- flashrom - mail.coreboot.org

[commit] r1049 - trunk
by repository service 17 Jun '10

17 Jun '10

Author: stuge Date: Thu Jun 17 02:01:56 2010 New Revision: 1049 URL: http://flashrom.org/trac/coreboot/changeset/1049 Log: Set maximum flash size for 3Com NICs to 128kb = 1Mbit This fact was already documented on http://flashrom.org/NIC3Com Signed-off-by: Peter Stuge <peter(a)stuge.se> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/nic3com.c Modified: trunk/nic3com.c ============================================================================== --- trunk/nic3com.c Mon Jun 14 20:40:59 2010 (r1048) +++ trunk/nic3com.c Thu Jun 17 02:01:56 2010 (r1049) @@ -81,6 +81,7 @@ OUTW(SELECT_REG_WINDOW + 0, io_base_addr + INT_STATUS); buses_supported = CHIP_BUSTYPE_PARALLEL; + max_rom_decode.parallel = 128 * 1024; return 0; }

1 0

[PATCH] SPI flashing speedup
by Carl-Daniel Hailfinger 17 Jun '10

17 Jun '10

I know of no supported SPI chip which would require delays for any operation. The delays in our SPI code are only there to reduce load on the SPI bus. As such, they might be a good idea for shared flash, but I'm not too convinced of that either. For all external programmers, delays between commands are 100% pointless unless required by the flash chip (and I don't know of any such requirements). Michael, I'd like to hear your thoughts on the impact of reading the status register in a tight loop instead of sleeping in between for systems which use flash translation (e.g. by EC). There are two options how we can handle this: - Remove the delays completely. - Mark the delays as optional, e.g. programmer_odelay() and let it default to a nop. This patch removes the delays. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-spi_nodelay/spi25.c =================================================================== --- flashrom-spi_nodelay/spi25.c (Revision 1048) +++ flashrom-spi_nodelay/spi25.c (Arbeitskopie) @@ -455,11 +455,11 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 1-85 s, so wait in 1 s steps. + * This usually takes 1-85 s. */ /* FIXME: We assume spi_read_status_register will never fail. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(1000 * 1000); + /* do nothing */; if (check_erased_range(flash, 0, flash->total_size * 1024)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -500,11 +500,11 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 1-85 s, so wait in 1 s steps. + * This usually takes 1-85 s. */ /* FIXME: We assume spi_read_status_register will never fail. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(1000 * 1000); + /* do nothing */; if (check_erased_range(flash, 0, flash->total_size * 1024)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -545,10 +545,10 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 100-4000 ms, so wait in 100 ms steps. + * This usually takes 100-4000 ms. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(100 * 1000); + /* do nothing */; if (check_erased_range(flash, addr, blocklen)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -594,10 +594,10 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 100-4000 ms, so wait in 100 ms steps. + * This usually takes 100-4000 ms. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(100 * 1000); + /* do nothing */; if (check_erased_range(flash, addr, blocklen)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -641,10 +641,10 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 100-4000 ms, so wait in 100 ms steps. + * This usually takes 100-4000 ms. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(100 * 1000); + /* do nothing */; if (check_erased_range(flash, addr, blocklen)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -709,10 +709,10 @@ return result; } /* Wait until the Write-In-Progress bit is cleared. - * This usually takes 15-800 ms, so wait in 10 ms steps. + * This usually takes 15-800 ms. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(10 * 1000); + /* do nothing */; if (check_erased_range(flash, addr, blocklen)) { msg_cerr("ERASE FAILED!\n"); return -1; @@ -977,7 +977,7 @@ if (rc) break; while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(10); + /* do nothing */; } if (rc) break; @@ -1010,7 +1010,7 @@ if (result) return 1; while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(10); + /* do nothing */; } return 0; @@ -1044,13 +1044,13 @@ return result; spi_send_command(6, 0, w, NULL); while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(5); /* SST25VF040B Tbp is max 10us */ + /* do nothing */; while (pos < size) { w[1] = buf[pos++]; w[2] = buf[pos++]; spi_send_command(3, 0, w, NULL); while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(5); /* SST25VF040B Tbp is max 10us */ + /* do nothing */; } spi_write_disable(); return 0; Index: flashrom-spi_nodelay/it87spi.c =================================================================== --- flashrom-spi_nodelay/it87spi.c (Revision 1048) +++ flashrom-spi_nodelay/it87spi.c (Arbeitskopie) @@ -304,7 +304,7 @@ * This usually takes 1-10 ms, so wait in 1 ms steps. */ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) - programmer_delay(1000); + /* do nothing */; return 0; } Index: flashrom-spi_nodelay/wbsio_spi.c =================================================================== --- flashrom-spi_nodelay/wbsio_spi.c (Revision 1048) +++ flashrom-spi_nodelay/wbsio_spi.c (Arbeitskopie) @@ -163,7 +163,6 @@ OUTB(writearr[0], wbsio_spibase); OUTB(mode, wbsio_spibase + 1); - programmer_delay(10); if (!readcnt) return 0; -- http://www.hailfinger.org/

3 3

Flashing
by Damon Andrew Keller 16 Jun '10

16 Jun '10

Hello, Let me get this right, did I just kill my server's BIOS by running this flashrom command? I thought I was testing it out so that I can email you the data? I'm going to be gone for about a year and I was hoping to do remote work for it. GOD I hope the lights don't go out... help.... -Damon CoreBoot This is what was found on the server: superiotool -dV Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627HF/F/HG/G (id=0x52, rev=0x17) at 0x2e Register dump: idx 02 20 21 22 23 24 25 26 28 29 2a 2b 2c 2e 2f val ff 52 17 ff fe 84 00 00 00 00 7d c1 ff 00 ff def 00 52 NA ff 00 MM 00 00 00 00 7c c0 00 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 00 00 00 00 04 0e 00 ff 00 00 def 01 03 f0 06 02 0e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 00 00 00 00 03 3b def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 00 00 00 00 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 00 00 00 04 5d def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 80 def 01 00 60 00 64 01 0c 80 LDN 0x06 (Consumer IR) idx 30 60 61 70 val 00 00 00 00 def 00 00 00 00 LDN 0x07 (Game port, MIDI port, GPIO 1) idx 30 60 61 62 63 70 f0 f1 f2 val 01 00 00 00 00 00 ff 00 00 def 00 02 01 03 30 09 ff 00 00 LDN 0x08 (GPIO 2, Watchdog timer) idx 30 f0 f1 f2 f3 f5 f6 f6 f7 val 01 ff 00 00 00 00 00 00 00 def 00 ff 00 00 00 00 00 00 00 LDN 0x09 (GPIO 3) idx 30 f0 f1 f2 f3 val 01 ff 00 00 40 def 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 f0 f1 f3 f4 f6 f7 f9 fe ff val 00 00 40 03 14 2f 20 00 00 00 00 af 30 00 00 00 01 00 00 def 00 00 00 00 NA NA 00 00 00 00 00 00 00 00 00 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 val 01 02 90 00 00 def 00 00 00 00 00 flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "http://www.abit.com.tw/" DMI string baseboard-product-name: "NF7-S/NF7,NF7-V (nVidia-nForce2)" DMI string baseboard-version: "2.X,1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA NForce2", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 550M loops per second, 100 myus = 150 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xfa, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x44, id2 0xc1 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === No operations were specified. root@inas:~# flashrom -rV flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "http://www.abit.com.tw/" DMI string baseboard-product-name: "NF7-S/NF7,NF7-V (nVidia-nForce2)" DMI string baseboard-version: "2.X,1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA NForce2", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 585M loops per second, 100 myus = 160 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xfa, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x44, id2 0xc1 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. === root@inas:~# flashrom -wV flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "http://www.abit.com.tw/" DMI string baseboard-product-name: "NF7-S/NF7,NF7-V (nVidia-nForce2)" DMI string baseboard-version: "2.X,1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA NForce2", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 545M loops per second, 100 myus = 149 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xfa, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x44, id2 0xc1 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. === root@inas:~# flashrom -EV flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "http://www.abit.com.tw/" DMI string baseboard-product-name: "NF7-S/NF7,NF7-V (nVidia-nForce2)" DMI string baseboard-version: "2.X,1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA NForce2", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 549M loops per second, 100 myus = 150 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x49, id2 0x4d, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xfa, id2 0xfc, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x44, id2 0xc1 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0x44, id2 0xc1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x9d, id2 0x6e Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x6e Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. === This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x00000fff: 0x40a ERASE FAILED! Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0000ffff: 0x40a ERASE FAILED! Looking at blockwise erase function 2... trying... 0x000000-0x07ffff, ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x4662a ERASE FAILED! Looking at blockwise erase function 3... not defined. Looking for another erase function. Looking at blockwise erase function 4... not defined. Looking for another erase function. FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF!

2 1

Flash write verified on Emerson,ATCA-7360/R1.0/6E
by Ramakrishna.Koduri＠emerson.com 15 Jun '10

15 Jun '10

Hi All, The Atmel AT25DF321 flash is programmed & verified with flashrom v0.9.2-r1001 on Emerson,ATCA-7360/R1.0/6E and the output is stated below: The flash chip(Atmel AT25DF321) is present on Intel I/O controller HUB (Intel ICH10R). It could program the device using the internal programmer with erase function type: 2. The probed flash is the one soldered down on the board. It went on well. Thanks for the efforts and the software. ======================================================================== ============== [root@localhost flashrom-0.9.2]# ./flashrom -V -l layout -w atca7360-bios.img -i part_2000_4000.log flashrom v0.9.2-r1001 on Linux 2.6.18-194.el5PAE (i686), built with libpci 2.2.3, GCC 4.1.2 20080704 (Red Hat 4.1.2-48) flashrom is free software, get the source code at http://www.flashrom.org romlayout 00002000 - 00003fff named /mnt/root/ramki/flashrom-0.9.2/part_2000_4000.log Looking for "part_2000_4000.log"... not found. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Emerson" DMI string system-product-name: "PCA,ATCA-7360/R1.0/6E " DMI string system-version: "R1.0 " DMI string baseboard-manufacturer: "Emerson" DMI string baseboard-product-name: "ATCA-7360/7365" DMI string baseboard-version: "0106865F01A " DMI string chassis-type: "" Found chipset "Intel ICH10R", enabling flash write... 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x4 0x7fffffff/0x7fffffff FWH IDSEL: 0x5 0x7fffffff/0x7fffffff FWH IDSEL: 0x6 0x7fffffff/0x7fffffff FWH IDSEL: 0x7 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled Maximum FWH chip size: 0x380000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x9 Root Complex Register Block address = 0xfed1c000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) FLOCKDN 0, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00001b1b (FRAP) BMWAG 0, BMRAG 0, BRWA 27, BRRA 27 0x54: 0x00010000 (FREG0) 0x58: 0x03ff0080 (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00030002 (FREG3) 0x64: 0x007f0004 (FREG4) 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x007f100c (SSFS, SSFC) 0x94: 0x0006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00004000 (FDOC) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching enabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 1091M loops per second, 10 myus = 10 us, 100 myus = 103 us, 1000 myus = 1029 us, 10000 myus = 10073 us, OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Chip status register is 10 Found chip "Atmel AT25DF321" (4096 KB, SPI) at physical address 0xffc00000. Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Eon EN29F010, 128 KB: skipped. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0x0, id2 0x0 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0x0, id2 0x0 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x40, id2 0x11, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS S29C31004T, 512 KB: skipped. Probing for SyncMOS S29C51001T, 128 KB: skipped. Probing for SyncMOS S29C51002T, 256 KB: skipped. Probing for SyncMOS S29C51004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for EON unknown EON SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0x1f, id2 0x4700 Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0x0, id2 0x0 === This flash part has status UNTESTED for operations: ERASE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Thanks for your help! === Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Some block protection in effect, disabling Erasing flash before programming... Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ich_spi_send_multicommand: FIXME: Add on-the-fly reprogramming of the chipset opcode list. Invalid OPCODE 0x20 spi_block_erase_20 failed during command execution at address 0x0 Looking at blockwise erase function 1... trying... 0x000000-0x007fff, ich_spi_send_multicommand: FIXME: Add on-the-fly reprogramming of the chipset opcode list. Invalid OPCODE 0x52 spi_block_erase_52 failed during command execution at address 0x0 Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, 0x010000-0x01ffff, 0x020000-0x02ffff, 0x030000-0x03ffff, 0x040000-0x04ffff, 0x050000-0x05ffff, 0x060000-0x06ffff, 0x070000-0x07ffff, 0x080000-0x08ffff, 0x090000-0x09ffff, 0x0a0000-0x0affff, 0x0b0000-0x0bffff, 0x0c0000-0x0cffff, 0x0d0000-0x0dffff, 0x0e0000-0x0effff, 0x0f0000-0x0fffff, 0x100000-0x10ffff, 0x110000-0x11ffff, 0x120000-0x12ffff, 0x130000-0x13ffff, 0x140000-0x14ffff, 0x150000-0x15ffff, 0x160000-0x16ffff, 0x170000-0x17ffff, 0x180000-0x18ffff, 0x190000-0x19ffff, 0x1a0000-0x1affff, 0x1b0000-0x1bffff, 0x1c0000-0x1cffff, 0x1d0000-0x1dffff, 0x1e0000-0x1effff, 0x1f0000-0x1fffff, 0x200000-0x20ffff, 0x210000-0x21ffff, 0x220000-0x22ffff, 0x230000-0x23ffff, 0x240000-0x24ffff, 0x250000-0x25ffff, 0x260000-0x26ffff, 0x270000-0x27ffff, 0x280000-0x28ffff, 0x290000-0x29ffff, 0x2a0000-0x2affff, 0x2b0000-0x2bffff, 0x2c0000-0x2cffff, 0x2d0000-0x2dffff, 0x2e0000-0x2effff, 0x2f0000-0x2fffff, 0x300000-0x30ffff, 0x310000-0x31ffff, 0x320000-0x32ffff, 0x330000-0x33ffff, 0x340000-0x34ffff, 0x350000-0x35ffff, 0x360000-0x36ffff, 0x370000-0x37ffff, 0x380000-0x38ffff, 0x390000-0x39ffff, 0x3a0000-0x3affff, 0x3b0000-0x3bffff, 0x3c0000-0x3cffff, 0x3d0000-0x3dffff, 0x3e0000-0x3effff, 0x3f0000-0x3fffff, SUCCESS. done. Programming page: COMPLETE. Verifying flash... VERIFIED. -------------- ICH10R informatio -------------- 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller Subsystem: Artesyn Communication Products Unknown device 004f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [e0] Vendor Specific Information ======================================================================== ============== With thanks & regards, Ramakrishna Kvv Embedded Computing Emerson Network Power T +9140 66747045 M + 919246659136 ramakrishna.koduri(a)emerson.com <blocked::mailto:ramakrishna.koduri@emerson.com> www.emersonnetworkpower.com/embeddedcomputing <http://www.emersonnetworkpower.com/embeddedcomputing>

1 0

Unbricking with the help of Arduino
by Mattias Mattsson 15 Jun '10

15 Jun '10

Hi, Maybe this is of interest to flashrom developers: http://hackaday.com/2010/06/14/unbricking-with-the-help-of-arduino/ Cheers! -mattias PS. And also: sorry for not testing the write enable patch for HP VL420 in a timely manner. Will do ASAP.

1 0

[PATCH] Override incompatible CONFIG_FOO for DOS
by Carl-Daniel Hailfinger 14 Jun '10

14 Jun '10

Override incompatible CONFIG_FOO settings for DOS. This allows you to specify CONFIG_FOO=yes for all drivers and still get only those which compile under DOS. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-dos_override_incompatible_config_foo/Makefile =================================================================== --- flashrom-dos_override_incompatible_config_foo/Makefile (Revision 1031) +++ flashrom-dos_override_incompatible_config_foo/Makefile (Arbeitskopie) @@ -50,9 +50,12 @@ endif ifeq ($(OS_ARCH), DOS) CPPFLAGS += -I../libgetopt -I../libpci/include -# Bus Pirate and Serprog are not supported under DOS. -CONFIG_BUSPIRATE_SPI = no -CONFIG_SERPROG = no +# Bus Pirate and Serprog are not supported under DOS (missing serial support). +override CONFIG_BUSPIRATE_SPI = no +override CONFIG_SERPROG = no +# Dediprog and FT2232 are not supported under DOS (missing USB support). +override CONFIG_DEDIPROG = no +override CONFIG_FT2232_SPI = no endif CHIP_OBJS = jedec.o stm50flw0x0x.o w39v040c.o w39v080fa.o w29ee011.o \ -- http://www.hailfinger.org/

2 8

[commit] r1048 - trunk
by repository service 14 Jun '10

14 Jun '10

Author: hailfinger Date: Mon Jun 14 20:40:59 2010 New Revision: 1048 URL: http://flashrom.org/trac/coreboot/changeset/1048 Log: Detect incompatible CONFIG_FOO=yes for the specified target and refuse to compile with a meaningful error message. Set the default for incompatible CONFIG_FOO to no. Just running "make" should result in a a build which compiles the common subset of available and working features. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Idwer Vollering <vidwer+lists.flashrom(a)gmail.com> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Jun 14 16:44:08 2010 (r1047) +++ trunk/Makefile Mon Jun 14 20:40:59 2010 (r1048) @@ -53,9 +53,28 @@ CPPFLAGS += -I../libgetopt -I../libpci/include # FIXME Check if we can achieve the same effect with -L../libgetopt -lgetopt LIBS += ../libgetopt/libgetopt.a -# Bus Pirate and Serprog are not supported under DOS. -CONFIG_BUSPIRATE_SPI = no -CONFIG_SERPROG = no +# Bus Pirate and Serprog are not supported under DOS (missing serial support). +ifeq ($(CONFIG_BUSPIRATE_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_BUSPIRATE_SPI=yes +else +override CONFIG_BUSPIRATE_SPI = no +endif +ifeq ($(CONFIG_SERPROG), yes) +UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +else +override CONFIG_SERPROG = no +endif +# Dediprog and FT2232 are not supported under DOS (missing USB support). +ifeq ($(CONFIG_DEDIPROG), yes) +UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes +else +override CONFIG_DEDIPROG = no +endif +ifeq ($(CONFIG_FT2232_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes +else +override CONFIG_FT2232_SPI = no +endif endif CHIP_OBJS = jedec.o stm50flw0x0x.o w39v040c.o w39v080fa.o w29ee011.o \ @@ -279,7 +298,7 @@ strip: $(PROGRAM)$(EXEC_SUFFIX) $(STRIP) $(STRIP_ARGS) $(PROGRAM)$(EXEC_SUFFIX) -compiler: +compiler: featuresavailable @printf "Checking for a C compiler... " @$(shell ( echo "int main(int argc, char **argv)"; \ echo "{ return 0; }"; ) > .test.c ) @@ -318,6 +337,17 @@ .features: features +# If a user does not explicitly request a non-working feature, we should +# silently disable it. However, if a non-working (does not compile) feature +# is explicitly requested, we should bail out with a descriptive error message. +ifeq ($(UNSUPPORTED_FEATURES), ) +featuresavailable: +else +featuresavailable: + @echo "The following features are unavailable on your machine: $(UNSUPPORTED_FEATURES)" + @false +endif + ifeq ($(CONFIG_FT2232_SPI), yes) features: compiler @echo "FEATURES := yes" > .features.tmp @@ -375,6 +405,6 @@ djgpp-dos: clean make CC=i586-pc-msdosdjgpp-gcc STRIP=i586-pc-msdosdjgpp-strip WARNERROR=no OS_ARCH=DOS -.PHONY: all clean distclean compiler pciutils features export tarball dos +.PHONY: all clean distclean compiler pciutils features export tarball dos featuresavailable -include $(OBJS:.o=.d)

1 0

[PATCH] Handle OS where executables have a hardcoded suffix
by Carl-Daniel Hailfinger 14 Jun '10

14 Jun '10

Handle OS where executables have a hardcoded suffix, e.g. DOS with .exe . This ensures that any temp files in the configure/check step of the Makefile are removed correctly. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-dos_exec_suffix/Makefile =================================================================== --- flashrom-dos_exec_suffix/Makefile (Revision 1045) +++ flashrom-dos_exec_suffix/Makefile (Arbeitskopie) @@ -49,6 +49,7 @@ LDFLAGS += -L/usr/local/lib endif ifeq ($(OS_ARCH), DOS) +EXEC_SUFFIX := .exe CPPFLAGS += -I../libgetopt -I../libpci/include # FIXME Check if we can achieve the same effect with -L../libgetopt -lgetopt LIBS += ../libgetopt/libgetopt.a @@ -256,7 +257,7 @@ OBJS = $(CHIP_OBJS) $(CLI_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) $(PROGRAM): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM) $(OBJS) $(FEATURE_LIBS) $(LIBS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) # TAROPTIONS reduces information leakage from the packager's system. # If other tar programs support command line arguments for setting uid/gid of @@ -281,10 +282,10 @@ @printf "Checking for a C compiler... " @$(shell ( echo "int main(int argc, char **argv)"; \ echo "{ return 0; }"; ) > .test.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .test.c -o .test >/dev/null && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .test.c -o .test$(EXEC_SUFFIX) >/dev/null && \ echo "found." || ( echo "not found."; \ - rm -f .test.c .test; exit 1) - @rm -f .test.c .test + rm -f .test.c .test$(EXEC_SUFFIX); exit 1) + @rm -f .test.c .test$(EXEC_SUFFIX) ifeq ($(CHECK_LIBPCI), yes) pciutils: compiler @@ -300,15 +301,15 @@ rm -f .test.c .test.o; exit 1) @printf "Checking if libpci is present and sufficient... " @printf "" > .libdeps - @$(CC) $(LDFLAGS) .test.o -o .test $(LIBS) >/dev/null 2>&1 && \ + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) >/dev/null 2>&1 && \ echo "yes." || ( echo "no."; \ printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test $(LIBS) -lz >/dev/null 2>&1 && \ + $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) -lz >/dev/null 2>&1 && \ ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ echo "Please install libpci (package pciutils) and/or libz."; \ echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test; exit 1) ) - @rm -f .test.c .test.o .test + rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) + @rm -f .test.c .test.o .test$(EXEC_SUFFIX) else pciutils: compiler @printf "" > .libdeps @@ -324,7 +325,7 @@ echo "struct ftdi_context *ftdic = NULL;"; \ echo "int main(int argc, char **argv)"; \ echo "{ return ftdi_init(ftdic); }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ ( echo "found."; echo "FTDISUPPORT := yes" >> .features.tmp ) || \ ( echo "not found."; echo "FTDISUPPORT := no" >> .features.tmp ) @printf "Checking for utsname support... " @@ -332,11 +333,11 @@ echo "struct utsname osinfo;"; \ echo "int main(int argc, char **argv)"; \ echo "{ uname (&osinfo); return 0; }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest + @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) else features: compiler @echo "FEATURES := yes" > .features.tmp @@ -345,11 +346,11 @@ echo "struct utsname osinfo;"; \ echo "int main(int argc, char **argv)"; \ echo "{ uname (&osinfo); return 0; }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest + @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) endif install: $(PROGRAM) -- http://www.hailfinger.org/

2 3

[commit] r1047 - trunk
by repository service 14 Jun '10

14 Jun '10

Author: hailfinger Date: Mon Jun 14 16:44:08 2010 New Revision: 1047 URL: http://flashrom.org/trac/coreboot/changeset/1047 Log: Handle OS where executables have a hardcoded suffix, e.g. DOS with .exe This ensures that any temp files in the configure/check step of the Makefile are removed correctly. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Idwer Vollering <vidwer+flashrom(a)gmail.com> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Jun 14 16:18:37 2010 (r1046) +++ trunk/Makefile Mon Jun 14 16:44:08 2010 (r1047) @@ -49,6 +49,7 @@ LDFLAGS += -L/usr/local/lib endif ifeq ($(OS_ARCH), DOS) +EXEC_SUFFIX := .exe CPPFLAGS += -I../libgetopt -I../libpci/include # FIXME Check if we can achieve the same effect with -L../libgetopt -lgetopt LIBS += ../libgetopt/libgetopt.a @@ -67,7 +68,7 @@ PROGRAMMER_OBJS = udelay.o programmer.o -all: pciutils features $(PROGRAM) +all: pciutils features $(PROGRAM)$(EXEC_SUFFIX) # Set the flashrom version string from the highest revision number # of the checked out flashrom files. @@ -255,8 +256,8 @@ OBJS = $(CHIP_OBJS) $(CLI_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) -$(PROGRAM): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM) $(OBJS) $(FEATURE_LIBS) $(LIBS) +$(PROGRAM)$(EXEC_SUFFIX): $(OBJS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) # TAROPTIONS reduces information leakage from the packager's system. # If other tar programs support command line arguments for setting uid/gid of @@ -268,23 +269,24 @@ # Make sure to add all names of generated binaries here. # This includes all frontends and libflashrom. +# We don't use EXEC_SUFFIX here because we want to clean everything. clean: rm -f $(PROGRAM) $(PROGRAM).exe *.o *.d distclean: clean rm -f .features .libdeps -strip: $(PROGRAM) - $(STRIP) $(STRIP_ARGS) $(PROGRAM) +strip: $(PROGRAM)$(EXEC_SUFFIX) + $(STRIP) $(STRIP_ARGS) $(PROGRAM)$(EXEC_SUFFIX) compiler: @printf "Checking for a C compiler... " @$(shell ( echo "int main(int argc, char **argv)"; \ echo "{ return 0; }"; ) > .test.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .test.c -o .test >/dev/null && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .test.c -o .test$(EXEC_SUFFIX) >/dev/null && \ echo "found." || ( echo "not found."; \ - rm -f .test.c .test; exit 1) - @rm -f .test.c .test + rm -f .test.c .test$(EXEC_SUFFIX); exit 1) + @rm -f .test.c .test$(EXEC_SUFFIX) ifeq ($(CHECK_LIBPCI), yes) pciutils: compiler @@ -300,15 +302,15 @@ rm -f .test.c .test.o; exit 1) @printf "Checking if libpci is present and sufficient... " @printf "" > .libdeps - @$(CC) $(LDFLAGS) .test.o -o .test $(LIBS) >/dev/null 2>&1 && \ + @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) >/dev/null 2>&1 && \ echo "yes." || ( echo "no."; \ printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test $(LIBS) -lz >/dev/null 2>&1 && \ + $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) -lz >/dev/null 2>&1 && \ ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ echo "Please install libpci (package pciutils) and/or libz."; \ echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test; exit 1) ) - @rm -f .test.c .test.o .test + rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) + @rm -f .test.c .test.o .test$(EXEC_SUFFIX) else pciutils: compiler @printf "" > .libdeps @@ -324,7 +326,7 @@ echo "struct ftdi_context *ftdic = NULL;"; \ echo "int main(int argc, char **argv)"; \ echo "{ return ftdi_init(ftdic); }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ ( echo "found."; echo "FTDISUPPORT := yes" >> .features.tmp ) || \ ( echo "not found."; echo "FTDISUPPORT := no" >> .features.tmp ) @printf "Checking for utsname support... " @@ -332,11 +334,11 @@ echo "struct utsname osinfo;"; \ echo "int main(int argc, char **argv)"; \ echo "{ uname (&osinfo); return 0; }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest + @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) else features: compiler @echo "FEATURES := yes" > .features.tmp @@ -345,17 +347,17 @@ echo "struct utsname osinfo;"; \ echo "int main(int argc, char **argv)"; \ echo "{ uname (&osinfo); return 0; }"; ) > .featuretest.c ) - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest >/dev/null 2>&1 && \ + @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest + @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) endif -install: $(PROGRAM) +install: $(PROGRAM)$(EXEC_SUFFIX) mkdir -p $(DESTDIR)$(PREFIX)/sbin mkdir -p $(DESTDIR)$(MANDIR)/man8 - $(INSTALL) -m 0755 $(PROGRAM) $(DESTDIR)$(PREFIX)/sbin + $(INSTALL) -m 0755 $(PROGRAM)$(EXEC_SUFFIX) $(DESTDIR)$(PREFIX)/sbin $(INSTALL) -m 0644 $(PROGRAM).8 $(DESTDIR)$(MANDIR)/man8 export:

1 0

[PATCH] Add comments to nicrealtek
by Carl-Daniel Hailfinger 14 Jun '10

14 Jun '10

I just read nicrealtek and realized that the code uses magic constants, but they are not explained. That's OK if you know the datasheet well, but for casual readers some comments are really helpful. I'm not sure whether we want to disable hardware flash access forever without enabling it again on shutdown. A few other places made me wonder as well. I've added FIXME comments in those places. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-nicrealtek_comments/nicrealtek.c =================================================================== --- flashrom-nicrealtek_comments/nicrealtek.c (Revision 1028) +++ flashrom-nicrealtek_comments/nicrealtek.c (Arbeitskopie) @@ -65,6 +65,7 @@ int nicrealtek_shutdown(void) { + /* FIXME: We forgot to disable software access again. */ free(programmer_param); pci_cleanup(pacc); release_io_perms(); @@ -73,8 +74,14 @@ void nicrealtek_chip_writeb(uint8_t val, chipaddr addr) { + /* Output addr and data, set WE to 0, set OE to 1, set CS to 0, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x0A0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); + /* Output addr and data, set WE to 1, set OE to 1, set CS to 1, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x1E0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); } @@ -83,11 +90,20 @@ { uint8_t val; + /* FIXME: Can we skip reading the old data and simply use 0? */ + /* Read old data. */ val = INB(io_base_addr + BIOS_ROM_DATA); + /* Output new addr and old data, set WE to 1, set OE to 0, set CS to 0, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x060000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); + /* Read new data. */ val = INB(io_base_addr + BIOS_ROM_DATA); + /* Output addr and new data, set WE to 1, set OE to 1, set CS to 1, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x1E0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); -- http://www.hailfinger.org/

2 2

[commit] r1046 - trunk
by repository service 14 Jun '10

14 Jun '10

Author: hailfinger Date: Mon Jun 14 16:18:37 2010 New Revision: 1046 URL: http://flashrom.org/trac/coreboot/changeset/1046 Log: The nicrealtek code uses magic constants, but they are not explained. That's OK if you know the datasheet well, but for casual readers some comments are really helpful. I'm not sure whether we want to disable hardware flash access forever without enabling it again on shutdown. A few other places made me wonder as well. I've added FIXME comments in those places. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Andrew Morgan <ziltro(a)ziltro.com> Modified: trunk/nicrealtek.c Modified: trunk/nicrealtek.c ============================================================================== --- trunk/nicrealtek.c Mon Jun 14 14:58:06 2010 (r1045) +++ trunk/nicrealtek.c Mon Jun 14 16:18:37 2010 (r1046) @@ -65,6 +65,7 @@ int nicrealtek_shutdown(void) { + /* FIXME: We forgot to disable software access again. */ free(programmer_param); pci_cleanup(pacc); release_io_perms(); @@ -73,8 +74,14 @@ void nicrealtek_chip_writeb(uint8_t val, chipaddr addr) { + /* Output addr and data, set WE to 0, set OE to 1, set CS to 0, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x0A0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); + /* Output addr and data, set WE to 1, set OE to 1, set CS to 1, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x1E0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); } @@ -83,11 +90,20 @@ { uint8_t val; + /* FIXME: Can we skip reading the old data and simply use 0? */ + /* Read old data. */ val = INB(io_base_addr + BIOS_ROM_DATA); + /* Output new addr and old data, set WE to 1, set OE to 0, set CS to 0, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x060000 | (val << 24), io_base_addr + BIOS_ROM_ADDR); + /* Read new data. */ val = INB(io_base_addr + BIOS_ROM_DATA); + /* Output addr and new data, set WE to 1, set OE to 1, set CS to 1, + * enable software access. + */ OUTL(((uint32_t)addr & 0x01FFFF) | 0x1E0000 | (val << 24), io_base_addr + BIOS_ROM_ADDR);

1 0

[PATCH] SST25LF040A support
by Carl-Daniel Hailfinger 14 Jun '10

14 Jun '10

SST25LF040A support patch from Stefan Reinauer. Stefan tested probing. I changed the coding style a bit to conform to flashrom rules. I checked against datasheets, should work. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-stefan_sst25lf040a/flashchips.c =================================================================== --- flashrom-stefan_sst25lf040a/flashchips.c (Revision 1026) +++ flashrom-stefan_sst25lf040a/flashchips.c (Arbeitskopie) @@ -3817,6 +3817,34 @@ { .vendor = "SST", + .name = "SST25LF040A.RES", + .bustype = CHIP_BUSTYPE_SPI, + .manufacture_id = SST_ID, + .model_id = SST_25VF040_REMS, + .total_size = 512, + .page_size = 256, + .tested = TEST_OK_PROBE, + .probe = probe_spi_res2, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, + }, + .write = spi_chip_write_1, + .read = spi_chip_read, + }, + + { + .vendor = "SST", .name = "SST25VF040B.REMS", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = SST_ID, Index: flashrom-stefan_sst25lf040a/flashchips.h =================================================================== --- flashrom-stefan_sst25lf040a/flashchips.h (Revision 1026) +++ flashrom-stefan_sst25lf040a/flashchips.h (Arbeitskopie) @@ -387,7 +387,7 @@ #define SST_25VF512A_REMS 0x48 /* REMS or RES opcode */ #define SST_25VF010_REMS 0x49 /* REMS or RES opcode */ #define SST_25VF020_REMS 0x43 /* REMS or RES opcode */ -#define SST_25VF040_REMS 0x44 /* REMS or RES opcode */ +#define SST_25VF040_REMS 0x44 /* REMS or RES opcode, same as SST25LF040A */ #define SST_25VF040B 0x258D #define SST_25VF040B_REMS 0x8D /* REMS or RES opcode */ #define SST_25VF080_REMS 0x80 /* REMS or RES opcode */ -- http://www.hailfinger.org/

2 4

[commit] r1045 - trunk
by repository service 14 Jun '10

14 Jun '10

Author: hailfinger Date: Mon Jun 14 14:58:06 2010 New Revision: 1045 URL: http://flashrom.org/trac/coreboot/changeset/1045 Log: Add SST25LF040A support. Checked against datasheets, should work. Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/flashchips.c trunk/flashchips.h Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Mon Jun 14 14:42:05 2010 (r1044) +++ trunk/flashchips.c Mon Jun 14 14:58:06 2010 (r1045) @@ -3840,6 +3840,34 @@ { .vendor = "SST", + .name = "SST25LF040A.RES", + .bustype = CHIP_BUSTYPE_SPI, + .manufacture_id = SST_ID, + .model_id = SST_25VF040_REMS, + .total_size = 512, + .page_size = 256, + .tested = TEST_OK_PROBE, + .probe = probe_spi_res2, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, + }, + .write = spi_chip_write_1, + .read = spi_chip_read, + }, + + { + .vendor = "SST", .name = "SST25VF040B.REMS", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = SST_ID, Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Mon Jun 14 14:42:05 2010 (r1044) +++ trunk/flashchips.h Mon Jun 14 14:58:06 2010 (r1045) @@ -388,7 +388,7 @@ #define SST_25VF512A_REMS 0x48 /* REMS or RES opcode */ #define SST_25VF010_REMS 0x49 /* REMS or RES opcode */ #define SST_25VF020_REMS 0x43 /* REMS or RES opcode */ -#define SST_25VF040_REMS 0x44 /* REMS or RES opcode */ +#define SST_25VF040_REMS 0x44 /* REMS or RES opcode, same as SST25LF040A */ #define SST_25VF040B 0x258D #define SST_25VF040B_REMS 0x8D /* REMS or RES opcode */ #define SST_25VF080_REMS 0x80 /* REMS or RES opcode */

1 0

[PATCH] Makefile cleanup
by Carl-Daniel Hailfinger 14 Jun '10

14 Jun '10

We already have NEED_PCI in the Makefile to link in PCI support. Add NEED_SERIAL and NEED_NET to decouple individual drivers from compilation and linking decisions. Move libgetopt from a DOS+PCI dependency to a DOS dependency to fix linking on DOS if no driver requiring PCI is enabled. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-makefile_cleanup/Makefile =================================================================== --- flashrom-makefile_cleanup/Makefile (Revision 1039) +++ flashrom-makefile_cleanup/Makefile (Arbeitskopie) @@ -50,6 +50,8 @@ endif ifeq ($(OS_ARCH), DOS) CPPFLAGS += -I../libgetopt -I../libpci/include +# FIXME Check if we can achieve the same effect with -L../libgetopt -lgetopt +LIBS += ../libgetopt/libgetopt.a # Bus Pirate and Serprog are not supported under DOS. CONFIG_BUSPIRATE_SPI = no CONFIG_SERPROG = no @@ -136,10 +138,9 @@ ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o -ifeq ($(OS_ARCH), SunOS) -LIBS += -lsocket +NEED_SERIAL := yes +NEED_NET := yes endif -endif ifeq ($(CONFIG_BITBANG_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BITBANG_SPI=1' @@ -204,6 +205,7 @@ ifeq ($(CONFIG_BUSPIRATE_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BUSPIRATE_SPI=1' PROGRAMMER_OBJS += buspirate_spi.o +NEED_SERIAL := yes endif ifeq ($(CONFIG_DEDIPROG), yes) @@ -212,20 +214,18 @@ PROGRAMMER_OBJS += dediprog.o endif -# Ugly, but there's no elif/elseif. -ifeq ($(CONFIG_SERPROG), yes) +ifeq ($(NEED_SERIAL), yes) LIB_OBJS += serial.o -else -ifeq ($(CONFIG_BUSPIRATE_SPI), yes) -LIB_OBJS += serial.o endif + +ifeq ($(NEED_NET), yes) +ifeq ($(OS_ARCH), SunOS) +LIBS += -lsocket endif +endif ifeq ($(NEED_PCI), yes) CHECK_LIBPCI = yes -endif - -ifeq ($(NEED_PCI), yes) FEATURE_CFLAGS += -D'NEED_PCI=1' PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(OS_ARCH), NetBSD) @@ -236,7 +236,7 @@ else ifeq ($(OS_ARCH), DOS) # FIXME There needs to be a better way to do this -LIBS += ../libpci/lib/libpci.a ../libgetopt/libgetopt.a +LIBS += ../libpci/lib/libpci.a else LIBS += -lpci endif -- http://www.hailfinger.org/

2 2

[commit] r1044 - trunk
by repository service 14 Jun '10

14 Jun '10

Author: hailfinger Date: Mon Jun 14 14:42:05 2010 New Revision: 1044 URL: http://flashrom.org/trac/coreboot/changeset/1044 Log: We already have NEED_PCI in the Makefile to link in PCI support. Add NEED_SERIAL and NEED_NET to decouple individual drivers from compilation and linking decisions. Move libgetopt from a DOS+PCI dependency to a DOS dependency to fix linking on DOS if no driver requiring PCI is enabled. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Sun Jun 13 12:16:12 2010 (r1043) +++ trunk/Makefile Mon Jun 14 14:42:05 2010 (r1044) @@ -50,6 +50,8 @@ endif ifeq ($(OS_ARCH), DOS) CPPFLAGS += -I../libgetopt -I../libpci/include +# FIXME Check if we can achieve the same effect with -L../libgetopt -lgetopt +LIBS += ../libgetopt/libgetopt.a # Bus Pirate and Serprog are not supported under DOS. CONFIG_BUSPIRATE_SPI = no CONFIG_SERPROG = no @@ -136,9 +138,8 @@ ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o -ifeq ($(OS_ARCH), SunOS) -LIBS += -lsocket -endif +NEED_SERIAL := yes +NEED_NET := yes endif ifeq ($(CONFIG_BITBANG_SPI), yes) @@ -204,6 +205,7 @@ ifeq ($(CONFIG_BUSPIRATE_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BUSPIRATE_SPI=1' PROGRAMMER_OBJS += buspirate_spi.o +NEED_SERIAL := yes endif ifeq ($(CONFIG_DEDIPROG), yes) @@ -212,20 +214,18 @@ PROGRAMMER_OBJS += dediprog.o endif -# Ugly, but there's no elif/elseif. -ifeq ($(CONFIG_SERPROG), yes) -LIB_OBJS += serial.o -else -ifeq ($(CONFIG_BUSPIRATE_SPI), yes) +ifeq ($(NEED_SERIAL), yes) LIB_OBJS += serial.o endif -endif -ifeq ($(NEED_PCI), yes) -CHECK_LIBPCI = yes +ifeq ($(NEED_NET), yes) +ifeq ($(OS_ARCH), SunOS) +LIBS += -lsocket +endif endif ifeq ($(NEED_PCI), yes) +CHECK_LIBPCI = yes FEATURE_CFLAGS += -D'NEED_PCI=1' PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(OS_ARCH), NetBSD) @@ -236,7 +236,7 @@ else ifeq ($(OS_ARCH), DOS) # FIXME There needs to be a better way to do this -LIBS += ../libpci/lib/libpci.a ../libgetopt/libgetopt.a +LIBS += ../libpci/lib/libpci.a else LIBS += -lpci endif

1 0

Probe results for Powerspec 8731
by Steven Zakulec 14 Jun '10

14 Jun '10

Hi, here's the results of flashrom, lspci, and superio as indicated on the wiki for a Powerspec 8731 machine. Here's a link to the machine specs: http://www.powerspec.com/systems/archives/system_archive.phtml?selection=87… and here's the link to the motherboard maker: http://www.fic.com.tw/support/motherboard/motherboard.aspx?model_id=120 The company's site has no BIOS updates, but the website here: http://www.updrivers.com/getbios/Motherboard/FIC/VI35L-BIOS/9265.html seems to have a BIOS update.

1 0

# flashrom -V
by Julian Hughes 14 Jun '10

14 Jun '10

# flashrom -V flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "Acer" DMI string system-product-name: "Aspire X3200" DMI string system-version: "R01-A2" DMI string baseboard-manufacturer: "Acer" DMI string baseboard-product-name: "WMCP78M" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8718 Found chipset "NVIDIA MCP78S", enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Guessed flash bus type is SPI Found SMBus device 10de:0752 at 00:01:1 SPI BAR is at 0xfdf80000, after clearing low bits BAR is at 0xfdf80000 Mapping MCP67 SPI at 0xfdf80000, unaligned size 0x544. SPI control is 0xc01a, enable=0, idle=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org to help us finish support for your chipset. Thanks. SPI on this chipset is not supported yet. OK. This chipset supports the following protocols: None. Calibrating delay loop... 605M loops per second, 100 myus = 232 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 28F004S5, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Intel 82802AC, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Macronix MX25L512, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for PMC Pm49FL004, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF003A/B, 384 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF004A/B, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF004C, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF008A, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF008C, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF016C, 2048 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for SST SST49LF020, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW040B, 512 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW080A, 1024 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FLW080B, 1024 KB: skipped. Host bus type None and chip bus type LPC,FWH are incompatible. Probing for ST M50FW002, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW016, 2048 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW040, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50FW080, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for ST M50LPW116, 2048 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W49F002U, 256 KB: skipped. Host bus type None and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type None and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080FA, 1024 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Host bus type None and chip bus type FWH are incompatible. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type None and chip bus type SPI are incompatible. No EEPROM/flash device found. If you know which flash chip you have, and if this version of flashrom supports a similar flash chip, you can try to force read your chip. Run: flashrom -f -r -c similar_supported_flash_chip filename Note: flashrom can never write when the flash chip isn't found automatically.

1 0

Re: [flashrom] [PATCH] Board-enable for MS-7025 (K8N Neo2 Platinum)
by rider 13 Jun '10

13 Jun '10

So, it works like a charm. I would like to thank Michael once again, it was truly amazing expirience. Cheers, Valentine "Pegasus rider" Yatsenko.

3 2

[commit] r1043 - trunk
by repository service 13 Jun '10

13 Jun '10

Author: mkarcher Date: Sun Jun 13 12:16:12 2010 New Revision: 1043 URL: http://flashrom.org/trac/coreboot/changeset/1043 Log: VIA: disable byte merging All mentioned north bridges have been checked against data sheet. That's all north bridges google found a datasheet for with "byte merge" included. Runs multiple chipset enables if the first one requests further enables to be run. VIA byte-merging logic tested: works. multiple chipset logic: completely untested Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/chipset_enable.c Modified: trunk/chipset_enable.c ============================================================================== --- trunk/chipset_enable.c Sun Jun 13 01:14:03 2010 (r1042) +++ trunk/chipset_enable.c Sun Jun 13 12:16:12 2010 (r1043) @@ -37,6 +37,8 @@ #if defined(__i386__) || defined(__x86_64__) +#define NOT_DONE_YET 1 + static int enable_flash_ali_m1533(struct pci_dev *dev, const char *name) { uint8_t tmp; @@ -642,6 +644,32 @@ return enable_flash_ich_dc_spi(dev, name, 10); } +static void via_do_byte_merge(void * arg) +{ + struct pci_dev * dev = arg; + uint8_t val; + + msg_pdbg("Re-enabling byte merging\n"); + val = pci_read_byte(dev, 0x71); + val |= 0x40; + pci_write_byte(dev, 0x71, val); +} + +static int via_no_byte_merge(struct pci_dev *dev, const char *name) +{ + uint8_t val; + + val = pci_read_byte(dev, 0x71); + if (val & 0x40) + { + msg_pdbg("Disabling byte merging\n"); + val &= ~0x40; + pci_write_byte(dev, 0x71, val); + register_shutdown(via_do_byte_merge, dev); + } + return NOT_DONE_YET; /* need to find south bridge, too */ +} + static int enable_flash_vt823x(struct pci_dev *dev, const char *name) { uint8_t val; @@ -1420,6 +1448,14 @@ {0x1039, 0x0746, NT, "SiS", "746", enable_flash_sis540}, {0x1039, 0x0748, NT, "SiS", "748", enable_flash_sis540}, {0x1039, 0x0755, NT, "SiS", "755", enable_flash_sis540}, + /* VIA northbridges */ + {0x1106, 0x0585, NT, "VIA", "VT82C585VPX", via_no_byte_merge}, + {0x1106, 0x0595, NT, "VIA", "VT82C595", via_no_byte_merge}, + {0x1106, 0x0597, NT, "VIA", "VT82C597", via_no_byte_merge}, + {0x1106, 0x0691, NT, "VIA", "VT82C69x", via_no_byte_merge}, /* 691, 693a, 694t, 694x checked */ + {0x1106, 0x0601, NT, "VIA", "VT8601/VT8601A", via_no_byte_merge}, + {0x1106, 0x8601, NT, "VIA", "VT8601T", via_no_byte_merge}, + /* VIA southbridges */ {0x1106, 0x8324, OK, "VIA", "CX700", enable_flash_vt823x}, {0x1106, 0x8231, NT, "VIA", "VT8231", enable_flash_vt823x}, {0x1106, 0x3074, NT, "VIA", "VT8233", enable_flash_vt823x}, @@ -1446,11 +1482,16 @@ for (i = 0; chipset_enables[i].vendor_name != NULL; i++) { dev = pci_dev_find(chipset_enables[i].vendor_id, chipset_enables[i].device_id); - if (dev) - break; - } - - if (dev) { + if (!dev) + continue; + if (ret != -2) { + msg_pinfo("WARNING: unexpected second chipset match: " + "\"%s %s\"\nignoring, please report lspci and " + "board URL to flashrom(a)flashrom.org!\n", + chipset_enables[i].vendor_name, + chipset_enables[i].device_name); + continue; + } msg_pinfo("Found chipset \"%s %s\", enabling flash write... ", chipset_enables[i].vendor_name, chipset_enables[i].device_name); @@ -1460,11 +1501,15 @@ ret = chipset_enables[i].doit(dev, chipset_enables[i].device_name); - if (ret) + if (ret == NOT_DONE_YET) { + ret = -2; + msg_pinfo("OK - searching further chips.\n"); + } else if (ret < 0) msg_pinfo("FAILED!\n"); - else + else if(ret == 0) msg_pinfo("OK.\n"); } + msg_pinfo("This chipset supports the following protocols: %s.\n", flashbuses_to_text(buses_supported));

1 0

Re: [flashrom] [PATCH] VIA: disable byte merging
by Carl-Daniel Hailfinger 13 Jun '10

13 Jun '10

[updated to apply to latest svn] All mentioned north bridges have been checked against data sheet. That's all north bridges google found a datasheet for with "byte enable" included. Second revision. Should now run multiple chipset enables if the first one requests further enables to be run. VIA byte-merging logic tested: works. multiple chipset logic: completely untested Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Index: flashrom-via_no_byte_merge/chipset_enable.c =================================================================== --- flashrom-via_no_byte_merge/chipset_enable.c (Revision 998) +++ flashrom-via_no_byte_merge/chipset_enable.c (Arbeitskopie) @@ -34,6 +34,8 @@ #include <fcntl.h> #include "flash.h" +#define NOT_DONE_YET 1 + extern int ichspi_lock; static int enable_flash_ali_m1533(struct pci_dev *dev, const char *name) @@ -639,6 +641,32 @@ return enable_flash_ich_dc_spi(dev, name, 10); } +static void via_do_byte_merge(void * arg) +{ + struct pci_dev * dev = arg; + uint8_t val; + + msg_pdbg("Re-enabling byte merging\n"); + val = pci_read_byte(dev, 0x71); + val |= 0x40; + pci_write_byte(dev, 0x71, val); +} + +static int via_no_byte_merge(struct pci_dev *dev, const char *name) +{ + uint8_t val; + + val = pci_read_byte(dev, 0x71); + if (val & 0x40) + { + msg_pdbg("Disabling byte merging\n"); + val &= ~0x40; + pci_write_byte(dev, 0x71, val); + register_shutdown(via_do_byte_merge, dev); + } + return NOT_DONE_YET; /* need to find south bridge, too */ +} + static int enable_flash_vt823x(struct pci_dev *dev, const char *name) { uint8_t val; @@ -1405,6 +1433,14 @@ {0x1039, 0x0746, NT, "SiS", "746", enable_flash_sis540}, {0x1039, 0x0748, NT, "SiS", "748", enable_flash_sis540}, {0x1039, 0x0755, NT, "SiS", "755", enable_flash_sis540}, + /* VIA northbridges */ + {0x1106, 0x0585, NT, "VIA", "VT82C585VPX", via_no_byte_merge}, + {0x1106, 0x0595, NT, "VIA", "VT82C595", via_no_byte_merge}, + {0x1106, 0x0597, NT, "VIA", "VT82C597", via_no_byte_merge}, + {0x1106, 0x0691, NT, "VIA", "VT82C69x", via_no_byte_merge}, /* 691, 693a, 694t, 694x checked */ + {0x1106, 0x0601, NT, "VIA", "VT8601/VT8601A", via_no_byte_merge}, + {0x1106, 0x8601, NT, "VIA", "VT8601T", via_no_byte_merge}, + /* VIA southbridges */ {0x1106, 0x8324, OK, "VIA", "CX700", enable_flash_vt823x}, {0x1106, 0x8231, NT, "VIA", "VT8231", enable_flash_vt823x}, {0x1106, 0x3074, NT, "VIA", "VT8233", enable_flash_vt823x}, @@ -1431,22 +1467,31 @@ for (i = 0; chipset_enables[i].vendor_name != NULL; i++) { dev = pci_dev_find(chipset_enables[i].vendor_id, chipset_enables[i].device_id); - if (dev) - break; - } - - if (dev) { + if (!dev) + continue; + if (ret != -2) { + msg_pinfo("WARNING: unexpected second chipset match: " + "\"%s %s\"\nignoring, please report lspci and " + "board URL to flashrom(a)flashrom.org!\n", + chipset_enables[i].vendor_name, + chipset_enables[i].device_name); + continue; + } msg_pinfo("Found chipset \"%s %s\", enabling flash write... ", chipset_enables[i].vendor_name, chipset_enables[i].device_name); ret = chipset_enables[i].doit(dev, chipset_enables[i].device_name); - if (ret) + if (ret == NOT_DONE_YET) { + ret = -2; + msg_pinfo("OK - searching further chips.\n"); + } else if (ret < 0) msg_pinfo("FAILED!\n"); - else + else if(ret == 0) msg_pinfo("OK.\n"); } + msg_pinfo("This chipset supports the following protocols: %s.\n", flashbuses_to_text(buses_supported)); -- http://www.hailfinger.org/

2 2

Motherboard report: Abit NF-M2 nView
by Michael 13 Jun '10

13 Jun '10

My Abit NF-M2 nView (NVIDIA 6150/NF430) motherboard doesn't appear to be supported by flashrom yet (it recognizes the chip and chipset, but it seems that write enable is not set). The official BIOS downloads for this board are here: http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NA… AM2&pPRODINFO=BIOS I've tried writing the .bin files from the BIOS archives on that page and all of them fail to verify. Here's the output of 'flashrom -V', 'lspci -nnvvvxxx', and 'superiotool -deV': Script started on Fri 09 Apr 2010 11:56:24 AM EDT # flashrom -V Calibrating delay loop... 527M loops per second. OK. No coreboot table found. Found chipset "NVIDIA MCP51", enabling flash write... OK. Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for ASD AE49F2008, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N), 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Atmel AT25DF321, 4096 KB: spi_command called, but no SPI chipset detected Probing for AMIC Technology A25L40P, 512 KB: spi_command called, but no SPI chipset detected Probing for AMIC Technology A49LF040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for AMIC Technology A29040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for EMST F49B002UA, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L4005, 512 KB: spi_command called, but no SPI chipset detected Probing for Macronix MX25L8005, 1024 KB: spi_command called, but no SPI chipset detected Probing for Macronix MX25L1605, 2048 KB: spi_command called, but no SPI chipset detected Probing for Macronix MX25L3205, 4096 KB: spi_command called, but no SPI chipset detected Probing for Macronix MX29F002, 256 KB: probe_29f002: id1 0x9d, id2 0x6e Probing for PMC Pm25LV010, 128 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm25LV016B, 2048 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm25LV020, 256 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm25LV040, 512 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm25LV080B, 1024 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm25LV512, 64 KB: spi_command called, but no SPI chipset detected Probing for PMC Pm49FL002, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for PMC Pm49FL004, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Found chip "PMC Pm49FL004" (512 KB) at physical address 0xfff80000. Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0xff, id2 0xff Probing for Spansion S25FL016A, 2048 KB: spi_command called, but no SPI chipset detected Probing for SST SST25VF016B, 2048 KB: spi_command called, but no SPI chipset detected Probing for SST SST25VF040B, 512 KB: spi_command called, but no SPI chipset detected Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0x49, id2 0x4d Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST29EE020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF002A/B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF003A/B, 384 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF004A/B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x49, id2 0x4d Probing for SST SST49LF008A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SST SST49LF080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: spi_command called, but no SPI chipset detected Probing for ST M25P10-A, 128 KB: spi_command called, but no SPI chipset detected Probing for ST M25P20, 256 KB: spi_command called, but no SPI chipset detected Probing for ST M25P40, 512 KB: spi_command called, but no SPI chipset detected Probing for ST M25P40-old, 512 KB: spi_command called, but no SPI chipset detected Probing for ST M25P80, 1024 KB: spi_command called, but no SPI chipset detected Probing for ST M25P16, 2048 KB: spi_command called, but no SPI chipset detected Probing for ST M25P32, 4096 KB: spi_command called, but no SPI chipset detected Probing for ST M25P64, 8192 KB: spi_command called, but no SPI chipset detected Probing for ST M25P128, 16384 KB: spi_command called, but no SPI chipset detected Probing for ST M29F002B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for ST M29F002T/NT, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0x49, id2 0x4d Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x49, id2 0x44 Probing for ST M29W010B, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for ST M29W040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0x9d, id2 0x6e Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0x9d, id2 0x6e Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x49, id2 0x4d Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation Probing for SyncMOS S29C31004T, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51001T, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51002T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for SyncMOS S29C51004T, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W25x10, 128 KB: spi_command called, but no SPI chipset detected Probing for Winbond W25x20, 256 KB: spi_command called, but no SPI chipset detected Probing for Winbond W25x40, 512 KB: spi_command called, but no SPI chipset detected Probing for Winbond W25x80, 1024 KB: spi_command called, but no SPI chipset detected Probing for Winbond W29C011, 128 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W29EE011, 128 KB: === Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. === Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation Probing for Winbond W49F002U, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W49V002FA, 256 KB: probe_jedec: id1 0x9d, id2 0x6e Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: vid 0xff, did 0xff Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: vid 0x9d, did 0x6e Probing for EON unknown EON SPI chip, 0 KB: spi_command called, but no SPI chipset detected Probing for Macronix unknown Macronix SPI chip, 0 KB: spi_command called, but no SPI chipset detected Probing for PMC unknown PMC SPI chip, 0 KB: spi_command called, but no SPI chipset detected Probing for SST unknown SST SPI chip, 0 KB: spi_command called, but no SPI chipset detected Probing for ST unknown ST SPI chip, 0 KB: spi_command called, but no SPI chipset detected No operations were specified. # lspci -nnvvvxxx 00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f0] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b- Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 800MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 f0 02 06 00 b0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00 40: 7b 14 26 1c 08 e0 e0 01 22 00 11 11 22 30 11 00 50: 23 06 7f 80 03 05 7f 80 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 05 00 70: 44 44 41 00 d0 09 00 00 11 00 00 00 11 11 88 00 80: 23 99 88 00 1f 00 64 0c 03 00 00 00 7f 00 00 00 90: 78 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 61 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 08 00 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 10 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0 [10de:02fa] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx- 00: de 10 fa 02 00 01 20 40 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 10 00 21 21 14 00 11 11 00 00 03 00 00 00 60: 21 88 13 02 de 8f e1 1f 08 72 4e 10 02 3f 00 20 70: 10 32 54 0a 10 00 00 00 a0 00 00 00 20 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 50 3f 90 3f 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 01 00 00 00 80 f9 fd 00 e0: 00 00 c9 fe 00 00 00 00 00 fc ff ff 00 00 00 00 f0: 00 00 00 00 c7 02 32 00 00 00 00 00 00 00 00 00 00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1 [10de:02fe] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 fe 02 00 00 20 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 7b 14 26 1c 9b a0 1c 60 9b a0 c0 21 00 00 00 00 50: 00 00 00 00 00 00 00 00 7b 01 d1 f2 02 1f 1c 80 60: 02 1f 1c 00 00 00 00 00 02 10 1c a0 02 0c 1c 90 70: 02 10 1c 90 02 14 1c 90 02 0c 1c 80 02 10 1c 80 80: 02 14 1c 80 02 18 1c 80 02 1c 1c 80 01 10 1c 80 90: 02 14 1c 80 11 00 11 00 32 01 00 00 00 00 00 00 a0: c2 00 40 01 10 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 41 23 05 08 c0: fd ff ff ff ff ff ff ff 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5 [10de:02f8] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 f8 02 00 00 a0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 7b 14 26 1c 00 00 00 00 02 10 1c 80 02 10 1c a0 50: 02 0c 1c 90 02 10 1c 90 02 14 1c 90 02 0c 1c 80 60: 02 10 1c 80 02 14 1c 80 02 18 1c 80 02 1c 1c 80 70: 01 10 1c 80 1f 20 c0 81 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 08 02 1f 1c 80 70 20 00 00 90: 89 da 01 09 00 00 00 00 11 00 10 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 08 00 00 00 d2 18 00 00 10 00 02 00 00 00 00 00 c0: 00 80 00 00 00 00 00 00 0f 01 00 05 00 00 00 00 d0: 00 00 f0 03 00 04 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 60 ea 10 10 18 00 00 20 00 00 00 00 00 00 00 00 00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4 [10de:02f9] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: de 10 f9 02 06 00 a0 00 a2 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: ef dd 7b 2f f7 de 7b 2f f7 de 7b 2f f7 02 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 70: 0a 00 00 00 03 00 00 00 25 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 05 00 00 00 04 00 00 00 90: 03 04 00 00 01 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: ff 7f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] #00 [00fe] Capabilities: [fc] #00 [0000] 00: de 10 ff 02 06 00 b0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00 40: 17 00 00 00 00 fe fe 00 00 fe fe 00 00 fe fe 00 50: 00 fe fe 00 00 fe fe 00 00 fe fe 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3 [10de:027f] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 7f 02 00 01 20 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 08 00 00 00 00 00 00 00 00 80 cb fe 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2 [10de:027e] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 7e 02 00 00 20 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 7b 14 26 1c 11 00 00 00 64 06 00 00 11 00 00 00 50: 64 05 00 00 60 00 40 00 60 70 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 04 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 04 b0: ff ff 03 00 10 11 00 00 ac 10 20 00 30 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:05.0 VGA compatible controller [0300]: nVidia Corporation C51PV [GeForce 6150] [10de:0240] (rev a2) (prog-if 00 [VGA controller]) Subsystem: nVidia Corporation Device [10de:0222] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 5 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 88000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: nvidia Kernel modules: nvidiafb, nvidia 00: de 10 40 02 07 00 b0 00 a2 00 00 03 00 00 00 00 10: 00 00 00 fc 0c 00 00 e0 00 00 00 00 04 00 00 fb 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 22 02 30: 00 00 00 00 48 00 00 00 00 00 00 00 05 01 00 00 40: de 10 22 02 00 00 00 00 01 50 02 00 00 00 00 00 50: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 00 00 00 04 00 00 00 00 00 00 00 01 00 00 00 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff a0: 00 00 f8 00 00 00 00 04 00 00 00 00 ff ff ff ff b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b- Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 800MHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 70 02 06 00 b0 00 a2 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00 40: 7b 14 26 1c 08 e0 e9 01 22 30 00 00 d0 00 00 00 50: 23 05 7f 80 03 00 00 00 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 05 00 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 55 00 80: 23 55 55 00 fa 00 64 0c 03 00 00 00 7f 00 00 00 90: 78 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 80 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 08 00 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: de 10 60 02 0f 00 a0 00 a2 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: 7b 14 26 1c 00 f0 ff fe fa 3e ff 00 fa 3e ff 00 50: fa 3e ff 00 00 5a 62 02 00 00 00 01 00 00 ff ff 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 f9 ff 70: 10 00 ff ff c5 00 00 00 00 00 04 19 00 b0 00 05 80: 09 a0 00 ba 05 ba 00 00 c0 00 00 01 00 00 00 00 90: 00 00 00 00 00 00 00 00 21 47 65 b7 ef cd 00 00 a0: 00 00 10 80 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 95 02 97 02 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at 1c00 [size=64] Region 5: I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00: de 10 64 02 01 00 b0 00 a2 00 05 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 1c 00 00 41 1c 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 00 00 40: 7b 14 26 1c 01 00 02 c0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 10 00 00 01 14 00 00 01 18 00 00 00 00 00 00 70: 01 00 00 00 00 00 c8 fe 00 00 fe fe 01 20 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: d4 30 80 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 18 10 05 00 00 a0 80 00 80 30 00 00 41 44 44 11 f0: 5a ff 5f bf 00 00 00 c0 10 00 00 00 00 00 00 00 00:0a.2 RAM memory [0500]: nVidia Corporation MCP51 Memory Controller 0 [10de:0272] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 72 02 00 04 a0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 10 00 00 10 00 00 10 10 50: 10 10 10 10 00 00 00 00 00 00 00 00 00 00 00 00 60: 02 03 00 00 12 00 00 00 02 00 00 00 10 01 12 00 70: 32 33 00 00 03 00 00 00 00 00 00 00 12 01 00 00 80: 10 00 00 00 00 00 00 00 00 00 00 00 30 02 00 00 90: 00 00 00 00 01 20 00 00 01 00 00 00 00 09 00 00 a0: 01 02 00 00 00 10 00 00 05 00 00 00 01 00 00 00 b0: 00 10 00 80 01 00 00 80 00 00 00 00 02 00 00 00 c0: 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026d] (rev a2) (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00: de 10 6d 02 07 00 b0 00 a2 10 03 0c 00 00 80 00 10: 00 f0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 01 40: 7b 14 26 1c 01 00 02 fe 00 00 00 00 00 00 00 00 50: 00 00 00 00 1d 47 40 00 10 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller [10de:026e] (rev a2) (prog-if 20 [EHCI]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 10 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00: de 10 6e 02 06 00 b0 00 a2 20 03 0c 00 00 80 00 10: 00 e0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 02 03 01 40: 7b 14 26 1c 0a 80 98 20 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 01 00 00 60 18 85 03 3c 0a 01 00 00 00 00 70: 00 00 08 05 00 10 20 80 89 3d b6 22 77 25 04 00 80: 01 00 02 fe 00 00 00 00 00 00 00 00 15 16 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 00 00 00 08 80 00 00 00 00 00 00 00 00 b0: 33 00 11 22 00 00 00 00 ff 00 00 00 00 00 00 00 c0: 10 10 2d 0d 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f400 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: AMD_IDE Kernel modules: ide-pci-generic, amd74xx, ata_generic 00: de 10 65 02 05 00 b0 00 a1 8a 01 01 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 f4 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01 40: 7b 14 26 1c 01 00 02 00 00 00 00 00 00 00 00 00 50: 03 f0 01 00 00 00 00 00 a8 a8 a8 20 2a 00 99 20 60: 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 80 70 98 79 00 00 02 10 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:0e.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller [10de:0266] (rev a1) (prog-if 85 [Master SecO PriO]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 09f0 [size=8] Region 1: I/O ports at 0bf0 [size=4] Region 2: I/O ports at 0970 [size=8] Region 3: I/O ports at 0b70 [size=4] Region 4: I/O ports at e000 [size=16] Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: sata_nv Kernel modules: ide-pci-generic, ata_generic, sata_nv 00: de 10 66 02 07 00 b0 00 a1 85 01 01 00 00 00 00 10: f1 09 00 00 f1 0b 00 00 71 09 00 00 71 0b 00 00 20: 01 e0 00 00 00 d0 02 fe 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 03 01 40: 7b 14 26 1c 01 b0 02 00 00 00 00 00 00 00 00 00 50: 07 00 00 00 00 00 00 00 a8 20 a8 20 66 00 20 20 60: 00 c7 00 c6 51 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 00 80: 00 00 00 c0 00 c0 8f 23 00 00 58 80 00 d0 ba 16 90: 00 00 08 80 00 00 00 00 06 00 06 10 00 00 01 01 a0: 14 10 00 2c 00 00 00 00 00 00 00 00 33 33 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 03 a8 d0: 0a 00 02 28 42 00 00 00 00 00 00 00 40 03 60 e0 e0: 0a 00 02 26 42 00 00 00 00 00 00 00 e0 01 04 e1 f0: 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00:0f.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller [10de:0267] (rev a1) (prog-if 85 [Master SecO PriO]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 09e0 [size=8] Region 1: I/O ports at 0be0 [size=4] Region 2: I/O ports at 0960 [size=8] Region 3: I/O ports at 0b60 [size=4] Region 4: I/O ports at cc00 [size=16] Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: sata_nv Kernel modules: ide-pci-generic, ata_generic, sata_nv 00: de 10 67 02 07 00 b0 00 a1 85 01 01 00 00 00 00 10: e1 09 00 00 e1 0b 00 00 61 09 00 00 61 0b 00 00 20: 01 cc 00 00 00 c0 02 fe 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01 40: 7b 14 26 1c 01 b0 02 00 00 00 00 00 00 00 00 00 50: 07 00 00 00 00 00 00 00 a8 a8 a8 a8 aa 00 99 99 60: 00 00 00 00 51 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 00 80: 00 00 00 c0 b6 ba d3 17 00 00 73 1a aa f0 95 ff 90: 00 00 7d 14 00 00 00 00 06 00 06 10 00 00 01 01 a0: 14 10 00 00 00 00 00 00 00 00 00 00 33 33 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 03 a8 d0: 0a 00 02 28 42 00 00 00 00 00 00 00 10 14 00 00 e0: 0a 00 02 26 42 00 00 00 00 00 00 00 0f 00 10 00 f0: 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: fdb00000-fdbfffff Prefetchable memory behind bridge: fda00000-fdafffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+ BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: [b8] Subsystem: Gammagraphx, Inc. Device [0000:0000] Capabilities: [8c] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 6f 02 07 00 b0 00 a2 01 04 06 00 00 81 00 10: 00 00 00 00 00 00 00 00 00 04 04 20 90 90 80 82 20: b0 fd b0 fd a0 fd a0 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 b8 00 00 00 00 00 00 00 ff 00 04 02 40: 00 00 03 00 01 00 02 00 05 00 00 00 00 00 44 00 50: 00 00 fe 7f 00 00 00 00 ff 1f ff 1f 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 07 00 00 84 f0 bf fd 00 00 00 00 08 00 01 a8 90: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00 a0: 06 00 00 00 00 00 00 00 00 00 00 00 02 00 00 00 b0: 00 00 00 00 ff ff 00 00 0d 8c 00 00 00 00 00 00 c0: 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio [10de:026c] (rev a2) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin B routed to IRQ 11 Region 0: Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00: de 10 6c 02 06 00 b0 00 a2 00 03 04 00 00 80 00 10: 00 40 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 02 05 40: 7b 14 26 1c 01 50 02 c0 00 00 00 00 01 01 0f 00 50: 05 6c 80 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 03 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 46 00 29 00 00 00 00 00 00 00:14.0 Bridge [0680]: nVidia Corporation MCP51 Ethernet Controller [10de:0269] (rev a1) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at c800 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=0 PME- Kernel driver in use: forcedeth Kernel modules: forcedeth 00: de 10 69 02 07 00 b0 00 a1 00 80 06 00 00 00 00 10: 00 b0 02 fe 01 c8 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 01 14 40: 7b 14 26 1c 01 00 02 fe 00 01 00 00 0b 00 00 10 50: 05 6c 84 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 02 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 11 00 00 00 42 01 00 00 00 00 00 00 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 60: 00 00 00 00 e4 00 00 00 0f cc 0e 0f 0c 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 00 01 21 20 00 11 11 22 06 75 80 02 00 00 00 90: 69 01 61 01 00 00 04 00 07 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 7f 00 00 00 00 00 01 00 00 00 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00 80: 03 0a 00 00 00 0b 00 00 00 00 00 00 00 00 00 00 90: 03 00 80 00 00 ff ef 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 03 00 f4 00 00 02 fe 00 b0: 03 00 f0 00 80 4f f0 00 00 00 00 00 00 00 00 00 c0: 13 80 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 03 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 00 00 00 01 01 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: e0 3e 78 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00 80: 02 00 00 00 00 00 00 00 24 c2 bc 5d 20 13 13 00 90: 10 0c 01 00 5b 80 10 77 24 00 00 80 20 25 20 00 a0: ed 02 00 5d 00 00 00 00 00 00 00 00 00 00 00 00 b0: d4 e2 73 f7 79 00 00 00 eb ab 0c 10 40 11 00 0a c0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 65 84 11 15 26 3e 01 82 82 3a 64 a3 b9 19 21 2c e0: 00 23 12 48 4b e0 10 08 24 02 28 a3 10 00 e9 1c f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: ff 3b 04 00 40 00 10 02 00 00 00 00 00 00 00 00 50: 40 a1 14 84 85 00 00 00 00 00 00 00 c0 ef af 6b 60: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 11 01 12 51 21 20 30 50 00 2a 00 08 2e 22 00 00 80: 00 00 07 23 13 21 13 21 00 00 00 00 00 00 00 00 90: 00 00 00 00 c9 0a 00 00 10 e0 f0 76 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 01 a7 0d 00 00 00 40 08 25 25 25 00 e0: 00 00 00 00 24 22 4e 00 19 07 00 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 f2 0f 04 00 04:07.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:1c26] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at fdbf8000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ohci1394 Kernel modules: ohci1394 00: 4c 10 23 80 06 00 10 02 00 10 00 0c 10 40 00 00 10: 00 f0 bf fd 00 80 bf fd 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 26 1c 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 02 04 40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 88 00 00 00 f0: 10 00 00 00 82 10 00 00 7b 14 26 1c 00 00 00 00 # superiotool -deV superiotool r3125 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x8400, id=0x6388 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x8863, rev=0xf Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627EHF/EF/EHG/EG (id=0x88, rev=0x63) at 0x2e Register dump: idx 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f val 88 63 ff 00 84 00 00 ff 50 00 7c c0 08 01 00 ff def 88 MM ff 00 MM 00 MM RR 50 04 00 RR 00 21 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 01 03 f0 06 02 0e 00 ff 00 00 def 01 03 f0 06 02 8e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 00 00 00 00 04 38 def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 00 00 00 00 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 00 00 00 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 80 def 01 00 60 00 64 01 0c 83 LDN 0x06 (Serial flash interface) idx 30 62 63 val 00 ff ff def 00 00 00 LDN 0x07 (GPIO 1, GPIO 6, game port, MIDI port) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 f7 val 01 00 00 00 00 00 fd 00 00 02 ff ff ff 00 def 00 02 01 03 30 09 ff 00 00 00 ff 00 00 00 LDN 0x08 (WDTO#, PLED) idx 30 f5 f6 f7 val 00 ff 00 ff def 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5, SUSLED) idx 30 e0 e1 e2 e3 e4 e5 f0 f1 f2 f3 f4 f5 f6 f7 val 00 ff ff ff ff ff ff ff ff ff 00 ff ff ff ff def 00 ff 00 00 ff 00 00 ff 00 00 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 e8 f2 f3 f4 f6 f7 val 00 00 00 00 23 26 00 00 1c 00 09 7c 00 00 00 00 def 00 00 01 00 ff 08 00 RR 00 00 RR 7c 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 f1 val 01 02 90 00 c1 3f def 00 00 00 00 c1 00 Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff # exit Script done on Fri 09 Apr 2010 11:57:25 AM EDT

2 1

[commit] r1042 - trunk
by repository service 13 Jun '10

13 Jun '10

Author: mkarcher Date: Sun Jun 13 01:14:03 2010 New Revision: 1042 URL: http://flashrom.org/trac/coreboot/changeset/1042 Log: Unbreak flashrom - fix compiler error (trivial) Fix compiler error (bad forward port in r1040). Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Modified: trunk/board_enable.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sun Jun 13 01:07:26 2010 (r1041) +++ trunk/board_enable.c Sun Jun 13 01:14:03 2010 (r1042) @@ -659,7 +659,7 @@ /** * Suited for MSI K8N Neo2 Platinum: Socket 939 + nForce3 Ultra + CK8. */ -static int nvidia_mcp_gpio0c_raise(const char *name) +static int nvidia_mcp_gpio0c_raise(void) { return nvidia_mcp_gpio_set(0x0c, 1); }

1 0

[commit] r1041 - trunk
by repository service 13 Jun '10

13 Jun '10

Author: mkarcher Date: Sun Jun 13 01:07:26 2010 New Revision: 1041 URL: http://flashrom.org/trac/coreboot/changeset/1041 Log: Board-enable for MS-7025 (K8N Neo2 Platinum) test report is http://www.coreboot.org/pipermail/flashrom/2010-April/002967.html Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Tested-by: Valentine "Pegasus rider" Yatsenko <mr.qweo(a)gmail.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/board_enable.c trunk/chipset_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sat Jun 12 19:27:44 2010 (r1040) +++ trunk/board_enable.c Sun Jun 13 01:07:26 2010 (r1041) @@ -562,6 +562,7 @@ case 0x0030: /* CK804 */ case 0x0050: /* MCP04 */ case 0x0060: /* MCP2 */ + case 0x00E0: /* CK8 */ break; case 0x0260: /* MCP51 */ case 0x0364: /* MCP55 */ @@ -656,6 +657,14 @@ } /** + * Suited for MSI K8N Neo2 Platinum: Socket 939 + nForce3 Ultra + CK8. + */ +static int nvidia_mcp_gpio0c_raise(const char *name) +{ + return nvidia_mcp_gpio_set(0x0c, 1); +} + +/** * Suited for ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04. */ static int nvidia_mcp_gpio10_raise(void) @@ -1479,6 +1488,7 @@ {0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, NULL, NULL, NULL, "MSI", "MS-6702E (K8T Neo2-F)", 0, OK, w83627thf_gpio4_4_raise_2e}, {0x1106, 0x0571, 0x1462, 0x7120, 0x1106, 0x3065, 0x1462, 0x7120, NULL, NULL, NULL, "MSI", "MS-6712 (KT4V)", 0, OK, board_msi_kt4v}, {0x1039, 0x7012, 0x1462, 0x0050, 0x1039, 0x6325, 0x1462, 0x0058, NULL, NULL, NULL, "MSI", "MS-7005 (651M-L)", 0, OK, board_msi_651ml}, + {0x10DE, 0x00E0, 0x1462, 0x0250, 0x10DE, 0x00E1, 0x1462, 0x0250, NULL, NULL, NULL, "MSI", "MS-7025 (K8N Neo2 Platinum)", 0, OK, nvidia_mcp_gpio0c_raise}, {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, NULL, "MSI", "MS-7046", 0, OK, intel_ich_gpio19_raise}, {0x10DE, 0x005E, 0x1462, 0x7135, 0x10DE, 0x0050, 0x1462, 0x7135, NULL, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", 0, OK, w83627thf_gpio4_4_raise_4e}, {0x10DE, 0x0270, 0x1462, 0x7207, 0x10DE, 0x0264, 0x1462, 0x7207, NULL, NULL, NULL, "MSI", "MS-7207 (K8N GM2-L)", 0, NT, nvidia_mcp_gpio2_raise}, Modified: trunk/chipset_enable.c ============================================================================== --- trunk/chipset_enable.c Sat Jun 12 19:27:44 2010 (r1040) +++ trunk/chipset_enable.c Sun Jun 13 01:07:26 2010 (r1041) @@ -1353,6 +1353,7 @@ {0x10de, 0x0050, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* LPC */ {0x10de, 0x0051, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* Pro */ {0x10de, 0x0060, OK, "NVIDIA", "NForce2", enable_flash_nvidia_nforce2}, + {0x10de, 0x00e0, OK, "NVIDIA", "NForce3", enable_flash_nvidia_nforce2}, /* Slave, should not be here, to fix known bug for A01. */ {0x10de, 0x00d3, OK, "NVIDIA", "CK804", enable_flash_ck804}, {0x10de, 0x0260, NT, "NVIDIA", "MCP51", enable_flash_ck804}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Sat Jun 12 19:27:44 2010 (r1040) +++ trunk/print.c Sun Jun 13 01:07:26 2010 (r1041) @@ -377,6 +377,7 @@ B("MSI", "MS-6702E (K8T Neo2-F)",1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=588", NULL), B("MSI", "MS-6712 (KT4V)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=505", NULL), B("MSI", "MS-7005 (651M-L)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=559", NULL), + B("MSI", "MS-7025 (K8N Neo2 Platinum)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=587", NULL), B("MSI", "MS-7046", 1, "http://www.heimir.de/ms7046/", NULL), B("MSI", "MS-7065", 1, "http://browse.geekbench.ca/geekbench2/view/53114", NULL), B("MSI", "MS-7135 (K8N Neo3)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=170", NULL),

1 0

Re: [flashrom] [PATCH] Board enable for EPIA EK
by Carl-Daniel Hailfinger 13 Jun '10

13 Jun '10

On 11.04.2010 13:17, Michael Karcher wrote: > Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> > No response from the owner of that board, so I'd say commit it as untested. Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel -- http://www.hailfinger.org/

2 2

Flashrom failed on Gigabyte GA-8IRML (Rev. 2.2) with bios F8
by Putlinuxonit 12 Jun '10

12 Jun '10

Hi, Just reporting a failure on the Gigabyte GA-8IRML (Rev 2.2) with bios F8. flashrom (0.9.2-r1023) appears to read (backup) the bios fine OK but fails on first sector/bit when attempting erase before write. Please see attached logs. idlogin, bios download page http://www.gigabyte.com.tw/products/product-page.aspx?pid=1343#dl <http://www.gigabyte.com.tw/products/product-page.aspx?pid=1343#dl>sticker on bios says Phoenix Bios

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom