- flashrom - mail.coreboot.org

Need assistance for using non-coreboot bios image
by David Bein 20 Apr '11

20 Apr '11

Hello ... I am very impressed with flashrom. I just used it on a motherboard based on the Lynnfield 3420 chipset and it worked very well and is much faster than the AMI supplied equivalent. I have one problem which is that the very first boot after flashing the bios rom image, the bios complains about a CMOS checksum error and patiently waits for some input. I am assuming others have been here before. What I did next was enter the bios menu and tell it to save changes (none made). All boots after this no longer complain about the CMOS checksum. The reason flashrom is interesting to us (aside from not being restricted by AMI) is for unattended use in customer upgrade situations. Having any upgrade path require a human to type something is a bit of a problem. Any helpful hints will be greatly appreciated. Last but not least, thank you to all of you whole have put a lot of effort into this tool for use by coreboot and others. This really validates why open source is needed in the first place. --David

2 1

Re: [flashrom] Writing BIOS to General Electric CR11 single board computer
by Idwer Vollering 19 Apr '11

19 Apr '11

2011/4/19 Razee, Robert G (DS-1) <RRazee(a)drs-ds.com>: > Designation: Non-SSA/Finmeccanica > > This e-mail is basically a re-submittal with different subject. > > I am currently working with an Intel based controller that is not supported by FLASHROM. > The controller was purchased with AMI BIOS which configures the South Bridge BIOS_CNTL register to only allow SMI code to update the BIOS. > > > I have attached log files from the following: > > flashrom -V > flashrom.log "FlashRom was extracted from svn on 4/19/2011 and built with no changes." > lspci -nnvvxxx > lspci.log > superiotool -deV > superiotool.log > > biosdecode > biosdecode.log > hwinfo --bios > hwinfo-bios.log > dmidecode --type bios > dmidecode-bios.log lshw > lshw.log > > > The controller (CR11) is manufactured by GE and uses the following chipset: Do you have a contact at GE, that can help you with this controller ? > > Intel Celeron Processor > Intel E7520 North Bridge > Intel 6300ESB South Bridge > SST49LF008A Firmware Hub > > With minor tweaks to flashrom, it was able to see the following: > > Found chip "SST SST49LF008A" (1024 KB, FWH) at physical address 0xfff00000 Can we have a look at your modification/patch, if you are (legally) allowed to disclose your work ? > > The FWH ID was found at 0xfffc0000 and 0xfffc0001. > > Any help will be greatly appreciated. We are in need of a reflash utility other than the one supplied by AMI . > > > Thanks, > > > Robert G. Razee > Senior Software Engineer > DRS Consolidated Controls Inc. > 21 South Street > Danbury, CT 06810 > Tel: (203) 730-6808 > Email: RRazee(a)DRS-DS.com > > 3.1.1001 > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > http://www.flashrom.org/mailman/listinfo/flashrom >

2 1

Re: [flashrom] Writing BIOS to General Electric CR11 single board computer
by Razee, Robert G (DS-1) 19 Apr '11

19 Apr '11

Designation: Non-SSA/Finmeccanica Oops, the attachments got dropped on the first attempt. Robert G. Razee Senior Software Engineer DRS Consolidated Controls Inc. 21 South Street Danbury, CT 06810 Tel: (203) 730-6808 Email: RRazee(a)DRS-DS.com -----Original Message----- From: Razee, Robert G (DS-1) Sent: Tuesday, April 19, 2011 1:10 PM To: flashrom(a)flashrom.org Cc: Razee, Robert G (DS-1) Subject: RE: [flashrom] Writing BIOS to General Electric CR11 single board computer Designation: Non-SSA/Finmeccanica This e-mail is basically a re-submittal with different subject. I am currently working with an Intel based controller that is not supported by FLASHROM. The controller was purchased with AMI BIOS which configures the South Bridge BIOS_CNTL register to only allow SMI code to update the BIOS. I have attached log files from the following: flashrom -V > flashrom.log "FlashRom was extracted from svn on 4/19/2011 and built with no changes." lspci -nnvvxxx > lspci.log superiotool -deV > superiotool.log biosdecode > biosdecode.log hwinfo --bios > hwinfo-bios.log dmidecode --type bios > dmidecode-bios.log lshw > lshw.log The controller (CR11) is manufactured by GE and uses the following chipset: Intel Celeron Processor Intel E7520 North Bridge Intel 6300ESB South Bridge SST49LF008A Firmware Hub With minor tweaks to flashrom, it was able to see the following: Found chip "SST SST49LF008A" (1024 KB, FWH) at physical address 0xfff00000 The FWH ID was found at 0xfffc0000 and 0xfffc0001. Any help will be greatly appreciated. We are in need of a reflash utility other than the one supplied by AMI . Thanks, Robert G. Razee Senior Software Engineer DRS Consolidated Controls Inc. 21 South Street Danbury, CT 06810 Tel: (203) 730-6808 Email: RRazee(a)DRS-DS.com 3.1.1001 3.1.1001

1 0

Re: [flashrom] Writing BIOS to General Electric CR11 single board computer
by Razee, Robert G (DS-1) 19 Apr '11

19 Apr '11

Designation: Non-SSA/Finmeccanica This e-mail is basically a re-submittal with different subject. I am currently working with an Intel based controller that is not supported by FLASHROM. The controller was purchased with AMI BIOS which configures the South Bridge BIOS_CNTL register to only allow SMI code to update the BIOS. I have attached log files from the following: flashrom -V > flashrom.log "FlashRom was extracted from svn on 4/19/2011 and built with no changes." lspci -nnvvxxx > lspci.log superiotool -deV > superiotool.log biosdecode > biosdecode.log hwinfo --bios > hwinfo-bios.log dmidecode --type bios > dmidecode-bios.log lshw > lshw.log The controller (CR11) is manufactured by GE and uses the following chipset: Intel Celeron Processor Intel E7520 North Bridge Intel 6300ESB South Bridge SST49LF008A Firmware Hub With minor tweaks to flashrom, it was able to see the following: Found chip "SST SST49LF008A" (1024 KB, FWH) at physical address 0xfff00000 The FWH ID was found at 0xfffc0000 and 0xfffc0001. Any help will be greatly appreciated. We are in need of a reflash utility other than the one supplied by AMI . Thanks, Robert G. Razee Senior Software Engineer DRS Consolidated Controls Inc. 21 South Street Danbury, CT 06810 Tel: (203) 730-6808 Email: RRazee(a)DRS-DS.com 3.1.1001

1 0

Re: [flashrom] Writing BIOS via SMI
by Idwer Vollering 19 Apr '11

19 Apr '11

2011/4/15 Razee, Robert G (DS-1) <RRazee(a)drs-ds.com>: > Designation: Non-SSA/Finmeccanica > > I am currently working with an Intel based controller that is not supported > by FLASHROM. The controller was purchased with AMI BIOS which configures the > South Bridge BIOS_CNTL register to only allow SMI code to update the BIOS. > Is there any work being done to provide BIOS writing via SMI? > > > > The controller (CR11) is manufactured by GE and uses the following chipset: > > > > Intel Celeron Processor > > Intel E7520 North Bridge > > Intel 6300ESB South Bridge The 6300ESB chipset is known to be supported: http://flashrom.org/Supported_hardware#Supported_chipsets > > SST49LF008A Firmware Hub > > > > I have been able to get FLASHROM to find the firmware hub, but it cannot > successfully write the BIOS. The AMI utility is using an SMI handler to > perform the BIOS updates. IMHO BLE should be set to 0 and BIOSWE should be set to 1. http://www.intel.com/Assets/PDF/datasheet/300641.pdf 8.1.12 Offset 4E - 4Fh: BIOS_CNTL (LPC I/F—D31:F0) > > > > Any information regarding this issue would be greatly appreciated. Can you re-run flashrom like this: "flashrom -V" ? > > > > > > > > Robert G. Razee > > Senior Software Engineer > > DRS Consolidated Controls Inc. > > 21 South Street > > Danbury, CT 06810 > > Tel: (203) 730-6808 > > Email: RRazee(a)DRS-DS.com > > > > 3.1.1001 > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > http://www.flashrom.org/mailman/listinfo/flashrom >

2 1

Fw: Help: trouble when flashing rom
by Stefan Tauner 19 Apr '11

19 Apr '11

hello cyrille please try to always "reply to all" to include the flashrom.org address in destinations. you will get faster and better answers. i dont have time now to look at that problem, but it does not look too good from a first glance imho. Begin forwarded message: Date: Tue, 19 Apr 2011 07:42:36 +0200 From: Cyrille Bartholomée <cyrille(a)bartholomee.com> To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Subject: Re: [flashrom] Help: trouble when flashing rom Dear Stefan, First of all thank you for responding so fast and trying to help me! Just built checkout from svn. It outputs this result: flashrom v0.9.3-r1288 on Linux 2.6.35-28-generic (i686), built with libpci 3.1.7, GCC 4.4.5, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... delay loop is unreliable, trying to continue OK. Found chipset "Intel ICH4-M", enabling flash write... OK. This chipset supports the following protocols: FWH. Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling checks. Erasing and writing flash chip... ERASE FAILED at 0x00016000! Expected=0xff, Read=0xae, failed byte count from 0x00016000-0x00016fff: 0xfde ERASE FAILED! ERASE FAILED at 0x00010000! Expected=0xff, Read=0xca, failed byte count from 0x00010000-0x0001ffff: 0xfeb2 ERASE FAILED! Segmentatiefout Segmentatiefout=segmentation error I am using an Asus laptop model M6Ne, the exact type of board I don't know. I've attached some information based on output using the following commands: flashrom -V, lspci -nnvvvxxx and superiotool -deV. Maybe this can help you? Again, thanks for your help. Kind regards, Cyrille Bartholomée | De Damhouderestraat 20 | 2018 Antwerpen t. 0032 3 298 4244 | m. 0032 499 711 018 | e. cyrille(a)bartholomee.com Op dinsdag 19 april 2011 00:41:24 schreef u: > On Mon, 18 Apr 2011 21:25:07 +0200 > Cyrille Bartholomée <cyrille(a)bartholomee.com> wrote: > > > Dear, > > > > I'm facing this problem when flashing my rom: > > > > flashrom v0.9.2-r1028 on Linux 2.6.35-28-generic (i686), built with > > if possible please try a newer version and provide us a verbose log > (-V parameter). either 0.9.3 or even better compile the svn version > from source: http://flashrom.org/Downloads > -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] Help: trouble when flashing rom
by Idwer Vollering 19 Apr '11

19 Apr '11

Please use "reply to all" in the future. Thanks. 2011/4/19 Cyrille Bartholomée <cyrille(a)bartholomee.com> > > Dear Idwer, > > First of all thank you for responding so fast and trying to help me! First of all: DO NOT REBOOT OR POWEROFF YOUR LAPTOP. > > 1. Downloaded and built latest flashrom. Problem remains exactly the same as with previous version. That is good and not so good. > 2. I am using an Asus laptop model M6Ne, the exact type of board I don't know. flashrom doesn't really support laptops. However, adding support *is* possible but requires a lot of work. http://flashrom.org/Supported_hardware#Supported_laptops.2Fnotebooks http://flashrom.org/Laptops > > 3. I have run the commands you mentioned, the results are attached to this mail. This information is not sane, it should say (and we detect it as such) "Laptop" or "Notebook": DMI string chassis-type: "<OUT OF SPEC>" Don't worry, this is not your fault. > > If there is more information you need, please let me know. DO NOT REBOOT OR POWEROFF YOUR LAPTOP. I have uploaded the content of the files you have attached. flashrom -V: http://paste.flashrom.org/view.php?id=493 lspci -nnvvvxxx: http://paste.flashrom.org/view.php?id=494 superiotool -deV: http://paste.flashrom.org/view.php?id=495 > > Again, thanks for your help. > > Kind regards, > > Cyrille Bartholomée | De Damhouderestraat 20 | 2018 Antwerpen > > t. 0032 3 298 4244 | m. 0032 499 711 018 | e. cyrille(a)bartholomee.com > > Op dinsdag 19 april 2011 00:21:28 schreef u: > > > 2011/4/18 Cyrille Bartholomée <cyrille(a)bartholomee.com>: > > > > Dear, > > > > > > > > I'm facing this problem when flashing my rom: > > > > > > > > flashrom v0.9.2-r1028 on Linux 2.6.35-28-generic (i686), built with libpci > > > > 3.0.0, GCC 4.4.4, little endian > > > > > > > > flashrom is free software, get the source code at http://www.flashrom.org > > > > > > > > Calibrating delay loop... delay loop is unreliable, trying to continue OK. > > > > > > > > No coreboot table found. > > > > > > > > Found chipset "Intel ICH4-M", enabling flash write... OK. > > > > > > > > This chipset supports the following protocols: Non-SPI. > > > > > > > > Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. > > > > > > > > Flash image seems to be a legacy BIOS. Disabling checks. > > > > > > > > Writing flash chip... Erasing flash chip... ERASE FAILED at 0x00000008! > > > > Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x00000fff: > > > > 0xfc5 > > > > > > > > ERASE FAILED! > > > > > > > > ERASE FAILED at 0x00000008! Expected=0xff, Read=0x00, failed byte count from > > > > 0x00000000-0x0000ffff: 0xfadb > > > > > > > > ERASE FAILED! > > > > > > > > FAILED! > > > > > > > > ERASE FAILED! > > > > > > > > FAILED! > > > > > > > > Your flash chip is in an unknown state. > > > > > > > > Get help on IRC at irc.freenode.net (channel #flashrom) or > > > > > > > > mail flashrom(a)flashrom.org! > > > > > > Can you: > > > - try a newer release (or build the latest developemt code yourself > > > http://www.flashrom.org/Downloads#Installation_from_source) > > > - mention the exact name of your board (including revision, if there > > > are multiple revisions) > > > - attach the output of 'flashrom -V', 'lspci -nnvvvxxx', 'superiotool > > > -deV' (run all commands as root) > > > > > > > > > Thanks in advance, > > > Idwer > > > > > > > > > > > ------------------------------------------------------------------------------- > > > > > > > > DO NOT REBOOT OR POWEROFF! > > > > > > > > Regards, > > > > > > > > Cyrille Bartholomée | De Damhouderestraat 20 | 2018 Antwerpen > > > > > > > > t. 0032 3 298 4244 | m. 0032 499 711 018 | e. cyrille(a)bartholomee.com > > > > > > > > _______________________________________________ > > > > flashrom mailing list > > > > flashrom(a)flashrom.org > > > > http://www.flashrom.org/mailman/listinfo/flashrom > > > > > > >

1 0

DB43LD MainBoard
by Rusty Dodson 18 Apr '11

18 Apr '11

I want to use flashrom to update the Intel DB43LD Mainboard BIOS. I have used the Intel tool to create a .BIO file and a .INI file to get the bios to the version desired and to define the default settings. It appears that flashrom should be successful even though the MB is not mentioned. I have attached the output of the 'flashrom -VV' command. I compiled and used the 0.9.3 release Would you please provide any additional insight you may feel is relevant. -Thanks ________________________________________________________________________________________________________________ flashrom v0.9.3-r1205 on Linux 2.6.29 (i686), built with libpci 3.1.7, GCC 4.3.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 2629M loops per second, 10 myus = 11 us, 100 myus = 99 us, 1000 myus = 986 us, 10000 myus = 9834 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "XXXXXXXXXXXXXXX" DMI string system-product-name: "XXXXX" DMI string system-version: " " DMI string baseboard-manufacturer: "Intel Corporation" DMI string baseboard-product-name: "DB43LD" DMI string baseboard-version: "AAE60577-202" DMI string chassis-type: "Desktop" Found chipset "Intel ICH10D", enabling flash write... chipset PCI ID is 8086:3a1a, 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x3 Root Complex Register Block address = 0xfed1c000 GCS = 0x521465: BIOS Interface Lock-Down: enabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) FLOCKDN 1, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x00000000 (FREG0: Flash Descriptor) 0x00000000-0x00000fff is read-only 0x58: 0x03ff0280 (FREG1: BIOS) 0x00280000-0x003fffff is read-write 0x5C: 0x02770003 (FREG2: Management Engine) 0x00003000-0x00277fff is locked 0x60: 0x00020001 (FREG3: Gigabit Ethernet) 0x00001000-0x00002fff is read-write 0x64: 0x027f0278 (FREG4: Platform Data) 0x00278000-0x0027ffff is read-write 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x00424004 (SSFS, SSFC) 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00004000 (FDOC) WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L05PT, 64 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L05PU, 64 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L10PT, 128 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L10PU, 128 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L20PT, 256 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L20PU, 256 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L40PT, 512 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L40PU, 512 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L80P, 1024 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L16PT, 2048 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L16PU, 2048 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L512, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L010, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L020, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L040, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L080, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L016, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25L032, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A25LQ032, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF081A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25DQ161, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Bright BM29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EMST F25L008A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B05T, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B10T, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B20T, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B40T, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B80T, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B16T, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B32T, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25B64T, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Eon EN29F010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Hyundai HY29F040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L1635E, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L3205" (4096 KB, SPI) at physical address 0xffc00000. Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Numonyx M25PE40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x2f, id2 0x43, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST25VF064C, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST25VF040.REMS, 512 KB: Invalid OPCODE 0x90 Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST25LF040A.RES, 512 KB: Invalid OPCODE 0xab Probing for SST SST25VF040B.REMS, 512 KB: Invalid OPCODE 0x90 Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x2f, id2 0x43, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xcb, id2 0x3e, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25PX32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M25PX64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BB, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x2f, id2 0x43, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25Q80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25Q16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25Q32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25Q64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040/P, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040(F)B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040(F)C, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49F002U/N, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49F020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x2f, id2 0x43, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x85, id2 0x3a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x74, id2 0xaf, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Eon unknown Eon SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016 Not unmapping zero size at 0xffffffff Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. Invalid OPCODE 0x90 Not unmapping zero size at 0xffffffff === This flash part has status UNTESTED for operations: ERASE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified.

2 3

adding a board_flash_disable
by Stefan Tauner 18 Apr '11

18 Apr '11

hello list! brandon/kiddyshaq34 came up with an interesting question: > <kiddyshaq34> "twice?" just kidding :P > <kiddyshaq34> I need to know how we are going to bring the ec out of > flash mode after flashrom runs > <kiddyshaq34> I know the system state notification and everything > <kiddyshaq34> but how do we run those ec commands after flashrom > runs(like probe, read and write)? so in hope to spare twice the pain i searched through the code and came up with the conclusion that we dont do such a thing as a board_flash_disable. so even if we just probe for a chip on a board with a board enable we dont leave the board in the same state as before. there was a discussion 3,5yrs ago, where there was consensus that this should be changed. http://www.coreboot.org/pipermail/coreboot/2007-October/025495.html but i guess there was just no need to implement it, since (quoting idwer:) "usually, users reboot (within, wild guess, 24 hours) after flashing". i will put this to my "open tasks you might wanna try to tackle sometime in the more or less distant future"-list, but maybe we can get a small discussion going now. i dont have any experience with board enables whatsoever. i know that usually its just a toggle of a gpio pin that disables the write protection pin etc, but sometimes there is more to do, especially when an EC is involved. we need to know how to undo what we do in board_enable. what could that possibly be and what data would we need to preserve? as a first step we could just add another function pointer to the board_pciid_enable struct which gets called by a new generic board_flash_disable function which gets called in internal_shutdown. we would probably want to share/store the const struct board_pciid_enable *board variable/constant obtained in board_flash_enable to be able to use it in board_flash_disable. we could then extend the board_pciid_enables table with function pointers to "static board disables" (i.e. undo functions that work without using runtime data (obtained/set by board_pciid_enable). this could then be extended to what carldani planned in 2007. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 1

Help: trouble when flashing rom
by Cyrille Bartholomée 18 Apr '11

18 Apr '11

Dear, I'm facing this problem when flashing my rom: flashrom v0.9.2-r1028 on Linux 2.6.35-28-generic (i686), built with libpci 3.0.0, GCC 4.4.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... delay loop is unreliable, trying to continue OK. No coreboot table found. Found chipset "Intel ICH4-M", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... ERASE FAILED at 0x00000008! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x00000fff: 0xfc5 ERASE FAILED! ERASE FAILED at 0x00000008! Expected=0xff, Read=0x00, failed byte count from 0x00000000-0x0000ffff: 0xfadb ERASE FAILED! FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! Regards, Cyrille Bartholomée | De Damhouderestraat 20 | 2018 Antwerpen t. 0032 3 298 4244 | m. 0032 499 711 018 | e. cyrille(a)bartholomee.com

3 2

Fwd: Flashing M/B Bios (Asus P5LD2-VM) goes wrong
by Idwer Vollering 17 Apr '11

17 Apr '11

---------- Forwarded message ---------- From: Emil Sirbu <emil(a)servicii.info.ro> Date: 2011/4/17 Subject: Re: [flashrom] Flashing M/B Bios (Asus P5LD2-VM) goes wrong To: Idwer Vollering <vidwer(a)gmail.com> On 04/17/2011 01:35 AM, Idwer Vollering wrote: > > 2011/4/16 Emil Sirbu<emil(a)servicii.info.ro>: >> >> On 04/16/2011 06:37 AM, Emil Sirbu wrote: >>> >>> Hello, >>> >>> >>> I have an ASUS P5LD2-VM, and I try to update bios, first with flashrom >>> v0.9.2-r1028 ( http://paste.flashrom.org/view.php?id=489 ) >>> then with 0.9.3 ( http://paste.flashrom.org/view.php?id=490 also, the ROM >>> is at http://paste.flashrom.org/uploads/491.bin ) >>> but: >>> >>> Writing flash chip... Erasing flash chip... Looking at blockwise erase >>> function 0... trying... 0x000000-0x000fff, 0x001000-0x001fff, >>> 0x002000-0x002fff, 0x003000-0xff, 0x004000-0x004fff, 0x005000-0x005fff, >>> ERASE FAILED at 0x00005760! Expected=0xff, Read=0x50, failed byte count from >>> 0x00005000-0x00005fff: 0x87a >>> ERASE FAILED! >>> >>> >> > It looks like the PCI IDs in the patch attached to this message can be > used for your board too: > http://www.flashrom.org/pipermail/flashrom/2010-October/005106.html > > Can you try the attached patch ? > Apply to svn code, r1288, with "patch -p0< > /path/to/board_enable_asus_p5ld2-vm.diff", recompile and try writing > with the patched binary: "./flashrom -w /path/to/P5LD2-VM-1401.ROM". > After you have done that, please report back here. Hi Idwer, I'm sorry but I remove the motherboard from my PC (I make a hardware upgrade, before this, I want to update BIOS because, from beginning, the motherboard was a problem with processor). If/when I find a chassis to mount and test (or when I have some time to remount on my system), I will send you the results. One more time, thank you for your great tool, Emil "carco" Sirbu

1 0

output of command "flashrom -V"
by Anthony Penzinski 16 Apr '11

16 Apr '11

Written on mainboard--Rev 1.02G flashrom v0.9.2-r1028 on Linux 2.6.35-28-generic (x86_64), built with libpci 3.0.0, GCC 4.4.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1297M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 998 us, 10000 myus = 10011 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M3N78-VM" DMI string baseboard-version: "Rev X.0x" DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8712 Found chipset "NVIDIA MCP78S", enabling flash write... chipset PCI ID is 10de:075c, This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Guessed flash bus type is SPI Found SMBus device 10de:0752 at 00:01:1 SPI BAR is at 0xfcf80000, after clearing low bits BAR is at 0xfcf80000 SPI control is 0xc01a, enable=0, idle=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org to help us finish support for your chipset. Thanks. SPI on this chipset is not supported yet. OK. This chipset supports the following protocols: None. SuperI/O ID 8712 is not on the controller list. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: skipped. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: skipped. Probing for Intel 82802AC, 1024 KB: skipped. Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: skipped. Probing for PMC Pm49FL004, 512 KB: skipped. Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: skipped. Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: skipped. Probing for SST SST49LF003A/B, 384 KB: skipped. Probing for SST SST49LF004A/B, 512 KB: skipped. Probing for SST SST49LF004C, 512 KB: skipped. Probing for SST SST49LF008A, 1024 KB: skipped. Probing for SST SST49LF008C, 1024 KB: skipped. Probing for SST SST49LF016C, 2048 KB: skipped. Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: skipped. Probing for ST M50FLW040B, 512 KB: skipped. Probing for ST M50FLW080A, 1024 KB: skipped. Probing for ST M50FLW080B, 1024 KB: skipped. Probing for ST M50FW002, 256 KB: skipped. Probing for ST M50FW016, 2048 KB: skipped. Probing for ST M50FW040, 512 KB: skipped. Probing for ST M50FW080, 1024 KB: skipped. Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS S29C31004T, 512 KB: skipped. Probing for SyncMOS S29C51001T, 128 KB: skipped. Probing for SyncMOS S29C51002T, 256 KB: skipped. Probing for SyncMOS S29C51004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: skipped. Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: skipped. Probing for Winbond W39V080FA, 1024 KB: skipped. Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for EON unknown EON SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically.

2 1

Fwd: Flashing M/B Bios (Asus P5LD2-VM) goes wrong
by Idwer Vollering 16 Apr '11

16 Apr '11

Forwarding the reply. ---------- Forwarded message ---------- From: Emil Sirbu <emil(a)servicii.info.ro> Date: 2011/4/16 Subject: Re: [flashrom] Flashing M/B Bios (Asus P5LD2-VM) goes wrong To: Idwer Vollering <vidwer(a)gmail.com> On 04/16/2011 05:40 PM, Idwer Vollering wrote: > > 2011/4/16 Emil Sirbu<emil(a)servicii.info.ro>: >> >> Hello, >> >> >> I have an ASUS P5LD2-VM, and I try to update bios, first with flashrom >> v0.9.2-r1028 ( http://paste.flashrom.org/view.php?id=489 ) >> then with 0.9.3 ( http://paste.flashrom.org/view.php?id=490 also, the ROM is >> at http://paste.flashrom.org/uploads/491.bin ) >> but: >> >> Writing flash chip... Erasing flash chip... Looking at blockwise erase >> function 0... trying... 0x000000-0x000fff, 0x001000-0x001fff, >> 0x002000-0x002fff, 0x003000-0xff, 0x004000-0x004fff, 0x005000-0x005fff, >> ERASE FAILED at 0x00005760! Expected=0xff, Read=0x50, failed byte count from >> 0x00005000-0x00005fff: 0x87a >> ERASE FAILED! >> >> >> Can you help whit this? > > There is a patch for a different version of the P5LD2: > http://www.flashrom.org/pipermail/flashrom/2010-October/005106.html > > Can you show the output of "lspci -nnvvvxxx" (as root) ? Either upload > it to http://paste.flashrom.org of add the output as an attachment. > I'm sory, I just replaced the motherboard (and I don't have other chasis to test). The motherboard was ok, I make a CD with DOS and I update BIOS with AFUDOS. Thank you very much, Emil "carco" Sirbu

1 0

evga sr-2 classified motherboard works with flashrom
by Andrew Burgess 16 Apr '11

16 Apr '11

read and write tested thank you! root@hogo:~ # flashrom -V flashrom v0.9.3-r1286 on Linux 2.6.38.2-4 (x86_64), built with libpci 3.1.7, GCC 4.5.1 20100907 (Red Hat 4.5.1-3), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 691M loops per second, delay more than 10% too short (got 55% of expected delay), recalculating... 1230M loops per second, 10 myus = 11 us, 100 myus = 98 us, 1000 myus = 1007 us, 10000 myus = 10064 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: "EVGA" DMI string baseboard-product-name: "EVGA Classified SR-2" DMI string baseboard-version: "X58" DMI string chassis-type: "Desktop" Found chipset "Intel ICH10R", enabling flash write... chipset PCI ID is 8086:3a16, 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2 Root Complex Register Block address = 0xfed1c000 GCS = 0x461: BIOS Interface Lock-Down: enabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x2008 (HSFS) FLOCKDN 0, FDV 0, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00000202 (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x02, BRRA 0x02 0x54: 0x00001fff (FREG0: Flash Descriptor) Flash Descriptor region is unused. 0x58: 0x00001fff (FREG1: BIOS) BIOS region is unused. 0x5C: 0x00001fff (FREG2: Management Engine) Management Engine region is unused. 0x60: 0x00001fff (FREG3: Gigabit Ethernet) Gigabit Ethernet region is unused. 0x64: 0x00001fff (FREG4: Platform Data) Platform Data region is unused. 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x04 (SSFS) AEL 0, FCERR 0, FDONE 1, SCIP 0 0x91: 0x004140 (SSFC) 0x94: 0x5006 (PREOP) 0x96: 0x462b (OPTYPE) 0x98: 0x05ab0302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV001BB, 128 KB: skipped. Probing for AMD Am29LV001BT, 128 KB: skipped. Probing for AMD Am29LV002BB, 256 KB: skipped. Probing for AMD Am29LV002BT, 256 KB: skipped. Probing for AMD Am29LV004BB, 512 KB: skipped. Probing for AMD Am29LV004BT, 512 KB: skipped. Probing for AMD Am29LV008BB, 1024 KB: skipped. Probing for AMD Am29LV008BT, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for Bright BM29F040, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Hyundai HY29F040A, 512 KB: skipped. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1635E, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29F040, 512 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xc7, id2 0x45, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Spansion S25FL032A, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Spansion S25FL064A, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF010.REMS, 128 KB: probe_spi_rems: id1 0xbf, id2 0x4a Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Chip status register is 00 Chip status register: Block Protect Write Disable (BPL) is not set Chip status register: Auto Address Increment Programming (AAI) is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "SST SST25VF032B" (4096 KB, SPI) at physical address 0xffc00000. Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xbf, id2 0x4a Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25LF040A.RES, 512 KB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0xbf, id2 0x4a Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xbf, id2 0x4a Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xc7, id2 0x45, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25PX16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25PX32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25PX64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xc7, id2 0x45, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Probing for Winbond W29C040/P, 512 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W39L040, 512 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U/N, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xc7, id2 0x45, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xbf, id2 0x4a === This flash part has status UNTESTED for operations: WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified. Restoring PCI config space for 00:1f:0 reg 0xdc

2 2

problem
by Cameron Just 16 Apr '11

16 Apr '11

2 1

Writing BIOS via SMI
by Razee, Robert G (DS-1) 15 Apr '11

15 Apr '11

Designation: Non-SSA/Finmeccanica I am currently working with an Intel based controller that is not supported by FLASHROM. The controller was purchased with AMI BIOS which configures the South Bridge BIOS_CNTL register to only allow SMI code to update the BIOS. Is there any work being done to provide BIOS writing via SMI? The controller (CR11) is manufactured by GE and uses the following chipset: Intel Celeron Processor Intel E7520 North Bridge Intel 6300ESB South Bridge SST49LF008A Firmware Hub I have been able to get FLASHROM to find the firmware hub, but it cannot successfully write the BIOS. The AMI utility is using an SMI handler to perform the BIOS updates. Any information regarding this issue would be greatly appreciated. Robert G. Razee Senior Software Engineer DRS Consolidated Controls Inc. 21 South Street Danbury, CT 06810 Tel: (203) 730-6808 Email: RRazee(a)DRS-DS.com 3.1.1001

1 0

[commit] r1288 - trunk
by repository service 14 Apr '11

14 Apr '11

Author: mkarcher Date: Fri Apr 15 02:03:37 2011 New Revision: 1288 URL: http://flashrom.org/trac/flashrom/changeset/1288 Log: Remove delays in JEDEC erase sequence It is extremely unlikely that a chip not requiring delays in probe does require them in erase. We observed unreliable erasing with a SST49LF004A with these delays, so remove them if the are not required. In review, I got the hint that "probe_jedec goes further by making that call conditional on nonzero delay". I decided to ignore that. For internal_delay, the small amount of clock cycles wasted for calling programmer_delay(0) is negligible compared to LPC cycle times. It might be an issue for 5 wasted bytes on the serial line in serprog. OTOH, flash erase is still slow compared to 6*5 bytes on a serial port at reasonable speed. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/jedec.c Modified: trunk/jedec.c ============================================================================== --- trunk/jedec.c Fri Apr 15 01:43:19 2011 (r1287) +++ trunk/jedec.c Fri Apr 15 02:03:37 2011 (r1288) @@ -242,21 +242,24 @@ unsigned int pagesize, unsigned int mask) { chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the Sector Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x30, bios + page); - programmer_delay(10); + programmer_delay(delay_us); /* wait for Toggle bit ready */ toggle_ready_jedec_slow(bios); @@ -272,21 +275,24 @@ unsigned int blocksize, unsigned int mask) { chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the Sector Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x50, bios + block); - programmer_delay(10); + programmer_delay(delay_us); /* wait for Toggle bit ready */ toggle_ready_jedec_slow(bios); @@ -302,21 +308,24 @@ { int total_size = flash->total_size * 1024; chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the JEDEC Chip Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x10, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); toggle_ready_jedec_slow(bios);

1 0

[commit] r1287 - trunk
by repository service 14 Apr '11

14 Apr '11

Author: mkarcher Date: Fri Apr 15 01:43:19 2011 New Revision: 1287 URL: http://flashrom.org/trac/flashrom/changeset/1287 Log: Remove erase_chip_stm50flw0x0x As the comment indicates, that function is not a chip erase function at all, but a function calling a block eraser in a loop. So it adds no extra value to what we already have in the block_eraser infrastructure. Furthermore, that function assumes a uniform sector size layout, but is referenced from flash chip with non-uniform sector size layout, which is just wrong. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/chipdrivers.h trunk/flashchips.c trunk/stm50flw0x0x.c Modified: trunk/chipdrivers.h ============================================================================== --- trunk/chipdrivers.h Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/chipdrivers.h Fri Apr 15 01:43:19 2011 (r1287) @@ -128,7 +128,6 @@ /* stm50flw0x0x.c */ int erase_sector_stm50flw0x0x(struct flashchip *flash, unsigned int block, unsigned int blocksize); -int erase_chip_stm50flw0x0x(struct flashchip *flash, unsigned int addr, unsigned int blocklen); int unlock_stm50flw0x0x(struct flashchip *flash); #endif /* !__CHIPDRIVERS_H__ */ Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/flashchips.c Fri Apr 15 01:43:19 2011 (r1287) @@ -6852,9 +6852,6 @@ }, { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6887,9 +6884,6 @@ }, { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6922,9 +6916,6 @@ }, { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6957,9 +6948,6 @@ }, { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6989,9 +6977,6 @@ {16 * 1024, 1}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {256 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7016,9 +7001,6 @@ { .eraseblocks = { {64 * 1024, 32}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7043,9 +7025,6 @@ { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7070,9 +7049,6 @@ { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7103,9 +7079,6 @@ {16 * 1024, 1}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, Modified: trunk/stm50flw0x0x.c ============================================================================== --- trunk/stm50flw0x0x.c Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/stm50flw0x0x.c Fri Apr 15 01:43:19 2011 (r1287) @@ -114,30 +114,3 @@ return 0; } - -/* FIXME: This function is not a real chip erase function. */ -int erase_chip_stm50flw0x0x(struct flashchip *flash, unsigned int addr, unsigned int blocklen) -{ - int i; - int total_size = flash->total_size * 1024; - int page_size = flash->page_size; - - if ((addr != 0) || (blocklen != flash->total_size * 1024)) { - msg_cerr("%s called with incorrect arguments\n", - __func__); - return -1; - } - - for (i = 0; i < total_size / page_size; i++) { - //if (unlock_block_stm50flw0x0x(flash, i * page_size)) { - // msg_cerr("UNLOCK FAILED!\n"); - // return -1; - //} - if (erase_block_82802ab(flash, i * page_size, page_size)) { - msg_cerr("ERASE FAILED!\n"); - return -1; - } - } - - return 0; -}

1 0

[commit] r1286 - trunk
by repository service 14 Apr '11

14 Apr '11

Author: mkarcher Date: Fri Apr 15 01:14:27 2011 New Revision: 1286 URL: http://flashrom.org/trac/flashrom/changeset/1286 Log: Board enable for Foxconn 6150K8MD-8EKRSH Reported by: wickberg(a)student.chalmers.se flashrom -V: http://paste.flashrom.org/view.php?id=452 lspci: http://paste.flashrom.org/view.php?id=453 (note that the flashrom dump is with a foreign chip. That board is originally equipped with an PMC Pm49FL004. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Stefan Reinauer <stefan.reinauer(a)coreboot.org> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sat Apr 2 13:47:21 2011 (r1285) +++ trunk/board_enable.c Fri Apr 15 01:14:27 2011 (r1286) @@ -940,6 +940,7 @@ /* * Suited for: + * - Foxconn 6150K8MD-8EKRSH: Socket 939 + NVIDIA MCP51 * - MSI K8N Neo4: NVIDIA CK804. TODO: Should probably be K8N Neo4 Platinum, see http://www.coreboot.org/pipermail/flashrom/2010-August/004362.html. * - MSI K8NGM2-L: NVIDIA MCP51 */ @@ -1954,6 +1955,7 @@ {0x10DE, 0x005E, 0x1695, 0x1010, 0x10DE, 0x0050, 0x1695, 0x1010, NULL, NULL, NULL, "EPoX", "EP-8NPA7I", 0, OK, nvidia_mcp_gpio4_raise}, {0x10EC, 0x8139, 0x1695, 0x9001, 0x11C1, 0x5811, 0x1695, 0x9015, NULL, NULL, NULL, "EPoX", "EP-8RDA3+", 0, OK, nvidia_mcp_gpio31_raise}, {0x8086, 0x7110, 0, 0, 0x8086, 0x7190, 0, 0, NULL, "epox", "ep-bx3", "EPoX", "EP-BX3", 0, NT, intel_piix4_gpo22_raise}, + {0x10de, 0x02f0, 0x105b, 0x0d01, 0x10de, 0x0264, 0x105b, 0x0d01, NULL, NULL, NULL, "Foxconn", "6150K8MD-8EKRSH", 0, NT, nvidia_mcp_gpio2_raise}, {0x8086, 0x2443, 0x8086, 0x2442, 0x8086, 0x1130, 0x8086, 0x1130, "^6IEM ", NULL, NULL, "GIGABYTE", "GA-6IEM", 0, NT, intel_ich_gpio25_raise}, {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, {0x8086, 0x244b, 0x8086, 0x2442, 0x8086, 0x2445, 0x1458, 0xa002, NULL, NULL, NULL, "GIGABYTE", "GA-8IRML", 0, OK, intel_ich_gpio25_raise}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Sat Apr 2 13:47:21 2011 (r1285) +++ trunk/print.c Fri Apr 15 01:14:27 2011 (r1286) @@ -462,6 +462,7 @@ B("EPoX", "EP-BX3", 1, "http://www.epox.com/product.asp?ID=EP-BX3", NULL), B("EVGA", "132-CK-NF78", 1, "http://http://www.evga.com/articles/385.asp", NULL), B("FIC", "VA-502", 0, "ftp://ftp.fic.com.tw/motherboard/manual/socket7/va-502/", "No public report found. Owned by Uwe Hermann <uwe(a)hermann-uwe.de>. Seems the PCI subsystem IDs are identical with the Tekram P6Pro-A5. May work now."), + B("Foxconn", "6150K8MD-8EKRSH", 1, "http://www.foxconnchannel.com/product/motherboards/detail_overview.aspx?id=…", NULL), B("Foxconn", "A6VMX", 1, "http://www.foxconnchannel.com/product/motherboards/detail_overview.aspx?id=…", NULL), B("Fujitsu-Siemens", "ESPRIMO P5915", 1, "http://uk.ts.fujitsu.com/rl/servicesupport/techsupport/professionalpc/ESPRI…", "Mainboard model is D2312-A2."), B("GIGABYTE", "GA-2761GXDK", 1, "http://www.computerbase.de/news/hardware/mainboards/amd-systeme/2007/mai/gi…", NULL),

1 0

Fw: FAILED: Abit nf-m2-nView
by Stefan Tauner 13 Apr '11

13 Apr '11

hello guntram! i am glad to hear that it worked. can you please mail us the complete log of sudo flashrom -Vw abit_093.bin -p internal:boardenable=force so that we can verify that and mark this board as tested. thanks! Begin forwarded message: Date: Wed, 13 Apr 2011 11:34:47 +0200 From: Guntram Schmidt <guntram.schmidt(a)googlemail.com> To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Subject: Re: [flashrom] FAILED: Abit nf-m2-nView Hello again! It worked with the "-p internal:boardenable=force" ! So you may regard the mainboard specific code of the Abit nf-m2-nView as tested, now! Thanks a lot, Guntram PS: Unfortunately, the BIOS update didn't solve my problem of CPU-fan not starting...but this may now be a hardware related problem ... Am 13.04.2011 00:32, schrieb Stefan Tauner: > On Tue, 12 Apr 2011 22:14:16 +0200 > Guntram Schmidt<guntram.schmidt(a)googlemail.com> wrote: > >> I first wanted simply to write the saved BIOS again, to be sure, >> everything works fine before flashing the new version of the bios. >> To be honest: I could'nt figure out the meaning concerning the >> "mainboard-specific code", that's why I tried nevertheless. > > hello > > please retry with "-p internal:boardenable=force" added to your > command and report back, thanks. > > disclamer: i read that manpage section the first time 2 minutes > ago. :) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

FAILED: Abit nf-m2-nView
by Guntram Schmidt 12 Apr '11

12 Apr '11

Hi folks, I wanted to reflash the just-before-backupped BIOS with self-compiled Flashform 0.9.3 on Ubuntu Karmic Koala (9.10) 32-Bit, PAE-Kernel 2.6.31-22. This is the message I got: $ sudo flashrom -w abit_093.bin flashrom v0.9.3-r1205 on Linux 2.6.31-22-generic-pae (i686), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "NVIDIA MCP51", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. WARNING: Your mainboard is abit NF-M2 nView, but the mainboard-specific code has not been tested, and thus will not not be executed by default. Depending on your hardware environment, erasing, writing or even probing can fail without running the board specific code. Please see the man page (section PROGRAMMER SPECIFIC INFO, subsection "internal programmer") for details. Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x00000fff: 0x70f ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0000ffff: 0x70f ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x5973f ERASE FAILED! FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! I first wanted simply to write the saved BIOS again, to be sure, everything works fine before flashing the new version of the bios. To be honest: I could'nt figure out the meaning concerning the "mainboard-specific code", that's why I tried nevertheless. Thanks for any hints on how to continue, Guntram

2 2

Flashrom on MSI X58 Pro-E MS-7522 erase failed!
by Антон Кочков 12 Apr '11

12 Apr '11

Good day! http://paste.flashrom.org/view.php?id=476 http://paste.flashrom.org/view.php?id=477 Best regards, Anton Kochkov.

1 1

Fwd: HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

Forwarding the attachment. ---------- Forwarded message ---------- From: Bernard Matthews <philoscience(a)gmail.com> Date: 2011/4/12 Subject: Re: [flashrom] HELP! "...flash chip is in an unknown state" To: Idwer Vollering <vidwer(a)gmail.com> It gets weirder - when redirecting the output to a file, with "sudo flashrom -V -w flashbackup.rom > output.txt", it works fine. I see that: "Chip status register is 00", and: Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set but in output.txt, but when the output goes straight to the xterm, those registers are set, and: "Chip status register is 1c". What follows is a multiscreen manual cut and paste. ============================================================== grml@grml ~ % sudo flashrom -V -w flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1450M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10009 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "BIOSTAR Group" DMI string system-product-name: "TA785G3" DMI string system-version: " " DMI string baseboard-manufacturer: "BIOSTAR Group" DMI string baseboard-product-name: "TA785G3" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... chipset PCI ID is 1002:439d, SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=4, SpiBridgeDisable=1, DropOneClkOnRd=0 GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK ROM strap override is not active OK. This chipset supports the following protocols: LPC,FWH,SPI. No IT87* serial flash segment enabled. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F002BC-T, 256 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 1c Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is set Chip status register: Bit 3 / Block Protect 1 (BP1) is set Chip status register: Bit 2 / Block Protect 0 (BP0) is set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A.RES, 512 KB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x64, id2 0xe6, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xc2, id2 0x13 Some block protection in effect, disabling Missing status register write definition, assuming EWSR is needed Block protection could not be disabled! Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash before programming... Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x00000fff: 0xf9d ERASE FAILED! Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x0000ffff: 0xf8f7 ERASE FAILED! Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x0000ffff: 0xf8f7 ERASE FAILED! Looking at blockwise erase function 3... trying... 0x000000-0x0fffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x000fffff: 0xe05b5 ERASE FAILED! Looking at blockwise erase function 4... trying... 0x000000-0x0fffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x000fffff: 0xe05b5 ERASE FAILED! Looking at blockwise erase function 5... not defined. Looking for another erase function. FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! sudo flashrom -V -w flashbackup.rom 8.37s user 0.07s system 99% cpu 8.468 total grml@grml ~ % sudo flashrom -v flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Verifying flash... VERIFIED. grml@grml ~ % sudo flashrom -V -w flashbackup.rom > output.txt sudo flashrom -V -w flashbackup.rom > output.txt 54.05s user 0.06s system 99% cpu 54.152 total grml@grml ~ % ls -l total 1060 -rw-r--r-- 1 root root 1048576 2011-04-12 17:54 flashbackup.rom -rw-rw-r-- 1 grml grml 28644 2011-04-12 17:56 output.txt grml@grml ~ % sudo flashrom -v flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Verifying flash... VERIFIED. grml@grml ~ % ============================================================== And attached to this email is the file output.txt. Also, I am using the liveCD version of GRML, debian-based. Hope this helps! ----- bernard On Tue, Apr 12, 2011 at 5:52 PM, Bernard Matthews <philoscience(a)gmail.com> wrote: > Since I know it will work now, I will be happy to try and reflash it > per your instructions so we can see what is happening. > > Give me several minutes, and I will email the output to you. > > Thank you again! > > ----- bernard > > On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>> Thank you very, very much for getting in touch with me! >>> >>> I solved the problem before I got your email, but didn't have a chance >>> to email an update yet. >>> >>> On my system, it appears flashrom cannot be run from an Xterm window. >>> If that is in the documentation somewhere, I apologize for missing it. >> >> No, it's not. This sounds weird. >> >>> >>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>> the image currently in the rom matched my backup file, in case I had >>> to reboot. >>> >>> I cannot recall if I did reboot first, or if I had just closed X windows. >>> >>> Using flashrom from a text terminal CLI worked perfectly! I see the >>> new file and date on my boot screen now, and so far no problems. >>> >>> Thank you folks very much for such a wonderful program. >>> >>> ----- bernard >>> >>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>> Hi Help, >>>>> >>>>> I thought I did what was right, but apparently I'm missing something. >>>>> >>>>> System details: >>>>> >>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>> >>>>> Athlon II X3 435. >>>>> >>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>> >>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>> failure that I felt I had reduced to either a processor failure or a >>>>> board failure. >>>>> >>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>> match. >>>>> >>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>> the same. >>>>> >>>>> So below are the results of my attempt to flash the chip :-(. >>>>> >>>>> >>>>> Here's my initial run to check for compatibility with my board (blank >>>>> spaces/lines added for legibility) >>>>> ============================================================== >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> No operations were specified. >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>> >>>> This is your backup file... >>>> >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Reading flash... done. >>>>> >>>>> ============================================================== >>>>> >>>>> At this point, I did a Google search for "Block protection could not >>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>> BE ABLE TO ERASE! >>>>> >>>>> So, I forged ahead: >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>> >>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>> >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>> >>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>> >>>>> ============================================================== >>>>> >>>>> The above lines show that the file that I'm going to write with >>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>> (88GAP901_BST_20110411.BST). >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>> >>>> and this is the new file. >>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>> >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> FAILED! >>>>> ERASE FAILED! >>>>> FAILED! >>>>> Your flash chip is in an unknown state. >>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>> mail flashrom(a)flashrom.org! >>>>> ------------------------------------------------------------------------------- >>>>> DO NOT REBOOT OR POWEROFF! >>>> >>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>> >>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>> >>>>> ============================================================== >>>>> >>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>> a button or pull a wire, I will leave the machine on for a response. >>>>> >>>>> Thank you very much for your help in advance! >>>>> >>>>> ----- bernard >>>>> >>>>> _______________________________________________ >>>>> flashrom mailing list >>>>> flashrom(a)flashrom.org >>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>> >>>> >>> >> >

2 1

Re: [flashrom] HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

Use "reply to all". Thanks. 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: > It gets weirder - when redirecting the output to a file, with "sudo > flashrom -V -w flashbackup.rom > output.txt", it works fine. > > I see that: > > "Chip status register is 00", and: > > Chip status register: Bit 4 / Block Protect 2 (BP2) is not set > Chip status register: Bit 3 / Block Protect 1 (BP1) is not set > Chip status register: Bit 2 / Block Protect 0 (BP0) is not set > > but in output.txt, but when the output goes straight to the xterm, > those registers are set, and: > > "Chip status register is 1c". > > What follows is a multiscreen manual cut and paste. > > ============================================================== > grml@grml ~ % sudo flashrom -V -w flashbackup.rom > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 1450M loops > per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, > 10000 myus = 10009 us, 4 myus = 5 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "BIOSTAR Group" > DMI string system-product-name: "TA785G3" > DMI string system-version: " " > DMI string baseboard-manufacturer: "BIOSTAR Group" > DMI string baseboard-product-name: "TA785G3" > DMI string baseboard-version: " " > DMI string chassis-type: "Desktop" > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... chipset > PCI ID is 1002:439d, SPI base address is at 0xfec10000 > AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 > PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 > SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, > ArbWaitCount=4, SpiBridgeDisable=1, DropOneClkOnRd=0 > GPIO11 used for SPI_DO > GPIO12 used for SPI_DI > GPIO31 used for SPI_HOLD > GPIO32 used for SPI_CS > GPIO47 used for SPI_CLK > ROM strap override is not active > OK. > This chipset supports the following protocols: LPC,FWH,SPI. > No IT87* serial flash segment enabled. > Probing for AMD Am29F010A/B, 128 KB: skipped. > Probing for AMD Am29F002(N)BB, 256 KB: skipped. > Probing for AMD Am29F002(N)BT, 256 KB: skipped. > Probing for AMD Am29F016D, 2048 KB: skipped. > Probing for AMD Am29F040B, 512 KB: skipped. > Probing for AMD Am29F080B, 1024 KB: skipped. > Probing for AMD Am29LV040B, 512 KB: skipped. > Probing for AMD Am29LV081B, 1024 KB: skipped. > Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A29002B, 256 KB: skipped. > Probing for AMIC A29002T, 256 KB: skipped. > Probing for AMIC A29040B, 512 KB: skipped. > Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for ASD AE49F2008, 256 KB: skipped. > Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Atmel AT29C512, 64 KB: skipped. > Probing for Atmel AT29C010A, 128 KB: skipped. > Probing for Atmel AT29C020, 256 KB: skipped. > Probing for Atmel AT29C040A, 512 KB: skipped. > Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT49BV512, 64 KB: skipped. > Probing for Atmel AT49F020, 256 KB: skipped. > Probing for Atmel AT49F002(N), 256 KB: skipped. > Probing for Atmel AT49F002(N)T, 256 KB: skipped. > Probing for EMST F49B002UA, 256 KB: skipped. > Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN29F010, 128 KB: skipped. > Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. > Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. > Probing for Fujitsu MBM29F004BC, 512 KB: skipped. > Probing for Fujitsu MBM29F004TC, 512 KB: skipped. > Probing for Fujitsu MBM29F400BC, 512 KB: skipped. > Probing for Fujitsu MBM29F400TC, 512 KB: skipped. > Probing for Hyundai HY29F002T, 256 KB: skipped. > Probing for Hyundai HY29F002B, 256 KB: skipped. > Probing for Intel 28F001BX-B, 128 KB: skipped. > Probing for Intel 28F001BX-T, 128 KB: skipped. > Probing for Intel 28F002BC-T, 256 KB: skipped. > Probing for Intel 28F004S5, 512 KB: skipped. > Probing for Intel 28F004BV/BE-B, 512 KB: skipped. > Probing for Intel 28F004BV/BE-T, 512 KB: skipped. > Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. > Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. > Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Chip status register is 1c > Chip status register: Status Register Write Disable (SRWD) is not set > Chip status register: Bit 6 is not set > Chip status register: Bit 5 / Block Protect 3 (BP3) is not set > Chip status register: Bit 4 / Block Protect 2 (BP2) is set > Chip status register: Bit 3 / Block Protect 1 (BP1) is set > Chip status register: Bit 2 / Block Protect 0 (BP0) is set > Chip status register: Write Enable Latch (WEL) is not set > Chip status register: Write In Progress (WIP/BUSY) is not set > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX29F001B, 128 KB: skipped. > Probing for Macronix MX29F001T, 128 KB: skipped. > Probing for Macronix MX29F002B, 256 KB: skipped. > Probing for Macronix MX29F002T, 256 KB: skipped. > Probing for Macronix MX29LV040, 512 KB: skipped. > Probing for MoselVitelic V29C51000B, 64 KB: skipped. > Probing for MoselVitelic V29C51000T, 64 KB: skipped. > Probing for MoselVitelic V29C51400B, 512 KB: skipped. > Probing for MoselVitelic V29C51400T, 512 KB: skipped. > Probing for MoselVitelic V29LC51000, 64 KB: skipped. > Probing for MoselVitelic V29LC51001, 128 KB: skipped. > Probing for MoselVitelic V29LC51002, 256 KB: skipped. > Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm29F002T, 256 KB: skipped. > Probing for PMC Pm29F002B, 256 KB: skipped. > Probing for PMC Pm39LV010, 128 KB: skipped. > Probing for PMC Pm39LV020, 256 KB: skipped. > Probing for PMC Pm39LV040, 512 KB: skipped. > Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 > Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for SST SST25LF040A.RES, 512 KB: probe_spi_res2: id1 0x13, id2 0x13 > Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 > Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST28SF040A, 512 KB: skipped. > Probing for SST SST29EE010, 128 KB: skipped. > Probing for SST SST29LE010, 128 KB: skipped. > Probing for SST SST29EE020A, 256 KB: skipped. > Probing for SST SST29LE020, 256 KB: skipped. > Probing for SST SST39SF512, 64 KB: skipped. > Probing for SST SST39SF010A, 128 KB: skipped. > Probing for SST SST39SF020A, 256 KB: skipped. > Probing for SST SST39SF040, 512 KB: skipped. > Probing for SST SST39VF512, 64 KB: skipped. > Probing for SST SST39VF010, 128 KB: skipped. > Probing for SST SST39VF020, 256 KB: skipped. > Probing for SST SST39VF040, 512 KB: skipped. > Probing for SST SST39VF080, 1024 KB: skipped. > Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x64, > id2 0xe6, id1 is normal flash content, id2 is normal flash content > Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. > Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. > Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. > Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M29F002B, 256 KB: skipped. > Probing for ST M29F002T/NT, 256 KB: skipped. > Probing for ST M29F040B, 512 KB: skipped. > Probing for ST M29F400BB, 512 KB: skipped. > Probing for ST M29F400BT, 512 KB: skipped. > Probing for ST M29W010B, 128 KB: skipped. > Probing for ST M29W040B, 512 KB: skipped. > Probing for ST M29W512B, 64 KB: skipped. > Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xc9, id2 0x98, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. > Probing for TI TMS29F002RB, 256 KB: skipped. > Probing for TI TMS29F002RT, 256 KB: skipped. > Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W29C011, 128 KB: skipped. > Probing for Winbond W29C020C, 256 KB: skipped. > Probing for Winbond W29C040P, 512 KB: skipped. > Probing for Winbond W29EE011, 128 KB: skipped. > Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W49F002U, 256 KB: skipped. > Probing for Winbond W49F020, 256 KB: skipped. > Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe > timing information, using default 10mS/40uS. probe_jedec_common: id1 > 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 > is normal flash content > Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct > probe timing information, using default 10mS/40uS. probe_jedec_common: > id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, > id2 is normal flash content > Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for Atmel unknown Atmel SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for Macronix unknown Macronix SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Sanyo unknown Sanyo SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Generic unknown SPI chip (RDID), 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 > 0xc2, id2 0x13 > Some block protection in effect, disabling > Missing status register write definition, assuming EWSR is needed > Block protection could not be disabled! > Flash image seems to be a legacy BIOS. Disabling checks. > Writing flash chip... Erasing flash before programming... Erasing > flash chip... Looking at blockwise erase function 0... trying... > 0x000000-0x000fff, ERASE FAILED at 0x0000000c! Expected=0xff, > Read=0x0c, failed byte count from 0x00000000-0x00000fff: 0xf9d > ERASE FAILED! > > Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x0000ffff: 0xf8f7 > ERASE FAILED! > > Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x0000ffff: 0xf8f7 > ERASE FAILED! > > Looking at blockwise erase function 3... trying... 0x000000-0x0fffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x000fffff: 0xe05b5 > ERASE FAILED! > > Looking at blockwise erase function 4... trying... 0x000000-0x0fffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x000fffff: 0xe05b5 > ERASE FAILED! > > Looking at blockwise erase function 5... not defined. Looking for > another erase function. > FAILED! > ERASE FAILED! > FAILED! > Your flash chip is in an unknown state. > Get help on IRC at irc.freenode.net (channel #flashrom) or > mail flashrom(a)flashrom.org! > ------------------------------------------------------------------------------- > DO NOT REBOOT OR POWEROFF! > sudo flashrom -V -w flashbackup.rom 8.37s user 0.07s system 99% cpu 8.468 total > > grml@grml ~ % sudo flashrom -v flashbackup.rom > > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > No coreboot table found. > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. > This chipset supports the following protocols: LPC,FWH,SPI. > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Flash image seems to be a legacy BIOS. Disabling checks. > Verifying flash... VERIFIED. > > grml@grml ~ % sudo flashrom -V -w flashbackup.rom > output.txt > > sudo flashrom -V -w flashbackup.rom > output.txt 54.05s user 0.06s > system 99% cpu 54.152 total > > grml@grml ~ % ls -l > total 1060 > -rw-r--r-- 1 root root 1048576 2011-04-12 17:54 flashbackup.rom > -rw-rw-r-- 1 grml grml 28644 2011-04-12 17:56 output.txt > > grml@grml ~ % sudo flashrom -v flashbackup.rom > > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > No coreboot table found. > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. > This chipset supports the following protocols: LPC,FWH,SPI. > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Flash image seems to be a legacy BIOS. Disabling checks. > Verifying flash... VERIFIED. > grml@grml ~ % > ============================================================== > > And attached to this email is the file output.txt. > > Also, I am using the liveCD version of GRML, debian-based. > > Hope this helps! > > ----- bernard > > On Tue, Apr 12, 2011 at 5:52 PM, Bernard Matthews > <philoscience(a)gmail.com> wrote: >> Since I know it will work now, I will be happy to try and reflash it >> per your instructions so we can see what is happening. >> >> Give me several minutes, and I will email the output to you. >> >> Thank you again! >> >> ----- bernard >> >> On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>> Thank you very, very much for getting in touch with me! >>>> >>>> I solved the problem before I got your email, but didn't have a chance >>>> to email an update yet. >>>> >>>> On my system, it appears flashrom cannot be run from an Xterm window. >>>> If that is in the documentation somewhere, I apologize for missing it. >>> >>> No, it's not. This sounds weird. >>> >>>> >>>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>>> the image currently in the rom matched my backup file, in case I had >>>> to reboot. >>>> >>>> I cannot recall if I did reboot first, or if I had just closed X windows. >>>> >>>> Using flashrom from a text terminal CLI worked perfectly! I see the >>>> new file and date on my boot screen now, and so far no problems. >>>> >>>> Thank you folks very much for such a wonderful program. >>>> >>>> ----- bernard >>>> >>>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>>> Hi Help, >>>>>> >>>>>> I thought I did what was right, but apparently I'm missing something. >>>>>> >>>>>> System details: >>>>>> >>>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>>> >>>>>> Athlon II X3 435. >>>>>> >>>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>>> >>>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>>> failure that I felt I had reduced to either a processor failure or a >>>>>> board failure. >>>>>> >>>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>>> match. >>>>>> >>>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>>> the same. >>>>>> >>>>>> So below are the results of my attempt to flash the chip :-(. >>>>>> >>>>>> >>>>>> Here's my initial run to check for compatibility with my board (blank >>>>>> spaces/lines added for legibility) >>>>>> ============================================================== >>>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> No operations were specified. >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>>> >>>>> This is your backup file... >>>>> >>>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> Block protection could not be disabled! >>>>>> Reading flash... done. >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> At this point, I did a Google search for "Block protection could not >>>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>>> BE ABLE TO ERASE! >>>>>> >>>>>> So, I forged ahead: >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>>> >>>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>>> >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>>> >>>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> The above lines show that the file that I'm going to write with >>>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>>> (88GAP901_BST_20110411.BST). >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>>> >>>>> and this is the new file. >>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> Block protection could not be disabled! >>>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>>> >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>>> ERASE FAILED! >>>>>> FAILED! >>>>>> ERASE FAILED! >>>>>> FAILED! >>>>>> Your flash chip is in an unknown state. >>>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>>> mail flashrom(a)flashrom.org! >>>>>> ------------------------------------------------------------------------------- >>>>>> DO NOT REBOOT OR POWEROFF! >>>>> >>>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>>> >>>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>>> a button or pull a wire, I will leave the machine on for a response. >>>>>> >>>>>> Thank you very much for your help in advance! >>>>>> >>>>>> ----- bernard >>>>>> >>>>>> _______________________________________________ >>>>>> flashrom mailing list >>>>>> flashrom(a)flashrom.org >>>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>>> >>>>> >>>> >>> >> >

1 0

Re: [flashrom] HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: > Since I know it will work now, I will be happy to try and reflash it > per your instructions so we can see what is happening. > > Give me several minutes, and I will email the output to you. > > Thank you again! Please use "reply to all", thanks. Idwer > > ----- bernard > > On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>> Thank you very, very much for getting in touch with me! >>> >>> I solved the problem before I got your email, but didn't have a chance >>> to email an update yet. >>> >>> On my system, it appears flashrom cannot be run from an Xterm window. >>> If that is in the documentation somewhere, I apologize for missing it. >> >> No, it's not. This sounds weird. >> >>> >>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>> the image currently in the rom matched my backup file, in case I had >>> to reboot. >>> >>> I cannot recall if I did reboot first, or if I had just closed X windows. >>> >>> Using flashrom from a text terminal CLI worked perfectly! I see the >>> new file and date on my boot screen now, and so far no problems. >>> >>> Thank you folks very much for such a wonderful program. >>> >>> ----- bernard >>> >>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>> Hi Help, >>>>> >>>>> I thought I did what was right, but apparently I'm missing something. >>>>> >>>>> System details: >>>>> >>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>> >>>>> Athlon II X3 435. >>>>> >>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>> >>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>> failure that I felt I had reduced to either a processor failure or a >>>>> board failure. >>>>> >>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>> match. >>>>> >>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>> the same. >>>>> >>>>> So below are the results of my attempt to flash the chip :-(. >>>>> >>>>> >>>>> Here's my initial run to check for compatibility with my board (blank >>>>> spaces/lines added for legibility) >>>>> ============================================================== >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> No operations were specified. >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>> >>>> This is your backup file... >>>> >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Reading flash... done. >>>>> >>>>> ============================================================== >>>>> >>>>> At this point, I did a Google search for "Block protection could not >>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>> BE ABLE TO ERASE! >>>>> >>>>> So, I forged ahead: >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>> >>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>> >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>> >>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>> >>>>> ============================================================== >>>>> >>>>> The above lines show that the file that I'm going to write with >>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>> (88GAP901_BST_20110411.BST). >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>> >>>> and this is the new file. >>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>> >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> FAILED! >>>>> ERASE FAILED! >>>>> FAILED! >>>>> Your flash chip is in an unknown state. >>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>> mail flashrom(a)flashrom.org! >>>>> ------------------------------------------------------------------------------- >>>>> DO NOT REBOOT OR POWEROFF! >>>> >>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>> >>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>> >>>>> ============================================================== >>>>> >>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>> a button or pull a wire, I will leave the machine on for a response. >>>>> >>>>> Thank you very much for your help in advance! >>>>> >>>>> ----- bernard >>>>> >>>>> _______________________________________________ >>>>> flashrom mailing list >>>>> flashrom(a)flashrom.org >>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>> >>>> >>> >> >

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom