- flashrom - mail.coreboot.org

looking to flash a chromebook w/o developer mode
by Sean Felipe Wolfe 08 Dec '16

08 Dec '16

Hey everybody, I'm a developer sponsoring a local high school computer club. We've got chromebooks from the school system, and we are using crouton to install ubuntu side by side, thereby having a pretty robust little platform for light Python programming. HOWever, due to some school bureaucracy, many of the laptops are restricted from entering developer mode. This apparently is configured by the administrators who are several campuses removed, and attempts to have them relax the dependency on the club's laptops have not been successful. So far the security seems pretty robust -- we replaced SSDs and pulled the write-protect screw, then reinstalled chromeos, but after a clean install and enabling developer mode, the 'developer mode has been restricted' screen comes up and we reboot into normal chromeos. So ... I am looking for options. Based on my reading on the coreboot site, I believe it is technically possible to use an external programmer such as a Bus Pirate to reprogram the BIOS and overwrite the restriction area. I'd like to learn more about what's involved -- sounds plenty interesting. Thanks! -- A musician must make music, an artist must paint, a poet must write, if he is to be ultimately at peace with himself. - Abraham Maslow

1 0

(no subject)
by SandShark＠aol.com 05 Dec '16

05 Dec '16

I'm having a problem with flashrom V0.9.7. I was following instructions that used v0.9.3 to update the bios on a ReadyNAS Pro6, which apparently worked: # /opt/biosflash/flashrom -c W25x80 -w /opt/biosflash/RN_NV6_072610.ROM flashrom v0.9.3-r1205 on Linux 3.7.5-1.el6.elrepo.x86_64 (x86_64), built with libpci 2.2.4-pre4, GCC 4.1.2 20061115 (prerelease) (Debian 4.1.1-21), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "Intel ICH8/ICH8R", enabling flash write... OK. This chipset supports the following protocols: FWH,SPI. Found chip "Winbond W25x80" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash before programming... Erasing flash chip... SUCCESS. done. Programming flash... done. COMPLETE. Verifying flash... VERIFIED. But v0.9.7 requires configuration first, which fails, even though it finds both the chipset and the BIOS chip. This is also under a later Debian release, if that matters. The key to the problem seems to be "/dev/mem mmap failed: Resource temporarily unavailable". But I am logged in as root and /dev/mem has the proper permissions: crw-r----- 1 root kmem 1, 1 Nov 28 23:23 mem I have verified this response on two identical configurations, but I also have a different model ReadyNAS with the same Debian configuration and it works fine there. Here is the whole dump of the response: root@NASPro2:/data/Documents/BIOS# flashrom --programmer internal flashrom v0.9.7-r1782 on Linux 4.1.30.x86_64.1 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "Intel ICH8/ICH8R". Enabling flash write... BBAR offset is unknown on ICH8! OK. Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1080000 bytes at 0x00000000fef80000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x1000000 bytes at 0x00000000ff000000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Found Winbond flash chip "W25X80" (1024 kB, SPI) at physical address 0xfff00000. Error accessing flash chip, 0x800000 bytes at 0x00000000ff800000 /dev/mem mmap failed: Resource temporarily unavailable Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org Trying to unmap a nonexisting mapping! Please report a bug at flashrom(a)flashrom.org No operations were specified. root@NASPro2:/data/Documents/BIOS#

2 1

FAILED:ASUS H81M-C
by Rubén Bel Meseguer 05 Dec '16

05 Dec '16

Hello i have problems wich flashrom and motherboard asus h81m-c for write a bios: Found Winbond flash chip "W25Q64.V" (8192 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Enabling flash write... Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. Warning: SPI Configuration Lockdown activated. PROBLEMS, continuing anyway Your flash chip is in an unknown state. Afudos in windows dos say the bios is write protected. Please can help me to remove write protection on chip or motherboar asus h81m-c. Can install the patches of flashrom for more options? need a tutorial for install the patches please, i new. https://patchwork.coreboot.org/project/flashrom/list/?page=1 I paste the logs of flashrom for more information. Sorry my english. Greatings. t@t:~$ sudo flashrom -p internal --erase flashrom v0.9.9-r1955 on Linux 4.4.0-47-generic (x86_64) flashrom is free software, get the source code at https://flashrom.org Calibrating delay loop... OK. Found chipset "Intel H81". This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. Warning: SPI Configuration Lockdown activated. PROBLEMS, continuing anyway Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Erasing and writing flash chip... Transaction error! spi_block_erase_20 failed during command execution at address 0x180000 Reading current flash chip contents... done. Looking for another erase function. spi_block_erase_52 failed during command execution at address 0x180000 Reading current flash chip contents... done. Looking for another erase function. spi_block_erase_d8 failed during command execution at address 0x180000 Reading current flash chip contents... done. Looking for another erase function. spi_chip_erase_60 failed during command execution Reading current flash chip contents... done. Looking for another erase function. spi_chip_erase_c7 failed during command execution Looking for another erase function. No usable erase functions left. FAILED! Your flash chip is in an unknown state. Get help on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with the subject "FAILED: <your board name>"! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! t@t:~$ sudo flashrom -p internal --write '/home/t/Desktop/H81MC.CAP' flashrom v0.9.9-r1955 on Linux 4.4.0-47-generic (x86_64) flashrom is free software, get the source code at https://flashrom.org Calibrating delay loop... OK. Found chipset "Intel H81". This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. Warning: SPI Configuration Lockdown activated. PROBLEMS, continuing anyway Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Error: Image size (8390656 B) doesn't match the flash chip's size (8388608 B)! t@t:~$ sudo -i root@t:~# flashrom -p internal -V flashrom v0.9.9-r1955 on Linux 4.4.0-51-generic (x86_64) flashrom is free software, get the source code at https://flashrom.org flashrom was built with libpci 3.3.1, GCC 5.4.0 20160609, little endian Command line (3 args): flashrom -p internal -V Calibrating delay loop... OS timer resolution is 1 usecs, 3220M loops per second, 10 myus = 10 us, 100 myus = 117 us, 1000 myus = 997 us, 10000 myus = 9873 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Desktop" DMI string system-manufacturer: "ASUS" DMI string system-product-name: "All Series" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK COMPUTER INC." DMI string baseboard-product-name: "H81M-C" DMI string baseboard-version: "Rev X.0x" Found chipset "Intel H81" with PCI ID 8086:8c5c. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc65: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: enabled (A16(+) inverted) 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI Read Configuration: prefetching enabled, caching enabled, BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed. New value is 0x2a. SPIBAR = 0x00007f9c9de52000 + 0x3800 0x04: 0xf008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write. 0x58: 0x07ff0180 FREG1: BIOS region (0x00180000-0x007fffff) is read-write. 0x5C: 0x017f0001 FREG2: Management Engine region (0x00001000-0x0017ffff) is read-write. 0x90: 0xc4 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xfc4240 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=4, DBC=2, SME=0, SCF=4 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xD0: 0xffffffff (FPB) PROBLEMS, continuing anyway The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DL081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DL161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25F512, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512A, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25F1024(A), 128 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F2048, 256 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F4096, 512 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB321E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESMT F25L32PA, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESI ES25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESI ES25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESI ES25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q128C, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25VQ21B, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25VQ40C, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25VQ41B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25VQ80C, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25VQ16C, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX23L1654, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX23L3254, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX23L6454, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX23L12854, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L2005(C)/MX25L2006E, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L4005(A/C)/MX25L4006E, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L8005/MX25L8006E/MX25L8008E/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605A/MX25L1606E/MX25L1608E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3206E/MX25L3208E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3273E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6405D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6436E/MX25L6445E/MX25L6465E/MX25L6473E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L12805D, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L12835F/MX25L12845E/MX25L12865E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U12835F, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6495F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LQ020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LQ040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LQ080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LQ016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LQ032C, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV512(A), 64 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW106, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW406A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FU406B, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FU406C/LE25U40CMC, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW418A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW806, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW808, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL132K, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL164K, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL127S-64kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL127S-256kB, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL128P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL128P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL128S......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL128S......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL129P......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL129P......1, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25LF020A, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080(A), 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF512(A), 64 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF010(A), 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020, 256 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF020B, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25WF020A, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q40.V, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Chip status register is 0x00. Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x94, id2 0x8e, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x94, id2 0x8e, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x94, id2 0x8e, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x84, id2 0x58, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x94, id2 0x8e, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x94, id2 0x8e, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x5a, id2 0x8a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q64.V" (8192 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). No operations were specified. Restoring MMIO space at 0x7f9c9de558a0 Restoring PCI config space for 00:1f:0 reg 0xdc t@t:~$ sudo -i root@t:~# lspci -nnvvxxx 00:00.0 Host bridge [0600]: Intel Corporation 4th Gen Core Processor DRAM Controller [8086:0c00] (rev 06) Subsystem: ASUSTeK Computer Inc. 4th Gen Core Processor DRAM Controller [1043:8534] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: hsw_uncore 00: 86 80 00 0c 06 00 90 20 06 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 90 d1 fe 00 00 00 00 01 00 d1 fe 00 00 00 00 50: 11 02 00 00 19 00 00 00 17 00 10 df 01 00 00 da 60: 05 00 00 f8 00 00 00 00 01 80 d1 fe 00 00 00 00 70: 00 00 f0 ff 7f 00 00 00 00 04 00 00 00 00 00 00 80: 10 11 11 00 00 00 11 00 1a 00 00 00 00 00 00 00 90: 01 00 00 00 02 00 00 00 01 00 d0 20 02 00 00 00 a0: 01 00 00 00 02 00 00 00 01 00 e0 20 02 00 00 00 b0: 01 00 20 db 01 00 00 db 01 00 00 da 01 00 20 df c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 09 00 0c 01 61 e0 04 62 d0 00 54 44 00 00 00 00 f0: 00 00 00 00 c8 0f 03 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [8086:0c01] (rev 06) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 24 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: ASUSTeK Computer Inc. Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [1043:8534] Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4181 Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending+ InProgress- Capabilities: [140 v1] Root Complex Link Desc: PortNumber=02 ComponentID=01 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed19000 Kernel driver in use: pcieport Kernel modules: shpchp 00: 86 80 01 0c 07 04 10 00 06 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 88 00 00 00 00 00 00 00 0b 01 10 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 43 10 34 85 90: 05 a0 01 00 0c f0 e0 fe 81 41 00 00 00 00 00 00 a0: 10 00 42 01 00 80 00 00 00 00 00 00 02 cd 61 02 b0: 00 00 01 10 80 25 0c 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 80 0b 08 00 00 64 00 00 06 00 00 00 d0: 42 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 4e 01 01 42 00 00 00 00 00 00 10 00 00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller [8086:0412] (rev 06) (prog-if 00 [VGA controller]) DeviceName: Onboard IGD Subsystem: ASUSTeK Computer Inc. Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller [1043:8534] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 28 Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0800c Data: 4152 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a4] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: i915 Kernel modules: i915 00: 86 80 12 04 07 04 90 00 06 00 00 03 00 00 00 00 10: 04 00 80 f7 00 00 00 00 0c 00 00 e0 00 00 00 00 20: 01 f0 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 90 00 00 00 00 00 00 00 0b 01 00 00 40: 09 00 0c 01 61 e0 04 62 d0 00 54 44 00 00 00 00 50: 11 02 00 00 19 00 00 00 00 00 00 00 01 00 20 db 60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 05 d0 01 00 0c 80 e0 fe 52 41 00 00 00 00 00 00 a0: 00 00 00 00 13 00 06 03 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 a4 22 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 01 00 00 00 00 80 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 06 00 18 50 84 d8 00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 05) (prog-if 30 [XHCI]) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family USB xHCI [1043:8534] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 25 Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ Address: 00000000fee0400c Data: 41d1 Kernel driver in use: xhci_hcd 00: 86 80 31 8c 06 04 90 02 05 30 03 0c 00 00 00 00 10: 04 00 d0 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 70 00 00 00 00 00 00 00 0a 01 00 00 40: fd 01 36 80 89 c6 0f 80 00 00 00 00 00 00 00 00 50: 9f 6e 88 07 00 00 00 00 00 00 00 00 00 00 00 00 60: 30 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 80 c2 c1 08 00 00 00 00 00 00 00 00 00 00 00 80: 05 00 87 00 0c 40 e0 fe 00 00 00 00 d1 41 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 40 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 0f 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 03 0c 30 c0 03 0c 30 00 03 0c 30 00 00 00 00 00 d0: ff 0f 00 00 ff 0f 00 00 03 00 00 00 03 00 00 00 e0: f4 01 00 00 00 00 00 00 00 00 00 00 d8 d8 d8 08 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 [8086:8c2d] (rev 05) (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family USB EHCI [1043:8534] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at f7d18000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci-pci 00: 86 80 2d 8c 06 00 90 02 05 20 03 0c 00 00 00 00 10: 00 80 d1 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 50 00 00 00 00 00 00 00 0f 01 00 00 40: 00 00 00 00 db 05 eb 11 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 98 a0 20 00 00 00 00 60: 20 20 81 07 00 00 00 00 01 00 00 01 00 00 00 40 70: 00 00 ff 3f 03 0c 30 00 4f 01 00 00 8c 40 00 00 80: 00 00 80 00 11 88 0c 93 70 0d 00 24 01 04 02 00 90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 ef ff 27 00 00 00 e0: 00 00 00 00 ff ff ff ff ff ff ff ff 78 e2 ee df f0: 00 00 00 00 88 85 80 00 b1 0f 06 08 08 17 1a 20 00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 05) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset High Definition Audio Controller [1043:8576] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 29 Region 0: Memory at f7d10000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0e00c Data: 4172 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=2 ArbSelect=Fixed TC/VC=04 Status: NegoPending- InProgress- Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 00: 86 80 20 8c 06 04 10 00 05 00 03 04 10 00 00 00 10: 04 00 d1 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 76 85 30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00 40: 03 00 00 17 00 00 00 00 00 00 00 00 00 80 00 00 50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 70 81 00 0c e0 e0 fe 00 00 00 00 72 41 00 00 70: 10 00 91 00 00 00 00 10 00 00 10 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 04 02 01 00 60 00 00 00 0c 85 82 10 00 33 02 d0: 00 0c 85 02 10 00 33 02 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 [8086:8c10] (rev d5) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: df200000-df3fffff Prefetchable memory behind bridge: 00000000df400000-00000000df5fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train+ SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #0, PowerLimit 0.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Via WAKE# ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family PCI Express Root Port [1043:8534] Capabilities: [a0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport Kernel modules: shpchp 00: 86 80 10 8c 07 00 10 00 d5 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 20 20 00 20 20: 20 df 30 df 41 df 51 df 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 10 00 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 4c 31 01 50: 03 00 01 18 60 00 04 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 17 08 08 00 00 04 00 00 00 00 00 00 70: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 43 10 34 85 00 00 00 00 00 00 00 00 a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 01 00 08 00 00 02 00 11 09 00 00 00 00 e0: 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 f0: 50 00 00 00 80 f5 00 00 b1 0f 06 08 b0 03 04 01 00:1c.2 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 [8086:8c14] (rev d5) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f7c00000-f7cfffff Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family PCI Express Root Port [1043:8534] Capabilities: [a0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport Kernel modules: shpchp 00: 86 80 14 8c 07 00 10 00 d5 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 e0 e0 00 00 20: c0 f7 c0 f7 01 f0 01 f0 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 07 03 10 00 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 32 03 50: 42 00 11 70 00 b2 14 00 00 00 40 00 00 00 00 00 60: 00 00 00 00 17 08 00 00 00 04 00 00 00 00 00 00 70: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 43 10 34 85 00 00 00 00 00 00 00 00 a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 01 42 18 00 00 08 80 11 8b 00 00 00 00 e0: 00 00 00 00 00 00 3c 88 10 00 00 00 00 00 00 00 f0: 50 00 00 00 40 00 00 0c b1 0f 06 08 b0 03 00 03 00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 [8086:8c26] (rev 05) (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family USB EHCI [1043:8534] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f7d17000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci-pci 00: 86 80 26 8c 06 00 90 02 05 20 03 0c 00 00 00 00 10: 00 70 d1 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 01 00 00 40: 00 00 00 00 db 05 fb 11 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 98 a0 20 00 00 00 00 60: 20 20 01 06 00 00 00 00 01 00 00 01 00 00 00 40 70: 00 00 ff 3f 03 0c 30 c0 4f 01 00 00 8c 40 00 00 80: 00 00 80 00 11 88 0c 93 70 0d 00 24 01 04 02 00 90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 fb df 27 00 00 00 e0: 00 00 00 00 ff ff ff ff ff ff ff ff fc 46 a9 24 f0: 00 00 00 00 88 85 80 00 b1 0f 06 08 08 17 1a 20 00:1f.0 ISA bridge [0601]: Intel Corporation C220 Series Chipset Family H81 Express LPC Controller [8086:8c5c] (rev 05) Subsystem: ASUSTeK Computer Inc. C220 Series Chipset Family H81 Express LPC Controller [1043:8534] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00: 86 80 5c 8c 07 00 10 02 05 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 18 00 00 80 00 00 00 01 1c 00 00 10 00 00 00 50: f8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 8b 80 87 86 90 00 00 00 8f 8a 83 8e f8 f0 00 00 70: 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 80: 10 00 0f 3c 91 02 0c 00 01 0a 7c 00 00 00 00 00 90: 00 00 00 00 00 0f 00 00 00 00 00 00 00 00 00 00 a0: 10 06 80 18 09 18 06 00 00 46 00 00 00 00 01 00 b0: 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 33 22 11 00 67 45 00 00 cf ff 00 00 2a 00 00 00 e0: 09 00 0c 10 00 00 00 00 01 01 f1 91 00 00 00 00 f0: 01 c0 d1 fe 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 05) (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [1043:8534] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 26 Region 0: I/O ports at f0b0 [size=8] Region 1: I/O ports at f0a0 [size=4] Region 2: I/O ports at f090 [size=8] Region 3: I/O ports at f080 [size=4] Region 4: I/O ports at f060 [size=32] Region 5: Memory at f7d16000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0800c Data: 4122 Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 Kernel driver in use: ahci Kernel modules: ahci 00: 86 80 02 8c 07 04 b0 02 05 01 06 01 00 00 00 00 10: b1 f0 00 00 a1 f0 00 00 91 f0 00 00 81 f0 00 00 20: 61 f0 00 00 00 60 d1 f7 00 00 00 00 43 10 34 85 30: 00 00 00 00 80 00 00 00 00 00 00 00 06 02 00 00 40: 00 80 00 80 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 a8 03 40 08 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 01 00 0c 80 e0 fe 22 41 00 00 00 00 00 00 90: 60 3c 03 83 83 01 00 3c 20 02 5c e0 21 00 00 80 a0: a8 00 00 00 00 00 00 00 12 00 10 00 48 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 05) Subsystem: ASUSTeK Computer Inc. 8 Series/C220 Series Chipset Family SMBus Controller [1043:8534] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 7 Region 0: Memory at f7d15000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f040 [size=32] Kernel modules: i2c_i801 00: 86 80 22 8c 03 00 80 02 05 00 05 0c 00 00 00 00 10: 04 50 d1 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 41 f0 00 00 00 00 00 00 00 00 00 00 43 10 34 85 30: 00 00 00 00 00 00 00 00 00 00 00 00 07 03 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 0c) Subsystem: ASUSTeK Computer Inc. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [1043:8554] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 27 Region 0: I/O ports at e000 [size=256] Region 2: Memory at f7c00000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0200c Data: 4142 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via message/WAKE# DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Unknown small resource type 00, will not decode more. Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 71680ns Max no snoop latency: 71680ns Kernel driver in use: r8169 Kernel modules: r8169 00: ec 10 68 81 07 04 10 00 0c 00 00 02 10 00 00 00 10: 01 e0 00 00 00 00 00 00 04 00 c0 f7 00 00 00 00 20: 0c 00 00 f0 00 00 00 00 00 00 00 00 43 10 54 85 30: 00 00 00 00 40 00 00 00 00 00 00 00 07 01 00 00 40: 01 50 c3 ff 08 00 00 00 00 00 00 00 00 00 00 00 50: 05 70 81 00 0c 20 e0 fe 00 00 00 00 42 41 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 b0 02 02 c0 8c 90 05 00 50 10 00 11 7c 47 00 80: 42 01 11 10 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 1f 08 0c 00 00 04 00 00 02 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 11 d0 03 00 04 00 00 00 04 08 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 03 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 t@t:~$ sudo -i root@t:~# superiotool -deV superiotool r6637 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x0400, id=0x62c5 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0xc562, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0xc562 Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0xc562, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xc5/0x0f, rev=0x62 Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for VIA Super I/O at 0x3f0... PCI device 1106:0686 not found. Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff No Super I/O found

1 0

Re: [flashrom] Any chance of getting Flashrom 0.9.8 for DOS?
by Stefan Tauner 05 Dec '16

05 Dec '16

On Sun, 4 Dec 2016 23:45:25 +0000 Lu Xie <firexl(a)hotmail.com> wrote: > Thanks for the information. I will give it a try next time. The executable looks much larger than the 0.9.6.1 I have (728KB vs. 200-ish KB). I have been using flashrom with a bootable floppy disk most of the time so 700+KB seems a little too gigantic. Maybe it's time for me to dust off my old zip drives :) Hi, I have added two additional binaries based on the existing .exe. One is just stripped from symbols (I think this is what we offered earlier, but it is still rather big), and the second one is additionally compressed with upx and ends up being only 199296 bytes. HTH -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] Any chance of getting Flashrom 0.9.8 for DOS?
by Stefan Tauner 05 Dec '16

05 Dec '16

On Sun, 4 Dec 2016 20:59:12 +0000 Lu Xie <firexl(a)hotmail.com> wrote: > Hi, > > I have been quite happy with the 0.9.6.1 release for DOS and I decided to get a newer version. I tried several compiled executables from the buildbot repository but they are all unstable. I did a search in the wayback machine and found that 0.9.8 was the last stable release that had a DOS executable stored outside the buildbot repository, but the link (http://ra.openbios.org/~idwer/flashrom/dos/) seems to be dead. I googled for hours but couldn't find a copy of a 0.9.8 DOS executable. Could you please send me a copy of it from your archive or repository? Thanks. > > Lu Hello Lu, we may host pre-built binaries for less open-oriented systems in the future again and will change the respective links on our website. For now you can use the files located here http://buildbot.flashrom.org/buildresults/flashrom-000577-MQE/dos/ They use the source code of 0.9.9. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] Any chance of getting Flashrom 0.9.8 for DOS?
by Idwer Vollering 04 Dec '16

04 Dec '16

Why is DOS a must-have in your use case? Yes, I did cross-compile for DOS, however that was a while ago. I don't support DOS (anymore). - idwer 2016-12-04 21:59 GMT+01:00 Lu Xie <firexl(a)hotmail.com>: > Hi, > > I have been quite happy with the 0.9.6.1 release for DOS and I decided to > get a newer version. I tried several compiled executables from the buildbot > repository but they are all unstable. I did a search in the wayback machine > and found that 0.9.8 was the last stable release that had a DOS executable > stored outside the buildbot repository, but the link > (http://ra.openbios.org/~idwer/flashrom/dos/) seems to be dead. I googled > for hours but couldn't find a copy of a 0.9.8 DOS executable. Could you > please send me a copy of it from your archive or repository? Thanks. > > Lu > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > https://www.flashrom.org/mailman/listinfo/flashrom

1 0

Any chance of getting Flashrom 0.9.8 for DOS?
by Lu Xie 04 Dec '16

04 Dec '16

Hi, I have been quite happy with the 0.9.6.1 release for DOS and I decided to get a newer version. I tried several compiled executables from the buildbot repository but they are all unstable. I did a search in the wayback machine and found that 0.9.8 was the last stable release that had a DOS executable stored outside the buildbot repository, but the link (http://ra.openbios.org/~idwer/flashrom/dos/) seems to be dead. I googled for hours but couldn't find a copy of a 0.9.8 DOS executable. Could you please send me a copy of it from your archive or repository? Thanks. Lu

1 0

[PATCH] internal: Dont define functions on yet unsupported architechtures
by Urja Rannikko 04 Dec '16

04 Dec '16

This fixes a warning with newer (6.1) gcc on ARM, as tested by swiftgeek on irc. Signed-off-by: Urja Rannikko <urjaman(a)gmail.com> --- internal.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/internal.c b/internal.c index 4062b64..aa5f1d1 100644 --- a/internal.c +++ b/internal.c @@ -131,6 +131,8 @@ int register_superio(struct superio s) int is_laptop = 0; int laptop_ok = 0; +/* This matches with the #if for the registration of par_master_internal */ +#if IS_X86 || IS_MIPS static void internal_chip_writeb(const struct flashctx *flash, uint8_t val, chipaddr addr); static void internal_chip_writew(const struct flashctx *flash, uint16_t val, @@ -155,6 +157,7 @@ static const struct par_master par_master_internal = { .chip_writel = internal_chip_writel, .chip_writen = fallback_chip_writen, }; +#endif enum chipbustype internal_buses_supported = BUS_NONE; @@ -358,6 +361,8 @@ int internal_init(void) } #endif +/* This matches with the #if for the registration of par_master_internal */ +#if IS_X86 || IS_MIPS static void internal_chip_writeb(const struct flashctx *flash, uint8_t val, chipaddr addr) { @@ -400,3 +405,4 @@ static void internal_chip_readn(const struct flashctx *flash, uint8_t *buf, mmio_readn((void *)addr, buf, len); return; } +#endif -- 2.9.3

2 1

Re: [flashrom] [patch] serprog hangs under FreeBSD
by Stefan Tauner 04 Dec '16

04 Dec '16

On Fri, 2 Dec 2016 18:41:26 +0300 Michael Zhilin <mizhka(a)gmail.com> wrote: > Hi, > > This is attached patch to avoid hang of serprog under FreeBSD. Patch is > against trunk (r1955, 10 context lines). > > My use case is flashrom+serprog to read SPI flash (MX25L6406) via Arduino > Nano V3. Actual command is: > /usr/local/bin/flashrom -p serprog:dev=/dev/cuaU0:57600 -c > MX25L6406E/MX25L6408E -r tcw770.dump > > Using flashrom 0.9.9 it hangs after 5 seconds on read from tty ("ttyin"). > The problem is that kernel method "ttydisc_rint" ignore same bytes. It > happens due to enabled IEXTEN local flag of termios. TTY cuts few bytes, > Arduino reads 11264 bytes, but flashrom gets 11244 bytes (corrupted) and > waits for remaining 20 bytes. > > The fix is simple: turn off IEXTEN local flag. > > Tested on Arduino Nano V3 + FreeBSD 12-CURRENT. But I didn't check > compilation on other BSD / Linux distros. Could you please test it and let > me know results? > > Signed-off-by: Michael Zhilin <mizhka(a)gmail.com> > I've added signed-off-by here, because I don't know how to add it into svn > patch. > It's my first patch, so please let me know if i miss anything. Thank you Michael! I have verified that it builds fine: http://buildbot.flashrom.org/buildresults/flashrom-000559-9j8/results.html I will merge it as soon as we finished migrating to git (and gerrit+jenkins). -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] In-System Programming
by Arian Sanusi 03 Dec '16

03 Dec '16

Hi Lorentz > Now what I am wondering if I can do In-System Programming by powering up the mainboard and only use the data pins of the spi header. Problem is I don't know if this is possible, because CS# and DO are also on high level! And what do I do with the clk signal? Is it povided by the mainboard and messes up with the signal of the programmer? Or is it possible that the chip is electrically damaged, although I can read out its ID? Soldering it out is what I want to do last! Check whether CS#, DO are connected by pull-ups with an ohmmeter when the system is shut down. I think I saw a board where CS# was wired that way. That way you can actively drive down CS# and be fine. However, I'd at least check whether there's bus activity before doing anything... cheers, Arian

1 0

[patch] serprog hangs under FreeBSD
by Michael Zhilin 02 Dec '16

02 Dec '16

Hi, This is attached patch to avoid hang of serprog under FreeBSD. Patch is against trunk (r1955, 10 context lines). My use case is flashrom+serprog to read SPI flash (MX25L6406) via Arduino Nano V3. Actual command is: /usr/local/bin/flashrom -p serprog:dev=/dev/cuaU0:57600 -c MX25L6406E/MX25L6408E -r tcw770.dump Using flashrom 0.9.9 it hangs after 5 seconds on read from tty ("ttyin"). The problem is that kernel method "ttydisc_rint" ignore same bytes. It happens due to enabled IEXTEN local flag of termios. TTY cuts few bytes, Arduino reads 11264 bytes, but flashrom gets 11244 bytes (corrupted) and waits for remaining 20 bytes. The fix is simple: turn off IEXTEN local flag. Tested on Arduino Nano V3 + FreeBSD 12-CURRENT. But I didn't check compilation on other BSD / Linux distros. Could you please test it and let me know results? Signed-off-by: Michael Zhilin <mizhka(a)gmail.com> I've added signed-off-by here, because I don't know how to add it into svn patch. It's my first patch, so please let me know if i miss anything. Thanks, Michael!

1 0

In-System Programming
by Lorenz Litzenberger 02 Dec '16

02 Dec '16

1 0

Re: [flashrom] How to only flash BIOS region on braswell.
by Nico Huber 23 Nov '16

23 Nov '16

On 23.11.2016 08:46, Sampson Lee wrote: > Hi Nico, > > The BIOS bin and log in attachment. the `--layout` parameter needs a special file that only specifies the layout. You'd still give your flash image to the `-w` parameter. Please read the section about the `--layout` parameter in the flashrom manual page (e.g. [1]). As you are working with coreboot, you can generate the layout file from the flash image with ifdtool's `-f` parameter (it's in util/ifdtool/ in the coreboot source tree). Hope that helps, Nico [1] https://linux.die.net/man/8/flashrom > > Thanks. > Sampson. > > 2016-11-23 3:20 GMT+08:00 Nico Huber <nico.h(a)gmx.de>: > >> Hi Sampson, >> >> On 21.11.2016 04:33, Sampson Lee wrote: >>> I add a few point: >>> >>> I use flshrom version:0.99. >>> I try command "--layout" to read my rom file,but it show error message >>> "error parsing layout file". >> >> well, it means what it says, flashrom can't understand the file you gave >> to the `--layout` parameter. >> >> Please send us your layout file and a full log of the failing command >> (e.g. by adding `-o logfile.txt` to the flashrom command line). >> >> Regards, >> Nico >> >> >

1 0

[PATCH] Convert flashrom to git
by Stefan Tauner 23 Nov '16

23 Nov '16

- Drop support for Subversion in the getrevision script and Makefile. - Add .gitignore file - Restore modification dates of the exported files from the SCM. - Stop exporting SCM log dumps to CHANGELOG. This makes no sense. - Do not export the pre-"compiled" manpage. It can be generated like anything else from the code dump when we export the respective variable. The latter is added with this change. - Add some initial client-side git hooks * When committing check for obvious stuff you never want anyway: - white space errors - duplicate sign-offs * When pushing to the upstream repository check mandatory rules: - existing signoffs and acks in all new commits - no deletions or creation of branches - do not rewrite history of the precious branches, even if forced - Change version string of flashrom as follows. Previously, we included the last stable version according to a hard- coded string in the Makefile and appended the subversion revision number. With this patch the version string includes the last reachable git tag, number of commits since said tag in the upstream branches (if any), the name of said upstream branch, number of commits since that branch (if any), and the shortened git hash. In case there are uncommitted changes a "-dirty" indicator is also added. The case of unknown versions is explicitly handled in getrevision instead of simply appending "-unknown" to a hardcoded release number. The version information is either taken from an existing git remote pointing to an upstream repository (or a known mirror), or if that is not available - with the user's consent - a shadow copy is fetched from the upstream repo that is updated on every build (usually takes less than a second). In the following some examples of the version string changes are shown. Basically we print the distance to the last known upstream tag, which comprises any upstream commits since that tag as well as local commits on top of that. Additionally we handle upstream's stable and staging branches specially. Old output: flashrom v0.9.7-r1716 on Linux 3.8.0-6-generic (x86_64) New output variants: Build of the 0.9.99 release without any changes: flashrom 0.9.99-e4f6643 on Linux 3.13.0-76-generic (x86_64) 5 commits since last tag in upstream's stable branch: flashrom 0.9.99-5-stable-e4f6643-dirty on Linux 3.13.0-76-generic (x86_64) 3 commits since last tag in upstream's staging branch and 4 local commits on top of that: flashrom 0.9.99-3-staging-4-e4f6643 on Linux 3.13.0-76-generic (x86_64) 3 commits since last tag in upstream's staging branch and 4 local commits on top of that, and some local uncommitted changes too: flashrom 0.9.99-3-staging-4-e4f6643-dirty on Linux 3.13.0-76-generic (x86_64) 3 commits since the last tag in an unrelated upstream branch (e.g., a stable release *branch* such as 0.9.99) or local branch: flashrom 0.9.99-3-e4f6643 on Linux 3.13.0-76-generic (x86_64) No tags reachable from current commit (generic git fallback): flashrom d95935a version on Linux 3.13.0-76-generic (x86_64) Not in a repository: flashrom unknown version on Linux 3.13.0-76-generic (x86_64) Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- .gitignore | 14 +++ Makefile | 45 +++++--- flashrom.c | 2 +- util/getrevision.sh | 257 +++++++++++++++++++++++++++--------------- util/git-hooks/applypatch-msg | 15 +++ util/git-hooks/commit-msg | 15 +++ util/git-hooks/install.sh | 17 +++ util/git-hooks/pre-applypatch | 12 ++ util/git-hooks/pre-commit | 9 ++ util/git-hooks/pre-push | 74 ++++++++++++ util/git-hooks/wrapper.sh | 10 ++ 11 files changed, 360 insertions(+), 110 deletions(-) create mode 100644 .gitignore create mode 100755 util/git-hooks/applypatch-msg create mode 100755 util/git-hooks/commit-msg create mode 100755 util/git-hooks/install.sh create mode 100755 util/git-hooks/pre-applypatch create mode 100755 util/git-hooks/pre-commit create mode 100755 util/git-hooks/pre-push create mode 100755 util/git-hooks/wrapper.sh This is my current state of the infrastructure "needed" for flashrom to convert to git. Most of it is concerned with the version string generation and I had to jump through a number of hoops to get this far. The exact version strings are not final (e.g., tags and thus the first part of the string will get a 'v' prepended). We also need to find a proper way to integrate this into Gerrit... but it's a start *ahem* ;) You can test this code and the respective repo by cloning from here: https://flashrom.org/git/flashrom.git However, this is not final and *will* change before we finalize the migration. Currently the genuine source of flashrom's source is still the subversion repo! diff --git a/.gitignore b/.gitignore new file mode 100644 index 0000000..c478a67 --- /dev/null +++ b/.gitignore @@ -0,0 +1,14 @@ +*.d +*.o +/.features +/.dependencies +/.libdeps +/build_details.txt +/flashrom +/flashrom.exe +/flashrom.8 + +/util/ich_descriptors_tool/ich_descriptors_tool +/util/ich_descriptors_tool/ich_descriptors_tool.exe +/util/ich_descriptors_tool/.dep +/util/ich_descriptors_tool/.obj diff --git a/Makefile b/Makefile index 4ebde1e..c880764 100644 --- a/Makefile +++ b/Makefile @@ -526,18 +526,20 @@ LIB_OBJS = layout.o flashrom.o udelay.o programmer.o helpers.o CLI_OBJS = cli_classic.o cli_output.o cli_common.o print.o -# Set the flashrom version string from the highest revision number of the checked out flashrom files. +# Set the flashrom version string from the repository metadata (cf. util/getrevision.sh). # Note to packagers: Any tree exported with "make export" or "make tarball" -# will not require subversion. The downloadable snapshots are already exported. -SVNVERSION := $(shell ./util/getrevision.sh -u 2>/dev/null ) - -RELEASE := 0.9.9 -VERSION := $(RELEASE)-$(SVNVERSION) -RELEASENAME ?= $(VERSION) +# will not require git. The downloadable snapshots are already exported. +VERSION := $(shell ./util/getrevision.sh --revision) +# VERSION equals "offline" if online access is required but the respective git config variable is not set yet. +ifeq ($(VERSION),offline) + $(error Aborting.) +endif +SCMDEF := -D'FLASHROM_VERSION="$(VERSION)"' -SVNDEF := -D'FLASHROM_VERSION="$(VERSION)"' +# No spaces in release names unless set explicitly +RELEASENAME ?= $(shell echo "$(VERSION)" | sed -e 's/ /_/') -# Inform user if there is no meaningful version string. If there is version information from a VCS print +# Inform user about the version string used. If there is no version information from a VCS then print # something anyway because $(info...) will print a line break in any case which would look suspicious. # The && between the echos is a workaround for old versions of GNU make that issue the error "unterminated # variable reference" if a semicolon is used instead. @@ -1024,7 +1026,7 @@ libflashrom.a: $(LIBFLASHROM_OBJS) TAROPTIONS = $(shell LC_ALL=C tar --version|grep -q GNU && echo "--owner=root --group=root") %.o: %.c .features - $(CC) -MMD $(CFLAGS) $(CPPFLAGS) $(FLASHROM_CFLAGS) $(FEATURE_CFLAGS) $(SVNDEF) -o $@ -c $< + $(CC) -MMD $(CFLAGS) $(CPPFLAGS) $(FLASHROM_CFLAGS) $(FEATURE_CFLAGS) $(SCMDEF) -o $@ -c $< # Make sure to add all names of generated binaries here. # This includes all frontends and libflashrom. @@ -1344,12 +1346,16 @@ endif @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) + +$(shell ./util/git-hooks/install.sh) # Automatically install if need be + $(PROGRAM).8.html: $(PROGRAM).8 @groff -mandoc -Thtml $< >$@ +MAN_DATE := $(shell ./util/getrevision.sh -d $(PROGRAM).8.tmpl 2>/dev/null) $(PROGRAM).8: $(PROGRAM).8.tmpl @# Add the man page change date and version to the man page - @sed -e 's#.TH FLASHROM 8 ".*".*#.TH FLASHROM 8 "$(shell ./util/getrevision.sh -d $(PROGRAM).8.tmpl 2>/dev/null)" "$(VERSION)"#' <$< >$@ + @sed -e 's#.TH FLASHROM 8 .*#.TH FLASHROM 8 "$(MAN_DATE)" "$(VERSION)" "$(MAN_DATE)"#' <$< >$@ install: $(PROGRAM)$(EXEC_SUFFIX) $(PROGRAM).8 mkdir -p $(DESTDIR)$(PREFIX)/sbin @@ -1358,12 +1364,17 @@ install: $(PROGRAM)$(EXEC_SUFFIX) $(PROGRAM).8 $(INSTALL) -m 0644 $(PROGRAM).8 $(DESTDIR)$(MANDIR)/man8 export: $(PROGRAM).8 - @rm -rf $(EXPORTDIR)/flashrom-$(RELEASENAME) - @svn export -r BASE . $(EXPORTDIR)/flashrom-$(RELEASENAME) - @sed "s/^SVNVERSION.*/SVNVERSION := $(SVNVERSION)/" Makefile >$(EXPORTDIR)/flashrom-$(RELEASENAME)/Makefile - @cp $(PROGRAM).8 "$(EXPORTDIR)/flashrom-$(RELEASENAME)/$(PROGRAM).8" - @svn log >$(EXPORTDIR)/flashrom-$(RELEASENAME)/ChangeLog - @echo Exported $(EXPORTDIR)/flashrom-$(RELEASENAME)/ + @rm -rf "$(EXPORTDIR)/flashrom-$(RELEASENAME)" + @mkdir -p "$(EXPORTDIR)/flashrom-$(RELEASENAME)" + @git archive HEAD | tar -x -C "$(EXPORTDIR)/flashrom-$(RELEASENAME)" + @sed -e 's/^VERSION :=.*/VERSION := $(VERSION)/' \ + -e 's/^MAN_DATE :=.*/MAN_DATE := $(MAN_DATE)/' \ + -e 's#./util/getrevision.sh -c#false#' \ + Makefile >"$(EXPORTDIR)/flashrom-$(RELEASENAME)/Makefile" + @for f in `git ls-tree -r -t --full-name --name-only HEAD` ; do \ + touch -d `git log --pretty=format:%cI -1 HEAD -- "$$f"` "$(EXPORTDIR)/flashrom-$(RELEASENAME)/$$f"; \ + done + @echo "Exported $(EXPORTDIR)/flashrom-$(RELEASENAME)/" tarball: export @tar cjf $(EXPORTDIR)/flashrom-$(RELEASENAME).tar.bz2 -C $(EXPORTDIR)/ $(TAROPTIONS) flashrom-$(RELEASENAME)/ diff --git a/flashrom.c b/flashrom.c index 25e53f2..1a43303 100644 --- a/flashrom.c +++ b/flashrom.c @@ -1801,7 +1801,7 @@ void print_buildinfo(void) void print_version(void) { - msg_ginfo("flashrom v%s", flashrom_version); + msg_ginfo("flashrom %s", flashrom_version); print_sysinfo(); msg_ginfo("\n"); } diff --git a/util/getrevision.sh b/util/getrevision.sh index 1012058..1240e95 100755 --- a/util/getrevision.sh +++ b/util/getrevision.sh @@ -5,7 +5,7 @@ # Copyright (C) 2005 coresystems GmbH <stepan(a)coresystems.de> # Copyright (C) 2009,2010 Carl-Daniel Hailfinger # Copyright (C) 2010 Chromium OS Authors -# Copyright (C) 2013 Stefan Tauner +# Copyright (C) 2013-2016 Stefan Tauner # # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by @@ -30,31 +30,73 @@ export LC_ALL=C # nor local times or dates export TZ=UTC0 -# Helper functions -# First argument is the path to inspect (usually optional; w/o it the whole repository will be considered) -svn_has_local_changes() { - svn status "$1" | egrep '^ *[ADMR] *' >/dev/null +# List of important upstream branches... +upstream_branches="stable staging" +upstream_url="https://flashrom.org/git/flashrom.git" +upstream_patterns="github\.com.flashrom/flashrom\.git|flashrom\.org.git/flashrom\.git" + +upcache_prefix="refs/flashrom_org/" +# Generate upcache_refs +for b in $upstream_branches ; do + upcache_refs="$upcache_refs ${upcache_prefix}$b" +done + +# We need to update our upstream information sometimes so that we can create detailed version information. +# To that end the code below fetches parts of the upstream repository via https. +# This takes about one second or less under normal circumstances. +# +# It can be called manually, but is usually called via +# - the Makefile (implicitly via revision()) when there is no upstream information in any existing remote +forced_update() { + local rev_remote_refs + for ref in $upcache_refs ; do + rev_remote_refs="$rev_remote_refs +${ref##*/}:$ref" + done + git fetch -q "$upstream_url" --tags $rev_remote_refs && echo "Success." } +update() { + offline=$(git config flashrom.offline-builds 2>/dev/null) + if [ -z "$offline" ]; then + echo "To produce useful version information the build process needs access to the commit +history from an upstream repository. If no git remote is pointing to one we +can store the necessary information out of sight and update it on every build. +To enable this functionality and fetch the upstream commits from $upstream_url +please execute 'git config flashrom.offline-builds false' or add one of the +upstream repositories as git remote to rely on that information. +However, if you want to work completely offline and generate meaningless version +strings then disable it with 'git config flashrom.offline-builds true' +You can force updating the local commit cache with '$0 --forced-update'">&2 + return 1 + elif [ "x$offline" = "xfalse" ]; then + echo "Fetching commit history from upstream repository $upstream_url +To disable any network activity execute 'git config flashrom.offline-builds true'.">&2 + forced_update >/dev/null + else + echo "Fetching commit history from upstream is disabled - version strings might be misleading. +To ensure proper version strings and allow network access run 'git config flashrom.offline-builds false'.">&2 + fi + return 0 +} + +# Helper functions +# First argument is the path to inspect (usually optional; w/o it the whole repository will be considered) git_has_local_changes() { git update-index -q --refresh >/dev/null ! git diff-index --quiet HEAD -- "$1" } git_last_commit() { + # git rev-parse --short HEAD would suffice if repository as a whole is of interest (no $1) git log --pretty=format:"%h" -1 -- "$1" } -svn_is_file_tracked() { - svn info "$1" >/dev/null 2>&1 -} - git_is_file_tracked() { git ls-files --error-unmatch -- "$1" >/dev/null 2>&1 } is_file_tracked() { - svn_is_file_tracked "$1" || git_is_file_tracked "$1" + git_is_file_tracked "$1" } # Tries to find a remote source for the changes committed locally. @@ -89,13 +131,7 @@ git_url() { scm_url() { local url= - # for a primitive VCS like subversion finding the URL is easy: there is only one upstream host - if svn_is_file_tracked "$1" ; then - url="$(svn info "$1" 2>/dev/null | - grep URL: | - sed 's/.*URL:[[:blank:]]*//;s/:\/\/.*@/:\/\//' | - grep ^.)" - elif git_is_file_tracked "$1" ; then + if git_is_file_tracked "$1" ; then url="$(git_url "$1")" else return ${EXIT_FAILURE} @@ -116,29 +152,7 @@ timestamp() { # freebsd date [-jnu] [-d dst] [-r seconds] [-f fmt date | [[[[[cc]yy]mm]dd]HH]MM[.ss]] [+format] [...] # dragonflybsd date [-jnu] [-d dst] [-r seconds] [-f fmt date | [[[[[cc]yy]mm]dd]HH]MM[.ss]] [+format] [...] # openbsd date [-aju] [-d dst] [-r seconds] [+format] [[[[[[cc]yy]mm]dd]HH]MM[.SS]] [...] - if svn_is_file_tracked "$2" ; then - if svn_has_local_changes "$2"; then - t=$(date -u "$1") - else - # No local changes, get date of the last log record. Subversion provides that in - # ISO 8601 format when using the --xml switch. The sed call extracts that ignoring any - # fractional parts started by a comma or a dot. - local last_commit_date="$(svn info --xml "$2"| \ - sed -n -e 's/<date>$[^,\.]*$$[\.,].*$*Z<\/date>/\1Z/p')" - - case $(uname) in - # Most BSD dates do not support parsing date values from user input with -d but all of - # them support parsing the syntax with [[[[[[cc]yy]mm]dd]HH]MM[.ss]]. We have to - # transform the ISO8601 date first though. - NetBSD|OpenBSD|DragonFly|FreeBSD) - last_commit_date="$(echo ${last_commit_date} | \ - sed -n -e 's/$....$-$..$-$..$T$..$:$..$:$..$Z/\1\2\3\4\5\.\6/p')" - t=$(date -u -j "${last_commit_date}" "$1" 2>/dev/null);; - *) - t=$(date -u -d "${last_commit_date}" "$1" 2>/dev/null);; - esac - fi - elif git_is_file_tracked "$2" ; then + if git_is_file_tracked "$2" ; then # are there local changes? if git_has_local_changes "$2" ; then t=$(date -u "${1}") @@ -163,55 +177,102 @@ timestamp() { echo "${t}" } -# Retrieve local SCM revision info. This is useful if we're working in a different SCM than upstream and/or -# have local changes. -local_revision() { - local r= - - if svn_is_file_tracked "$1" ; then - r=$(svn_has_local_changes "$1" && echo "dirty") - elif git_is_file_tracked "$1" ; then - r=$(git_last_commit "$1") - - local svn_base=$(git log --grep=git-svn-id -1 --format='%h') - if [ "$svn_base" != "" ] ; then - local diff_to_svn=$(git rev-list --count ${svn_base}..${r}) - if [ "$diff_to_svn" -gt 0 ] ; then - r="$r-$diff_to_svn" - fi - fi +tag() { + local t= - if git_has_local_changes "$1" ; then - r="$r-dirty" + if git_is_file_tracked "$1" ; then + local sha=$(git_last_commit "$1") + t=$(git describe --abbrev=0 "$sha") + fi + if [ -z "$t" ]; then + t="unknown" # default to unknown + fi + echo "${t}" +} + +find_upremote() { + # Try to find upstream's remote name + for remote in $(git remote) ; do + local url=$(git ls-remote --get-url $remote) + if echo "$url" | grep -q -E "$upstream_patterns" ; then + echo "$remote" + return fi + done +} + +revision() { + local sha=$(git_last_commit "$1" 2>/dev/null) + # No git no fun + if [ -z "$sha" ]; then + echo "unknown" + return + fi + + local r="$sha" + if git_has_local_changes "$1" ; then + r="$r-dirty" + fi + + # sha + possibly dirty info is not exactly verbose, therefore the code below tries to use tags and + # branches from the upstream repos to derive a more previse version string. + # To that end we try to use the existing remotes first. + # If the upstream repos (and its mirrors) are not available as remotes, use a shadow copy instead. + + local up_refs + local up_remote=$(find_upremote) + if [ -n "$up_remote" ]; then + for b in $upstream_branches ; do + up_refs="$up_refs ${up_remote}/${b}" + done else - return ${EXIT_FAILURE} + update || { echo "offline" ; return ; } + up_refs=$upcache_refs fi - echo "${r}" -} + # Find nearest commit contained in this branch that is also in any of the up_refs, i.e. the branch point + # of the current branch. This might be the latest commit if it's in any of the upstream branches. + local merge_point=$(git merge-base ${sha} ${up_refs}) + local upstream_branch + if [ -z "$merge_point" ]; then + echo "$sha" + return + fi -# Get the upstream flashrom revision stored in SVN metadata. -upstream_revision() { - local r= - - if svn_is_file_tracked "$1" ; then - r=$(svn info "$1" 2>/dev/null | \ - grep "Last Changed Rev:" | \ - sed -e "s/^Last Changed Rev: *//" -e "s/$[0-9]*$.*/r\1/" | \ - grep "r[0-9]") - elif git_is_file_tracked "$1" ; then - # If this is a "native" git-svn clone we could use git svn log: - # git svn log --oneline -1 | sed 's/^r//;s/[[:blank:]].*//' or even git svn find-rev - # but it is easier to just grep for the git-svn-id unconditionally - r=$(git log --grep=git-svn-id -1 -- "$1" | \ - grep git-svn-id | \ - sed 's/.*@/r/;s/[[:blank:]].*//') + # If the current commit is reachable from any remote branch, append the branch name and its + # distance to the nearest earlier tag to that tag name itself (tag-distance-branch). + # If multiple branches are reachable then we use the newest one (by commit date). + # If none is reachable we use the nearest tag and ? for distances and remote branch name. + + local cnt_upstream_branch2sha=$(git rev-list --count "${merge_point}..${sha}" 2>/dev/null) + + local lasttag=$(git describe --abbrev=0 "$merge_point" 2>/dev/null) + if [ -z "$lasttag" ]; then + echo "Could not find tag reachable from merge point!">&2 + echo "$sha" + return fi - if [ -z "$r" ]; then - r="unknown" # default to unknown + local cnt_tag2upstream_branch + for ref in $up_refs ; do + if git merge-base --is-ancestor ${merge_point} ${ref}; then + upstream_branch=${ref##*/} # remove everything till last / + cnt_tag2upstream_branch=$(git rev-list --count "${lasttag}..${merge_point}" 2>/dev/null) + break + fi + done + + if [ "$cnt_upstream_branch2sha" -gt 0 ]; then + r="$cnt_upstream_branch2sha-$r" + fi + if [ "$cnt_tag2upstream_branch" -gt 0 ]; then + if [ -n "$upstream_branch" ]; then + r="$upstream_branch-$r" + fi + r="$cnt_tag2upstream_branch-$r" fi + r="$lasttag-$r" + echo "${r}" } @@ -228,16 +289,20 @@ Commands this message -c or --check test if path is under version control at all - -l or --local - local revision information including an indicator for uncommitted changes - -u or --upstream - upstream revision - -U or --url + -T or --tag + returns the name of the last release/tag + -r or --revision + return unique revision information including the last tag and an indicator for uncommitted changes + -u or --url URL associated with the latest commit -d or --date date of most recent modification -t or --timestamp timestamp of most recent modification + -U or --update + update local shadow copy of upstream commits if need be and offline builds are not enforced + --forced-update + force updating the local shadow copy of upstream commits " return } @@ -260,15 +325,15 @@ main() { -h|--help) action=show_help; shift;; - -l|--local) + -T|--tag) check_action $1 - action=local_revision + action=tag shift;; - -u|--upstream) + -r|--revision) check_action $1 - action=upstream_revision + action=revision shift;; - -U|--url) + -u|--url) check_action $1 action=scm_url shift;; @@ -280,9 +345,17 @@ main() { check_action $1 action="timestamp +%Y-%m-%dT%H:%M:%SZ" # There is only one valid time format! ISO 8601 shift;; + -U|--update) + check_action $1 + action=update + shift;; + --forced-update) + check_action $1 + action=forced_update + shift;; -c|--check) - check_action=$1 - action="is_tracked" + check_action $1 + action=is_tracked shift;; -*) show_help; diff --git a/util/git-hooks/applypatch-msg b/util/git-hooks/applypatch-msg new file mode 100755 index 0000000..32ff6c7 --- /dev/null +++ b/util/git-hooks/applypatch-msg @@ -0,0 +1,15 @@ +#!/bin/sh +# +# A hook script to check the commit log message taken by +# applypatch from an e-mail message (via git-am). +# We simply do the same as for other commit messages +# +# The hook should exit with non-zero status after issuing an +# appropriate message if it wants to stop the commit. The hook is +# allowed to edit the commit message file. +# + +. git-sh-setup +test -x "$GIT_DIR/hooks/commit-msg" && + exec "$GIT_DIR/hooks/commit-msg" ${1+"$@"} +: diff --git a/util/git-hooks/commit-msg b/util/git-hooks/commit-msg new file mode 100755 index 0000000..710fe78 --- /dev/null +++ b/util/git-hooks/commit-msg @@ -0,0 +1,15 @@ +#!/bin/sh +# +# A hook script to check the commit log message. +# Called by "git commit" with one argument, the name of the file +# that has the commit message. The hook should exit with non-zero +# status after issuing an appropriate message if it wants to stop the +# commit. The hook is allowed to edit the commit message file. +# + +# Catches duplicate Signed-off-by lines. +test "" = "$(grep '^Signed-off-by: ' "$1" | + sort | uniq -c | sed -e '/^[ ]*1[ ]/d')" || { + echo "Duplicate Signed-off-by lines." >&2 + exit 1 +} diff --git a/util/git-hooks/install.sh b/util/git-hooks/install.sh new file mode 100755 index 0000000..84151d0 --- /dev/null +++ b/util/git-hooks/install.sh @@ -0,0 +1,17 @@ +#!/bin/sh -e + +root=$(git rev-parse --show-cdup 2>/dev/null) || ( echo "Not under git control. Cannot install git hooks." >&2 ; exit 0 ) +dst="${root}"$(git rev-parse --git-path hooks/) +src=util/git-hooks/ # relative to root +hooks=$(cd "${root}${src}" && git ls-files -c | grep -Ev 'install.sh|wrapper.sh') + +for h in $hooks; do + # Test if hook is not already installed, i.e. doesn't point at the wrapper + if [ ! "${dst}$h" -ef "${root}${src}wrapper.sh" ]; then + # preserve custom hooks if any + if [ -e "${dst}$h" ]; then + mv "${dst}$h" "${dst}$h.local" + fi + ln -s "../../${src}wrapper.sh" "${dst}$h" + fi +done diff --git a/util/git-hooks/pre-applypatch b/util/git-hooks/pre-applypatch new file mode 100755 index 0000000..2ed28f7 --- /dev/null +++ b/util/git-hooks/pre-applypatch @@ -0,0 +1,12 @@ +#!/bin/sh +# +# An example hook script to verify what is about to be committed +# by applypatch from an e-mail message. +# +# The hook should exit with non-zero status after issuing an +# appropriate message if it wants to stop the commit. + +. git-sh-setup +test -x "$GIT_DIR/hooks/pre-commit" && + exec "$GIT_DIR/hooks/pre-commit" ${1+"$@"} +: diff --git a/util/git-hooks/pre-commit b/util/git-hooks/pre-commit new file mode 100755 index 0000000..dbccb9e --- /dev/null +++ b/util/git-hooks/pre-commit @@ -0,0 +1,9 @@ +#!/bin/sh +# +# A hook script to verify what is about to be committed. +# Called by "git commit" with no arguments. The hook should +# exit with non-zero status after issuing an appropriate message if +# it wants to stop the commit. + +# Check for whitespace errors +git diff-index --check --cached HEAD -- || exit 1 diff --git a/util/git-hooks/pre-push b/util/git-hooks/pre-push new file mode 100755 index 0000000..3fab8c4 --- /dev/null +++ b/util/git-hooks/pre-push @@ -0,0 +1,74 @@ +#!/bin/sh + +# A hook script to verify what is about to be pushed. Called by "git +# push" after it has checked the remote status, but before anything has been +# pushed. If this script exits with a non-zero status nothing will be pushed. +# +# This hook is called with the following parameters: +# +# $1 -- Name of the remote to which the push is being done +# $2 -- URL to which the push is being done +# +# If pushing without using a named remote those arguments will be equal. +# +# Information about the commits which are being pushed is supplied as lines to +# the standard input in the form: +# +# <local ref> <local sha1> <remote ref> <remote sha1> + +remote="$1" +url="$2" + +zero=0000000000000000000000000000000000000000 + +upstream_pattern="flashrom.org.*git/flashrom.git" +precious_branches=( stable staging ) + +# Only care about the upstream repository +if echo "$url" | grep -q -v -E "$upstream_pattern" ; then + exit 0 +fi + +while read local_ref local_sha remote_ref remote_sha ; do + if [ "$remote_ref" != "refs/heads/staging" -a "$remote_ref" != "refs/heads/stable" ]; then + echo "Feature branches not allowed ($remote_ref)." >&2 + exit 1 + fi + + if [ "$local_sha" = $zero ]; then + echo "Deletion of branches is prohibited." >&2 + exit 1 + else + if [ "$remote_sha" = "$zero" ]; then + echo "No new branches allowed." >&2 + exit 1 + else + range="$remote_sha..$local_sha" + fi + + # Check for Signed-off-by and Acked-by + commit=$(git rev-list -n 1 --all-match --invert-grep -E \ + --grep '^Signed-off-by: .+ <.+@.+\..+>$' --grep '^Acked-by: .+ <.+@.+\..+>$' "$range") + if [ -n "$commit" ]; then + echo "No Signoff or Ack found in commit $local_sha in $local_ref, not pushing." >&2 + exit 1 + fi + + # Make _really_ sure we do not rewrite precious history + for lbranch in "${precious_branches[@]}"; do + if [ "$remote_ref" = "refs/heads/$lbranch" ]; then + nonreachable=$(git rev-list $remote_sha ^$local_sha) + if [ -n "$nonreachable" ]; then + echo "Only fast-forward pushes are allowed on $lbranch." >&2 + echo "$nonreachable is not included in $remote_sha while pusing to $remote_ref" >&2 + exit 1 + fi + fi + done + + # FIXME: check commit log format (subject without full stop at the end etc). + # FIXME: do buildbot checks if authorized? + fi +done + +exit 0 diff --git a/util/git-hooks/wrapper.sh b/util/git-hooks/wrapper.sh new file mode 100755 index 0000000..3fc3e05 --- /dev/null +++ b/util/git-hooks/wrapper.sh @@ -0,0 +1,10 @@ +#!/bin/sh + +if [ -x $0.local ]; then + $0.local "$@" || exit $? +fi + +hook=$(git rev-parse --show-toplevel)"/util/git-hooks/"$(basename $0) +if [ -x $hook ]; then + $hook "$@" || exit $? +fi -- Kind regards, Stefan Tauner

2 2

Re: [flashrom] How to only flash BIOS region on braswell.
by Nico Huber 22 Nov '16

22 Nov '16

Hi Sampson, On 21.11.2016 04:33, Sampson Lee wrote: > I add a few point: > > I use flshrom version:0.99. > I try command "--layout" to read my rom file,but it show error message > "error parsing layout file". well, it means what it says, flashrom can't understand the file you gave to the `--layout` parameter. Please send us your layout file and a full log of the failing command (e.g. by adding `-o logfile.txt` to the flashrom command line). Regards, Nico

1 0

Re: [flashrom] How to only flash BIOS region on braswell.
by Sampson Lee 21 Nov '16

21 Nov '16

I add a few point: I use flshrom version:0.99. I try command "--layout" to read my rom file,but it show error message "error parsing layout file". So I can not use command "--image". Anybody have any idea?

1 0

How to only flash BIOS region on braswell.
by Sampson Lee 19 Nov '16

19 Nov '16

Hello, I have a question about flash BIOS region on braswell. I use W25Q64.V(8M),the layout is TXE(3M/address:0~0x300000)+BIOS(coreboot 2M/address:0x600000~0x800000). If I use command "flashrom -p internal -w xxx.bin",it will flash all data(8M). But I want to only flash BIOS region. Should i use which command to flash? Thanks. Sampson.

1 0

Re: [flashrom] [PATCH] RFC: enable flashrom to write images of arbitrary size
by Peter Mamonov 09 Nov '16

09 Nov '16

Hi David, On Tue, Nov 08, 2016 at 11:22:56AM -0800, David Hendricks wrote: > Hi Peter, > Thanks for the patch! However, I suspect this will not be accepted > since the size check is an important safety measure for the general > use case. > > In general layout files should be used for this sort of thing. The way > we've gone about this in the chromium.org branch is to augment the -i > syntax to allow the user to specify a region and corresponding file, > and we also added a "--fast-verify" mode to only verify regions which > were targeted. So for example you could do "flashrom -p <programmer> > -l <layout_file> -i region:filename.bin --fast-verify --ignore-fmap > -w" which will write filename.bin to the targeted region and verify > only that region. > > Details here: https://www.chromium.org/chromium-os/packages/cros-flashrom#TOC-Partial-Rea… > . LMK if this is any help. Thanks for the tip! Looks like an ultimate solution. I'll try it and report the results later. Regards, Peter > > > > On Mon, Nov 7, 2016 at 1:00 PM, Peter Mamonov <pmamonov(a)gmail.com> wrote: > > Flashrom restricts an image size to be equal to a ROM capacity. This is > > inconvenient in case of large and slow ROM chips, when only part of the ROM > > should be updated. This patch removes this restriction in a quick-and-dirty > > manner. > > > > Signed-off-by: Peter Mamonov <pmamonov(a)gmail.com> > > --- > > flashrom.c | 26 +++++++++++++++----------- > > 1 file changed, 15 insertions(+), 11 deletions(-) > > > > diff --git a/flashrom.c b/flashrom.c > > index d51a44c..f805e00 100644 > > --- a/flashrom.c > > +++ b/flashrom.c > > @@ -1255,30 +1255,30 @@ int read_buf_from_file(unsigned char *buf, unsigned long size, > > > > if ((image = fopen(filename, "rb")) == NULL) { > > msg_gerr("Error: opening file \"%s\" failed: %s\n", filename, strerror(errno)); > > - return 1; > > + return -1; > > } > > if (fstat(fileno(image), &image_stat) != 0) { > > msg_gerr("Error: getting metadata of file \"%s\" failed: %s\n", filename, strerror(errno)); > > fclose(image); > > - return 1; > > + return -1; > > } > > - if (image_stat.st_size != size) { > > + if (image_stat.st_size > size) { > > msg_gerr("Error: Image size (%jd B) doesn't match the flash chip's size (%lu B)!\n", > > (intmax_t)image_stat.st_size, size); > > - fclose(image); > > - return 1; > > + return -1; > > } > > + size = image_stat.st_size; > > numbytes = fread(buf, 1, size, image); > > if (fclose(image)) { > > msg_gerr("Error: closing file \"%s\" failed: %s\n", filename, strerror(errno)); > > - return 1; > > + return -1; > > } > > if (numbytes != size) { > > msg_gerr("Error: Failed to read complete file. Got %ld bytes, " > > "wanted %ld!\n", numbytes, size); > > - return 1; > > + return -1; > > } > > - return 0; > > + return size; > > #endif > > } > > > > @@ -1481,7 +1481,10 @@ static int walk_eraseregions(struct flashctx *flash, int erasefunction, > > * members so the loop below won't be executed for them. > > */ > > len = eraser.eraseblocks[i].size; > > - for (j = 0; j < eraser.eraseblocks[i].count; j++) { > > + for (j = 0; > > + j < eraser.eraseblocks[i].count && > > + start + len <= flash->chip->total_size * 1024; > > + j++) { > > /* Print this for every block except the first one. */ > > if (i || j) > > msg_cdbg(", "); > > @@ -1988,11 +1991,12 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it, > > } > > > > if (write_it || verify_it) { > > - if (read_buf_from_file(newcontents, size, filename)) { > > + size = read_buf_from_file(newcontents, size, filename); > > + if (size < 0) { > > ret = 1; > > goto out; > > } > > - > > + flash->chip->total_size = size / 1024; /* FIXME */ > > #if CONFIG_INTERNAL == 1 > > if (programmer == PROGRAMMER_INTERNAL && cb_check_image(newcontents, size) < 0) { > > if (force_boardmismatch) { > > -- > > 2.1.4 > > > > > > _______________________________________________ > > flashrom mailing list > > flashrom(a)flashrom.org > > https://www.flashrom.org/mailman/listinfo/flashrom > > > > -- > David Hendricks (dhendrix) > Systems Software Engineer, Google Inc.

1 0

Apollo Lake
by Tim Lewis 09 Nov '16

09 Nov '16

On the most recent version of the Chromium flashrom effort, there was a patch for Apollo Lake. I have applied it to the latest, fixed up one issue in the get_target_bus_from_chipset() to return the right BBS strapping. It finds the Winbond chip and starts to read, and gets an error when reading the ROM using the HWSEQ style. I have tracked it down to the function that waits for complete, where it fails. Any thoughts? Thanks, Tim Lewis P.S. I have this working with other flash utilities, so I know that the hardware is working and the flash part is present and responds. FAILED.p@p-desktop:~/Desktop/Blinkflash-Linux64-100.00.00.03$ sudo ./flashrom -p internal -r 123.bin -VV flashrom v0.9.7-unknown on Linux 4.4.0-21-generic (x86_64), built with libpci 3.2.1, GCC 4.8.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Initializing internal programmer No coreboot table found. get_target_bus_from_chipset() returns 0x10. Found chipset "Intel Apollolake" with PCI ID 8086:5af0. Enabling flash write... Vendor ID: 8086, Device ID: 5a96, BAR: fed01000 BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x89 SPI BAR is = 0xfed01000 GCS = 0x89: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x0 (SPI) SPIBAR = 0xfed01000 + 0x0000 0x04: 0x3f00e000 (HSFSC) WARNING: SPI Configuration Lockdown activated. 0x08: 0x00000000 (FADDR) 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 (FREG0: Flash Descriptor) 0x00000000-0x00000fff is read-write 0x58: 0x06fe0001 (FREG1: BIOS) 0x00001000-0x006fefff is read-write 0x5C: 0x00007fff (FREG2: Management Engine) Management Engine region is unused. 0x60: 0x00007fff (FREG3: Gigabit Ethernet) Gigabit Ethernet region is unused. 0x64: 0x00007fff (FREG4: Platform Data) Platform Data region is unused. 0x84: 0x00000000 (PR0, unused) 0x88: 0x00000000 (PR1, unused) 0x8C: 0x00000000 (PR2, unused) 0x90: 0x00000000 (PR3, unused) 0x94: 0x00000000 (PR4, unused) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x00040003 FLMAP1 0x13100208 FLMAP2 0x00000000 --- Details --- NR (Number of Regions): 1 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 19 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x080 MSL/PSL (MCH/PROC Strap Length): 0 FMSBA (Flash MCH/PROC Strap Base Address): 0x000 === Component Section === FLCOMP 0x649c02f4 FLILL 0xad604221 --- Details --- Component 1 density: 8 MB Component 2 is not used. Read Clock Frequency: reserved Read ID and Status Clock Freq.: 50 MHz Write and Erase Clock Freq.: 50 MHz Fast Read is supported. Fast Read Clock Frequency: 50 MHz Invalid instruction 0: 0x21 Invalid instruction 1: 0x42 Invalid instruction 2: 0x60 Invalid instruction 3: 0xad === Region Section === FLREG0 0x00000000 FLREG1 0x06fe0001 --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00001000 - 0x006fefff === Master Section === FLMSTR1 0xffffff00 FLMSTR2 0xffffff00 FLMSTR3 0x7ff7ff00 --- Details --- Descr. BIOS ME GbE Platf. BIOS rw rw rw rw rw ME rw rw rw rw rw GbE rw rw rw w rw SPI Read Configuration: prefetching enabled, caching enabled, OK. This programmer supports the following protocols: FWH, Programmer-specific. Probing for Winbond W25Q128.V, 0 kB: Found 1 attached SPI flash chip with a density of 8192 kB. There are 2048 erase blocks with 4096 B each. Found Winbond flash chip "W25Q128.V" (8192 kB, Programmer-specific) at physical address 0x0. Found Winbond flash chip "W25Q128.V" (8192 kB, Programmer-specific). === The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... Reading 8388608 bytes starting at 0x000000. Transaction error between offset 0x00000000 and 0x0000003f (= 0x00000000 + 63) failed to read 0x0-0x7fffff Read operation failed! FAILED.p@p-desktop:~/Desktop/Blinkflash-Linux64-100.00.00.03$

2 1

Re: [flashrom] [PATCH] RFC: enable flashrom to write images of arbitrary size
by Nico Huber 09 Nov '16

09 Nov '16

Hi all, On 09.11.2016 00:20, Charlotte Plusplus wrote: > Hello > > That is very interesting. Do you have a way to automate that? > > I am testing ram stuff with coreboot, I don't need to flash a full 8MB > image. I could just pass a -i of the cbfs content to only change the > ramstage, and do a manual md5 of the various parts contained to only target > the difference, but it seems a bit tedious. > > It would be nice to do have a way to do kind of diff between the currenttly > flashed image and the desired image, and only flash the required changes. that is exactly what stock flashrom already does. The only thing that's not optimized is the reading. It currently always reads the whole flash twice, once before the flashing to create the diff, once for verifica- tion (no matter what the layout says). I did something to improve that for stock flashrom, see https://www.flashrom.org/pipermail/flashrom/2016-May/014629.html and the fourteen patches surrounding it. The magic there would be the -A option (don't read All). Nico > > Charlotte > > On Tue, Nov 8, 2016 at 2:22 PM, David Hendricks via flashrom < > flashrom(a)flashrom.org> wrote: > >> Hi Peter, >> Thanks for the patch! However, I suspect this will not be accepted >> since the size check is an important safety measure for the general >> use case. >> >> In general layout files should be used for this sort of thing. The way >> we've gone about this in the chromium.org branch is to augment the -i >> syntax to allow the user to specify a region and corresponding file, >> and we also added a "--fast-verify" mode to only verify regions which >> were targeted. So for example you could do "flashrom -p <programmer> >> -l <layout_file> -i region:filename.bin --fast-verify --ignore-fmap >> -w" which will write filename.bin to the targeted region and verify >> only that region. >> >> Details here: https://www.chromium.org/chromium-os/packages/cros- >> flashrom#TOC-Partial-Reads-and-Writes >> . LMK if this is any help. >> >> >> >> On Mon, Nov 7, 2016 at 1:00 PM, Peter Mamonov <pmamonov(a)gmail.com> wrote: >>> Flashrom restricts an image size to be equal to a ROM capacity. This is >>> inconvenient in case of large and slow ROM chips, when only part of the >> ROM >>> should be updated. This patch removes this restriction in a >> quick-and-dirty >>> manner. >>> >>> Signed-off-by: Peter Mamonov <pmamonov(a)gmail.com> >>> --- >>> flashrom.c | 26 +++++++++++++++----------- >>> 1 file changed, 15 insertions(+), 11 deletions(-) >>> >>> diff --git a/flashrom.c b/flashrom.c >>> index d51a44c..f805e00 100644 >>> --- a/flashrom.c >>> +++ b/flashrom.c >>> @@ -1255,30 +1255,30 @@ int read_buf_from_file(unsigned char *buf, >> unsigned long size, >>> >>> if ((image = fopen(filename, "rb")) == NULL) { >>> msg_gerr("Error: opening file \"%s\" failed: %s\n", >> filename, strerror(errno)); >>> - return 1; >>> + return -1; >>> } >>> if (fstat(fileno(image), &image_stat) != 0) { >>> msg_gerr("Error: getting metadata of file \"%s\" failed: >> %s\n", filename, strerror(errno)); >>> fclose(image); >>> - return 1; >>> + return -1; >>> } >>> - if (image_stat.st_size != size) { >>> + if (image_stat.st_size > size) { >>> msg_gerr("Error: Image size (%jd B) doesn't match the >> flash chip's size (%lu B)!\n", >>> (intmax_t)image_stat.st_size, size); >>> - fclose(image); >>> - return 1; >>> + return -1; >>> } >>> + size = image_stat.st_size; >>> numbytes = fread(buf, 1, size, image); >>> if (fclose(image)) { >>> msg_gerr("Error: closing file \"%s\" failed: %s\n", >> filename, strerror(errno)); >>> - return 1; >>> + return -1; >>> } >>> if (numbytes != size) { >>> msg_gerr("Error: Failed to read complete file. Got %ld >> bytes, " >>> "wanted %ld!\n", numbytes, size); >>> - return 1; >>> + return -1; >>> } >>> - return 0; >>> + return size; >>> #endif >>> } >>> >>> @@ -1481,7 +1481,10 @@ static int walk_eraseregions(struct flashctx >> *flash, int erasefunction, >>> * members so the loop below won't be executed for them. >>> */ >>> len = eraser.eraseblocks[i].size; >>> - for (j = 0; j < eraser.eraseblocks[i].count; j++) { >>> + for (j = 0; >>> + j < eraser.eraseblocks[i].count && >>> + start + len <= flash->chip->total_size * 1024; >>> + j++) { >>> /* Print this for every block except the first >> one. */ >>> if (i || j) >>> msg_cdbg(", "); >>> @@ -1988,11 +1991,12 @@ int doit(struct flashctx *flash, int force, >> const char *filename, int read_it, >>> } >>> >>> if (write_it || verify_it) { >>> - if (read_buf_from_file(newcontents, size, filename)) { >>> + size = read_buf_from_file(newcontents, size, filename); >>> + if (size < 0) { >>> ret = 1; >>> goto out; >>> } >>> - >>> + flash->chip->total_size = size / 1024; /* FIXME */ >>> #if CONFIG_INTERNAL == 1 >>> if (programmer == PROGRAMMER_INTERNAL && >> cb_check_image(newcontents, size) < 0) { >>> if (force_boardmismatch) { >>> -- >>> 2.1.4 >>> >>> >>> _______________________________________________ >>> flashrom mailing list >>> flashrom(a)flashrom.org >>> https://www.flashrom.org/mailman/listinfo/flashrom >> >> >> >> -- >> David Hendricks (dhendrix) >> Systems Software Engineer, Google Inc. >> >> _______________________________________________ >> flashrom mailing list >> flashrom(a)flashrom.org >> https://www.flashrom.org/mailman/listinfo/flashrom >> > > > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > https://www.flashrom.org/mailman/listinfo/flashrom >

1 0

Re: [flashrom] [PATCH] RFC: enable flashrom to write images of arbitrary size
by Charlotte Plusplus 09 Nov '16

09 Nov '16

Hello That is very interesting. Do you have a way to automate that? I am testing ram stuff with coreboot, I don't need to flash a full 8MB image. I could just pass a -i of the cbfs content to only change the ramstage, and do a manual md5 of the various parts contained to only target the difference, but it seems a bit tedious. It would be nice to do have a way to do kind of diff between the currenttly flashed image and the desired image, and only flash the required changes. Charlotte On Tue, Nov 8, 2016 at 2:22 PM, David Hendricks via flashrom < flashrom(a)flashrom.org> wrote: > Hi Peter, > Thanks for the patch! However, I suspect this will not be accepted > since the size check is an important safety measure for the general > use case. > > In general layout files should be used for this sort of thing. The way > we've gone about this in the chromium.org branch is to augment the -i > syntax to allow the user to specify a region and corresponding file, > and we also added a "--fast-verify" mode to only verify regions which > were targeted. So for example you could do "flashrom -p <programmer> > -l <layout_file> -i region:filename.bin --fast-verify --ignore-fmap > -w" which will write filename.bin to the targeted region and verify > only that region. > > Details here: https://www.chromium.org/chromium-os/packages/cros- > flashrom#TOC-Partial-Reads-and-Writes > . LMK if this is any help. > > > > On Mon, Nov 7, 2016 at 1:00 PM, Peter Mamonov <pmamonov(a)gmail.com> wrote: > > Flashrom restricts an image size to be equal to a ROM capacity. This is > > inconvenient in case of large and slow ROM chips, when only part of the > ROM > > should be updated. This patch removes this restriction in a > quick-and-dirty > > manner. > > > > Signed-off-by: Peter Mamonov <pmamonov(a)gmail.com> > > --- > > flashrom.c | 26 +++++++++++++++----------- > > 1 file changed, 15 insertions(+), 11 deletions(-) > > > > diff --git a/flashrom.c b/flashrom.c > > index d51a44c..f805e00 100644 > > --- a/flashrom.c > > +++ b/flashrom.c > > @@ -1255,30 +1255,30 @@ int read_buf_from_file(unsigned char *buf, > unsigned long size, > > > > if ((image = fopen(filename, "rb")) == NULL) { > > msg_gerr("Error: opening file \"%s\" failed: %s\n", > filename, strerror(errno)); > > - return 1; > > + return -1; > > } > > if (fstat(fileno(image), &image_stat) != 0) { > > msg_gerr("Error: getting metadata of file \"%s\" failed: > %s\n", filename, strerror(errno)); > > fclose(image); > > - return 1; > > + return -1; > > } > > - if (image_stat.st_size != size) { > > + if (image_stat.st_size > size) { > > msg_gerr("Error: Image size (%jd B) doesn't match the > flash chip's size (%lu B)!\n", > > (intmax_t)image_stat.st_size, size); > > - fclose(image); > > - return 1; > > + return -1; > > } > > + size = image_stat.st_size; > > numbytes = fread(buf, 1, size, image); > > if (fclose(image)) { > > msg_gerr("Error: closing file \"%s\" failed: %s\n", > filename, strerror(errno)); > > - return 1; > > + return -1; > > } > > if (numbytes != size) { > > msg_gerr("Error: Failed to read complete file. Got %ld > bytes, " > > "wanted %ld!\n", numbytes, size); > > - return 1; > > + return -1; > > } > > - return 0; > > + return size; > > #endif > > } > > > > @@ -1481,7 +1481,10 @@ static int walk_eraseregions(struct flashctx > *flash, int erasefunction, > > * members so the loop below won't be executed for them. > > */ > > len = eraser.eraseblocks[i].size; > > - for (j = 0; j < eraser.eraseblocks[i].count; j++) { > > + for (j = 0; > > + j < eraser.eraseblocks[i].count && > > + start + len <= flash->chip->total_size * 1024; > > + j++) { > > /* Print this for every block except the first > one. */ > > if (i || j) > > msg_cdbg(", "); > > @@ -1988,11 +1991,12 @@ int doit(struct flashctx *flash, int force, > const char *filename, int read_it, > > } > > > > if (write_it || verify_it) { > > - if (read_buf_from_file(newcontents, size, filename)) { > > + size = read_buf_from_file(newcontents, size, filename); > > + if (size < 0) { > > ret = 1; > > goto out; > > } > > - > > + flash->chip->total_size = size / 1024; /* FIXME */ > > #if CONFIG_INTERNAL == 1 > > if (programmer == PROGRAMMER_INTERNAL && > cb_check_image(newcontents, size) < 0) { > > if (force_boardmismatch) { > > -- > > 2.1.4 > > > > > > _______________________________________________ > > flashrom mailing list > > flashrom(a)flashrom.org > > https://www.flashrom.org/mailman/listinfo/flashrom > > > > -- > David Hendricks (dhendrix) > Systems Software Engineer, Google Inc. > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > https://www.flashrom.org/mailman/listinfo/flashrom >

1 0

[PATCH] RFC: enable flashrom to write images of arbitrary size
by Peter Mamonov 08 Nov '16

08 Nov '16

Flashrom restricts an image size to be equal to a ROM capacity. This is inconvenient in case of large and slow ROM chips, when only part of the ROM should be updated. This patch removes this restriction in a quick-and-dirty manner. Signed-off-by: Peter Mamonov <pmamonov(a)gmail.com> --- flashrom.c | 26 +++++++++++++++----------- 1 file changed, 15 insertions(+), 11 deletions(-) diff --git a/flashrom.c b/flashrom.c index d51a44c..f805e00 100644 --- a/flashrom.c +++ b/flashrom.c @@ -1255,30 +1255,30 @@ int read_buf_from_file(unsigned char *buf, unsigned long size, if ((image = fopen(filename, "rb")) == NULL) { msg_gerr("Error: opening file \"%s\" failed: %s\n", filename, strerror(errno)); - return 1; + return -1; } if (fstat(fileno(image), &image_stat) != 0) { msg_gerr("Error: getting metadata of file \"%s\" failed: %s\n", filename, strerror(errno)); fclose(image); - return 1; + return -1; } - if (image_stat.st_size != size) { + if (image_stat.st_size > size) { msg_gerr("Error: Image size (%jd B) doesn't match the flash chip's size (%lu B)!\n", (intmax_t)image_stat.st_size, size); - fclose(image); - return 1; + return -1; } + size = image_stat.st_size; numbytes = fread(buf, 1, size, image); if (fclose(image)) { msg_gerr("Error: closing file \"%s\" failed: %s\n", filename, strerror(errno)); - return 1; + return -1; } if (numbytes != size) { msg_gerr("Error: Failed to read complete file. Got %ld bytes, " "wanted %ld!\n", numbytes, size); - return 1; + return -1; } - return 0; + return size; #endif } @@ -1481,7 +1481,10 @@ static int walk_eraseregions(struct flashctx *flash, int erasefunction, * members so the loop below won't be executed for them. */ len = eraser.eraseblocks[i].size; - for (j = 0; j < eraser.eraseblocks[i].count; j++) { + for (j = 0; + j < eraser.eraseblocks[i].count && + start + len <= flash->chip->total_size * 1024; + j++) { /* Print this for every block except the first one. */ if (i || j) msg_cdbg(", "); @@ -1988,11 +1991,12 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it, } if (write_it || verify_it) { - if (read_buf_from_file(newcontents, size, filename)) { + size = read_buf_from_file(newcontents, size, filename); + if (size < 0) { ret = 1; goto out; } - + flash->chip->total_size = size / 1024; /* FIXME */ #if CONFIG_INTERNAL == 1 if (programmer == PROGRAMMER_INTERNAL && cb_check_image(newcontents, size) < 0) { if (force_boardmismatch) { -- 2.1.4

2 1

Invalid size. Asus P8Z77-V LX. W25Q64.V
by Лейба Бронштейн 08 Nov '16

08 Nov '16

[ 0.000000] DMI: System manufacturer System Product Name/P8Z77-V LX, BIOS 1502 11/09/2012 /usr/local/sbin/flashrom -p internal -w P8Z77-V-LX-ASUS-2501.CAP flashrom v0.9.9-r1954 on Linux 4.4.19-1-pve (x86_64) flashrom is free software, get the source code at https://flashrom.org Calibrating delay loop... OK. Found chipset "Intel Z77". Enabling flash write... Warning: SPI Configuration Lockdown activated. OK. Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Error: Image size (8390656 B) doesn't match the flash chip's size (8388608 B)!

1 0

Re: [flashrom] FAILED: W25Q64.V bios flash on a ThinkPad
by Charlotte Plusplus 06 Nov '16

06 Nov '16

In case someone else has the same problem, I found a solution. It is weird but works reliably for me: the pins must not be connected one by one to the J100 header, but all at once. If you use floating wires, use duct tape to shape them into a plug. Insert it swiftly. Then it works fine 100% of the time. I got the idea after reading about timing issues on: http://dangerousprototypes.com/forum/viewtopic.php?f=40&t=4157 https://www.raspberrypi.org/forums/viewtopic.php?f=41&t=123825 I have no idea why it works, but it works. On 11/4/16, Charlotte Plusplus <pluspluscharlotte(a)gmail.com> wrote: > Hello > > I am trying to flash a W25Q64.V in a Thinkpad W520 using a Raspberry Pi > To make it easier, I soldered an ISP connector on the motherboard J100 > connector (https://www.coreboot.org/Board:lenovo/t520#Flashing) to > make sure I would have a good electrical connection. > WP and HOLD were left floating, and I used the 3.3V from the Raspberry Pi > pin 1. > The electrical connection was good: I could read the flash. I did it 4 > times to make sure the MD5 matched. They did. The strings inside the > flash matched the bios version, and ifdtool did recognize the image. > > When I tried to flash however, something weird happened: > > flashrom -w coreboot.pre apt-ge-p linux_spi:dev=/dev/spidev0.0 > Calibrating delay loop... delay loop is unreliable, trying to continue OK. > Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on linux_spi. > Reading old flash chip contents... done. > Erasing and writing flash chip... Erase/write done. > Verifying flash... FAILED at 0x007bbe00! Expected=0x24, Found=0x98, > failed byte count from 0x00000000-0x007fffff: 0x8e4 > Your flash chip is in an unknown state. > Please report this on IRC at chat.freenode.net (channel #flashrom) or > mail flashrom(a)flashrom.org, thanks! > > Ever since, I can't access the chip. The laptop can't boot. The > original image can't be restored. > > Whenever I try to read the flash using the exact same command line as > before, I get: > > flashrom -r w520-bios-backup.bin -V -p linux_spi:dev=/dev/spidev0.0 > (...) > Probing for Winbond W25Q64.W, 8192 kB: RDID byte 0 parity violation. > probe_spi_rdid_generic: id1 0x00, id2 0x00 > (...) > Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI). > > Funny enough, if I don't connect any cable to the raspberry, I get the > exact same error message. > > I tried various configuration: with the raspberry pi power, with WP > and HOLD set to high, with external power and WP and HOLD set to high > - nothing works. > I checked the W25Q64 specsheet > (ttps://cdn.sparkfun.com/datasheets/Dev/Teensy/w25q64fv.pdf), the > system board schematics > (http://kythuatphancung.vn/uploads/download/5165b_Wistron_Kendo-3_WS_-_10222…) > but I just don't understand what is happening. > > Any suggestion?? I have flashed with this raspberry before, and it > never when bad to the point that I could no longer even read the chip. > > I am afraid something really wrong happened. Any help is appreciated. >

1 0

FAILED: W25Q64.V bios flash on a ThinkPad
by Charlotte Plusplus 04 Nov '16

04 Nov '16

Hello I am trying to flash a W25Q64.V in a Thinkpad W520 using a Raspberry Pi To make it easier, I soldered an ISP connector on the motherboard J100 connector (https://www.coreboot.org/Board:lenovo/t520#Flashing) to make sure I would have a good electrical connection. WP and HOLD were left floating, and I used the 3.3V from the Raspberry Pi pin 1. The electrical connection was good: I could read the flash. I did it 4 times to make sure the MD5 matched. They did. The strings inside the flash matched the bios version, and ifdtool did recognize the image. When I tried to flash however, something weird happened: flashrom -w coreboot.pre apt-ge-p linux_spi:dev=/dev/spidev0.0 Calibrating delay loop... delay loop is unreliable, trying to continue OK. Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) on linux_spi. Reading old flash chip contents... done. Erasing and writing flash chip... Erase/write done. Verifying flash... FAILED at 0x007bbe00! Expected=0x24, Found=0x98, failed byte count from 0x00000000-0x007fffff: 0x8e4 Your flash chip is in an unknown state. Please report this on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org, thanks! Ever since, I can't access the chip. The laptop can't boot. The original image can't be restored. Whenever I try to read the flash using the exact same command line as before, I get: flashrom -r w520-bios-backup.bin -V -p linux_spi:dev=/dev/spidev0.0 (...) Probing for Winbond W25Q64.W, 8192 kB: RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x00 (...) Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI). Funny enough, if I don't connect any cable to the raspberry, I get the exact same error message. I tried various configuration: with the raspberry pi power, with WP and HOLD set to high, with external power and WP and HOLD set to high - nothing works. I checked the W25Q64 specsheet (ttps://cdn.sparkfun.com/datasheets/Dev/Teensy/w25q64fv.pdf), the system board schematics (http://kythuatphancung.vn/uploads/download/5165b_Wistron_Kendo-3_WS_-_10222…) but I just don't understand what is happening. Any suggestion?? I have flashed with this raspberry before, and it never when bad to the point that I could no longer even read the chip. I am afraid something really wrong happened. Any help is appreciated.

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom