- flashrom - mail.coreboot.org

[commit] r1293 - trunk
by repository service 04 May '11

04 May '11

Author: hailfinger Date: Wed May 4 02:39:50 2011 New Revision: 1293 URL: http://flashrom.org/trac/flashrom/changeset/1293 Log: Constify flashchips array. This moves 99.5% of the .data section to .rodata (which ends up in .text). Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Reinauer <stefan.reinauer(a)coreboot.org> Modified: trunk/cli_classic.c trunk/flash.h trunk/flashchips.c trunk/flashrom.c trunk/print.c trunk/print_wiki.c trunk/programmer.h Modified: trunk/cli_classic.c ============================================================================== --- trunk/cli_classic.c Tue May 3 23:49:41 2011 (r1292) +++ trunk/cli_classic.c Wed May 4 02:39:50 2011 (r1293) @@ -100,7 +100,11 @@ { unsigned long size; /* Probe for up to three flash chips. */ - struct flashchip *flash, *flashes[3]; + const struct flashchip *flash; + struct flashchip flashes[3]; + struct flashchip *fill_flash; + int startchip = 0; + int chipcount = 0; const char *name; int namelen; int opt; @@ -359,49 +363,47 @@ exit(1); } - /* FIXME: Delay calibration should happen in programmer code. */ for (i = 0; i < ARRAY_SIZE(flashes); i++) { - flashes[i] = - probe_flash(i ? flashes[i - 1] + 1 : flashchips, 0); - if (!flashes[i]) - for (i++; i < ARRAY_SIZE(flashes); i++) - flashes[i] = NULL; + startchip = probe_flash(startchip, &flashes[i], 0); + if (startchip == -1) + break; + chipcount++; } - if (flashes[1]) { + if (chipcount > 1) { printf("Multiple flash chips were detected:"); - for (i = 0; i < ARRAY_SIZE(flashes) && flashes[i]; i++) - printf(" %s", flashes[i]->name); + for (i = 0; i < chipcount; i++) + printf(" %s", flashes[i].name); printf("\nPlease specify which chip to use with the -c <chipname> option.\n"); programmer_shutdown(); exit(1); - } else if (!flashes[0]) { + } else if (!chipcount) { printf("No EEPROM/flash device found.\n"); if (!force || !chip_to_probe) { printf("Note: flashrom can never write if the flash chip isn't found automatically.\n"); } if (force && read_it && chip_to_probe) { printf("Force read (-f -r -c) requested, pretending the chip is there:\n"); - flashes[0] = probe_flash(flashchips, 1); - if (!flashes[0]) { + startchip = probe_flash(0, &flashes[0], 1); + if (startchip == -1) { printf("Probing for flash chip '%s' failed.\n", chip_to_probe); programmer_shutdown(); exit(1); } printf("Please note that forced reads most likely contain garbage.\n"); - return read_flash_to_file(flashes[0], filename); + return read_flash_to_file(&flashes[0], filename); } // FIXME: flash writes stay enabled! programmer_shutdown(); exit(1); } - flash = flashes[0]; + fill_flash = &flashes[0]; - check_chip_supported(flash); + check_chip_supported(fill_flash); - size = flash->total_size * 1024; - if (check_max_decode((buses_supported & flash->bustype), size) && + size = fill_flash->total_size * 1024; + if (check_max_decode((buses_supported & fill_flash->bustype), size) && (!force)) { fprintf(stderr, "Chip is too big for this programmer " "(-V gives details). Use --force to override.\n"); @@ -432,5 +434,5 @@ * Give the chip time to settle. */ programmer_delay(100000); - return doit(flash, force, filename, read_it, write_it, erase_it, verify_it); + return doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it); } Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Tue May 3 23:49:41 2011 (r1292) +++ trunk/flash.h Wed May 4 02:39:50 2011 (r1293) @@ -173,7 +173,7 @@ #define TIMING_IGNORED -1 #define TIMING_ZERO -2 -extern struct flashchip flashchips[]; +extern const struct flashchip flashchips[]; /* print.c */ char *flashbuses_to_text(enum chipbustype bustype); @@ -193,7 +193,7 @@ void map_flash_registers(struct flashchip *flash); int read_memmapped(struct flashchip *flash, uint8_t *buf, int start, int len); int erase_flash(struct flashchip *flash); -struct flashchip *probe_flash(struct flashchip *first_flash, int force); +int probe_flash(int startchip, struct flashchip *fill_flash, int force); int read_flash_to_file(struct flashchip *flash, char *filename); int min(int a, int b); int max(int a, int b); Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Tue May 3 23:49:41 2011 (r1292) +++ trunk/flashchips.c Wed May 4 02:39:50 2011 (r1293) @@ -32,7 +32,7 @@ * Please keep the list sorted by vendor name and chip name, so that * the output of 'flashrom -L' is alphabetically sorted. */ -struct flashchip flashchips[] = { +const struct flashchip flashchips[] = { /* * .vendor = Vendor name Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Tue May 3 23:49:41 2011 (r1292) +++ trunk/flashrom.c Wed May 4 02:39:50 2011 (r1293) @@ -1109,16 +1109,16 @@ return 1; } -struct flashchip *probe_flash(struct flashchip *first_flash, int force) +int probe_flash(int startchip, struct flashchip *fill_flash, int force) { - struct flashchip *flash; + const struct flashchip *flash; unsigned long base = 0; char location[64]; uint32_t size; enum chipbustype buses_common; char *tmp; - for (flash = first_flash; flash && flash->name; flash++) { + for (flash = flashchips + startchip; flash && flash->name; flash++) { if (chip_to_probe && strcmp(flash->name, chip_to_probe) != 0) continue; msg_gdbg("Probing for %s %s, %d KB: ", @@ -1145,25 +1145,35 @@ size = flash->total_size * 1024; check_max_decode(buses_common, size); + /* Start filling in the dynamic data. */ + *fill_flash = *flash; + base = flashbase ? flashbase : (0xffffffff - size + 1); - flash->virtual_memory = (chipaddr)programmer_map_flash_region("flash chip", base, size); + fill_flash->virtual_memory = (chipaddr)programmer_map_flash_region("flash chip", base, size); if (force) break; - if (flash->probe(flash) != 1) + if (fill_flash->probe(fill_flash) != 1) goto notfound; - if (first_flash == flashchips - || flash->model_id != GENERIC_DEVICE_ID) + /* If this is the first chip found, accept it. + * If this is not the first chip found, accept it only if it is + * a non-generic match. + * We could either make chipcount global or provide it as + * parameter, or we assume that startchip==0 means this call to + * probe_flash() is the first one and thus no chip has been + * found before. + */ + if (startchip == 0 || fill_flash->model_id != GENERIC_DEVICE_ID) break; notfound: - programmer_unmap_flash_region((void *)flash->virtual_memory, size); + programmer_unmap_flash_region((void *)fill_flash->virtual_memory, size); } if (!flash || !flash->name) - return NULL; + return -1; #if CONFIG_INTERNAL == 1 if (programmer_table[programmer].map_flash_region == physmap) @@ -1181,10 +1191,11 @@ * may be stored in registers, so avoid lock info printing. */ if (!force) - if (flash->printlock) - flash->printlock(flash); + if (fill_flash->printlock) + fill_flash->printlock(fill_flash); - return flash; + /* Return position of matching chip. */ + return flash - flashchips; } int verify_flash(struct flashchip *flash, uint8_t *buf) @@ -1293,7 +1304,7 @@ * walk_eraseregions(). * Even if an error is found, the function will keep going and check the rest. */ -static int selfcheck_eraseblocks(struct flashchip *flash) +static int selfcheck_eraseblocks(const struct flashchip *flash) { int i, j, k; int ret = 0; @@ -1670,7 +1681,7 @@ int selfcheck(void) { int ret = 0; - struct flashchip *flash; + const struct flashchip *flash; /* Safety check. Instead of aborting after the first error, check * if more errors exist. @@ -1689,7 +1700,7 @@ return ret; } -void check_chip_supported(struct flashchip *flash) +void check_chip_supported(const struct flashchip *flash) { if (TEST_OK_MASK != (flash->tested & TEST_OK_MASK)) { msg_cinfo("===\n"); Modified: trunk/print.c ============================================================================== --- trunk/print.c Tue May 3 23:49:41 2011 (r1292) +++ trunk/print.c Wed May 4 02:39:50 2011 (r1293) @@ -78,7 +78,7 @@ { int okcol = 0, pos = 0, i, chipcount = 0; int maxchiplen = 0, maxvendorlen = 0; - struct flashchip *f; + const struct flashchip *f; for (f = flashchips; f->name != NULL; f++) { /* Ignore "unknown XXXX SPI chip" entries. */ Modified: trunk/print_wiki.c ============================================================================== --- trunk/print_wiki.c Tue May 3 23:49:41 2011 (r1292) +++ trunk/print_wiki.c Wed May 4 02:39:50 2011 (r1293) @@ -201,7 +201,7 @@ static void print_supported_chips_wiki(int cols) { int i = 0, c = 1, chipcount = 0; - struct flashchip *f, *old = NULL; + const struct flashchip *f, *old = NULL; uint32_t t; for (f = flashchips; f->name != NULL; f++) Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Tue May 3 23:49:41 2011 (r1292) +++ trunk/programmer.h Wed May 4 02:39:50 2011 (r1293) @@ -515,7 +515,7 @@ extern struct decode_sizes max_rom_decode; extern int programmer_may_write; extern unsigned long flashbase; -void check_chip_supported(struct flashchip *flash); +void check_chip_supported(const struct flashchip *flash); int check_max_decode(enum chipbustype buses, uint32_t size); char *extract_programmer_param(char *param_name);

1 0

[PATCH] Revert MMIO space writes on shutdown as needed.
by Carl-Daniel Hailfinger 03 May '11

03 May '11

Revert MMIO space writes on shutdown as needed. Reversible MMIO space writes now use rmmio_write*(). MMIO space writes which are one-shot (e.g. communication with some chip) should continue to use the permanent mmio_write* variants. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-mmio_shutdown_restore/hwaccess.c =================================================================== --- flashrom-mmio_shutdown_restore/hwaccess.c (Revision 1234) +++ flashrom-mmio_shutdown_restore/hwaccess.c (Arbeitskopie) @@ -184,3 +184,71 @@ { return le_to_cpu32(mmio_readl(addr)); } + +enum mmio_write_type { + mmio_write_type_b, + mmio_write_type_w, + mmio_write_type_l, +}; + +struct undo_mmio_write_data { + void *addr; + int reg; + enum mmio_write_type type; + union { + uint8_t bdata; + uint16_t wdata; + uint32_t ldata; + }; +}; + +void undo_mmio_write(void *p) +{ + struct undo_mmio_write_data *data = p; + msg_pdbg("Restoring MMIO space at %p\n", data->addr); + switch (data->type) { + case mmio_write_type_b: + mmio_writeb(data->bdata, data->addr); + break; + case mmio_write_type_w: + mmio_writeb(data->wdata, data->addr); + break; + case mmio_write_type_l: + mmio_writeb(data->ldata, data->addr); + break; + } + /* p was allocated in register_undo_mmio_write. */ + free(p); +} + +#define register_undo_mmio_write(a, c) \ +{ \ + struct undo_mmio_write_data *undo_mmio_write_data; \ + undo_mmio_write_data = malloc(sizeof(struct undo_mmio_write_data)); \ + undo_mmio_write_data->addr = a; \ + undo_mmio_write_data->type = mmio_write_type_##c; \ + undo_mmio_write_data->c##data = mmio_read##c(a); \ + register_shutdown(undo_mmio_write, undo_mmio_write_data); \ +} + +#define register_undo_mmio_writeb(a) register_undo_mmio_write(a, b) +#define register_undo_mmio_writew(a) register_undo_mmio_write(a, w) +#define register_undo_mmio_writel(a) register_undo_mmio_write(a, l) + +void rmmio_writeb(uint8_t val, void *addr) +{ + register_undo_mmio_writeb(addr); + mmio_writeb(val, addr); +} + +void rmmio_writew(uint16_t val, void *addr) +{ + register_undo_mmio_writew(addr); + mmio_writew(val, addr); +} + +void rmmio_writel(uint32_t val, void *addr) +{ + register_undo_mmio_writel(addr); + mmio_writel(val, addr); +} Index: flashrom-mmio_shutdown_restore/ichspi.c =================================================================== --- flashrom-mmio_shutdown_restore/ichspi.c (Revision 1234) +++ flashrom-mmio_shutdown_restore/ichspi.c (Arbeitskopie) @@ -382,16 +382,16 @@ switch (spi_controller) { case SPI_CONTROLLER_ICH7: case SPI_CONTROLLER_VIA: - REGWRITE16(ICH7_REG_PREOP, preop); - REGWRITE16(ICH7_REG_OPTYPE, optype); - REGWRITE32(ICH7_REG_OPMENU, opmenu[0]); - REGWRITE32(ICH7_REG_OPMENU + 4, opmenu[1]); + rmmio_writew(preop, ich_spibar + ICH7_REG_PREOP); + rmmio_writew(optype, ich_spibar + ICH7_REG_OPTYPE); + rmmio_writew(opmenu[0], ich_spibar + ICH7_REG_OPMENU); + rmmio_writew(opmenu[1], ich_spibar + ICH7_REG_OPMENU + 4); break; case SPI_CONTROLLER_ICH9: - REGWRITE16(ICH9_REG_PREOP, preop); - REGWRITE16(ICH9_REG_OPTYPE, optype); - REGWRITE32(ICH9_REG_OPMENU, opmenu[0]); - REGWRITE32(ICH9_REG_OPMENU + 4, opmenu[1]); + rmmio_writew(preop, ich_spibar + ICH9_REG_PREOP); + rmmio_writew(optype, ich_spibar + ICH9_REG_OPTYPE); + rmmio_writew(opmenu[0], ich_spibar + ICH9_REG_OPMENU); + rmmio_writew(opmenu[1], ich_spibar + ICH9_REG_OPMENU + 4); break; default: msg_perr("%s: unsupported chipset\n", __func__); @@ -409,16 +409,20 @@ { switch (spi_controller) { case SPI_CONTROLLER_ICH7: - mmio_writel(minaddr, ich_spibar + 0x50); + rmmio_writel(minaddr, ich_spibar + 0x50); ichspi_bbar = mmio_readl(ich_spibar + 0x50); - /* We don't have any option except complaining. */ + /* We don't have any option except complaining. And if the write + * failed, the restore will fail as well, so no problem there. + */ if (ichspi_bbar != minaddr) msg_perr("Setting BBAR failed!\n"); break; case SPI_CONTROLLER_ICH9: - mmio_writel(minaddr, ich_spibar + 0xA0); + rmmio_writel(minaddr, ich_spibar + 0xA0); ichspi_bbar = mmio_readl(ich_spibar + 0xA0); - /* We don't have any option except complaining. */ + /* We don't have any option except complaining. And if the write + * failed, the restore will fail as well, so no problem there. + */ if (ichspi_bbar != minaddr) msg_perr("Setting BBAR failed!\n"); break; Index: flashrom-mmio_shutdown_restore/nicintel_spi.c =================================================================== --- flashrom-mmio_shutdown_restore/nicintel_spi.c (Revision 1234) +++ flashrom-mmio_shutdown_restore/nicintel_spi.c (Arbeitskopie) @@ -149,6 +149,7 @@ nicintel_spibar = physmap("Intel Gigabit NIC w/ SPI flash", io_base_addr, 4096); + /* Automatic restore is not possible because we only change two bits. */ tmp = pci_mmio_readl(nicintel_spibar + EECD); tmp &= ~FLASH_WRITES_DISABLED; tmp |= FLASH_WRITES_ENABLED; @@ -168,6 +169,7 @@ { uint32_t tmp; + /* Automatic restore is not possible because we only change two bits. */ tmp = pci_mmio_readl(nicintel_spibar + EECD); tmp &= ~FLASH_WRITES_ENABLED; tmp |= FLASH_WRITES_DISABLED; Index: flashrom-mmio_shutdown_restore/programmer.h =================================================================== --- flashrom-mmio_shutdown_restore/programmer.h (Revision 1234) +++ flashrom-mmio_shutdown_restore/programmer.h (Arbeitskopie) @@ -311,6 +311,9 @@ #define pci_mmio_readb mmio_le_readb #define pci_mmio_readw mmio_le_readw #define pci_mmio_readl mmio_le_readl +void rmmio_writeb(uint8_t val, void *addr); +void rmmio_writew(uint16_t val, void *addr); +void rmmio_writel(uint32_t val, void *addr); /* programmer.c */ int noop_shutdown(void); -- http://www.hailfinger.org/

2 4

[commit] r1292 - trunk
by repository service 03 May '11

03 May '11

Author: hailfinger Date: Tue May 3 23:49:41 2011 New Revision: 1292 URL: http://flashrom.org/trac/flashrom/changeset/1292 Log: Revert MMIO space writes on shutdown as needed. Reversible MMIO space writes now use rmmio_write*(). Reversible PCI MMIO space writes now use pci_rmmio_write*(). If a MMIO value needs to be queued for restore without writing it, use rmmio_val*(). MMIO space writes which are one-shot (e.g. communication with some chip) should continue to use the permanent mmio_write* variants. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> David tested it successfully on some NM10/ICH7 platforms which switch between SPI and LPC targets (x86 BIOS ROM vs. EC firmware ROM). Acked-by: David Hendricks <dhendrix(a)google.com> Modified: trunk/hwaccess.c trunk/ichspi.c trunk/nicintel_spi.c trunk/programmer.h trunk/satamv.c Modified: trunk/hwaccess.c ============================================================================== --- trunk/hwaccess.c Sat Apr 30 01:53:09 2011 (r1291) +++ trunk/hwaccess.c Tue May 3 23:49:41 2011 (r1292) @@ -184,3 +184,104 @@ { return le_to_cpu32(mmio_readl(addr)); } + +enum mmio_write_type { + mmio_write_type_b, + mmio_write_type_w, + mmio_write_type_l, +}; + +struct undo_mmio_write_data { + void *addr; + int reg; + enum mmio_write_type type; + union { + uint8_t bdata; + uint16_t wdata; + uint32_t ldata; + }; +}; + +void undo_mmio_write(void *p) +{ + struct undo_mmio_write_data *data = p; + msg_pdbg("Restoring MMIO space at %p\n", data->addr); + switch (data->type) { + case mmio_write_type_b: + mmio_writeb(data->bdata, data->addr); + break; + case mmio_write_type_w: + mmio_writew(data->wdata, data->addr); + break; + case mmio_write_type_l: + mmio_writel(data->ldata, data->addr); + break; + } + /* p was allocated in register_undo_mmio_write. */ + free(p); +} + +#define register_undo_mmio_write(a, c) \ +{ \ + struct undo_mmio_write_data *undo_mmio_write_data; \ + undo_mmio_write_data = malloc(sizeof(struct undo_mmio_write_data)); \ + undo_mmio_write_data->addr = a; \ + undo_mmio_write_data->type = mmio_write_type_##c; \ + undo_mmio_write_data->c##data = mmio_read##c(a); \ + register_shutdown(undo_mmio_write, undo_mmio_write_data); \ +} + +#define register_undo_mmio_writeb(a) register_undo_mmio_write(a, b) +#define register_undo_mmio_writew(a) register_undo_mmio_write(a, w) +#define register_undo_mmio_writel(a) register_undo_mmio_write(a, l) + +void rmmio_writeb(uint8_t val, void *addr) +{ + register_undo_mmio_writeb(addr); + mmio_writeb(val, addr); +} + +void rmmio_writew(uint16_t val, void *addr) +{ + register_undo_mmio_writew(addr); + mmio_writew(val, addr); +} + +void rmmio_writel(uint32_t val, void *addr) +{ + register_undo_mmio_writel(addr); + mmio_writel(val, addr); +} + +void rmmio_le_writeb(uint8_t val, void *addr) +{ + register_undo_mmio_writeb(addr); + mmio_le_writeb(val, addr); +} + +void rmmio_le_writew(uint16_t val, void *addr) +{ + register_undo_mmio_writew(addr); + mmio_le_writew(val, addr); +} + +void rmmio_le_writel(uint32_t val, void *addr) +{ + register_undo_mmio_writel(addr); + mmio_le_writel(val, addr); +} + +void rmmio_valb(void *addr) +{ + register_undo_mmio_writeb(addr); +} + +void rmmio_valw(void *addr) +{ + register_undo_mmio_writew(addr); +} + +void rmmio_vall(void *addr) +{ + register_undo_mmio_writel(addr); +} Modified: trunk/ichspi.c ============================================================================== --- trunk/ichspi.c Sat Apr 30 01:53:09 2011 (r1291) +++ trunk/ichspi.c Tue May 3 23:49:41 2011 (r1292) @@ -163,7 +163,7 @@ static int find_opcode(OPCODES *op, uint8_t opcode); static int find_preop(OPCODES *op, uint8_t preop); static int generate_opcodes(OPCODES * op); -static int program_opcodes(OPCODES * op); +static int program_opcodes(OPCODES *op, int enable_undo); static int run_opcode(OPCODE op, uint32_t offset, uint8_t datalength, uint8_t * data); @@ -269,7 +269,7 @@ int oppos=2; // use original JEDEC_BE_D8 offset curopcodes->opcode[oppos].opcode = opcode; curopcodes->opcode[oppos].spi_type = spi_type; - program_opcodes(curopcodes); + program_opcodes(curopcodes, 0); oppos = find_opcode(curopcodes, opcode); msg_pdbg ("on-the-fly OPCODE (0x%02X) re-programmed, op-pos=%d\n", opcode, oppos); return oppos; @@ -357,7 +357,7 @@ return 0; } -int program_opcodes(OPCODES * op) +static int program_opcodes(OPCODES *op, int enable_undo) { uint8_t a; uint16_t preop, optype; @@ -391,16 +391,30 @@ switch (spi_controller) { case SPI_CONTROLLER_ICH7: case SPI_CONTROLLER_VIA: - REGWRITE16(ICH7_REG_PREOP, preop); - REGWRITE16(ICH7_REG_OPTYPE, optype); - REGWRITE32(ICH7_REG_OPMENU, opmenu[0]); - REGWRITE32(ICH7_REG_OPMENU + 4, opmenu[1]); + /* Register undo only for enable_undo=1, i.e. first call. */ + if (enable_undo) { + rmmio_valw(ich_spibar + ICH7_REG_PREOP); + rmmio_valw(ich_spibar + ICH7_REG_OPTYPE); + rmmio_vall(ich_spibar + ICH7_REG_OPMENU); + rmmio_vall(ich_spibar + ICH7_REG_OPMENU + 4); + } + mmio_writew(preop, ich_spibar + ICH7_REG_PREOP); + mmio_writew(optype, ich_spibar + ICH7_REG_OPTYPE); + mmio_writel(opmenu[0], ich_spibar + ICH7_REG_OPMENU); + mmio_writel(opmenu[1], ich_spibar + ICH7_REG_OPMENU + 4); break; case SPI_CONTROLLER_ICH9: - REGWRITE16(ICH9_REG_PREOP, preop); - REGWRITE16(ICH9_REG_OPTYPE, optype); - REGWRITE32(ICH9_REG_OPMENU, opmenu[0]); - REGWRITE32(ICH9_REG_OPMENU + 4, opmenu[1]); + /* Register undo only for enable_undo=1, i.e. first call. */ + if (enable_undo) { + rmmio_valw(ich_spibar + ICH9_REG_PREOP); + rmmio_valw(ich_spibar + ICH9_REG_OPTYPE); + rmmio_vall(ich_spibar + ICH9_REG_OPMENU); + rmmio_vall(ich_spibar + ICH9_REG_OPMENU + 4); + } + mmio_writew(preop, ich_spibar + ICH9_REG_PREOP); + mmio_writew(optype, ich_spibar + ICH9_REG_OPTYPE); + mmio_writel(opmenu[0], ich_spibar + ICH9_REG_OPMENU); + mmio_writel(opmenu[1], ich_spibar + ICH9_REG_OPMENU + 4); break; default: msg_perr("%s: unsupported chipset\n", __func__); @@ -426,9 +440,11 @@ msg_pdbg("Reserved bits in BBAR not zero: 0x%04x", ichspi_bbar); ichspi_bbar |= minaddr; - mmio_writel(ichspi_bbar, ich_spibar + 0x50); + rmmio_writel(ichspi_bbar, ich_spibar + 0x50); ichspi_bbar = mmio_readl(ich_spibar + 0x50); - /* We don't have any option except complaining. */ + /* We don't have any option except complaining. And if the write + * failed, the restore will fail as well, so no problem there. + */ if (ichspi_bbar != minaddr) msg_perr("Setting BBAR failed!\n"); break; @@ -438,9 +454,11 @@ msg_pdbg("Reserved bits in BBAR not zero: 0x%04x", ichspi_bbar); ichspi_bbar |= minaddr; - mmio_writel(ichspi_bbar, ich_spibar + 0xA0); + rmmio_writel(ichspi_bbar, ich_spibar + 0xA0); ichspi_bbar = mmio_readl(ich_spibar + 0xA0); - /* We don't have any option except complaining. */ + /* We don't have any option except complaining. And if the write + * failed, the restore will fail as well, so no problem there. + */ if (ichspi_bbar != minaddr) msg_perr("Setting BBAR failed!\n"); break; @@ -470,7 +488,7 @@ } else { msg_pdbg("Programming OPCODES... "); curopcodes_done = &O_ST_M25P; - rc = program_opcodes(curopcodes_done); + rc = program_opcodes(curopcodes_done, 1); /* Technically not part of opcode init, but it allows opcodes * to run without transaction errors by setting the lowest * allowed address to zero. Modified: trunk/nicintel_spi.c ============================================================================== --- trunk/nicintel_spi.c Sat Apr 30 01:53:09 2011 (r1291) +++ trunk/nicintel_spi.c Tue May 3 23:49:41 2011 (r1292) @@ -148,6 +148,11 @@ nicintel_spibar = physmap("Intel Gigabit NIC w/ SPI flash", io_base_addr, 4096); + /* Automatic restore of EECD on shutdown is not possible because EECD + * does not only contain FLASH_WRITES_DISABLED|FLASH_WRITES_ENABLED, + * but other bits with side effects as well. Those other bits must be + * left untouched. + */ tmp = pci_mmio_readl(nicintel_spibar + EECD); tmp &= ~FLASH_WRITES_DISABLED; tmp |= FLASH_WRITES_ENABLED; @@ -167,6 +172,9 @@ { uint32_t tmp; + /* Disable writes manually. See the comment about EECD in + * nicintel_spi_init() for details. + */ tmp = pci_mmio_readl(nicintel_spibar + EECD); tmp &= ~FLASH_WRITES_ENABLED; tmp |= FLASH_WRITES_DISABLED; Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Sat Apr 30 01:53:09 2011 (r1291) +++ trunk/programmer.h Tue May 3 23:49:41 2011 (r1292) @@ -316,6 +316,18 @@ #define pci_mmio_readb mmio_le_readb #define pci_mmio_readw mmio_le_readw #define pci_mmio_readl mmio_le_readl +void rmmio_writeb(uint8_t val, void *addr); +void rmmio_writew(uint16_t val, void *addr); +void rmmio_writel(uint32_t val, void *addr); +void rmmio_le_writeb(uint8_t val, void *addr); +void rmmio_le_writew(uint16_t val, void *addr); +void rmmio_le_writel(uint32_t val, void *addr); +#define pci_rmmio_writeb rmmio_le_writeb +#define pci_rmmio_writew rmmio_le_writew +#define pci_rmmio_writel rmmio_le_writel +void rmmio_valb(void *addr); +void rmmio_valw(void *addr); +void rmmio_vall(void *addr); /* programmer.c */ int noop_shutdown(void); Modified: trunk/satamv.c ============================================================================== --- trunk/satamv.c Sat Apr 30 01:53:09 2011 (r1291) +++ trunk/satamv.c Tue May 3 23:49:41 2011 (r1292) @@ -102,8 +102,7 @@ msg_pspew("BAR2Sz=0x%01x\n", (tmp >> 19) & 0x7); tmp &= 0xffffffc0; tmp |= 0x0000001f; - /* FIXME: This needs to be an auto-reversible write. */ - pci_mmio_writel(tmp, mv_bar + PCI_BAR2_CONTROL); + pci_rmmio_writel(tmp, mv_bar + PCI_BAR2_CONTROL); /* Enable flash: GPIO Port Control Register 0x104f0 */ tmp = pci_mmio_readl(mv_bar + GPIO_PORT_CONTROL); @@ -114,8 +113,7 @@ "values!\n"); tmp &= 0xfffffffc; tmp |= 0x2; - /* FIXME: This needs to be an auto-reversible write. */ - pci_mmio_writel(tmp, mv_bar + GPIO_PORT_CONTROL); + pci_rmmio_writel(tmp, mv_bar + GPIO_PORT_CONTROL); /* Get I/O BAR location. */ tmp = pci_read_long(pcidev_dev, PCI_BASE_ADDRESS_2) &

1 0

RIVA TNT2 Model 64/Model 64 Pro
by Benjamin Henrion 03 May '11

03 May '11

Hi, I own such a card: RIVA TNT2 Model 64/Model 64 Pro http://www.zoobab.com/flashrom-tnt2-m64 Which is listed by the flashrom wiki as a working programmer. Any idea how to connect a DIP32 over this card? There is a Holtek Eeprom on it, and I would like to know if I could flash LPC chips with (the bus type seems to be CHIP_BUSTYPE_PARALLEL). Any idea? Best, -- Benjamin Henrion <bhenrion at ffii.org> FFII Brussels - +32-484-566109 - +32-2-4148403 "In July 2005, after several failed attempts to legalise software patents in Europe, the patent establishment changed its strategy. Instead of explicitly seeking to sanction the patentability of software, they are now seeking to create a central European patent court, which would establish and enforce patentability rules in their favor, without any possibility of correction by competing courts or democratically elected legislators."

1 0

Re: [flashrom] [PATCH 2/6] some additional comments for ichspi.c
by Michael Karcher 03 May '11

03 May '11

Am Freitag, den 01.04.2011, 14:33 +0200 schrieb Stefan Tauner: > - uint8_t atomic; //Use preop: (0: none, 1: preop0, 2: preop1 > + uint8_t atomic; //Use preop: (0: none, 1: preop0 only, 2: both) Nack. The ICH10 data sheet is explicit on SPOP selecting "one of the two programmed prefix opcodes". So 2 does not mean both, but preop1. Regards, Michael Karcher

2 1

Supermicro X8DTU-F
by Jimmie Tauriainen 02 May '11

02 May '11

-- Jimmie Tauriainen South Pole AB Phone: +46 8 56237100 Anderstorpsvägen 16 Mobile: +46 707 777651 SE - 17154 Solna e-mail: jimmie(a)southpole.se www.southpole.se

1 0

Re: [flashrom] GigaByte GA-K8NS
by Denis S. Soldatov 02 May '11

02 May '11

В Сб., 30/04/2011 в 14:27 +0200, Stefan Tauner пишет: > hey > > you quit irc yesterday... so i fear that you have tried to reboot > although we warned you multiply times. > we would like to hear from you again in any case to know what happened > and to be able to try the patch we have created for you. > Hi, Thanks for your support today can not, but tomorrow will try as soon as the time and immediately accomplish your goal in the channel irc

1 0

here's the now completely fixed patch.
by Brandon Dowdy 01 May '11

01 May '11

I think this patch is fixed now.

1 0

Gigabyte M68M-S2P Support
by Sascha Conradi 01 May '11

01 May '11

Hi.. I call for support for Gigabyte M68M-S2P thanks..

1 0

Flash Marvell 91xx Config PROM
by PETER ANDERSON 30 Apr '11

30 Apr '11

Hi, I have a Asus motherboard (p7p55d-e pro) with (I believe) an onboard Marvell 9120 Sata 3 controller. I also have an add on card Sata controller with a Marvell 9123 chip. When I updated my firmware, both devices were found and updated but upon reboot the "on board" Marvell Controller is bricked. It no longer appears in the boot up/bios sequence. I'm looking for a way to flash the chip back preferably in circuit. Is this something flashrom can do? The Marvell Flash device is macronix MX25L4005A. Thanks, Pete I'm pretty sure this is the controller that's not responding 0a:00.1 IDE interface [0101]: Device [1b4b:91a4] (rev 11) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Device [1b4b:91a4] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 16 Region 0: I/O ports at dc00 [size=8] Region 1: I/O ports at d880 [size=4] Region 2: I/O ports at d800 [size=8] Region 3: I/O ports at d480 [size=4] Region 4: I/O ports at d400 [size=16] Region 5: Memory at f7effc00 (32-bit, non-prefetchable) [size=16] Expansion ROM at f7ee0000 [disabled] [size=64K] Capabilities: <access denied> 00: 4b 1b a4 91 03 01 10 00 11 8f 01 01 08 00 80 00 10: 01 dc 00 00 81 d8 00 00 01 d8 00 00 81 d4 00 00 20: 01 d4 00 00 00 fc ef f7 00 00 00 00 4b 1b a4 91 30: 00 00 ee f7 40 00 00 00 00 00 00 00 0a 02 00 0

1 0

FAILED: motherboard update bios fail (gigabyte-X58A-UD3R (rev. 2.0))
by healthly 30 Apr '11

30 Apr '11

Dear flashrom, I use flashrom to update bios under centos5.5.then there is following output(please help me!) : flashrom v0.9.3-r1288 on Linux 2.6.18-194.26.1.el5xen (x86_64), built with libpci 2.2.3, GCC 4.1.2 20080704 (Red Hat 4.1.2-48), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1414M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 999 us, 10000 myus = 9991 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "X58A-UD3R" DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "X58A-UD3R" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8720. Found chipset "Intel ICH10R", enabling flash write... chipset PCI ID is 8086:3a16, 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x4 0x7fffffff/0x7fffffff FWH IDSEL: 0x5 0x7fffffff/0x7fffffff FWH IDSEL: 0x6 0x7fffffff/0x7fffffff FWH IDSEL: 0x7 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0x464: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x0000 (HSFS) FLOCKDN 0, FDV 0, FDOPSS 0, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00001fff (FREG0: Flash Descriptor) Flash Descriptor region is unused. 0x58: 0x00001fff (FREG1: BIOS) BIOS region is unused. 0x5C: 0x00001fff (FREG2: Management Engine) Management Engine region is unused. 0x60: 0x00001fff (FREG3: Gigabit Ethernet) Gigabit Ethernet region is unused. 0x64: 0x00001fff (FREG4: Platform Data) Platform Data region is unused. 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x04 (SSFS) AEL 0, FCERR 0, FDONE 1, SCIP 0 0x91: 0x007f10 (SSFC) 0x94: 0x5006 (PREOP) 0x96: 0x462b (OPTYPE) 0x98: 0x05ab0302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. No IT87* serial flash segment enabled. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV001BB, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV001BT, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV002BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV002BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV004BB, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV004BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV008BB, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV008BT, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L05PT, 64 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L05PU, 64 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PT, 128 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PU, 128 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PT, 256 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PU, 256 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PT, 512 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PU, 512 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L80P, 1024 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PT, 2048 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PU, 2048 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L020, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L080, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L016, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L032, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25LQ032, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DQ161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Bright BM29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F25L008A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05T, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10T, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20T, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40T, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80T, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16T, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32T, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64T, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN29F010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address 0xffe00000. Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1635E, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL032A, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL064A, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF010.REMS, 128 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF064C, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF040.REMS, 512 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25LF040A.RES, 512 KB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 RES returned 0x14 0x14. probe_spi_res2: id1 0x14, id2 0x14 Probing for SST SST25VF040B.REMS, 512 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x27, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BB, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25Q80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040/P, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39L040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49F002U/N, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: probe_jedec_common: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Eon unknown Eon SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Not unmapping zero size at 0xffffffffffffffff Flash image seems to be a legacy BIOS. Disabling checks. Reading old flash chip contents... Erasing and writing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff:S, 0x001000-0x001fff:S, 0x002000-0x002fff:S, 0x003000-0x003fff:S, 0x004000-0x004fff:S, 0x005000-0x005fff:S, 0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S, 0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:S, 0x00c000-0x00cfff:S, 0x00d000-0x00dfff:S, 0x00e000-0x00efff:S, 0x00f000-0x00ffff:S, 0x010000-0x010fff:S, 0x011000-0x011fff:S, 0x012000-0x012fff:S, 0x013000-0x013fff:S, 0x014000-0x014fff:S, 0x015000-0x015fff:S, 0x016000-0x016fff:S, 0x017000-0x017fff:S, 0x018000-0x018fff:S, 0x019000-0x019fff:S, 0x01a000-0x01afff:S, 0x01b000-0x01bfff:S, 0x01c000-0x01cfff:S, 0x01d000-0x01dfff:S, 0x01e000-0x01efff:S, 0x01f000-0x01ffff:S, 0x020000-0x020fff:S, 0x021000-0x021fff:S, 0x022000-0x022fff:S, 0x023000-0x023fff:S, 0x024000-0x024fff:S, 0x025000-0x025fff:S, 0x026000-0x026fff:S, 0x027000-0x027fff:S, 0x028000-0x028fff:S, 0x029000-0x029fff:S, 0x02a000-0x02afff:S, 0x02b000-0x02bfff:S, 0x02c000-0x02cfff:S, 0x02d000-0x02dfff:S, 0x02e000-0x02efff:S, 0x02f000-0x02ffff:S, 0x030000-0x030fff:S, 0x031000-0x031fff:S, 0x032000-0x032fff:S, 0x033000-0x033fff:S, 0x034000-0x034fff:S, 0x035000-0x035fff:S, 0x036000-0x036fff:S, 0x037000-0x037fff:S, 0x038000-0x038fff:S, 0x039000-0x039fff:S, 0x03a000-0x03afff:S, 0x03b000-0x03bfff:S, 0x03c000-0x03cfff:S, 0x03d000-0x03dfff:S, 0x03e000-0x03efff:S, 0x03f000-0x03ffff:S, 0x040000-0x040fff:S, 0x041000-0x041fff:S, 0x042000-0x042fff:S, 0x043000-0x043fff:S, 0x044000-0x044fff:S, 0x045000-0x045fff:S, 0x046000-0x046fff:S, 0x047000-0x047fff:S, 0x048000-0x048fff:S, 0x049000-0x049fff:S, 0x04a000-0x04afff:S, 0x04b000-0x04bfff:S, 0x04c000-0x04cfff:S, 0x04d000-0x04dfff:S, 0x04e000-0x04efff:S, 0x04f000-0x04ffff:S, 0x050000-0x050fff:S, 0x051000-0x051fff:S, 0x052000-0x052fff:S, 0x053000-0x053fff:S, 0x054000-0x054fff:S, 0x055000-0x055fff:S, 0x056000-0x056fff:S, 0x057000-0x057fff:S, 0x058000-0x058fff:S, 0x059000-0x059fff:S, 0x05a000-0x05afff:S, 0x05b000-0x05bfff:S, 0x05c000-0x05cfff:S, 0x05d000-0x05dfff:S, 0x05e000-0x05efff:S, 0x05f000-0x05ffff:S, 0x060000-0x060fff:S, 0x061000-0x061fff:S, 0x062000-0x062fff:S, 0x063000-0x063fff:S, 0x064000-0x064fff:S, 0x065000-0x065fff:S, 0x066000-0x066fff:S, 0x067000-0x067fff:S, 0x068000-0x068fff:S, 0x069000-0x069fff:S, 0x06a000-0x06afff:S, 0x06b000-0x06bfff:S, 0x06c000-0x06cfff:S, 0x06d000-0x06dfff:S, 0x06e000-0x06efff:S, 0x06f000-0x06ffff:S, 0x070000-0x070fff:S, 0x071000-0x071fff:S, 0x072000-0x072fff:S, 0x073000-0x073fff:S, 0x074000-0x074fff:S, 0x075000-0x075fff:S, 0x076000-0x076fff:S, 0x077000-0x077fff:S, 0x078000-0x078fff:S, 0x079000-0x079fff:S, 0x07a000-0x07afff:S, 0x07b000-0x07bfff:S, 0x07c000-0x07cfff:S, 0x07d000-0x07dfff:S, 0x07e000-0x07efff:S, 0x07f000-0x07ffff:S, 0x080000-0x080fff:W, 0x081000-0x081fff:W, 0x082000-0x082fff:W, 0x083000-0x083fff:W, 0x084000-0x084fff:W, 0x085000-0x085fff:W, 0x086000-0x086fff:W, 0x087000-0x087fff:W, 0x088000-0x088fff:W, 0x089000-0x089fff:W, 0x08a000-0x08afff:W, 0x08b000-0x08bfff:W, 0x08c000-0x08cfff:W, 0x08d000-0x08dfff:W, 0x08e000-0x08efff:W, 0x08f000-0x08ffff:W, 0x090000-0x090fff:W, 0x091000-0x091fff:W, 0x092000-0x092fff:W, 0x093000-0x093fff:W, 0x094000-0x094fff:W, 0x095000-0x095fff:W, 0x096000-0x096fff:W, 0x097000-0x097fff:W, 0x098000-0x098fff:W, 0x099000-0x099fff:W, 0x09a000-0x09afff:W, 0x09b000-0x09bfff:W, 0x09c000-0x09cfff:W, 0x09d000-0x09dfff:W, 0x09e000-0x09efff:W, 0x09f000-0x09ffff:W, 0x0a0000-0x0a0fff:W, 0x0a1000-0x0a1fff:W, 0x0a2000-0x0a2fff:W, 0x0a3000-0x0a3fff:W, 0x0a4000-0x0a4fff:W, 0x0a5000-0x0a5fff:W, 0x0a6000-0x0a6fff:W, 0x0a7000-0x0a7fff:W, 0x0a8000-0x0a8fff:W, 0x0a9000-0x0a9fff:W, 0x0aa000-0x0aafff:W, 0x0ab000-0x0abfff:W, 0x0ac000-0x0acfff:W, 0x0ad000-0x0adfff:W, 0x0ae000-0x0aefff:W, 0x0af000-0x0affff:W, 0x0b0000-0x0b0fff:W, 0x0b1000-0x0b1fff:W, 0x0b2000-0x0b2fff:W, 0x0b3000-0x0b3fff:W, 0x0b4000-0x0b4fff:W, 0x0b5000-0x0b5fff:W, 0x0b6000-0x0b6fff:W, 0x0b7000-0x0b7fff:W, 0x0b8000-0x0b8fff:W, 0x0b9000-0x0b9fff:W, 0x0ba000-0x0bafff:W, 0x0bb000-0x0bbfff:W, 0x0bc000-0x0bcfff:W, 0x0bd000-0x0bdfff:W, 0x0be000-0x0befff:W, 0x0bf000-0x0bffff:W, 0x0c0000-0x0c0fff:W, 0x0c1000-0x0c1fff:W, 0x0c2000-0x0c2fff:W, 0x0c3000-0x0c3fff:W, 0x0c4000-0x0c4fff:W, 0x0c5000-0x0c5fff:W, 0x0c6000-0x0c6fff:W, 0x0c7000-0x0c7fff:W, 0x0c8000-0x0c8fff:W, 0x0c9000-0x0c9fff:W, 0x0ca000-0x0cafff:W, 0x0cb000-0x0cbfff:W, 0x0cc000-0x0ccfff:W, 0x0cd000-0x0cdfff:W, 0x0ce000-0x0cefff:W, 0x0cf000-0x0cffff:W, 0x0d0000-0x0d0fff:W, 0x0d1000-0x0d1fff:W, 0x0d2000-0x0d2fff:W, 0x0d3000-0x0d3fff:W, 0x0d4000-0x0d4fff:W, 0x0d5000-0x0d5fff:W, 0x0d6000-0x0d6fff:W, 0x0d7000-0x0d7fff:W, 0x0d8000-0x0d8fff:W, 0x0d9000-0x0d9fff:W, 0x0da000-0x0dafff:W, 0x0db000-0x0dbfff:W, 0x0dc000-0x0dcfff:W, 0x0dd000-0x0ddfff:W, 0x0de000-0x0defff:W, 0x0df000-0x0dffff:W, 0x0e0000-0x0e0fff:W, 0x0e1000-0x0e1fff:W, 0x0e2000-0x0e2fff:W, 0x0e3000-0x0e3fff:W, 0x0e4000-0x0e4fff:W, 0x0e5000-0x0e5fff:W, 0x0e6000-0x0e6fff:W, 0x0e7000-0x0e7fff:W, 0x0e8000-0x0e8fff:W, 0x0e9000-0x0e9fff:W, 0x0ea000-0x0eafff:W, 0x0eb000-0x0ebfff:W, 0x0ec000-0x0ecfff:W, 0x0ed000-0x0edfff:W, 0x0ee000-0x0eefff:W, 0x0ef000-0x0effff:W, 0x0f0000-0x0f0fff:W, 0x0f1000-0x0f1fff:W, 0x0f2000-0x0f2fff:W, 0x0f3000-0x0f3fff:W, 0x0f4000-0x0f4fff:W, 0x0f5000-0x0f5fff:W, 0x0f6000-0x0f6fff:W, 0x0f7000-0x0f7fff:W, 0x0f8000-0x0f8fff:W, 0x0f9000-0x0f9fff:W, 0x0fa000-0x0fafff:W, 0x0fb000-0x0fbfff:W, 0x0fc000-0x0fcfff:W, 0x0fd000-0x0fdfff:W, 0x0fe000-0x0fefff:W, 0x0ff000-0x0fffff:E program_opcodes: preop=5006 optype=463b opmenu=05200302c79f0190 on-the-fly OPCODE (0x20) re-programmed, op-pos=2 W, 0x100000-0x100fff:EW, 0x101000-0x101fff:EW, 0x102000-0x102fff:EW, 0x103000-0x103fff:EW, 0x104000-0x104fff:EW, 0x105000-0x105fff:EW, 0x106000-0x106fff:EW, 0x107000-0x107fff:EW, 0x108000-0x108fff:EW, 0x109000-0x109fff:EW, 0x10a000-0x10afff:EW, 0x10b000-0x10bfff:Etimeout, ICH9_REG_SSFS=0x00002401 run OPCODE 0x20 failed spi_block_erase_20 failed during command execution at address 0x10b000 Looking at blockwise erase function 1... trying... 0x000000-0x00ffff:S, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:S, 0x050000-0x05ffff:S, 0x060000-0x06ffff:S, 0x070000-0x07ffff:S, 0x080000-0x08ffff:S, 0x090000-0x09ffff:S, 0x0a0000-0x0affff:S, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:S, 0x0e0000-0x0effff:S, 0x0f0000-0x0fffff:S, 0x100000-0x10ffff:E program_opcodes: preop=5006 optype=463b opmenu=05520302c79f0190 on-the-fly OPCODE (0x52) re-programmed, op-pos=2 ERASE FAILED at 0x00100000! Expected=0xff, Read=0x11, failed byte count from 0x00100000-0x0010ffff: 0xeea9 ERASE FAILED! Looking at blockwise erase function 2... trying... 0x000000-0x00ffff:S, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:S, 0x050000-0x05ffff:S, 0x060000-0x06ffff:S, 0x070000-0x07ffff:S, 0x080000-0x08ffff:S, 0x090000-0x09ffff:S, 0x0a0000-0x0affff:S, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:S, 0x0e0000-0x0effff:S, 0x0f0000-0x0fffff:S, 0x100000-0x10ffff:E program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 on-the-fly OPCODE (0xD8) re-programmed, op-pos=2 timeout, ICH9_REG_SSFS=0x00002401 run OPCODE 0xd8 failed spi_block_erase_d8 failed during command execution at address 0x100000 Error: SCIP never cleared! run OPCODE 0x03 failed Can't read anymore! FAILED! Uh oh. Erase/write failed. Checking if anything changed. Error: SCIP never cleared! run OPCODE 0x03 failed Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! Restoring PCI config space for 00:1f:0 reg 0xdc please help me ,thankyou very much! Best ! healthly

2 2

MCP61:flashrom -V SPI
by Rianav Antares 30 Apr '11

30 Apr '11

Hello, I hope you find this useful. This is after following the instructions given in flashrom -V on my mcp61P nforce430 msi k9n6pgm2 . Cheers. [root@verian ~]# flashrom -V flashrom v0.9.3-r1205 on Linux 2.6.38-ARCH (i686), built with libpci 3.1.7, GCC 4.5.2 20110127 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1443M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 1000 us, 10000 myus = 9993 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MSI" DMI string system-product-name: "MS-7309" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "MSI" DMI string baseboard-product-name: "MS-7309" DMI string baseboard-version: "1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61", enabling flash write... chipset PCI ID is 10de:03e0, This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xd0000000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. This chipset supports the following protocols: LPC. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: skipped. Probing for AMIC A25L05PU, 64 KB: skipped. Probing for AMIC A25L10PT, 128 KB: skipped. Probing for AMIC A25L10PU, 128 KB: skipped. Probing for AMIC A25L20PT, 256 KB: skipped. Probing for AMIC A25L20PU, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A25L80P, 1024 KB: skipped. Probing for AMIC A25L16PT, 2048 KB: skipped. Probing for AMIC A25L16PU, 2048 KB: skipped. Probing for AMIC A25L512, 64 KB: skipped. Probing for AMIC A25L010, 128 KB: skipped. Probing for AMIC A25L020, 256 KB: skipped. Probing for AMIC A25L040, 512 KB: skipped. Probing for AMIC A25L080, 1024 KB: skipped. Probing for AMIC A25L016, 2048 KB: skipped. Probing for AMIC A25L032, 4096 KB: skipped. Probing for AMIC A25LQ032, 4096 KB: skipped. Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF081A, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25DQ161, 2048 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for Bright BM29F040, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Hyundai HY29F040A, 512 KB: skipped. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: skipped. Probing for Intel 82802AC, 1024 KB: skipped. Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L1635E, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29F040, 512 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xd7, id2 0xde, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: skipped. Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF064C, 8192 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25LF040A.RES, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: skipped. Probing for SST SST49LF003A/B, 384 KB: skipped. Probing for SST SST49LF004A/B, 512 KB: skipped. Probing for SST SST49LF004C, 512 KB: skipped. Probing for SST SST49LF008A, 1024 KB: skipped. Probing for SST SST49LF008C, 1024 KB: skipped. Probing for SST SST49LF016C, 2048 KB: skipped. Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xd7, id2 0xde, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xd7, id2 0xde, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M25PX32, 4096 KB: skipped. Probing for ST M25PX64, 8192 KB: skipped. Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: skipped. Probing for ST M50FW016, 2048 KB: skipped. Probing for ST M50FW040, 512 KB: skipped. Probing for ST M50FW080, 1024 KB: skipped. Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25Q64, 8192 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Probing for Winbond W29C040/P, 512 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040(F)B, 512 KB: probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040(F)C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x08, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: skipped. Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xd7, id2 0xde, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: skipped. Probing for Winbond W39V080FA, 1024 KB: skipped. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Probing for AMIC unknown AMIC SPI chip, 0 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for Eon unknown Eon SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. [root@verian ~]# lspci -nnvvvxxx 00:00.0 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller [10de:03ea] (rev a1) Subsystem: nVidia Corporation Device [10de:cb84] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=17 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 400MHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 ea 03 06 00 b0 00 a1 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 84 cb 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 40: de 10 84 cb 08 dc 20 02 20 00 11 11 d0 00 00 00 50: 23 02 7f 00 03 00 00 00 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 00 00 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00 80: 23 99 88 00 fa 00 64 0d 03 00 00 00 7f 00 00 00 90: 70 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8 e0: 00 00 e0 fe 00 00 00 00 06 00 00 00 20 10 00 00 f0: f0 ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00:01.0 ISA bridge [0601]: nVidia Corporation MCP61 LPC Bridge [10de:03e0] (rev a2) Subsystem: nVidia Corporation Device [10de:cb84] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: I/O ports at 4f00 [size=256] 00: de 10 e0 03 0f 00 a0 00 a2 00 01 06 00 00 80 00 10: 01 4f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 84 cb 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: de 10 84 cb 00 00 ff fe fa 3e ff 00 fa 3e ff 00 50: fa 3e ff 00 00 5a 62 02 00 00 00 05 2f 00 fc 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 70: 10 00 ff ff c5 80 00 00 00 00 04 19 00 00 00 c0 80: 09 d0 00 10 08 12 00 00 ff 00 00 01 ff 00 00 00 90: ff 7f 00 00 00 00 00 00 21 65 08 74 b9 0c 00 d0 a0: 00 00 10 80 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 0a 7f 0a 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:01.1 SMBus [0c05]: nVidia Corporation MCP61 SMBus [10de:03eb] (rev a2) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 4900 [size=64] Region 4: I/O ports at 4d00 [size=64] Region 5: I/O ports at 4e00 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00: de 10 eb 03 01 00 b0 00 a2 00 05 0c 00 00 80 00 10: 01 49 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 4d 00 00 01 4e 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 00 00 40: 62 14 09 73 01 00 02 c0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 40 00 00 01 44 00 00 01 48 00 00 00 10 d0 fe 70: 00 00 00 00 00 00 00 d0 00 00 fe fe 01 4c 00 00 80: 00 10 fe fe 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: d4 30 80 01 01 00 00 00 00 00 00 00 00 00 00 00 d0: 4c 00 40 01 10 00 00 00 05 00 00 00 00 00 00 00 e0: 88 10 04 00 00 40 02 07 80 22 04 20 41 44 44 11 f0: 02 ff 1e bf 01 00 00 80 10 00 00 00 00 00 00 00 00:01.2 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller [10de:03f5] (rev a2) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 f5 03 00 04 a0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 10 02 80 10 10 00 10 10 50: 10 10 10 10 00 00 00 00 00 00 00 00 10 42 00 00 60: 0b 00 00 00 c0 1c 52 06 21 00 10 0a 00 00 63 00 70: 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 40 00 00 00 00 00 a0 18 00 00 90: 00 00 00 00 00 00 00 12 20 81 04 00 00 00 00 00 a0: 00 14 00 06 00 00 00 00 00 00 00 00 01 00 00 00 b0: 00 00 00 00 42 80 30 04 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:01.3 Co-processor [0b40]: nVidia Corporation MCP61 SMU [10de:03f4] (rev a2) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 5 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=512K] 00: de 10 f4 03 06 00 a0 00 a2 00 40 0b 00 00 80 00 10: 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 03 01 40: 62 14 09 73 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 d0 00 00 00 00 00 00 00 00 80: 05 9c 80 01 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 02 a8 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.0 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller [10de:03f1] (rev a3) (prog-if 10 [OHCI]) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 20 Region 0: Memory at dbf7f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00: de 10 f1 03 07 00 b0 00 a3 10 03 0c 00 00 80 00 10: 00 f0 f7 db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 07 01 03 01 40: 62 14 09 73 01 00 02 fe 00 00 00 00 00 00 00 00 50: 01 00 00 00 1d 47 40 00 10 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.1 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller [10de:03f2] (rev a3) (prog-if 20 [EHCI]) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 21 Region 0: Memory at dbf7ec00 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00: de 10 f2 03 06 00 b0 00 a3 20 03 0c 00 00 80 00 10: 00 ec f7 db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 02 03 01 40: 62 14 09 73 0a 80 98 20 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 01 00 00 60 18 85 c3 13 0f 01 00 00 00 00 70: 00 00 08 00 00 10 20 80 89 3d b6 22 77 25 d4 00 80: 01 00 02 fe 00 80 00 00 00 00 00 00 15 16 00 00 90: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 01 00 00 08 e0 00 00 00 00 00 00 00 00 b0: 00 11 22 33 44 00 00 00 ff 03 00 00 00 00 00 00 c0: 10 10 2d 0d 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:04.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI bridge [10de:03f3] (rev a1) (prog-if 01 [Subtractive decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: [b8] Subsystem: nVidia Corporation Device [10de:cb84] Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 00: de 10 f3 03 04 00 b0 00 a1 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 80 22 20: f0 ff 00 00 f0 ff 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 b8 00 00 00 00 00 00 00 00 00 02 02 40: 00 00 73 07 01 00 02 00 07 00 00 00 00 00 48 00 50: 00 00 00 00 00 00 00 00 ff 1f ff 1f 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 03 00 00 fa ff 00 00 00 00 00 00 08 00 00 a8 90: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00 a0: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 ff ff 00 00 0d 8c 00 00 de 10 84 cb c0: de 10 84 cb 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:05.0 Audio device [0403]: nVidia Corporation MCP61 High Definition Audio [10de:03f0] (rev a2) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin B routed to IRQ 23 Region 0: Memory at dbf78000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: oss_hdaudio 00: de 10 f0 03 06 00 b0 00 a2 00 03 04 00 00 80 00 10: 00 80 f7 db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 02 05 40: 62 14 09 73 01 50 02 c0 00 00 00 00 01 01 0f 00 50: 05 6c 80 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 02 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 47 00 29 00 00 00 00 00 00 00:06.0 IDE interface [0101]: nVidia Corporation MCP61 IDE [10de:03ec] (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: nVidia Corporation Device [10de:cb84] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at fff0 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_amd Kernel modules: amd74xx, pata_amd 00: de 10 ec 03 05 00 b0 00 a2 8a 01 01 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: f1 ff 00 00 00 00 00 00 00 00 00 00 de 10 84 cb 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01 40: de 10 84 cb 01 00 02 00 00 00 00 00 00 00 00 00 50: 02 f0 00 00 00 00 00 00 99 99 99 99 aa 00 a8 a8 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 01 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 43 Region 0: Memory at dbf7d000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at de00 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit+ Address: 00000000fee0300c Data: 4179 Masking: 000000fe Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: forcedeth Kernel modules: forcedeth 00: de 10 ef 03 07 04 b0 00 a2 00 80 06 00 00 00 00 10: 00 d0 f7 db 01 de 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 01 14 40: 62 14 09 73 01 50 02 fe 00 01 00 00 08 00 00 20 50: 05 6c 87 01 0c 30 e0 fe 00 00 00 00 79 41 00 00 60: fe 00 00 00 00 00 00 00 ff 00 00 00 08 00 02 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 42 01 00 00 00 00 00 00 00:08.0 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller [10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Micro-Star International Co., Ltd. Device [1462:7309] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at dd80 [size=8] Region 1: I/O ports at dd00 [size=4] Region 2: I/O ports at dc00 [size=8] Region 3: I/O ports at db80 [size=4] Region 4: I/O ports at db00 [size=16] Region 5: Memory at dbf7c000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv Kernel modules: sata_nv 00: de 10 f6 03 07 00 b0 00 a2 85 01 01 00 00 80 00 10: 81 dd 00 00 01 dd 00 00 01 dc 00 00 81 db 00 00 20: 01 db 00 00 00 c0 f7 db 00 00 00 00 62 14 09 73 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01 40: 62 14 09 73 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0f 68 08 00 00 00 00 00 00 20 00 20 44 20 00 20 60: 00 c6 00 c7 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 81 80: 00 00 00 c0 00 f0 8f a9 00 00 08 80 00 50 9c 8f 90: 00 00 10 90 00 00 00 00 06 00 06 10 f6 03 01 01 a0: 08 00 00 0f 00 00 00 00 00 00 00 00 33 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8 d0: 09 00 00 49 00 08 03 00 09 00 00 49 00 08 03 00 e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00:09.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e8] (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: dc000000-dfffffff Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4129 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #1, PowerLimit 75.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00: de 10 e8 03 07 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 e1 e1 00 00 20: 00 dc f0 df 01 c0 f1 cf 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 1a 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 29 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 01 3d 11 00 90: 40 00 01 31 80 25 08 00 c0 01 48 01 08 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0b.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e9] (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4141 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00: de 10 e9 03 04 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 41 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 11 3c 11 01 90: 00 00 11 10 00 05 10 00 c0 01 00 00 08 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0c.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e9] (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4149 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #3, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00: de 10 e9 03 04 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 04 04 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 49 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 11 3c 11 02 90: 00 00 11 10 00 05 18 00 c0 01 00 00 08 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: 400MHz Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- 00: 22 10 00 12 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00 50: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00 60: 00 00 01 00 e0 00 00 00 20 a8 4e 00 20 f8 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 00 01 21 20 20 11 11 60 02 f5 8f 13 00 00 00 90: 92 02 85 04 00 00 00 00 07 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 bf 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 03 00 e0 00 80 ff ef 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 03 0a 00 00 00 0b 00 00 03 00 c0 00 00 0b fe 00 c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 03 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 00 00 00 01 01 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: e0 3e 78 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 06 00 48 0d 00 00 00 00 80: 05 00 00 00 00 00 00 00 35 fb 7d 00 34 03 22 00 90: 10 00 01 00 0b 80 58 7f 07 03 00 80 00 00 00 00 a0: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: f5 1d 95 69 e6 00 00 00 73 64 bb 94 94 90 8c 88 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 38 2b 81 62 50 a4 9e ea 1e 07 60 40 ef cd a4 60 e0: 3c 09 c5 82 42 a4 d1 40 34 86 89 9c 2f a5 2c aa f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k10temp Kernel modules: k10temp 00: 22 10 03 12 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: ff ff ff 3f 5c 00 b0 4a 00 00 00 00 00 00 00 00 50: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 04 00 24 34 00 00 00 30 52 80 01 00 70: 53 11 04 00 11 11 08 00 14 0c 20 00 14 09 09 00 80: 81 87 00 e6 e6 41 e6 01 08 00 00 00 00 40 58 42 90: 00 00 00 00 42 6c 00 00 30 07 15 90 00 00 00 00 a0: 00 09 02 90 80 18 68 22 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 24 0f 81 c8 16 10 22 03 26 53 27 00 e0: 00 00 00 00 30 13 00 1e 79 1f 07 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 62 0f 10 00 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 04 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:00.0 VGA compatible controller [0300]: nVidia Corporation G96 [GeForce 9500 GT] [10de:0640] (rev a1) (prog-if 00 [VGA controller]) Subsystem: eVga.com. Corp. Device [3842:c958] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 19 Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at dc000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at ef80 [size=128] [virtual] Expansion ROM at def80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [128 v1] Power Budgeting <?> Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nvidia Kernel modules: nouveau, nvidiafb, nvidia 00: de 10 40 06 07 00 10 00 a1 00 00 03 00 00 00 00 10: 00 00 00 df 0c 00 00 c0 00 00 00 00 04 00 00 dc 20: 00 00 00 00 81 ef 00 00 00 00 00 00 42 38 58 c9 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00 40: 42 38 58 c9 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00 60: 01 68 03 00 00 00 00 00 05 78 80 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 10 b4 02 00 20 85 00 00 80: 10 29 00 00 01 4d 00 00 48 00 01 11 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00 a0: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 b0: 00 00 00 00 09 00 14 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [root@verian ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 02:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce 9500 GT] (rev a1) [root@verian ~]# -- Rianav Antares kerenskyy(a)myopera.com

1 0

Re: [flashrom] [PATCH] improve output in case run_opcode fails
by Michael Karcher 30 Apr '11

30 Apr '11

Am Samstag, den 30.04.2011, 01:30 +0200 schrieb Stefan Tauner: > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > + if ((opcode->spi_type == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || > + (opcode->spi_type == SPI_OPCODE_TYPE_WRITE_NO_ADDRESS)) { > + msg_pspew("The data was:\n"); > + int i; please don't declare variables after statements. > + for(i=0; i<count; i++){ > + msg_pspew("%3d: 0x%02x\n", i, data[i]); > + } > + } > } > > return result; Acked-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> moved "int i" one line up and committed in r1291 Regards, Michael Karcher

1 0

[commit] r1291 - trunk
by repository service 30 Apr '11

30 Apr '11

Author: mkarcher Date: Sat Apr 30 01:53:09 2011 New Revision: 1291 URL: http://flashrom.org/trac/flashrom/changeset/1291 Log: improve output in case run_opcode fails Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Modified: trunk/ichspi.c Modified: trunk/ichspi.c ============================================================================== --- trunk/ichspi.c Sat Apr 30 00:11:36 2011 (r1290) +++ trunk/ichspi.c Sat Apr 30 01:53:09 2011 (r1291) @@ -612,8 +612,7 @@ /* FIXME: make sure we do not needlessly cause transaction errors. */ temp16 = REGREAD16(ICH7_REG_SPIS); if (temp16 & SPIS_FCERR) { - msg_perr("Transaction error for opcode 0x%02x!\n", - op.opcode); + msg_perr("Transaction error!\n"); /* keep reserved bits */ temp16 &= SPIS_RESERVED_MASK; REGWRITE16(ICH7_REG_SPIS, temp16 | SPIS_FCERR); @@ -758,8 +757,7 @@ /* FIXME make sure we do not needlessly cause transaction errors. */ temp32 = REGREAD32(ICH9_REG_SSFS); if (temp32 & SSFS_FCERR) { - msg_perr("Transaction error for opcode 0x%02x!\n", - op.opcode); + msg_perr("Transaction error!\n"); /* keep reserved bits */ temp32 &= SSFS_RESERVED_MASK | SSFC_RESERVED_MASK; /* Clear the transaction error. */ @@ -934,7 +932,24 @@ result = run_opcode(*opcode, addr, count, data); if (result) { - msg_pdbg("run OPCODE 0x%02x failed\n", opcode->opcode); + msg_pdbg("Running OPCODE 0x%02x failed ", opcode->opcode); + if ((opcode->spi_type == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || + (opcode->spi_type == SPI_OPCODE_TYPE_READ_WITH_ADDRESS)) { + msg_pdbg("at address 0x%06x ", addr); + } + msg_pdbg("(payload length was %d).\n", count); + + /* Print out the data array if it contains data to write. + * Errors are detected before the received data is read back into + * the array so it won't make sense to print it then. */ + if ((opcode->spi_type == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || + (opcode->spi_type == SPI_OPCODE_TYPE_WRITE_NO_ADDRESS)) { + int i; + msg_pspew("The data was:\n"); + for(i=0; i<count; i++){ + msg_pspew("%3d: 0x%02x\n", i, data[i]); + } + } } return result;

1 0

[PATCH] improve output in case run_opcode fails
by Stefan Tauner 30 Apr '11

30 Apr '11

Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- ichspi.c | 25 ++++++++++++++++++++----- 1 files changed, 20 insertions(+), 5 deletions(-) diff --git a/ichspi.c b/ichspi.c index 5c66ddd..f47783a 100644 --- a/ichspi.c +++ b/ichspi.c @@ -612,8 +612,7 @@ static int ich7_run_opcode(OPCODE op, uint32_t offset, /* FIXME: make sure we do not needlessly cause transaction errors. */ temp16 = REGREAD16(ICH7_REG_SPIS); if (temp16 & SPIS_FCERR) { - msg_perr("Transaction error for opcode 0x%02x!\n", - op.opcode); + msg_perr("Transaction error!\n"); /* keep reserved bits */ temp16 &= SPIS_RESERVED_MASK; REGWRITE16(ICH7_REG_SPIS, temp16 | SPIS_FCERR); @@ -758,8 +757,7 @@ static int ich9_run_opcode(OPCODE op, uint32_t offset, /* FIXME make sure we do not needlessly cause transaction errors. */ temp32 = REGREAD32(ICH9_REG_SSFS); if (temp32 & SSFS_FCERR) { - msg_perr("Transaction error for opcode 0x%02x!\n", - op.opcode); + msg_perr("Transaction error!\n"); /* keep reserved bits */ temp32 &= SSFS_RESERVED_MASK | SSFC_RESERVED_MASK; /* Clear the transaction error. */ @@ -934,7 +932,24 @@ int ich_spi_send_command(unsigned int writecnt, unsigned int readcnt, result = run_opcode(*opcode, addr, count, data); if (result) { - msg_pdbg("run OPCODE 0x%02x failed\n", opcode->opcode); + msg_pdbg("Running OPCODE 0x%02x failed ", opcode->opcode); + if ((opcode->spi_type == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || + (opcode->spi_type == SPI_OPCODE_TYPE_READ_WITH_ADDRESS)) { + msg_pdbg("at address 0x%06x ", addr); + } + msg_pdbg("(payload length was %d).\n", count); + + /* Print out the data array if it contains data to write. + * Errors are detected before the received data is read back into + * the array so it won't make sense to print it then. */ + if ((opcode->spi_type == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || + (opcode->spi_type == SPI_OPCODE_TYPE_WRITE_NO_ADDRESS)) { + msg_pspew("The data was:\n"); + int i; + for(i=0; i<count; i++){ + msg_pspew("%3d: 0x%02x\n", i, data[i]); + } + } } return result; -- 1.7.1

1 0

Re: [flashrom] [PATCH 5/6] improve output in case run_opcode fails
by Stefan Tauner 30 Apr '11

30 Apr '11

On Fri, 1 Apr 2011 14:33:19 +0200 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> wrote: > diff --git a/ichspi.c b/ichspi.c > index b24b6a0..0ad4f20 100644 > --- a/ichspi.c > +++ b/ichspi.c > ... > @@ -974,7 +973,19 @@ int ich_spi_send_command(unsigned int writecnt, > unsigned int readcnt, > result = run_opcode(*opcode, addr, count, data); > if (result) { > - msg_pdbg("run OPCODE 0x%02x failed\n", > opcode->opcode); > + msg_pdbg("run OPCODE 0x%02x failed at address > 0x%06x.\n", > + opcode->opcode, addr); > + /* Print out the data array if it contains data to > write. > + * Errors are detected before the received data is > read back into > + * the array so it won't make sense to print it > then. */ > + if (((opcode->spi_type == > SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS) || > + (opcode->spi_type == > SPI_OPCODE_TYPE_WRITE_NO_ADDRESS))) { > + msg_pspew("The data was:\n"); > + uint8_t i; > + for(i=0; i<count; i++){ > + msg_pspew("%3d: 0x%02x\n", i, > data[i]); > + } > + } > } self-NAK :) uint8_t is too small and could result in an endless loop. oops. :( this should not happen normally, because devices supported by ichspi.c allow only 16B or 64B data lengths, but we could be called with something bigger i guess. how should this be solved? since "count" will get truncated implicitly when it is used as parameter for "run_opcode" we could do so explicitly before the loop. or an if around the loop checking for count<256. also i would like to include the count like so: "run OPCODE 0x%02x failed at address 0x%06x (length %d).\n" RFC :) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 2

Here's the now (if) ready patch.
by Brandon Dowdy 30 Apr '11

30 Apr '11

Probably this patch is ready now. If not, then a few more problems to fix then.

1 0

Re: [flashrom] [PATCH] ichspi: Increase timeout to 60s for atomic operations
by Carl-Daniel Hailfinger 30 Apr '11

30 Apr '11

Am 29.04.2011 16:01 schrieb Michael Karcher: > Signed-off-by: Michael Karcher<flashrom(a)mkarcher.dialup.fu-berlin.de> > Thanks for the patch and for tracking this down and for writing a thorough analysis! Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Could you fix the whitespace before commit? > @@ -581,6 +588,7 @@ static int ich7_run_opcode(OPCODE op, uint32_t offset, > case 1: > /* Atomic command (preop+op) */ > temp16 |= SPIC_ACS; > + timeout = 100 * 1000* 60; /* 60 seconds */ > Should have a space after 1000 > break; > } > > @@ -720,6 +734,7 @@ static int ich9_run_opcode(OPCODE op, uint32_t offset, > case 1: > /* Atomic command (preop+op) */ > temp32 |= SSFC_ACS; > + timeout = 100 * 1000* 60; /* 60 seconds */ > Same here. > break; > } > > Regards, Carl-Daniel -- http://www.hailfinger.org/

2 1

[commit] r1290 - trunk
by repository service 30 Apr '11

30 Apr '11

Author: mkarcher Date: Sat Apr 30 00:11:36 2011 New Revision: 1290 URL: http://flashrom.org/trac/flashrom/changeset/1290 Log: ichspi: Increase timeout to 60s for atomic operations Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/ichspi.c Modified: trunk/ichspi.c ============================================================================== --- trunk/ichspi.c Wed Apr 27 16:34:08 2011 (r1289) +++ trunk/ichspi.c Sat Apr 30 00:11:36 2011 (r1290) @@ -572,7 +572,14 @@ } temp16 |= ((uint16_t) (opcode_index & 0x07)) << 4; - /* Handle Atomic */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + /* Handle Atomic. Atomic commands include three steps: + - sending the preop (mainly EWSR or WREN) + - sending the main command + - waiting for the busy bit (WIP) to be cleared + This means the timeout must be sufficient for chip erase + of slow high-capacity chips. + */ switch (op.atomic) { case 2: /* Select second preop. */ @@ -581,6 +588,7 @@ case 1: /* Atomic command (preop+op) */ temp16 |= SPIC_ACS; + timeout = 100 * 1000 * 60; /* 60 seconds */ break; } @@ -591,7 +599,6 @@ REGWRITE16(ICH7_REG_SPIC, temp16); /* Wait for Cycle Done Status or Flash Cycle Error. */ - timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ while (((REGREAD16(ICH7_REG_SPIS) & (SPIS_CDS | SPIS_FCERR)) == 0) && --timeout) { programmer_delay(10); @@ -711,7 +718,14 @@ } temp32 |= ((uint32_t) (opcode_index & 0x07)) << (8 + 4); - /* Handle Atomic */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + /* Handle Atomic. Atomic commands include three steps: + - sending the preop (mainly EWSR or WREN) + - sending the main command + - waiting for the busy bit (WIP) to be cleared + This means the timeout must be sufficient for chip erase + of slow high-capacity chips. + */ switch (op.atomic) { case 2: /* Select second preop. */ @@ -720,6 +734,7 @@ case 1: /* Atomic command (preop+op) */ temp32 |= SSFC_ACS; + timeout = 100 * 1000 * 60; /* 60 seconds */ break; } @@ -730,7 +745,6 @@ REGWRITE32(ICH9_REG_SSFS, temp32); /* Wait for Cycle Done Status or Flash Cycle Error. */ - timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ while (((REGREAD32(ICH9_REG_SSFS) & (SSFS_CDS | SSFS_FCERR)) == 0) && --timeout) { programmer_delay(10);

1 0

Here's the properly fixed patch.
by Brandon Dowdy 29 Apr '11

29 Apr '11

Here is the properly and completely fixed patch.

1 0

Re: [flashrom] Problem H55M-S Foxconn
by Idwer Vollering 29 Apr '11

29 Apr '11

Forwarding his reply. 2011/4/29 Marcelo Sales Moreira <marcelo.sales(a)litecnologia.com.br>: > Good morning, > > I tested with version 0.9.3 and not work with the bios file that the > vendor sent me to work I had to update the bios file with custom bios / > upgrade software and then save with AFUDOS.EXE FlashROM, ai yes I could > replicate the bios saved for other boards. > > Attached is the original bios and bios saved with FlashROM Attached were: bios_save_flash.rom 4194304 bytes bios_logo.rom 1048576 bytes You can create a file that has the same size as "bios_save_flash.rom" / the chip size by doing this: cat bios_logo.rom bios_logo.rom bios_logo.rom bios_logo.rom >> bios_logo_4megabyte.rom We are also interested in the output of "flashrom -V -w bios_logo_4megabyte.rom" > > Att > Marcelo Moreira Sales > > > Em Qui, 2011-04-28 às 22:12 +0200, Idwer Vollering escreveu: >> 2011/4/28 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at>: >> > >> > >> > Begin forwarded message: >> > >> > Date: Thu, 28 Apr 2011 13:46:51 -0300 >> > From: Marcelo Sales Moreira <marcelo.sales(a)litecnologia.com.br> >> > To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> >> > Subject: Re: [flashrom] Problem H55M-S Foxconn >> > >> > >> > Good afternoon, >> > >> > Attached is the output from-v FlashROM >> >> By looking at the output, I recommend to use version 0.9.3 or building >> the latest development code: >> http://www.flashrom.org/Downloads#Installation_from_source >> >> > >> > Att >> > Marcelo Moreira Sales >> > >> > >> > -- >> > Kind regards/Mit freundlichen Grüßen, Stefan Tauner >> > >> > _______________________________________________ >> > flashrom mailing list >> > flashrom(a)flashrom.org >> > http://www.flashrom.org/mailman/listinfo/flashrom >> > >> > >

1 0

[PATCH] ichspi: Increase timeout to 60s for atomic operations
by Michael Karcher 29 Apr '11

29 Apr '11

Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> --- ichspi.c | 22 ++++++++++++++++++---- 1 files changed, 18 insertions(+), 4 deletions(-) diff --git a/ichspi.c b/ichspi.c index ed92893..db5ec75 100644 --- a/ichspi.c +++ b/ichspi.c @@ -572,7 +572,14 @@ static int ich7_run_opcode(OPCODE op, uint32_t offset, } temp16 |= ((uint16_t) (opcode_index & 0x07)) << 4; - /* Handle Atomic */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + /* Handle Atomic. Atomic commands include three steps: + - sending the preop (mainly EWSR or WREN) + - sending the main command + - waiting for the busy bit (WIP) to be cleared + This means the timeout must be sufficient for chip erase + of slow high-capacity chips. + */ switch (op.atomic) { case 2: /* Select second preop. */ @@ -581,6 +588,7 @@ static int ich7_run_opcode(OPCODE op, uint32_t offset, case 1: /* Atomic command (preop+op) */ temp16 |= SPIC_ACS; + timeout = 100 * 1000* 60; /* 60 seconds */ break; } @@ -591,7 +599,6 @@ static int ich7_run_opcode(OPCODE op, uint32_t offset, REGWRITE16(ICH7_REG_SPIC, temp16); /* Wait for Cycle Done Status or Flash Cycle Error. */ - timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ while (((REGREAD16(ICH7_REG_SPIS) & (SPIS_CDS | SPIS_FCERR)) == 0) && --timeout) { programmer_delay(10); @@ -711,7 +718,14 @@ static int ich9_run_opcode(OPCODE op, uint32_t offset, } temp32 |= ((uint32_t) (opcode_index & 0x07)) << (8 + 4); - /* Handle Atomic */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + /* Handle Atomic. Atomic commands include three steps: + - sending the preop (mainly EWSR or WREN) + - sending the main command + - waiting for the busy bit (WIP) to be cleared + This means the timeout must be sufficient for chip erase + of slow high-capacity chips. + */ switch (op.atomic) { case 2: /* Select second preop. */ @@ -720,6 +734,7 @@ static int ich9_run_opcode(OPCODE op, uint32_t offset, case 1: /* Atomic command (preop+op) */ temp32 |= SSFC_ACS; + timeout = 100 * 1000* 60; /* 60 seconds */ break; } @@ -730,7 +745,6 @@ static int ich9_run_opcode(OPCODE op, uint32_t offset, REGWRITE32(ICH9_REG_SSFS, temp32); /* Wait for Cycle Done Status or Flash Cycle Error. */ - timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ while (((REGREAD32(ICH9_REG_SSFS) & (SSFS_CDS | SSFS_FCERR)) == 0) && --timeout) { programmer_delay(10); -- 1.7.4.1

1 0

reading BIOS setting using Flashrom
by ganesh.patwardhan＠wipro.com 29 Apr '11

29 Apr '11

Hi, Is it possible to read only BIOS setting and store in a file using Flashrom? Example :- say I want to read BIOS settings like Signature, boot order, Numlock setting etc... from Linux using Flashrom. Regards Ganesh Patwardhan Please do not print this email unless it is absolutely necessary. The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. www.wipro.com

1 0

CHIPSET: Sun Fire x4100
by Stefan Reinauer 29 Apr '11

29 Apr '11

flashrom v0.9.3-r1283 on Linux 2.6.31.14-0.6-default (x86_64), built with libpci 3.1.3, GCC 4.4.1 [gcc-4_4-branch revision 150839], little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "NVIDIA CK804", enabling flash write... OK. WARNING: unexpected second chipset match: "NVIDIA CK804" ignoring, please report lspci and board URL to flashrom(a)flashrom.org with 'CHIPSET: your board name' in the subject line. This chipset supports the following protocols: Non-SPI. Found chip "ST M50FLW080A" (1024 KB, LPC,FWH) at physical address 0xfff00000. === This flash part has status UNTESTED for operations: WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified. ra:~ # lspci 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1) 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4) 00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f3) 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) 00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev f3) 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 80:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) 80:01.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev f1) 80:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev f3) 80:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 80:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 80:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) 80:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 80:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) 80:10.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) 80:11.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) 80:11.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) 86:01.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 03) 86:01.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 03) 86:02.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064 PCI-X Fusion-MPT SAS (rev 02)

1 0

Debugging FT4232H
by David Hendricks 28 Apr '11

28 Apr '11

Hi, I'm using Flashrom with an FTDI FT4232H to read a 1MB SPI ROM (w25q80), but am encountering difficulties. I believe we may be missing some steps in ft2232_spi_init(), however I don't have much experience with libftdi or usb debugging so I hope someone on the list does :-) When the programmer is plugged into a "full-speed" USB port slow, things seem to work well. However, when plugged into a "high-speed" port, bytes simply disappear. There does not seem to be a pattern with regard to where the problems start. Sometimes it will fail very early and Flashrom will not be able to detect the chip. Sometimes we'll get lucky and we can read the full chip. It can fail anywhere in between. The only pattern I've seen is that usb bulk reads return less than the requested number of bytes before it fails entirely. For example, if we request 256 bytes, then it might return 256-N data bytes. libftdi will request the remaining bytes, and libusb will provide the remaining N data bytes. On the next 256-byte request, libusb will not return any data bytes (only the 2-byte USB header). I added a bunch of debug prints to libftdi and libusb to get a better idea of what's happening deeper in the stack. Here is a sample of what we see (with added comments) when it fails: Invocation: flashrom -p ft2232_spi:type=4232H,port=A -r /tmp/foo.bin Successful 256-byte read: writecnt: 4, writearr: 03 02 c3 00 <--- SPI command. 03 indicates read, 02 c3 00 is the address. getting buffer from ftdi... usb_bulk_read ret: 258 "offset" from ftdi_read_data(): 256 get_buf returned with 0 A troubled 256-byte read follows: writecnt: 4, writearr: 03 02 c4 00 getting buffer from ftdi... usb_bulk_read ret: 45 <--- (45-2) + (142-2) + (75-2) = 256 usb_bulk_read ret: 142 usb_bulk_read ret: 75 "offset" from ftdi_read_data(): 256 get_buf returned with 0 And now it simply fails to read anything: writecnt: 4, writearr: 03 02 c5 00 getting buffer from ftdi... usb_bulk_read ret: 211 <--- returns 209 data bytes usb_bulk_read ret: 2 <--- fails to read any more data bytes "offset" from ftdi_read_data(): 209 usb_bulk_read ret: 2 get_buf: no data was available "offset" from ftdi_read_data(): 0 usb_bulk_read ret: 2 libftdi's ftdi_read_data() will loop indefinitely here until the remaining data bytes arrive, which never happens. Any ideas on what could be causing this are appreciated! -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc.

2 2

Re: [flashrom] Problem H55M-S Foxconn
by Stefan Tauner 28 Apr '11

28 Apr '11

Begin forwarded message: Date: Thu, 28 Apr 2011 13:46:51 -0300 From: Marcelo Sales Moreira <marcelo.sales(a)litecnologia.com.br> To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Subject: Re: [flashrom] Problem H55M-S Foxconn Good afternoon, Attached is the output from-v FlashROM Att Marcelo Moreira Sales -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Problem H55M-S Foxconn
by Marcelo Sales Moreira 28 Apr '11

28 Apr '11

Good morning, I am having problem with the motherboard model H55M-S Foxconn, I wonder if there any solution to solve this problem. Att Marcelo Moreira Sales

2 1

here's the completely fixed patch.
by Brandon Dowdy 28 Apr '11

28 Apr '11

Here is the same patch that is completely looked at and fixed.

3 2

Here's the resent patch.
by Brandon Dowdy 27 Apr '11

27 Apr '11

Here is the same patch.

1 0

[RFC] cheapish and free usb spi flashing device
by Stefan Tauner 27 Apr '11

27 Apr '11

hey there! (cross-posted to both mailing lists) i am currently designing a small and cheap platform to recover from coreboot and other failures easily. the reason i am writing this is to get feedback from you regarding desired features of and interest in such a device. right now my plan is the following: an avr atmegaXXu2 is connected via usb and implements the serprog protocol to let flashrom make use of it. the avr can operate down to 3.0V which would allow easy interfacing with today's spi flashes without any level shifting. to get the desired supply voltage from usb's 5V i will use a fixed 3.3V ldo voltage regulator (ld1117). apart from a few supporting parts (caps, fuse, usb line termination etc.) the only things missing are sockets for the spi chips. at the moment i am planing to include: - soic8 pads (combined for 150 and 200mil devices) and enough room for a soic8 zif adapter (like the one from http://bios-repair.co.uk) - vias for a 24 pin zif dip/dil socket (150 and 300mil spacing combined): 8 pins for dip8 flashes and 16 for soic16 flashes (those would require a soic to dip adapter). 8pin and 16pin flashes dont share pins therefore the large socket... - vias for a single row 8pin header to allow attaching probes/test clips (e.g. http://www.pomonaelectronics.com/images/large/6109.jpg) to hook up in-situ flashes. parts for this excluding the pcb would be in the 10-25$ range. depending on how many pcbs i/we would produce the whole thing would cost probably about 40$. not THAT cheap, but quite better than the dediprog stuff :) it would also be more convenient and open than the FT2232SPI based on the DLP-USB1232H (http://flashrom.org/FT2232SPI_Programmer). the willem programmers seem to be lpt only? are there any other cheap flashers i dont know? i am not sure about what to do with soic16 chips. the solution laid out above which requires an additional adapter and wastes a lot of space is awkward. should i just include soic16 pads instead? should i drop support for them altogether and let the user hook them up with clips? are they in use anywhere? my intel desktop board has pads for it, but i am not sure if there are any boards in the wild which really use them... i was also thinking about an offline mode which uses an SD-card or another flash to store/load an image for the target flash. push buttons would activate a cloning operation. this way one could clone chips easily without a pc, but i am not sure at all if thats worth it. what do you think? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

4 6

[PATCH] Support more than one EC/SuperIO at a time
by Carl-Daniel Hailfinger 27 Apr '11

27 Apr '11

flashrom currently only supports exactly one Super I/O or Embedded Controller, and this means quite a few notebooks and a small subset of desktop/server boards cannot be handled reliably and easily. Allow detection and initialization of up to 3 Super I/O and/or EC chips. Please test with boards using - IT8705 MEMW enable for parallel flash - IT8712/IT8716/... SPI flash - IT85* laptops (probably Cr-48) This patch applies on top of [PATCH] IT85* cleanups/fixes . WARNING! IT85* support is commented out for now until the improved laptop framework is merged. You must enable it manually by uncommenting the call to it85xx_spi_init(superios[i]) in it87spi.c or flashrom will not work on the Google Cr-48. WARNING! If a Super I/O or EC responds on multiple ports (0x2e and 0x4e), the code will do the wrong thing (namely, initialize the hardware twice). I have no idea if we should handle such situations, and whether we should ignore the second chip with identical ID or not. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> diff -ru flashrom-it85spi_cleanup/flashrom.c flashrom-register_superio/flashrom.c --- flashrom-it85spi_cleanup/flashrom.c 2011-02-22 18:12:42.000000000 +0100 +++ flashrom-register_superio/flashrom.c 2011-03-04 00:52:42.000000000 +0100 @@ -310,27 +310,6 @@ }, #endif -#if CONFIG_INTERNAL == 1 -#if defined(__i386__) || defined(__x86_64__) - { - .name = "it87spi", - .init = it87spi_init, - .shutdown = noop_shutdown, - .map_flash_region = fallback_map, - .unmap_flash_region = fallback_unmap, - .chip_readb = noop_chip_readb, - .chip_readw = fallback_chip_readw, - .chip_readl = fallback_chip_readl, - .chip_readn = fallback_chip_readn, - .chip_writeb = noop_chip_writeb, - .chip_writew = fallback_chip_writew, - .chip_writel = fallback_chip_writel, - .chip_writen = fallback_chip_writen, - .delay = internal_delay, - }, -#endif -#endif - #if CONFIG_FT2232_SPI == 1 { .name = "ft2232_spi", diff -ru flashrom-it85spi_cleanup/internal.c flashrom-register_superio/internal.c --- flashrom-it85spi_cleanup/internal.c 2011-02-22 18:54:49.000000000 +0100 +++ flashrom-register_superio/internal.c 2011-03-04 00:33:47.000000000 +0100 @@ -99,17 +99,29 @@ int force_boardmismatch = 0; #if defined(__i386__) || defined(__x86_64__) -struct superio superio = {}; - void probe_superio(void) { - superio = probe_superio_ite(); + probe_superio_ite(); #if 0 /* Winbond Super I/O code is not yet available. */ if (superio.vendor == SUPERIO_VENDOR_NONE) superio = probe_superio_winbond(); #endif } + +int superio_count = 0; +#define SUPERIO_MAX_COUNT 3 + +struct superio superios[SUPERIO_MAX_COUNT]; + +int register_superio(struct superio s) +{ + if (superio_count == SUPERIO_MAX_COUNT) + return 1; + superios[superio_count++] = s; + return 0; +} + #endif int is_laptop = 0; diff -ru flashrom-it85spi_cleanup/it85spi.c flashrom-register_superio/it85spi.c --- flashrom-it85spi_cleanup/it85spi.c 2011-03-04 00:16:48.000000000 +0100 +++ flashrom-register_superio/it85spi.c 2011-03-04 01:40:57.000000000 +0100 @@ -47,9 +47,6 @@ /* Constants for Logical Device registers */ #define LDNSEL 0x07 -#define CHIP_ID_BYTE1_REG 0x20 -#define CHIP_ID_BYTE2_REG 0x21 -#define CHIP_CHIP_VER_REG 0x22 /* These are standard Super I/O 16-bit base address registers */ #define SHM_IO_BAR0 0x60 /* big-endian, this is high bits */ @@ -86,44 +83,6 @@ unsigned char *ce_high, *ce_low; static int it85xx_scratch_rom_reenter = 0; -uint16_t probe_id_ite85(uint16_t port) -{ - uint16_t id; - - id = sio_read(port, CHIP_ID_BYTE1_REG) << 8 | - sio_read(port, CHIP_ID_BYTE2_REG); - - return id; -} - -struct superio probe_superio_ite85xx(void) -{ - struct superio ret = {}; - uint16_t ite_ports[] = {ITE_SUPERIO_PORT1, ITE_SUPERIO_PORT2, 0}; - uint16_t *i = ite_ports; - - ret.vendor = SUPERIO_VENDOR_ITE; - for (; *i; i++) { - ret.port = *i; - ret.model = probe_id_ite85(ret.port); - switch (ret.model >> 8) { - case 0x85: - msg_pdbg("Found EC: ITE85xx (Vendor:0x%02x,ID:0x%02x," - "Rev:0x%02x) on sio_port:0x%x.\n", - ret.model >> 8, ret.model & 0xff, - sio_read(ret.port, CHIP_CHIP_VER_REG), - ret.port); - return ret; - } - } - - /* No good ID found. */ - ret.vendor = SUPERIO_VENDOR_NONE; - ret.port = 0; - ret.model = 0; - return ret; -} - /* This function will poll the keyboard status register until either * an expected value shows up, or * timeout reaches. @@ -267,20 +226,18 @@ #endif } -int it85xx_spi_common_init(void) +static int it85xx_spi_common_init(struct superio s) { chipaddr base; msg_pdbg("%s():%d superio.vendor=0x%02x\n", __func__, __LINE__, - superio.vendor); - if (superio.vendor != SUPERIO_VENDOR_ITE) - return 1; + s.vendor); #ifdef LPC_IO /* Get LPCPNP of SHM. That's big-endian */ - sio_write(superio.port, LDNSEL, 0x0F); /* Set LDN to SHM (0x0F) */ - shm_io_base = (sio_read(superio.port, SHM_IO_BAR0) << 8) + - sio_read(superio.port, SHM_IO_BAR1); + sio_write(s.port, LDNSEL, 0x0F); /* Set LDN to SHM (0x0F) */ + shm_io_base = (sio_read(s.port, SHM_IO_BAR0) << 8) + + sio_read(s.port, SHM_IO_BAR1); msg_pdbg("%s():%d shm_io_base=0x%04x\n", __func__, __LINE__, shm_io_base); @@ -311,25 +268,7 @@ return 0; } -/* Called by programmer_entry .init */ -int it85xx_spi_init(void) -{ - int ret; - - get_io_perms(); - /* Probe for the Super I/O chip and fill global struct superio. */ - probe_superio(); - ret = it85xx_spi_common_init(); - if (!ret) { - buses_supported = CHIP_BUSTYPE_SPI; - } else { - buses_supported = CHIP_BUSTYPE_NONE; - } - return ret; -} - -/* Called by internal_init() */ -int it85xx_probe_spi_flash(void) +int it85xx_spi_init(struct superio s) { int ret; @@ -337,13 +276,14 @@ msg_pdbg("%s():%d buses not support FWH\n", __func__, __LINE__); return 1; } - ret = it85xx_spi_common_init(); + ret = it85xx_spi_common_init(s); msg_pdbg("FWH: %s():%d ret=%d\n", __func__, __LINE__, ret); if (!ret) { msg_pdbg("%s():%d buses_supported=0x%x\n", __func__, __LINE__, buses_supported); if (buses_supported & CHIP_BUSTYPE_FWH) msg_pdbg("Overriding chipset SPI with IT85 FWH|SPI.\n"); + /* Really leave FWH enabled? */ buses_supported |= CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; } return ret; diff -ru flashrom-it85spi_cleanup/it87spi.c flashrom-register_superio/it87spi.c --- flashrom-it85spi_cleanup/it87spi.c 2011-02-22 18:11:33.000000000 +0100 +++ flashrom-register_superio/it87spi.c 2011-03-04 01:19:52.000000000 +0100 @@ -42,6 +42,7 @@ /* Helper functions for most recent ITE IT87xx Super I/O chips */ #define CHIP_ID_BYTE1_REG 0x20 #define CHIP_ID_BYTE2_REG 0x21 +#define CHIP_VER_REG 0x22 void enter_conf_mode_ite(uint16_t port) { OUTB(0x87, port); @@ -70,31 +71,37 @@ return id; } -struct superio probe_superio_ite(void) +void probe_superio_ite(void) { - struct superio ret = {}; + struct superio s = {}; uint16_t ite_ports[] = {ITE_SUPERIO_PORT1, ITE_SUPERIO_PORT2, 0}; uint16_t *i = ite_ports; - ret.vendor = SUPERIO_VENDOR_ITE; + s.vendor = SUPERIO_VENDOR_ITE; for (; *i; i++) { - ret.port = *i; - ret.model = probe_id_ite(ret.port); - switch (ret.model >> 8) { + s.port = *i; + s.model = probe_id_ite(s.port); + switch (s.model >> 8) { case 0x82: case 0x86: case 0x87: - msg_pinfo("Found ITE Super I/O, ID 0x%04hx.\n", - ret.model); - return ret; + /* FIXME: Print revision for all models? */ + msg_pdbg("Found ITE Super I/O, ID 0x%04hx on port " + "0x%x\n", s.model, s.port); + register_superio(s); + break; + case 0x85: + msg_pdbg("Found ITE EC, ID 0x%04hx," + "Rev 0x%02x on port 0x%x.\n", + s.model, + sio_read(s.port, CHIP_VER_REG), + s.port); + register_superio(s); + break; } } - /* No good ID found. */ - ret.vendor = SUPERIO_VENDOR_NONE; - ret.port = 0; - ret.model = 0; - return ret; + return; } static uint16_t it87spi_probe(uint16_t port) @@ -183,38 +190,39 @@ int init_superio_ite(void) { - if (superio.vendor != SUPERIO_VENDOR_ITE) - return 1; - - switch (superio.model) { - case 0x8705: - return it8705f_write_enable(superio.port); - break; - case 0x8716: - case 0x8718: - case 0x8720: - return it87spi_probe(superio.port); - break; - default: - msg_pdbg("Super I/O ID 0x%04hx is not on the list of flash " - "capable controllers.\n", superio.model); - } - return 1; -} - - -int it87spi_init(void) -{ - int ret; + int i; + int ret = 0; - get_io_perms(); - /* Probe for the Super I/O chip and fill global struct superio. */ - probe_superio(); - ret = init_superio_ite(); - if (!ret) { - buses_supported = CHIP_BUSTYPE_SPI; - } else { - buses_supported = CHIP_BUSTYPE_NONE; + for (i = 0; i < superio_count; i++) { + if (superios[i].vendor != SUPERIO_VENDOR_ITE) + continue; + + switch (superios[i].model) { + case 0x8500: + case 0x8502: + case 0x8510: + case 0x8511: + case 0x8512: + /* FIXME: This should be enabled, but we need a check + * for laptop whitelisting due to the amount of things + * which can go wrong if the EC firmware does not + * implement the interface we want. + */ + //it85xx_spi_init(superios[i]); + break; + case 0x8705: + ret |= it8705f_write_enable(superios[i].port); + break; + case 0x8716: + case 0x8718: + case 0x8720: + ret |= it87spi_probe(superios[i].port); + break; + default: + msg_pdbg("Super I/O ID 0x%04hx is not on the list of " + "flash capable controllers.\n", + superios[i].model); + } } return ret; } @@ -323,10 +331,13 @@ */ int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len) { - int total_size = 1024 * flash->total_size; fast_spi = 0; - if ((programmer == PROGRAMMER_IT87SPI) || (total_size > 512 * 1024)) { + /* FIXME: Check if someone explicitly requested to use IT87 SPI although + * the mainboard does not use IT87 SPI translation. This should be done + * via a programmer parameter for the internal programmer. + */ + if ((flash->total_size * 1024 > 512 * 1024)) { spi_read_chunked(flash, buf, start, len, 3); } else { read_memmapped(flash, buf, start, len); @@ -343,9 +354,11 @@ * so page_size > 256 bytes needs a fallback. * FIXME: Split too big page writes into chunks IT87* can handle instead * of degrading to single-byte program. + * FIXME: Check if someone explicitly requested to use IT87 SPI although + * the mainboard does not use IT87 SPI translation. This should be done + * via a programmer parameter for the internal programmer. */ - if ((programmer == PROGRAMMER_IT87SPI) || - (flash->total_size * 1024 > 512 * 1024) || + if ((flash->total_size * 1024 > 512 * 1024) || (flash->page_size > 256)) { spi_chip_write_1(flash, buf, start, len); } else { diff -ru flashrom-it85spi_cleanup/programmer.h flashrom-register_superio/programmer.h --- flashrom-it85spi_cleanup/programmer.h 2011-03-01 01:19:58.000000000 +0100 +++ flashrom-register_superio/programmer.h 2011-03-04 00:56:59.000000000 +0100 @@ -53,11 +53,6 @@ #if CONFIG_ATAHPT == 1 PROGRAMMER_ATAHPT, #endif -#if CONFIG_INTERNAL == 1 -#if defined(__i386__) || defined(__x86_64__) - PROGRAMMER_IT87SPI, -#endif -#endif #if CONFIG_FT2232_SPI == 1 PROGRAMMER_FT2232_SPI, #endif @@ -274,7 +269,8 @@ uint16_t port; uint16_t model; }; -extern struct superio superio; +extern struct superio superios[]; +extern int superio_count; #define SUPERIO_VENDOR_NONE 0x0 #define SUPERIO_VENDOR_ITE 0x1 struct pci_dev *pci_dev_find_filter(struct pci_filter filter); @@ -290,6 +286,7 @@ extern int force_boardenable; extern int force_boardmismatch; void probe_superio(void); +int register_superio(struct superio s); int internal_init(void); int internal_shutdown(void); void internal_chip_writeb(uint8_t val, chipaddr addr); @@ -585,10 +582,8 @@ #endif /* it85spi.c */ -struct superio probe_superio_ite85xx(void); -int it85xx_spi_init(void); +int it85xx_spi_init(struct superio s); int it85xx_shutdown(void); -int it85xx_probe_spi_flash(void); int it85xx_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int it85_spi_read(struct flashchip *flash, uint8_t * buf, int start, int len); @@ -597,9 +592,8 @@ /* it87spi.c */ void enter_conf_mode_ite(uint16_t port); void exit_conf_mode_ite(uint16_t port); -struct superio probe_superio_ite(void); +void probe_superio_ite(void); int init_superio_ite(void); -int it87spi_init(void); int it8716f_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len); -- http://www.hailfinger.org/

2 5

[commit] r1289 - trunk
by repository service 27 Apr '11

27 Apr '11

Author: hailfinger Date: Wed Apr 27 16:34:08 2011 New Revision: 1289 URL: http://flashrom.org/trac/flashrom/changeset/1289 Log: Add support for more than one Super I/O or EC per machine. flashrom currently only supports exactly one Super I/O or Embedded Controller, and this means quite a few notebooks and a small subset of desktop/server boards cannot be handled reliably and easily. Allow detection and initialization of up to 3 Super I/O and/or EC chips. WARNING! If a Super I/O or EC responds on multiple ports (0x2e and 0x4e), the code will do the wrong thing (namely, initialize the hardware twice). I have no idea if we should handle such situations, and whether we should ignore the second chip with identical ID or not. Initializing the hardware twice for the IT87* family is _not_ a problem, but I don't know how well IT85* can handle it (and whether IT85* would listen at more than one port anyway). Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Thanks to Thomas Schneider for testing on a board with ITE IT87* SPI. Test report (success) is here: http://paste.flashrom.org/view.php?id=379 Thanks to David Hendricks for testing on a Google Cr-48 laptop with ITE IT85* EC SPI. Test report (success) is here: http://www.flashrom.org/pipermail/flashrom/2011-April/006275.html Acked-by: David Hendricks <dhendrix(a)google.com> Modified: trunk/board_enable.c trunk/flashrom.c trunk/internal.c trunk/it85spi.c trunk/it87spi.c trunk/programmer.h Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/board_enable.c Wed Apr 27 16:34:08 2011 (r1289) @@ -493,7 +493,6 @@ } } else { msg_pdbg("No IT8705F flash segment enabled.\n"); - /* Not sure if this is an error or not. */ ret = 0; } exit_conf_mode_ite(port); Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/flashrom.c Wed Apr 27 16:34:08 2011 (r1289) @@ -295,27 +295,6 @@ }, #endif -#if CONFIG_INTERNAL == 1 -#if defined(__i386__) || defined(__x86_64__) - { - .name = "it87spi", - .init = it87spi_init, - .shutdown = noop_shutdown, - .map_flash_region = fallback_map, - .unmap_flash_region = fallback_unmap, - .chip_readb = noop_chip_readb, - .chip_readw = fallback_chip_readw, - .chip_readl = fallback_chip_readl, - .chip_readn = fallback_chip_readn, - .chip_writeb = noop_chip_writeb, - .chip_writew = fallback_chip_writew, - .chip_writel = fallback_chip_writel, - .chip_writen = fallback_chip_writen, - .delay = internal_delay, - }, -#endif -#endif - #if CONFIG_FT2232_SPI == 1 { .name = "ft2232_spi", Modified: trunk/internal.c ============================================================================== --- trunk/internal.c Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/internal.c Wed Apr 27 16:34:08 2011 (r1289) @@ -99,17 +99,29 @@ int force_boardmismatch = 0; #if defined(__i386__) || defined(__x86_64__) -struct superio superio = {}; - void probe_superio(void) { - superio = probe_superio_ite(); + probe_superio_ite(); #if 0 /* Winbond Super I/O code is not yet available. */ if (superio.vendor == SUPERIO_VENDOR_NONE) superio = probe_superio_winbond(); #endif } + +int superio_count = 0; +#define SUPERIO_MAX_COUNT 3 + +struct superio superios[SUPERIO_MAX_COUNT]; + +int register_superio(struct superio s) +{ + if (superio_count == SUPERIO_MAX_COUNT) + return 1; + superios[superio_count++] = s; + return 0; +} + #endif int is_laptop = 0; Modified: trunk/it85spi.c ============================================================================== --- trunk/it85spi.c Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/it85spi.c Wed Apr 27 16:34:08 2011 (r1289) @@ -47,9 +47,6 @@ /* Constants for Logical Device registers */ #define LDNSEL 0x07 -#define CHIP_ID_BYTE1_REG 0x20 -#define CHIP_ID_BYTE2_REG 0x21 -#define CHIP_CHIP_VER_REG 0x22 /* These are standard Super I/O 16-bit base address registers */ #define SHM_IO_BAR0 0x60 /* big-endian, this is high bits */ @@ -86,44 +83,6 @@ unsigned char *ce_high, *ce_low; static int it85xx_scratch_rom_reenter = 0; -uint16_t probe_id_ite85(uint16_t port) -{ - uint16_t id; - - id = sio_read(port, CHIP_ID_BYTE1_REG) << 8 | - sio_read(port, CHIP_ID_BYTE2_REG); - - return id; -} - -struct superio probe_superio_ite85xx(void) -{ - struct superio ret = {}; - uint16_t ite_ports[] = {ITE_SUPERIO_PORT1, ITE_SUPERIO_PORT2, 0}; - uint16_t *i = ite_ports; - - ret.vendor = SUPERIO_VENDOR_ITE; - for (; *i; i++) { - ret.port = *i; - ret.model = probe_id_ite85(ret.port); - switch (ret.model >> 8) { - case 0x85: - msg_pdbg("Found EC: ITE85xx (Vendor:0x%02x,ID:0x%02x," - "Rev:0x%02x) on sio_port:0x%x.\n", - ret.model >> 8, ret.model & 0xff, - sio_read(ret.port, CHIP_CHIP_VER_REG), - ret.port); - return ret; - } - } - - /* No good ID found. */ - ret.vendor = SUPERIO_VENDOR_NONE; - ret.port = 0; - ret.model = 0; - return ret; -} - /* This function will poll the keyboard status register until either * an expected value shows up, or * timeout reaches. @@ -267,20 +226,18 @@ #endif } -int it85xx_spi_common_init(void) +static int it85xx_spi_common_init(struct superio s) { chipaddr base; msg_pdbg("%s():%d superio.vendor=0x%02x\n", __func__, __LINE__, - superio.vendor); - if (superio.vendor != SUPERIO_VENDOR_ITE) - return 1; + s.vendor); #ifdef LPC_IO /* Get LPCPNP of SHM. That's big-endian */ - sio_write(superio.port, LDNSEL, 0x0F); /* Set LDN to SHM (0x0F) */ - shm_io_base = (sio_read(superio.port, SHM_IO_BAR0) << 8) + - sio_read(superio.port, SHM_IO_BAR1); + sio_write(s.port, LDNSEL, 0x0F); /* Set LDN to SHM (0x0F) */ + shm_io_base = (sio_read(s.port, SHM_IO_BAR0) << 8) + + sio_read(s.port, SHM_IO_BAR1); msg_pdbg("%s():%d shm_io_base=0x%04x\n", __func__, __LINE__, shm_io_base); @@ -311,25 +268,7 @@ return 0; } -/* Called by programmer_entry .init */ -int it85xx_spi_init(void) -{ - int ret; - - get_io_perms(); - /* Probe for the Super I/O chip and fill global struct superio. */ - probe_superio(); - ret = it85xx_spi_common_init(); - if (!ret) { - buses_supported = CHIP_BUSTYPE_SPI; - } else { - buses_supported = CHIP_BUSTYPE_NONE; - } - return ret; -} - -/* Called by internal_init() */ -int it85xx_probe_spi_flash(void) +int it85xx_spi_init(struct superio s) { int ret; @@ -337,13 +276,14 @@ msg_pdbg("%s():%d buses not support FWH\n", __func__, __LINE__); return 1; } - ret = it85xx_spi_common_init(); + ret = it85xx_spi_common_init(s); msg_pdbg("FWH: %s():%d ret=%d\n", __func__, __LINE__, ret); if (!ret) { msg_pdbg("%s():%d buses_supported=0x%x\n", __func__, __LINE__, buses_supported); if (buses_supported & CHIP_BUSTYPE_FWH) msg_pdbg("Overriding chipset SPI with IT85 FWH|SPI.\n"); + /* Really leave FWH enabled? */ buses_supported |= CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; } return ret; Modified: trunk/it87spi.c ============================================================================== --- trunk/it87spi.c Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/it87spi.c Wed Apr 27 16:34:08 2011 (r1289) @@ -42,6 +42,7 @@ /* Helper functions for most recent ITE IT87xx Super I/O chips */ #define CHIP_ID_BYTE1_REG 0x20 #define CHIP_ID_BYTE2_REG 0x21 +#define CHIP_VER_REG 0x22 void enter_conf_mode_ite(uint16_t port) { OUTB(0x87, port); @@ -70,31 +71,37 @@ return id; } -struct superio probe_superio_ite(void) +void probe_superio_ite(void) { - struct superio ret = {}; + struct superio s = {}; uint16_t ite_ports[] = {ITE_SUPERIO_PORT1, ITE_SUPERIO_PORT2, 0}; uint16_t *i = ite_ports; - ret.vendor = SUPERIO_VENDOR_ITE; + s.vendor = SUPERIO_VENDOR_ITE; for (; *i; i++) { - ret.port = *i; - ret.model = probe_id_ite(ret.port); - switch (ret.model >> 8) { + s.port = *i; + s.model = probe_id_ite(s.port); + switch (s.model >> 8) { case 0x82: case 0x86: case 0x87: - msg_pinfo("Found ITE Super I/O, ID 0x%04hx.\n", - ret.model); - return ret; + /* FIXME: Print revision for all models? */ + msg_pdbg("Found ITE Super I/O, ID 0x%04hx on port " + "0x%x\n", s.model, s.port); + register_superio(s); + break; + case 0x85: + msg_pdbg("Found ITE EC, ID 0x%04hx," + "Rev 0x%02x on port 0x%x.\n", + s.model, + sio_read(s.port, CHIP_VER_REG), + s.port); + register_superio(s); + break; } } - /* No good ID found. */ - ret.vendor = SUPERIO_VENDOR_NONE; - ret.port = 0; - ret.model = 0; - return ret; + return; } static uint16_t it87spi_probe(uint16_t port) @@ -113,7 +120,7 @@ msg_pdbg("No IT87* serial flash segment enabled.\n"); exit_conf_mode_ite(port); /* Nothing to do. */ - return 1; + return 0; } msg_pdbg("Serial flash segment 0x%08x-0x%08x %sabled\n", 0xFFFE0000, 0xFFFFFFFF, (tmp & 1 << 1) ? "en" : "dis"); @@ -159,10 +166,7 @@ "port specified.\nPort must be a multiple of " "0x8 and lie between 0x100 and 0xff8.\n"); free(portpos); - /* FIXME: Return failure here once it87spi_common_init() - * can handle the return value sanely. - */ - exit(1); + return 1; } else { flashport = (uint16_t)forced_flashport; msg_pinfo("Forcing serial flash port 0x%04x\n", @@ -177,44 +181,46 @@ if (buses_supported & CHIP_BUSTYPE_SPI) msg_pdbg("Overriding chipset SPI with IT87 SPI.\n"); spi_controller = SPI_CONTROLLER_IT87XX; + /* FIXME: Add the SPI bus or replace the other buses with it? */ buses_supported |= CHIP_BUSTYPE_SPI; return 0; } int init_superio_ite(void) { - if (superio.vendor != SUPERIO_VENDOR_ITE) - return 1; - - switch (superio.model) { - case 0x8705: - return it8705f_write_enable(superio.port); - break; - case 0x8716: - case 0x8718: - case 0x8720: - return it87spi_probe(superio.port); - break; - default: - msg_pdbg("Super I/O ID 0x%04hx is not on the list of flash " - "capable controllers.\n", superio.model); - } - return 1; -} - - -int it87spi_init(void) -{ - int ret; + int i; + int ret = 0; - get_io_perms(); - /* Probe for the Super I/O chip and fill global struct superio. */ - probe_superio(); - ret = init_superio_ite(); - if (!ret) { - buses_supported = CHIP_BUSTYPE_SPI; - } else { - buses_supported = CHIP_BUSTYPE_NONE; + for (i = 0; i < superio_count; i++) { + if (superios[i].vendor != SUPERIO_VENDOR_ITE) + continue; + + switch (superios[i].model) { + case 0x8500: + case 0x8502: + case 0x8510: + case 0x8511: + case 0x8512: + /* FIXME: This should be enabled, but we need a check + * for laptop whitelisting due to the amount of things + * which can go wrong if the EC firmware does not + * implement the interface we want. + */ + //it85xx_spi_init(superios[i]); + break; + case 0x8705: + ret |= it8705f_write_enable(superios[i].port); + break; + case 0x8716: + case 0x8718: + case 0x8720: + ret |= it87spi_probe(superios[i].port); + break; + default: + msg_pdbg("Super I/O ID 0x%04hx is not on the list of " + "flash capable controllers.\n", + superios[i].model); + } } return ret; } @@ -323,10 +329,13 @@ */ int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len) { - int total_size = 1024 * flash->total_size; fast_spi = 0; - if ((programmer == PROGRAMMER_IT87SPI) || (total_size > 512 * 1024)) { + /* FIXME: Check if someone explicitly requested to use IT87 SPI although + * the mainboard does not use IT87 SPI translation. This should be done + * via a programmer parameter for the internal programmer. + */ + if ((flash->total_size * 1024 > 512 * 1024)) { spi_read_chunked(flash, buf, start, len, 3); } else { read_memmapped(flash, buf, start, len); @@ -343,9 +352,11 @@ * so page_size > 256 bytes needs a fallback. * FIXME: Split too big page writes into chunks IT87* can handle instead * of degrading to single-byte program. + * FIXME: Check if someone explicitly requested to use IT87 SPI although + * the mainboard does not use IT87 SPI translation. This should be done + * via a programmer parameter for the internal programmer. */ - if ((programmer == PROGRAMMER_IT87SPI) || - (flash->total_size * 1024 > 512 * 1024) || + if ((flash->total_size * 1024 > 512 * 1024) || (flash->page_size > 256)) { spi_chip_write_1(flash, buf, start, len); } else { Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Fri Apr 15 02:03:37 2011 (r1288) +++ trunk/programmer.h Wed Apr 27 16:34:08 2011 (r1289) @@ -52,11 +52,6 @@ #if CONFIG_ATAHPT == 1 PROGRAMMER_ATAHPT, #endif -#if CONFIG_INTERNAL == 1 -#if defined(__i386__) || defined(__x86_64__) - PROGRAMMER_IT87SPI, -#endif -#endif #if CONFIG_FT2232_SPI == 1 PROGRAMMER_FT2232_SPI, #endif @@ -273,7 +268,8 @@ uint16_t port; uint16_t model; }; -extern struct superio superio; +extern struct superio superios[]; +extern int superio_count; #define SUPERIO_VENDOR_NONE 0x0 #define SUPERIO_VENDOR_ITE 0x1 struct pci_dev *pci_dev_find_filter(struct pci_filter filter); @@ -289,6 +285,7 @@ extern int force_boardenable; extern int force_boardmismatch; void probe_superio(void); +int register_superio(struct superio s); int internal_init(void); int internal_shutdown(void); void internal_chip_writeb(uint8_t val, chipaddr addr); @@ -582,10 +579,8 @@ #endif /* it85spi.c */ -struct superio probe_superio_ite85xx(void); -int it85xx_spi_init(void); +int it85xx_spi_init(struct superio s); int it85xx_shutdown(void); -int it85xx_probe_spi_flash(void); int it85xx_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int it85_spi_read(struct flashchip *flash, uint8_t * buf, int start, int len); @@ -594,9 +589,8 @@ /* it87spi.c */ void enter_conf_mode_ite(uint16_t port); void exit_conf_mode_ite(uint16_t port); -struct superio probe_superio_ite(void); +void probe_superio_ite(void); int init_superio_ite(void); -int it87spi_init(void); int it8716f_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr); int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len);

1 0

motherboard update bios fail (GA-X58A-UD3R (rev. 2.0))
by healthly 27 Apr '11

27 Apr '11

Dear flashrom, I use flashrom to update bios under centos5.5.then there is following output(please help me!) : flashrom v0.9.3-r1288 on Linux 2.6.18-194.26.1.el5xen (x86_64), built with libpci 2.2.3, GCC 4.1.2 20080704 (Red Hat 4.1.2-48), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1414M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 999 us, 10000 myus = 9991 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "X58A-UD3R" DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "X58A-UD3R" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8720. Found chipset "Intel ICH10R", enabling flash write... chipset PCI ID is 8086:3a16, 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x4 0x7fffffff/0x7fffffff FWH IDSEL: 0x5 0x7fffffff/0x7fffffff FWH IDSEL: 0x6 0x7fffffff/0x7fffffff FWH IDSEL: 0x7 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0x464: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x0000 (HSFS) FLOCKDN 0, FDV 0, FDOPSS 0, SCIP 0, BERASE 0, AEL 0, FCERR 0, FDONE 0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00001fff (FREG0: Flash Descriptor) Flash Descriptor region is unused. 0x58: 0x00001fff (FREG1: BIOS) BIOS region is unused. 0x5C: 0x00001fff (FREG2: Management Engine) Management Engine region is unused. 0x60: 0x00001fff (FREG3: Gigabit Ethernet) Gigabit Ethernet region is unused. 0x64: 0x00001fff (FREG4: Platform Data) Platform Data region is unused. 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x04 (SSFS) AEL 0, FCERR 0, FDONE 1, SCIP 0 0x91: 0x007f10 (SSFC) 0x94: 0x5006 (PREOP) 0x96: 0x462b (OPTYPE) 0x98: 0x05ab0302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. No IT87* serial flash segment enabled. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV001BB, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV001BT, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV002BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV002BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV004BB, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV004BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV008BB, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV008BT, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L05PT, 64 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L05PU, 64 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PT, 128 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PU, 128 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PT, 256 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PU, 256 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PT, 512 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PU, 512 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L80P, 1024 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PT, 2048 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PU, 2048 KB: RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L020, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L080, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L016, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L032, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25LQ032, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DQ161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Bright BM29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F25L008A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05T, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10T, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20T, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40T, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80T, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16T, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32T, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64T, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN29F010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address 0xffe00000. Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1635E, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL032A, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL064A, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF010.REMS, 128 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF064C, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF040.REMS, 512 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25LF040A.RES, 512 KB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 RES returned 0x14 0x14. probe_spi_res2: id1 0x14, id2 0x14 Probing for SST SST25VF040B.REMS, 512 KB: REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x27, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x15. Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BB, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25Q80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040/P, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39L040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49F002U/N, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x7d, id2 0x80, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: probe_jedec_common: id1 0x25, id2 0x96, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: probe_jedec_common: id1 0x24, id2 0xdb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Eon unknown Eon SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x15. probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Not unmapping zero size at 0xffffffffffffffff Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. REMS returned c2 14. probe_spi_rems: id1 0xc2, id2 0x14 Not unmapping zero size at 0xffffffffffffffff Flash image seems to be a legacy BIOS. Disabling checks. Reading old flash chip contents... Erasing and writing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff:S, 0x001000-0x001fff:S, 0x002000-0x002fff:S, 0x003000-0x003fff:S, 0x004000-0x004fff:S, 0x005000-0x005fff:S, 0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S, 0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:S, 0x00c000-0x00cfff:S, 0x00d000-0x00dfff:S, 0x00e000-0x00efff:S, 0x00f000-0x00ffff:S, 0x010000-0x010fff:S, 0x011000-0x011fff:S, 0x012000-0x012fff:S, 0x013000-0x013fff:S, 0x014000-0x014fff:S, 0x015000-0x015fff:S, 0x016000-0x016fff:S, 0x017000-0x017fff:S, 0x018000-0x018fff:S, 0x019000-0x019fff:S, 0x01a000-0x01afff:S, 0x01b000-0x01bfff:S, 0x01c000-0x01cfff:S, 0x01d000-0x01dfff:S, 0x01e000-0x01efff:S, 0x01f000-0x01ffff:S, 0x020000-0x020fff:S, 0x021000-0x021fff:S, 0x022000-0x022fff:S, 0x023000-0x023fff:S, 0x024000-0x024fff:S, 0x025000-0x025fff:S, 0x026000-0x026fff:S, 0x027000-0x027fff:S, 0x028000-0x028fff:S, 0x029000-0x029fff:S, 0x02a000-0x02afff:S, 0x02b000-0x02bfff:S, 0x02c000-0x02cfff:S, 0x02d000-0x02dfff:S, 0x02e000-0x02efff:S, 0x02f000-0x02ffff:S, 0x030000-0x030fff:S, 0x031000-0x031fff:S, 0x032000-0x032fff:S, 0x033000-0x033fff:S, 0x034000-0x034fff:S, 0x035000-0x035fff:S, 0x036000-0x036fff:S, 0x037000-0x037fff:S, 0x038000-0x038fff:S, 0x039000-0x039fff:S, 0x03a000-0x03afff:S, 0x03b000-0x03bfff:S, 0x03c000-0x03cfff:S, 0x03d000-0x03dfff:S, 0x03e000-0x03efff:S, 0x03f000-0x03ffff:S, 0x040000-0x040fff:S, 0x041000-0x041fff:S, 0x042000-0x042fff:S, 0x043000-0x043fff:S, 0x044000-0x044fff:S, 0x045000-0x045fff:S, 0x046000-0x046fff:S, 0x047000-0x047fff:S, 0x048000-0x048fff:S, 0x049000-0x049fff:S, 0x04a000-0x04afff:S, 0x04b000-0x04bfff:S, 0x04c000-0x04cfff:S, 0x04d000-0x04dfff:S, 0x04e000-0x04efff:S, 0x04f000-0x04ffff:S, 0x050000-0x050fff:S, 0x051000-0x051fff:S, 0x052000-0x052fff:S, 0x053000-0x053fff:S, 0x054000-0x054fff:S, 0x055000-0x055fff:S, 0x056000-0x056fff:S, 0x057000-0x057fff:S, 0x058000-0x058fff:S, 0x059000-0x059fff:S, 0x05a000-0x05afff:S, 0x05b000-0x05bfff:S, 0x05c000-0x05cfff:S, 0x05d000-0x05dfff:S, 0x05e000-0x05efff:S, 0x05f000-0x05ffff:S, 0x060000-0x060fff:S, 0x061000-0x061fff:S, 0x062000-0x062fff:S, 0x063000-0x063fff:S, 0x064000-0x064fff:S, 0x065000-0x065fff:S, 0x066000-0x066fff:S, 0x067000-0x067fff:S, 0x068000-0x068fff:S, 0x069000-0x069fff:S, 0x06a000-0x06afff:S, 0x06b000-0x06bfff:S, 0x06c000-0x06cfff:S, 0x06d000-0x06dfff:S, 0x06e000-0x06efff:S, 0x06f000-0x06ffff:S, 0x070000-0x070fff:S, 0x071000-0x071fff:S, 0x072000-0x072fff:S, 0x073000-0x073fff:S, 0x074000-0x074fff:S, 0x075000-0x075fff:S, 0x076000-0x076fff:S, 0x077000-0x077fff:S, 0x078000-0x078fff:S, 0x079000-0x079fff:S, 0x07a000-0x07afff:S, 0x07b000-0x07bfff:S, 0x07c000-0x07cfff:S, 0x07d000-0x07dfff:S, 0x07e000-0x07efff:S, 0x07f000-0x07ffff:S, 0x080000-0x080fff:W, 0x081000-0x081fff:W, 0x082000-0x082fff:W, 0x083000-0x083fff:W, 0x084000-0x084fff:W, 0x085000-0x085fff:W, 0x086000-0x086fff:W, 0x087000-0x087fff:W, 0x088000-0x088fff:W, 0x089000-0x089fff:W, 0x08a000-0x08afff:W, 0x08b000-0x08bfff:W, 0x08c000-0x08cfff:W, 0x08d000-0x08dfff:W, 0x08e000-0x08efff:W, 0x08f000-0x08ffff:W, 0x090000-0x090fff:W, 0x091000-0x091fff:W, 0x092000-0x092fff:W, 0x093000-0x093fff:W, 0x094000-0x094fff:W, 0x095000-0x095fff:W, 0x096000-0x096fff:W, 0x097000-0x097fff:W, 0x098000-0x098fff:W, 0x099000-0x099fff:W, 0x09a000-0x09afff:W, 0x09b000-0x09bfff:W, 0x09c000-0x09cfff:W, 0x09d000-0x09dfff:W, 0x09e000-0x09efff:W, 0x09f000-0x09ffff:W, 0x0a0000-0x0a0fff:W, 0x0a1000-0x0a1fff:W, 0x0a2000-0x0a2fff:W, 0x0a3000-0x0a3fff:W, 0x0a4000-0x0a4fff:W, 0x0a5000-0x0a5fff:W, 0x0a6000-0x0a6fff:W, 0x0a7000-0x0a7fff:W, 0x0a8000-0x0a8fff:W, 0x0a9000-0x0a9fff:W, 0x0aa000-0x0aafff:W, 0x0ab000-0x0abfff:W, 0x0ac000-0x0acfff:W, 0x0ad000-0x0adfff:W, 0x0ae000-0x0aefff:W, 0x0af000-0x0affff:W, 0x0b0000-0x0b0fff:W, 0x0b1000-0x0b1fff:W, 0x0b2000-0x0b2fff:W, 0x0b3000-0x0b3fff:W, 0x0b4000-0x0b4fff:W, 0x0b5000-0x0b5fff:W, 0x0b6000-0x0b6fff:W, 0x0b7000-0x0b7fff:W, 0x0b8000-0x0b8fff:W, 0x0b9000-0x0b9fff:W, 0x0ba000-0x0bafff:W, 0x0bb000-0x0bbfff:W, 0x0bc000-0x0bcfff:W, 0x0bd000-0x0bdfff:W, 0x0be000-0x0befff:W, 0x0bf000-0x0bffff:W, 0x0c0000-0x0c0fff:W, 0x0c1000-0x0c1fff:W, 0x0c2000-0x0c2fff:W, 0x0c3000-0x0c3fff:W, 0x0c4000-0x0c4fff:W, 0x0c5000-0x0c5fff:W, 0x0c6000-0x0c6fff:W, 0x0c7000-0x0c7fff:W, 0x0c8000-0x0c8fff:W, 0x0c9000-0x0c9fff:W, 0x0ca000-0x0cafff:W, 0x0cb000-0x0cbfff:W, 0x0cc000-0x0ccfff:W, 0x0cd000-0x0cdfff:W, 0x0ce000-0x0cefff:W, 0x0cf000-0x0cffff:W, 0x0d0000-0x0d0fff:W, 0x0d1000-0x0d1fff:W, 0x0d2000-0x0d2fff:W, 0x0d3000-0x0d3fff:W, 0x0d4000-0x0d4fff:W, 0x0d5000-0x0d5fff:W, 0x0d6000-0x0d6fff:W, 0x0d7000-0x0d7fff:W, 0x0d8000-0x0d8fff:W, 0x0d9000-0x0d9fff:W, 0x0da000-0x0dafff:W, 0x0db000-0x0dbfff:W, 0x0dc000-0x0dcfff:W, 0x0dd000-0x0ddfff:W, 0x0de000-0x0defff:W, 0x0df000-0x0dffff:W, 0x0e0000-0x0e0fff:W, 0x0e1000-0x0e1fff:W, 0x0e2000-0x0e2fff:W, 0x0e3000-0x0e3fff:W, 0x0e4000-0x0e4fff:W, 0x0e5000-0x0e5fff:W, 0x0e6000-0x0e6fff:W, 0x0e7000-0x0e7fff:W, 0x0e8000-0x0e8fff:W, 0x0e9000-0x0e9fff:W, 0x0ea000-0x0eafff:W, 0x0eb000-0x0ebfff:W, 0x0ec000-0x0ecfff:W, 0x0ed000-0x0edfff:W, 0x0ee000-0x0eefff:W, 0x0ef000-0x0effff:W, 0x0f0000-0x0f0fff:W, 0x0f1000-0x0f1fff:W, 0x0f2000-0x0f2fff:W, 0x0f3000-0x0f3fff:W, 0x0f4000-0x0f4fff:W, 0x0f5000-0x0f5fff:W, 0x0f6000-0x0f6fff:W, 0x0f7000-0x0f7fff:W, 0x0f8000-0x0f8fff:W, 0x0f9000-0x0f9fff:W, 0x0fa000-0x0fafff:W, 0x0fb000-0x0fbfff:W, 0x0fc000-0x0fcfff:W, 0x0fd000-0x0fdfff:W, 0x0fe000-0x0fefff:W, 0x0ff000-0x0fffff:E program_opcodes: preop=5006 optype=463b opmenu=05200302c79f0190 on-the-fly OPCODE (0x20) re-programmed, op-pos=2 W, 0x100000-0x100fff:EW, 0x101000-0x101fff:EW, 0x102000-0x102fff:EW, 0x103000-0x103fff:EW, 0x104000-0x104fff:EW, 0x105000-0x105fff:EW, 0x106000-0x106fff:EW, 0x107000-0x107fff:EW, 0x108000-0x108fff:EW, 0x109000-0x109fff:EW, 0x10a000-0x10afff:EW, 0x10b000-0x10bfff:Etimeout, ICH9_REG_SSFS=0x00002401 run OPCODE 0x20 failed spi_block_erase_20 failed during command execution at address 0x10b000 Looking at blockwise erase function 1... trying... 0x000000-0x00ffff:S, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:S, 0x050000-0x05ffff:S, 0x060000-0x06ffff:S, 0x070000-0x07ffff:S, 0x080000-0x08ffff:S, 0x090000-0x09ffff:S, 0x0a0000-0x0affff:S, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:S, 0x0e0000-0x0effff:S, 0x0f0000-0x0fffff:S, 0x100000-0x10ffff:E program_opcodes: preop=5006 optype=463b opmenu=05520302c79f0190 on-the-fly OPCODE (0x52) re-programmed, op-pos=2 ERASE FAILED at 0x00100000! Expected=0xff, Read=0x11, failed byte count from 0x00100000-0x0010ffff: 0xeea9 ERASE FAILED! Looking at blockwise erase function 2... trying... 0x000000-0x00ffff:S, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:S, 0x050000-0x05ffff:S, 0x060000-0x06ffff:S, 0x070000-0x07ffff:S, 0x080000-0x08ffff:S, 0x090000-0x09ffff:S, 0x0a0000-0x0affff:S, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:S, 0x0e0000-0x0effff:S, 0x0f0000-0x0fffff:S, 0x100000-0x10ffff:E program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 on-the-fly OPCODE (0xD8) re-programmed, op-pos=2 timeout, ICH9_REG_SSFS=0x00002401 run OPCODE 0xd8 failed spi_block_erase_d8 failed during command execution at address 0x100000 Error: SCIP never cleared! run OPCODE 0x03 failed Can't read anymore! FAILED! Uh oh. Erase/write failed. Checking if anything changed. Error: SCIP never cleared! run OPCODE 0x03 failed Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! Restoring PCI config space for 00:1f:0 reg 0xdc please help me ,thankyou very much! Best ! healthly

1 0

Here's the fixed patch.
by Brandon Dowdy 27 Apr '11

27 Apr '11

Here's the fixed patch.

2 1

EC kernel interface - kernel feature request [draft]
by Антон Кочков 26 Apr '11

26 Apr '11

Hello! Here is simple draft of possible text for bug in linux, *bsd kernels. "Project flashrom (http://www.flashrom.org) trying to get full and free/open-source solution for BIOS reflashing. It works nice on usual PC systems, and becoming new standard of industry. But on laptops, which have one independend processor core - Embedded Conroller (EC) there is a big trouble to get it working safe, because EC usually always interacting with OS over ACPI. And if flashrom try to flash BIOS, when some of ACPI interrupt calls, it can make laptop dead. " Best regards, Anton Kochkov.

4 3

Flashrom hardware requirements?
by Bernd Blaauw 26 Apr '11

26 Apr '11

dear FlashRom developers, Is there a Wiki page for your project listing minumum hardware requirements and behaviour (errorlevels/errormessages) in case this platform isn't met? I guess FlashRom can only write/erase EEPROM, but identifying and reading is limited to i80586+/8MB/PCI/EEPROM as well? My interest so far lies in Idwer's FlashRom DOS binaries, possibly bundling them with a new FreeDOS distribution, for the sake of identifying and saving BIOS. Graceful errormessages would have my preference above General Protection Faults and the like, if running in situations where processor is too old, not enough RAM, no PCI found or no EEPROM found. with best regards, Bernd Blaauw

1 0

Re: [flashrom] [PATCH] Enable VX855 chipset
by Stefan Tauner 26 Apr '11

26 Apr '11

On Tue, 26 Apr 2011 09:58:30 -0400 John Schmerge <jbschmerge(a)gmail.com> wrote: > Do I specify my own name in the 'signed off' line or yours? you have done all the work, so yours of course... :) please reply to all (i.e. also the mailing list), not only the single person who answered. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[PATCH] ICH SPI paranoid error handling
by Carl-Daniel Hailfinger 24 Apr '11

24 Apr '11

Some people have reported that running flashrom on Ibex Peak (after patching in the PCI ID 0x8086:0x3b02) will not only hang flashrom during the first RES/REMS command issued, it may even cause the machine to lock up or issue a hard reset. We suspect this is because RES/REMS are commands with an address, whereas RDID does not take an address and works fine. Our current ICH SPI code doesn't really follow the datasheets and uses lots of hope instead of error checking in the wrong places. This patch will fail early and fail often if something is odd. As such, merge is not recommended, but running it should definitely generating interesting results on all Intel chipsets with SPI, and especially on Ibex Peak. It probably won't fix the hang, but it should be pretty good at spewing an error before the machine dies. Untested. Highly likely to explode on VIA chipsets which use the same interface but have docs only under NDA. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-ich_spi_fcerr_fcdone_paranoia/chipset_enable.c =================================================================== --- flashrom-ich_spi_fcerr_fcdone_paranoia/chipset_enable.c (Revision 1052) +++ flashrom-ich_spi_fcerr_fcdone_paranoia/chipset_enable.c (Arbeitskopie) @@ -579,8 +579,20 @@ mmio_readl(spibar + 0x80)); msg_pdbg("0x84: 0x%08x (PR4)\n", mmio_readl(spibar + 0x84)); - msg_pdbg("0x90: 0x%08x (SSFS, SSFC)\n", - mmio_readl(spibar + 0x90)); + + tmp = mmio_readl(spibar + 0x90); + msg_pdbg("0x90: 0x%02x (SSFS)\n", tmp & 0xff); + msg_pdbg("AEL %i, ", (tmp >> 4) & 1); + msg_pdbg("FCERR %i, ", (tmp >> 3) & 1); + msg_pdbg("FDONE %i, ", (tmp >> 2) & 1); + msg_pdbg("SCIP %i\n", (tmp >> 0) & 1); + if (tmp & (1 << 3)) { + msg_pdbg("Clearing SSFS.FCERR\n"); + mmio_writeb(1 << 3, spibar + 0x90); + } + tmp >>= 8; + msg_pdbg("0x91: 0x%06x (SSFC)\n", tmp); + msg_pdbg("0x94: 0x%04x (PREOP)\n", mmio_readw(spibar + 0x94)); msg_pdbg("0x96: 0x%04x (OPTYPE)\n", Index: flashrom-ich_spi_fcerr_fcdone_paranoia/ichspi.c =================================================================== --- flashrom-ich_spi_fcerr_fcdone_paranoia/ichspi.c (Revision 1052) +++ flashrom-ich_spi_fcerr_fcdone_paranoia/ichspi.c (Arbeitskopie) @@ -413,6 +413,12 @@ write_cmd = 1; } + /* FIXME: This should be a time-limited while loop. */ + if (REGREAD16(ICH7_REG_SPIS) & SPIS_SCIP) { + msg_perr("Error: Totally unhandled SCIP condition!\n"); + return 1; + } + /* Programm Offset in Flash into FADDR */ REGWRITE32(ICH7_REG_SPIA, (offset & 0x00FFFFFF)); /* SPI addresses are 24 BIT only */ @@ -486,18 +492,22 @@ /* write it */ REGWRITE16(ICH7_REG_SPIC, temp16); - /* wait for cycle complete */ - timeout = 100 * 1000 * 60; // 60s is a looong timeout. - while (((REGREAD16(ICH7_REG_SPIS) & SPIS_CDS) == 0) && --timeout) { + /* Wait for Cycle Done Status or Flash Cycle Error. */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + while (((REGREAD16(ICH7_REG_SPIS) & (SPIS_CDS | SPIS_FCERR)) == 0) && + --timeout) { programmer_delay(10); } if (!timeout) { msg_perr("timeout\n"); + return 1; } /* FIXME: make sure we do not needlessly cause transaction errors. */ - if ((REGREAD16(ICH7_REG_SPIS) & SPIS_FCERR) != 0) { - msg_pdbg("Transaction error!\n"); + if (REGREAD16(ICH7_REG_SPIS) & SPIS_FCERR) { + msg_perr("Transaction error for opcode 0x%02x!\n", + op.opcode); + REGWRITE16(ICH7_REG_SPIS, SPIS_FCERR); return 1; } @@ -532,6 +542,12 @@ write_cmd = 1; } + /* FIXME: This should be a time-limited while loop. */ + if (REGREAD16(ICH9_REG_SSFS) & SSFS_SCIP) { + msg_perr("Error: Totally unhandled SCIP condition!\n"); + return 1; + } + /* Programm Offset in Flash into FADDR */ REGWRITE32(ICH9_REG_FADDR, (offset & 0x00FFFFFF)); /* SPI addresses are 24 BIT only */ @@ -605,18 +621,23 @@ /* write it */ REGWRITE32(ICH9_REG_SSFS, temp32); - /*wait for cycle complete */ - timeout = 100 * 1000 * 60; // 60s is a looong timeout. - while (((REGREAD32(ICH9_REG_SSFS) & SSFS_CDS) == 0) && --timeout) { + /* Wait for Cycle Done Status or Flash Cycle Error. */ + timeout = 100 * 60; /* 60 ms are 9.6 million cycles at 16 MHz. */ + while (((REGREAD32(ICH9_REG_SSFS) & (SSFS_CDS | SSFS_FCERR)) == 0) && + --timeout) { programmer_delay(10); } if (!timeout) { msg_perr("timeout\n"); + return 1; } /* FIXME make sure we do not needlessly cause transaction errors. */ - if ((REGREAD32(ICH9_REG_SSFS) & SSFS_FCERR) != 0) { - msg_pdbg("Transaction error!\n"); + if (REGREAD32(ICH9_REG_SSFS) & SSFS_FCERR) { + msg_perr("Transaction error for opcode 0x%02x!\n", + op.opcode); + //FIXME: Really REGWRITE8? + REGWRITE8(ICH9_REG_SSFS, SSFS_FCERR); return 1; } -- http://www.hailfinger.org/

5 12

Output from flashrom for unrecognised rom
by Antoine Chassagnard 24 Apr '11

24 Apr '11

Hello, err, Mr flashrom :^) I suppose all the info you need is in the file. There might be one more thing: if I try running flashrom from a Xen dom0, it fails, sometimes with a segfault, usually by logging me out. I'm still a Xen newbie, so I don't know whether or not this means anything - I just hope it helps. —-—-—-—-—-—-—-—-—-— Artificial intelligence is no match for natural stupidity.

1 0

Fw: HP DL145 G3
by Stefan Tauner 24 Apr '11

24 Apr '11

hello please reply to the mailing list (too) in the future so that everyone can read your replies. is your bios in a socket? that would be great for further flashrom tests too :) Begin forwarded message: Date: Sat, 23 Apr 2011 23:25:27 +0100 From: Mark Dickie <markd(a)hotdesk.biz> To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Subject: Re: [flashrom] HP DL145 G3 Hi Stefan, I will have to get back to you on that one as I flashed an invalid BIOS to my server right after doing this test. I'm a firm believer in learning through failure :-D I have a USB based programmer on the way and so should have the server back up in a couple of days. Will report back then. Regards, -- Mark Robert Dickie Virtual Desk Limited E markd(a)hotdesk.biz W www.virtual-desk.co.uk T 01315142364 M 07736548602 Skype virtual-desk On 23/04/11 13:21, Stefan Tauner wrote: > On Thu, 21 Apr 2011 20:25:47 +0100 > Mark Dickie <markd(a)hotdesk.biz> wrote: > >> Hello, > Hi! > >> >> Have tested READ on my HP DL145 G3 with the following output:- > thanks for reporting back. > >> flashrom -m hp:dl145_g3 -r bios-backup.rom -V >> flashrom v0.9.1-r946 > ^ thats pretty old btw. > >> Reading flash... done. > have you looked at the contents of bios-backup.rom? does it look like > a valid bios file? > -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

output motherboard asrock n61p-s
by Stefano Banchelli 23 Apr '11

23 Apr '11

flashrom v0.9.2-r1028 on Linux 2.6.35-28-generic (i686), built with libpci 3.0.0, GCC 4.4.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 2 usecs, 1302M loops per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 998 us, 10000 myus = 10015 us, 8 myus = 10 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "N61P-S" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61", enabling flash write... chipset PCI ID is 10de:03e0, This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Guessed flash bus type is SPI Found SMBus device 10de:03eb at 00:01:1 SPI BAR is at 0xfec80000, after clearing low bits BAR is at 0xfec80000 Mapping MCP67 SPI at 0xfec80000, unaligned size 0x544. SPI control is 0x000a, enable=0, idle=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org to help us finish support for your chipset. Thanks. SPI on this chipset is not supported yet. OK. This chipset supports the following protocols: None. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: skipped. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: skipped. Probing for Intel 82802AC, 1024 KB: skipped. Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: skipped. Probing for PMC Pm49FL004, 512 KB: skipped. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: skipped. Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: skipped. Probing for SST SST49LF003A/B, 384 KB: skipped. Probing for SST SST49LF004A/B, 512 KB: skipped. Probing for SST SST49LF004C, 512 KB: skipped. Probing for SST SST49LF008A, 1024 KB: skipped. Probing for SST SST49LF008C, 1024 KB: skipped. Probing for SST SST49LF016C, 2048 KB: skipped. Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: skipped. Probing for ST M50FLW040B, 512 KB: skipped. Probing for ST M50FLW080A, 1024 KB: skipped. Probing for ST M50FLW080B, 1024 KB: skipped. Probing for ST M50FW002, 256 KB: skipped. Probing for ST M50FW016, 2048 KB: skipped. Probing for ST M50FW040, 512 KB: skipped. Probing for ST M50FW080, 1024 KB: skipped. Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS S29C31004T, 512 KB: skipped. Probing for SyncMOS S29C51001T, 128 KB: skipped. Probing for SyncMOS S29C51002T, 256 KB: skipped. Probing for SyncMOS S29C51004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: skipped. Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: skipped. Probing for Winbond W39V080FA, 1024 KB: skipped. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for EON unknown EON SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically.

2 1

HP DL145 G3
by Mark Dickie 23 Apr '11

23 Apr '11

Hello, Have tested READ on my HP DL145 G3 with the following output:- flashrom -m hp:dl145_g3 -r bios-backup.rom -V flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "HP" DMI string system-product-name: "ProLiant DL145 G3" DMI string system-version: " " DMI string baseboard-manufacturer: "NEWISYS" DMI string baseboard-product-name: " " DMI string baseboard-version: "rA4" DMI string chassis-type: "Rack Mount Chassis" Found chipset "Broadcom HT-1000", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Disabling flash write protection for board "HP DL145 G3"... OK. Calibrating delay loop... 530M loops per second, 100 myus = 206 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xf8, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xf8, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Found chip "SST SST49LF080A" (1024 KB, LPC) at physical address 0xfff00000. Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xf8, id2 0x00 Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Reading flash... done. -- Mark Robert Dickie Virtual Desk Limited E markd(a)hotdesk.biz W www.virtual-desk.co.uk T 01315142364 M 07736548602 Skype virtual-desk

2 1

MotherBoard Intel DG45FC - Help
by Márcio Moraes 23 Apr '11

23 Apr '11

Hi, Want to be able to update the ROM, but I can not even save the ROM to a file. The out of the command flashrom -Vr is attached, help-me. Thank you -- --------------------- Cordialmente Márcio Moraes

2 1

[PATCH] add support for Toshiba Satellite P25
by Brandon Dowdy 23 Apr '11

23 Apr '11

This patch adds support for the Toshiba Satellite P25 series. board_enable.c has been reconfigured to fix compilation errors. Thanks to roysjosh, twice11, idwer and others who I forgotten for reverse engineering the board enable and helping me and helping me fix the problems that can be major. If it hasn't been for those people, that laptop shouldn't have been supported by flashrom. :) Signed-off-by: Brandon Dowdy <brandonrd7(a)gmail.com>

3 3

#4: pciutils-dev and Mac OSX
by flashrom 22 Apr '11

22 Apr '11

#4: pciutils-dev and Mac OSX -------------------------------------+------------------------------- Reporter: roufignouf@… | Owner: hailfinger Type: defect | Status: new Priority: major | Milestone: flashrom 0.9.2 Component: flashrom | Version: Keywords: | Dependencies: Patch Status: there is no patch | -------------------------------------+------------------------------- Hi, I try to build flashrom on my macbook but i can't find pciutils-dev for it could you help me ? {{{ Checking for a C compiler... ld: warning: in /System/Library/Frameworks//DirectIO.framework/DirectIO, file was built for i386 which is not the architecture being linked (x86_64) found. Checking for libpci headers... not found. Please install libpci headers (package pciutils-devel). See README for more information. make: *** [pciutils] Error 1 }}} -- Ticket URL: <http://www.flashrom.org/trac/flashrom/ticket/4> flashrom <http://www.flashrom.org/>

1 1

Re: [flashrom] Intel X58 Tylersburg Mainboard
by Idwer Vollering 21 Apr '11

21 Apr '11

2011/4/21 Shailendra Sodhi <shailendra.sodhi(a)endace.com>: > Please find attached patch. > > Signed-off-by:Shailendra Sodhi <shailendra.sodhi(a)endace.com> Thanks. Is this the Tylersburg board in question: http://www.supermicro.com/products/motherboard/QPI/5500/X8DTH-iF.cfm ? Can you edit print.c as well, adding the board name and the forementionned URL ? Once you have done so, I'll ack. Idwer

1 0

[RFC] Can flashrom be configured and built as a programmer only tool
by Bao, Zheng 20 Apr '11

20 Apr '11

Since the Dediprog can work now, if I just want to use flashrom as a programmer interface, I may erase the host BIOS accidently. I think if the flashrom is built without the self-programming feature by some easy settings, I don't have to worry about it. Is it reasonable? Zheng

4 3

Re: [flashrom] Need assistance for using non-coreboot bios image
by Idwer Vollering 20 Apr '11

20 Apr '11

2011/4/20 David Bein <d.bein(a)f5.com>: > Hello Idwer, Hello David, > > Thank you very much for the assistance. I assume > that something like: nvramtool -c 0 will force the > newly booted bios to re-compute the checksum on the cmos? I assume you want to save the current contents with "nvramtool -b cmos_contents.bin" and restore those settings with "nvramtool -B cmos_settings.bin". The manpage can be read (unformatted) in trac: http://tracker.coreboot.org/trac/coreboot/browser/trunk/util/nvramtool/cli/… > > --David >> >> 2011/4/20 David Bein <d.bein(a)f5.com>: >> >>> >>> Hello ... >>> >>> I am very impressed with flashrom. I just used it on a motherboard based >>> on >>> the Lynnfield 3420 chipset and it worked very well and is much faster >>> than >>> the >>> AMI supplied equivalent. >>> >>> I have one problem which is that the very first boot after flashing the >>> bios rom >>> image, the bios complains about a CMOS checksum error and patiently >>> waits for some input. I am assuming others have been here before. What I >>> did >>> next >>> was enter the bios menu and tell it to save changes (none made). All >>> boots >>> after >>> this no longer complain about the CMOS checksum. >>> >>> The reason flashrom is interesting to us (aside from not being >>> restricted >>> by AMI) >>> is for unattended use in customer upgrade situations. Having any upgrade >>> path >>> require a human to type something is a bit of a problem. >>> >>> Any helpful hints will be greatly appreciated. >>> >> >> nvramtool is what you are looking for: http://www.coreboot.org/Nvramtool >> >> >>> >>> Last but not least, thank you to all of you whole have put a lot of >>> effort >>> into >>> this tool for use by coreboot and others. This really validates why open >>> source >>> is needed in the first place. >>> >>> --David >>> >>> >>> >>> _______________________________________________ >>> flashrom mailing list >>> flashrom(a)flashrom.org >>> http://www.flashrom.org/mailman/listinfo/flashrom >>> >>> > >

1 0

Intel X58 Tylersburg Mainboard
by Shailendra Sodhi 20 Apr '11

20 Apr '11

The write operation works on Atmel AT25DF321 chip. Please find attached file that includes flashrom output.

2 1

Need assistance for using non-coreboot bios image
by David Bein 20 Apr '11

20 Apr '11

Hello ... I am very impressed with flashrom. I just used it on a motherboard based on the Lynnfield 3420 chipset and it worked very well and is much faster than the AMI supplied equivalent. I have one problem which is that the very first boot after flashing the bios rom image, the bios complains about a CMOS checksum error and patiently waits for some input. I am assuming others have been here before. What I did next was enter the bios menu and tell it to save changes (none made). All boots after this no longer complain about the CMOS checksum. The reason flashrom is interesting to us (aside from not being restricted by AMI) is for unattended use in customer upgrade situations. Having any upgrade path require a human to type something is a bit of a problem. Any helpful hints will be greatly appreciated. Last but not least, thank you to all of you whole have put a lot of effort into this tool for use by coreboot and others. This really validates why open source is needed in the first place. --David

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom