.tv_usec - start.tv_usec); + /* Protect against time going forward too much. */ + if ((end.tv_sec > start.tv_sec) && + ((end.tv_sec - start.tv_sec) >= LONG_MAX / 1000000 - 1)) + timeusec = LONG_MAX; + /* Protect against time going backwards during leap seconds. */ + if ((end.tv_sec < start.tv_sec) || (timeusec > LONG_MAX)) + timeusec = 1; return timeusec; } void myusec_calibrate_delay(void) { - int count = 1000; + unsigned long count = 1000; unsigned long timeusec; - int ok = 0; + int i, tries = 0; printf("Calibrating delay loop... "); - while (!ok) { +recalibrate: + while (1) { timeusec = measure_delay(count); + if (timeusec > 1000000 / 4) + break; + if (count >= ULONG_MAX / 2) { + msg_pinfo("timer loop overflow, reduced precision. "); + break; + } count *= 2; - if (timeusec < 1000000 / 4) - continue; - ok = 1; } + tries ++; - // compute one microsecond. That will be count / time - micro = count / timeusec; - msg_pdbg("%ldM loops per second, ", micro); + /* Avoid division by zero, but in that case the loop is shot anyway. */ + if (!timeusec) + timeusec = 1; + + /* Compute rounded up number of loops per microsecond. */ + micro = (count * micro) / timeusec + 1; + msg_pdbg("%luM loops per second, ", micro); + + /* Did we try to recalibrate less than 5 times? */ + if (tries < 5) { + /* Recheck our timing to make sure we weren't just hitting + * a scheduler delay or something similar. + */ + for (i = 0; i < 4; i++) { + if (measure_delay(100) < 90) { + msg_pdbg("delay more than 10% too short, " + "recalculating... "); + goto recalibrate; + } + } + } else { + msg_perr("delay loop is unreliable, trying to continue "); + } /* We're interested in the actual precision. */ timeusec = measure_delay(10);

1 0

[PATCH] Intel 28F004/28F400 support
by Michael Karcher 01 Apr '10

01 Apr '10

This should also fix broken write for non-uniform sectored FWH-like chips. These are: Intel 28F001 Sharp LHF00L04 ST M50FW002 ST M50LPW116 Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> --- 82802ab.c | 85 +++++++++++++++++++++++++++++-------------- chipdrivers.h | 3 ++ flash.h | 2 +- flashchips.c | 110 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ flashchips.h | 4 ++ 5 files changed, 175 insertions(+), 29 deletions(-) diff --git a/82802ab.c b/82802ab.c index aa7e45e..27acaa3 100644 --- a/82802ab.c +++ b/82802ab.c @@ -48,6 +48,12 @@ int probe_82802ab(struct flashchip *flash) chipaddr bios = flash->virtual_memory; uint8_t id1, id2; uint8_t flashcontent1, flashcontent2; + int id2_offset; + + if (flash->feature_bits & FEATURE_ADDR_SHIFTED) + id2_offset = 2; + else + id2_offset = 1; /* Reset to get a clean state */ chip_writeb(0xFF, bios); @@ -58,7 +64,7 @@ int probe_82802ab(struct flashchip *flash) programmer_delay(10); id1 = chip_readb(bios); - id2 = chip_readb(bios + 0x01); + id2 = chip_readb(bios + id2_offset); /* Leave ID mode */ chip_writeb(0xFF, bios); @@ -72,7 +78,7 @@ int probe_82802ab(struct flashchip *flash) /* Read the product ID location again. We should now see normal flash contents. */ flashcontent1 = chip_readb(bios); - flashcontent2 = chip_readb(bios + 0x01); + flashcontent2 = chip_readb(bios + id2_offset); if (id1 == flashcontent1) msg_cdbg(", id1 is normal flash content"); @@ -177,41 +183,64 @@ void write_page_82802ab(chipaddr bios, uint8_t *src, int write_82802ab(struct flashchip *flash, uint8_t *buf) { - int i; - int total_size = flash->total_size * 1024; + int i, j, blocknum; + int blockoffset = 0; int page_size = flash->page_size; chipaddr bios = flash->virtual_memory; uint8_t *tmpbuf = malloc(page_size); + struct eraseblock * blocks; + int (*erase) (struct flashchip *flash, unsigned int blockaddr, + unsigned int blocklen); + + /* find first erase layout with a working erase function */ + for (i = 0; flash->block_erasers[i].block_erase == NULL && + i < NUM_ERASEFUNCTIONS; i++); + + if (i == NUM_ERASEFUNCTIONS) + { + msg_perr("No working erase function found - can't write\n"); + return -1; + } + msg_pdbg("Chosing block layout #%d\n", i); + blocks = flash->block_erasers[i].eraseblocks; + erase = flash->block_erasers[i].block_erase; if (!tmpbuf) { msg_cerr("Could not allocate memory!\n"); exit(1); } - msg_cinfo("Programming page: \n"); - for (i = 0; i < total_size / page_size; i++) { - msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b"); - msg_cinfo("%04d at address: 0x%08x", i, i * page_size); - - /* Auto Skip Blocks, which already contain the desired data - * Faster, because we only write, what has changed - * More secure, because blocks, which are excluded - * (with the exclude or layout feature) - * or not erased and rewritten; their data is retained also in - * sudden power off situations - */ - chip_readn(tmpbuf, bios + i * page_size, page_size); - if (!memcmp((void *)(buf + i * page_size), tmpbuf, page_size)) { - msg_cdbg("SKIPPED\n"); - continue; - } - - /* erase block by block and write block by block; this is the most secure way */ - if (erase_block_82802ab(flash, i * page_size, page_size)) { - msg_cerr("ERASE FAILED!\n"); - return -1; + msg_cinfo("Programming block: \n"); + blocknum = 0; + for (i = 0; blocks[i].size != 0; i++) { + for(j = 0; j < blocks[i].count; j++) { + msg_cinfo("\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b\b" + "\b\b\b\b\b\b\b\b\b\b\b"); + msg_cinfo("%04d at address: 0x%08x", blocknum, + blockoffset); + + /* Auto Skip Blocks, which already contain the + * desired data: + * Faster, because we only write, what has changed + * More secure, because blocks, which are excluded + * (with the exclude or layout feature) + * or not erased and rewritten; their data is + * retained also in sudden power off situations + */ + chip_readn(tmpbuf, bios + blockoffset, blocks[i].size); + if (!memcmp((void *)(buf + i * page_size), tmpbuf, + blocks[i].size)) { + msg_cdbg("SKIPPED\n"); + } else { + if (erase(flash, blockoffset, page_size)) { + msg_cerr("ERASE FAILED!\n"); + return -1; + } + write_page_82802ab(bios, buf + blockoffset, + bios + blockoffset, blocks[i].size); + } + blockoffset += blocks[i].size; + blocknum++; } - write_page_82802ab(bios, buf + i * page_size, - bios + i * page_size, page_size); } msg_cinfo("DONE!\n"); free(tmpbuf); diff --git a/chipdrivers.h b/chipdrivers.h index 6d5cef0..816088a 100644 --- a/chipdrivers.h +++ b/chipdrivers.h @@ -53,6 +53,9 @@ int spi_nbyte_read(int addr, uint8_t *bytes, int len); int spi_read_chunked(struct flashchip *flash, uint8_t *buf, int start, int len, int chunksize); int spi_aai_write(struct flashchip *flash, uint8_t *buf); +/* i28f00x.c */ +int write_28f00x(struct flashchip *flash, uint8_t *buf); + /* 82802ab.c */ uint8_t wait_82802ab(chipaddr bios); int probe_82802ab(struct flashchip *flash); diff --git a/flash.h b/flash.h index aee95a3..0a74363 100644 --- a/flash.h +++ b/flash.h @@ -166,7 +166,7 @@ enum chipbustype { #define FEATURE_ADDR_MASK (3 << 2) #define FEATURE_ADDR_2AA (1 << 2) #define FEATURE_ADDR_AAA (2 << 2) -#define FEATURE_ADDR_SHIFTED 0 +#define FEATURE_ADDR_SHIFTED (1 << 5) struct flashchip { const char *vendor; diff --git a/flashchips.c b/flashchips.c index 2dbc1e0..f838ab2 100644 --- a/flashchips.c +++ b/flashchips.c @@ -2385,6 +2385,116 @@ struct flashchip flashchips[] = { { .vendor = "Intel", + .name = "28F004BV/BE-B", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F004BB, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {16 * 1024, 1}, + {8 * 1024, 2}, + {96 * 1024, 1}, + {128 * 1024, 3}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F004BV/BE-T", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F004BT, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {128 * 1024, 3}, + {96 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F400BV/CV/CE-B", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F400BB, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .feature_bits = FEATURE_ADDR_SHIFTED, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {16 * 1024, 1}, + {8 * 1024, 2}, + {96 * 1024, 1}, + {128 * 1024, 3}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", + .name = "28F004BV/BE-T", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F400BT, + .total_size = 512, + .page_size = 128 * 1024, /* maximal block size */ + .feature_bits = FEATURE_ADDR_SHIFTED, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { + {128 * 1024, 3}, + {96 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_block_82802ab, + }, + }, + .write = write_82802ab, + .read = read_memmapped, + }, + + { + .vendor = "Intel", .name = "82802AB", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = INTEL_ID, diff --git a/flashchips.h b/flashchips.h index 4337e52..b6c2e8b 100644 --- a/flashchips.h +++ b/flashchips.h @@ -259,6 +259,10 @@ #define E_28F016S5 0xAA #define P28F001BXT 0x94 /* 28F001BX-T */ #define P28F001BXB 0x95 /* 28F001BX-B */ +#define P28F004BT 0x78 /* 28F004BV/BE-T */ +#define P28F004BB 0x79 /* 28F004BV/BE-B */ +#define P28F400BT 0x70 /* 28F400BV/CV/CE-T */ +#define P28F400BB 0x71 /* 28F400BV/CV/CE-B */ #define SHARP_LH28F008SA 0xA2 /* Sharp chip, Intel Vendor ID */ #define SHARP_LH28F008SC 0xA6 /* Sharp chip, Intel Vendor ID */ -- 1.7.0

1 0

Re: [flashrom] [PATCH] Intel 28F004/28F400 support
by Michael Karcher 01 Apr '10

01 Apr '10

Am Donnerstag, den 01.04.2010, 00:42 +0200 schrieb Michael Karcher: > This should also fix broken write for non-uniform sectored FWH-like chips. Sorry, that patch was broken. Real patch follows. Regards, Michael Karcher

1 0

[PATCH] Intel 28F004/28F400 support
by Michael Karcher 01 Apr '10

01 Apr '10

This should also fix broken write for non-uniform sectored FWH-like chips. These are: Intel 28F001 Sharp LHF00L04 ST M50FW002 ST M50LPW116 Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> --- Makefile | 2 +- chipdrivers.h | 3 +++ flashchips.c | 31 +++++++++++++++++++++++++++++++ flashchips.h | 2 ++ 4 files changed, 37 insertions(+), 1 deletions(-) diff --git a/Makefile b/Makefile index fa67b73..992397e 100644 --- a/Makefile +++ b/Makefile @@ -57,7 +57,7 @@ endif CHIP_OBJS = jedec.o stm50flw0x0x.o w39v040c.o w39v080fa.o w29ee011.o \ sst28sf040.o m29f400bt.o 82802ab.o pm49fl00x.o \ - sst49lfxxxc.o sst_fwhub.o flashchips.o spi.o spi25.o + sst49lfxxxc.o sst_fwhub.o flashchips.o spi.o spi25.o i28f00x.o LIB_OBJS = layout.o diff --git a/chipdrivers.h b/chipdrivers.h index 6d5cef0..816088a 100644 --- a/chipdrivers.h +++ b/chipdrivers.h @@ -53,6 +53,9 @@ int spi_nbyte_read(int addr, uint8_t *bytes, int len); int spi_read_chunked(struct flashchip *flash, uint8_t *buf, int start, int len, int chunksize); int spi_aai_write(struct flashchip *flash, uint8_t *buf); +/* i28f00x.c */ +int write_28f00x(struct flashchip *flash, uint8_t *buf); + /* 82802ab.c */ uint8_t wait_82802ab(chipaddr bios); int probe_82802ab(struct flashchip *flash); diff --git a/flashchips.c b/flashchips.c index 2dbc1e0..68f9ecd 100644 --- a/flashchips.c +++ b/flashchips.c @@ -2385,6 +2385,37 @@ struct flashchip flashchips[] = { { .vendor = "Intel", + .name = "28F004BV/BE-T", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = INTEL_ID, + .model_id = P28F004BT, + .total_size = 512, + .page_size = 128 * 1024, /* for write_i28f00x: maximal block size */ + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .erase = NULL, + .block_erasers = + { + { + /* Keep this the first block_erasers + entry. The write functions spies here to + get the chip layout */ + .eraseblocks = { + {128 * 1024, 3}, + {96 * 1024, 1}, + {8 * 1024, 2}, + {16 * 1024, 1}, + }, + .block_erase = erase_82802ab_block, + }, + }, + .write = write_28f00x, + .read = read_memmapped, + }, + + { + .vendor = "Intel", .name = "82802AB", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = INTEL_ID, diff --git a/flashchips.h b/flashchips.h index 4337e52..1cbb3c6 100644 --- a/flashchips.h +++ b/flashchips.h @@ -259,6 +259,8 @@ #define E_28F016S5 0xAA #define P28F001BXT 0x94 /* 28F001BX-T */ #define P28F001BXB 0x95 /* 28F001BX-B */ +#define P28F004BT 0x78 /* 28F004BV/BE-T */ +#define P28F004BB 0x79 /* 28F004BV/BE-B */ #define SHARP_LH28F008SA 0xA2 /* Sharp chip, Intel Vendor ID */ #define SHARP_LH28F008SC 0xA6 /* Sharp chip, Intel Vendor ID */ -- 1.7.0

1 0

HP dc5850 Dump Files
by Terminus Est 31 Mar '10

31 Mar '10

Flashrom doesnt read, write or erase on this mobo bios. I can't open my PC to clear the cmos settings, and don't remember the bios password. I need to access the bios to configure somethings. Maybe you have a tip, a clue? Thx in advance. -- Linux User nº 451568 Linux Mint Gloria KDE Edition running on Athlon 64 X2 4200+ 2Gb DDR-400 2x Maxtor 40Gb in RAID 0 SATA Samsung 160Gb A8N SLI Premium gForce 6800 GS Ultra - Deceased...

1 0

Flashrom on Gigabyte GA-MA770-UD3 (rev 1.0) - works with little patch
by Vadim Girlin 30 Mar '10

30 Mar '10

Hello, Flashrom v0.9.1-r985 was unable to detect SPI flash chip (SST25VF080B) on Gigabyte GA-MA770-UD3 (rev 1.0) - http://www.gigabyte.com.tw/Products/Motherboard/Products_Spec.aspx?ProductI… First attachment contains the output of "flashrom -r -V". I've tried the following: Index: it87spi.c =================================================================== --- it87spi.c (revision 985) +++ it87spi.c (working copy) @@ -103,6 +103,7 @@ switch (id) { case 0x8716: case 0x8718: + case 0x8720: enter_conf_mode_ite(port); /* NOLDN, reg 0x24, mask out lowest bit (suspend) */ tmp = sio_read(port, 0x24) & 0xFE; After this patch flashrom detected the chip. Reading, erasing and writing also works. I attached the logs. Hope this helps. -- Best regards, Vadim Girlin

2 3

[commit] r989 - trunk
by repository service 30 Mar '10

30 Mar '10

Author: hailfinger Date: Tue Mar 30 04:45:18 2010 New Revision: 989 URL: http://flashrom.org/trac/coreboot/changeset/989 Log: Add ITE IT8720 SPI support. Original patch by Vadim Girlin. Message printing updated by Carl-Daniel Hailfinger. Signed-off-by: Vadim Girlin <vadimgirlin(a)gmail.com> Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/it87spi.c Modified: trunk/it87spi.c ============================================================================== --- trunk/it87spi.c Sun Mar 28 00:25:14 2010 (r988) +++ trunk/it87spi.c Tue Mar 30 04:45:18 2010 (r989) @@ -103,6 +103,7 @@ switch (id) { case 0x8716: case 0x8718: + case 0x8720: enter_conf_mode_ite(port); /* NOLDN, reg 0x24, mask out lowest bit (suspend) */ tmp = sio_read(port, 0x24) & 0xFE; @@ -159,7 +160,7 @@ break; /* TODO: Handle more IT87xx if they support flash translation */ default: - msg_pinfo("SuperI/O ID %04hx is not on the controller list.\n", id); + msg_pdbg("SuperI/O ID %04hx is not on the controller list.\n", id); } return flashport; } @@ -199,8 +200,11 @@ int ret; ret = it87spi_common_init(); - if (!ret) + if (!ret) { + if (buses_supported & CHIP_BUSTYPE_SPI) + msg_pdbg("Overriding chipset SPI with IT87 SPI.\n"); buses_supported |= CHIP_BUSTYPE_SPI; + } return ret; }

1 0

SST 49LF0008A - Erase problem (and solution)
by Panino ColSalame 29 Mar '10

29 Mar '10

Hello, I'm playing with flashrom on an ASEM Industrial PC based on an Atom Z530 and the US15W (Poulsbo) System Controller Hub. The BIOS flash is the SST 49LF0008A (Firmware Hub). After downloading the latest development code using git, flashrom was able to detect and read the flash, but the erase command failed. At first I've tried to increase the delay that is used by the toggle functions in jedec.c, passing from the default 8 to 80 (just for testing). At this point, the Erase command started to work properly. SST manual reads: The End-of-Write detection mode is incorporated into the FWH Read cycle. The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or Toggle Bit read may be simultaneous with the completion of the Write cycle. If this occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with either DQ7 or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software routine should include a loop to read the accessed location an additional two (2) times. If both reads are valid, then the device has completed the Write cycle, otherwise the rejection is valid. So, I've set the delay for reading the toggle bit again to the default value of 8 and I've added an additional toggle bit check, in case the first one seems to be ok. It works! So, I'm able to Read, Write and Erase the chip. Best Regards Panino diff -Nur flashromold/jedec.c flashromnew/jedec.c --- flashromold/jedec.c 2010-03-08 14:07:23.000000000 +0100 +++ flashromnew/jedec.c 2010-03-08 13:29:30.000000000 +0100 @@ -50,7 +50,11 @@ programmer_delay(delay); tmp2 = chip_readb(dst) & 0x40; if (tmp1 == tmp2) { - break; + tmp1 = chip_readb(dst) & 0x40; + programmer_delay(delay); + tmp2 = chip_readb(dst) & 0x40; + if (tmp1 == tmp2) + break; } tmp1 = tmp2; } _________________________________________________________________ Personalizza il tuo Messenger con nuove e divertenti Emoticon http://www.pimpit.it/emoticon.html

3 2

Flashrom integration in SMGL
by Quentin RAMEAU 28 Mar '10

28 Mar '10

Hi, just a quick word to say that flashrom has been integrated in Source Mage GNU/Linux distribition, versions 0.9.1 and svn. 'cast flashrom' to install it.

2 1

flashrom -V for M3A78-CM
by Quentin RAMEAU 28 Mar '10

28 Mar '10

Here is some data from M3A78-CM Asus motherboard # flashrom -V flashrom v0.9.1-r988 on Linux 2.6.33.1 (x86_64), built with libpci 3.1.7, GCC 4.3.3 No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M3A78-CM" DMI string baseboard-version: "Rev X.0x" DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8712 Found chipset "AMD SB700/SB710/SB750", enabling flash write... SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=0, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=0, SpiBridgeDisable=0, DropOneClkOnRd=0 GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK ROM strap override is not active OK. This chipset supports the following protocols: LPC,FWH,SPI. SuperI/O ID 8712 is not on the controller list. Calibrating delay loop... 662M loops per second, 10 myus = 21 us, 100 myus = 191 us, 1000 myus = 2029 us, 10000 myus = 20679 us, OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 KB: skipped. Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN29F010, 128 KB: skipped. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x24, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS S29C31004T, 512 KB: skipped. Probing for SyncMOS S29C51001T, 128 KB: skipped. Probing for SyncMOS S29C51002T, 256 KB: skipped. Probing for SyncMOS S29C51004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x00, id2 0x08, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x41, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xad, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. probe_spi_rems: id1 0xc2, id2 0x13 Not unmapping zero size at (nil) === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === No operations were specified.

1 0

[PATCH] Support for PCM Pm39LV020 and Pm39LV040
by Anders Juel Jensen 28 Mar '10

28 Mar '10

According to the data sheet these are identical to the 39LV010 in every respect except capacity. Unfortunately I can't test this, as I am on a laptop. Flashrom simply doesn't detect the chip. Signed-of-by: Anders Juel Jensen <andersjjensen(a)gmail.com>

3 6

[commit] r988 - trunk
by repository service 28 Mar '10

28 Mar '10

Author: hailfinger Date: Sun Mar 28 00:25:14 2010 New Revision: 988 URL: http://flashrom.org/trac/coreboot/changeset/988 Log: Add PMC Pm39LV020 and Pm39LV040. Signed-off-by: Anders Juel Jensen <andersjjensen(a)gmail.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/flashchips.c Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Sat Mar 27 17:36:40 2010 (r987) +++ trunk/flashchips.c Sun Mar 28 00:25:14 2010 (r988) @@ -3326,7 +3326,7 @@ .name = "Pm39LV010", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = PMC_ID_NOPREFIX, - .model_id = PMC_39F010, + .model_id = PMC_39F010, /* Pm39LV010 and Pm39F010 have identical IDs but different voltage */ .total_size = 128, .page_size = 4096, .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET, @@ -3352,6 +3352,64 @@ { .vendor = "PMC", + .name = "Pm39LV020", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = PMC_ID_NOPREFIX, + .model_id = PMC_39LV020, + .total_size = 256, + .page_size = 4096, + .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {64 * 1024, 4} }, + .block_erase = erase_block_jedec, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + }, + + { + .vendor = "PMC", + .name = "Pm39LV040", + .bustype = CHIP_BUSTYPE_PARALLEL, + .manufacture_id = PMC_ID_NOPREFIX, + .model_id = PMC_39LV040, + .total_size = 512, + .page_size = 4096, + .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET, + .tested = TEST_UNTESTED, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {64 * 1024, 8} }, + .block_erase = erase_block_jedec, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + }, + + { + .vendor = "PMC", .name = "Pm49FL002", .bustype = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH, /* A/A Mux*/ .manufacture_id = PMC_ID_NOPREFIX,

1 0

Unused functions...
by Carl-Daniel Hailfinger 27 Mar '10

27 Mar '10

We have a few unused functions in our codebase. Should we - mark then static (may cause gcc to complain if -Wunused-function is enabled) - put them inside #if 0 (code will bitrot) - remove them from the source base entirely (some may be used in the future) jedec.c: data_polling_jedec (maybe some chip in the future won't support toggle_jedec) stm50flw0x0x.c: erase_sector_stm50flw0x0x (keep?) m29f400bt.c: write_m29f400bt (hm, probably kill) 82802ab.c: erase_82802ab (kill, old-style erase) pm49fl00x.c: lock_49fl00x (for the future) sst49lfxxxc.c: unlock_block_49lfxxxc (strange, don't we use that?) spi.c: default_spi_send_command (if one chip driver ever supports only multicommand) spi25.c: spi_write_status_enable (we should use it, some chips require that) spi_write_disable (does that make sense?) spi_aai_write (need some write infrastructure changes for this) spi_chip_erase_d8 (kill) flashrom.c: chip_writel (will we ever need it?) chip_writen (this one might be usable for a few chip drivers) chip_readl (will we ever need it?) list_programmers (no idea) register_shutdown (needed for ECs) need_erase (needed for partial write) internal.c: pci_dev_find_filter (hmmm) Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom