- flashrom - mail.coreboot.org

[PATCH] ch341a_spi: provide nACT/ACT with CS1/2 for ISP use
by Urja Rannikko 28 Feb '16

28 Feb '16

This allows to drive MCU RST lines or similar with the ch341a during a flashrom run. CS1 is active low and CS2 is active high; note that the tristate state is a weak pullup, thus using CS2 would need an external pull-down. Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> --- ch341a_spi.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/ch341a_spi.c b/ch341a_spi.c index 6eb2804..7e5d577 100644 --- a/ch341a_spi.c +++ b/ch341a_spi.c @@ -303,8 +303,12 @@ static uint8_t swap_byte(uint8_t x) static int32_t enable_pins(bool enable) { uint8_t buf[] = { + /* We provide CS1 as "nACT" and CS2 as "ACT" during operation for ISP + * designs to drive eg. reset lines, meaning CS1 is driven low during + * flashrom run and CS2 high. Note that the tristate state is a weak + * pullup, thus using CS2 needs an external pull-down. */ CH341A_CMD_UIO_STREAM, - CH341A_CMD_UIO_STM_OUT | 0x37, // CS high (all of them), SCK=0, DOUT*=1 + CH341A_CMD_UIO_STM_OUT | (enable ? 0x35 : 0x33), // SCK=0, DOUT*=1 CH341A_CMD_UIO_STM_DIR | (enable ? 0x3F : 0x00), // Interface output enable / disable CH341A_CMD_UIO_STM_END, }; @@ -327,11 +331,11 @@ static void pluck_cs(uint8_t *ptr) stored_delay_us = 0; } *ptr++ = CH341A_CMD_UIO_STREAM; - *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x37; /* deasserted */ + *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x35; /* deasserted */ int i; for (i = 0; i < delay_cnt; i++) - *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x37; /* "delay" */ - *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x36; /* asserted */ + *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x35; /* "delay" */ + *ptr++ = CH341A_CMD_UIO_STM_OUT | 0x34; /* asserted */ *ptr++ = CH341A_CMD_UIO_STM_END; } -- 2.7.1

1 1

Re: [flashrom] [PATCH] Drop non-existing support for nicnatsemi.
by Carl-Daniel Hailfinger 27 Feb '16

27 Feb '16

On 27.02.2016 17:07, Stefan Tauner wrote: > This was meant to support National Semiconductor DP838* network cards > but was never tested successfully. The hardware does not seem to be > available on the market anymore and there was no development for > five years. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Nack, I'd like to push it to some "request for help" section on flashrom.org to find out if someone or some hackerspace has the hardware and is willing to get this finalized. Regards, Carl-Daniel

1 0

[PATCH] Drop non-existing support for nicnatsemi.
by Stefan Tauner 27 Feb '16

27 Feb '16

This was meant to support National Semiconductor DP838* network cards but was never tested successfully. The hardware does not seem to be available on the market anymore and there was no development for five years. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- Makefile | 24 ------------ flashrom.8.tmpl | 9 ++--- flashrom.c | 12 ------ nicnatsemi.c | 115 -------------------------------------------------------- programmer.h | 9 ----- 5 files changed, 3 insertions(+), 166 deletions(-) delete mode 100644 nicnatsemi.c diff --git a/Makefile b/Makefile index 1511eef..7b7d666 100644 --- a/Makefile +++ b/Makefile @@ -249,11 +249,6 @@ UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes else override CONFIG_NICREALTEK = no endif -ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes -else -override CONFIG_NICNATSEMI = no -endif ifeq ($(CONFIG_NICINTEL), yes) UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes else @@ -387,11 +382,6 @@ UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes else override CONFIG_NICREALTEK = no endif -ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes -else -override CONFIG_NICNATSEMI = no -endif ifeq ($(CONFIG_RAYER_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes else @@ -478,11 +468,6 @@ UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes else override CONFIG_NICREALTEK = no endif -ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes -else -override CONFIG_NICNATSEMI = no -endif ifeq ($(CONFIG_NICINTEL), yes) UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes else @@ -606,9 +591,6 @@ CONFIG_DRKAISER ?= yes # Always enable Realtek NICs for now. CONFIG_NICREALTEK ?= yes -# Disable National Semiconductor NICs until support is complete and tested. -CONFIG_NICNATSEMI ?= no - # Always enable Intel NICs for now. CONFIG_NICINTEL ?= yes @@ -860,12 +842,6 @@ PROGRAMMER_OBJS += nicrealtek.o NEED_LIBPCI += CONFIG_NICREALTEK endif -ifeq ($(CONFIG_NICNATSEMI), yes) -FEATURE_CFLAGS += -D'CONFIG_NICNATSEMI=1' -PROGRAMMER_OBJS += nicnatsemi.o -NEED_LIBPCI += CONFIG_NICNATSEMI -endif - ifeq ($(CONFIG_NICINTEL), yes) FEATURE_CFLAGS += -D'CONFIG_NICINTEL=1' PROGRAMMER_OBJS += nicintel.o diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl index 9d8fcc3..2c68351 100644 --- a/flashrom.8.tmpl +++ b/flashrom.8.tmpl @@ -216,9 +216,6 @@ involving any chip access (probe/read/write/...). Currently supported are: .sp .BR "* nicrealtek" " (for flash ROMs on Realtek and SMC 1211 network cards)" .sp -.BR "* nicnatsemi" " (for flash ROMs on National Semiconductor DP838* network \ -cards)" -.sp .BR "* nicintel" " (for parallel flash ROMs on Intel 10/100Mbit network cards) .sp .BR "* gfxnvidia" " (for flash ROMs on NVIDIA graphics cards)" @@ -638,7 +635,7 @@ syntax where .B content is an 8-bit hexadecimal value. .SS -.BR "nic3com" , " nicrealtek" , " nicnatsemi" , " nicintel", " nicintel_eeprom"\ +.BR "nic3com" , " nicrealtek" , " nicintel", " nicintel_eeprom"\ , " nicintel_spi" , " gfxnvidia" , " ogp_spi" , " drkaiser" , " satasii"\ , " satamv" , " atahpt", " atavia ", " atapromise " and " it8212 " programmers .IP @@ -1057,7 +1054,7 @@ access (x86) and MSR access (x86). .B atavia needs PCI configuration space access. .sp -.BR nic3com ", " nicrealtek " and " nicnatsemi " +.BR nic3com " and " nicnatsemi " need PCI configuration space read access and raw I/O port access. .sp .B atahpt @@ -1091,7 +1088,7 @@ need access to the respective USB device via libusb API version 1.0. .B dummy needs no access permissions at all. .sp -.BR internal ", " nic3com ", " nicrealtek ", " nicnatsemi ", " +.BR internal ", " nic3com ", " nicrealtek ", " .BR gfxnvidia ", " drkaiser ", " satasii ", " satamv ", " atahpt ", " atavia " and " atapromise have to be run as superuser/root, and need additional raw access permission. .sp diff --git a/flashrom.c b/flashrom.c index 25e53f2..92e7abc 100644 --- a/flashrom.c +++ b/flashrom.c @@ -110,18 +110,6 @@ const struct programmer_entry programmer_table[] = { }, #endif -#if CONFIG_NICNATSEMI == 1 - { - .name = "nicnatsemi", - .type = PCI, - .devs.dev = nics_natsemi, - .init = nicnatsemi_init, - .map_flash_region = fallback_map, - .unmap_flash_region = fallback_unmap, - .delay = internal_delay, - }, -#endif - #if CONFIG_GFXNVIDIA == 1 { .name = "gfxnvidia", diff --git a/nicnatsemi.c b/nicnatsemi.c deleted file mode 100644 index ce22c94..0000000 --- a/nicnatsemi.c +++ /dev/null @@ -1,115 +0,0 @@ -/* - * This file is part of the flashrom project. - * - * Copyright (C) 2010 Andrew Morgan <ziltro(a)ziltro.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#if defined(__i386__) || defined(__x86_64__) - -#include <stdlib.h> -#include "flash.h" -#include "programmer.h" -#include "hwaccess.h" - -#define PCI_VENDOR_ID_NATSEMI 0x100b - -#define BOOT_ROM_ADDR 0x50 -#define BOOT_ROM_DATA 0x54 - -static uint32_t io_base_addr = 0; -const struct dev_entry nics_natsemi[] = { - {0x100b, 0x0020, NT, "National Semiconductor", "DP83815/DP83816"}, - {0x100b, 0x0022, NT, "National Semiconductor", "DP83820"}, - - {0}, -}; - -static void nicnatsemi_chip_writeb(const struct flashctx *flash, uint8_t val, - chipaddr addr); -static uint8_t nicnatsemi_chip_readb(const struct flashctx *flash, - const chipaddr addr); -static const struct par_master par_master_nicnatsemi = { - .chip_readb = nicnatsemi_chip_readb, - .chip_readw = fallback_chip_readw, - .chip_readl = fallback_chip_readl, - .chip_readn = fallback_chip_readn, - .chip_writeb = nicnatsemi_chip_writeb, - .chip_writew = fallback_chip_writew, - .chip_writel = fallback_chip_writel, - .chip_writen = fallback_chip_writen, -}; - -int nicnatsemi_init(void) -{ - struct pci_dev *dev = NULL; - - if (rget_io_perms()) - return 1; - - dev = pcidev_init(nics_natsemi, PCI_BASE_ADDRESS_0); - if (!dev) - return 1; - - io_base_addr = pcidev_readbar(dev, PCI_BASE_ADDRESS_0); - if (!io_base_addr) - return 1; - - /* The datasheet shows address lines MA0-MA16 in one place and MA0-MA15 - * in another. My NIC has MA16 connected to A16 on the boot ROM socket - * so I'm assuming it is accessible. If not then next line wants to be - * max_rom_decode.parallel = 65536; and the mask in the read/write - * functions below wants to be 0x0000FFFF. - */ - max_rom_decode.parallel = 131072; - register_par_master(&par_master_nicnatsemi, BUS_PARALLEL); - - return 0; -} - -static void nicnatsemi_chip_writeb(const struct flashctx *flash, uint8_t val, - chipaddr addr) -{ - OUTL((uint32_t)addr & 0x0001FFFF, io_base_addr + BOOT_ROM_ADDR); - /* - * The datasheet requires 32 bit accesses to this register, but it seems - * that requirement might only apply if the register is memory mapped. - * Bits 8-31 of this register are apparently don't care, and if this - * register is I/O port mapped, 8 bit accesses to the lowest byte of the - * register seem to work fine. Due to that, we ignore the advice in the - * data sheet. - */ - OUTB(val, io_base_addr + BOOT_ROM_DATA); -} - -static uint8_t nicnatsemi_chip_readb(const struct flashctx *flash, - const chipaddr addr) -{ - OUTL(((uint32_t)addr & 0x0001FFFF), io_base_addr + BOOT_ROM_ADDR); - /* - * The datasheet requires 32 bit accesses to this register, but it seems - * that requirement might only apply if the register is memory mapped. - * Bits 8-31 of this register are apparently don't care, and if this - * register is I/O port mapped, 8 bit accesses to the lowest byte of the - * register seem to work fine. Due to that, we ignore the advice in the - * data sheet. - */ - return INB(io_base_addr + BOOT_ROM_DATA); -} - -#else -#error PCI port I/O access is not supported on this architecture yet. -#endif diff --git a/programmer.h b/programmer.h index bd8e98d..c031ff7 100644 --- a/programmer.h +++ b/programmer.h @@ -39,9 +39,6 @@ enum programmer { #if CONFIG_NICREALTEK == 1 PROGRAMMER_NICREALTEK, #endif -#if CONFIG_NICNATSEMI == 1 - PROGRAMMER_NICNATSEMI, -#endif #if CONFIG_GFXNVIDIA == 1 PROGRAMMER_GFXNVIDIA, #endif @@ -411,12 +408,6 @@ int nicrealtek_init(void); extern const struct dev_entry nics_realtek[]; #endif -/* nicnatsemi.c */ -#if CONFIG_NICNATSEMI == 1 -int nicnatsemi_init(void); -extern const struct dev_entry nics_natsemi[]; -#endif - /* nicintel.c */ #if CONFIG_NICINTEL == 1 int nicintel_init(void); -- Kind regards, Stefan Tauner

1 0

Re: [flashrom] [PATCH] Add support for GD25VQ21B, GD25VQ40C, GD25VQ80C and GD25VQ16C
by Stefan Tauner 27 Feb '16

27 Feb '16

On Fri, 26 Feb 2016 15:52:40 -0800 David Hendricks <dhendrix(a)google.com> wrote: > > +#define GIGADEVICE_GD25VQ21B 0x4212 > > +#define GIGADEVICE_GD25VQ41B 0x4213 /* Same as GD25VQ40C, can be distinguished by SFDP */ > This comment should go in the .c file, above the model_id for the > GD25VQ40C and GD25VQ41B. The only real reason for having flashchips.h is having a nice overview of IDs and relevant information thus that comment is perfectly fine there - it would get lost in the shuffle in the .c file. We have lots of similar comments in the .h file, most prominently the one for the GIGADEVICE_GD25Q128 that the above was copied from ;) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] [PATCH] makefile: allow to disable all default-yes config variables with CONFIG_NOTHING=yes.
by Carl-Daniel Hailfinger 27 Feb '16

27 Feb '16

On 26.02.2016 22:54, Stefan Tauner wrote: > All credit for this should be given to Patrick Georgi (see r1869). > > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Thanks for your patch. Regards, Carl-Daniel

2 1

[commit] r1944 - trunk
by repository service 27 Feb '16

27 Feb '16

Author: stefanct Date: Sat Feb 27 00:51:21 2016 New Revision: 1944 URL: http://flashrom.org/trac/flashrom/changeset/1944 Log: makefile: allow to disable all default-yes config variables with CONFIG_NOTHING=yes. All credit for this should be given to Patrick Georgi (see r1869). Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Thu Feb 25 21:10:26 2016 (r1943) +++ trunk/Makefile Sat Feb 27 00:51:21 2016 (r1944) @@ -642,6 +642,16 @@ # Disable wiki printing by default. It is only useful if you have wiki access. CONFIG_PRINT_WIKI ?= no +# Disable all features if CONFIG_NOTHING=yes is given unless CONFIG_EVERYTHING was also set +ifeq ($(CONFIG_NOTHING), yes) + ifeq ($(CONFIG_EVERYTHING), yes) + $(error Setting CONFIG_NOTHING=yes and CONFIG_EVERYTHING=yes does not make sense) + endif + $(foreach var, $(filter CONFIG_%, $(.VARIABLES)),\ + $(if $(filter yes, $($(var))),\ + $(eval $(var)=no))) +endif + # Enable all features if CONFIG_EVERYTHING=yes is given ifeq ($(CONFIG_EVERYTHING), yes) $(foreach var, $(filter CONFIG_%, $(.VARIABLES)),\

1 0

Re: [flashrom] [PATCH] makefile: allow to disable all default-yes config variables with CONFIG_NOTHING=yes.
by Carl-Daniel Hailfinger 26 Feb '16

26 Feb '16

On 21.02.2016 15:47, Stefan Tauner wrote: > All credit for this should be given to Patrick Georgi (see r1869). > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > --- > Makefile | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/Makefile b/Makefile > index 095a49c..976d7ba 100644 > --- a/Makefile > +++ b/Makefile > @@ -541,6 +541,13 @@ CONFIG_CH341A_SPI ?= yes > # Disable wiki printing by default. It is only useful if you have wiki access. > CONFIG_PRINT_WIKI ?= no > > +# Disable all features if CONFIG_NOTHING=yes is given > +ifeq ($(CONFIG_NOTHING), yes) As per the IRC discussion I'd like to insert an error here if CONFIG_EVERYTHING=yes is set as well. > +$(foreach var, $(filter CONFIG_%, $(.VARIABLES)),\ > + $(if $(filter yes, $($(var))),\ > + $(eval $(var)=no))) > +endif > + > # Enable all features if CONFIG_EVERYTHING=yes is given > ifeq ($(CONFIG_EVERYTHING), yes) > $(foreach var, $(filter CONFIG_%, $(.VARIABLES)),\ Looks good otherwise. Regards, Carl-Daniel

2 1

[PATCH] Partial architecture support for alpha hppa m68k sh
by Carl-Daniel Hailfinger 25 Feb '16

25 Feb '16

Only non-PCI non-rawaccess hardware is supported. No idea if it even compiles. I don't have hardware to test, it's a blind port. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-architecture_support_lite/Makefile =================================================================== --- flashrom-architecture_support_lite/Makefile (Revision 1942) +++ flashrom-architecture_support_lite/Makefile (Arbeitskopie) @@ -414,6 +414,106 @@ endif endif +# Disable all hardware related drivers on architectures with unknown raw access properties. +# Right now those architectures are alpha hppa m68k sh +ifneq ($(ARCH),$(filter $(ARCH),x86 mips ppc arm sparc)) +ifeq ($(CONFIG_INTERNAL), yes) +UNSUPPORTED_FEATURES += CONFIG_INTERNAL=yes +else +override CONFIG_INTERNAL = no +endif +ifeq ($(CONFIG_RAYER_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +else +override CONFIG_RAYER_SPI = no +endif +ifeq ($(CONFIG_PONY_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes +else +override CONFIG_PONY_SPI = no +endif +ifeq ($(CONFIG_NIC3COM), yes) +UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +else +override CONFIG_NIC3COM = no +endif +ifeq ($(CONFIG_GFXNVIDIA), yes) +UNSUPPORTED_FEATURES += CONFIG_GFXNVIDIA=yes +else +override CONFIG_GFXNVIDIA = no +endif +ifeq ($(CONFIG_SATASII), yes) +UNSUPPORTED_FEATURES += CONFIG_SATASII=yes +else +override CONFIG_SATASII = no +endif +ifeq ($(CONFIG_ATAHPT), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +else +override CONFIG_ATAHPT = no +endif +ifeq ($(CONFIG_ATAVIA), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAVIA=yes +else +override CONFIG_ATAVIA = no +endif +ifeq ($(CONFIG_ATAPROMISE), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAPROMISE=yes +else +override CONFIG_ATAPROMISE = no +endif +ifeq ($(CONFIG_MSTARDDC_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_MSTARDDC_SPI=yes +else +override CONFIG_MSTARDDC_SPI = no +endif +ifeq ($(CONFIG_DRKAISER), yes) +UNSUPPORTED_FEATURES += CONFIG_DRKAISER=yes +else +override CONFIG_DRKAISER = no +endif +ifeq ($(CONFIG_NICREALTEK), yes) +UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +else +override CONFIG_NICREALTEK = no +endif +ifeq ($(CONFIG_NICNATSEMI), yes) +UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +else +override CONFIG_NICNATSEMI = no +endif +ifeq ($(CONFIG_NICINTEL), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes +else +override CONFIG_NICINTEL = no +endif +ifeq ($(CONFIG_NICINTEL_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL_SPI=yes +else +override CONFIG_NICINTEL_SPI = no +endif +ifeq ($(CONFIG_NICINTEL_EEPROM), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL_EEPROM=yes +else +override CONFIG_NICINTEL_EEPROM = no +endif +ifeq ($(CONFIG_OGP_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_OGP_SPI=yes +else +override CONFIG_OGP_SPI = no +endif +ifeq ($(CONFIG_SATAMV), yes) +UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +else +override CONFIG_SATAMV = no +endif +ifeq ($(CONFIG_IT8212), yes) +UNSUPPORTED_FEATURES += CONFIG_IT8212=yes +else +override CONFIG_IT8212 = no +endif +endif + ############################################################################### # Flash chip drivers and bus support infrastructure. Index: flashrom-architecture_support_lite/platform.h =================================================================== --- flashrom-architecture_support_lite/platform.h (Revision 1942) +++ flashrom-architecture_support_lite/platform.h (Arbeitskopie) @@ -48,9 +48,21 @@ #elif defined (__sparc__) || defined (__sparc) #define __FLASHROM_ARCH__ "sparc" #define IS_SPARC 1 +#elif defined (__alpha__) + #define __FLASHROM_ARCH__ "alpha" + #define IS_ALPHA 1 +#elif defined (__hppa__) || defined (__hppa) + #define __FLASHROM_ARCH__ "hppa" + #define IS_HPPA 1 +#elif defined (__m68k__) + #define __FLASHROM_ARCH__ "m68k" + #define IS_M68K 1 +#elif defined (__sh__) + #define __FLASHROM_ARCH__ "sh" + #define IS_SH 1 #endif -#if !(IS_X86 || IS_MIPS || IS_PPC || IS_ARM || IS_SPARC) +#if !(IS_X86 || IS_MIPS || IS_PPC || IS_ARM || IS_SPARC || IS_ALPHA || IS_HPPA || IS_M68K || IS_SH) #error Unknown architecture #endif

2 4

[commit] r1943 - trunk
by repository service 25 Feb '16

25 Feb '16

Author: hailfinger Date: Thu Feb 25 21:10:26 2016 New Revision: 1943 URL: http://flashrom.org/trac/flashrom/changeset/1943 Log: Partial architecture support for alpha hppa m68k sh s390 Only hardware not needing raw access (PCI, memory, port I/O) is supported. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Modified: trunk/Makefile trunk/platform.h Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Feb 22 09:59:27 2016 (r1942) +++ trunk/Makefile Thu Feb 25 21:10:26 2016 (r1943) @@ -414,6 +414,107 @@ endif endif +# Disable all drivers needing raw access (memory, PCI, port I/O) on +# architectures with unknown raw access properties. +# Right now those architectures are alpha hppa m68k sh s390 +ifneq ($(ARCH),$(filter $(ARCH),x86 mips ppc arm sparc)) +ifeq ($(CONFIG_INTERNAL), yes) +UNSUPPORTED_FEATURES += CONFIG_INTERNAL=yes +else +override CONFIG_INTERNAL = no +endif +ifeq ($(CONFIG_RAYER_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +else +override CONFIG_RAYER_SPI = no +endif +ifeq ($(CONFIG_PONY_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes +else +override CONFIG_PONY_SPI = no +endif +ifeq ($(CONFIG_NIC3COM), yes) +UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +else +override CONFIG_NIC3COM = no +endif +ifeq ($(CONFIG_GFXNVIDIA), yes) +UNSUPPORTED_FEATURES += CONFIG_GFXNVIDIA=yes +else +override CONFIG_GFXNVIDIA = no +endif +ifeq ($(CONFIG_SATASII), yes) +UNSUPPORTED_FEATURES += CONFIG_SATASII=yes +else +override CONFIG_SATASII = no +endif +ifeq ($(CONFIG_ATAHPT), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +else +override CONFIG_ATAHPT = no +endif +ifeq ($(CONFIG_ATAVIA), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAVIA=yes +else +override CONFIG_ATAVIA = no +endif +ifeq ($(CONFIG_ATAPROMISE), yes) +UNSUPPORTED_FEATURES += CONFIG_ATAPROMISE=yes +else +override CONFIG_ATAPROMISE = no +endif +ifeq ($(CONFIG_MSTARDDC_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_MSTARDDC_SPI=yes +else +override CONFIG_MSTARDDC_SPI = no +endif +ifeq ($(CONFIG_DRKAISER), yes) +UNSUPPORTED_FEATURES += CONFIG_DRKAISER=yes +else +override CONFIG_DRKAISER = no +endif +ifeq ($(CONFIG_NICREALTEK), yes) +UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +else +override CONFIG_NICREALTEK = no +endif +ifeq ($(CONFIG_NICNATSEMI), yes) +UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +else +override CONFIG_NICNATSEMI = no +endif +ifeq ($(CONFIG_NICINTEL), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes +else +override CONFIG_NICINTEL = no +endif +ifeq ($(CONFIG_NICINTEL_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL_SPI=yes +else +override CONFIG_NICINTEL_SPI = no +endif +ifeq ($(CONFIG_NICINTEL_EEPROM), yes) +UNSUPPORTED_FEATURES += CONFIG_NICINTEL_EEPROM=yes +else +override CONFIG_NICINTEL_EEPROM = no +endif +ifeq ($(CONFIG_OGP_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_OGP_SPI=yes +else +override CONFIG_OGP_SPI = no +endif +ifeq ($(CONFIG_SATAMV), yes) +UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +else +override CONFIG_SATAMV = no +endif +ifeq ($(CONFIG_IT8212), yes) +UNSUPPORTED_FEATURES += CONFIG_IT8212=yes +else +override CONFIG_IT8212 = no +endif +endif + ############################################################################### # Flash chip drivers and bus support infrastructure. Modified: trunk/platform.h ============================================================================== --- trunk/platform.h Mon Feb 22 09:59:27 2016 (r1942) +++ trunk/platform.h Thu Feb 25 21:10:26 2016 (r1943) @@ -48,9 +48,24 @@ #elif defined (__sparc__) || defined (__sparc) #define __FLASHROM_ARCH__ "sparc" #define IS_SPARC 1 +#elif defined (__alpha__) + #define __FLASHROM_ARCH__ "alpha" + #define IS_ALPHA 1 +#elif defined (__hppa__) || defined (__hppa) + #define __FLASHROM_ARCH__ "hppa" + #define IS_HPPA 1 +#elif defined (__m68k__) + #define __FLASHROM_ARCH__ "m68k" + #define IS_M68K 1 +#elif defined (__sh__) + #define __FLASHROM_ARCH__ "sh" + #define IS_SH 1 +#elif defined(__s390__) || defined(__s390x__) || defined(__zarch__) + #define __FLASHROM_ARCH__ "s390" + #define IS_S390 1 #endif -#if !(IS_X86 || IS_MIPS || IS_PPC || IS_ARM || IS_SPARC) +#if !(IS_X86 || IS_MIPS || IS_PPC || IS_ARM || IS_SPARC || IS_ALPHA || IS_HPPA || IS_M68K || IS_SH || IS_S390) #error Unknown architecture #endif

1 0

W836xx: Intel HM76: flashrom -V
by Micah Lee 24 Feb '16

24 Feb '16

Hey, I'm having trouble dumping my firmware image. I built the latest version of flashrom from source on an ubuntu live USB stick. The laptop is a Lenovo IdeaPad S210 Touch. Here's my output: $ sudo flashrom -V -p internal flashrom v0.9.8-r1888 on Linux 4.2.0-16-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.3.1, GCC 5.2.1 20151010, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 927M loops per second, 10 myus = 10 us, 100 myus = 98 us, 1000 myus = 982 us, 10000 myus = 9786 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. No DMI table found. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 85. Please send the output of "flashrom -V -p internal" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE EC, ID 0x8528, Rev 0x09 on port 0x4e. Found chipset "Intel HM76" with PCI ID 8086:1e59. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc20: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: enabled (A16(+) inverted) 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI Read Configuration: prefetching disabled, caching enabled, BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled SPIBAR = 0x00007f93d00c8000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x0004 (HSFC) HSFC: FGO=0, FCYCLE=2, FDBC=0, SME=0 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x03ff0180 FREG1: BIOS region (0x00180000-0x003fffff) is read-write. 0x5C: 0x017f0001 FREG2: Warning: Management Engine region (0x00001000-0x0017ffff) is locked. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see http://flashrom.org/ME for details. 0x74: 0x83ff0370 PR0: Warning: 0x00370000-0x003fffff is read-only. 0x78: 0x83210182 PR1: Warning: 0x00182000-0x00321fff is read-only. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf84200 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=2, SME=0, SCF=0 0x94: 0x0606 (PREOP) 0x96: 0xf27c (OPTYPE) 0x98: 0x0102209f (OPMENU) 0x9C: 0x00000503 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xD0: 0x00000000 (FPB) OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DL081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DL161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F512, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512A, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25F1024(A), 128 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F2048, 256 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F4096, 512 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB321E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ESMT F25L32PA, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX23L1654, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX23L3254, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX23L6454, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX23L12854, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L2005(C)/MX25L2006E, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L4005(A/C)/MX25L4006E, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L8005/MX25L8006E/MX25L8008E/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605A/MX25L1606E/MX25L1608E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3206E/MX25L3208E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3273E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6405D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6436E/MX25L6445E/MX25L6465E/MX25L6473E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L12805D, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L12835F/MX25L12845E/MX25L12865E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25U12835F, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix MX25L6495F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV512(A), 64 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LE25FW106, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW406A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FU406B, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo LE25FW418A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW806, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW808, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL132K, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL164K, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL127S-64kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL127S-256kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL128P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL128P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL128S......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL128S......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL129P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Spansion S25FL129P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25LF020A, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080(A), 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF512(A), 64 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF010(A), 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020B, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST SST25WF080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q40.V, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Found Winbond flash chip "W25Q32.V" (4096 kB, SPI) mapped at physical address 0x00000000ffc00000. Chip status register is 0x00. Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4016 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x82, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x82, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x82, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x00, id2 0xeb, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xf0, id2 0x1b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x82, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xf0, id2 0x1b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x82, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x20, id2 0x00, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q32.V" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). No operations were specified. Restoring MMIO space at 0x7f93d00cb8a0 Restoring PCI config space for 00:1f:0 reg 0xdc

1 1

Re: [flashrom] [PATCH] dediprog: use ordinary USB devs array.
by Carl-Daniel Hailfinger 23 Feb '16

23 Feb '16

On 21.02.2016 21:22, Stefan Tauner wrote: > Even though there is currently only one USB device ID in the wild using our > standard way to define the devices creates nicer output for -L and -z. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel

2 1

Re: [flashrom] [PATCH] pickit2_spi: use ordinary USB devs array.
by Carl-Daniel Hailfinger 23 Feb '16

23 Feb '16

On 21.02.2016 21:41, Stefan Tauner wrote: > Even though there is currently only one USB device ID in the wild using our > standard way to define the devices creates nicer output for -L and -z. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel

2 1

[commit] r1942 - trunk
by repository service 22 Feb '16

22 Feb '16

Author: stefanct Date: Mon Feb 22 09:59:27 2016 New Revision: 1942 URL: http://flashrom.org/trac/flashrom/changeset/1942 Log: dediprog: use ordinary USB devs array. Even though there is currently only one USB device ID in the wild using our standard way to define the devices creates nicer output for -L and -z. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/dediprog.c trunk/flashrom.c trunk/programmer.h Modified: trunk/dediprog.c ============================================================================== --- trunk/dediprog.c Mon Feb 22 09:59:15 2016 (r1941) +++ trunk/dediprog.c Mon Feb 22 09:59:27 2016 (r1942) @@ -143,6 +143,11 @@ LEAVE_STANDALONE_MODE = 1, }; +const struct dev_entry devs_dediprog[] = { + {0x0483, 0xDADA, OK, "Dediprog", "SF100/SF600"}, + + {0}, +}; static int dediprog_firmwareversion = FIRMWARE_VERSION(0, 0, 0); enum dediprog_devtype dediprog_devicetype = DEV_UNKNOWN; @@ -1019,7 +1024,10 @@ msg_perr("Could not initialize libusb!\n"); return 1; } - dediprog_handle = get_device_by_vid_pid_number(0x0483, 0xdada, (unsigned int) usedevice); + + const uint16_t vid = devs_dediprog[0].vendor_id; + const uint16_t pid = devs_dediprog[0].device_id; + dediprog_handle = get_device_by_vid_pid_number(vid, pid, (unsigned int) usedevice); if (!dediprog_handle) { msg_perr("Could not find a Dediprog programmer on USB.\n"); libusb_exit(usb_ctx); Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Mon Feb 22 09:59:15 2016 (r1941) +++ trunk/flashrom.c Mon Feb 22 09:59:27 2016 (r1942) @@ -247,9 +247,8 @@ #if CONFIG_DEDIPROG == 1 { .name = "dediprog", - .type = OTHER, - /* FIXME */ - .devs.note = "Dediprog SF100\n", + .type = USB, + .devs.dev = devs_dediprog, .init = dediprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Mon Feb 22 09:59:15 2016 (r1941) +++ trunk/programmer.h Mon Feb 22 09:59:27 2016 (r1942) @@ -528,6 +528,7 @@ /* dediprog.c */ #if CONFIG_DEDIPROG == 1 int dediprog_init(void); +extern const struct dev_entry devs_dediprog[]; #endif /* ch341a_spi.c */

1 0

[commit] r1941 - trunk
by repository service 22 Feb '16

22 Feb '16

Author: stefanct Date: Mon Feb 22 09:59:15 2016 New Revision: 1941 URL: http://flashrom.org/trac/flashrom/changeset/1941 Log: pickit2_spi: use ordinary USB devs array. Even though there is currently only one USB device ID in the wild using our standard way to define the devices creates nicer output for -L and -z. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/flashrom.c trunk/pickit2_spi.c trunk/programmer.h Modified: trunk/flashrom.c ============================================================================== --- trunk/flashrom.c Sun Feb 21 19:25:15 2016 (r1940) +++ trunk/flashrom.c Mon Feb 22 09:59:15 2016 (r1941) @@ -382,9 +382,8 @@ #if CONFIG_PICKIT2_SPI == 1 { .name = "pickit2_spi", - .type = OTHER, - /* FIXME */ - .devs.note = "Microchip PICkit2\n", + .type = USB, + .devs.dev = devs_pickit2_spi, .init = pickit2_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, Modified: trunk/pickit2_spi.c ============================================================================== --- trunk/pickit2_spi.c Sun Feb 21 19:25:15 2016 (r1940) +++ trunk/pickit2_spi.c Mon Feb 22 09:59:15 2016 (r1941) @@ -55,6 +55,12 @@ #include "programmer.h" #include "spi.h" +const struct dev_entry devs_pickit2_spi[] = { + {0x04D8, 0x0033, OK, "Microchip", "PICkit 2"}, + + {} +}; + static usb_dev_handle *pickit2_handle; /* Default USB transaction timeout in ms */ @@ -64,9 +70,6 @@ #define ENDPOINT_OUT 0x01 #define ENDPOINT_IN 0x81 -#define PICKIT2_VID 0x04D8 -#define PICKIT2_PID 0x0033 - #define CMD_GET_VERSION 0x76 #define CMD_SET_VDD 0xA0 #define CMD_SET_VPP 0xA1 @@ -448,7 +451,9 @@ usb_init(); (void)usb_find_busses(); (void)usb_find_devices(); - struct usb_device *dev = get_device_by_vid_pid(PICKIT2_VID, PICKIT2_PID, usedevice); + const uint16_t vid = devs_pickit2_spi[0].vendor_id; + const uint16_t pid = devs_pickit2_spi[0].device_id; + struct usb_device *dev = get_device_by_vid_pid(vid, pid, usedevice); if (dev == NULL) { msg_perr("Could not find a PICkit2 on USB!\n"); return 1; Modified: trunk/programmer.h ============================================================================== --- trunk/programmer.h Sun Feb 21 19:25:15 2016 (r1940) +++ trunk/programmer.h Mon Feb 22 09:59:15 2016 (r1941) @@ -499,6 +499,7 @@ /* pickit2_spi.c */ #if CONFIG_PICKIT2_SPI == 1 int pickit2_spi_init(void); +extern const struct dev_entry devs_pickit2_spi[]; #endif /* rayer_spi.c */

1 0

Re: [flashrom] about GIGABYTE GA-X58A-UD3R board
by Stefan Tauner 22 Feb '16

22 Feb '16

On Fri, 19 Feb 2016 13:25:57 +0900 げんまいこ <gennmaiko(a)gmail.com> wrote: > Hi, > I have read this article > http://www.coreboot.org/FAQ#Will_coreboot_work_on_my_machine.3F > And I will send my Step1-6. Hi, the wiki points you to the coreboot mailing list but you sent your mail to the flashrom mailing list instead... -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

W836xx: Biostar A68N-2100: flashrom -V
by Moritz Wilhelmy 22 Feb '16

22 Feb '16

Just in case nobody posted flashrom -V output for this board yet, please see below. Cheers, Moritz ____ flashrom v0.9.7-r1852 on Linux 4.3.0-0.bpo.1-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.1, GCC 4.9.2, little endian Command line (3 args): flashrom -V -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 332M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10007 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Desktop" DMI string system-manufacturer: "BIOSTAR Group" DMI string system-product-name: "A68N-2100" DMI string system-version: " " DMI string baseboard-manufacturer: "BIOSTAR Group" DMI string baseboard-product-name: "A68N-2100" DMI string baseboard-version: " " Found ITE Super I/O, ID 0x8728 on port 0x2e Found chipset "AMD FCH" with PCI ID 1022:780e. Enabling flash write... SPI base address is at 0xfec10000 Yangtze detected. SpiRomEnable=1, RouteTpm2Sp=0, PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1 (0x6fcc2305) SpiArbEnable=1, IllegalAccess=0, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=7, SpiBusy=0 Using SPI_CS0 GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK SpiReadMode=Fast Read (7) Setting read mode to "Normal (up to 66 MHz)" succeeded. UseSpi100 is enabled NormSpeedNew is 33 MHz FastSpeedNew is 66 MHz AltSpeedNew is 16.5 MHz TpmSpeedNew is 16.5 MHz Setting SPI clock to 16.5 MHz (0x3). IMC is not active. ROM strap override is not active OK. No IT87* serial flash segment enabled. The following protocols are supported: LPC, FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DL081, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DL161, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25F512, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512A, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25F1024(A), 128 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F2048, 256 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25F4096, 512 kB: probe_spi_at25f: id1 0xff, id2 0xff Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB321E, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for ESMT F25L32PA, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Found GigaDevice flash chip "GD25Q32(B)" (4096 kB, SPI) mapped at physical address 0x00000000ffc00000. Chip status register is 0x00. Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set Chip status register: Block Protect 4 (BP4) is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX23L1654, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX23L3254, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX23L6454, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX23L12854, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L2005(C), 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L4005(A/C), 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L8005/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1605A/MX25L1606E, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L3206E, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L3273E, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L6405(D), 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L6406E/MX25L6436E, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L6445E/MX25L6473E, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25L12805(D), 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix MX25U12835F, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LV512(A), 64 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for PMC Pm25LV010, 128 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Sanyo LE25FW106, 128 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Sanyo LE25FW406A, 512 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Sanyo LE25FU406B, 512 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Sanyo LE25FW418A, 512 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Sanyo LE25FW806, 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Sanyo LE25FW808, 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL132K, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL164K, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL128P......0, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL128P......1, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL128S......0, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL128S......1, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL129P......0, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Spansion S25FL129P......1, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25LF020A, 256 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25LF080(A), 1024 kB: probe_spi_res2: id1 0x15, id2 0x15 Probing for SST SST25VF512(A), 64 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25VF010(A), 128 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25VF020, 256 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25VF020B, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST SST25WF080, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q40.V, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc8, id2 0x4016 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc8, id2 0x15 Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xd3, id2 0xd2, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xd3, id2 0xd2, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xd3, id2 0xd2, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xd3, id2 0xd2, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xfc, id2 0x8b, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found GigaDevice flash chip "GD25Q32(B)" (4096 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). No operations were specified. Restoring MMIO space at 0x7fa8da06f022 Restoring MMIO space at 0x7fa8da06f000

1 0

Re: [flashrom] BIOS update using flashrom on an UEFI system
by Lakesh_Sharma＠DELL.com 22 Feb '16

22 Feb '16

layout file option is being explored by our team. regards lakesh ________________________________________ From: David Hendricks [dhendrix(a)google.com] Sent: Thursday, February 18, 2016 2:57 PM To: Sharma, Lakesh Cc: flashrom Subject: Re: [flashrom] BIOS update using flashrom on an UEFI system Hi Lakesh, Did you ever find a solution for this? Probably the quickest solution is to figure out where the config data resides and write to the regions around it using a layout file. It's an interesting problem that I suspect we'll see more often in the future, not just with UEFI. Storage of config data on the firmware ROM is becoming more common, and the firmware update utility of choice needs to become more aware of what portions of the ROM are safe to overwrite. For ChromeOS platforms, we added a blob that maps the ROM content (flashmap, or fmap for short) so that our update scripts know which regions of the ROM to target when updating. I'm not sure what the best way to do this for other systems, though. AFAIK this is all vendor-specific. On Tue, Feb 9, 2016 at 6:21 PM, <Lakesh_Sharma(a)dell.com<mailto:Lakesh_Sharma@dell.com>> wrote: In an UEFI based system (x86_64, Rangeley cpu), the bios bootup option shows each UEFI partition. Where as in legacy bios mode, the bios bootup menu would show just SSD, USB etc. In case of UEFI system, the boot-order, boot-current etc (i.e. UEFI config data) is stored in bios area ? When we update bios using flashrom, we are seeing that the UEFI config data is getting lost/over-written. Because of which, bios does not know that it is running on uefi system and probably tries to invoke grub using legacy way, which hangs. How can we instruct flashrom to not over-write UEFI config data in bios area. regards lakesh _______________________________________________ flashrom mailing list flashrom(a)flashrom.org<mailto:flashrom@flashrom.org> http://www.flashrom.org/mailman/listinfo/flashrom -- David Hendricks (dhendrix) Systems Software Engineer, Google Inc.

1 0

[PATCH] pickit2_spi: use ordinary USB devs array.
by Stefan Tauner 21 Feb '16

21 Feb '16

Even though there is currently only one USB device ID in the wild using our standard way to define the devices creates nicer output for -L and -z. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- flashrom.c | 5 ++--- pickit2_spi.c | 13 +++++++++---- programmer.h | 1 + 3 files changed, 12 insertions(+), 7 deletions(-) diff --git a/flashrom.c b/flashrom.c index 7bdfb73..d671003 100644 --- a/flashrom.c +++ b/flashrom.c @@ -382,9 +382,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_PICKIT2_SPI == 1 { .name = "pickit2_spi", - .type = OTHER, - /* FIXME */ - .devs.note = "Microchip PICkit2\n", + .type = USB, + .devs.dev = devs_pickit2_spi, .init = pickit2_spi_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, diff --git a/pickit2_spi.c b/pickit2_spi.c index e5f7bed..f1f60a2 100644 --- a/pickit2_spi.c +++ b/pickit2_spi.c @@ -55,6 +55,12 @@ #include "programmer.h" #include "spi.h" +const struct dev_entry devs_pickit2_spi[] = { + {0x04D8, 0x0033, OK, "Microchip", "PICkit 2"}, + + {} +}; + static usb_dev_handle *pickit2_handle; /* Default USB transaction timeout in ms */ @@ -64,9 +70,6 @@ static usb_dev_handle *pickit2_handle; #define ENDPOINT_OUT 0x01 #define ENDPOINT_IN 0x81 -#define PICKIT2_VID 0x04D8 -#define PICKIT2_PID 0x0033 - #define CMD_GET_VERSION 0x76 #define CMD_SET_VDD 0xA0 #define CMD_SET_VPP 0xA1 @@ -448,7 +451,9 @@ int pickit2_spi_init(void) usb_init(); (void)usb_find_busses(); (void)usb_find_devices(); - struct usb_device *dev = get_device_by_vid_pid(PICKIT2_VID, PICKIT2_PID, usedevice); + const uint16_t vid = devs_pickit2_spi[0].vendor_id; + const uint16_t pid = devs_pickit2_spi[0].device_id; + struct usb_device *dev = get_device_by_vid_pid(vid, pid, usedevice); if (dev == NULL) { msg_perr("Could not find a PICkit2 on USB!\n"); return 1; diff --git a/programmer.h b/programmer.h index 301f3ff..9a880d7 100644 --- a/programmer.h +++ b/programmer.h @@ -499,6 +499,7 @@ int mstarddc_spi_init(void); /* pickit2_spi.c */ #if CONFIG_PICKIT2_SPI == 1 int pickit2_spi_init(void); +extern const struct dev_entry devs_pickit2_spi[]; #endif /* rayer_spi.c */ -- Kind regards, Stefan Tauner

1 0

[PATCH] dediprog: use ordinary USB devs array.
by Stefan Tauner 21 Feb '16

21 Feb '16

Even though there is currently only one USB device ID in the wild using our standard way to define the devices creates nicer output for -L and -z. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- dediprog.c | 10 +++++++++- flashrom.c | 5 ++--- programmer.h | 1 + 3 files changed, 12 insertions(+), 4 deletions(-) diff --git a/dediprog.c b/dediprog.c index 6a9b9ae..019de46 100644 --- a/dediprog.c +++ b/dediprog.c @@ -143,6 +143,11 @@ enum dediprog_standalone_mode { LEAVE_STANDALONE_MODE = 1, }; +const struct dev_entry devs_dediprog[] = { + {0x0483, 0xDADA, OK, "Dediprog", "SF100/SF600"}, + + {0}, +}; static int dediprog_firmwareversion = FIRMWARE_VERSION(0, 0, 0); enum dediprog_devtype dediprog_devicetype = DEV_UNKNOWN; @@ -1019,7 +1024,10 @@ int dediprog_init(void) msg_perr("Could not initialize libusb!\n"); return 1; } - dediprog_handle = get_device_by_vid_pid_number(0x0483, 0xdada, (unsigned int) usedevice); + + const uint16_t vid = devs_dediprog[0].vendor_id; + const uint16_t pid = devs_dediprog[0].device_id; + dediprog_handle = get_device_by_vid_pid_number(vid, pid, (unsigned int) usedevice); if (!dediprog_handle) { msg_perr("Could not find a Dediprog programmer on USB.\n"); libusb_exit(usb_ctx); diff --git a/flashrom.c b/flashrom.c index 7bdfb73..6ca633e 100644 --- a/flashrom.c +++ b/flashrom.c @@ -247,9 +247,8 @@ const struct programmer_entry programmer_table[] = { #if CONFIG_DEDIPROG == 1 { .name = "dediprog", - .type = OTHER, - /* FIXME */ - .devs.note = "Dediprog SF100\n", + .type = USB, + .devs.dev = devs_dediprog, .init = dediprog_init, .map_flash_region = fallback_map, .unmap_flash_region = fallback_unmap, diff --git a/programmer.h b/programmer.h index 301f3ff..61702a4 100644 --- a/programmer.h +++ b/programmer.h @@ -527,6 +527,7 @@ int linux_spi_init(void); /* dediprog.c */ #if CONFIG_DEDIPROG == 1 int dediprog_init(void); +extern const struct dev_entry devs_dediprog[]; #endif /* ch341a_spi.c */ -- Kind regards, Stefan Tauner

1 0

[commit] r1940 - tags/0.9.9-rc1
by repository service 21 Feb '16

21 Feb '16

Author: stefanct Date: Sun Feb 21 19:25:15 2016 New Revision: 1940 URL: http://flashrom.org/trac/flashrom/changeset/1940 Log: Tag flashrom 0.9.9-rc1. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Urja Rannikko <urjaman(a)gmail.com> Added: tags/0.9.9-rc1/ - copied from r1939, trunk/

1 0

[commit] r1939 - trunk
by repository service 21 Feb '16

21 Feb '16

Author: stefanct Date: Sun Feb 21 19:17:14 2016 New Revision: 1939 URL: http://flashrom.org/trac/flashrom/changeset/1939 Log: Increase version number to 0.9.9-rc1. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Urja Rannikko <urjaman(a)gmail.com> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sun Feb 21 12:18:24 2016 (r1938) +++ trunk/Makefile Sun Feb 21 19:17:14 2016 (r1939) @@ -437,7 +437,7 @@ # will not require subversion. The downloadable snapshots are already exported. SVNVERSION := $(shell ./util/getrevision.sh -u 2>/dev/null ) -RELEASE := 0.9.8 +RELEASE := 0.9.9-rc1 VERSION := $(RELEASE)-$(SVNVERSION) RELEASENAME ?= $(VERSION)

1 0

Re: [flashrom] [PATCH 3/3] serprog: allow to omit specifying a baud rate.
by Stefan Tauner 21 Feb '16

21 Feb '16

On Sun, 28 Jun 2015 03:56:52 +0200 Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> wrote: > On USB-based serial connections (VCP) the requested baud rate usually > does not matter (much). Remove the arbitrary restriction and use whatever > default values the OS/hardware provides. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Urja Rannikko <urjaman(a)gmail.com> and committed already in r1907 some time ago. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] [PATCH 2/3] serprog: ignore failures when setting serial port options.
by Stefan Tauner 21 Feb '16

21 Feb '16

On Sun, 28 Jun 2015 03:56:51 +0200 Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> wrote: > There is no good reason to abort earlier just because some options did > not stick. This should improve compatibility without negative effects. If > communication is affected by the missing flag(s) then we abort later > anyway. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Urja Rannikko <urjaman(a)gmail.com> and committed already in r1906 some time ago. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] [PATCH 1/3] serprog: clear NDELAY flag only once after opening the port.
by Stefan Tauner 21 Feb '16

21 Feb '16

On Sun, 28 Jun 2015 03:56:50 +0200 Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> wrote: > Change sp_openserport() to directly clear the O_NONBLOCK flag that > is potentially set by opening the device with O_NDELAY instead of > clearing ALL flags in serialport_config() unconditionally. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Urja Rannikko <urjaman(a)gmail.com> and committed already in r1905 some time ago. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Support for Intel I350 card.
by Grzegorz Hetman 21 Feb '16

21 Feb '16

Hello ;) I have a card called: 05:00.0 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01) 05:00.1 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01) 05:00.2 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01) 05:00.3 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01) I update nicintel_spi.c to match product ID but when I try to probe it, flashroom freeze after a while: ./flashrom -VVV -p nicintel_spi:pci='05:00.0' -o probe.log flashrom v0.9.8-r1916 on Linux 4.2.2-coreos-r1 (x86_64) flashrom is free software, get the source code at https://flashrom.org flashrom was built with libpci 3.2.1, GCC 4.8.4, little endian Command line (5 args): ./flashrom -VVV -p nicintel_spi:pci=05:00.0 -o probe.log Calibrating delay loop... OS timer resolution is 1 usecs, 1224M loops per second, 10 myus = 10 us, 100 myus = 102 us, 1000 myus = 1028 us, 10000 myus = 9996 us, 4 myus = 16 us, OK. Initializing nicintel_spi programmer Found "Intel I350 Gigabit Network Connection (rev 01)" (8086:1521, BDF 05:00.0). === This PCI device is UNTESTED. Please report the 'flashrom -p xxxx' output to flashrom(a)flashrom.org if it works for you. Please add the name of your PCI device to the subject. Thank you for your help! === PCI header type 0x00 Requested BAR is of type MEM, 32bit, not prefetchable PCI header type 0x00 Requested BAR is of type MEM, 32bit, not prefetchable page_size=1000 pre-rounding: start=0x00000000dfb70000, len=0x1000, end=0x00000000dfb71000 post-rounding: start=0x00000000dfb70000, len=0x1000, end=0x00000000dfb71000 Datasheet for this chipset can be found here: http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/ethe… Also I found: https://downloadcenter.intel.com/download/19186/Intel-Ethernet-Connections-… When run it: ./bootutil64e Intel(R) Ethernet Flash Firmware Utility BootUtil version 1.5.72.1 Copyright (C) 2003-2015 Intel Corporation Type BootUtil -? for help Port Network Address Location Series WOL Flash Firmware Version ==== =============== ======== ======= === ============================= ======= 1 002590E72B10 5:00.0 Gigabit YES FLASH Not Present 2 002590E72B11 5:00.1 Gigabit NO FLASH Not Present 3 002590E72B12 5:00.2 Gigabit NO FLASH Not Present 4 002590E72B13 5:00.3 Gigabit NO FLASH Not Present Any chance to have support for this card by flashroom ? Best Regards, Grzegorz Hetman.

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom