This is the second mainboard that I try showing a message about
finishing support for the W836xx Super I/O, the first was
http://www.flashrom.org/pipermail/flashrom/2014-June/012651.html
let me know if I can do more to help.
Here is the output of flashrom -Vw for a successful write:
flashrom v0.9.7-r1822 on Linux 3.2.0-4-486 (i586)
flashrom is free software, get the source code at http://www.flashrom.org
flashrom was built with libpci 3.1.9, GCC 4.7.2, little endian
Command line (4 args): flashrom -p
internal:laptop=this_is_not_a_laptop -Vw coreboot.rom
Calibrating delay loop... OS timer resolution is 16 usecs, 23M loops
per second, delay more than 10% too short (got 73% of expected delay),
recalculating... 23M loops per second, delay more than 10% too short
(got 80% of expected delay), recalculating... 23M loops per second,
delay more than 10% too short (got 80% of expected delay),
recalculating... 23M loops per second, delay more than 10% too short
(got 80% of expected delay), recalculating... 23M loops per second,
delay loop is unreliable, trying to continue 10 myus = 23 us, 100 myus
= 82 us, 1000 myus = 746 us, 10000 myus = 16299 us, 64 myus = 59 us,
OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
DMI chassis-type is not specific enough.
DMI string system-manufacturer: "PRAIM"
DMI string system-product-name: "Primo"
DMI string system-version: "04"
DMI string baseboard-manufacturer: "PRAIM"
DMI string baseboard-product-name: "PrimoHw01"
DMI string baseboard-version: "04"
W836xx enter config mode worked or we were already in config mode.
W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: e2.
Please send the output of "flashrom -V -p internal" to
flashrom(a)flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
========================================================================
WARNING! You may be running flashrom on an unsupported laptop. We could
not detect this for sure because your vendor has not setup the SMBIOS
tables correctly. You can enforce execution by adding
'-p internal:laptop=this_is_not_a_laptop' to the command line, but
please read the following warning if you are not sure.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See the manpage and http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
Found chipset "AMD CS5530(A)" with PCI ID 1078:0100. Enabling flash write... OK.
The following protocols are supported: Parallel.
Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0x1f, id2 0x5f
Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Found Atmel flash chip "AT29C010A" (128 kB, Parallel) at physical
address 0xfffe0000.
Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49(H)F010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F040, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F080, 1024 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Atmel AT49F080T, 1024 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for ESMT F49B002UA, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0x1f, id2
0x5f, id1 is normal flash content, id2 is normal flash content
Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0x1f,
id2 0x5f, id1 is normal flash content, id2 is normal flash content
Probing for Eon EN29LV640B, 8192 kB: probe_en29lv640b: id1 0x5f1f, id2 0x001f
Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for Fujitsu MBM29LV160BE, 2048 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for Fujitsu MBM29LV160TE, 2048 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation
Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1
0x5f, id2 0x1f, id1 parity violation, id1 is normal flash content, id2
is normal flash content
Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1
0x5f, id2 0x1f, id1 parity violation
Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1
0x1f, id2 0xd5
Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec_common: id1 0x25,
id2 0xee
Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec_common: id1 0x25,
id2 0xee
Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for PMC Pm39LV512, 64 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation
Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0x5f,
id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0x5f, id2 0x1f
Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation
Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0x5f, id2
0x1f, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB:
Old Winbond W29* probe method disabled because the probing sequence
puts the AMIC A49LF040A in a funky state. Use 'flashrom -c
W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with
such a chip.
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB:
probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common:
id1 0x1f, id2 0xd5
Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W39F010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W39L010, 128 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W39L020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0x1f, id2 0xd5
Found Atmel flash chip "AT29C010A" (128 kB, Parallel).
===
This flash part has status UNTESTED for operations: WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to flashrom(a)flashrom.org if any of the above operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -Vr,
-VE, -Vw), and mention which mainboard or programmer you tested.
Please mention your board in the subject line. Thanks for your help!
coreboot last image size (not ROM size) is 131072 bytes.
Manufacturer: ASI
Mainboard ID: MB-5BLMP
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0...
0x000000-0x01ffff:EW
Erase/write done.
Verifying flash... VERIFIED.
Restoring PCI config space for 00:12:0 reg 0x5b
Restoring PCI config space for 00:12:0 reg 0x52
--
Daniele Forsi
1
0
/# flashrom -p serprog:dev=/dev/ttyUSB0:2000000 -Vw a6.bin
flashrom v0.9.7-r1822 on Linux 3.8.0-29-generic (i686)
flashrom is free software, get the source code at http://www.flashrom.org
flashrom was built with libpci 3.1.8, GCC 4.6.3, little endian
Command line (4 args): flashrom -p serprog:dev=/dev/ttyUSB0:2000000 -Vw a6.bin
Calibrating delay loop... OS timer resolution is 1 usecs, 1146M loops
per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 995 us,
10000 myus = 9989 us, 4 myus = 6 us, OK.
Initializing serprog programmer
Baud rate is 2000000 now.
serprog: connected - attempting to synchronize
..
serprog: Synchronized
serprog: Interface version ok.
serprog: Bus support: parallel=off, LPC=off, FWH=off, SPI=on
Warning: Automatic command availability check failed for cmd 0x08 -
won't execute cmd
Warning: Automatic command availability check failed for cmd 0x11 -
won't execute cmd
serprog: Programmer name is "serprog-duino"
serprog: Serial buffer size is 65535
serprog: Warning: Programmer does not support toggling its output drivers
The following protocols are supported: SPI.
Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L80P, 1024 kB: RDID byte 0 parity violation.
probe_spi_rdid_generic: id1 0xff, id2 0xffff
Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DL081, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DL161, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT25F512, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff
Probing for Atmel AT25F512A, 64 kB: probe_spi_at25f: id1 0xff, id2 0xff
Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Atmel AT25F1024(A), 128 kB: probe_spi_at25f: id1 0x00, id2 0x00
Probing for Atmel AT25F2048, 256 kB: probe_spi_at25f: id1 0x00, id2 0x00
Probing for Atmel AT25F4096, 512 kB: probe_spi_at25f: id1 0x00, id2 0x00
Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB321E, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for ESMT F25L32PA, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Found Eon flash chip "EN25QH128" (16384 kB, SPI) on serprog.
Chip status register is 0x90.
Chip status register: Status Register Write Disable (SRWD, SRP, ...) is set
Chip status register: Bit 6 is not set
Chip status register: Block Protect 3 (BP3) is not set
Chip status register: Block Protect 2 (BP2) is set
Chip status register: Block Protect 1 (BP1) is not set
Chip status register: Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0xe600
Probing for GigaDevice GD25Q64(B), 8192 kB: RDID byte 0 parity
violation. probe_spi_rdid_generic: id1 0xff, id2 0xffff
Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX23L3254, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L2005(C), 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L4005(A/C), 512 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix MX25L8005/MX25V8005, 1024 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L1605A/MX25L1606E, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L1605D/MX25L1608D/MX25L1673E, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L3206E, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L3273E, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25L6405(D), 8192 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix MX25L6406E/MX25L6436E, 8192 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L6445E/MX25L6473E, 8192 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Macronix MX25L12805(D), 16384 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID.
Probing for Micron/Numonyx/ST M25P10-A, 128 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID.
Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in
favour of RDID.
Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in
favour of RDID.
Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25P128, 16384 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PE80, 1024 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PE16, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PX80, 1024 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PX16, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PX32, 4096 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M25PX64, 8192 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M45PE80, 1024 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST M45PE16, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q016, 2048 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for PMC Pm25LV512(A), 64 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for PMC Pm25LV010, 128 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Sanyo LE25FW106, 128 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Sanyo LE25FW406A, 512 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Sanyo LE25FU406B, 512 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Sanyo LE25FW418A, 512 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Sanyo LE25FW806, 1024 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Sanyo LE25FW808, 1024 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL116K/S25FL216K, 2048 kB: RDID byte 0 parity
violation. probe_spi_rdid_generic: id1 0x00, id2 0x00
Probing for Spansion S25FL132K, 4096 kB: RDID byte 0 parity violation.
probe_spi_rdid_generic: id1 0xff, id2 0xfff3
Probing for Spansion S25FL164K, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Spansion S25FL128S......0, 16384 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for SST SST25LF020A, 256 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for SST SST25LF080(A), 1024 kB: probe_spi_res2: id1 0x17, id2 0x17
Probing for SST SST25VF512A, 64 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25VF020, 256 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25VF020B, 256 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0x1c, id2 0x17
Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for SST SST25WF080, 1024 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x1c,
id2 0x7018
Probing for Unknown SFDP-capable chip, 0 kB: Parsing JEDEC flash
parameter table... done.
Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Atmel unknown Atmel SPI chip, 0 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for Macronix unknown Macronix SPI chip, 0 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic:
id1 0x1c, id2 0x7018
Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1
0x1c, id2 0x7018
Probing for Sanyo unknown Sanyo SPI chip, 0 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Generic unknown SPI chip (RDID), 0 kB:
probe_spi_rdid_generic: id1 0x1c, id2 0x7018
Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1
0x1c, id2 0x17
Found Eon flash chip "EN25QH128" (16384 kB, SPI).
This chip may contain one-time programmable memory. flashrom cannot read
and may never be able to write it, hence it may not be able to completely
clone the contents of this chip (see man page for details).
===
This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to flashrom(a)flashrom.org if any of the above operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -Vr,
-VE, -Vw), and mention which mainboard or programmer you tested.
Please mention your board in the subject line. Thanks for your help!
Some block protection in effect, disabling...
Need to disable the register lock first... done.
disabled.
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0...
0x000000-0x000fff:EW, 0x001000-0x001fff:W, 0x002000-0x002fff:EW,
0x003000-0x003fff:EW, 0x004000-0x004fff:EW, 0x005000-0x005fff:EW,
0x006000-0x006fff:EW, 0x007000-0x007fff:W, 0x008000-0x008fff:W,
0x009000-0x009fff:EFAILED at 0x00009996! Expected=0xff, Found=0x1f,
failed byte count from 0x00009000-0x00009fff: 0x320
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 1... 0x000000-0x00ffff:EFAILED at 0x000012db!
Expected=0xff, Found=0x18, failed byte count from
0x00000000-0x0000ffff: 0x70c4
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 2... 0x000000-0xffffff:EFAILED at 0x00000000!
Expected=0xff, Found=0x00, failed byte count from
0x00000000-0x00ffffff: 0x6f43f3
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 3... 0x000000-0xffffff:EFAILED at 0x00001bc3!
Expected=0xff, Found=0x03, failed byte count from
0x00000000-0x00ffffff: 0x6c7627
ERASE FAILED!
Looking for another erase function.
No usable erase functions left.
FAILED!
Uh oh. Erase/write failed. Checking if anything has changed.
Reading current flash chip contents... done.
Apparently at least some data has changed.
Your flash chip is in an unknown state.
Please report this on IRC at chat.freenode.net (channel #flashrom) or
mail flashrom(a)flashrom.org, thanks!
1
0
Hi.
I've seen a number of patches that tried to add 4-byte addressed chips support to flashrom,
but none of them seem to work on Winbond W25Q256FV (even provided the support for the
chip is added with only full-chip erasers declared).
Are there any plans on adding 4-byte addressed chips support into flashrom?
I'm planning to work on that on my own, taking Mark Marshall's and Brian Rak's patches as a base:
http://www.flashrom.org/pipermail/flashrom/2013-March/010759.html
https://gist.github.com/devicenull/8735650
However if there is any ongoing activity on this topic and anyone has further (possibly incomplete) patches, please share
as I couldn't find them.
With best regards -
Alexander Amelkin
1
0
Hey,
i've just played around with your software, and so far i'm pretty excited :)
i couldn't get the GUI to compile, but the console version works fine :)
i use it on a raspberry pi but i can't read from a chip i have on hand
here...
Because i need to preserve the data on the chip, i can't test writing right
now,
but i hope you can help me though :)
Attatched you'll find a picture of the EEPROM, and the log file - but i
doubt you can get anything useful from it, at least i couldn't :D
I really hope you can help me with this - i struggle with this thing for
days now x)
Regards,
Markus :)
1
0
30 Jun '14
On Wed, 3 Oct 2012 06:13:00 +0200
Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> wrote:
> This patch set enables us to figure out if transactions will succeed
> without executing them, which allows for a refactoring of
> probe_spi_rdid_generic() which in consequence makes it possible to add
> probe_spi_rdid_edi().
>
Hi Stefan,
was there any development towards the functionality discussed
in this old thread: check_trans() and probe_spi_rdid_edi()?
> The infrastructure code as a whole, but especially the ichspi code
> is heavily modified. Please be aware of that if you test it on
> mainboards.
>
> Antonio: please rebase your Spansion patch on this one and extend it
> to add actually two chips by using the full 32 bit model IDs
> (0x20184d00, 0x20184d01) and .probe = probe_spi_rdid_edi.
>
I am playing with these chips again.
FTR I am able to read and write S25FL129P1 chips using flashrom
v0.9.7-r1782 which is in Debian ubstable, it supports the similar
"S25FL128S......0", but only the bulk erase function worked
(spi_block_erase_60), I wasn't able to do a block or sector erase; can
this depend on the programmer (ft2232_spi)?
I will send a proper log the next time I write a chip.
I have also tried to rebase this old set about check_trans() and
probe_spi_rdid_edi() on top of the latest svn, I will check if the code
still works but I wanted to ask first what the current status
is, and if there is still interest to support rdid EDI.
Thanks,
Antonio
--
Antonio Ospite
http://ao2.it
A: Because it messes up the order in which people normally read text.
See http://en.wikipedia.org/wiki/Posting_style
Q: Why is top-posting such a bad thing?
1
2
flashrom asked me to send you this output, so I did. Hope it helps.
/Martin
flashrom v0.9.7-r1782 on Linux 3.14-1-amd64 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org
flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian
Command line (3 args): flashrom -p internal -V
Calibrating delay loop... OS timer resolution is 1 usecs, 3313M loops per
second, 10 myus = 10 us, 100 myus = 118 us, 1000 myus = 997 us, 10000 myus =
9897 us, 4 myus = 15 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
W836xx enter config mode worked or we were already in config mode. W836xx leave
config mode had no effect.
Active config mode, unknown reg 0x20 ID: 00.
Please send the output of "flashrom -V" to
flashrom(a)flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
Found chipset "Intel QM87" with PCI ID 8086:8c4f.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom(a)flashrom.org including a verbose (-V)
log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap : not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytesSPI Read Configuration: prefetching
enabled, caching enabled,
BIOS_CNTL = 0x2b: BIOS Lock Enable: enabled, BIOS Write Enable: enabled
Warning: BIOS region SMM protection is enabled!
Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed.
New value is 0x2b.
SPIBAR = 0x00007f85a7697000 + 0x3800
0x04: 0xf008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x50: 0x00004a4b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x4a, BRRA 0x4b
0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff)
is read-only.
0x58: 0x0bff0500 FREG1: BIOS region (0x00500000-0x00bfffff) is read-write.
0x5C: 0x04ff0003 FREG2: Warning: Management Engine region
(0x00003000-0x004fffff) is locked.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is
read-write.
Not all flash regions are freely accessible by flashrom. This is most likely
due to an active ME. Please see http://flashrom.org/ME for details.
0x78: 0x8bff0b40 PR1: Warning: 0x00b40000-0x00bfffff is read-only.
0x7C: 0x8adf0ab1 PR2: Warning: 0x00ab1000-0x00adffff is read-only.
0x80: 0x8ab00ab0 PR3: Warning: 0x00ab0000-0x00ab0fff is read-only.
0x84: 0x8aaf0800 PR4: Warning: 0x00800000-0x00aaffff is read-only.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0xc0 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf94000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=1
0x94: 0x0606 (PREOP)
0x96: 0x3f90 (OPTYPE)
0x98: 0x03013505 (OPMENU)
0x9C: 0x9f20d802 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80802025 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x80002025 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0
0xD0: 0x00f12005 (FPB)
Enabling hardware sequencing due to multiple flash chips detected.
Density of ICH SPI component with index 1 is invalid. Encoded density is 0x6.
OK.
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip
with a density of 8192 kB.
The flash address space (0x000000 - 0x7fffff) is divided at address 0x005000 in
two partitions.
The first partition ranges from 0x000000 to 0x004fff.
In that range are 5 erase blocks with 4096 B each.
The second partition ranges from 0x005000 to 0x7fffff.
In that range are 2043 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific)
at physical address 0x0.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x00, id2 0x00, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x80, id2 0x03, id1
is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x83, id2 0xc4,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x3b, id2 0x04,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported
size 1024 kB of chipset/board/programmer for FWH interface,
probe/read/erase/write may fail. probe_82802ab: id1 0x70, id2 0xf2, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported
size 1024 kB of chipset/board/programmer for FWH interface,
probe/read/erase/write may fail. probe_82802ab: id1 0x70, id2 0xf2, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x3b, id2 0x04,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x80,
id2 0x03, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific).
No operations were specified.
Restoring MMIO space at 0x7f85a769a8a0
Restoring PCI config space for 00:1f:0 reg 0xdc
1
0
flashrom v0.9.7-r1711 on Linux 3.14.6-1-ARCH (i686)
flashrom is free software, get the source code at http://www.flashrom.org
flashrom was built with libpci 3.2.0, GCC 4.8.2, little endian
Command line (3 args): flashrom -V -p internal
Calibrating delay loop... OS timer resolution is 2 usecs, 893M loops per second, delay more than 10% too short (got 85% of expected delay), recalculating... 910M loops per second, delay more than 10% too short (got 87% of expected delay), recalculating... 909M loops per second, delay more than 10% too short (got 86% of expected delay), recalculating... 909M loops per second, delay more than 10% too short (got 86% of expected delay), recalculating... 910M loops per second, delay loop is unreliable, trying to continue 10 myus = 9 us, 100 myus = 86 us, 1000 myus = 856 us, 10000 myus = 10078 us, 8 myus = 8 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "Hewlett-Packard"
DMI string system-product-name: "HP Pavilion dv1000 (PW923EA#ABZ) "
DMI string system-version: "Rev 1 "
DMI string baseboard-manufacturer: "Quanta"
DMI string baseboard-product-name: "09B8"
DMI string baseboard-version: "34.20"
DMI string chassis-type: "Notebook"
Laptop detected via DMI.
W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: ec.
Please send the output of "flashrom -V" to
flashrom(a)flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
========================================================================
WARNING! You seem to be running flashrom on an unsupported laptop.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See the manpage and http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Aborting.
Error: Programmer initialization failed.
1
0
I have it loaded on a flash drive along with doslfn (Dos long file name)
so that it doesn't error out with a file not found when it tries to
access DMIDECODE (which with 8.3 convention is DMIDEC~1).
First two boards that I ran this configuration on (with the jumper
closed since these are HP XW9400) backed up the existing ROM without any
problem and then flashed to one with the current boot block as it was
supposed to.
Third board, backed up the existing BIOS and then completed the reflash
with verify and immediately after passing verification threw the error.
This board is now bricked.
Fourth board throws the error immediately after doing a backup of the
flash or even a simple probe. This one I haven't flashed, so it didn't
brick.
So I tried to do a rom backup and probe with one of the first 2 boards
since those passed without any problem, but it also now throws the
error.
It's not memory or processor since I'm using known good components.
>>> Stefan Tauner 06/25/14 3:23 AM >>>
On Tue, 24 Jun 2014 22:31:15 -0400
"John Pohlman" wrote:
> I've got a strange one here flashing an HP XW9400
>
> flashrom 0.9.6 running on FreeDos worked perfectly for reading and
writing a bios but now it throws this error on exit along with an EIP
error.
>
> The problem occurs on multiple boards even when doing something as
simple as writing a bios dump.
>
> Anyone have any ideas?
Hi,
what does "now" mean? Did the flashrom version change, or anything
else? Can you please post a log or at least an excerpt of one?
--
Kind regards/Mit freundlichen Grüßen, Stefan Tauner
1
0
I've got a strange one here flashing an HP XW9400
flashrom 0.9.6 running on FreeDos worked perfectly for reading and writing a bios but now it throws this error on exit along with an EIP error.
The problem occurs on multiple boards even when doing something as simple as writing a bios dump.
Anyone have any ideas?
2
1
Hi,
I updated Nico's patch[1] for IFD parsing support in flashrom to apply
to the current tree. Just want to put it out there to avoid duplicate work.
Regards,
Patrick
[1] http://patchwork.coreboot.org/patch/3966/
--
Patrick Georgi
Fachbereich SINA-Entwicklung
Public Sector
secunet Security Networks AG
Tel.: +49 201 54 54-3610, Fax: +49 201 54 54-1325
E-Mail: Patrick.Georgi(a)secunet.com
Mergenthalerallee 77, 65760 Eschborn, Deutschland
www.secunet.com
Sitz: Kronprinzenstraße 30, 45128 Essen, Deutschland / Amtsgericht Essen
HRB 13615
Vorstand: Dr. Rainer Baumgart (Vors.), Willem Bulthuis, Thomas Pleines
Aufsichtsratsvorsitzender: Dr. Peter Zattler
1
0
On Sun, 22 Jun 2014 21:05:25 -0400
Nicholas Hadler <nicholas.hadler(a)gmail.com> wrote:
> Hi, sorry if this is a dumb question but is there anyway to flash a M24C32
> with flashrom?
No. That's an I2C EEPROM and hence is currently not supported.
--
Kind regards/Mit freundlichen Grüßen, Stefan Tauner
1
0
Here is a link to it if it helps:
http://www.mouser.com/ProductDetail/STMicroelectronics/M24C32-WBN6P/?qs=sGA…
On Sun, Jun 22, 2014 at 9:05 PM, Nicholas Hadler <nicholas.hadler(a)gmail.com>
wrote:
> Hi, sorry if this is a dumb question but is there anyway to flash a M24C32
> with flashrom?
>
> Nicholas
>
1
0
Hi, sorry if this is a dumb question but is there anyway to flash a M24C32
with flashrom?
Nicholas
1
0
Re: [flashrom] [PATCH] Add Intel Bay Trail, Rangeley/Avoton and Wildcat Point support.
by Stefan Tauner 21 Jun '14
by Stefan Tauner 21 Jun '14
21 Jun '14
On Sun, 22 Jun 2014 01:46:05 +0200
Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> wrote:
> @@ -612,7 +612,8 @@ static void ich_set_bbar(uint32_t min_addr)
> bbar_off = 0x50;
> break;
> case CHIPSET_ICH8:
> - msg_perr("BBAR offset is unknown on ICH8!\n");
> + case CHIPSET_BAYTRAIL:
> + msg_pdbg("BBAR offset is unknown on ICH8!\n");
^^^^
Fixed locally.
This patch requires some rewording of the manpage explaining IDSEL.
--
Kind regards/Mit freundlichen Grüßen, Stefan Tauner
1
0
Here's a patch for the spi controllers in Intel's Baytrail &
Rangeley/Avoton parts.
This core of this patch originally came from the chromium flashrom repo
and was modified by Sage to support the Rangeley/Avoton parts as well.
Martin
2
2
19 Jun '14
Am 16.06.2014 02:50 schrieb Stefan Tauner:
> Some important facts:
> - AT45 prober issues a 0xD7 opcode (without address) unconditionally.
> - No prober weights yet - any chip matched by a single prober is
> presented to the user.
>
> Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
> ---
> 82802ab.c | 49 +-
> Makefile | 2 +-
> at45db.c | 48 +-
> chipdrivers.h | 36 +-
> cli_classic.c | 132 ++-
> en29lv640b.c | 27 +-
> flash.h | 54 +-
> flashchips.c | 3624 +++++++++++++++++++++++++++++++++------------------------
> flashchips.h | 888 +++++++-------
I tried to verify your conversion of flashchips.c by doing it myself.
Our results differ, though. The differences need to be verified against
the code and the datasheets. I do believe my versions are correct and I
checked most of them against the current code and/or a datasheet, but I
might have made some mistakes.
The differences between your flashchips.c conversion and my conversion are:
probe_spi_at25f is len=2 in my tree, len=3 in yours
probe_82802ab for ATMEL_AT49LH002 is len=2 in my tree, len=3 in yours
probe_jedec for EON_EN29F010 is len=3 in my tree, len=2 in yours
probe_jedec for EON_EN29F002T is len=4 in my tree, len=2 in yours
probe_m29f400bt for FUJITSU_MBM29F400BC is len=2 in my tree, len=3 in yours
probe_m29f400bt for FUJITSU_MBM29F400TC is len=2 in my tree, len=3 in yours
probe_m29f400bt for FUJITSU_MBM29LV160BE is len=2 in my tree, len=3 in yours
probe_m29f400bt for FUJITSU_MBM29LV160TE is len=2 in my tree, len=3 in yours
probe_82802ab for INTEL_28F002T has len=2 in my tree, len=3 in yours
probe_82802ab_* always has len=3 in your tree, and I believe this to be
a systematic error
probe_spi_rems for
SST_SST25VF512A_REMS/SST_SST25VF010_REMS/SST_SST25VF020_REMS/SST_SST25VF040_REMS/SST_SST25VF040B_REMS
is len=2 in my tree, len=3 in yours
probe_jedec for
SST_SST29EE010/SST_SST29LE010/SST_SST29EE020A/SST_SST29LE020 is len=2 in
my tree; len=3 in yours
probe_m29f400bt for ST_M29F400BB is len=2 in my tree, len=3 in yours
probe_jedec for WINBOND_W29C010 has len=2 in my tree, len=3 in yours
probe_jedec for WINBOND_W29C020/WINBOND_W29C040 has len=2 in my tree,
len=3 in yours
This patch has almost the same layout in flashchips.c as your end result
of the probe conversion, the only differences (besides the stuff
mentioned above) are:
Your patch has a struct field .probers, mine doesn't have it to make
sure only flash.h and flashchips.c have to change at the first step
while having virtually identical layout for the new flashchips.c contents.
Your patch has killed probe_timing, mine doesn't yet, that one needs to
die and/or be moved for chips where it is relevant.
Your patch removes all those generic chips, mine doesn't yet, those
things are abominations and need to die.
Your patch treats the at45 chips as two models per hardware to handle
the different sector/page sizes (good thing, I unfortunately didn't get
around to that yet).
I have left feature_bits untouched.
Whitespace has changed for ca. 5 lines as well.
This patch compiles, and although flashchips.c almost looks like your
variant, it needs no code changes outside flashchips.c and flash.h. The
idea behind such a conversion was to decouple layout changes from
semantic changes and do that with copious amounts of anonymous structs.
I did _not_ do this to discredit your work, I simply wanted an easy way
to almost recreate your flashchips.c for verification while not having
to touch any code outside it.
By the way, I'd like to propose a slight change to your struct prober:
Make the individual members of struct probe_res non-nested members of
struct prober, i.e. this
{probe_jedec, {2, {AMD_ID, AMD_AM29F002BB} } },
becomes this
{probe_jedec, 2, {AMD_ID, AMD_AM29F002BB} },
IMHO the second variant looks better.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Index: flashrom-proberewrite/flash.h
===================================================================
--- flashrom-proberewrite/flash.h (Revision 1822)
+++ flashrom-proberewrite/flash.h (Arbeitskopie)
@@ -150,14 +150,6 @@
enum chipbustype bustype;
- /*
- * With 32bit manufacture_id and model_id we can cover IDs up to
- * (including) the 4th bank of JEDEC JEP106W Standard Manufacturer's
- * Identification code.
- */
- uint32_t manufacture_id;
- uint32_t model_id;
-
/* Total chip size in kilobytes */
unsigned int total_size;
/* Chip page size in bytes */
@@ -172,8 +164,23 @@
enum test_state write;
} tested;
- int (*probe) (struct flashctx *flash);
+ struct {
+ int (*probe) (struct flashctx *flash);
+ struct {
+ uint8_t probe_res_len;
+ struct {
+ /*
+ * With 32bit manufacture_id and model_id we can cover IDs up to
+ * (including) the 4th bank of JEDEC JEP106W Standard Manufacturer's
+ * Identification code.
+ */
+ uint32_t manufacture_id;
+ uint32_t model_id;
+ };
+ };
+ };
+
/* Delay after "enter/exit ID mode" commands in microseconds.
* NB: negative values have special meanings, see TIMING_* below.
*/
Index: flashrom-proberewrite/flashchips.c
===================================================================
--- flashrom-proberewrite/flashchips.c (Revision 1822)
+++ flashrom-proberewrite/flashchips.c (Arbeitskopie)
@@ -25,6 +25,7 @@
#include "flash.h"
#include "flashchips.h"
#include "chipdrivers.h"
+#define FIXME 0
/**
* List of supported flash chips.
@@ -61,13 +62,11 @@
.vendor = "AMD",
.name = "Am29F010A/B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F010B, /* Same as Am29F010A */
.total_size = 128,
.page_size = 16 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F010B /* Same as Am29F010A */} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -88,13 +87,11 @@
.vendor = "AMD",
.name = "Am29F002(N)BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F002BB,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_SHORT_RESET | FEATURE_ADDR_2AA,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F002BB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -120,13 +117,11 @@
.vendor = "AMD",
.name = "Am29F002(N)BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F002BT,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_EITHER_RESET | FEATURE_ADDR_2AA,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F002BT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -152,13 +147,11 @@
.vendor = "AMD",
.name = "Am29F016D",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F016D,
.total_size = 2 * 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F016D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -179,13 +172,11 @@
.vendor = "AMD",
.name = "Am29F040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F040B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -206,13 +197,11 @@
.vendor = "AMD",
.name = "Am29F080B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F080B,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29F080B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -233,13 +222,11 @@
.vendor = "AMD",
.name = "Am29LV001BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV001BB,
.total_size = 128,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV001BB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -264,13 +251,11 @@
.vendor = "AMD",
.name = "Am29LV001BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV001BT,
.total_size = 128,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV001BT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -295,13 +280,11 @@
.vendor = "AMD",
.name = "Am29LV002BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV002BB,
.total_size = 256,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV002BB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -327,13 +310,11 @@
.vendor = "AMD",
.name = "Am29LV002BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV002BT,
.total_size = 256,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV002BT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -359,13 +340,11 @@
.vendor = "AMD",
.name = "Am29LV004BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV004BB,
.total_size = 512,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV004BB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -391,13 +370,11 @@
.vendor = "AMD",
.name = "Am29LV004BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV004BT,
.total_size = 512,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV004BT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -423,13 +400,11 @@
.vendor = "AMD",
.name = "Am29LV008BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV008BB,
.total_size = 1024,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV008BB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -455,13 +430,11 @@
.vendor = "AMD",
.name = "Am29LV008BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV008BT,
.total_size = 1024,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV008BT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -487,13 +460,11 @@
.vendor = "AMD",
.name = "Am29LV040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV040B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -514,13 +485,11 @@
.vendor = "AMD",
.name = "Am29LV081B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV080B,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET, /* datasheet specifies address as don't care */
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMD_ID, AMD_AM29LV080B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -541,13 +510,11 @@
.vendor = "AMIC",
.name = "A25L05PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L05PT,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L05PT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -575,13 +542,11 @@
.vendor = "AMIC",
.name = "A25L05PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L05PU,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L05PU} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -609,13 +574,11 @@
.vendor = "AMIC",
.name = "A25L10PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L10PT,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L10PT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -644,13 +607,11 @@
.vendor = "AMIC",
.name = "A25L10PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L10PU,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L10PU} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -679,13 +640,11 @@
.vendor = "AMIC",
.name = "A25L20PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L20PT,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L20PT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -714,13 +673,11 @@
.vendor = "AMIC",
.name = "A25L20PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L20PU,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L20PU} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -754,13 +711,11 @@
.vendor = "AMIC",
.name = "A25L40PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L40PT,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L40PT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -789,13 +744,11 @@
.vendor = "AMIC",
.name = "A25L40PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L40PU,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L40PU} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -824,13 +777,11 @@
.vendor = "AMIC",
.name = "A25L80P",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L80P,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L80P} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -859,13 +810,11 @@
.vendor = "AMIC",
.name = "A25L16PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L16PT,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L16PT} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -897,13 +846,11 @@
.vendor = "AMIC",
.name = "A25L16PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L16PU,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, AMIC_A25L16PU} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -935,13 +882,11 @@
.vendor = "AMIC",
.name = "A25L512",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L512} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -967,13 +912,11 @@
.vendor = "AMIC",
.name = "A25L010",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L010} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -999,13 +942,11 @@
.vendor = "AMIC",
.name = "A25L020",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L020} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1031,13 +972,11 @@
.vendor = "AMIC",
.name = "A25L040",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1063,13 +1002,11 @@
.vendor = "AMIC",
.name = "A25L080",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L080,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L080} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1095,13 +1032,11 @@
.vendor = "AMIC",
.name = "A25L016",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L016,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L016} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1127,14 +1062,12 @@
.vendor = "AMIC",
.name = "A25L032",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L032,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25L032} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1166,15 +1099,13 @@
.vendor = "AMIC",
.name = "A25LQ16",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ16,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25LQ16} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -1205,15 +1136,13 @@
.vendor = "AMIC",
.name = "A25LQ032/A25LQ32A",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ032,
.total_size = 4096,
.page_size = 256,
/* A25LQ32A supports SFDP */
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25LQ032} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1245,8 +1174,6 @@
.vendor = "AMIC",
.name = "A25LQ64",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ032,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
@@ -1254,7 +1181,7 @@
/* QPI enable 0x35, disable 0xF5 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {AMIC_ID_NOPREFIX, AMIC_A25LQ032} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1286,13 +1213,11 @@
.vendor = "AMIC",
.name = "A29002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29002B,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMIC_ID_NOPREFIX, AMIC_A29002B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1318,13 +1243,11 @@
.vendor = "AMIC",
.name = "A29002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMIC_ID_NOPREFIX, AMIC_A29002T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1350,13 +1273,11 @@
.vendor = "AMIC",
.name = "A29040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMIC_ID_NOPREFIX, AMIC_A29040B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1377,13 +1298,11 @@
.vendor = "AMIC",
.name = "A49LF040A",
.bustype = BUS_LPC,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A49LF040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {AMIC_ID_NOPREFIX, AMIC_A49LF040A} } },
.probe_timing = TIMING_ZERO, /* routine is wrapper to probe_jedec (pm49fl00x.c) */
.block_erasers =
{
@@ -1405,14 +1324,12 @@
.vendor = "Atmel",
.name = "AT25DF021",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF021,
.total_size = 256,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF021} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1444,13 +1361,11 @@
.vendor = "Atmel",
.name = "AT25DF041A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF041A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF041A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1482,13 +1397,11 @@
.vendor = "Atmel",
.name = "AT25DF081",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF081} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1520,13 +1433,11 @@
.vendor = "Atmel",
.name = "AT25DF081A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF081A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1558,13 +1469,11 @@
.vendor = "Atmel",
.name = "AT25DF161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF161,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF161} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1596,13 +1505,11 @@
.vendor = "Atmel",
.name = "AT25DF321",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF321,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF321} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1634,14 +1541,12 @@
.vendor = "Atmel",
.name = "AT25DF321A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF321A,
.total_size = 4096,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF321A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1673,13 +1578,11 @@
.vendor = "Atmel",
.name = "AT25DF641(A)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF641,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF641} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1711,14 +1614,12 @@
.vendor = "Atmel",
.name = "AT25DL081",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081,
.total_size = 1024,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DF081} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1750,14 +1651,12 @@
.vendor = "Atmel",
.name = "AT25DL161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DL161,
.total_size = 2048,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DL161} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1789,14 +1688,12 @@
.vendor = "Atmel",
.name = "AT25DQ161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DQ161,
.total_size = 2048,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25DQ161} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1828,13 +1725,11 @@
.vendor = "Atmel",
.name = "AT25F512",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ {probe_spi_at25f, {2, {ATMEL_ID, ATMEL_AT25F512} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1857,13 +1752,11 @@
.vendor = "Atmel",
.name = "AT25F512A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512A,
.total_size = 64,
.page_size = 128,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ {probe_spi_at25f, {2, {ATMEL_ID, ATMEL_AT25F512A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1887,14 +1780,12 @@
.vendor = "Atmel",
.name = "AT25F512B",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512B,
.total_size = 64,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25F512B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1931,13 +1822,11 @@
* All other properties seem to be the same.*/
.name = "AT25F1024(A)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F1024,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ {probe_spi_at25f, {2, {ATMEL_ID, ATMEL_AT25F1024} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1960,13 +1849,11 @@
.vendor = "Atmel",
.name = "AT25F2048",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F2048,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at25f,
+ {probe_spi_at25f, {2, {ATMEL_ID, ATMEL_AT25F2048} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -1989,13 +1876,11 @@
.vendor = "Atmel",
.name = "AT25F4096",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F4096,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at25f,
+ {probe_spi_at25f, {2, {ATMEL_ID, ATMEL_AT25F4096} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2019,13 +1904,11 @@
.vendor = "Atmel",
.name = "AT25FS010",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25FS010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25FS010} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2060,13 +1943,11 @@
.vendor = "Atmel",
.name = "AT25FS040",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25FS040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT25FS040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2098,13 +1979,11 @@
.vendor = "Atmel",
.name = "AT26DF041",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF041,
.total_size = 512,
.page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26DF041} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2130,13 +2009,11 @@
.vendor = "Atmel",
.name = "AT26DF081A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF081A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26DF081A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2168,13 +2045,11 @@
.vendor = "Atmel",
.name = "AT26DF161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF161,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26DF161} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2206,13 +2081,11 @@
.vendor = "Atmel",
.name = "AT26DF161A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF161A,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26DF161A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2245,13 +2118,11 @@
.vendor = "Atmel",
.name = "AT26DF321",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF321,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26DF321} } },
.probe_timing = TIMING_ZERO,
.printlock = spi_prettyprint_status_register_at26df081a,
.unlock = spi_disable_blockprotect,
@@ -2263,13 +2134,11 @@
.vendor = "Atmel",
.name = "AT26F004",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26F004,
.total_size = 512,
.page_size = 256,
- .tested = {.probe = NT, .read = NT, .erase = NT, .write = BAD },
.feature_bits = FEATURE_WRSR_WREN,
- .probe = probe_spi_rdid,
+ .tested = {.probe = NT, .read = NT, .erase = NT, .write = BAD },
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT26F004} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2300,13 +2169,11 @@
.vendor = "Atmel",
.name = "AT29C512",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C512,
.total_size = 64,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT29C512} } },
.probe_timing = 10000, /* 10mS, Enter=Exec */
.block_erasers =
{
@@ -2324,13 +2191,11 @@
.vendor = "Atmel",
.name = "AT29C010A",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C010A,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT29C010A} } },
.probe_timing = 10000, /* 10mS, Enter=Exec */
.block_erasers =
{
@@ -2348,13 +2213,11 @@
.vendor = "Atmel",
.name = "AT29C020",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT29C020} } },
.probe_timing = 10000, /* 10ms */
.block_erasers =
{
@@ -2372,13 +2235,11 @@
.vendor = "Atmel",
.name = "AT29C040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C040A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT29C040A} } },
.probe_timing = 10000, /* 10 ms */
.block_erasers =
{
@@ -2396,15 +2257,13 @@
.vendor = "Atmel",
.name = "AT45CS1282",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45CS1282,
.total_size = 16896 /* No power of two sizes */,
.page_size = 1056 /* No power of two sizes */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77 (4 dummy bytes); write 0x9A (via buffer) */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT45CS1282} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2428,15 +2287,13 @@
.vendor = "Atmel",
.name = "AT45DB011D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB011D,
.total_size = 128 /* or 132, determined from status register */,
.page_size = 256 /* or 264, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB011D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2470,15 +2327,13 @@
.vendor = "Atmel",
.name = "AT45DB021D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB021D,
.total_size = 256 /* or 264, determined from status register */,
.page_size = 256 /* or 264, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB021D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2512,15 +2367,13 @@
.vendor = "Atmel",
.name = "AT45DB041D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB041D,
.total_size = 512 /* or 528, determined from status register */,
.page_size = 256 /* or 264, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB041D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2554,15 +2407,13 @@
.vendor = "Atmel",
.name = "AT45DB081D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB081D,
.total_size = 1024 /* or 1056, determined from status register */,
.page_size = 256 /* or 264, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB081D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2596,15 +2447,13 @@
.vendor = "Atmel",
.name = "AT45DB161D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB161D,
.total_size = 2048 /* or 2112, determined from status register */,
.page_size = 512 /* or 528, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB161D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2638,15 +2487,13 @@
.vendor = "Atmel",
.name = "AT45DB321C",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321C,
.total_size = 4224 /* No power of two sizes */,
.page_size = 528 /* No power of two sizes */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77 (4 dummy bytes); write 0x9A (via buffer) */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, ATMEL_AT45DB321C} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2681,15 +2528,13 @@
.vendor = "Atmel",
.name = "AT45DB321D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321D,
.total_size = 4096 /* or 4224, determined from status register */,
.page_size = 512 /* or 528, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB321D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2723,15 +2568,13 @@
.vendor = "Atmel",
.name = "AT45DB321E",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321C,
.total_size = 4096 /* or 4224, determined from status register */,
.page_size = 512 /* or 528, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB321C} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2765,15 +2608,13 @@
.vendor = "Atmel",
.name = "AT45DB642D",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB642D,
.total_size = 8192 /* or 8448, determined from status register */,
.page_size = 1024 /* or 1056, determined from status register */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ {probe_spi_at45db, {FIXME, {ATMEL_ID, ATMEL_AT45DB642D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -2807,13 +2648,11 @@
.vendor = "Atmel",
.name = "AT49BV512",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49BV512,
.total_size = 64,
.page_size = 64,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49BV512} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2831,13 +2670,11 @@
.vendor = "Atmel",
.name = "AT49F002(N)",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F002N,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F002N} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2863,13 +2700,11 @@
.vendor = "Atmel",
.name = "AT49F002(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F002NT,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F002NT} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2895,13 +2730,11 @@
.vendor = "Atmel",
.name = "AT49(H)F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F010,
.total_size = 128,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F010} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2920,13 +2753,11 @@
.vendor = "Atmel",
.name = "AT49F020",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F020,
.total_size = 256,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F020} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2951,13 +2782,11 @@
.vendor = "Atmel",
.name = "AT49F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F040,
.total_size = 512,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F040} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -2982,13 +2811,11 @@
.vendor = "Atmel",
.name = "AT49F080",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F080,
.total_size = 1024,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F080} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -3014,13 +2841,11 @@
.vendor = "Atmel",
.name = "AT49F080T",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F080T,
.total_size = 1024,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ATMEL_ID, ATMEL_AT49F080T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -3045,13 +2870,11 @@
.vendor = "Atmel",
.name = "AT49LH002",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49LH002,
.total_size = 256,
.page_size = 0, /* unused */
.feature_bits = FEATURE_REGISTERMAP, /* TODO: LPC OK too? */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab, /* TODO: 0xff cmd not documented? */
+ {probe_82802ab, {2, {ATMEL_ID, ATMEL_AT49LH002} } }, /* TODO: 0xff cmd not documented? */
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -3081,13 +2904,11 @@
.vendor = "Catalyst",
.name = "CAT28F512",
.bustype = BUS_PARALLEL,
- .manufacture_id = CATALYST_ID,
- .model_id = CATALYST_CAT28F512,
.total_size = 64,
.page_size = 0, /* unused */
.feature_bits = 0,
.tested = TEST_OK_PR,
- .probe = probe_jedec, /* FIXME! */
+ {probe_jedec, {2, {CATALYST_ID, CATALYST_CAT28F512} } }, /* FIXME! */
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3105,13 +2926,11 @@
.vendor = "Bright",
.name = "BM29F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = BRIGHT_ID,
- .model_id = BRIGHT_BM29F040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {BRIGHT_ID, BRIGHT_BM29F040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3132,13 +2951,11 @@
.vendor = "ESMT",
.name = "F49B002UA",
.bustype = BUS_PARALLEL,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F49B002UA,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ESMT_ID, ESMT_F49B002UA} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -3164,13 +2981,11 @@
.vendor = "ESMT",
.name = "F25L008A",
.bustype = BUS_SPI,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F25L008A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ESMT_ID, ESMT_F25L008A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3199,13 +3014,11 @@
.vendor = "ESMT",
.name = "F25L32PA",
.bustype = BUS_SPI,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F25L32PA,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ESMT_ID, ESMT_F25L32PA} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3234,13 +3047,11 @@
.vendor = "Eon",
.name = "EN25B05",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B05} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3268,13 +3079,11 @@
.vendor = "Eon",
.name = "EN25B05T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B05} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3302,13 +3111,11 @@
.vendor = "Eon",
.name = "EN25B10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3336,13 +3143,11 @@
.vendor = "Eon",
.name = "EN25B10T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3370,13 +3175,11 @@
.vendor = "Eon",
.name = "EN25B20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3405,13 +3208,11 @@
.vendor = "Eon",
.name = "EN25B20T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3440,13 +3241,11 @@
.vendor = "Eon",
.name = "EN25B40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3475,13 +3274,11 @@
.vendor = "Eon",
.name = "EN25B40T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3510,13 +3307,11 @@
.vendor = "Eon",
.name = "EN25B80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3545,13 +3340,11 @@
.vendor = "Eon",
.name = "EN25B80T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3580,13 +3373,11 @@
.vendor = "Eon",
.name = "EN25B16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3615,13 +3406,11 @@
.vendor = "Eon",
.name = "EN25B16T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3650,13 +3439,11 @@
.vendor = "Eon",
.name = "EN25B32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3685,13 +3472,11 @@
.vendor = "Eon",
.name = "EN25B32T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3720,13 +3505,11 @@
.vendor = "Eon",
.name = "EN25B64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3755,13 +3538,11 @@
.vendor = "Eon",
.name = "EN25B64T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25B64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3790,13 +3571,11 @@
.vendor = "Eon",
.name = "EN25F05",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F05} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3828,13 +3607,11 @@
.vendor = "Eon",
.name = "EN25F10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3866,13 +3643,11 @@
.vendor = "Eon",
.name = "EN25F20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3904,13 +3679,11 @@
.vendor = "Eon",
.name = "EN25F40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3939,13 +3712,11 @@
.vendor = "Eon",
.name = "EN25F80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -3974,13 +3745,11 @@
.vendor = "Eon",
.name = "EN25F16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4009,13 +3778,11 @@
.vendor = "Eon",
.name = "EN25F32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4044,13 +3811,11 @@
.vendor = "Eon",
.name = "EN25F64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25F64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4079,14 +3844,12 @@
.vendor = "Eon",
.name = "EN25Q40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q40,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4115,14 +3878,12 @@
.vendor = "Eon",
.name = "EN25Q80(A)",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4153,14 +3914,12 @@
.vendor = "Eon",
.name = "EN25Q16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q16,
.total_size = 2048,
.page_size = 256,
/* OTP: D16 512B/Q16 128B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4193,14 +3952,12 @@
.vendor = "Eon",
.name = "EN25Q32(A/B)",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q32,
.total_size = 4096,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4229,14 +3986,12 @@
.vendor = "Eon",
.name = "EN25Q64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q64,
.total_size = 8192,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4265,14 +4020,12 @@
.vendor = "Eon",
.name = "EN25Q128",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q128,
.total_size = 16384,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25Q128} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4300,8 +4053,6 @@
.vendor = "Eon",
.name = "EN25QH16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH16,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
@@ -4309,7 +4060,7 @@
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25QH16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4338,8 +4089,6 @@
.vendor = "Eon",
.name = "EN25QH32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH32,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
@@ -4347,7 +4096,7 @@
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25QH32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -4376,8 +4125,6 @@
.vendor = "Eon",
.name = "EN25QH64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH64,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
@@ -4385,7 +4132,7 @@
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25QH64} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4413,8 +4160,6 @@
.vendor = "Eon",
.name = "EN25QH128",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH128,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
@@ -4422,7 +4167,7 @@
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25QH128} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4450,14 +4195,12 @@
.vendor = "Eon",
.name = "EN25S10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S10,
.total_size = 128,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S10} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4485,14 +4228,12 @@
.vendor = "Eon",
.name = "EN25S20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S20,
.total_size = 256,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S20} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4520,14 +4261,12 @@
.vendor = "Eon",
.name = "EN25S40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S40,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S40} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4555,14 +4294,12 @@
.vendor = "Eon",
.name = "EN25S80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S80} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4590,14 +4327,12 @@
.vendor = "Eon",
.name = "EN25S16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S16,
.total_size = 2048,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S16} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4628,14 +4363,12 @@
.vendor = "Eon",
.name = "EN25S32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S32,
.total_size = 4096,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S32} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4666,14 +4399,12 @@
.vendor = "Eon",
.name = "EN25S64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S64,
.total_size = 8192,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, EON_EN25S64} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -4701,13 +4432,11 @@
.vendor = "Eon",
.name = "EN29F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {3, {EON_ID, EON_EN29F010} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4729,13 +4458,11 @@
.vendor = "Eon",
.name = "EN29F002(A)(N)B",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F002B,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {4, {EON_ID, EON_EN29F002B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4761,13 +4488,11 @@
.vendor = "Eon",
.name = "EN29F002(A)(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F002T,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {4, {EON_ID, EON_EN29F002T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4793,13 +4518,11 @@
.vendor = "Eon",
.name = "EN29LV640B",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29LV640B,
.total_size = 8192,
.page_size = 8192,
.feature_bits = 0,
.tested = TEST_OK_PREW,
- .probe = probe_en29lv640b,
+ {probe_en29lv640b, {3, {EON_ID, EON_EN29LV640B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4823,13 +4546,11 @@
.vendor = "Fujitsu",
.name = "MBM29F004BC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F004BC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {FUJITSU_ID, FUJITSU_MBM29F004BC} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4855,13 +4576,11 @@
.vendor = "Fujitsu",
.name = "MBM29F004TC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F004TC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {FUJITSU_ID, FUJITSU_MBM29F004TC} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -4888,13 +4607,11 @@
.vendor = "Fujitsu",
.name = "MBM29F400BC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F400BC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {FUJITSU_ID, FUJITSU_MBM29F400BC} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (m29f400bt.c) */
.block_erasers =
{
@@ -4920,13 +4637,11 @@
.vendor = "Fujitsu",
.name = "MBM29F400TC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F400TC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {FUJITSU_ID, FUJITSU_MBM29F400TC} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (m29f400bt.c) */
.block_erasers =
{
@@ -4952,13 +4667,11 @@
.vendor = "Fujitsu",
.name = "MBM29LV160BE",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29LV160BE,
.total_size = 2 * 1024,
.page_size = 0,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {FUJITSU_ID, FUJITSU_MBM29LV160BE} } },
.probe_timing = TIMING_IGNORED,
.block_erasers =
{
@@ -4984,13 +4697,11 @@
.vendor = "Fujitsu",
.name = "MBM29LV160TE",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29LV160TE,
.total_size = 2 * 1024,
.page_size = 0,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {FUJITSU_ID, FUJITSU_MBM29LV160TE} } },
.probe_timing = TIMING_IGNORED,
.block_erasers =
{
@@ -5016,14 +4727,12 @@
.vendor = "GigaDevice",
.name = "GD25LQ32",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25LQ32,
.total_size = 4096,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25LQ32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5055,13 +4764,11 @@
.vendor = "GigaDevice",
.name = "GD25Q512",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q512} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -5089,13 +4796,11 @@
.vendor = "GigaDevice",
.name = "GD25Q10",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q10} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -5126,13 +4831,11 @@
.vendor = "GigaDevice",
.name = "GD25Q20(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5164,13 +4867,11 @@
.vendor = "GigaDevice",
.name = "GD25Q40(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5202,14 +4903,12 @@
.vendor = "GigaDevice",
.name = "GD25Q80(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q80,
.total_size = 1024,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5241,14 +4940,12 @@
.vendor = "GigaDevice",
.name = "GD25Q16(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q16,
.total_size = 2048,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5280,14 +4977,12 @@
.vendor = "GigaDevice",
.name = "GD25Q32(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q32,
.total_size = 4096,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5319,14 +5014,12 @@
.vendor = "GigaDevice",
.name = "GD25Q64(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q64,
.total_size = 8192,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5358,14 +5051,12 @@
.vendor = "GigaDevice",
.name = "GD25Q128B",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q128,
.total_size = 16384,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25Q128} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5397,14 +5088,12 @@
.vendor = "GigaDevice",
.name = "GD25T80",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25T80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GIGADEVICE_ID, GIGADEVICE_GD25T80} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -5435,13 +5124,11 @@
.vendor = "Hyundai",
.name = "HY29F002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F002T,
.total_size = 256,
.page_size = 256 * 1024,
.feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {HYUNDAI_ID, HYUNDAI_HY29F002T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5467,13 +5154,11 @@
.vendor = "Hyundai",
.name = "HY29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F002B,
.total_size = 256,
.page_size = 256 * 1024,
.feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {HYUNDAI_ID, HYUNDAI_HY29F002B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5499,13 +5184,11 @@
.vendor = "Hyundai",
.name = "HY29F040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {HYUNDAI_ID, HYUNDAI_HY29F040A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5526,14 +5209,12 @@
.vendor = "Intel",
.name = "25F160S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F160S33B8,
.total_size = 2048,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F160S33B8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5565,14 +5246,12 @@
.vendor = "Intel",
.name = "25F160S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F160S33T8,
.total_size = 2048,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F160S33T8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5604,14 +5283,12 @@
.vendor = "Intel",
.name = "25F320S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F320S33B8,
.total_size = 4096,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F320S33B8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5643,14 +5320,12 @@
.vendor = "Intel",
.name = "25F320S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F320S33T8,
.total_size = 4096,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F320S33T8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5682,14 +5357,12 @@
.vendor = "Intel",
.name = "25F640S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F640S33B8,
.total_size = 8192,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F640S33B8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5721,14 +5394,12 @@
.vendor = "Intel",
.name = "25F640S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F640S33T8,
.total_size = 8192,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {INTEL_ID, INTEL_25F640S33T8} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -5760,12 +5431,11 @@
.vendor = "Intel",
.name = "28F001BN/BX-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F001B,
.total_size = 128,
.page_size = 128 * 1024, /* 8k + 2x4k + 112k */
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {INTEL_ID, INTEL_28F001B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5787,12 +5457,11 @@
.vendor = "Intel",
.name = "28F001BN/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F001T,
.total_size = 128,
.page_size = 128 * 1024, /* 112k + 2x4k + 8k */
+ .feature_bits = 0,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {INTEL_ID, INTEL_28F001T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5814,12 +5483,11 @@
.vendor = "Intel",
.name = "28F002BC/BL/BV/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F002T,
.total_size = 256,
.page_size = 256 * 1024,
+ .feature_bits = 0,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F002T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5841,12 +5509,11 @@
.vendor = "Intel",
.name = "28F008S3/S5/SC",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004S3,
.total_size = 512,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F004S3} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5864,12 +5531,11 @@
.vendor = "Intel",
.name = "28F004B5/BE/BV/BX-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004B,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F004B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5891,12 +5557,11 @@
.vendor = "Intel",
.name = "28F004B5/BE/BV/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004T,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F004T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5918,13 +5583,11 @@
.vendor = "Intel",
.name = "28F400BV/BX/CE/CV-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F400B,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.feature_bits = FEATURE_ADDR_SHIFTED,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F400B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5946,13 +5609,11 @@
.vendor = "Intel",
.name = "28F400BV/BX/CE/CV-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F400T,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.feature_bits = FEATURE_ADDR_SHIFTED,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_28F400T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -5974,13 +5635,11 @@
.vendor = "Intel",
.name = "82802AB",
.bustype = BUS_FWH,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_82802AB,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_82802AB} } },
.probe_timing = TIMING_IGNORED, /* routine does not use probe_timing (82802ab.c) */
.block_erasers =
{
@@ -5999,13 +5658,11 @@
.vendor = "Intel",
.name = "82802AC",
.bustype = BUS_FWH,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_82802AC,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {INTEL_ID, INTEL_82802AC} } },
.probe_timing = TIMING_IGNORED, /* routine does not use probe_timing (82802ab.c) */
.block_erasers =
{
@@ -6024,12 +5681,11 @@
.vendor = "Macronix",
.name = "MX23L3254",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX23L3254,
.total_size = 4096,
.page_size = 256,
+ .feature_bits = 0,
.tested = {.probe = OK, .read = OK, .erase = NA, .write = NA},
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX23L3254} } },
.probe_timing = TIMING_ZERO,
.write = NULL, /* MX23L3254 is a mask ROM, so it is read-only */
.read = spi_chip_read, /* Fast read (0x0B) supported */
@@ -6040,14 +5696,12 @@
.vendor = "Macronix",
.name = "MX25L512(E)/MX25V512(C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L512,
.total_size = 64,
.page_size = 256,
/* MX25L512E supports SFDP */
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L512} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6079,14 +5733,12 @@
.vendor = "Macronix",
.name = "MX25L1005(C)/MX25L1006E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1005,
.total_size = 128,
.page_size = 256,
/* MX25L1006E supports SFDP */
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1005} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6115,13 +5767,11 @@
.vendor = "Macronix",
.name = "MX25L2005(C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L2005,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L2005} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6153,13 +5803,11 @@
.vendor = "Macronix",
.name = "MX25L4005(A/C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L4005,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L4005} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6191,13 +5839,11 @@
.vendor = "Macronix",
.name = "MX25L8005/MX25V8005",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L8005,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L8005} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6229,13 +5875,11 @@
.vendor = "Macronix",
.name = "MX25L1605",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1605} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6264,14 +5908,12 @@
.vendor = "Macronix",
.name = "MX25L1605A/MX25L1606E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 (MX25L1606E only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1605} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6303,13 +5945,11 @@
.vendor = "Macronix",
.name = "MX25L1605D/MX25L1608D/MX25L1673E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1605} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6338,14 +5978,12 @@
.vendor = "Macronix",
.name = "MX25L1635D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1635D,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1635D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6374,14 +6012,12 @@
.vendor = "Macronix",
.name = "MX25L1635E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1635E,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L1635E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6410,13 +6046,11 @@
.vendor = "Macronix",
.name = "MX25L3205(A)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L3205} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6445,14 +6079,12 @@
.vendor = "Macronix",
.name = "MX25L3205D/MX25L3208D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L3205} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6481,14 +6113,12 @@
.vendor = "Macronix",
.name = "MX25L3206E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L3205} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6520,14 +6150,12 @@
.vendor = "Macronix",
.name = "MX25L3273E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L3205} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6559,14 +6187,12 @@
.vendor = "Macronix",
.name = "MX25L3235D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3235D,
.total_size = 4096,
.page_size = 256,
/* OTP: 256B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L3235D} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6595,14 +6221,12 @@
.vendor = "Macronix",
.name = "MX25L6405(D)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* MX25L6405D has 64B of OTP; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L6405} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6631,14 +6255,12 @@
.vendor = "Macronix",
.name = "MX25L6406E/MX25L6436E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* OTP: 06E 64B/36E 512B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L6405} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6667,15 +6289,13 @@
.vendor = "Macronix",
.name = "MX25L6445E/MX25L6473E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 512B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L6405} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6707,14 +6327,12 @@
.vendor = "Macronix",
.name = "MX25L12805(D)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L12805,
.total_size = 16384,
.page_size = 256,
/* MX25L12805D has 64B of OTP; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25L12805} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6743,15 +6361,13 @@
.vendor = "Macronix",
.name = "MX25U1635E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U1635E,
.total_size = 2048,
.page_size = 256,
/* OTP: 512B total; enter 0xB1, exit 0xC1 */
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25U1635E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6784,8 +6400,6 @@
.vendor = "Macronix",
.name = "MX25U3235E/F",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U3235E,
.total_size = 4096,
.page_size = 256,
/* F model supports SFDP */
@@ -6793,7 +6407,7 @@
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25U3235E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6826,8 +6440,6 @@
.vendor = "Macronix",
.name = "MX25U6435E/F",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U6435E,
.total_size = 8192,
.page_size = 256,
/* F model supports SFDP */
@@ -6835,7 +6447,7 @@
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, MACRONIX_MX25U6435E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6868,13 +6480,11 @@
.vendor = "Macronix",
.name = "MX29F001B",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F001B,
.total_size = 128,
.page_size = 32 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29F001B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6901,13 +6511,11 @@
.vendor = "Macronix",
.name = "MX29F001T",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F001T,
.total_size = 128,
.page_size = 32 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29F001T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6934,13 +6542,11 @@
.vendor = "Macronix",
.name = "MX29F002(N)B",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F002B,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29F002B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6966,13 +6572,11 @@
.vendor = "Macronix",
.name = "MX29F002(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29F002T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -6998,13 +6602,11 @@
.vendor = "Macronix",
.name = "MX29F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29F040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7025,13 +6627,11 @@
.vendor = "Macronix",
.name = "MX29LV040",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29LV040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {MACRONIX_ID, MACRONIX_MX29LV040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7052,13 +6652,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P05-A",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P05A,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P05A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7086,13 +6684,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P05",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P05_RES,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ {probe_spi_res1, {1, {ST_M25P05_RES} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7115,13 +6711,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P10-A",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P10A,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P10A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7145,13 +6739,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P10",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P10_RES,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ {probe_spi_res1, {1, {ST_M25P10_RES} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7174,13 +6766,11 @@
.vendor = "Micron/Numonyx/ST", /* Numonyx */
.name = "M25P20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7203,13 +6793,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P20-old",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P20_RES,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res1,
+ {probe_spi_res1, {1, {ST_M25P20_RES} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7232,13 +6820,11 @@
.vendor = "Micron/Numonyx/ST", /* Numonyx */
.name = "M25P40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7261,13 +6847,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P40-old",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P40_RES,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ {probe_spi_res1, {1, {ST_M25P40_RES} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7289,13 +6873,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7318,13 +6900,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7347,13 +6927,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P32",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7376,13 +6954,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P64",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7405,13 +6981,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25P128",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P128,
.total_size = 16384,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25P128} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7434,13 +7008,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PE10",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PE10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7466,13 +7038,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PE20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PE20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7498,13 +7068,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PE40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PE40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7530,13 +7098,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PE80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PE80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7562,13 +7128,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PE16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PE16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7594,14 +7158,12 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PX80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX80,
.total_size = 1024,
.page_size = 256,
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PX80} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7626,14 +7188,12 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PX16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX16,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PX16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7659,14 +7219,12 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PX32",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX32,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PX32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7692,14 +7250,12 @@
.vendor = "Micron/Numonyx/ST",
.name = "M25PX64",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX64,
.total_size = 8192,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M25PX64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7725,12 +7281,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M45PE10",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE10,
.total_size = 128,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M45PE10} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7752,12 +7307,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M45PE20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE20,
.total_size = 256,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M45PE20} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7779,12 +7333,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M45PE40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE40,
.total_size = 512,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M45PE40} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7806,12 +7359,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M45PE80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE80,
.total_size = 1024,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M45PE80} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7833,12 +7385,11 @@
.vendor = "Micron/Numonyx/ST",
.name = "M45PE16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE16,
.total_size = 2048,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_M45PE16} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -7860,15 +7411,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q016",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q016__1E,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q016__1E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7897,15 +7446,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q032..1E",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q032__1E,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q032__1E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7931,15 +7478,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q032..3E",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q032__3E,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q032__3E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7965,15 +7510,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q064..1E", /* ..1E = 1.8V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q064__1E,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q064__1E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -7999,15 +7542,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q064..3E", /* ..3E = 3V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q064__3E,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q064__3E} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8033,15 +7574,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q128..1E", /* ..1E = 1.8V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q128__1E,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q128__1E} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -8066,15 +7605,13 @@
.vendor = "Micron/Numonyx/ST",
.name = "N25Q128..3E", /* ..3E = 3V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q128__3E,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, ST_N25Q128__3E} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -8099,13 +7636,11 @@
.vendor = "MoselVitelic",
.name = "V29C51000B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51000B,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29C51000B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8126,13 +7661,11 @@
.vendor = "MoselVitelic",
.name = "V29C51000T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51000T,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29C51000T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8153,13 +7686,11 @@
.vendor = "MoselVitelic",
.name = "V29C51400B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51400B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29C51400B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8180,13 +7711,11 @@
.vendor = "MoselVitelic",
.name = "V29C51400T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51400T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29C51400T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8207,13 +7736,11 @@
.vendor = "MoselVitelic",
.name = "V29LC51000",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51000,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29LC51000} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8234,13 +7761,11 @@
.vendor = "MoselVitelic",
.name = "V29LC51001",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51001,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29LC51001} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8261,13 +7786,11 @@
.vendor = "MoselVitelic",
.name = "V29LC51002",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51002,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, MVC_V29LC51002} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8288,13 +7811,11 @@
.vendor = "Nantronics",
.name = "N25S10",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8329,13 +7850,11 @@
.vendor = "Nantronics",
.name = "N25S20",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8370,13 +7889,11 @@
.vendor = "Nantronics",
.name = "N25S40",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8411,13 +7928,11 @@
.vendor = "Nantronics",
.name = "N25S80",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8449,13 +7964,11 @@
.vendor = "Nantronics",
.name = "N25S16",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8484,13 +7997,11 @@
.vendor = "PMC",
.name = "Pm25LD256C",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD256C,
.total_size = 32,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LD256C} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8521,13 +8032,11 @@
.vendor = "PMC",
.name = "Pm25LD512(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LD512} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8559,13 +8068,11 @@
.vendor = "PMC",
.name = "Pm25LD010(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LD010} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8597,13 +8104,11 @@
.vendor = "PMC",
.name = "Pm25LD020(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LD020} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8635,13 +8140,11 @@
.vendor = "PMC",
.name = "Pm25LD040(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8673,13 +8176,11 @@
.vendor = "PMC",
.name = "Pm25LV512(A)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM25LV512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2, /* The continuation code is transferred as the 3rd byte m( */
+ {probe_spi_res2, {2, {PMC_ID_NOPREFIX, PMC_PM25LV512} } }, /* The continuation code is transferred as the 3rd byte m( */
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8705,13 +8206,11 @@
.vendor = "PMC",
.name = "Pm25LV010",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM25LV010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2, /* The continuation code is transferred as the 3rd byte m( */
+ {probe_spi_res2, {2, {PMC_ID_NOPREFIX, PMC_PM25LV010} } }, /* The continuation code is transferred as the 3rd byte m( */
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8737,13 +8236,11 @@
.vendor = "PMC",
.name = "Pm25LV010A",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV010} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8769,13 +8266,11 @@
.vendor = "PMC",
.name = "Pm25LV020",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV020} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8801,13 +8296,11 @@
.vendor = "PMC",
.name = "Pm25LV040",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8833,13 +8326,11 @@
.vendor = "PMC",
.name = "Pm25LV080B",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV080B,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV080B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8871,13 +8362,11 @@
.vendor = "PMC",
.name = "Pm25LV016B",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV016B,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, PMC_PM25LV016B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -8909,13 +8398,11 @@
.vendor = "PMC",
.name = "Pm29F002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM29F002T,
.total_size = 256,
.page_size = 8 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM29F002T} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -8941,13 +8428,11 @@
.vendor = "PMC",
.name = "Pm29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM29F002B,
.total_size = 256,
.page_size = 8 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM29F002B} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -8973,13 +8458,11 @@
.vendor = "PMC",
.name = "Pm39LV010",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39F010, /* Pm39LV010 and Pm39F010 have identical IDs but different voltage */
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM39F010 /* Pm39LV010 and Pm39F010 have identical IDs but different voltage */} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -9003,13 +8486,11 @@
.vendor = "PMC",
.name = "Pm39LV020",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM39LV020} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -9033,13 +8514,11 @@
.vendor = "PMC",
.name = "Pm39LV040",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM39LV040} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -9063,13 +8542,11 @@
.vendor = "PMC",
.name = "Pm39LV512",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM39LV512} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -9093,13 +8570,11 @@
.vendor = "PMC",
.name = "Pm49FL002",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM49FL002,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM49FL002} } },
.probe_timing = TIMING_ZERO, /* routine is wrapper to probe_jedec (pm49fl00x.c) */
.block_erasers =
{
@@ -9124,13 +8599,11 @@
.vendor = "PMC",
.name = "Pm49FL004",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM49FL004,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {PMC_ID_NOPREFIX, PMC_PM49FL004} } },
.probe_timing = TIMING_ZERO, /* routine is wrapper to probe_jedec (pm49fl00x.c) */
.block_erasers =
{
@@ -9155,13 +8628,11 @@
.vendor = "Sanyo",
.name = "LE25FW106",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW106,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FW106} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9186,13 +8657,11 @@
.vendor = "Sanyo",
.name = "LE25FW406A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW406A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FW406A} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9217,13 +8686,11 @@
.vendor = "Sanyo",
.name = "LE25FU406B",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FU406B,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FU406B} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9248,12 +8715,11 @@
.vendor = "Sanyo",
.name = "LE25FW203A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW203A,
.total_size = 256,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SANYO_ID, SANYO_LE25FW203A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9279,12 +8745,11 @@
.vendor = "Sanyo",
.name = "LE25FW403A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW403A,
.total_size = 512,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SANYO_ID, SANYO_LE25FW403A} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9309,13 +8774,11 @@
.vendor = "Sanyo",
.name = "LE25FW418A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW418A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FW418A} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9340,13 +8803,11 @@
.vendor = "Sanyo",
.name = "LE25FW806",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW806,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FW806} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9374,13 +8835,11 @@
.vendor = "Sanyo",
.name = "LE25FW808",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW808,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SANYO_ID, SANYO_LE25FW808} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9405,12 +8864,11 @@
.vendor = "Sharp",
.name = "LH28F008BJT-BTLZ1",
.bustype = BUS_PARALLEL,
- .manufacture_id = SHARP_ID,
- .model_id = SHARP_LH28F008BJ__PB,
.total_size = 1024,
.page_size = 64 * 1024,
+ .feature_bits = 0,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SHARP_ID, SHARP_LH28F008BJ__PB} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9435,13 +8893,11 @@
.vendor = "Sharp",
.name = "LHF00L04",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SHARP_ID,
- .model_id = SHARP_LHF00L04,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET | FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SHARP_ID, SHARP_LHF00L04} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9468,13 +8924,11 @@
.vendor = "Spansion",
.name = "S25FL004A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL004A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL004A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9497,13 +8951,11 @@
.vendor = "Spansion",
.name = "S25FL008A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL008A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL008A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9526,13 +8978,11 @@
.vendor = "Spansion",
.name = "S25FL016A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL016A,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL016A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9555,13 +9005,11 @@
.vendor = "Spansion",
.name = "S25FL032A/P",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL032A,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL032A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9584,13 +9032,11 @@
.vendor = "Spansion",
.name = "S25FL064A/P",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL064A,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL064A} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9613,13 +9059,11 @@
.vendor = "Spansion",
.name = "S25FL204K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL204,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL204} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9647,13 +9091,11 @@
.vendor = "Spansion",
.name = "S25FL208K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL208,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL208} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9681,14 +9123,12 @@
.vendor = "Spansion",
.name = "S25FL116K/S25FL216K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL216,
.total_size = 2048,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (S25FL116K only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL216} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9716,14 +9156,12 @@
.vendor = "Spansion",
.name = "S25FL132K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL132K,
.total_size = 4096,
.page_size = 256,
/* OTP: 768B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL132K} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9751,14 +9189,12 @@
.vendor = "Spansion",
.name = "S25FL164K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL164K,
.total_size = 8192,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL164K} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9786,15 +9222,13 @@
.vendor = "Spansion",
.name = "S25FL128S......0", /* uniform 256kB sectors */
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL128,
.total_size = 16384,
.page_size = 256,
/* supports 4B addressing */
/* OTP: 1024B total, 32B reserved; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SPANSION_ID, SPANSION_S25FL128} } },
.probe_timing = TIMING_ZERO,
.block_erasers = {
{
@@ -9822,13 +9256,11 @@
.vendor = "SST",
.name = "SST25LF020A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020_REMS,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF020_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9854,13 +9286,11 @@
.vendor = "SST",
.name = "SST25LF040A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SST_ID, SST_SST25VF040_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9886,13 +9316,11 @@
.vendor = "SST",
.name = "SST25LF080(A)",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF080_REMS,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ {probe_spi_res2, {2, {SST_ID, SST_SST25VF080_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9918,13 +9346,11 @@
.vendor = "SST",
.name = "SST25VF512A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF512A_REMS,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF512A_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9956,13 +9382,11 @@
.vendor = "SST",
.name = "SST25VF010",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF010_REMS,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF010_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -9994,13 +9418,11 @@
.vendor = "SST",
.name = "SST25VF020",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020_REMS,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF020_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10026,13 +9448,11 @@
.vendor = "SST",
.name = "SST25VF020B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020B,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF020B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10064,13 +9484,11 @@
.vendor = "SST",
.name = "SST25VF040",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PR,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF040_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10096,13 +9514,11 @@
.vendor = "SST",
.name = "SST25VF040B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040B,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF040B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10134,13 +9550,11 @@
.vendor = "SST",
.name = "SST25VF040B.REMS",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040B_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {SST_ID, SST_SST25VF040B_REMS} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10172,13 +9586,11 @@
.vendor = "SST",
.name = "SST25VF080B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF080B,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF080B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10210,13 +9622,11 @@
.vendor = "SST",
.name = "SST25VF016B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF016B,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF016B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10248,13 +9658,11 @@
.vendor = "SST",
.name = "SST25VF032B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF032B,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF032B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10286,13 +9694,11 @@
.vendor = "SST",
.name = "SST25VF064C",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF064C,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25VF064C} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10324,13 +9730,11 @@
.vendor = "SST",
.name = "SST25WF512",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25WF512} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10359,13 +9763,11 @@
.vendor = "SST",
.name = "SST25WF010",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25WF010} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10394,13 +9796,11 @@
.vendor = "SST",
.name = "SST25WF020",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25WF020} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10432,13 +9832,11 @@
.vendor = "SST",
.name = "SST25WF040",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25WF040} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10470,13 +9868,11 @@
.vendor = "SST",
.name = "SST25WF080",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF080,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, SST_SST25WF080} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -10508,13 +9904,11 @@
.vendor = "SST",
.name = "SST28SF040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST28SF040,
.total_size = 512,
.page_size = 256,
.feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SST_ID, SST_SST28SF040} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst28sf040.c) */
.block_erasers =
{
@@ -10536,13 +9930,11 @@
.vendor = "SST",
.name = "SST29EE010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29EE010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST29EE010} } },
.probe_timing = 10,
.block_erasers =
{
@@ -10560,13 +9952,11 @@
.vendor = "SST",
.name = "SST29LE010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29LE010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST29LE010} } },
.probe_timing = 10,
.block_erasers =
{
@@ -10584,13 +9974,11 @@
.vendor = "SST",
.name = "SST29EE020A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29EE020A,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST29EE020A} } },
.probe_timing = 10,
.block_erasers =
{
@@ -10608,13 +9996,11 @@
.vendor = "SST",
.name = "SST29LE020",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29LE020,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST29LE020} } },
.probe_timing = 10,
.block_erasers =
{
@@ -10632,13 +10018,11 @@
.vendor = "SST",
.name = "SST39SF512",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39SF512} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10659,13 +10043,11 @@
.vendor = "SST",
.name = "SST39SF010A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF010,
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39SF010} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10686,13 +10068,11 @@
.vendor = "SST",
.name = "SST39SF020A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39SF020} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10713,13 +10093,11 @@
.vendor = "SST",
.name = "SST39SF040",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39SF040} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10740,13 +10118,11 @@
.vendor = "SST",
.name = "SST39VF512",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39VF512} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10767,13 +10143,11 @@
.vendor = "SST",
.name = "SST39VF010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF010,
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39VF010} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10794,13 +10168,11 @@
.vendor = "SST",
.name = "SST39VF020",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39VF020} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10821,13 +10193,11 @@
.vendor = "SST",
.name = "SST39VF040",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39VF040} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10848,13 +10218,11 @@
.vendor = "SST",
.name = "SST39VF080",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF080,
.total_size = 1024,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST39VF080} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10878,13 +10246,11 @@
.vendor = "SST",
.name = "SST49LF002A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF002A,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF002A} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10910,13 +10276,11 @@
.vendor = "SST",
.name = "SST49LF003A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF003A,
.total_size = 384,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF003A} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10945,13 +10309,11 @@
.vendor = "SST",
.name = "SST49LF004A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF004A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF004A} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -10977,13 +10339,11 @@
.vendor = "SST",
.name = "SST49LF004C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF004C,
.total_size = 512,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SST_ID, SST_SST49LF004C} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst49lfxxxc.c) */
.block_erasers =
{
@@ -11010,13 +10370,11 @@
.vendor = "SST",
.name = "SST49LF008A",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF008A,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF008A} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -11042,13 +10400,11 @@
.vendor = "SST",
.name = "SST49LF008C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF008C,
.total_size = 1024,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SST_ID, SST_SST49LF008C} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst49lfxxxc.c) */
.block_erasers =
{
@@ -11075,13 +10431,11 @@
.vendor = "SST",
.name = "SST49LF016C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF016C,
.total_size = 2048,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SST_ID, SST_SST49LF016C} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst49lfxxxc.c) */
.block_erasers =
{
@@ -11108,13 +10462,11 @@
.vendor = "SST",
.name = "SST49LF020",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF020,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF020} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -11138,13 +10490,11 @@
.vendor = "SST",
.name = "SST49LF020A",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF020A,
.total_size = 256,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF020A} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -11168,13 +10518,11 @@
.vendor = "SST",
.name = "SST49LF040",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF040} } },
.probe_timing = 1, /* 150 ns */
.block_erasers =
{
@@ -11198,13 +10546,11 @@
.vendor = "SST",
.name = "SST49LF040B",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET | FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF040B} } },
.probe_timing = 1, /* 150ns */
.block_erasers =
{
@@ -11229,13 +10575,11 @@
.vendor = "SST",
.name = "SST49LF080A",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF080A,
.total_size = 1024,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SST_ID, SST_SST49LF080A} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -11259,13 +10603,11 @@
.vendor = "SST",
.name = "SST49LF160C",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF160C,
.total_size = 2048,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {SST_ID, SST_SST49LF160C} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst49lfxxxc.c) */
.block_erasers =
{
@@ -11292,13 +10634,11 @@
.vendor = "ST",
.name = "M29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F002B,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29F002B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11324,13 +10664,11 @@
.vendor = "ST",
.name = "M29F002T/NT",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29F002T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11356,13 +10694,11 @@
.vendor = "ST",
.name = "M29F040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29F040B} } },
.probe_timing = TIMING_ZERO, /* datasheet specifies no timing */
.block_erasers =
{
@@ -11384,13 +10720,11 @@
.vendor = "ST",
.name = "M29F400BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F400BB,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {ST_ID, ST_M29F400BB} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (m29f400bt.c) */
.block_erasers =
{
@@ -11416,13 +10750,11 @@
.vendor = "ST",
.name = "M29F400BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F400BT,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_SHIFTED | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ {probe_m29f400bt, {2, {ST_ID, ST_M29F400BT} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (m29f400bt.c) */
.block_erasers =
{
@@ -11448,13 +10780,11 @@
.vendor = "ST",
.name = "M29W010B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W010B,
.total_size = 128,
.page_size = 16 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29W010B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11475,13 +10805,11 @@
.vendor = "ST",
.name = "M29W040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29W040B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11502,13 +10830,11 @@
.vendor = "ST",
.name = "M29W512B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W512B,
.total_size = 64,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {ST_ID, ST_M29W512B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -11526,13 +10852,11 @@
.vendor = "ST",
.name = "M50FLW040A",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW040A,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FLW040A} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -11559,13 +10883,11 @@
.vendor = "ST",
.name = "M50FLW040B",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW040B,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FLW040B} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -11592,13 +10914,11 @@
.vendor = "ST",
.name = "M50FLW080A",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW080A,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FLW080A} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -11625,13 +10945,11 @@
.vendor = "ST",
.name = "M50FLW080B",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW080B,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FLW080B} } },
.probe_timing = TIMING_FIXME,
.block_erasers =
{
@@ -11658,13 +10976,11 @@
.vendor = "ST",
.name = "M50FW002",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW002,
.total_size = 256,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FW002} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (sst49lfxxxc.c) */
.block_erasers =
{
@@ -11688,13 +11004,11 @@
.vendor = "ST",
.name = "M50FW016",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW016,
.total_size = 2048,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FW016} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (82802ab.c) */
.block_erasers =
{
@@ -11713,13 +11027,11 @@
.vendor = "ST",
.name = "M50FW040",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW040,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FW040} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (82802ab.c) */
.block_erasers =
{
@@ -11738,13 +11050,11 @@
.vendor = "ST",
.name = "M50FW080",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW080,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50FW080} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (82802ab.c) */
.block_erasers =
{
@@ -11763,13 +11073,11 @@
.vendor = "ST",
.name = "M50LPW080",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50LPW080,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50LPW080} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11788,13 +11096,11 @@
.vendor = "ST",
.name = "M50LPW116",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50LPW116,
.total_size = 2048,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ {probe_82802ab, {2, {ST_ID, ST_M50LPW116} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11819,13 +11125,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51001B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51001B,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51001B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11846,13 +11150,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51001T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51001T,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51001T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11873,13 +11175,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51002B,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51002B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11899,13 +11199,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51002T,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51002T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -11925,13 +11223,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51004B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51004B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51004B} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -11952,13 +11248,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51004T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51004T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C51004T} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -11979,13 +11273,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{S,V}29C31004B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C31004B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C31004B} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -12006,13 +11298,11 @@
.vendor = "SyncMOS/MoselVitelic",
.name = "{S,V}29C31004T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C31004T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {SYNCMOS_MVC_ID, SM_MVC_29C31004T} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -12033,13 +11323,11 @@
.vendor = "TI",
.name = "TMS29F002RB",
.bustype = BUS_PARALLEL,
- .manufacture_id = TI_OLD_ID,
- .model_id = TI_TMS29F002RB,
.total_size = 256,
.page_size = 16384, /* Non-uniform sectors */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {TI_OLD_ID, TI_TMS29F002RB} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -12065,13 +11353,11 @@
.vendor = "TI",
.name = "TMS29F002RT",
.bustype = BUS_PARALLEL,
- .manufacture_id = TI_OLD_ID,
- .model_id = TI_TMS29F002RT,
.total_size = 256,
.page_size = 16384, /* Non-uniform sectors */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {TI_OLD_ID, TI_TMS29F002RT} } },
.probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */
.block_erasers =
{
@@ -12097,15 +11383,13 @@
.vendor = "Winbond",
.name = "W25Q80.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q80_V,
.total_size = 1024,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q80_V} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12137,15 +11421,13 @@
.vendor = "Winbond",
.name = "W25Q16.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q16_V,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q16_V} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12177,15 +11459,13 @@
.vendor = "Winbond",
.name = "W25Q32.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q32_V,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q32_V} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12217,15 +11497,13 @@
.vendor = "Winbond",
.name = "W25Q64.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q64_V,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q64_V} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12257,15 +11535,13 @@
.vendor = "Winbond",
.name = "W25Q128.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q128_V,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q128_V} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12297,14 +11573,12 @@
.vendor = "Winbond",
.name = "W25Q20.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q20_W,
.total_size = 256,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q20_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12336,14 +11610,12 @@
.vendor = "Winbond",
.name = "W25Q40.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q40_W,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q40_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12375,14 +11647,12 @@
.vendor = "Winbond",
.name = "W25Q80.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q80_W,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q80_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12414,15 +11684,13 @@
.vendor = "Winbond",
.name = "W25Q16.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q16_W,
.total_size = 2048,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q16_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12454,15 +11722,13 @@
.vendor = "Winbond",
.name = "W25Q32.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q32_W,
.total_size = 4096,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q32_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12494,15 +11760,13 @@
.vendor = "Winbond",
.name = "W25Q64.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q64_W,
.total_size = 8192,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25Q64_W} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12534,13 +11798,11 @@
.vendor = "Winbond",
.name = "W25X10",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X10} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12566,13 +11828,11 @@
.vendor = "Winbond",
.name = "W25X20",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X20} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12598,13 +11858,11 @@
.vendor = "Winbond",
.name = "W25X40",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X40} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12630,13 +11888,11 @@
.vendor = "Winbond",
.name = "W25X80",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X80} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12662,13 +11918,11 @@
.vendor = "Winbond",
.name = "W25X16",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X16} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12700,13 +11954,11 @@
.vendor = "Winbond",
.name = "W25X32",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X32} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12738,13 +11990,11 @@
.vendor = "Winbond",
.name = "W25X64",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, WINBOND_NEX_W25X64} } },
.probe_timing = TIMING_ZERO,
.block_erasers =
{
@@ -12776,13 +12026,11 @@
.vendor = "Winbond",
.name = "W29C010(M)/W29C011A/W29EE011/W29EE012-old",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_w29ee011,
+ {probe_w29ee011, {2, {WINBOND_ID, WINBOND_W29C010} } },
.probe_timing = TIMING_IGNORED, /* routine doesn't use probe_timing (w29ee011.c) */
.block_erasers =
{
@@ -12799,13 +12047,11 @@
.vendor = "Winbond",
.name = "W29C010(M)/W29C011A/W29EE011/W29EE012",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W29C010} } },
.probe_timing = 10, /* used datasheet for the W29C011A */
.block_erasers =
{
@@ -12822,13 +12068,11 @@
.vendor = "Winbond",
.name = "W29C020(C)/W29C022",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C020,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W29C020} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12846,13 +12090,11 @@
.vendor = "Winbond",
.name = "W29C040/P",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W29C040} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12870,13 +12112,11 @@
.vendor = "Winbond",
.name = "W39F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39F010,
.total_size = 128,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39F010} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12898,13 +12138,11 @@
.vendor = "Winbond",
.name = "W39L010",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L010,
.total_size = 128,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39L010} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12926,13 +12164,11 @@
.vendor = "Winbond",
.name = "W39L020",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L020,
.total_size = 256,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39L020} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12957,13 +12193,11 @@
.vendor = "Winbond",
.name = "W39L040",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39L040} } },
.probe_timing = 10,
.block_erasers =
{
@@ -12988,13 +12222,11 @@
.vendor = "Winbond",
.name = "W39V040A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040A} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13016,13 +12248,11 @@
.vendor = "Winbond",
.name = "W39V040B",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040B} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13044,13 +12274,11 @@
.vendor = "Winbond",
.name = "W39V040C",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040C,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040C} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13072,13 +12300,11 @@
.vendor = "Winbond",
.name = "W39V040FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040FA,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040FA} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13104,13 +12330,11 @@
.vendor = "Winbond",
.name = "W39V040FB",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040B} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13133,13 +12357,11 @@
.vendor = "Winbond",
.name = "W39V040FC",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040C,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V040C} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13161,13 +12383,11 @@
.vendor = "Winbond",
.name = "W39V080A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080A,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V080A} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13189,13 +12409,11 @@
.vendor = "Winbond",
.name = "W49F002U/N",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49F002U,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W49F002U} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13221,13 +12439,11 @@
.vendor = "Winbond",
.name = "W49F020",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49F020,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PROBE,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W49F020} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13245,13 +12461,11 @@
.vendor = "Winbond",
.name = "W49V002A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49V002A,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W49V002A} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13277,13 +12491,11 @@
.vendor = "Winbond",
.name = "W49V002FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49V002FA,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W49V002FA} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13309,13 +12521,11 @@
.vendor = "Winbond",
.name = "W39V080FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080FA,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V080FA} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13338,13 +12548,11 @@
.vendor = "Winbond",
.name = "W39V080FA (dual mode)",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080FA_DM,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ {probe_jedec, {2, {WINBOND_ID, WINBOND_W39V080FA_DM} } },
.probe_timing = 10,
.block_erasers =
{
@@ -13366,13 +12574,11 @@
.vendor = "Unknown",
.name = "SFDP-capable chip",
.bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = SFDP_DEVICE_ID,
/* We present our own "report this" text hence we do not
* want the default "This flash part has status UNTESTED..."
* text to be printed. */
.tested = TEST_OK_PREW,
- .probe = probe_spi_sfdp,
+ {probe_spi_sfdp, {FIXME, {GENERIC_MANUF_ID, SFDP_DEVICE_ID} } },
.unlock = spi_disable_blockprotect, /* is this safe? */
.read = spi_chip_read,
/* FIXME: some vendor extensions define this */
@@ -13389,13 +12595,11 @@
.vendor = "Programmer",
.name = "Opaque flash chip",
.bustype = BUS_PROG,
- .manufacture_id = PROGMANUF_ID,
- .model_id = PROGDEV_ID,
.total_size = 0,
.page_size = 256,
/* probe is assumed to work, rest will be filled in by probe */
.tested = TEST_OK_PROBE,
- .probe = probe_opaque,
+ {probe_opaque, {FIXME, {PROGMANUF_ID, PROGDEV_ID} } },
/* eraseblock sizes will be set by the probing function */
.block_erasers =
{
@@ -13411,12 +12615,11 @@
.vendor = "AMIC",
.name = "unknown AMIC SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid4,
+ {probe_spi_rdid4, {4, {AMIC_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13426,12 +12629,11 @@
.vendor = "Atmel",
.name = "unknown Atmel SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ATMEL_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13441,12 +12643,11 @@
.vendor = "Eon",
.name = "unknown Eon SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {EON_ID_NOPREFIX, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13456,12 +12657,11 @@
.vendor = "Macronix",
.name = "unknown Macronix SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {MACRONIX_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13471,12 +12671,11 @@
.vendor = "PMC",
.name = "unknown PMC SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {PMC_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13486,12 +12685,11 @@
.vendor = "SST",
.name = "unknown SST SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SST_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13501,12 +12699,11 @@
.vendor = "ST",
.name = "unknown ST SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {ST_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13516,12 +12713,11 @@
.vendor = "Sanyo",
.name = "unknown Sanyo SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {SANYO_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13531,12 +12727,11 @@
.vendor = "Winbond",
.name = "unknown Winbond (ex Nexcom) SPI chip",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {WINBOND_NEX_ID, GENERIC_DEVICE_ID} } },
.probe_timing = TIMING_ZERO,
.write = NULL,
.read = NULL,
@@ -13546,12 +12741,11 @@
.vendor = "Generic",
.name = "unknown SPI chip (RDID)",
.bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
+ {probe_spi_rdid, {3, {GENERIC_MANUF_ID, GENERIC_DEVICE_ID} } },
.write = NULL,
},
@@ -13559,12 +12753,11 @@
.vendor = "Generic",
.name = "unknown SPI chip (REMS)",
.bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = GENERIC_DEVICE_ID,
.total_size = 0,
.page_size = 256,
+ .feature_bits = 0,
.tested = TEST_BAD_PREW,
- .probe = probe_spi_rems,
+ {probe_spi_rems, {2, {GENERIC_MANUF_ID, GENERIC_DEVICE_ID} } },
.write = NULL,
},
--
http://www.hailfinger.org/
1
0
17 Jun '14
Am 16.06.2014 02:50 schrieb Stefan Tauner:
> This is based on '[PATCH 0/5] Bunch of stuff on the way to new probing'
I do like your design approach and it looks very sensible for all SPI
chips. You trim quite a lot of fat from various places and group
probe-related data with probe-related functions inside struct flashchip.
This improves readability and is also the right thing to do from a
design POV.
Besides that, draft code is an excellent way to get the discussion
going. Your no-nonsense approach also made me painfully aware of other
issues in struct flashchip which are relics from ancient times and
always worked well enough to ignore their design problems.
Thanks a lot!
First draft of a counter-proposal based on most of the design of your
patches.
Does not compile, only to illustrate what I mean by way of two examples.
Your individual probe function rewrite (except for the data->code moves)
is something I really like from a design POV, thus I didn't replicate it
here.
SPI entries in flashchips.c look exactly the same as in your rewrite
(because I think you designed the struct exceptionally well for SPI
chips), but the non-SPI entries differ (because I extended the struct to
handle the cases I'm concerned about).
I have not yet looked in detail at the probe function prototype for
probe_*, I just used that snippet from your patch as reference for now.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Index: flashrom-proberewrite/flash.h
===================================================================
--- flashrom-proberewrite/flash.h (Revision 1822)
+++ flashrom-proberewrite/flash.h (Arbeitskopie)
@@ -141,23 +141,44 @@
#define TEST_BAD_PRE (struct tested){ .probe = BAD, .read = BAD, .erase = BAD, .write = NT }
#define TEST_BAD_PREW (struct tested){ .probe = BAD, .read = BAD, .erase = BAD, .write = BAD }
+#define NUM_PROBES 3
+#define NUM_PROBE_BYTES 5 /* Values below 2 will break code. */
+
struct flashctx;
+struct registered_programmer; /* programmer.h */
+struct probe;
+struct probe_res;
+
+/* fixme */
+typedef int (probefunc_t)(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p);
typedef int (erasefunc_t)(struct flashctx *flash, unsigned int addr, unsigned int blocklen);
+struct probe_res {
+ probefunc_t *probe_func;
+ unsigned int chip_size; /* in kB */
+ int probe_feature_bits;
+ int chip_relevant_feature_bits;
+ signed int probe_timing;
+ uint8_t len;
+ uint8_t vals[NUM_PROBE_BYTES];
+};
+
+/* Feature types relevant for probing */
+#define PROBE_TIMING (1 << 0)
+#define PROBE_ADDR (1 << 1)
+#define PROBE_SIZE (1 << 2)
+
+struct probe_res_data {
+ uint8_t len;
+ uint8_t vals[NUM_PROBE_BYTES];
+};
+
struct flashchip {
const char *vendor;
const char *name;
enum chipbustype bustype;
- /*
- * With 32bit manufacture_id and model_id we can cover IDs up to
- * (including) the 4th bank of JEDEC JEP106W Standard Manufacturer's
- * Identification code.
- */
- uint32_t manufacture_id;
- uint32_t model_id;
-
/* Total chip size in kilobytes */
unsigned int total_size;
/* Chip page size in bytes */
@@ -172,13 +193,17 @@
enum test_state write;
} tested;
- int (*probe) (struct flashctx *flash);
-
- /* Delay after "enter/exit ID mode" commands in microseconds.
- * NB: negative values have special meanings, see TIMING_* below.
+ struct prober {
+ probefunc_t *func;
+ struct probe_res_data res_data;
+ int probe_feature_bits;
+ uint32_t extradata;
+ /* extradata can contain the encoded delay after "enter/exit ID mode" commands in microseconds.
+ * NB: Some values have special meanings, see TIMING_* below.
*/
- signed int probe_timing;
+ } probers[NUM_PROBES];
+
/*
* Erase blocks and associated erase function. Any chip erase function
* is stored as chip-sized virtual block together with said function.
@@ -208,22 +233,22 @@
};
struct flashctx {
- struct flashchip *chip;
+ const struct flashchip *chip;
chipaddr virtual_memory;
/* Some flash devices have an additional register space. */
chipaddr virtual_registers;
struct registered_programmer *pgm;
};
-/* Timing used in probe routines. ZERO is -2 to differentiate between an unset
- * field and zero delay.
+/* Timing used in probe routines. Add 1 to all values to differentiate between an unset field and zero delay.
*
* SPI devices will always have zero delay and ignore this field.
*/
-#define TIMING_FIXME -1
+#define TIMING_FIXME (0) & 0xffff
/* this is intentionally same value as fixme */
-#define TIMING_IGNORED -1
-#define TIMING_ZERO -2
+#define TIMING_IGNORED (0) & 0xffff
+#define TIMING(x) (x + 1) & 0xffff
+#define TIMING_MASK 0xffff
extern const struct flashchip flashchips[];
extern const unsigned int flashchips_size;
@@ -258,7 +283,7 @@
void map_flash_registers(struct flashctx *flash);
int read_memmapped(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
int erase_flash(struct flashctx *flash);
-int probe_flash(struct registered_programmer *pgm, int startchip, struct flashctx *fill_flash, int force);
+int probe_flash(struct flashctx **flashes, const struct registered_programmer *pgm);
int read_flash_to_file(struct flashctx *flash, const char *filename);
char *extract_param(const char *const *haystack, const char *needle, const char *delim);
int verify_range(struct flashctx *flash, const uint8_t *cmpbuf, unsigned int start, unsigned int len);
@@ -344,5 +369,7 @@
int spi_send_multicommand(struct flashctx *flash, struct spi_command *cmds);
uint32_t spi_get_valid_read_addr(struct flashctx *flash);
+/* programmer.c */
enum chipbustype get_buses_supported(void);
+
#endif /* !__FLASH_H__ */
Index: flashrom-proberewrite/flashchips.c
===================================================================
--- flashrom-proberewrite/flashchips.c (Revision 1822)
+++ flashrom-proberewrite/flashchips.c (Arbeitskopie)
@@ -44,6 +44,13 @@
* .page_size = Page or eraseblock(?) size in bytes
* .tested = Test status
* .probe = Probe function
+ * .probers[] = Array of probe functions
+ * {
+ * .func = Probe function
+ * .res_data = Expected probe result data
+ * .probe_feature_bits = List of feature bit types relevant to this probe
+ * .extradata = Data only relevant for this probe, e.g. timing
+ * }
* .probe_timing = Probe function delay
* .block_erasers[] = Array of erase layouts and erase functions
* {
@@ -61,14 +68,14 @@
.vendor = "AMD",
.name = "Am29F010A/B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F010B, /* Same as Am29F010A */
.total_size = 128,
.page_size = 16 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
- .probe_timing = TIMING_ZERO,
+ .probers =
+ {
+ { probe_jedec, { 2, { AMIC_ID, AMD_AM29F010B } }, PROBE_ADDR | PROBE_SIZE | PROBE_TIMING, TIMING(0) }, /* Same as Am29F010A */
+ },
.block_erasers =
{
{
@@ -84,6 +91,7 @@
.voltage = {4500, 5500},
},
+#if 0
{
.vendor = "AMD",
.name = "Am29F002(N)BB",
@@ -536,19 +544,21 @@
.read = read_memmapped,
.voltage = {3000, 3600}, /* 3.0-3.6V for type -70R, others 2.7-3.6V */
},
+#endif
{
.vendor = "AMIC",
.name = "A25L05PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L05PT,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
- .probe_timing = TIMING_ZERO,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L05PT } } },
+ { probe_spi_res, { 1, { 0x05 } } },
+ },
.block_erasers =
{
{
@@ -571,6 +581,7 @@
.voltage = {2700, 3600},
},
+#if 0
{
.vendor = "AMIC",
.name = "A25L05PU",
@@ -13567,6 +13578,7 @@
.probe = probe_spi_rems,
.write = NULL,
},
+#endif
{0}
};
--
http://www.hailfinger.org/
1
0
16 Jun '14
Am 16.06.2014 02:50 schrieb Stefan Tauner:
> Use dedicated jedec_probe_* functions where needed. The count of
> functions could be reduced in the future by using the slowest one
> instead(?).
Ah, no, that's not how it works. Each flash chip has dedicated timing
requirements: if you send the probe sequence too slowly, some chips
ignore it, and if you send it too fast, some other chips ignore it. Most
newer chips can deal with slow and fast probes, but it's by no means
guaranteed.
> To mimic previous delay behavior in the jedec_erase_* functions a
> new feature flag was introduced: FEATURE_SLOW_ERASE_CMDS
Hm. Need to reread that part.
> Also, the feature_bits field was changed from int to uint16_t.
That change increases code size and execution time because the compiler
has to emit extra instructions and/or use prefixes to handle 16bit values.
> Default make size counterintuitively increases slightly with gcc but
> shrinks with clang (about 4 kB or 0.75%).
>
> Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
More review later.
Regardsm
Carl-Daniel
--
http://www.hailfinger.org/
1
0
Re: [flashrom] [PATCH] nicintel_eeprom: New programmer for Intel Nics eeproms
by Stefan Tauner 16 Jun '14
by Stefan Tauner 16 Jun '14
16 Jun '14
On Mon, 12 May 2014 11:52:24 +0200
Ricardo Ribalda Delgado <ricardo.ribalda(a)gmail.com> wrote:
> On Sun, May 11, 2014 at 11:14 PM, Stefan Tauner
> <stefan.tauner(a)alumni.tuwien.ac.at> wrote:
> > On Thu, 5 Sep 2013 15:45:07 +0200
> > Ricardo Ribalda Delgado <ricardo.ribalda(a)gmail.com> wrote:
> >
> >
> > This probably means that we want to copy parts of the copyright lines
> > from those files here. I don't care too much about this, but
> > Carl-Daniel probably does and it would be the right thing™ to do. The
> > least effort would be to copy them all... Carl-Daniel, what do you
> > think? For now I have only added myself for the opaque programmer
> > implementation in ichspi.c and my changes today.
>
> That depends how you handle copyright on your project. The "based on"
> declaration it is usually enough.
> The author line it is generally used to specify who to cc on a bug/patch.
It's totally OK for me, but Carl-Daniel is rather picky about these
things.
> >> +
> >> +/* EEPROM/Flash Control & Data Register */
> >> +#define EECD 0x10
> >
> > Where does the D in EECD comes from? My datasheet denotes it EEC only.
>
> To be consistent with the names of the other parts of flashrom. Just
> in case in the future you want to add a big define for all the intel
> cards. The kernel does this:
>
> driver/ethernet/intel/e1000/e1000_hw.h
Ah! I did not notice that the registers of the older cards are almost
the same (although the supported eeproms are different).
I'll use the names of the respective datasheet nevertheless in this
case.
> >> +const struct dev_entry nics_intel_ee[] = {
> >> + {PCI_VENDOR_ID_INTEL, 0x150e, OK, "Intel", "82580 Quad/Dual Gigabit Ethernet LAN Controller"},
> >> + {PCI_VENDOR_ID_INTEL, UNPROG_DEVICE, OK, "Intel", "Unprogrammed 82580 Quad/Dual Gigabit Ethernet LAN Controller"},
> >
> > Should we include more than this? First of all the devices that were
> > tested by others, but also untested devices that should actually work.
>
> I would recommend only adding tested devices, but it is your call.
That would require the user to recompile flashrom without gain. We use
the OK, NT etc. enum values to indicate if the device has been tested. I
have added the other device IDs mentioned in the datasheet.
> >> + {0},
> >> +};
> >> +
> >> +static int nicintel_ee_probe(struct flashctx *flash)
> >> +{
> >> + if (nicintel_pci->device_id == UNPROG_DEVICE)
> >> + flash->chip->total_size = 16;
> >
> > Why is this a special case? AFAICS this default ID is given if no
> > EEPROM is attached although I guess one could store exactly this ID in
> > the EEPROM too? UNPROG seems to indicate that this is also set for
> > empty EEPROMs. Isn't this dead code in case no EEPROM is attached due o
> > the check for EE_PRES in the init function? And why doesn't the probe
> > fail but defaults to 16kB instead? I seem to neither understand Intel's
> > auto-detection of the EEPROM size nor your interpretation.
>
> The intel card recognizes the eeprom size based on the eeprom content:
> Word 0x12, bit 13:10
>
> A device shows itself as UNPROG_DEVICE if the eeprom content is wrong or empty.
>
> In that case we have to default to the smallest size supported by the
> card : 16 Kbytes
OK, thanks, that makes sense. I have added an appropriate comments to
the probe function and a reference to 3.3.1.5. OTOH, I am not convinced
yet, that an unset EE_PRES bit is a complete show stopper yet. The
description in 3.3.1.5 is either unrelated to EE_PRES or at least one
of the descriptions (EE_PRES or 3.3.15) is wrong, because they
contradict themselves IMHO.
While viewing the datasheet I have also noticed 4.7 which seems to have
been ignored so far. I'll assume our module works nevertheless, but I
have added a FIXME comment.
>
> As fas as I know it is impossible to auto detect the size of an
> eeprom. (unless you write to it)
At least for those in questions this seems to be true.
> >> +#define RETRIES_EERD 10000000
> >
> > How did you obtain all retry values?
>
> Trial and error.
Fair enough but it should be documented :)
> >> + /* Automatic restore of EECD on shutdown is not possible because EECD
> >> + * does not only contain EE_REQ but other bits with side effects as well.
> >> + * Those other bits must be left untouched.
> >> + */
> >
> > This is actually not true. We can of course store the state of the bits
> > we want to restore and use that in a shutdown function that only
> > restores these bits. I have implemented this in my patch for the bit
> > banging output pins/bits and EE_REQ.
>
> Then please also do the same on nicintel_spi.c :P
Well, the comment in nicintel_spi.c is referring to the
pci_*r*mmio_writel functions that tidy up after themselves. The
"semi-automatic" approach using registered shutdown functions works of
course (and that's what implemented there too already). The only
difference is that they unconditionally disable flash access there
while we restored exactly the original state of the bits in question.
> >
> >> + if (dev->device_id != UNPROG_DEVICE) {
> >
> > And why this distinction again?
>
> When the device does not have an eeprom/checksum is wrong, the EE_PRES
> bit is not reliable
Understood, thank you.
> I have made some trivial changes on the code and added the manpage entry.
I had to revert a number of them again. We do use a line length of 112
characters, and I personally detest c89 variable declarations w/o good
reason but prefer tighter scopes. Some of them made sense nevertheless,
thanks.
> I have also tested the code on my board and it looks ok. I have sended
> the patch with git send-email
Great, thanks. As the first EEPROM-accessing flashrom module it
deserves its own section in the manpage and I also want to warn about
possible breakage if EEPROM values become invalid for the NIC. I'll add
a dedicated section to the manpage and commit it sometime this week if
Carl-Daniel does not object. Thanks for all your efforts and patience.
--
Kind regards/Mit freundlichen Grüßen, Stefan Tauner
2
2
Add support for EEPROMs with 1 byte granularity and implicit erase on
write. flashrom will not try to erase before write on these chips.
Explicitly requested erase is done by writing 0xff.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Index: flashrom-no_implicit_erase/flash.h
===================================================================
--- flashrom-no_implicit_erase/flash.h (Revision 1821)
+++ flashrom-no_implicit_erase/flash.h (Arbeitskopie)
@@ -87,6 +87,7 @@
write_gran_528bytes, /* If less than 528 bytes are written, the unwritten bytes are undefined. */
write_gran_1024bytes, /* If less than 1024 bytes are written, the unwritten bytes are undefined. */
write_gran_1056bytes, /* If less than 1056 bytes are written, the unwritten bytes are undefined. */
+ write_gran_1byte_implicit_erase, /* EEPROMs and other chips with implicit erase and 1-byte writes. */
};
/*
Index: flashrom-no_implicit_erase/flashrom.c
===================================================================
--- flashrom-no_implicit_erase/flashrom.c (Revision 1821)
+++ flashrom-no_implicit_erase/flashrom.c (Arbeitskopie)
@@ -766,6 +766,10 @@
case write_gran_1056bytes:
result = need_erase_gran_bytes(have, want, len, 1056);
break;
+ case write_gran_1byte_implicit_erase:
+ /* Do not erase, handle content changes from anything->0xff by writing 0xff. */
+ result = 0;
+ break;
default:
msg_cerr("%s: Unsupported granularity! Please report a bug at "
"flashrom(a)flashrom.org\n", __func__);
@@ -807,6 +811,7 @@
switch (gran) {
case write_gran_1bit:
case write_gran_1byte:
+ case write_gran_1byte_implicit_erase:
stride = 1;
break;
case write_gran_256bytes:
--
http://www.hailfinger.org/
1
1
Author: hailfinger
Date: Tue Jun 17 00:36:17 2014
New Revision: 1822
URL: http://flashrom.org/trac/flashrom/changeset/1822
Log:
EEPROM support: handle implicit erase
Add support for EEPROMs with 1 byte granularity and implicit erase on
write. flashrom will not try to erase before write on these chips.
Explicitly requested erase with -E is done by writing 0xff.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
Modified:
trunk/flash.h
trunk/flashrom.c
Modified: trunk/flash.h
==============================================================================
--- trunk/flash.h Fri Jun 13 00:57:36 2014 (r1821)
+++ trunk/flash.h Tue Jun 17 00:36:17 2014 (r1822)
@@ -87,6 +87,7 @@
write_gran_528bytes, /* If less than 528 bytes are written, the unwritten bytes are undefined. */
write_gran_1024bytes, /* If less than 1024 bytes are written, the unwritten bytes are undefined. */
write_gran_1056bytes, /* If less than 1056 bytes are written, the unwritten bytes are undefined. */
+ write_gran_1byte_implicit_erase, /* EEPROMs and other chips with implicit erase and 1-byte writes. */
};
/*
Modified: trunk/flashrom.c
==============================================================================
--- trunk/flashrom.c Fri Jun 13 00:57:36 2014 (r1821)
+++ trunk/flashrom.c Tue Jun 17 00:36:17 2014 (r1822)
@@ -766,6 +766,10 @@
case write_gran_1056bytes:
result = need_erase_gran_bytes(have, want, len, 1056);
break;
+ case write_gran_1byte_implicit_erase:
+ /* Do not erase, handle content changes from anything->0xff by writing 0xff. */
+ result = 0;
+ break;
default:
msg_cerr("%s: Unsupported granularity! Please report a bug at "
"flashrom(a)flashrom.org\n", __func__);
@@ -807,6 +811,7 @@
switch (gran) {
case write_gran_1bit:
case write_gran_1byte:
+ case write_gran_1byte_implicit_erase:
stride = 1;
break;
case write_gran_256bytes:
1
0
flashrom v0.9.5.2-r1546 on Linux 3.2.0-4-686-pae (i686)
flashrom is free software, get the source code at http://www.flashrom.org
flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian
Command line (1 args): flashrom -V
Calibrating delay loop... OS timer resolution is 2 usecs, 498M loops
per second, delay more than 10% too short (got 45% of expected delay),
recalculating... 501M loops per second, delay more than 10% too short
(got 46% of expected delay), recalculating... 499M loops per second,
delay more than 10% too short (got 45% of expected delay),
recalculating... 500M loops per second, delay more than 10% too short
(got 45% of expected delay), recalculating... 500M loops per second,
delay loop is unreliable, trying to continue 10 myus = 6 us, 100 myus
= 51 us, 1000 myus = 542 us, 10000 myus = 5043 us, 8 myus = 5 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "CdcPointSpa"
DMI string system-product-name: "System Name"
DMI string system-version: "System Version"
DMI string baseboard-manufacturer: "ASUSTeK Computer INC."
DMI string baseboard-product-name: "P4B-M "
DMI string baseboard-version: "REV 1.xx"
DMI string chassis-type: "Tower"
W836xx enter config mode worked or we were already in config mode.
W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: 87.
Please send the output of "flashrom -V" to
flashrom(a)flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
Found ITE Super I/O, ID 0x8708 on port 0x2e
Found chipset "Intel ICH2" with PCI ID 8086:2440. Enabling flash write...
BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0
OK.
Super I/O ID 0x8708 is not on the list of flash capable controllers.
Disabling flash write protection for board "ASUS P4B266"...
Intel ICH LPC bridge: Raising GPIO22.
OK.
The following protocols are supported: FWH.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x25, id2
0x1e, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x25, id2 0x1e,
id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2
0xff, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57
Found SST flash chip "SST49LF002A/B" (256 kB, FWH) at physical address
0xfffc0000.
Lock status for 0x000000 (size 0x004000) is 01, write locked
Lock status for 0x004000 (size 0x004000) is 00, full access
Lock status for 0x008000 (size 0x004000) is 01, write locked
Lock status for 0x00c000 (size 0x004000) is 00, full access
Lock status for 0x010000 (size 0x004000) is 01, write locked
Lock status for 0x014000 (size 0x004000) is 00, full access
Lock status for 0x018000 (size 0x004000) is 01, write locked
Lock status for 0x01c000 (size 0x004000) is 00, full access
Lock status for 0x020000 (size 0x004000) is 01, write locked
Lock status for 0x024000 (size 0x004000) is 00, full access
Lock status for 0x028000 (size 0x004000) is 01, write locked
Lock status for 0x02c000 (size 0x004000) is 00, full access
Lock status for 0x030000 (size 0x004000) is 01, write locked
Lock status for 0x034000 (size 0x004000) is 00, full access
Lock status for 0x038000 (size 0x004000) is 01, write locked
Lock status for 0x03c000 (size 0x004000) is 00, full access
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x25, id2
0x1e, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff,
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2
0xff, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2
0xff, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x25, id2 0x1e,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x25, id2 0x1e,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x25, id2 0x1e,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x25, id2 0x1e,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff,
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common:
id1 0xbf, id2 0x57
Found SST flash chip "SST49LF002A/B" (256 kB, FWH).
No operations were specified.
Restoring PCI config space for 00:1f:0 reg 0x4e
--
Daniele Forsi
1
0
Some important facts:
- AT45 prober issues a 0xD7 opcode (without address) unconditionally.
- No prober weights yet - any chip matched by a single prober is
presented to the user.
Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
---
82802ab.c | 49 +-
Makefile | 2 +-
at45db.c | 48 +-
chipdrivers.h | 36 +-
cli_classic.c | 132 ++-
en29lv640b.c | 27 +-
flash.h | 54 +-
flashchips.c | 3624 +++++++++++++++++++++++++++++++++------------------------
flashchips.h | 888 +++++++-------
flashrom.c | 374 ++++--
ichspi.c | 52 +-
jedec.c | 122 +-
m29f400bt.c | 23 +-
opaque.c | 22 +-
print.c | 13 +-
print_wiki.c | 11 -
programmer.c | 2 +-
programmer.h | 5 +-
sfdp.c | 109 +-
spi25.c | 281 +----
stm50.c | 2 +-
w29ee011.c | 37 +-
22 files changed, 3270 insertions(+), 2643 deletions(-)
diff --git a/82802ab.c b/82802ab.c
index d249c3a..5b376ce 100644
--- a/82802ab.c
+++ b/82802ab.c
@@ -40,10 +40,9 @@ void print_status_82802ab(uint8_t status)
msg_cdbg("%s", status & 0x2 ? "WP|TBL#|WP#,ABORT:" : "UNLOCK:");
}
-static int probe_82802ab(struct flashctx *flash, bool shifted)
+static int probe_82802ab(struct flashctx *flash, struct probe_res *res, bool shifted)
{
chipaddr bios = flash->virtual_memory;
- uint8_t id1, id2, flashcontent1, flashcontent2;
/* Reset to get a clean state */
chip_writeb(flash, 0xFF, bios);
@@ -53,47 +52,37 @@ static int probe_82802ab(struct flashctx *flash, bool shifted)
chip_writeb(flash, 0x90, bios);
programmer_delay(10);
- id1 = chip_readb(flash, bios + (0x00 << shifted));
- id2 = chip_readb(flash, bios + (0x01 << shifted));
+#if (NUM_PROBE_BYTES < 2)
+#error probe_82802ab requires NUM_PROBE_BYTES to be at least 2.
+#endif
+ res->vals[0] = chip_readb(flash, bios + (0x00 << shifted));
+ res->vals[1] = chip_readb(flash, bios + (0x01 << shifted));
/* Leave ID mode */
chip_writeb(flash, 0xFF, bios);
programmer_delay(10);
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x", __func__, id1, id2);
-
- if (!oddparity(id1))
- msg_cdbg(", id1 parity violation");
-
- /*
- * Read the product ID location again. We should now see normal
- * flash contents.
- */
- flashcontent1 = chip_readb(flash, bios + (0x00 << shifted));
- flashcontent2 = chip_readb(flash, bios + (0x01 << shifted));
-
- if (id1 == flashcontent1)
- msg_cdbg(", id1 is normal flash content");
- if (id2 == flashcontent2)
- msg_cdbg(", id2 is normal flash content");
-
- msg_cdbg("\n");
- if (id1 != flash->chip->manufacture_id || id2 != flash->chip->model_id)
+ uint8_t cont[2];
+ cont[0] = chip_readb(flash, bios + (0x00 << shifted));
+ cont[1] = chip_readb(flash, bios + (0x01 << shifted));
+ if (test_for_valid_ids(res->vals, cont, 2)) {
+ res->len = 2;
+ return 1;
+ } else {
+ res->len = 0;
return 0;
-
-
- return 1;
+ }
}
-int probe_82802ab_shifted(struct flashctx *flash)
+int probe_82802ab_shifted(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- return probe_82802ab(flash, true);
+ return probe_82802ab(flash, res, true);
}
-int probe_82802ab_unshifted(struct flashctx *flash)
+int probe_82802ab_unshifted(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- return probe_82802ab(flash, false);
+ return probe_82802ab(flash, res, false);
}
/* FIXME: needs timeout */
diff --git a/Makefile b/Makefile
index 7a48889..4500b5e 100644
--- a/Makefile
+++ b/Makefile
@@ -35,7 +35,7 @@ INSTALL = install
DIFF = diff
PREFIX ?= /usr/local
MANDIR ?= $(PREFIX)/share/man
-CFLAGS ?= -Os -Wall -Wshadow
+CFLAGS ?= -Os -Wall -Wshadow -g
EXPORTDIR ?= .
AR ?= ar
RANLIB ?= ranlib
diff --git a/at45db.c b/at45db.c
index 5396d7f..1150d3a 100644
--- a/at45db.c
+++ b/at45db.c
@@ -170,48 +170,26 @@ int spi_prettyprint_status_register_at45db(struct flashctx *flash)
return 0;
}
-/* Probe function for AT45DB* chips that support multiple page sizes. */
-int probe_spi_at45db(struct flashctx *flash)
+/* Probe function for AT45DB* chips that support multiple page sizes. In order to tell which page size a chip
+ * has we need to read the status register and investigate bit #0. */
+int probe_spi_at45db(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
{
- uint8_t status;
- struct flashchip *chip = flash->chip;
+#if (NUM_PROBE_BYTES < 1)
+#error probe_spi_at45db requires NUM_PROBE_BYTES to be at least 1.
+#endif
- if (!probe_spi_rdid(flash))
- return 0;
+ if (res_len == 0)
+ return -1;
- /* Some AT45DB* chips support two different page sizes each (e.g. 264 and 256 B). In order to tell which
- * page size this chip has we need to read the status register. */
+ uint8_t status;
if (at45db_read_status_register(flash, &status) != 0)
- return 0;
-
- /* We assume sane power-of-2 page sizes and adjust the chip attributes in case this is not the case. */
- if ((status & AT45DB_POWEROF2) == 0) {
- chip->total_size = (chip->total_size / 32) * 33;
- chip->page_size = (chip->page_size / 32) * 33;
-
- unsigned int i, j;
- for (i = 0; i < NUM_ERASEFUNCTIONS; i++) {
- struct block_eraser *eraser = &chip->block_erasers[i];
- for (j = 0; j < NUM_ERASEREGIONS; j++) {
- eraser->eraseblocks[j].size = (eraser->eraseblocks[j].size / 32) * 33;
- }
- }
- }
+ return -1;
- switch (chip->page_size) {
- case 256: chip->gran = write_gran_256bytes; break;
- case 264: chip->gran = write_gran_264bytes; break;
- case 512: chip->gran = write_gran_512bytes; break;
- case 528: chip->gran = write_gran_528bytes; break;
- case 1024: chip->gran = write_gran_1024bytes; break;
- case 1056: chip->gran = write_gran_1056bytes; break;
- default:
- msg_cerr("%s: unknown page size %d.\n", __func__, chip->page_size);
+ if (status == 0xFF || status == 0x00)
return 0;
- }
-
- msg_cdbg2("%s: total size %i kB, page size %i B\n", __func__, chip->total_size * 1024, chip->page_size);
+ res->vals[0] = status & AT45DB_POWEROF2;
+ res->len = 1;
return 1;
}
diff --git a/chipdrivers.h b/chipdrivers.h
index 11a7191..668bd00 100644
--- a/chipdrivers.h
+++ b/chipdrivers.h
@@ -33,13 +33,10 @@ int spi_chip_write_256(struct flashctx *flash, const uint8_t *buf, unsigned int
int spi_chip_read(struct flashctx *flash, uint8_t *buf, unsigned int start, int unsigned len);
/* spi25.c */
-int probe_spi_rdid(struct flashctx *flash);
-int probe_spi_rdid4(struct flashctx *flash);
-int probe_spi_rems(struct flashctx *flash);
-int probe_spi_res1(struct flashctx *flash);
-int probe_spi_res2(struct flashctx *flash);
-int probe_spi_res3(struct flashctx *flash);
-int probe_spi_at25f(struct flashctx *flash);
+int probe_spi_rdid(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_spi_rems(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_spi_res(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_spi_at25f(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
int spi_write_enable(struct flashctx *flash);
int spi_write_disable(struct flashctx *flash);
int spi_block_erase_20(struct flashctx *flash, unsigned int addr, unsigned int blocklen);
@@ -108,12 +105,12 @@ int probe_spi_sfdp(struct flashctx *flash);
/* opaque.c */
int probe_opaque(struct flashctx *flash);
-int read_opaque(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
-int write_opaque(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
-int erase_opaque(struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen);
+
+/* flashrom.c */
+int probe_allsizes(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p);
/* at45db.c */
-int probe_spi_at45db(struct flashctx *flash);
+int probe_spi_at45db(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p);
int spi_prettyprint_status_register_at45db(struct flashctx *flash);
int spi_disable_blockprotect_at45db(struct flashctx *flash);
int spi_read_at45db(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
@@ -127,8 +124,8 @@ int spi_erase_at45cs_sector(struct flashctx *flash, unsigned int addr, unsigned
/* 82802ab.c */
uint8_t wait_82802ab(struct flashctx *flash);
-int probe_82802ab_shifted(struct flashctx *flash);
-int probe_82802ab_unshifted(struct flashctx *flash);
+int probe_82802ab_shifted(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_82802ab_unshifted(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
int erase_block_82802ab(struct flashctx *flash, unsigned int page, unsigned int pagesize);
int write_82802ab(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
void print_status_82802ab(uint8_t status);
@@ -138,9 +135,14 @@ int unlock_lh28f008bjt(struct flashctx *flash);
/* jedec.c */
uint8_t oddparity(uint8_t val);
+bool test_for_valid_ids(uint8_t *ids, uint8_t *content, unsigned int len);
void toggle_ready_jedec(const struct flashctx *flash, chipaddr dst);
void data_polling_jedec(const struct flashctx *flash, chipaddr dst, uint8_t data);
-int probe_jedec(struct flashctx *flash);
+int probe_jedec_longreset(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_jedec_shortreset_full(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_jedec_shortreset_full_384(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_jedec_shortreset_aaa(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
+int probe_jedec_shortreset_2aa(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
int write_jedec(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
int write_jedec_1(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
int erase_sector_jedec(struct flashctx *flash, unsigned int page, unsigned int pagesize);
@@ -148,7 +150,7 @@ int erase_block_jedec(struct flashctx *flash, unsigned int page, unsigned int bl
int erase_chip_block_jedec(struct flashctx *flash, unsigned int page, unsigned int blocksize);
/* m29f400bt.c */
-int probe_m29f400bt(struct flashctx *flash);
+int probe_m29f400bt(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
int write_m29f400bt(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
void protect_m29f400bt(struct flashctx *flash, chipaddr bios);
@@ -190,7 +192,7 @@ int unlock_w39v080fa(struct flashctx *flash);
int printlock_at49f(struct flashctx *flash);
/* w29ee011.c */
-int probe_w29ee011(struct flashctx *flash);
+int probe_w29ee011(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
/* stm50.c */
int erase_sector_stm50(struct flashctx *flash, unsigned int block, unsigned int blocksize);
@@ -198,7 +200,7 @@ int unlock_stm50_uniform(struct flashctx *flash);
int unlock_stm50_nonuniform(struct flashctx *flash);
/* en29lv640b.c */
-int probe_en29lv640b(struct flashctx *flash);
+int probe_en29lv640b(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2);
int erase_block_shifted_jedec(struct flashctx *flash, unsigned int start, unsigned int len);
int erase_chip_block_shifted_jedec(struct flashctx *flash, unsigned int start, unsigned int len);
int write_en29lv640b(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
diff --git a/cli_classic.c b/cli_classic.c
index db76fbc..9068dc7 100644
--- a/cli_classic.c
+++ b/cli_classic.c
@@ -158,13 +158,9 @@ static void check_chip_supported(const struct flashchip *chip)
int main(int argc, char *argv[])
{
- /* Probe for up to three flash chips. */
- const struct flashchip *chip = NULL;
- struct flashctx flashes[3] = {{0}};
- struct flashctx *fill_flash;
const char *name;
- int namelen, opt, i, j;
- int startchip = -1, chipcount = 0, option_index = 0, force = 0;
+ int namelen, opt, i;
+ int option_index = 0, force = 0;
#if CONFIG_PRINT_WIKI == 1
int list_supported_wiki = 0;
#endif
@@ -445,6 +441,7 @@ int main(int argc, char *argv[])
ret = 1;
goto out;
}
+ const struct flashchip *chip = NULL;
/* Does a chip with the requested name exist in the flashchips array? */
if (chip_to_probe) {
for (chip = flashchips; chip && chip->name; chip++)
@@ -492,84 +489,91 @@ int main(int argc, char *argv[])
msg_pdbg("The following protocols are supported: %s.\n", tempstr);
free(tempstr);
- for (j = 0; j < registered_programmer_count; j++) {
- startchip = 0;
- while (chipcount < ARRAY_SIZE(flashes)) {
- startchip = probe_flash(®istered_programmers[j], startchip, &flashes[chipcount], 0);
- if (startchip == -1)
- break;
- chipcount++;
- startchip++;
- }
+ /* Probe for up to three flash chips. */
+ struct flashctx *flashes = NULL;
+ int chipcount = probe_flash(&flashes, NULL);
+ if (chipcount < 0) {
+ msg_cerr("Error: Probing for flash chips failed.\n");
+ ret = 1;
+ goto out_free_flashes;
}
- if (chipcount > 1) {
- msg_cinfo("Multiple flash chip definitions match the detected chip(s): \"%s\"",
- flashes[0].chip->name);
- for (i = 1; i < chipcount; i++)
- msg_cinfo(", \"%s\"", flashes[i].chip->name);
- msg_cinfo("\nPlease specify which chip definition to use with the -c <chipname> option.\n");
- ret = 1;
- goto out_shutdown;
- } else if (!chipcount) {
+ struct flashctx *flash;
+ if (chipcount == 0) {
msg_cinfo("No EEPROM/flash device found.\n");
if (!force || !chip_to_probe) {
msg_cinfo("Note: flashrom can never write if the flash chip isn't found "
"automatically.\n");
}
if (force && read_it && chip_to_probe) {
- struct registered_programmer *pgm;
int compatible_programmers = 0;
msg_cinfo("Force read (-f -r -c) requested, pretending the chip is there:\n");
- /* This loop just counts compatible controllers. */
+ flash = malloc(sizeof(struct flashctx));
+ if (flash == NULL) {
+ msg_cerr("Out of memory!\n");
+ ret = 1;
+ goto out_free_flashes;
+ }
+ /* chip is still set from the chip_to_probe check earlier in this function. */
+ flash->chip = chip;
+ unsigned int j;
for (j = 0; j < registered_programmer_count; j++) {
- pgm = ®istered_programmers[j];
- /* chip is still set from the chip_to_probe earlier in this function. */
- if (pgm->buses_supported & chip->bustype)
+ flash->pgm = ®istered_programmers[j];
+ if (flash->pgm->buses_supported & chip->bustype)
compatible_programmers++;
}
if (!compatible_programmers) {
msg_cinfo("No compatible controller found for the requested flash chip.\n");
ret = 1;
- goto out_shutdown;
+ goto out_free_flashes;
}
if (compatible_programmers > 1)
msg_cinfo("More than one compatible controller found for the requested flash "
"chip, using the first one.\n");
- for (j = 0; j < registered_programmer_count; j++) {
- pgm = ®istered_programmers[j];
- startchip = probe_flash(pgm, 0, &flashes[0], 1);
- if (startchip != -1)
- break;
- }
- if (startchip == -1) {
- // FIXME: This should never happen! Ask for a bug report?
- msg_cinfo("Probing for flash chip '%s' failed.\n", chip_to_probe);
- ret = 1;
- goto out_shutdown;
- }
msg_cinfo("Please note that forced reads most likely contain garbage.\n");
- ret = read_flash_to_file(&flashes[0], filename);
- free(flashes[0].chip);
- goto out_shutdown;
+ ret = read_flash_to_file(flash, filename);
+ free(flash);
+ goto out_free_flashes;
+ } else {
+ ret = 1;
+ goto out_free_flashes;
}
- ret = 1;
- goto out_shutdown;
- } else if (!chip_to_probe) {
- /* repeat for convenience when looking at foreign logs */
- tempstr = flashbuses_to_text(flashes[0].chip->bustype);
- msg_gdbg("Found %s flash chip \"%s\" (%d kB, %s).\n",
- flashes[0].chip->vendor, flashes[0].chip->name, flashes[0].chip->total_size, tempstr);
- free(tempstr);
- }
+ } else if (chipcount == 1) {
+ flash = &flashes[0];
+ } else {
+ msg_cinfo("%d flash chip definitions match the genuine chip: ", chipcount);
- fill_flash = &flashes[0];
+ msg_cinfo("\"%s\"", flashes[0].chip->name);
+ for (i = 1; i < chipcount; i++)
+ msg_cinfo(", \"%s\"", flashes[i].chip->name);
+
+ msg_cinfo("\n");
+ if (chip_to_probe == NULL) {
+ msg_cinfo("Please specify which chip definition to use with the "
+ "--chip/-c <chipname> option.\n");
+ ret = 1;
+ goto out_free_flashes;
+ }
+ for (i = 0; i < chipcount; i++) {
+ if (strcmp(flashes[i].chip->name, chip_to_probe) == 0) {
+ flash = &flashes[i];
+ msg_cinfo("Using %s as requested.\n", flash->chip->name);
+ break;
+ }
+ }
+ if (flash == NULL) {
+ msg_cerr("The chip supplied with the --chip/-c option was not detected automatically.\n"
+ "You can enforce using it with the --force/-f option.\n");
+ ret = 1;
+ goto out_free_flashes;
+ }
+ }
- check_chip_supported(fill_flash->chip);
+ check_chip_supported(flash->chip);
- unsigned int limitexceeded = count_max_decode_exceedings(fill_flash);
+ unsigned int limitexceeded = count_max_decode_exceedings(flash);
if (limitexceeded > 0 && !force) {
- enum chipbustype commonbuses = fill_flash->pgm->buses_supported & fill_flash->chip->bustype;
+ enum chipbustype commonbuses = flash->pgm->buses_supported & flash->chip->bustype;
/* Sometimes chip and programmer have more than one bus in common,
* and the limit is not exceeded on all buses. Tell the user. */
@@ -580,12 +584,12 @@ int main(int argc, char *argv[])
msg_cerr("This flash chip is too big for this programmer (--verbose/-V gives details).\n"
"Use --force/-f to override at your own risk.\n");
ret = 1;
- goto out_shutdown;
+ goto out_free_flashes;
}
if (!(read_it | write_it | verify_it | erase_it)) {
msg_ginfo("No operations were specified.\n");
- goto out_shutdown;
+ goto out_free_flashes;
}
/* Always verify write operations unless -n is used. */
@@ -597,13 +601,15 @@ int main(int argc, char *argv[])
* Give the chip time to settle.
*/
programmer_delay(100000);
- ret |= doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it);
+ ret |= doit(flash, force, filename, read_it, write_it, erase_it, verify_it);
+out_free_flashes:
+ free(flashes);
out_shutdown:
programmer_shutdown();
out:
- for (i = 0; i < chipcount; i++)
- free(flashes[i].chip);
+ //for (i = 0; i < chipcount; i++)
+ //free(flashes[i]->chip);
layout_cleanup();
free(filename);
diff --git a/en29lv640b.c b/en29lv640b.c
index a274f62..47da1a1 100644
--- a/en29lv640b.c
+++ b/en29lv640b.c
@@ -58,10 +58,9 @@ int write_en29lv640b(struct flashctx *flash, const uint8_t *src, unsigned int st
return 0;
}
-int probe_en29lv640b(struct flashctx *flash)
+int probe_en29lv640b(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
chipaddr bios = flash->virtual_memory;
- uint16_t id1, id2;
chip_writeb(flash, 0xAA, bios + 0xAAA);
chip_writeb(flash, 0x55, bios + 0x555);
@@ -69,21 +68,29 @@ int probe_en29lv640b(struct flashctx *flash)
programmer_delay(10);
- id1 = chip_readb(flash, bios + 0x200);
- id1 |= (chip_readb(flash, bios) << 8);
+#if (NUM_PROBE_BYTES < 3)
+#error probe_en29lv640b requires NUM_PROBE_BYTES to be at least 3.
+#endif
+ res->vals[0] = chip_readb(flash, bios + 0x200);
+ res->vals[1] = chip_readb(flash, bios);
- id2 = chip_readb(flash, bios + 0x02);
+ res->vals[2] = chip_readb(flash, bios + 0x02);
chip_writeb(flash, 0xF0, bios + 0xAAA);
-
programmer_delay(10);
- msg_cdbg("%s: id1 0x%04x, id2 0x%04x\n", __func__, id1, id2);
+ uint8_t cont[3];
+ cont[0] = chip_readb(flash, bios + 0x200);
+ cont[1] = chip_readb(flash, bios);
+ cont[2] = chip_readb(flash, bios + 0x02);
- if (id1 == flash->chip->manufacture_id && id2 == flash->chip->model_id)
+ if (test_for_valid_ids(res->vals, cont, 3)) {
+ res->len = 3;
return 1;
-
- return 0;
+ } else {
+ res->len = 0;
+ return 0;
+ }
}
static int erase_chip_shifted_jedec(struct flashctx *flash)
diff --git a/flash.h b/flash.h
index d26d90b..ed0aeeb 100644
--- a/flash.h
+++ b/flash.h
@@ -53,6 +53,7 @@ typedef uint32_t chipsize_t; /* Able to store the number of bytes of any support
#define PRIxCHIPADDR "06"PRIx32
#define PRIuCHIPSIZE PRIu32
+int shutdown_free(void *data);
int register_shutdown(int (*function) (void *data), void *data);
void *programmer_map_flash_region(const char *descr, uintptr_t phys_addr, size_t len);
void programmer_unmap_flash_region(void *virt_addr, size_t len);
@@ -140,8 +141,36 @@ enum test_state {
#define TEST_BAD_PRE (struct tested){ .probe = BAD, .read = BAD, .erase = BAD, .write = NT }
#define TEST_BAD_PREW (struct tested){ .probe = BAD, .read = BAD, .erase = BAD, .write = BAD }
+
+#define NUM_PROBES 3
+#define NUM_PROBE_BYTES 5 /* Values below 2 will break code. */
+
struct flashctx;
-typedef int (erasefunc_t)(struct flashctx *flash, unsigned int addr, unsigned int blocklen);
+struct registered_programmer; /* programmer.h */
+struct probe;
+struct probe_res;
+
+/* fixme */
+typedef int (probefunc_t)(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p);
+
+typedef struct probe_res {
+ uint8_t len;
+ uint8_t vals[NUM_PROBE_BYTES];
+ probefunc_t *probe_func;
+ unsigned int chip_size; /* in kB */
+} probe_res;
+
+typedef struct probe {
+ probefunc_t *probe_func;
+ enum chipbustype bustype;
+ const char *mnemonic;
+ uint16_t size_min;
+ uint16_t size_max;
+ uint8_t size_step;
+} probe;
+
+/* An erase function should try to erase one block of size 'len' at address 'addr' and return 0 on success. */
+typedef int (erasefunc_t)(struct flashctx *flash, unsigned int addr, unsigned int len);
struct flashchip {
const char *vendor;
@@ -149,14 +178,6 @@ struct flashchip {
enum chipbustype bustype;
- /*
- * With 32bit manufacture_id and model_id we can cover IDs up to
- * (including) the 4th bank of JEDEC JEP106W Standard Manufacturer's
- * Identification code.
- */
- uint32_t manufacture_id;
- uint32_t model_id;
-
/* Total chip size in kilobytes */
unsigned int total_size;
/* Chip page size in bytes */
@@ -171,7 +192,10 @@ struct flashchip {
enum test_state write;
} tested;
- int (*probe) (struct flashctx *flash);
+ struct prober {
+ probefunc_t *func;
+ struct probe_res res;
+ } probers[NUM_PROBES];
/*
* Erase blocks and associated erase function. Any chip erase function
@@ -185,9 +209,7 @@ struct flashchip {
unsigned int size; /* Eraseblock size in bytes */
unsigned int count; /* Number of contiguous blocks with that size */
} eraseblocks[NUM_ERASEREGIONS];
- /* a block_erase function should try to erase one block of size
- * 'blocklen' at address 'blockaddr' and return 0 on success. */
- int (*block_erase) (struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen);
+ erasefunc_t *block_erase;
} block_erasers[NUM_ERASEFUNCTIONS];
int (*printlock) (struct flashctx *flash);
@@ -202,7 +224,7 @@ struct flashchip {
};
struct flashctx {
- struct flashchip *chip;
+ const struct flashchip *chip;
chipaddr virtual_memory;
/* Some flash devices have an additional register space. */
chipaddr virtual_registers;
@@ -241,7 +263,7 @@ extern const char flashrom_version[];
extern const char *chip_to_probe;
int read_memmapped(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
int erase_flash(struct flashctx *flash);
-int probe_flash(struct registered_programmer *pgm, int startchip, struct flashctx *fill_flash, int force);
+int probe_flash(struct flashctx **flashes, const struct registered_programmer *pgm);
int read_flash_to_file(struct flashctx *flash, const char *filename);
char *extract_param(const char *const *haystack, const char *needle, const char *delim);
int verify_range(struct flashctx *flash, const uint8_t *cmpbuf, unsigned int start, unsigned int len);
@@ -327,5 +349,7 @@ int spi_send_command(struct flashctx *flash, unsigned int writecnt, unsigned int
int spi_send_multicommand(struct flashctx *flash, struct spi_command *cmds);
uint32_t spi_get_valid_read_addr(struct flashctx *flash);
+/* programmer.c */
enum chipbustype get_buses_supported(void);
+
#endif /* !__FLASH_H__ */
diff --git a/flashchips.c b/flashchips.c
index 6e6b3a8..18637f5 100644
--- a/flashchips.c
+++ b/flashchips.c
@@ -60,13 +60,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F010A/B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F010B, /* Same as Am29F010A */
.total_size = 128,
.page_size = 16 * 1024,
- .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
+ .feature_bits = FEATURE_ADDR_2AA,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMIC_ID, AMD_AM29F010B } } }, /* Same as Am29F010A */
+ },
.block_erasers =
{
{
@@ -86,13 +87,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F002(N)BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F002BB,
.total_size = 256,
.page_size = 256,
- .feature_bits = FEATURE_SHORT_RESET | FEATURE_ADDR_2AA,
+ .feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29F002BB } } },
+ },
.block_erasers =
{
{
@@ -117,13 +119,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F002(N)BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F002BT,
.total_size = 256,
.page_size = 256,
- .feature_bits = FEATURE_EITHER_RESET | FEATURE_ADDR_2AA,
+ .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29F002BT } } },
+ },
.block_erasers =
{
{
@@ -148,13 +151,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F016D",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F016D,
- .total_size = 2 * 1024,
+ .total_size = 2048,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29F016D } } },
+ },
.block_erasers =
{
{
@@ -174,13 +178,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29F040B } } },
+ },
.block_erasers =
{
{
@@ -200,13 +205,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29F080B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29F080B,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29F080B } } },
+ },
.block_erasers =
{
{
@@ -226,13 +232,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV001BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV001BB,
.total_size = 128,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV001BB } } },
+ },
.block_erasers =
{
{
@@ -256,13 +263,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV001BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV001BT,
.total_size = 128,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV001BT } } },
+ },
.block_erasers =
{
{
@@ -286,13 +294,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV002BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV002BB,
.total_size = 256,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV002BB } } },
+ },
.block_erasers =
{
{
@@ -317,13 +326,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV002BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV002BT,
.total_size = 256,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV002BT } } },
+ },
.block_erasers =
{
{
@@ -348,13 +358,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV004BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV004BB,
.total_size = 512,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV004BB } } },
+ },
.block_erasers =
{
{
@@ -379,13 +390,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV004BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV004BT,
.total_size = 512,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV004BT } } },
+ },
.block_erasers =
{
{
@@ -410,13 +422,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV008BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV008BB,
.total_size = 1024,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV008BB } } },
+ },
.block_erasers =
{
{
@@ -441,13 +454,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV008BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV008BT,
.total_size = 1024,
.page_size = 64 * 1024, /* unused */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV008BT } } },
+ },
.block_erasers =
{
{
@@ -472,13 +486,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV040B } } },
+ },
.block_erasers =
{
{
@@ -498,13 +513,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMD",
.name = "Am29LV081B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMD_ID,
- .model_id = AMD_AM29LV080B,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET, /* datasheet specifies address as don't care */
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMD_ID, AMD_AM29LV080B } } },
+ },
.block_erasers =
{
{
@@ -524,13 +540,15 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L05PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L05PT,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L05PT } } },
+ { probe_spi_res, { 1, { 0x05 } } },
+ },
.block_erasers =
{
{
@@ -557,13 +575,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L05PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L05PU,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L05PU } } },
+ },
.block_erasers =
{
{
@@ -590,13 +609,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L10PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L10PT,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L10PT } } },
+ },
.block_erasers =
{
{
@@ -624,13 +644,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L10PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L10PU,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L10PU } } },
+ },
.block_erasers =
{
{
@@ -658,13 +679,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L20PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L20PT,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L20PT } } },
+ },
.block_erasers =
{
{
@@ -692,13 +714,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L20PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L20PU,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L20PU } } },
+ },
.block_erasers =
{
{
@@ -731,13 +754,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L40PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L40PT,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L40PT } } },
+ },
.block_erasers =
{
{
@@ -765,13 +789,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L40PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L40PU,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L40PU } } },
+ },
.block_erasers =
{
{
@@ -799,13 +824,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L80P",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L80P,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L80P } } },
+ },
.block_erasers =
{
{
@@ -833,13 +859,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L16PT",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L16PT,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L16PT } } },
+ },
.block_erasers =
{
{
@@ -870,13 +897,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L16PU",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = AMIC_A25L16PU,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid4,
+ .probers =
+ {
+ { probe_spi_rdid, { 4, { AMIC_ID, AMIC_A25L16PU } } },
+ },
.block_erasers =
{
{
@@ -907,13 +935,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L512",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L512 } } },
+ },
.block_erasers =
{
{
@@ -938,13 +967,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L010",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L010 } } },
+ },
.block_erasers =
{
{
@@ -969,13 +999,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L020",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L020 } } },
+ },
.block_erasers =
{
{
@@ -1000,13 +1031,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L040",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L040 } } },
+ },
.block_erasers =
{
{
@@ -1031,13 +1063,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L080",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L080,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L080 } } },
+ },
.block_erasers =
{
{
@@ -1062,13 +1095,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L016",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L016,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L016 } } },
+ },
.block_erasers =
{
{
@@ -1093,14 +1127,15 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25L032",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25L032,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25L032 } } },
+ },
.block_erasers =
{
{
@@ -1131,15 +1166,16 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25LQ16",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ16,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25LQ16 } } },
+ },
.block_erasers = {
{
.eraseblocks = { { 4 * 1024, 512 } },
@@ -1169,15 +1205,16 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25LQ032/A25LQ32A",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ032,
.total_size = 4096,
.page_size = 256,
/* A25LQ32A supports SFDP */
/* OTP: 64B total; read 0x4B, 0x48; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25LQ032 } } },
+ },
.block_erasers =
{
{
@@ -1208,8 +1245,6 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A25LQ64",
.bustype = BUS_SPI,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A25LQ032,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
@@ -1217,7 +1252,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x35, disable 0xF5 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { AMIC_ID_NOPREFIX, AMIC_A25LQ032 } } },
+ },
.block_erasers =
{
{
@@ -1248,13 +1286,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A29002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29002B,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMIC_ID_NOPREFIX, AMIC_A29002B } } },
+ },
.block_erasers =
{
{
@@ -1279,13 +1318,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A29002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMIC_ID_NOPREFIX, AMIC_A29002T } } },
+ },
.block_erasers =
{
{
@@ -1310,13 +1350,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A29040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A29040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { AMIC_ID_NOPREFIX, AMIC_A29040B } } },
+ },
.block_erasers =
{
{
@@ -1336,13 +1377,14 @@ const struct flashchip flashchips[] = {
.vendor = "AMIC",
.name = "A49LF040A",
.bustype = BUS_LPC,
- .manufacture_id = AMIC_ID_NOPREFIX,
- .model_id = AMIC_A49LF040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { AMIC_ID_NOPREFIX, AMIC_A49LF040A } } },
+ },
.block_erasers =
{
{
@@ -1363,14 +1405,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF021",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF021,
.total_size = 256,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF021 } } },
+ },
.block_erasers =
{
{
@@ -1401,13 +1444,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF041A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF041A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF041A } } },
+ },
.block_erasers =
{
{
@@ -1438,13 +1482,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF081",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF081 } } },
+ },
.block_erasers =
{
{
@@ -1475,13 +1520,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF081A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF081A } } },
+ },
.block_erasers =
{
{
@@ -1512,13 +1558,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF161,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF161 } } },
+ },
.block_erasers =
{
{
@@ -1549,13 +1596,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF321",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF321,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF321 } } },
+ },
.block_erasers =
{
{
@@ -1586,14 +1634,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF321A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF321A,
.total_size = 4096,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF321A } } },
+ },
.block_erasers =
{
{
@@ -1624,13 +1673,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DF641(A)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF641,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF641 } } },
+ },
.block_erasers =
{
{
@@ -1661,14 +1711,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DL081",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DF081,
.total_size = 1024,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DF081 } } },
+ },
.block_erasers =
{
{
@@ -1699,14 +1750,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DL161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DL161,
.total_size = 2048,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DL161 } } },
+ },
.block_erasers =
{
{
@@ -1737,14 +1789,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25DQ161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25DQ161,
.total_size = 2048,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25DQ161 } } },
+ },
.block_erasers =
{
{
@@ -1775,13 +1828,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25F512",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ .probers =
+ {
+ { probe_spi_at25f, { 3, { ATMEL_ID, ATMEL_AT25F512 } } },
+ },
.block_erasers =
{
{
@@ -1803,13 +1857,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25F512A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512A,
.total_size = 64,
.page_size = 128,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ .probers =
+ {
+ { probe_spi_at25f, { 3, { ATMEL_ID, ATMEL_AT25F512A } } },
+ },
.block_erasers =
{
{
@@ -1832,14 +1887,15 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25F512B",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F512B,
.total_size = 64,
.page_size = 256,
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25F512B } } },
+ },
.block_erasers =
{
{
@@ -1875,13 +1931,14 @@ const struct flashchip flashchips[] = {
* All other properties seem to be the same.*/
.name = "AT25F1024(A)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F1024,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at25f,
+ .probers =
+ {
+ { probe_spi_at25f, { 3, { ATMEL_ID, ATMEL_AT25F1024 } } },
+ },
.block_erasers =
{
{
@@ -1903,13 +1960,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25F2048",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F2048,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at25f,
+ .probers =
+ {
+ { probe_spi_at25f, { 3, { ATMEL_ID, ATMEL_AT25F2048 } } },
+ },
.block_erasers =
{
{
@@ -1931,13 +1989,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25F4096",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25F4096,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at25f,
+ .probers =
+ {
+ { probe_spi_at25f, { 3, { ATMEL_ID, ATMEL_AT25F4096 } } },
+ },
.block_erasers =
{
{
@@ -1960,13 +2019,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25FS010",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25FS010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25FS010 } } },
+ },
.block_erasers =
{
{
@@ -2000,13 +2060,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT25FS040",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT25FS040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT25FS040 } } },
+ },
.block_erasers =
{
{
@@ -2037,13 +2098,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26DF041",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF041,
.total_size = 512,
.page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26DF041 } } },
+ },
.block_erasers =
{
{
@@ -2068,13 +2130,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26DF081A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF081A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26DF081A } } },
+ },
.block_erasers =
{
{
@@ -2105,13 +2168,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26DF161",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF161,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26DF161 } } },
+ },
.block_erasers =
{
{
@@ -2142,13 +2206,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26DF161A",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF161A,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26DF161A } } },
+ },
.block_erasers =
{
{
@@ -2180,13 +2245,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26DF321",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26DF321,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26DF321 } } },
+ },
.printlock = spi_prettyprint_status_register_at26df081a,
.unlock = spi_disable_blockprotect,
.write = spi_chip_write_256,
@@ -2197,13 +2263,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT26F004",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT26F004,
.total_size = 512,
.page_size = 256,
.tested = {.probe = NT, .read = NT, .erase = NT, .write = BAD },
.feature_bits = FEATURE_WRSR_WREN,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT26F004 } } },
+ },
.block_erasers =
{
{
@@ -2233,13 +2300,13 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT29C512",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C512,
.total_size = 64,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 10 ms, Enter=Exec */
+ .probers =
+ {
+ { probe_jedec_longreset, { 2, { ATMEL_ID, ATMEL_AT29C512 } } }, /* 10 ms, Enter=Exec */
+ },
.block_erasers =
{
{
@@ -2256,13 +2323,13 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT29C010A",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C010A,
.total_size = 128,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec, /* 10 ms, Enter=Exec */
+ .probers =
+ {
+ { probe_jedec_longreset, { 2, { ATMEL_ID, ATMEL_AT29C010A } } }, /* 10 ms, Enter=Exec */
+ },
.block_erasers =
{
{
@@ -2279,13 +2346,13 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT29C020",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C020,
.total_size = 256,
.page_size = 256,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 10 ms */
+ .probers =
+ {
+ { probe_jedec_longreset, { 2, { ATMEL_ID, ATMEL_AT29C020 } } }, /* 10 ms */
+ },
.block_erasers =
{
{
@@ -2302,13 +2369,13 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT29C040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT29C040A,
.total_size = 512,
.page_size = 256,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec, /* 10 ms */
+ .probers =
+ {
+ { probe_jedec_longreset, { 2, { ATMEL_ID, ATMEL_AT29C040A } } }, /* 10 ms */
+ },
.block_erasers =
{
{
@@ -2325,15 +2392,16 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT45CS1282",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45CS1282,
.total_size = 16896 /* No power of two sizes */,
.page_size = 1056 /* No power of two sizes */,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77 (4 dummy bytes); write 0x9A (via buffer) */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45CS1282 } } },
+ },
.block_erasers =
{
{
@@ -2354,24 +2422,26 @@ const struct flashchip flashchips[] = {
{
.vendor = "Atmel",
- .name = "AT45DB011D",
+ .name = "AT45DB011D (power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB011D,
- .total_size = 128 /* or 132, determined from status register */,
- .page_size = 256 /* or 264, determined from status register */,
+ .total_size = 128,
+ .page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB011D } } },
+ },
.block_erasers =
{
{
.eraseblocks = { {256, 512} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 256, 512/8} },
+ .eraseblocks = { {8 * 256, 64} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
@@ -2387,7 +2457,7 @@ const struct flashchip flashchips[] = {
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_256bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
.voltage = {2700, 3600},
@@ -2395,40 +2465,42 @@ const struct flashchip flashchips[] = {
{
.vendor = "Atmel",
- .name = "AT45DB021D",
+ .name = "AT45DB011D (non-power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB021D,
- .total_size = 256 /* or 264, determined from status register */,
- .page_size = 256 /* or 264, determined from status register */,
+ .total_size = (128 / 32) * 33,
+ .page_size = (256 / 32) * 33,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB011D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {256, 1024} },
+ .eraseblocks = { {(256 / 32) * 33, 512} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 256, 1024/8} },
+ .eraseblocks = { {(2048 / 32) * 33, 64} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 256, 1},
- {120 * 256, 1},
- {128 * 256, 7},
+ {8 * (256 / 32) * 33, 1},
+ {120 * (256 / 32) * 33, 1},
+ {128 * (256 / 32) * 33, 3},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {256 * 1024, 1} },
+ .eraseblocks = { {(128 / 32) * 33 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_264bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
.voltage = {2700, 3600},
@@ -2436,205 +2508,213 @@ const struct flashchip flashchips[] = {
{
.vendor = "Atmel",
- .name = "AT45DB041D",
+ .name = "AT45DB021D (power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB041D,
- .total_size = 512 /* or 528, determined from status register */,
- .page_size = 256 /* or 264, determined from status register */,
+ .total_size = 256,
+ .page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
- .tested = TEST_OK_PREW,
- .probe = probe_spi_at45db,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB021D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {256, 2048} },
+ .eraseblocks = { {256, 1024} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 256, 2048/8} },
+ .eraseblocks = { {8 * 256, 1024/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
{8 * 256, 1},
- {248 * 256, 1},
- {256 * 256, 7},
+ {120 * 256, 1},
+ {128 * 256, 7},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {512 * 1024, 1} },
+ .eraseblocks = { {256 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_256bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
- .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ .voltage = {2700, 3600},
},
{
.vendor = "Atmel",
- .name = "AT45DB081D",
+ .name = "AT45DB021D (non-power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB081D,
- .total_size = 1024 /* or 1056, determined from status register */,
- .page_size = 256 /* or 264, determined from status register */,
+ .total_size = (256 / 32) * 33,
+ .page_size = (256 / 32) * 33,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB021D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {256, 4096} },
+ .eraseblocks = { {(256 / 32) * 33, 1024} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 256, 4096/8} },
+ .eraseblocks = { {8 * (256 / 32) * 33, 1024/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 256, 1},
- {248 * 256, 1},
- {256 * 256, 15},
+ {8 * (256 / 32) * 33, 1},
+ {120 * (256 / 32) * 33, 1},
+ {128 * (256 / 32) * 33, 7},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {1024 * 1024, 1} },
+ .eraseblocks = { {(256 / 32) * 33 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_264bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
- .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ .voltage = {2700, 3600},
},
{
.vendor = "Atmel",
- .name = "AT45DB161D",
+ .name = "AT45DB041D (power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB161D,
- .total_size = 2048 /* or 2112, determined from status register */,
- .page_size = 512 /* or 528, determined from status register */,
+ .total_size = 512,
+ .page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB041D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {512, 4096} },
+ .eraseblocks = { {256, 2048} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 512, 4096/8} },
+ .eraseblocks = { {8 * 256, 2048/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 512, 1},
- {248 * 512, 1},
- {256 * 512, 15},
+ {8 * 256, 1},
+ {248 * 256, 1},
+ {256 * 256, 7},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {2048 * 1024, 1} },
+ .eraseblocks = { {512 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_256bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
.voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
},
-
{
.vendor = "Atmel",
- .name = "AT45DB321C",
+ .name = "AT45DB041D (non-power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321C,
- .total_size = 4224 /* No power of two sizes */,
- .page_size = 528 /* No power of two sizes */,
+ .total_size = (512 / 32) * 33,
+ .page_size = (256 / 32) * 33,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
- /* OTP: 128B total, 64B pre-programmed; read 0x77 (4 dummy bytes); write 0x9A (via buffer) */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
- .tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .tested = TEST_OK_PREW,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB041D, 0x00 } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {528, 8192} },
+ .eraseblocks = { {(256 / 32) * 33, 2048} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 528, 8192/8} },
+ .eraseblocks = { {8 * (256 / 32) * 33, 2048/8} },
.block_erase = spi_erase_at45db_block,
- }, /* Although the datasheets describes sectors (which can be write protected)
- * there seems to be no erase functions for them.
- {
+ }, {
.eraseblocks = {
- {8 * 528, 1},
- {120 * 528, 1},
- {128 * 528, 63},
+ {8 * (256 / 32) * 33, 1},
+ {248 * (256 / 32) * 33, 1},
+ {256 * (256 / 32) * 33, 7},
},
.block_erase = spi_erase_at45db_sector
- }, */ {
- .eraseblocks = { {4224 * 1024, 1} },
+ }, {
+ .eraseblocks = { {(512 / 32) * 33 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
- .printlock = spi_prettyprint_status_register_at45db, /* Bit 0 is undefined, no lockdown */
- .gran = write_gran_528bytes,
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_264bytes,
.write = spi_write_at45db,
- .read = spi_read_at45db_e8, /* 3 address and 4 dummy bytes */
- .voltage = {2700, 3600},
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
},
{
.vendor = "Atmel",
- .name = "AT45DB321D",
+ .name = "AT45DB081D (power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321D,
- .total_size = 4096 /* or 4224, determined from status register */,
- .page_size = 512 /* or 528, determined from status register */,
+ .total_size = 1024,
+ .page_size = 256,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB081D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {512, 8192} },
+ .eraseblocks = { {256, 4096} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 512, 8192/8} },
+ .eraseblocks = { {8 * 256, 4096/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 512, 1},
- {120 * 512, 1},
- {128 * 512, 63},
+ {8 * 256, 1},
+ {248 * 256, 1},
+ {256 * 256, 15},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {4096 * 1024, 1} },
+ .eraseblocks = { {1024 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_256bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
.voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
@@ -2642,81 +2722,428 @@ const struct flashchip flashchips[] = {
{
.vendor = "Atmel",
- .name = "AT45DB321E",
+ .name = "AT45DB081D (non-power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB321C,
- .total_size = 4096 /* or 4224, determined from status register */,
- .page_size = 512 /* or 528, determined from status register */,
+ .total_size = (1024 / 32) * 33,
+ .page_size = (256 / 32) * 33,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB081D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {512, 8192} },
+ .eraseblocks = { {(256 / 32) * 33, 4096} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 512, 8192/8} },
+ .eraseblocks = { {8 * (256 / 32) * 33, 4096/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 512, 1},
- {120 * 512, 1},
- {128 * 512, 63},
+ {8 * (256 / 32) * 33, 1},
+ {248 * (256 / 32) * 33, 1},
+ {256 * (256 / 32) * 33, 15},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {4096 * 1024, 1} },
+ .eraseblocks = { {(1024 / 32) * 33 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_264bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB161D (power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = 2048,
+ .page_size = 512,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_OK_PREW,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB161D } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {512, 4096} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * 512, 4096/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * 512, 1},
+ {248 * 512, 1},
+ {256 * 512, 15},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {2048 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_512bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB161D (non-power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = (2048 / 32) * 33,
+ .page_size = (512 / 32) * 33,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_OK_PREW,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB161D } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {(512 / 32) * 33, 4096} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * (512 / 32) * 33, 4096/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * (512 / 32) * 33, 1},
+ {248 * (512 / 32) * 33, 1},
+ {256 * (512 / 32) * 33, 15},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {(2048 / 32) * 33 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_528bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB321C",
+ .bustype = BUS_SPI,
+ .total_size = 4224 /* No power of two sizes */,
+ .page_size = 528 /* No power of two sizes */,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77 (4 dummy bytes); write 0x9A (via buffer) */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB321C } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {528, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * 528, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, /* Although the datasheets describes sectors (which can be write protected)
+ * there seems to be no erase functions for them.
+ {
+ .eraseblocks = {
+ {8 * 528, 1},
+ {120 * 528, 1},
+ {128 * 528, 63},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, */ {
+ .eraseblocks = { {4224 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .printlock = spi_prettyprint_status_register_at45db, /* Bit 0 is undefined, no lockdown */
+ .gran = write_gran_528bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db_e8, /* 3 address and 4 dummy bytes */
+ .voltage = {2700, 3600},
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB321D (power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = 4096,
+ .page_size = 512,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB321D } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {512, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * 512, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * 512, 1},
+ {120 * 512, 1},
+ {128 * 512, 63},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {4096 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_512bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB321D (non-power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = (4096 / 32) * 33,
+ .page_size = (512 / 32) * 33,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB321D } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {(512 / 32) * 33, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * (512 / 32) * 33, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * (512 / 32) * 33, 1},
+ {120 * (512 / 32) * 33, 1},
+ {128 * (512 / 32) * 33, 63},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {(4096 / 32) * 33 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_512bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2700, 3600}, /* 2.5-3.6V & 2.7-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB321E (power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = 4096,
+ .page_size = 512,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB321C } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {512, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * 512, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * 512, 1},
+ {120 * 512, 1},
+ {128 * 512, 63},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {4096 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db, /* has a 2nd status register */
- /* granularity will be set by the probing function. */
+ .gran = write_gran_512bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2500, 3600}, /* 2.3-3.6V & 2.5-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB321E (non-power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = (4096 / 32) * 33,
+ .page_size = (512 / 32) * 33,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB321C } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {(512 / 32) * 33, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * (512 / 32) * 33, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * (512 / 32) * 33, 1},
+ {120 * (512 / 32) * 33, 1},
+ {128 * (512 / 32) * 33, 63},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {(4096 / 32) * 33 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db, /* has a 2nd status register */
+ .gran = write_gran_528bytes,
+ .write = spi_write_at45db,
+ .read = spi_read_at45db, /* Fast read (0x0B) supported */
+ .voltage = {2500, 3600}, /* 2.3-3.6V & 2.5-3.6V models available */
+ },
+
+ {
+ .vendor = "Atmel",
+ .name = "AT45DB642D (power-of-two)",
+ .bustype = BUS_SPI,
+ .total_size = 8192,
+ .page_size = 1024,
+ /* does not support EWSR nor WREN and has no writable status register bits whatsoever */
+ /* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
+ .feature_bits = FEATURE_OTP,
+ .tested = TEST_UNTESTED,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x01 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB642D } } },
+ },
+ .block_erasers =
+ {
+ {
+ .eraseblocks = { {1024, 8192} },
+ .block_erase = spi_erase_at45db_page,
+ }, {
+ .eraseblocks = { {8 * 1024, 8192/8} },
+ .block_erase = spi_erase_at45db_block,
+ }, {
+ .eraseblocks = {
+ {8 * 1024, 1},
+ {248 * 1024, 1},
+ {256 * 1024, 31},
+ },
+ .block_erase = spi_erase_at45db_sector
+ }, {
+ .eraseblocks = { {8192 * 1024, 1} },
+ .block_erase = spi_erase_at45db_chip,
+ }
+ },
+ .unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
+ .printlock = spi_prettyprint_status_register_at45db,
+ .gran = write_gran_1024bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
- .voltage = {2500, 3600}, /* 2.3-3.6V & 2.5-3.6V models available */
+ .voltage = {2700, 3600},
},
-
{
.vendor = "Atmel",
- .name = "AT45DB642D",
+ .name = "AT45DB642D (non-power-of-two)",
.bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT45DB642D,
- .total_size = 8192 /* or 8448, determined from status register */,
- .page_size = 1024 /* or 1056, determined from status register */,
+ .total_size = (8192 / 32) * 33,
+ .page_size = (1024 / 32) * 33,
/* does not support EWSR nor WREN and has no writable status register bits whatsoever */
/* OTP: 128B total, 64B pre-programmed; read 0x77; write 0x9B */
.feature_bits = FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_at45db,
+ .probers =
+ {
+ { probe_spi_at45db, { 1, { 0x00 } } },
+ { probe_spi_rdid, { 3, { ATMEL_ID, ATMEL_AT45DB642D } } },
+ },
.block_erasers =
{
{
- .eraseblocks = { {1024, 8192} },
+ .eraseblocks = { {(1024 / 32) * 33, 8192} },
.block_erase = spi_erase_at45db_page,
}, {
- .eraseblocks = { {8 * 1024, 8192/8} },
+ .eraseblocks = { {8 * (1024 / 32) * 33, 8192/8} },
.block_erase = spi_erase_at45db_block,
}, {
.eraseblocks = {
- {8 * 1024, 1},
- {248 * 1024, 1},
- {256 * 1024, 31},
+ {8 * (1024 / 32) * 33, 1},
+ {248 * (1024 / 32) * 33, 1},
+ {256 * (1024 / 32) * 33, 31},
},
.block_erase = spi_erase_at45db_sector
}, {
- .eraseblocks = { {8192 * 1024, 1} },
+ .eraseblocks = { {(8192 / 32) * 33 * 1024, 1} },
.block_erase = spi_erase_at45db_chip,
}
},
.unlock = spi_disable_blockprotect_at45db, /* Impossible if locked down or #WP is low */
.printlock = spi_prettyprint_status_register_at45db,
- /* granularity will be set by the probing function. */
+ .gran = write_gran_1056bytes,
.write = spi_write_at45db,
.read = spi_read_at45db, /* Fast read (0x0B) supported */
.voltage = {2700, 3600},
@@ -2726,13 +3153,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49BV512",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49BV512,
.total_size = 64,
.page_size = 64,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49BV512 } } },
+ },
.block_erasers =
{
{
@@ -2749,13 +3177,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F002(N)",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F002N,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F002N } } },
+ },
.block_erasers =
{
{
@@ -2780,13 +3209,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F002(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F002NT,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F002NT } } },
+ },
.block_erasers =
{
{
@@ -2811,13 +3241,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49(H)F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F010,
.total_size = 128,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F010 } } },
+ },
.block_erasers =
{
{
@@ -2835,13 +3266,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F020",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F020,
.total_size = 256,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F020 } } },
+ },
.block_erasers =
{
{
@@ -2865,13 +3297,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F040,
.total_size = 512,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F040 } } },
+ },
.block_erasers =
{
{
@@ -2895,13 +3328,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F080",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F080,
.total_size = 1024,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F080 } } },
+ },
.block_erasers =
{
{
@@ -2926,13 +3360,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49F080T",
.bustype = BUS_PARALLEL,
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49F080T,
.total_size = 1024,
.page_size = 0, /* unused */
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ATMEL_ID, ATMEL_AT49F080T } } },
+ },
.block_erasers =
{
{
@@ -2956,13 +3391,14 @@ const struct flashchip flashchips[] = {
.vendor = "Atmel",
.name = "AT49LH002",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = ATMEL_ID,
- .model_id = ATMEL_AT49LH002,
.total_size = 256,
.page_size = 0, /* unused */
.feature_bits = FEATURE_REGISTERMAP, /* TODO: LPC OK too? */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted, /* TODO: 0xff cmd not documented? */
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ATMEL_ID, ATMEL_AT49LH002 } } }, /* TODO: 0xff cmd not documented? */
+ },
.block_erasers =
{
{
@@ -2991,13 +3427,14 @@ const struct flashchip flashchips[] = {
.vendor = "Catalyst",
.name = "CAT28F512",
.bustype = BUS_PARALLEL,
- .manufacture_id = CATALYST_ID,
- .model_id = CATALYST_CAT28F512,
.total_size = 64,
.page_size = 0, /* unused */
.feature_bits = 0,
.tested = TEST_OK_PR,
- .probe = probe_jedec, /* FIXME! */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { CATALYST_ID, CATALYST_CAT28F512 } } }, /* FIXME! */
+ },
.block_erasers =
{
{
@@ -3014,13 +3451,14 @@ const struct flashchip flashchips[] = {
.vendor = "Bright",
.name = "BM29F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = BRIGHT_ID,
- .model_id = BRIGHT_BM29F040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { BRIGHT_ID, BRIGHT_BM29F040 } } },
+ },
.block_erasers =
{
{
@@ -3040,13 +3478,14 @@ const struct flashchip flashchips[] = {
.vendor = "ESMT",
.name = "F49B002UA",
.bustype = BUS_PARALLEL,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F49B002UA,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { ESMT_ID, ESMT_F49B002UA } } },
+ },
.block_erasers =
{
{
@@ -3071,13 +3510,14 @@ const struct flashchip flashchips[] = {
.vendor = "ESMT",
.name = "F25L008A",
.bustype = BUS_SPI,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F25L008A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ESMT_ID, ESMT_F25L008A } } },
+ },
.block_erasers =
{
{
@@ -3105,13 +3545,14 @@ const struct flashchip flashchips[] = {
.vendor = "ESMT",
.name = "F25L32PA",
.bustype = BUS_SPI,
- .manufacture_id = ESMT_ID,
- .model_id = ESMT_F25L32PA,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ESMT_ID, ESMT_F25L32PA } } },
+ },
.block_erasers =
{
{
@@ -3139,13 +3580,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B05",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B05 } } },
+ },
.block_erasers =
{
{
@@ -3172,13 +3614,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B05T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B05 } } },
+ },
.block_erasers =
{
{
@@ -3205,13 +3648,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B10 } } },
+ },
.block_erasers =
{
{
@@ -3238,13 +3682,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B10T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B10 } } },
+ },
.block_erasers =
{
{
@@ -3271,13 +3716,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B20 } } },
+ },
.block_erasers =
{
{
@@ -3305,13 +3751,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B20T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B20 } } },
+ },
.block_erasers =
{
{
@@ -3339,13 +3786,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B40 } } },
+ },
.block_erasers =
{
{
@@ -3373,13 +3821,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B40T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B40 } } },
+ },
.block_erasers =
{
{
@@ -3407,13 +3856,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B80 } } },
+ },
.block_erasers =
{
{
@@ -3441,13 +3891,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B80T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B80 } } },
+ },
.block_erasers =
{
{
@@ -3475,13 +3926,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B16 } } },
+ },
.block_erasers =
{
{
@@ -3509,13 +3961,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B16T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B16 } } },
+ },
.block_erasers =
{
{
@@ -3543,13 +3996,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B32 } } },
+ },
.block_erasers =
{
{
@@ -3577,13 +4031,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B32T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B32 } } },
+ },
.block_erasers =
{
{
@@ -3611,13 +4066,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B64 } } },
+ },
.block_erasers =
{
{
@@ -3645,13 +4101,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25B64T",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25B64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25B64 } } },
+ },
.block_erasers =
{
{
@@ -3679,13 +4136,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F05",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F05,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F05 } } },
+ },
.block_erasers =
{
{
@@ -3716,13 +4174,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F10 } } },
+ },
.block_erasers =
{
{
@@ -3753,13 +4212,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F20 } } },
+ },
.block_erasers =
{
{
@@ -3790,13 +4250,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F40 } } },
+ },
.block_erasers =
{
{
@@ -3824,13 +4285,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F80 } } },
+ },
.block_erasers =
{
{
@@ -3858,13 +4320,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F16 } } },
+ },
.block_erasers =
{
{
@@ -3892,13 +4355,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F32 } } },
+ },
.block_erasers =
{
{
@@ -3926,13 +4390,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25F64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25F64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25F64 } } },
+ },
.block_erasers =
{
{
@@ -3960,14 +4425,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q40,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q40 } } },
+ },
.block_erasers =
{
{
@@ -3995,14 +4461,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q80(A)",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q80 } } },
+ },
.block_erasers =
{
{
@@ -4032,14 +4499,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q16,
.total_size = 2048,
.page_size = 256,
/* OTP: D16 512B/Q16 128B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q16 } } },
+ },
.block_erasers =
{
{
@@ -4071,14 +4539,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q32(A/B)",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q32,
.total_size = 4096,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q32 } } },
+ },
.block_erasers =
{
{
@@ -4106,14 +4575,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q64,
.total_size = 8192,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q64 } } },
+ },
.block_erasers =
{
{
@@ -4141,14 +4611,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25Q128",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25Q128,
.total_size = 16384,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25Q128 } } },
+ },
.block_erasers =
{
{
@@ -4175,8 +4646,6 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25QH16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH16,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
@@ -4184,7 +4653,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25QH16 } } },
+ },
.block_erasers =
{
{
@@ -4212,8 +4684,6 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25QH32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH32,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
@@ -4221,7 +4691,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25QH32 } } },
+ },
.block_erasers =
{
{
@@ -4249,8 +4722,6 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25QH64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH64,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
@@ -4258,7 +4729,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25QH64 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 2048} },
@@ -4285,8 +4759,6 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25QH128",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25QH128,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
@@ -4294,7 +4766,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25QH128 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 4096} },
@@ -4321,14 +4796,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S10",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S10,
.total_size = 128,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S10 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 32} },
@@ -4355,14 +4831,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S20",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S20,
.total_size = 256,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S20 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 64} },
@@ -4389,14 +4866,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S40",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S40,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S40 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 128} },
@@ -4423,14 +4901,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S80",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S80 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 256} },
@@ -4457,14 +4936,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S16",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S16,
.total_size = 2048,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S16 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 512} },
@@ -4494,14 +4974,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S32",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S32,
.total_size = 4096,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S32 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 1024} },
@@ -4531,14 +5012,15 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN25S64",
.bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = EON_EN25S64,
.total_size = 8192,
.page_size = 256,
/* OTP: 512B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { EON_ID_NOPREFIX, EON_EN25S64 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 2048} },
@@ -4565,13 +5047,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN29F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F010,
.total_size = 128,
.page_size = 128,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { EON_ID, EON_EN29F010 } } },
+ },
.block_erasers =
{
{
@@ -4592,13 +5075,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN29F002(A)(N)B",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F002B,
.total_size = 256,
.page_size = 256,
- .feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
+ .feature_bits = FEATURE_ADDR_AAA,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_aaa, { 4, { EON_ID, EON_EN29F002B } } },
+ },
.block_erasers =
{
{
@@ -4623,13 +5107,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN29F002(A)(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29F002T,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_aaa, { 2, { EON_ID, EON_EN29F002T } } },
+ },
.block_erasers =
{
{
@@ -4654,13 +5139,14 @@ const struct flashchip flashchips[] = {
.vendor = "Eon",
.name = "EN29LV640B",
.bustype = BUS_PARALLEL,
- .manufacture_id = EON_ID,
- .model_id = EON_EN29LV640B,
.total_size = 8192,
.page_size = 8192,
.feature_bits = 0,
.tested = TEST_OK_PREW,
- .probe = probe_en29lv640b,
+ .probers =
+ {
+ { probe_en29lv640b, { 3, { EON_ID, EON_EN29LV640B } } },
+ },
.block_erasers =
{
{
@@ -4683,13 +5169,14 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29F004BC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F004BC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { FUJITSU_ID, FUJITSU_MBM29F004BC } } },
+ },
.block_erasers =
{
{
@@ -4714,13 +5201,14 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29F004TC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F004TC,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { FUJITSU_ID, FUJITSU_MBM29F004TC } } },
+ },
.block_erasers =
{
{
@@ -4746,12 +5234,13 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29F400BC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F400BC,
.total_size = 512,
.page_size = 64 * 1024,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 3, { FUJITSU_ID, FUJITSU_MBM29F400BC } } },
+ },
.block_erasers =
{
{
@@ -4776,12 +5265,13 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29F400TC",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29F400TC,
.total_size = 512,
.page_size = 64 * 1024,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 3, { FUJITSU_ID, FUJITSU_MBM29F400TC } } },
+ },
.block_erasers =
{
{
@@ -4806,12 +5296,13 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29LV160BE",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29LV160BE,
- .total_size = 2 * 1024,
+ .total_size = 2048,
.page_size = 0,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 3, { FUJITSU_ID, FUJITSU_MBM29LV160BE } } },
+ },
.block_erasers =
{
{
@@ -4836,12 +5327,13 @@ const struct flashchip flashchips[] = {
.vendor = "Fujitsu",
.name = "MBM29LV160TE",
.bustype = BUS_PARALLEL,
- .manufacture_id = FUJITSU_ID,
- .model_id = FUJITSU_MBM29LV160TE,
- .total_size = 2 * 1024,
+ .total_size = 2048,
.page_size = 0,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 3, { FUJITSU_ID, FUJITSU_MBM29LV160TE } } },
+ },
.block_erasers =
{
{
@@ -4866,14 +5358,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25LQ32",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25LQ32,
.total_size = 4096,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25LQ32 } } },
+ },
.block_erasers =
{
{
@@ -4904,13 +5397,14 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q512",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q512 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 16} },
@@ -4937,13 +5431,14 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q10",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q10 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 32} },
@@ -4973,13 +5468,14 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q20(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q20 } } },
+ },
.block_erasers =
{
{
@@ -5010,13 +5506,14 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q40(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q40 } } },
+ },
.block_erasers =
{
{
@@ -5047,14 +5544,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q80(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q80,
.total_size = 1024,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q80 } } },
+ },
.block_erasers =
{
{
@@ -5085,14 +5583,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q16(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q16,
.total_size = 2048,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q16 } } },
+ },
.block_erasers =
{
{
@@ -5123,14 +5622,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q32(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q32,
.total_size = 4096,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q32 } } },
+ },
.block_erasers =
{
{
@@ -5161,14 +5661,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q64(B)",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q64,
.total_size = 8192,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q64 } } },
+ },
.block_erasers =
{
{
@@ -5199,14 +5700,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25Q128B",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25Q128,
.total_size = 16384,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25Q128 } } },
+ },
.block_erasers =
{
{
@@ -5237,14 +5739,15 @@ const struct flashchip flashchips[] = {
.vendor = "GigaDevice",
.name = "GD25T80",
.bustype = BUS_SPI,
- .manufacture_id = GIGADEVICE_ID,
- .model_id = GIGADEVICE_GD25T80,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; enter 0x3A */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { GIGADEVICE_ID, GIGADEVICE_GD25T80 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 256} },
@@ -5274,13 +5777,14 @@ const struct flashchip flashchips[] = {
.vendor = "Hyundai",
.name = "HY29F002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F002T,
.total_size = 256,
.page_size = 256 * 1024,
.feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { HYUNDAI_ID, HYUNDAI_HY29F002T } } },
+ },
.block_erasers =
{
{
@@ -5305,13 +5809,14 @@ const struct flashchip flashchips[] = {
.vendor = "Hyundai",
.name = "HY29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F002B,
.total_size = 256,
.page_size = 256 * 1024,
.feature_bits = FEATURE_EITHER_RESET, /* Some revisions may need FEATURE_ADDR_2AA */
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { HYUNDAI_ID, HYUNDAI_HY29F002B } } },
+ },
.block_erasers =
{
{
@@ -5336,13 +5841,14 @@ const struct flashchip flashchips[] = {
.vendor = "Hyundai",
.name = "HY29F040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = HYUNDAI_ID,
- .model_id = HYUNDAI_HY29F040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { HYUNDAI_ID, HYUNDAI_HY29F040A } } },
+ },
.block_erasers =
{
{
@@ -5362,14 +5868,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F160S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F160S33B8,
.total_size = 2048,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F160S33B8 } } },
+ },
.block_erasers =
{
{
@@ -5378,7 +5885,7 @@ const struct flashchip flashchips[] = {
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
{8 * 1024, 8},
- {64 * 1024, 31} // inaccessible
+ {64 * 1024, 31} inaccessible
},
.block_erase = spi_block_erase_40,
}, { */
@@ -5400,14 +5907,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F160S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F160S33T8,
.total_size = 2048,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F160S33T8 } } },
+ },
.block_erasers =
{
{
@@ -5415,7 +5923,7 @@ const struct flashchip flashchips[] = {
* opcode 0x40. Trying to access an address outside these 8 8kB blocks does
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
- {64 * 1024, 31}, // inaccessible
+ {64 * 1024, 31}, inaccessible
{8 * 1024, 8}
},
.block_erase = spi_block_erase_40,
@@ -5438,14 +5946,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F320S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F320S33B8,
.total_size = 4096,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F320S33B8 } } },
+ },
.block_erasers =
{
{
@@ -5454,7 +5963,7 @@ const struct flashchip flashchips[] = {
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
{8 * 1024, 8},
- {64 * 1024, 63} // inaccessible
+ {64 * 1024, 63} inaccessible
},
.block_erase = spi_block_erase_40,
}, { */
@@ -5476,14 +5985,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F320S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F320S33T8,
.total_size = 4096,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F320S33T8 } } },
+ },
.block_erasers =
{
{
@@ -5491,7 +6001,7 @@ const struct flashchip flashchips[] = {
* opcode 0x40. Trying to access an address outside these 8 8kB blocks does
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
- {64 * 1024, 63}, // inaccessible
+ {64 * 1024, 63}, inaccessible
{8 * 1024, 8}
},
.block_erase = spi_block_erase_40,
@@ -5514,14 +6024,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F640S33B8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F640S33B8,
.total_size = 8192,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F640S33B8 } } },
+ },
.block_erasers =
{
{
@@ -5530,7 +6041,7 @@ const struct flashchip flashchips[] = {
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
{8 * 1024, 8},
- {64 * 1024, 127} // inaccessible
+ {64 * 1024, 127} inaccessible
},
.block_erase = spi_block_erase_40,
}, { */
@@ -5552,14 +6063,15 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "25F640S33T8",
.bustype = BUS_SPI,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_25F640S33T8,
.total_size = 8192,
.page_size = 256,
/* OTP: 506B total (2x 8B, 30x 16B, 1x 10B); read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { INTEL_ID, INTEL_25F640S33T8 } } },
+ },
.block_erasers =
{
{
@@ -5567,7 +6079,7 @@ const struct flashchip flashchips[] = {
* opcode 0x40. Trying to access an address outside these 8 8kB blocks does
* have no effect on the memory contents, but sets a flag in the SR.
.eraseblocks = {
- {64 * 1024, 127}, // inaccessible
+ {64 * 1024, 127}, inaccessible
{8 * 1024, 8}
},
.block_erase = spi_block_erase_40,
@@ -5590,12 +6102,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F001BN/BX-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F001B,
.total_size = 128,
.page_size = 128 * 1024, /* 8k + 2x4k + 112k */
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { INTEL_ID, INTEL_28F001B } } },
+ },
.block_erasers =
{
{
@@ -5616,12 +6129,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F001BN/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F001T,
.total_size = 128,
.page_size = 128 * 1024, /* 112k + 2x4k + 8k */
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { INTEL_ID, INTEL_28F001T } } },
+ },
.block_erasers =
{
{
@@ -5642,12 +6156,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F002BC/BL/BV/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F002T,
.total_size = 256,
.page_size = 256 * 1024,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_28F002T } } },
+ },
.block_erasers =
{
{
@@ -5668,12 +6183,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F008S3/S5/SC",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004S3,
.total_size = 512,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_28F004S3 } } },
+ },
.block_erasers =
{
{
@@ -5690,12 +6206,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F004B5/BE/BV/BX-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004B,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_28F004B } } },
+ },
.block_erasers =
{
{
@@ -5716,12 +6233,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F004B5/BE/BV/BX-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F004T,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_28F004T } } },
+ },
.block_erasers =
{
{
@@ -5742,12 +6260,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F400BV/BX/CE/CV-B",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F400B,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_shifted,
+ .probers =
+ {
+ { probe_82802ab_shifted, { 3, { INTEL_ID, INTEL_28F400B } } },
+ },
.block_erasers =
{
{
@@ -5768,12 +6287,13 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "28F400BV/BX/CE/CV-T",
.bustype = BUS_PARALLEL,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_28F400T,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_shifted,
+ .probers =
+ {
+ { probe_82802ab_shifted, { 3, { INTEL_ID, INTEL_28F400T } } },
+ },
.block_erasers =
{
{
@@ -5794,13 +6314,14 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "82802AB",
.bustype = BUS_FWH,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_82802AB,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_82802AB } } },
+ },
.block_erasers =
{
{
@@ -5818,13 +6339,14 @@ const struct flashchip flashchips[] = {
.vendor = "Intel",
.name = "82802AC",
.bustype = BUS_FWH,
- .manufacture_id = INTEL_ID,
- .model_id = INTEL_82802AC,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { INTEL_ID, INTEL_82802AC } } },
+ },
.block_erasers =
{
{
@@ -5842,12 +6364,13 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX23L3254",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX23L3254,
.total_size = 4096,
.page_size = 256,
.tested = {.probe = OK, .read = OK, .erase = NA, .write = NA},
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX23L3254 } } },
+ },
.write = NULL, /* MX23L3254 is a mask ROM, so it is read-only */
.read = spi_chip_read, /* Fast read (0x0B) supported */
.voltage = {3000, 3600},
@@ -5857,14 +6380,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L512(E)/MX25V512(C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L512,
.total_size = 64,
.page_size = 256,
/* MX25L512E supports SFDP */
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L512 } } },
+ },
.block_erasers =
{
{
@@ -5895,14 +6419,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1005(C)/MX25L1006E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1005,
.total_size = 128,
.page_size = 256,
/* MX25L1006E supports SFDP */
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1005 } } },
+ },
.block_erasers =
{
{
@@ -5930,13 +6455,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L2005(C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L2005,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L2005 } } },
+ },
.block_erasers =
{
{
@@ -5967,13 +6493,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L4005(A/C)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L4005,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L4005 } } },
+ },
.block_erasers =
{
{
@@ -6004,13 +6531,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L8005/MX25V8005",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L8005,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L8005 } } },
+ },
.block_erasers =
{
{
@@ -6041,13 +6569,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1605",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1605 } } },
+ },
.block_erasers =
{
{
@@ -6075,14 +6604,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1605A/MX25L1606E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 (MX25L1606E only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1605 } } },
+ },
.block_erasers =
{
{
@@ -6113,13 +6643,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1605D/MX25L1608D/MX25L1673E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1605,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1605 } } },
+ },
.block_erasers =
{
{
@@ -6147,14 +6678,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1635D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1635D,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1635D } } },
+ },
.block_erasers =
{
{
@@ -6182,14 +6714,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L1635E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L1635E,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L1635E } } },
+ },
.block_erasers =
{
{
@@ -6217,13 +6750,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L3205(A)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L3205 } } },
+ },
.block_erasers =
{
{
@@ -6251,14 +6785,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L3205D/MX25L3208D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L3205 } } },
+ },
.block_erasers =
{
{
@@ -6286,14 +6821,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L3206E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L3205 } } },
+ },
.block_erasers =
{
{
@@ -6324,14 +6860,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L3273E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3205,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L3205 } } },
+ },
.block_erasers =
{
{
@@ -6362,14 +6899,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L3235D",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L3235D,
.total_size = 4096,
.page_size = 256,
/* OTP: 256B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L3235D } } },
+ },
.block_erasers =
{
{
@@ -6397,14 +6935,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L6405(D)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* MX25L6405D has 64B of OTP; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L6405 } } },
+ },
.block_erasers =
{
{
@@ -6432,14 +6971,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L6406E/MX25L6436E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* OTP: 06E 64B/36E 512B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L6405 } } },
+ },
.block_erasers =
{
{
@@ -6467,15 +7007,16 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L6445E/MX25L6473E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L6405,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 512B total; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L6405 } } },
+ },
.block_erasers =
{
{
@@ -6506,14 +7047,15 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25L12805(D)",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25L12805,
.total_size = 16384,
.page_size = 256,
/* MX25L12805D has 64B of OTP; enter 0xB1, exit 0xC1 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25L12805 } } },
+ },
.block_erasers =
{
{
@@ -6541,15 +7083,16 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25U1635E",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U1635E,
.total_size = 2048,
.page_size = 256,
/* OTP: 512B total; enter 0xB1, exit 0xC1 */
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25U1635E } } },
+ },
.block_erasers =
{
{
@@ -6581,8 +7124,6 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25U3235E/F",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U3235E,
.total_size = 4096,
.page_size = 256,
/* F model supports SFDP */
@@ -6590,7 +7131,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25U3235E } } },
+ },
.block_erasers =
{
{
@@ -6622,8 +7166,6 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX25U6435E/F",
.bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX25U6435E,
.total_size = 8192,
.page_size = 256,
/* F model supports SFDP */
@@ -6631,7 +7173,10 @@ const struct flashchip flashchips[] = {
/* QPI enable 0x35, disable 0xF5 (0xFF et al. work too) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { MACRONIX_ID, MACRONIX_MX25U6435E } } },
+ },
.block_erasers =
{
{
@@ -6663,13 +7208,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29F001B",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F001B,
.total_size = 128,
.page_size = 32 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29F001B } } },
+ },
.block_erasers =
{
{
@@ -6695,13 +7241,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29F001T",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F001T,
.total_size = 128,
.page_size = 32 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29F001T } } },
+ },
.block_erasers =
{
{
@@ -6727,13 +7274,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29F002(N)B",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F002B,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29F002B } } },
+ },
.block_erasers =
{
{
@@ -6758,13 +7306,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29F002(N)T",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29F002T } } },
+ },
.block_erasers =
{
{
@@ -6789,13 +7338,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29F040",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29F040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29F040 } } },
+ },
.block_erasers =
{
{
@@ -6815,13 +7365,14 @@ const struct flashchip flashchips[] = {
.vendor = "Macronix",
.name = "MX29LV040",
.bustype = BUS_PARALLEL,
- .manufacture_id = MACRONIX_ID,
- .model_id = MACRONIX_MX29LV040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_SHORT_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { MACRONIX_ID, MACRONIX_MX29LV040 } } },
+ },
.block_erasers =
{
{
@@ -6841,13 +7392,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P05-A",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P05A,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P05A } } },
+ { probe_spi_res, { 1, { ST_M25P05A_RES } } },
+ },
.block_erasers =
{
{
@@ -6874,13 +7427,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P05",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P05_RES,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ .probers =
+ {
+ { probe_spi_res, { 1, { ST_M25P05_RES } } },
+ },
.block_erasers =
{
{
@@ -6902,13 +7456,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P10-A",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P10A,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, {ST_ID, ST_M25P10A } } },
+ { probe_spi_res, { 1, { ST_M25P10_RES } } },
+ },
.block_erasers =
{
{
@@ -6931,13 +7487,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P10",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P10_RES,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ .probers =
+ {
+ { probe_spi_res, { 1, { ST_M25P10_RES } } },
+ },
.block_erasers =
{
{
@@ -6959,13 +7516,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST", /* Numonyx */
.name = "M25P20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, {ST_ID, ST_M25P20 } } },
+ { probe_spi_res, { 1, {ST_ID, ST_M25P20_RES } } },
+ },
.block_erasers =
{
{
@@ -6987,13 +7546,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P20-old",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P20_RES,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res1,
+ .probers =
+ {
+ { probe_spi_res, { 1, {ST_ID, ST_M25P20 } } },
+ },
.block_erasers =
{
{
@@ -7015,13 +7575,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST", /* Numonyx */
.name = "M25P40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, {ST_ID, ST_M25P40 } } },
+ { probe_spi_res, { 1, {ST_ID, ST_M25P40_RES } } },
+ },
.block_erasers =
{
{
@@ -7043,13 +7605,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P40-old",
.bustype = BUS_SPI,
- .manufacture_id = 0, /* Not used. */
- .model_id = ST_M25P40_RES,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res1,
+ .probers =
+ {
+ { probe_spi_res, { 1, { ST_M25P40_RES } } },
+ },
.block_erasers =
{
{
@@ -7070,13 +7633,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P80 } } },
+ },
.block_erasers =
{
{
@@ -7098,13 +7662,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P16 } } },
+ },
.block_erasers =
{
{
@@ -7126,13 +7691,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P32",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P32 } } },
+ },
.block_erasers =
{
{
@@ -7154,13 +7720,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P64",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P64 } } },
+ },
.block_erasers =
{
{
@@ -7182,13 +7749,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25P128",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25P128,
.total_size = 16384,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25P128 } } },
+ },
.block_erasers =
{
{
@@ -7210,13 +7778,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PE10",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PE10 } } },
+ },
.block_erasers =
{
{
@@ -7241,13 +7810,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PE20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PE20 } } },
+ },
.block_erasers =
{
{
@@ -7272,13 +7842,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PE40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PE40 } } },
+ },
.block_erasers =
{
{
@@ -7303,13 +7874,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PE80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PE80 } } },
+ },
.block_erasers =
{
{
@@ -7334,13 +7906,14 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PE16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PE16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PE16 } } },
+ },
.block_erasers =
{
{
@@ -7365,14 +7938,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PX80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX80,
.total_size = 1024,
.page_size = 256,
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PX80 } } },
+ },
.block_erasers = {
{
.eraseblocks = { { 4 * 1024, 256 } },
@@ -7396,14 +7970,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PX16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX16,
.total_size = 2048,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PX16 } } },
+ },
.block_erasers =
{
{
@@ -7428,14 +8003,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PX32",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX32,
.total_size = 4096,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PX32 } } },
+ },
.block_erasers =
{
{
@@ -7460,14 +8036,15 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M25PX64",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M25PX64,
.total_size = 8192,
.page_size = 256,
/* OTP: 64B total; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M25PX64 } } },
+ },
.block_erasers =
{
{
@@ -7492,12 +8069,13 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M45PE10",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE10,
.total_size = 128,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M45PE10 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 512} },
@@ -7518,12 +8096,13 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M45PE20",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE20,
.total_size = 256,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M45PE20 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 1024} },
@@ -7544,12 +8123,13 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M45PE40",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE40,
.total_size = 512,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M45PE40 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 2048} },
@@ -7570,12 +8150,13 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M45PE80",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE80,
.total_size = 1024,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M45PE80 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 4096} },
@@ -7596,12 +8177,13 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "M45PE16",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_M45PE16,
.total_size = 2048,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_M45PE16 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 8192} },
@@ -7622,15 +8204,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q016",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q016__1E,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q016__1E } } },
+ },
.block_erasers =
{
{
@@ -7658,15 +8241,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q032..1E",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q032__1E,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q032__1E } } },
+ },
.block_erasers =
{
{
@@ -7691,15 +8275,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q032..3E",
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q032__3E,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q032__3E } } },
+ },
.block_erasers =
{
{
@@ -7724,15 +8309,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q064..1E", /* ..1E = 1.8V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q064__1E,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q064__1E } } },
+ },
.block_erasers =
{
{
@@ -7757,15 +8343,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q064..3E", /* ..3E = 3V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q064__3E,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q064__3E } } },
+ },
.block_erasers =
{
{
@@ -7790,15 +8377,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q128..1E", /* ..1E = 1.8V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q128__1E,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q128__1E } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 4096 } },
@@ -7822,15 +8410,16 @@ const struct flashchip flashchips[] = {
.vendor = "Micron/Numonyx/ST",
.name = "N25Q128..3E", /* ..3E = 3V, uniform 64KB/4KB blocks/sectors */
.bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = ST_N25Q128__3E,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 64B total; read 0x4B, write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { ST_ID, ST_N25Q128__3E } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 4096 } },
@@ -7854,13 +8443,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29C51000B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51000B,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29C51000B } } },
+ },
.block_erasers =
{
{
@@ -7880,13 +8470,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29C51000T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51000T,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29C51000T } } },
+ },
.block_erasers =
{
{
@@ -7906,13 +8497,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29C51400B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51400B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29C51400B } } },
+ },
.block_erasers =
{
{
@@ -7932,13 +8524,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29C51400T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29C51400T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29C51400T } } },
+ },
.block_erasers =
{
{
@@ -7958,13 +8551,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29LC51000",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51000,
.total_size = 64,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29LC51000 } } },
+ },
.block_erasers =
{
{
@@ -7984,13 +8578,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29LC51001",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51001,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29LC51001 } } },
+ },
.block_erasers =
{
{
@@ -8010,13 +8605,14 @@ const struct flashchip flashchips[] = {
.vendor = "MoselVitelic",
.name = "V29LC51002",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = MVC_V29LC51002,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, MVC_V29LC51002 } } },
+ },
.block_erasers =
{
{
@@ -8036,13 +8632,14 @@ const struct flashchip flashchips[] = {
.vendor = "Nantronics",
.name = "N25S10",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S10 } } },
+ },
.block_erasers =
{
{
@@ -8076,13 +8673,14 @@ const struct flashchip flashchips[] = {
.vendor = "Nantronics",
.name = "N25S20",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S20 } } },
+ },
.block_erasers =
{
{
@@ -8116,13 +8714,14 @@ const struct flashchip flashchips[] = {
.vendor = "Nantronics",
.name = "N25S40",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S40 } } },
+ },
.block_erasers =
{
{
@@ -8156,13 +8755,14 @@ const struct flashchip flashchips[] = {
.vendor = "Nantronics",
.name = "N25S80",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S80 } } },
+ },
.block_erasers =
{
{
@@ -8193,13 +8793,14 @@ const struct flashchip flashchips[] = {
.vendor = "Nantronics",
.name = "N25S16",
.bustype = BUS_SPI,
- .manufacture_id = NANTRONICS_ID_NOPREFIX,
- .model_id = NANTRONICS_N25S16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { NANTRONICS_ID_NOPREFIX, NANTRONICS_N25S16 } } },
+ },
.block_erasers =
{
{
@@ -8227,13 +8828,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LD256C",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD256C,
.total_size = 32,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LD256C } } },
+ },
.block_erasers =
{
{
@@ -8263,13 +8865,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LD512(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LD512 } } },
+ },
.block_erasers =
{
{
@@ -8300,13 +8903,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LD010(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LD010 } } },
+ },
.block_erasers =
{
{
@@ -8337,13 +8941,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LD020(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LD020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LD020 } } },
+ },
.block_erasers =
{
{
@@ -8374,13 +8979,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LD040(C)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV040 } } },
+ },
.block_erasers =
{
{
@@ -8411,13 +9017,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV512(A)",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM25LV512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2, /* The continuation code is transferred as the 3rd byte m( */
+ .probers =
+ {
+ { probe_spi_res, { 2, { PMC_ID_NOPREFIX, PMC_PM25LV512 } } }, /* The continuation code is transferred as the 3rd byte m( */
+ },
.block_erasers =
{
{
@@ -8442,13 +9049,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV010",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM25LV010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2, /* The continuation code is transferred as the 3rd byte m( */
+ .probers =
+ {
+ { probe_spi_res, { 2, { PMC_ID_NOPREFIX, PMC_PM25LV010 } } }, /* The continuation code is transferred as the 3rd byte m( */
+ },
.block_erasers =
{
{
@@ -8473,13 +9081,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV010A",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV010 } } },
+ },
.block_erasers =
{
{
@@ -8504,13 +9113,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV020",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV020 } } },
+ },
.block_erasers =
{
{
@@ -8535,13 +9145,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV040",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV040 } } },
+ },
.block_erasers =
{
{
@@ -8566,13 +9177,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV080B",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV080B,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV080B } } },
+ },
.block_erasers =
{
{
@@ -8603,13 +9215,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm25LV016B",
.bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = PMC_PM25LV016B,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { PMC_ID, PMC_PM25LV016B } } },
+ },
.block_erasers =
{
{
@@ -8640,13 +9253,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm29F002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM29F002T,
.total_size = 256,
.page_size = 8 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM29F002T } } },
+ },
.block_erasers =
{
{
@@ -8671,13 +9285,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM29F002B,
.total_size = 256,
.page_size = 8 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM29F002B } } },
+ },
.block_erasers =
{
{
@@ -8702,13 +9317,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm39LV010",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39F010, /* Pm39LV010 and Pm39F010 have identical IDs but different voltage */
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM39F010 } } }, /* Pm39LV010 and Pm39F010 have identical IDs but different voltage */
+ },
.block_erasers =
{
{
@@ -8731,13 +9347,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm39LV020",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM39LV020 } } },
+ },
.block_erasers =
{
{
@@ -8760,13 +9377,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm39LV040",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM39LV040 } } },
+ },
.block_erasers =
{
{
@@ -8789,13 +9407,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm39LV512",
.bustype = BUS_PARALLEL,
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM39LV512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { PMC_ID_NOPREFIX, PMC_PM39LV512 } } },
+ },
.block_erasers =
{
{
@@ -8818,13 +9437,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm49FL002",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM49FL002,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { PMC_ID_NOPREFIX, PMC_PM49FL002 } } },
+ },
.block_erasers =
{
{
@@ -8848,13 +9468,14 @@ const struct flashchip flashchips[] = {
.vendor = "PMC",
.name = "Pm49FL004",
.bustype = BUS_LPC | BUS_FWH, /* A/A Mux */
- .manufacture_id = PMC_ID_NOPREFIX,
- .model_id = PMC_PM49FL004,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { PMC_ID_NOPREFIX, PMC_PM49FL004 } } },
+ },
.block_erasers =
{
{
@@ -8878,13 +9499,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW106",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW106,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FW106 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {2 * 1024, 64} },
@@ -8908,13 +9530,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW406A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW406A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FW406A } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 128} },
@@ -8938,13 +9561,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FU406B",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FU406B,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FU406B } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 128} },
@@ -8968,12 +9592,13 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW203A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW203A,
.total_size = 256,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SANYO_ID, SANYO_LE25FW203A } } },
+ },
.block_erasers =
{
{
@@ -8998,12 +9623,13 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW403A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW403A,
.total_size = 512,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SANYO_ID, SANYO_LE25FW403A } } },
+ },
.block_erasers = {
{
.eraseblocks = { {256, 2 * 1024} },
@@ -9027,13 +9653,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW418A",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW418A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FW418A } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 128} },
@@ -9057,13 +9684,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW806",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW806,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FW806 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 256} },
@@ -9090,13 +9718,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sanyo",
.name = "LE25FW808",
.bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = SANYO_LE25FW808,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SANYO_ID, SANYO_LE25FW808 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {8 * 1024, 128} },
@@ -9120,12 +9749,13 @@ const struct flashchip flashchips[] = {
.vendor = "Sharp",
.name = "LH28F008BJT-BTLZ1",
.bustype = BUS_PARALLEL,
- .manufacture_id = SHARP_ID,
- .model_id = SHARP_LH28F008BJ__PB,
.total_size = 1024,
.page_size = 64 * 1024,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SHARP_ID, SHARP_LH28F008BJ__PB } } },
+ },
.block_erasers =
{
{
@@ -9149,13 +9779,14 @@ const struct flashchip flashchips[] = {
.vendor = "Sharp",
.name = "LHF00L04",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SHARP_ID,
- .model_id = SHARP_LHF00L04,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SHARP_ID, SHARP_LHF00L04 } } },
+ },
.block_erasers =
{
{
@@ -9181,13 +9812,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL004A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL004A,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL004A } } },
+ },
.block_erasers =
{
{
@@ -9209,13 +9841,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL008A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL008A,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PRE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL008A } } },
+ },
.block_erasers =
{
{
@@ -9237,13 +9870,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL016A",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL016A,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PR,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL016A } } },
+ },
.block_erasers =
{
{
@@ -9265,13 +9899,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL032A/P",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL032A,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL032A } } },
+ },
.block_erasers =
{
{
@@ -9293,13 +9928,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL064A/P",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL064A,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL064A } } },
+ },
.block_erasers =
{
{
@@ -9321,13 +9957,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL204K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL204,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL204 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 128} },
@@ -9354,13 +9991,14 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL208K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL208,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL208 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 256} },
@@ -9387,14 +10025,15 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL116K/S25FL216K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL216,
.total_size = 2048,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (S25FL116K only) */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL216 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 512} },
@@ -9421,14 +10060,15 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL132K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL132K,
.total_size = 4096,
.page_size = 256,
/* OTP: 768B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL132K } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 1024} },
@@ -9455,14 +10095,15 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL164K",
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL164K,
.total_size = 8192,
.page_size = 256,
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL164K } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 2048} },
@@ -9489,15 +10130,16 @@ const struct flashchip flashchips[] = {
.vendor = "Spansion",
.name = "S25FL128S......0", /* uniform 256kB sectors */
.bustype = BUS_SPI,
- .manufacture_id = SPANSION_ID,
- .model_id = SPANSION_S25FL128,
.total_size = 16384,
.page_size = 256,
/* supports 4B addressing */
/* OTP: 1024B total, 32B reserved; read 0x4B; write 0x42 */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SPANSION_ID, SPANSION_S25FL128 } } },
+ },
.block_erasers = {
{
.eraseblocks = { {4 * 1024, 4096} },
@@ -9524,13 +10166,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25LF020A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020_REMS,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 2, { SST_ID, SST_SST25VF020_REMS } } },
+ },
.block_erasers =
{
{
@@ -9555,13 +10198,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25LF040A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SST_ID, SST_SST25VF040_REMS } } },
+ },
.block_erasers =
{
{
@@ -9586,13 +10230,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25LF080(A)",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF080_REMS,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_res2,
+ .probers =
+ {
+ { probe_spi_res, { 2, { SST_ID, SST_SST25VF080_REMS } } },
+ },
.block_erasers =
{
{
@@ -9617,13 +10262,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF512A",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF512A_REMS,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 3, { SST_ID, SST_SST25VF512A_REMS } } },
+ },
.block_erasers =
{
{
@@ -9654,13 +10300,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF010",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF010_REMS,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 3, { SST_ID, SST_SST25VF010_REMS } } },
+ },
.block_erasers =
{
{
@@ -9691,13 +10338,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF020",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020_REMS,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 3, { SST_ID, SST_SST25VF020_REMS } } },
+ },
.block_erasers =
{
{
@@ -9722,13 +10370,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF020B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF020B,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF020B } } },
+ },
.block_erasers =
{
{
@@ -9759,13 +10408,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF040",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PR,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 3, { SST_ID, SST_SST25VF040_REMS } } },
+ },
.block_erasers =
{
{
@@ -9790,13 +10440,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF040B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040B,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF040B } } },
+ },
.block_erasers =
{
{
@@ -9827,13 +10478,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF040B.REMS",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF040B_REMS,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rems,
+ .probers =
+ {
+ { probe_spi_rems, { 3, { SST_ID, SST_SST25VF040B_REMS } } },
+ },
.block_erasers =
{
{
@@ -9864,13 +10516,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF080B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF080B,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF080B } } },
+ },
.block_erasers =
{
{
@@ -9901,13 +10554,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF016B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF016B,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF016B } } },
+ },
.block_erasers =
{
{
@@ -9938,13 +10592,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF032B",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF032B,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF032B } } },
+ },
.block_erasers =
{
{
@@ -9975,13 +10630,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25VF064C",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25VF064C,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EWSR,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25VF064C } } },
+ },
.block_erasers =
{
{
@@ -10012,13 +10668,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25WF512",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF512,
.total_size = 64,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25WF512 } } },
+ },
.block_erasers =
{
{
@@ -10046,13 +10703,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25WF010",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF010,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25WF010 } } },
+ },
.block_erasers =
{
{
@@ -10080,13 +10738,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25WF020",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF020,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25WF020 } } },
+ },
.block_erasers =
{
{
@@ -10117,13 +10776,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25WF040",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF040,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25WF040 } } },
+ },
.block_erasers =
{
{
@@ -10154,13 +10814,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST25WF080",
.bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = SST_SST25WF080,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_EITHER,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { SST_ID, SST_SST25WF080 } } },
+ },
.block_erasers =
{
{
@@ -10191,13 +10852,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST28SF040A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST28SF040,
.total_size = 512,
.page_size = 256,
.feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SST_ID, SST_SST28SF040 } } },
+ },
.block_erasers =
{
{
@@ -10218,13 +10880,13 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST29EE010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29EE010,
.total_size = 128,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { SST_ID, SST_SST29EE010 } } },
+ },
.block_erasers =
{
{
@@ -10241,13 +10903,13 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST29LE010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29LE010,
.total_size = 128,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { SST_ID, SST_SST29LE010 } } },
+ },
.block_erasers =
{
{
@@ -10264,13 +10926,13 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST29EE020A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29EE020A,
.total_size = 256,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { SST_ID, SST_SST29EE020A } } },
+ },
.block_erasers =
{
{
@@ -10287,13 +10949,13 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST29LE020",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST29LE020,
.total_size = 256,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { SST_ID, SST_SST29LE020 } } },
+ },
.block_erasers =
{
{
@@ -10310,13 +10972,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39SF512",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39SF512 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10336,13 +10999,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39SF010A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF010,
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39SF010 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10362,13 +11026,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39SF020A",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39SF020 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10388,13 +11053,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39SF040",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39SF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39SF040 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10414,13 +11080,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39VF512",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF512,
.total_size = 64,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39VF512 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10440,13 +11107,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39VF010",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF010,
.total_size = 128,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39VF010 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10466,13 +11134,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39VF020",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF020,
.total_size = 256,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39VF020 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10492,13 +11161,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39VF040",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39VF040 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10518,13 +11188,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST39VF080",
.bustype = BUS_PARALLEL,
- .manufacture_id = SST_ID,
- .model_id = SST_SST39VF080,
.total_size = 1024,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST39VF080 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10547,13 +11218,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF002A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF002A,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF002A } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10578,13 +11250,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF003A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF003A,
.total_size = 384,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF003A } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10612,13 +11285,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF004A/B",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF004A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF004A } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10643,13 +11317,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF004C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF004C,
.total_size = 512,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SST_ID, SST_SST49LF004C } } },
+ },
.block_erasers =
{
{
@@ -10675,13 +11350,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF008A",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF008A,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF008A } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10706,13 +11382,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF008C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF008C,
.total_size = 1024,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SST_ID, SST_SST49LF008C } } },
+ },
.block_erasers =
{
{
@@ -10738,13 +11415,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF016C",
.bustype = BUS_FWH,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF016C,
.total_size = 2048,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SST_ID, SST_SST49LF016C } } },
+ },
.block_erasers =
{
{
@@ -10770,13 +11448,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF020",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF020,
.total_size = 256,
.page_size = 16 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF020 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10799,13 +11478,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF020A",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF020A,
.total_size = 256,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PRE,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF020A } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10828,13 +11508,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF040",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF040,
.total_size = 512,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF040 } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10857,13 +11538,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF040B",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET | FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* 150 ns */
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF040B } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10887,13 +11569,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF080A",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF080A,
.total_size = 1024,
.page_size = 4096,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SST_ID, SST_SST49LF080A } } },
+ },
.block_erasers =
{
{
@@ -10916,13 +11599,14 @@ const struct flashchip flashchips[] = {
.vendor = "SST",
.name = "SST49LF160C",
.bustype = BUS_LPC,
- .manufacture_id = SST_ID,
- .model_id = SST_SST49LF160C,
.total_size = 2048,
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { SST_ID, SST_SST49LF160C } } },
+ },
.block_erasers =
{
{
@@ -10948,13 +11632,13 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29F002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F002B,
.total_size = 256,
.page_size = 64 * 1024,
- .feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_aaa, { 2, { ST_ID, ST_M29F002B } } }, /* 150 ns */
+ },
.block_erasers =
{
{
@@ -10979,13 +11663,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29F002T/NT",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F002T,
.total_size = 256,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_AAA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_aaa, { 2, { ST_ID, ST_M29F002T } } },
+ },
.block_erasers =
{
{
@@ -11010,13 +11695,13 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29F040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F040B,
.total_size = 512,
.page_size = 64 * 1024,
- .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { ST_ID, ST_M29F040B } } },
+ },
.block_erasers =
{
{
@@ -11037,12 +11722,13 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29F400BB",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F400BB,
.total_size = 512,
.page_size = 64 * 1024,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 3, { ST_ID, ST_M29F400BB } } },
+ },
.block_erasers =
{
{
@@ -11062,17 +11748,19 @@ const struct flashchip flashchips[] = {
.read = read_memmapped,
.voltage = {4500, 5500},
},
+
{
/* FIXME: this has WORD/BYTE sequences; 2AA for word, 555 for byte */
.vendor = "ST",
.name = "M29F400BT",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29F400BT,
.total_size = 512,
.page_size = 64 * 1024,
.tested = TEST_UNTESTED,
- .probe = probe_m29f400bt,
+ .probers =
+ {
+ { probe_m29f400bt, { 2, { ST_ID, ST_M29F400BT } } },
+ },
.block_erasers =
{
{
@@ -11097,13 +11785,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29W010B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W010B,
.total_size = 128,
.page_size = 16 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { ST_ID, ST_M29W010B } } },
+ },
.block_erasers =
{
{
@@ -11123,13 +11812,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29W040B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { ST_ID, ST_M29W040B } } },
+ },
.block_erasers =
{
{
@@ -11149,13 +11839,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M29W512B",
.bustype = BUS_PARALLEL,
- .manufacture_id = ST_ID,
- .model_id = ST_M29W512B,
.total_size = 64,
.page_size = 64 * 1024,
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { ST_ID, ST_M29W512B } } },
+ },
.block_erasers =
{
{
@@ -11172,13 +11863,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FLW040A",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW040A,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FLW040A } } },
+ },
.block_erasers =
{
{
@@ -11204,13 +11896,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FLW040B",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW040B,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FLW040B } } },
+ },
.block_erasers =
{
{
@@ -11236,13 +11929,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FLW080A",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW080A,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FLW080A } } },
+ },
.block_erasers =
{
{
@@ -11268,13 +11962,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FLW080B",
.bustype = BUS_FWH | BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FLW080B,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FLW080B } } },
+ },
.block_erasers =
{
{
@@ -11300,13 +11995,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FW002",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW002,
.total_size = 256,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FW002 } } },
+ },
.block_erasers =
{
{
@@ -11329,13 +12025,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FW016",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW016,
.total_size = 2048,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FW016 } } },
+ },
.block_erasers =
{
{
@@ -11353,13 +12050,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FW040",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW040,
.total_size = 512,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FW040 } } },
+ },
.block_erasers =
{
{
@@ -11377,13 +12075,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50FW080",
.bustype = BUS_FWH, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50FW080,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50FW080 } } },
+ },
.block_erasers =
{
{
@@ -11401,13 +12100,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50LPW080",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50LPW080,
.total_size = 1024,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50LPW080 } } },
+ },
.block_erasers =
{
{
@@ -11425,13 +12125,14 @@ const struct flashchip flashchips[] = {
.vendor = "ST",
.name = "M50LPW116",
.bustype = BUS_LPC, /* A/A Mux */
- .manufacture_id = ST_ID,
- .model_id = ST_M50LPW116,
.total_size = 2048,
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab_unshifted,
+ .probers =
+ {
+ { probe_82802ab_unshifted, { 3, { ST_ID, ST_M50LPW116 } } },
+ },
.block_erasers =
{
{
@@ -11455,13 +12156,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51001B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51001B,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51001B } } },
+ },
.block_erasers =
{
{
@@ -11481,13 +12183,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51001T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51001T,
.total_size = 128,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51001T } } },
+ },
.block_erasers =
{
{
@@ -11507,13 +12210,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51002B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51002B,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51002B } } },
+ },
.block_erasers =
{
{
@@ -11532,13 +12236,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51002T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51002T,
.total_size = 256,
.page_size = 512,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51002T } } },
+ },
.block_erasers =
{
{
@@ -11557,13 +12262,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51004B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51004B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51004B } } },
+ },
.block_erasers =
{
{
@@ -11583,13 +12289,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{F,S,V}29C51004T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C51004T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C51004T } } },
+ },
.block_erasers =
{
{
@@ -11609,13 +12316,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{S,V}29C31004B",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C31004B,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C31004B } } },
+ },
.block_erasers =
{
{
@@ -11635,13 +12343,14 @@ const struct flashchip flashchips[] = {
.vendor = "SyncMOS/MoselVitelic",
.name = "{S,V}29C31004T",
.bustype = BUS_PARALLEL,
- .manufacture_id = SYNCMOS_MVC_ID,
- .model_id = SM_MVC_29C31004T,
.total_size = 512,
.page_size = 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { SYNCMOS_MVC_ID, SM_MVC_29C31004T } } },
+ },
.block_erasers =
{
{
@@ -11661,13 +12370,14 @@ const struct flashchip flashchips[] = {
.vendor = "TI",
.name = "TMS29F002RB",
.bustype = BUS_PARALLEL,
- .manufacture_id = TI_OLD_ID,
- .model_id = TI_TMS29F002RB,
.total_size = 256,
.page_size = 16384, /* Non-uniform sectors */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { TI_OLD_ID, TI_TMS29F002RB } } },
+ },
.block_erasers =
{
{
@@ -11692,13 +12402,14 @@ const struct flashchip flashchips[] = {
.vendor = "TI",
.name = "TMS29F002RT",
.bustype = BUS_PARALLEL,
- .manufacture_id = TI_OLD_ID,
- .model_id = TI_TMS29F002RT,
.total_size = 256,
.page_size = 16384, /* Non-uniform sectors */
.feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_2aa, { 2, { TI_OLD_ID, TI_TMS29F002RT } } },
+ },
.block_erasers =
{
{
@@ -11723,15 +12434,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q80.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q80_V,
.total_size = 1024,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q80_V } } },
+ },
.block_erasers =
{
{
@@ -11762,15 +12474,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q16.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q16_V,
.total_size = 2048,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q16_V } } },
+ },
.block_erasers =
{
{
@@ -11801,15 +12514,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q32.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q32_V,
.total_size = 4096,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q32_V } } },
+ },
.block_erasers =
{
{
@@ -11840,15 +12554,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q64.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q64_V,
.total_size = 8192,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q64_V } } },
+ },
.block_erasers =
{
{
@@ -11879,15 +12594,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q128.V",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q128_V,
.total_size = 16384,
.page_size = 256,
/* supports SFDP */
/* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q128_V } } },
+ },
.block_erasers =
{
{
@@ -11918,14 +12634,15 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q20.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q20_W,
.total_size = 256,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q20_W } } },
+ },
.block_erasers =
{
{
@@ -11956,14 +12673,15 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q40.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q40_W,
.total_size = 512,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q40_W } } },
+ },
.block_erasers =
{
{
@@ -11994,14 +12712,15 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q80.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q80_W,
.total_size = 1024,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q80_W } } },
+ },
.block_erasers =
{
{
@@ -12032,15 +12751,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q16.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q16_W,
.total_size = 2048,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_UNTESTED,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q16_W } } },
+ },
.block_erasers =
{
{
@@ -12071,15 +12791,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q32.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q32_W,
.total_size = 4096,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q32_W } } },
+ },
.block_erasers =
{
{
@@ -12110,15 +12831,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25Q64.W",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25Q64_W,
.total_size = 8192,
.page_size = 256,
/* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */
/* QPI enable 0x38, disable 0xFF */
.feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25Q64_W } } },
+ },
.block_erasers =
{
{
@@ -12149,13 +12871,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X10",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X10,
.total_size = 128,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X10 } } },
+ },
.block_erasers =
{
{
@@ -12180,13 +12903,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X20",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X20,
.total_size = 256,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X20 } } },
+ },
.block_erasers =
{
{
@@ -12211,13 +12935,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X40",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X40,
.total_size = 512,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X40 } } },
+ },
.block_erasers =
{
{
@@ -12242,13 +12967,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X80",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X80,
.total_size = 1024,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X80 } } },
+ },
.block_erasers =
{
{
@@ -12273,13 +12999,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X16",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X16,
.total_size = 2048,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X16 } } },
+ { probe_spi_res, { 2, { WINBOND_NEX_ID, 0x14 } } },
+ { probe_spi_rems, { 2, { WINBOND_NEX_ID, 0x14 } } },
+ },
.block_erasers =
{
{
@@ -12310,13 +13039,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X32",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X32,
.total_size = 4096,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PREW,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X32 } } },
+ { probe_spi_res, { 2, { WINBOND_NEX_ID, 0x15 } } },
+ { probe_spi_rems, { 2, { WINBOND_NEX_ID, 0x15 } } },
+ },
.block_erasers =
{
{
@@ -12347,13 +13079,16 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W25X64",
.bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = WINBOND_NEX_W25X64,
.total_size = 8192,
.page_size = 256,
.feature_bits = FEATURE_WRSR_WREN,
.tested = TEST_OK_PROBE,
- .probe = probe_spi_rdid,
+ .probers =
+ {
+ { probe_spi_rdid, { 3, { WINBOND_NEX_ID, WINBOND_NEX_W25X64 } } },
+ { probe_spi_res, { 2, { WINBOND_NEX_ID, 0x16 } } },
+ { probe_spi_rems, { 2, { WINBOND_NEX_ID, 0x16 } } },
+ },
.block_erasers =
{
{
@@ -12384,12 +13119,13 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W29C010(M)/W29C011A/W29EE011/W29EE012-old",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C010,
.total_size = 128,
.page_size = 128,
.tested = TEST_OK_PREW,
- .probe = probe_w29ee011,
+ .probers =
+ {
+ { probe_w29ee011, { 2, { WINBOND_ID, WINBOND_W29C010 } } },
+ },
.block_erasers =
{
{
@@ -12405,13 +13141,13 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W29C010(M)/W29C011A/W29EE011/W29EE012",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C010,
.total_size = 128,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec, /* used datasheet for the W29C011A */
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { WINBOND_ID, WINBOND_W29C010 } } }, /* used datasheet for the W29C011A */
+ },
.block_erasers =
{
{
@@ -12427,13 +13163,13 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W29C020(C)/W29C022",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C020,
.total_size = 256,
.page_size = 128,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { WINBOND_ID, WINBOND_W29C020 } } },
+ },
.block_erasers =
{
{
@@ -12450,13 +13186,13 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W29C040/P",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W29C040,
.total_size = 512,
.page_size = 256,
- .feature_bits = FEATURE_LONG_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_longreset, { 3, { WINBOND_ID, WINBOND_W29C040 } } },
+ },
.block_erasers =
{
{
@@ -12473,13 +13209,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39F010",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39F010,
.total_size = 128,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39F010 } } },
+ },
.block_erasers =
{
{
@@ -12500,13 +13237,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39L010",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L010,
.total_size = 128,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39L010 } } },
+ },
.block_erasers =
{
{
@@ -12527,13 +13265,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39L020",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L020,
.total_size = 256,
.page_size = 4 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39L020 } } },
+ },
.block_erasers =
{
{
@@ -12557,13 +13296,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39L040",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39L040,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PR,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39L040 } } },
+ },
.block_erasers =
{
{
@@ -12587,13 +13327,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040A,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040A } } },
+ },
.block_erasers =
{
{
@@ -12614,13 +13355,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040B",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040B } } },
+ },
.block_erasers =
{
{
@@ -12641,13 +13383,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040C",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040C,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040C } } },
+ },
.block_erasers =
{
{
@@ -12668,13 +13411,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040FA,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040FA } } },
+ },
.block_erasers =
{
{
@@ -12699,13 +13443,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040FB",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040B,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040B } } },
+ },
.block_erasers =
{
{
@@ -12727,13 +13472,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V040FC",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V040C,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V040C } } },
+ },
.block_erasers =
{
{
@@ -12754,13 +13500,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V080A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080A,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V080A } } },
+ },
.block_erasers =
{
{
@@ -12781,13 +13528,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W49F002U/N",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49F002U,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W49F002U } } },
+ },
.block_erasers =
{
{
@@ -12812,13 +13560,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W49F020",
.bustype = BUS_PARALLEL,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49F020,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PROBE,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W49F020 } } },
+ },
.block_erasers =
{
{
@@ -12835,13 +13584,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W49V002A",
.bustype = BUS_LPC,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49V002A,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W49V002A } } },
+ },
.block_erasers =
{
{
@@ -12866,13 +13616,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W49V002FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W49V002FA,
.total_size = 256,
.page_size = 128,
.feature_bits = FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W49V002FA } } },
+ },
.block_erasers =
{
{
@@ -12897,13 +13648,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V080FA",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080FA,
.total_size = 1024,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_OK_PREW,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V080FA } } },
+ },
.block_erasers =
{
{
@@ -12925,13 +13677,14 @@ const struct flashchip flashchips[] = {
.vendor = "Winbond",
.name = "W39V080FA (dual mode)",
.bustype = BUS_FWH,
- .manufacture_id = WINBOND_ID,
- .model_id = WINBOND_W39V080FA_DM,
.total_size = 512,
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET,
.tested = TEST_UNTESTED,
- .probe = probe_jedec,
+ .probers =
+ {
+ { probe_jedec_shortreset_full, { 2, { WINBOND_ID, WINBOND_W39V080FA_DM } } },
+ },
.block_erasers =
{
{
@@ -12947,203 +13700,6 @@ const struct flashchip flashchips[] = {
.read = read_memmapped,
.voltage = {3000, 3600}, /* Also has 12V fast program */
},
-
- {
- .vendor = "Unknown",
- .name = "SFDP-capable chip",
- .bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = SFDP_DEVICE_ID,
- /* We present our own "report this" text hence we do not
- * want the default "This flash part has status UNTESTED..."
- * text to be printed. */
- .tested = TEST_OK_PREW,
- .probe = probe_spi_sfdp,
- .unlock = spi_disable_blockprotect, /* is this safe? */
- .read = spi_chip_read,
- /* FIXME: some vendor extensions define this */
- .voltage = {0},
- /* Everything below will be set by the probing function. */
- .write = NULL,
- .total_size = 0,
- .page_size = 0,
- .feature_bits = 0,
- .block_erasers = {},
- },
-
- {
- .vendor = "Programmer",
- .name = "Opaque flash chip",
- .bustype = BUS_PROG,
- .manufacture_id = PROGMANUF_ID,
- .model_id = PROGDEV_ID,
- .total_size = 0,
- .page_size = 256,
- /* probe is assumed to work, rest will be filled in by probe */
- .tested = TEST_OK_PROBE,
- .probe = probe_opaque,
- /* eraseblock sizes will be set by the probing function */
- .block_erasers =
- {
- {
- .block_erase = erase_opaque,
- }
- },
- .write = write_opaque,
- .read = read_opaque,
- },
-
- {
- .vendor = "AMIC",
- .name = "unknown AMIC SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = AMIC_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid4,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Atmel",
- .name = "unknown Atmel SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = ATMEL_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Eon",
- .name = "unknown Eon SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = EON_ID_NOPREFIX,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Macronix",
- .name = "unknown Macronix SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = MACRONIX_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "PMC",
- .name = "unknown PMC SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = PMC_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "SST",
- .name = "unknown SST SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = SST_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "ST",
- .name = "unknown ST SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = ST_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Sanyo",
- .name = "unknown Sanyo SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = SANYO_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Winbond",
- .name = "unknown Winbond (ex Nexcom) SPI chip",
- .bustype = BUS_SPI,
- .manufacture_id = WINBOND_NEX_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- .read = NULL,
- },
-
- {
- .vendor = "Generic",
- .name = "unknown SPI chip (RDID)",
- .bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rdid,
- .write = NULL,
- },
-
- {
- .vendor = "Generic",
- .name = "unknown SPI chip (REMS)",
- .bustype = BUS_SPI,
- .manufacture_id = GENERIC_MANUF_ID,
- .model_id = GENERIC_DEVICE_ID,
- .total_size = 0,
- .page_size = 256,
- .tested = TEST_BAD_PREW,
- .probe = probe_spi_rems,
- .write = NULL,
- },
{0}
};
diff --git a/flashchips.h b/flashchips.h
index fb17981..5be232c 100644
--- a/flashchips.h
+++ b/flashchips.h
@@ -34,13 +34,7 @@
* SPI parts have 16-bit device IDs if they support RDID.
*/
-#define GENERIC_MANUF_ID 0xFFFF /* Check if there is a vendor ID */
-#define GENERIC_DEVICE_ID 0xFFFF /* Only match the vendor ID */
-#define SFDP_DEVICE_ID 0xFFFE
-#define PROGMANUF_ID 0xFFFE /* dummy ID for opaque chips behind a programmer */
-#define PROGDEV_ID 0x01 /* dummy ID for opaque chips behind a programmer */
-
-#define ALLIANCE_ID 0x52 /* Alliance Semiconductor */
+#define ALLIANCE_ID 0x52 /* Alliance Semiconductor */
#define ALLIANCE_AS29F002B 0x34
#define ALLIANCE_AS29F002T 0xB0
#define ALLIANCE_AS29F010 0x04
@@ -54,17 +48,17 @@
#define ALLIANCE_AS29LV800B 0x5B
#define ALLIANCE_AS29LV800T 0xDA
-#define AMD_ID 0x01 /* AMD */
+#define AMD_ID 0x01 /* AMD */
#define AMD_AM29DL400BT 0x0C
#define AMD_AM29DL400BB 0x0F
#define AMD_AM29DL800BT 0x4A
#define AMD_AM29DL800BB 0xCB
-#define AMD_AM29F002BB 0x34 /* Same as Am29F002NBB */
-#define AMD_AM29F002BT 0xB0 /* Same as Am29F002NBT */
+#define AMD_AM29F002BB 0x34 /* Same as Am29F002NBB */
+#define AMD_AM29F002BT 0xB0 /* Same as Am29F002NBT */
#define AMD_AM29F004BB 0x7B
#define AMD_AM29F004BT 0x77
#define AMD_AM29F016D 0xAD
-#define AMD_AM29F010B 0x20 /* Same as Am29F010A */
+#define AMD_AM29F010B 0x20 /* Same as Am29F010A */
#define AMD_AM29F040B 0xA4
#define AMD_AM29F080B 0xD5
#define AMD_AM29F200BB 0x57
@@ -82,143 +76,144 @@
#define AMD_AM29LV008BB 0x37
#define AMD_AM29LV008BT 0x3E
#define AMD_AM29LV040B 0x4F
-#define AMD_AM29LV080B 0x38 /* Same as Am29LV081B */
+#define AMD_AM29LV080B 0x38 /* Same as Am29LV081B */
#define AMD_AM29LV200BB 0xBF
#define AMD_AM29LV200BT 0x3B
-#define AMD_AM29LV800BB 0x5B /* Same as Am29LV800DB */
+#define AMD_AM29LV800BB 0x5B /* Same as Am29LV800DB */
#define AMD_AM29LV400BT 0xB9
#define AMD_AM29LV400BB 0xBA
-#define AMD_AM29LV800BT 0xDA /* Same as Am29LV800DT */
-
-#define AMIC_ID 0x7F37 /* AMIC */
-#define AMIC_ID_NOPREFIX 0x37 /* AMIC */
-#define AMIC_A25L05PT 0x2020
-#define AMIC_A25L05PU 0x2010
-#define AMIC_A25L10PT 0x2021
-#define AMIC_A25L10PU 0x2011
-#define AMIC_A25L20PT 0x2022
-#define AMIC_A25L20PU 0x2012
-#define AMIC_A25L40PT 0x2013 /* Datasheet says T and U have
- same device ID. Confirmed by
- hardware testing. */
-#define AMIC_A25L40PU 0x2013
-#define AMIC_A25L80P 0x2014 /* Seems that no A25L80PT exists */
-#define AMIC_A25L16PT 0x2025
-#define AMIC_A25L16PU 0x2015
-#define AMIC_A25L512 0x3010
-#define AMIC_A25L010 0x3011
-#define AMIC_A25L020 0x3012
-#define AMIC_A25L040 0x3013
-#define AMIC_A25L080 0x3014
-#define AMIC_A25L016 0x3015
-#define AMIC_A25L032 0x3016
-#define AMIC_A25LQ16 0x4015
-#define AMIC_A25LQ032 0x4016 /* Same as A25LQ32A, but the latter supports SFDP */
-#define AMIC_A25LQ64 0x4017
+#define AMD_AM29LV800BT 0xDA /* Same as Am29LV800DT */
+
+#define AMIC_ID 0x7F, 0x37 /* AMIC */
+#define AMIC_ID_NOPREFIX 0x37 /* AMIC, without prefix */
+#define AMIC_A25L05PT 0x20, 0x20
+#define AMIC_A25L05PU 0x20, 0x10
+#define AMIC_A25L10PT 0x20, 0x21
+#define AMIC_A25L10PU 0x20, 0x11
+#define AMIC_A25L20PT 0x20, 0x22
+#define AMIC_A25L20PU 0x20, 0x12
+#define AMIC_A25L40PT 0x20, 0x13 /* Datasheet says T and U have same device ID. Confirmed by
+ * hardware testing. */
+#define AMIC_A25L40PU 0x20, 0x13
+#define AMIC_A25L80P 0x20, 0x14 /* Seems that no A25L80PT exists */
+#define AMIC_A25L16PT 0x20, 0x25
+#define AMIC_A25L16PU 0x20, 0x15
+#define AMIC_A25L512 0x30, 0x10
+#define AMIC_A25L010 0x30, 0x11
+#define AMIC_A25L020 0x30, 0x12
+#define AMIC_A25L040 0x30, 0x13
+#define AMIC_A25L080 0x30, 0x14
+#define AMIC_A25L016 0x30, 0x15
+#define AMIC_A25L032 0x30, 0x16
+#define AMIC_A25LQ16 0x40, 0x15
+#define AMIC_A25LQ032 0x40, 0x16 /* Same as A25LQ32A, but the latter supports SFDP */
+#define AMIC_A25LQ64 0x40, 0x17
#define AMIC_A29002B 0x0d
-#define AMIC_A29002T 0x8C /* Same as A290021T */
+#define AMIC_A29002T 0x8C /* Same as A290021T */
#define AMIC_A29040B 0x86
-#define AMIC_A29400T 0xB0 /* Same as 294001T */
-#define AMIC_A29400U 0x31 /* Same as A294001U */
+#define AMIC_A29400T 0xB0 /* Same as 294001T */
+#define AMIC_A29400U 0x31 /* Same as A294001U */
#define AMIC_A29800T 0x0E
#define AMIC_A29800U 0x8F
-#define AMIC_A29L004T 0x34 /* Same as A29L400T */
-#define AMIC_A29L004U 0xB5 /* Same as A29L400U */
-#define AMIC_A29L008T 0x1A /* Same as A29L800T */
-#define AMIC_A29L008U 0x9B /* Same as A29L800U */
+#define AMIC_A29L004T 0x34 /* Same as A29L400T */
+#define AMIC_A29L004U 0xB5 /* Same as A29L400U */
+#define AMIC_A29L008T 0x1A /* Same as A29L800T */
+#define AMIC_A29L008U 0x9B /* Same as A29L800U */
#define AMIC_A29L040 0x92
#define AMIC_A49LF040A 0x9d
-#define ATMEL_ID 0x1F /* Atmel (now used by Adesto) */
-#define ATMEL_AT25DF021 0x4300
-#define ATMEL_AT25DF041A 0x4401
-#define ATMEL_AT25DF081 0x4502 /* EDI 0x00. AT25DL081 has same ID + EDI 0x0100 */
-#define ATMEL_AT25DF081A 0x4501 /* Yes, 81A has a lower number than 81 */
-#define ATMEL_AT25DF161 0x4602
-#define ATMEL_AT25DF321 0x4700 /* Same as 26DF321 */
-#define ATMEL_AT25DF321A 0x4701
-#define ATMEL_AT25DF641 0x4800
-#define ATMEL_AT25DL161 0x4603 /* EDI 0x0100 */
-#define ATMEL_AT25DQ161 0x8600 /* EDI 0x0100 */
-#define ATMEL_AT25DQ321 0x8700 /* EDI 0x0100 */
-#define ATMEL_AT25F512 0x60 /* Needs AT25F_RDID. ID from PCN and actual HW. Seems to be a relabeled AT25F1024. */
-#define ATMEL_AT25F512A 0x65 /* Needs AT25F_RDID */
-#define ATMEL_AT25F512B 0x6500
-#define ATMEL_AT25F1024 0x60 /* Needs AT25F_RDID */
-#define ATMEL_AT25F2048 0x63 /* Needs AT25F_RDID */
-#define ATMEL_AT25F4096 0x64 /* Needs AT25F_RDID */
-#define ATMEL_AT25FS010 0x6601
-#define ATMEL_AT25FS040 0x6604
-#define ATMEL_AT26DF041 0x4400
-#define ATMEL_AT26DF081 0x4500 /* guessed, no datasheet available */
-#define ATMEL_AT26DF081A 0x4501
-#define ATMEL_AT26DF161 0x4600
-#define ATMEL_AT26DF161A 0x4601
-#define ATMEL_AT26DF321 0x4700 /* Same as 25DF321 */
-#define ATMEL_AT26F004 0x0400
+#define ATMEL_ID 0x1F /* Atmel (now used by Adesto) */
+#define ATMEL_AT25DF021 0x43, 0x00
+#define ATMEL_AT25DF041A 0x44, 0x01
+#define ATMEL_AT25DF081 0x45, 0x02 /* EDI 0x00. AT25DL081 has same ID + EDI 0x01, 0x00, */
+#define ATMEL_AT25DF081A 0x45, 0x01 /* Yes, 81A has a lower number than 81 */
+#define ATMEL_AT25DF161 0x46, 0x02
+#define ATMEL_AT25DF321 0x47, 0x00 /* Same as 26DF321 */
+#define ATMEL_AT25DF321A 0x47, 0x01
+#define ATMEL_AT25DF641 0x48, 0x00
+#define ATMEL_AT25DL161 0x46, 0x03 /* EDI 0x01, 0x00, */
+#define ATMEL_AT25DQ161 0x86, 0x00 /* EDI 0x01, 0x00, */
+#define ATMEL_AT25DQ321 0x87, 0x00 /* EDI 0x01, 0x00, */
+#define ATMEL_AT25F512 0x60 /* Needs AT25F_RDID. ID from PCN and actual HW. Seems to be a
+ * relabeled AT25F1024. */
+#define ATMEL_AT25F512A 0x65 /* Needs AT25F_RDID */
+#define ATMEL_AT25F512B 0x65, 0x00
+#define ATMEL_AT25F1024 0x60 /* Needs AT25F_RDID */
+#define ATMEL_AT25F2048 0x63 /* Needs AT25F_RDID */
+#define ATMEL_AT25F4096 0x64 /* Needs AT25F_RDID */
+#define ATMEL_AT25FS010 0x66, 0x01
+#define ATMEL_AT25FS040 0x66, 0x04
+#define ATMEL_AT26DF041 0x44, 0x00
+#define ATMEL_AT26DF081 0x45, 0x00 /* guessed, no datasheet available */
+#define ATMEL_AT26DF081A 0x45, 0x01
+#define ATMEL_AT26DF161 0x46, 0x00
+#define ATMEL_AT26DF161A 0x46, 0x01
+#define ATMEL_AT26DF321 0x47, 0x00 /* Same as 25DF321 */
+#define ATMEL_AT26F004 0x04, 0x00
#define ATMEL_AT29C040A 0xA4
#define ATMEL_AT29C010A 0xD5
#define ATMEL_AT29C020 0xDA
#define ATMEL_AT29C512 0x5D
#define ATMEL_AT45BR3214B /* No ID available */
-#define ATMEL_AT45CS1282 0x2920
+#define ATMEL_AT45CS1282 0x29, 0x20
#define ATMEL_AT45D011 /* No ID available */
#define ATMEL_AT45D021A /* No ID available */
#define ATMEL_AT45D041A /* No ID available */
#define ATMEL_AT45D081A /* No ID available */
#define ATMEL_AT45D161 /* No ID available */
#define ATMEL_AT45DB011 /* No ID (opcode) available for AT45DB011, AT45DB011B */
-#define ATMEL_AT45DB011D 0x2200
+#define ATMEL_AT45DB011D 0x22, 0x00
#define ATMEL_AT45DB021 /* No ID (opcode) available for AT45DB021, AT45DB021A, AT45DB021B */
-#define ATMEL_AT45DB021D 0x2300
-#define ATMEL_AT45DB021E /* same as above but with EDI 0x0100 */
+#define ATMEL_AT45DB021D 0x23, 0x00
+#define ATMEL_AT45DB021E /* same as above but with EDI 0x01, 0x00, */
#define ATMEL_AT45DB041 /* No ID (opcode) available for AT45DB041, AT45DB041A, AT45DB041B */
-#define ATMEL_AT45DB041D 0x2400
-#define ATMEL_AT45DB041E /* same as above but with EDI 0x0100 */
+#define ATMEL_AT45DB041D 0x24, 0x00
+#define ATMEL_AT45DB041E /* same as above but with EDI 0x01, 0x00, */
#define ATMEL_AT45DB081 /* No ID (opcode) available for AT45DB081, AT45DB081A, AT45DB081B */
-#define ATMEL_AT45DB081D 0x2500
-#define ATMEL_AT45DB081E /* same as above but with EDI 0x0100 */
+#define ATMEL_AT45DB081D 0x25, 0x00
+#define ATMEL_AT45DB081E /* same as above but with EDI 0x01, 0x00, */
#define ATMEL_AT45DB161 /* No ID (opcode) available for AT45DB161, AT45DB161B */
-#define ATMEL_AT45DB161D 0x2600
-#define ATMEL_AT45DB161E /* same as above but with EDI 0x0100 */
+#define ATMEL_AT45DB161D 0x26, 0x00
+#define ATMEL_AT45DB161E /* same as above but with EDI 0x01, 0x00, */
#define ATMEL_AT45DB321 /* No ID (opcode) available for AT45DB321, AT45DB321B */
-#define ATMEL_AT45DB321C 0x2700
-#define ATMEL_AT45DB321E /* same as above but with EDI 0x0100 */
-#define ATMEL_AT45DB321D 0x2701 /* Buggy data sheet */
+#define ATMEL_AT45DB321C 0x27, 0x00
+#define ATMEL_AT45DB321E /* same as above but with EDI 0x01, 0x00, */
+#define ATMEL_AT45DB321D 0x27, 0x01 /* Buggy data sheet */
#define ATMEL_AT45DB642 /* No ID (opcode) available for AT45DB642 */
-#define ATMEL_AT45DB642D 0x2800
+#define ATMEL_AT45DB642D 0x28, 0x00
#define ATMEL_AT49BV512 0x03
-#define ATMEL_AT49F002N 0x07 /* for AT49F002(N) */
+#define ATMEL_AT49F002N 0x07 /* for AT49F002(N) */
#define ATMEL_AT49LH002 0xE9
-#define ATMEL_AT49F002NT 0x08 /* for AT49F002(N)T */
-#define ATMEL_AT49F010 0x17 /* Same as AT49HF010 */
+#define ATMEL_AT49F002NT 0x08 /* for AT49F002(N)T */
+#define ATMEL_AT49F010 0x17 /* Same as AT49HF010 */
#define ATMEL_AT49F020 0x0B
#define ATMEL_AT49F040 0x13
#define ATMEL_AT49F080 0x23
#define ATMEL_AT49F080T 0x27
/* Bright Microelectronics has the same manufacturer ID as Hyundai... */
-#define BRIGHT_ID 0xAD /* Bright Microelectronics */
+#define BRIGHT_ID 0xAD /* Bright Microelectronics */
#define BRIGHT_BM29F040 0x40
#define BRIGHT_BM29F400B 0xAB
#define BRIGHT_BM29F400T 0xAD
-#define CATALYST_ID 0x31 /* Catalyst */
+#define CATALYST_ID 0x31 /* Catalyst */
#define CATALYST_CAT28F512 0xB8
-#define ESMT_ID 0x8C /* Elite Semiconductor Memory Technology (ESMT) / EFST Elite Flash Storage */
-#define ESMT_F25L008A 0x2014
-#define ESMT_F25L32PA 0x2016
-#define ESMT_F25D08QA 0x2534
-#define ESMT_F25L16QA2S 0x4015
-#define ESMT_F25L32QA 0x4016
-#define ESMT_F25L32QA2S 0x4116
-#define ESMT_F25L64QA 0x4117
-#define ESMT_F25L128QA 0x4118
+#define ESMT_ID 0x8C /* Elite Semiconductor Memory Technology (ESMT) /
+ * EFST Elite Flash Storage */
+#define ESMT_F25L008A 0x20, 0x14
+#define ESMT_F25L32PA 0x20, 0x16
+#define ESMT_F25D08QA 0x25, 0x34
+#define ESMT_F25L16QA2S 0x40, 0x15
+#define ESMT_F25L32QA 0x40, 0x16
+#define ESMT_F25L32QA2S 0x41, 0x16
+#define ESMT_F25L64QA 0x41, 0x17
+#define ESMT_F25L128QA 0x41, 0x18
#define ESMT_F49B002UA 0x00
/*
- * EN25 chips are SPI, first byte of device ID is memory type,
+ * EN25 chips are SPI, first byte of device ID is memory type
* second byte of device ID is log(bitsize)-9.
* Vendor and device ID of EN29 series are both prefixed with 0x7F, which
* is the continuation code for IDs in bank 2.
@@ -226,85 +221,85 @@
* a collision with Mitsubishi. Mitsubishi once manufactured flash chips.
* Let's hope they are not manufacturing SPI flash chips as well.
*/
-#define EON_ID 0x7F1C /* EON Silicon Devices */
-#define EON_ID_NOPREFIX 0x1C /* EON, missing 0x7F prefix */
-#define EON_EN25B05 0x2010 /* Same as P05, 2^19 kbit or 2^16 kByte */
+#define EON_ID 0x7F, 0x1C /* EON Silicon Devices */
+#define EON_ID_NOPREFIX 0x1C /* EON, without prefix */
+#define EON_EN25B05 0x20, 0x10 /* Same as P05, 2^19 kbit or 2^16 kByte */
#define EON_EN25B05T 0x25
#define EON_EN25B05B 0x95
-#define EON_EN25B10 0x2011 /* Same as P10 */
+#define EON_EN25B10 0x20, 0x11 /* Same as P10 */
#define EON_EN25B10T 0x40
#define EON_EN25B10B 0x30
-#define EON_EN25B20 0x2012 /* Same as P20 */
+#define EON_EN25B20 0x20, 0x12 /* Same as P20 */
#define EON_EN25B20T 0x41
#define EON_EN25B20B 0x31
-#define EON_EN25B40 0x2013 /* Same as P40 */
+#define EON_EN25B40 0x20, 0x13 /* Same as P40 */
#define EON_EN25B40T 0x42
#define EON_EN25B40B 0x32
-#define EON_EN25B80 0x2014 /* Same as P80 */
+#define EON_EN25B80 0x20, 0x14 /* Same as P80 */
#define EON_EN25B80T 0x43
#define EON_EN25B80B 0x33
-#define EON_EN25B16 0x2015 /* Same as P16 */
+#define EON_EN25B16 0x20, 0x15 /* Same as P16 */
#define EON_EN25B16T 0x44
#define EON_EN25B16B 0x34
-#define EON_EN25B32 0x2016 /* Same as P32 */
+#define EON_EN25B32 0x20, 0x16 /* Same as P32 */
#define EON_EN25B32T 0x45
#define EON_EN25B32B 0x35
-#define EON_EN25B64 0x2017 /* Same as P64 */
+#define EON_EN25B64 0x20, 0x17 /* Same as P64 */
#define EON_EN25B64T 0x46
#define EON_EN25B64B 0x36
-#define EON_EN25F05 0x3110
-#define EON_EN25F10 0x3111
-#define EON_EN25F20 0x3112
-#define EON_EN25F40 0x3113
-#define EON_EN25F80 0x3114
-#define EON_EN25F16 0x3115
-#define EON_EN25F32 0x3116
-#define EON_EN25F64 0x3117 /* guessed */
-#define EON_EN25Q40 0x3013
-#define EON_EN25Q80 0x3014
-#define EON_EN25Q16 0x3015 /* Same as EN25D16 */
-#define EON_EN25Q32 0x3016 /* Same as EN25Q32A and EN25Q32B */
-#define EON_EN25Q64 0x3017
-#define EON_EN25Q128 0x3018
-#define EON_EN25QH16 0x7015
-#define EON_EN25QH32 0x7016
-#define EON_EN25QH64 0x7017
-#define EON_EN25QH128 0x7018
-#define EON_EN25QH256 0x7019
-#define EON_EN25S10 0x3811
-#define EON_EN25S20 0x3812
-#define EON_EN25S40 0x3813
-#define EON_EN25S80 0x3814
-#define EON_EN25S16 0x3815
-#define EON_EN25S32 0x3816
-#define EON_EN25S64 0x3817
-#define EON_EN25T80 0x5114
-#define EON_EN25T16 0x5115
-#define EON_EN29F512 0x7F21
+#define EON_EN25F05 0x31, 0x10
+#define EON_EN25F10 0x31, 0x11
+#define EON_EN25F20 0x31, 0x12
+#define EON_EN25F40 0x31, 0x13
+#define EON_EN25F80 0x31, 0x14
+#define EON_EN25F16 0x31, 0x15
+#define EON_EN25F32 0x31, 0x16
+#define EON_EN25F64 0x31, 0x17 /* guessed */
+#define EON_EN25Q40 0x30, 0x13
+#define EON_EN25Q80 0x30, 0x14
+#define EON_EN25Q16 0x30, 0x15 /* Same as EN25D16 */
+#define EON_EN25Q32 0x30, 0x16 /* Same as EN25Q32A and EN25Q32B */
+#define EON_EN25Q64 0x30, 0x17
+#define EON_EN25Q128 0x30, 0x18
+#define EON_EN25QH16 0x70, 0x15
+#define EON_EN25QH32 0x70, 0x16
+#define EON_EN25QH64 0x70, 0x17
+#define EON_EN25QH128 0x70, 0x18
+#define EON_EN25QH256 0x70, 0x19
+#define EON_EN25S10 0x38, 0x11
+#define EON_EN25S20 0x38, 0x12
+#define EON_EN25S40 0x38, 0x13
+#define EON_EN25S80 0x38, 0x14
+#define EON_EN25S16 0x38, 0x15
+#define EON_EN25S32 0x38, 0x16
+#define EON_EN25S64 0x38, 0x17
+#define EON_EN25T80 0x51, 0x14
+#define EON_EN25T16 0x51, 0x15
+#define EON_EN29F512 0x7F, 0x21
#define EON_EN29F010 0x20
-#define EON_EN29F040A 0x7F04
-#define EON_EN29LV010 0x7F6E
-#define EON_EN29LV040A 0x7F4F /* EN29LV040(A) */
+#define EON_EN29F040A 0x7F, 0x04
+#define EON_EN29LV010 0x7F, 0x6E
+#define EON_EN29LV040A 0x7F, 0x4F /* EN29LV040(A) */
#define EON_EN29LV640B 0xCB
-#define EON_EN29F002T 0x7F92 /* Same as EN29F002A */
-#define EON_EN29F002B 0x7F97 /* Same as EN29F002AN */
-
-#define EXCEL_ID 0x7F7F7F7F4A /* Excel Semiconductor Inc. (ESI) resides in bank 5 */
-#define EXCEL_ID_NOPREFIX 0x4A /* ESI, missing 0x7F prefix */
-#define EXCEL_ES25P40 0x2013
-#define EXCEL_ES25P80 0x2014
-#define EXCEL_ES25P16 0x2015
-
-#define FIDELIX_ID 0xF8 /* Fidelix */
-#define FIDELIX_FM25M16 0x4215
-#define FIDELIX_FM25M32 0x4216
-#define FIDELIX_FM25M64 0x4217
-#define FIDELIX_FM25Q08 0x3214
-#define FIDELIX_FM25Q16 0x3215 /* Same as FM25S16 (which is apparently single I/O only) */
-#define FIDELIX_FM25Q32 0x3216
-#define FIDELIX_FM25Q64 0x3217
-
-#define FUJITSU_ID 0x04 /* Fujitsu */
+#define EON_EN29F002T 0x7F, 0x92 /* Same as EN29F002A */
+#define EON_EN29F002B 0x7F, 0x97 /* Same as EN29F002AN */
+
+#define EXCEL_ID 0x7F, 0x7F, 0x7F, 0x7F, 0x4A /* Excel Semiconductor Inc. (ESI), in bank 5 */
+#define EXCEL_ID_NOPREFIX 0x4A /* ESI, without prefix */
+#define EXCEL_ES25P40 0x20, 0x13
+#define EXCEL_ES25P80 0x20, 0x14
+#define EXCEL_ES25P16 0x20, 0x15
+
+#define FIDELIX_ID 0xF8 /* Fidelix */
+#define FIDELIX_FM25M16 0x42, 0x15
+#define FIDELIX_FM25M32 0x42, 0x16
+#define FIDELIX_FM25M64 0x42, 0x17
+#define FIDELIX_FM25Q08 0x32, 0x14
+#define FIDELIX_FM25Q16 0x32, 0x15 /* Same as FM25S16 (which is apparently single I/O only) */
+#define FIDELIX_FM25Q32 0x32, 0x16
+#define FIDELIX_FM25Q64 0x32, 0x17
+
+#define FUJITSU_ID 0x04 /* Fujitsu */
#define FUJITSU_MBM29DL400BC 0x0F
#define FUJITSU_MBM29DL400TC 0x0C
#define FUJITSU_MBM29DL800BA 0xCB
@@ -332,173 +327,173 @@
#define FUJITSU_MBM29LV200TC 0x3B
#define FUJITSU_MBM29LV400BC 0xBA
#define FUJITSU_MBM29LV400TC 0xB9
-#define FUJITSU_MBM29LV800BA 0x5B /* Same as MBM29LV800BE */
-#define FUJITSU_MBM29LV800TA 0xDA /* Same as MBM29LV800TE */
-#define FUJITSU_MBM29LV160BE 0x49 /* 16 b mode 0x2249 */
-#define FUJITSU_MBM29LV160TE 0xC4 /* 16 b mode 0x22C4 */
-
-#define GIGADEVICE_ID 0xC8 /* GigaDevice */
-#define GIGADEVICE_GD25T80 0x3114
-#define GIGADEVICE_GD25Q512 0x4010
-#define GIGADEVICE_GD25Q10 0x4011
-#define GIGADEVICE_GD25Q20 0x4012 /* Same as GD25QB */
-#define GIGADEVICE_GD25Q40 0x4013 /* Same as GD25QB */
-#define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */
-#define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */
-#define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */
-#define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */
-#define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B only? */
-#define GIGADEVICE_GD25LQ40 0x6013
-#define GIGADEVICE_GD25LQ80 0x6014
-#define GIGADEVICE_GD25LQ16 0x6015
-#define GIGADEVICE_GD25LQ32 0x6016
-#define GIGADEVICE_GD25LQ64 0x6017 /* Same as GD25LQ64B (which is faster) */
-#define GIGADEVICE_GD25LQ128 0x6018
-
-#define HYUNDAI_ID 0xAD /* Hyundai */
-#define HYUNDAI_HY29F400T 0x23 /* Same as HY29F400AT */
-#define HYUNDAI_HY29F800B 0x58 /* Same as HY29F800AB */
+#define FUJITSU_MBM29LV800BA 0x5B /* Same as MBM29LV800BE */
+#define FUJITSU_MBM29LV800TA 0xDA /* Same as MBM29LV800TE */
+#define FUJITSU_MBM29LV160BE 0x49 /* 16 b mode 0x22, 0x49, */
+#define FUJITSU_MBM29LV160TE 0xC4 /* 16 b mode 0x22, 0xC4, */
+
+#define GIGADEVICE_ID 0xC8 /* GigaDevice */
+#define GIGADEVICE_GD25T80 0x31, 0x14
+#define GIGADEVICE_GD25Q512 0x40, 0x10
+#define GIGADEVICE_GD25Q10 0x40, 0x11
+#define GIGADEVICE_GD25Q20 0x40, 0x12 /* Same as GD25QB */
+#define GIGADEVICE_GD25Q40 0x40, 0x13 /* Same as GD25QB */
+#define GIGADEVICE_GD25Q80 0x40, 0x14 /* Same as GD25Q80B (which has OTP) */
+#define GIGADEVICE_GD25Q16 0x40, 0x15 /* Same as GD25Q16B (which has OTP) */
+#define GIGADEVICE_GD25Q32 0x40, 0x16 /* Same as GD25Q32B */
+#define GIGADEVICE_GD25Q64 0x40, 0x17 /* Same as GD25Q64B */
+#define GIGADEVICE_GD25Q128 0x40, 0x18 /* GD25Q128B only? */
+#define GIGADEVICE_GD25LQ40 0x60, 0x13
+#define GIGADEVICE_GD25LQ80 0x60, 0x14
+#define GIGADEVICE_GD25LQ16 0x60, 0x15
+#define GIGADEVICE_GD25LQ32 0x60, 0x16
+#define GIGADEVICE_GD25LQ64 0x60, 0x17 /* Same as GD25LQ64B (which is faster) */
+#define GIGADEVICE_GD25LQ128 0x60, 0x18
+
+#define HYUNDAI_ID 0xAD /* Hyundai */
+#define HYUNDAI_HY29F400T 0x23 /* Same as HY29F400AT */
+#define HYUNDAI_HY29F800B 0x58 /* Same as HY29F800AB */
#define HYUNDAI_HY29LV800B 0x5B
#define HYUNDAI_HY29F040A 0xA4
-#define HYUNDAI_HY29F400B 0xAB /* Same as HY29F400AB */
+#define HYUNDAI_HY29F400B 0xAB /* Same as HY29F400AB */
#define HYUNDAI_HY29F002B 0x34
#define HYUNDAI_HY29F002T 0xB0
#define HYUNDAI_HY29LV400T 0xB9
#define HYUNDAI_HY29LV400B 0xBA
#define HYUNDAI_HY29F080 0xD5
-#define HYUNDAI_HY29F800T 0xD6 /* Same as HY29F800AT */
+#define HYUNDAI_HY29F800T 0xD6 /* Same as HY29F800AT */
#define HYUNDAI_HY29LV800T 0xDA
-#define IMT_ID 0x7F1F /* Integrated Memory Technologies */
+#define IMT_ID 0x7F, 0x1F /* Integrated Memory Technologies */
#define IMT_IM29F004B 0xAE
#define IMT_IM29F004T 0xAF
-#define INTEL_ID 0x89 /* Intel */
+#define INTEL_ID 0x89 /* Intel */
#define INTEL_28F320J5 0x14
#define INTEL_28F640J5 0x15
#define INTEL_28F320J3 0x16
#define INTEL_28F640J3 0x17
#define INTEL_28F128J3 0x18
#define INTEL_28F256J3 0x1D
-#define INTEL_28F400T 0x70 /* 28F400BV/BX/CE/CV-T */
-#define INTEL_28F400B 0x71 /* 28F400BV/BX/CE/CV-B */
-#define INTEL_28F200T 0x74 /* 28F200BL/BV/BX/CV-T */
-#define INTEL_28F200B 0x75 /* 28F200BL/BV/BX/CV-B */
-#define INTEL_28F004T 0x78 /* 28F004B5/BE/BV/BX-T */
-#define INTEL_28F004B 0x79 /* 28F004B5/BE/BV/BX-B */
-#define INTEL_28F002T 0x7C /* 28F002BC/BL/BV/BX-T */
-#define INTEL_28F002B 0x7D /* 28F002BL/BV/BX-B */
-#define INTEL_28F001T 0x94 /* 28F001BN/BX-T */
-#define INTEL_28F001B 0x95 /* 28F001BN/BX-B */
-#define INTEL_28F008T 0x98 /* 28F008BE/BV-T */
-#define INTEL_28F008B 0x99 /* 28F008BE/BV-B */
-#define INTEL_28F800T 0x9C /* 28F800B5/BV/CE/CV-T */
-#define INTEL_28F800B 0x9D /* 28F800B5/BV/CE/CV-B */
-#define INTEL_28F016SV 0xA0 /* 28F016SA/SV */
+#define INTEL_28F400T 0x70 /* 28F400BV/BX/CE/CV-T */
+#define INTEL_28F400B 0x71 /* 28F400BV/BX/CE/CV-B */
+#define INTEL_28F200T 0x74 /* 28F200BL/BV/BX/CV-T */
+#define INTEL_28F200B 0x75 /* 28F200BL/BV/BX/CV-B */
+#define INTEL_28F004T 0x78 /* 28F004B5/BE/BV/BX-T */
+#define INTEL_28F004B 0x79 /* 28F004B5/BE/BV/BX-B */
+#define INTEL_28F002T 0x7C /* 28F002BC/BL/BV/BX-T */
+#define INTEL_28F002B 0x7D /* 28F002BL/BV/BX-B */
+#define INTEL_28F001T 0x94 /* 28F001BN/BX-T */
+#define INTEL_28F001B 0x95 /* 28F001BN/BX-B */
+#define INTEL_28F008T 0x98 /* 28F008BE/BV-T */
+#define INTEL_28F008B 0x99 /* 28F008BE/BV-B */
+#define INTEL_28F800T 0x9C /* 28F800B5/BV/CE/CV-T */
+#define INTEL_28F800B 0x9D /* 28F800B5/BV/CE/CV-B */
+#define INTEL_28F016SV 0xA0 /* 28F016SA/SV */
#define INTEL_28F008SA 0xA2
-#define INTEL_28F008S3 0xA6 /* 28F008S3/S5/SC */
-#define INTEL_28F004S3 0xA7 /* 28F008S3/S5/SC */
+#define INTEL_28F008S3 0xA6 /* 28F008S3/S5/SC */
+#define INTEL_28F004S3 0xA7 /* 28F008S3/S5/SC */
#define INTEL_28F016XS 0xA8
-#define INTEL_28F016S3 0xAA /* 28F016S3/S5/SC */
+#define INTEL_28F016S3 0xAA /* 28F016S3/S5/SC */
#define INTEL_82802AC 0xAC
#define INTEL_82802AB 0xAD
#define INTEL_28F010 0xB4
#define INTEL_28F512 0xB8
#define INTEL_28F256A 0xB9
#define INTEL_28F020 0xBD
-#define INTEL_28F016B3T 0xD0 /* 28F016B3-T */
-#define INTEL_28F016B3B 0xD1 /* 28F016B3-B */
-#define INTEL_28F008B3T 0xD2 /* 28F008B3-T */
-#define INTEL_28F008B3B 0xD3 /* 28F008B3-B */
-#define INTEL_28F004B3T 0xD4 /* 28F004B3-T */
-#define INTEL_28F004B3B 0xD5 /* 28F004B3-B */
-#define INTEL_25F160S33B8 0x8911 /* Same as 25F016S33B8 */
-#define INTEL_25F320S33B8 0x8912
-#define INTEL_25F640S33B8 0x8913
-#define INTEL_25F160S33T8 0x8915 /* Same as 25F016S33T8 */
-#define INTEL_25F320S33T8 0x8916
-#define INTEL_25F640S33T8 0x8917
-
-#define SHARP_LH28F008SA 0xA2 /* Sharp chip, Intel Vendor ID */
-#define SHARP_LH28F008SC 0xA6 /* Sharp chip, Intel Vendor ID */
-
-#define ISSI_ID 0xD5 /* ISSI Integrated Silicon Solutions */
-
-#define MACRONIX_ID 0xC2 /* Macronix (MX) */
+#define INTEL_28F016B3T 0xD0 /* 28F016B3-T */
+#define INTEL_28F016B3B 0xD1 /* 28F016B3-B */
+#define INTEL_28F008B3T 0xD2 /* 28F008B3-T */
+#define INTEL_28F008B3B 0xD3 /* 28F008B3-B */
+#define INTEL_28F004B3T 0xD4 /* 28F004B3-T */
+#define INTEL_28F004B3B 0xD5 /* 28F004B3-B */
+#define INTEL_25F160S33B8 0x89, 0x11 /* Same as 25F016S33B8 */
+#define INTEL_25F320S33B8 0x89, 0x12
+#define INTEL_25F640S33B8 0x89, 0x13
+#define INTEL_25F160S33T8 0x89, 0x15 /* Same as 25F016S33T8 */
+#define INTEL_25F320S33T8 0x89, 0x16
+#define INTEL_25F640S33T8 0x89, 0x17
+
+#define SHARP_LH28F008SA 0xA2 /* Sharp chip, Intel Vendor ID */
+#define SHARP_LH28F008SC 0xA6 /* Sharp chip, Intel Vendor ID */
+
+#define ISSI_ID 0xD5 /* ISSI Integrated Silicon Solutions */
+
+#define MACRONIX_ID 0xC2 /* Macronix (MX) */
/* Mask ROMs */
-#define MACRONIX_MX23L3254 0x0516
-/* MX25 chips are SPI, first byte of device ID is memory type,
+#define MACRONIX_MX23L3254 0x05, 0x16
+/* MX25 chips are SPI, first byte of device ID is memory type
* second byte of device ID is log(bitsize)-9.
* Generalplus SPI chips seem to be compatible with Macronix
* and use the same set of IDs. */
-#define MACRONIX_MX25L512 0x2010 /* Same as MX25L512E, MX25V512, MX25V512C */
-#define MACRONIX_MX25L1005 0x2011 /* Same as MX25L1005C, MX25L1006E */
-#define MACRONIX_MX25L2005 0x2012 /* Same as MX25L2005C */
-#define MACRONIX_MX25L4005 0x2013 /* Same as MX25L4005A, MX25L4005C */
-#define MACRONIX_MX25L8005 0x2014 /* Same as MX25V8005; FIXME: MX25L8073E (4k 0x20) */
-#define MACRONIX_MX25L1605 0x2015 /* MX25L1605 (64k 0x20); MX25L1605A/MX25L1606E (4k 0x20, 64k 0x52); MX25L1605D/MX25L1608D/MX25L1673E (4k 0x20) */
-#define MACRONIX_MX25L3205 0x2016 /* MX25L3205, MX25L3205A (64k 0x20); MX25L3205D/MX25L3208D (4k 0x20); MX25L3206E (4k 0x20, 64k 0x52); MX25L3273E (4k 0x20, 32k 0x52) */
-#define MACRONIX_MX25L6405 0x2017 /* MX25L6405, MX25L6405D (64k 0x20); MX25L6406E/MX25L6436E (4k 0x20); MX25L6445E/MX25L6473E (4k 0x20, 32k 0x52) */
-#define MACRONIX_MX25L12805 0x2018 /* Same as MX25L12805D, MX25L12835F, MX25L12845E (the latter two support completely new ID commands) */
-#define MACRONIX_MX25L25635F 0x2019 /* Same as MX25L25639F, but the latter seems to not support REMS */
-#define MACRONIX_MX25L1635D 0x2415
-#define MACRONIX_MX25L1635E 0x2515 /* MX25L1635{E} */
-#define MACRONIX_MX25U1635E 0x2535
-#define MACRONIX_MX25U3235E 0x2536 /* Same as MX25U6435F */
-#define MACRONIX_MX25U6435E 0x2537 /* Same as MX25U6435F */
-#define MACRONIX_MX25U12835E 0x2538 /* Same as MX25U12835F */
-#define MACRONIX_MX25U25635F 0x2539
-#define MACRONIX_MX25L3235D 0x5E16 /* MX25L3225D/MX25L3235D/MX25L3237D */
+#define MACRONIX_MX25L512 0x20, 0x10 /* Same as MX25L512E, MX25V512, MX25V512C */
+#define MACRONIX_MX25L1005 0x20, 0x11 /* Same as MX25L1005C, MX25L1006E */
+#define MACRONIX_MX25L2005 0x20, 0x12 /* Same as MX25L2005C */
+#define MACRONIX_MX25L4005 0x20, 0x13 /* Same as MX25L4005A, MX25L4005C */
+#define MACRONIX_MX25L8005 0x20, 0x14 /* Same as MX25V8005; FIXME: MX25L8073E (4k 0x20) */
+#define MACRONIX_MX25L1605 0x20, 0x15 /* MX25L1605 (64k 0x20); MX25L1605A/MX25L1606E (4k 0x20, 64k 0x52); MX25L1605D/MX25L1608D/MX25L1673E (4k 0x20) */
+#define MACRONIX_MX25L3205 0x20, 0x16 /* MX25L3205, MX25L3205A (64k 0x20); MX25L3205D/MX25L3208D (4k 0x20); MX25L3206E (4k 0x20, 64k 0x52); MX25L3273E (4k 0x20, 32k 0x52) */
+#define MACRONIX_MX25L6405 0x20, 0x17 /* MX25L6405, MX25L6405D (64k 0x20); MX25L6406E/MX25L6436E (4k 0x20); MX25L6445E/MX25L6473E (4k 0x20, 32k 0x52) */
+#define MACRONIX_MX25L12805 0x20, 0x18 /* Same as MX25L12805D, MX25L12835F, MX25L12845E (the latter two support completely new ID commands) */
+#define MACRONIX_MX25L25635F 0x20, 0x19 /* Same as MX25L25639F, but the latter seems to not support REMS */
+#define MACRONIX_MX25L1635D 0x24, 0x15
+#define MACRONIX_MX25L1635E 0x25, 0x15 /* MX25L1635{E} */
+#define MACRONIX_MX25U1635E 0x25, 0x35
+#define MACRONIX_MX25U3235E 0x25, 0x36 /* Same as MX25U6435F */
+#define MACRONIX_MX25U6435E 0x25, 0x37 /* Same as MX25U6435F */
+#define MACRONIX_MX25U12835E 0x25, 0x38 /* Same as MX25U12835F */
+#define MACRONIX_MX25U25635F 0x25, 0x39
+#define MACRONIX_MX25L3235D 0x5E, 0x16 /* MX25L3225D/MX25L3235D/MX25L3237D */
#define MACRONIX_MX29F001B 0x19
#define MACRONIX_MX29F001T 0x18
-#define MACRONIX_MX29F002B 0x34 /* Same as MX29F002NB; N has reset pin n/c. */
-#define MACRONIX_MX29F002T 0xB0 /* Same as MX29F002NT; N has reset pin n/c. */
+#define MACRONIX_MX29F002B 0x34 /* Same as MX29F002NB; N has reset pin n/c. */
+#define MACRONIX_MX29F002T 0xB0 /* Same as MX29F002NT; N has reset pin n/c. */
#define MACRONIX_MX29F004B 0x46
#define MACRONIX_MX29F004T 0x45
-#define MACRONIX_MX29F022T 0x36 /* Same as MX29F022NT */
-#define MACRONIX_MX29F040 0xA4 /* Same as MX29F040C */
+#define MACRONIX_MX29F022T 0x36 /* Same as MX29F022NT */
+#define MACRONIX_MX29F040 0xA4 /* Same as MX29F040C */
#define MACRONIX_MX29F080 0xD5
-#define MACRONIX_MX29F200B 0x57 /* Same as MX29F200CB */
-#define MACRONIX_MX29F200T 0x51 /* Same as MX29F200CT */
-#define MACRONIX_MX29F400B 0xAB /* Same as MX29F400CB */
-#define MACRONIX_MX29F400T 0x23 /* Same as MX29F400CT */
+#define MACRONIX_MX29F200B 0x57 /* Same as MX29F200CB */
+#define MACRONIX_MX29F200T 0x51 /* Same as MX29F200CT */
+#define MACRONIX_MX29F400B 0xAB /* Same as MX29F400CB */
+#define MACRONIX_MX29F400T 0x23 /* Same as MX29F400CT */
#define MACRONIX_MX29F800B 0x58
#define MACRONIX_MX29F800T 0xD6
#define MACRONIX_MX29LV002CB 0x5A
#define MACRONIX_MX29LV002CT 0x59
-#define MACRONIX_MX29LV004B 0xB6 /* Same as MX29LV004CB */
-#define MACRONIX_MX29LV004T 0xB5 /* Same as MX29LV004CT */
-#define MACRONIX_MX29LV008B 0x37 /* Same as MX29LV008CB */
-#define MACRONIX_MX29LV008T 0x3E /* Same as MX29LV008CT */
-#define MACRONIX_MX29LV040 0x4F /* Same as MX29LV040C */
+#define MACRONIX_MX29LV004B 0xB6 /* Same as MX29LV004CB */
+#define MACRONIX_MX29LV004T 0xB5 /* Same as MX29LV004CT */
+#define MACRONIX_MX29LV008B 0x37 /* Same as MX29LV008CB */
+#define MACRONIX_MX29LV008T 0x3E /* Same as MX29LV008CT */
+#define MACRONIX_MX29LV040 0x4F /* Same as MX29LV040C */
#define MACRONIX_MX29LV081 0x38
#define MACRONIX_MX29LV128DB 0x7A
#define MACRONIX_MX29LV128DT 0x7E
-#define MACRONIX_MX29LV160DB 0x49 /* Same as MX29LV161DB/MX29LV160CB */
-#define MACRONIX_MX29LV160DT 0xC4 /* Same as MX29LV161DT/MX29LV160CT */
-#define MACRONIX_MX29LV320DB 0xA8 /* Same as MX29LV321DB */
-#define MACRONIX_MX29LV320DT 0xA7 /* Same as MX29LV321DT */
-#define MACRONIX_MX29LV400B 0xBA /* Same as MX29LV400CB */
-#define MACRONIX_MX29LV400T 0xB9 /* Same as MX29LV400CT */
-#define MACRONIX_MX29LV640DB 0xCB /* Same as MX29LV640EB */
-#define MACRONIX_MX29LV640DT 0xC9 /* Same as MX29LV640ET */
-#define MACRONIX_MX29LV800B 0x5B /* Same as MX29LV800CB */
-#define MACRONIX_MX29LV800T 0xDA /* Same as MX29LV800CT */
+#define MACRONIX_MX29LV160DB 0x49 /* Same as MX29LV161DB/MX29LV160CB */
+#define MACRONIX_MX29LV160DT 0xC4 /* Same as MX29LV161DT/MX29LV160CT */
+#define MACRONIX_MX29LV320DB 0xA8 /* Same as MX29LV321DB */
+#define MACRONIX_MX29LV320DT 0xA7 /* Same as MX29LV321DT */
+#define MACRONIX_MX29LV400B 0xBA /* Same as MX29LV400CB */
+#define MACRONIX_MX29LV400T 0xB9 /* Same as MX29LV400CT */
+#define MACRONIX_MX29LV640DB 0xCB /* Same as MX29LV640EB */
+#define MACRONIX_MX29LV640DT 0xC9 /* Same as MX29LV640ET */
+#define MACRONIX_MX29LV800B 0x5B /* Same as MX29LV800CB */
+#define MACRONIX_MX29LV800T 0xDA /* Same as MX29LV800CT */
#define MACRONIX_MX29SL402CB 0xF1
#define MACRONIX_MX29SL402CT 0x70
-#define MACRONIX_MX29SL800CB 0x6B /* Same as MX29SL802CB */
-#define MACRONIX_MX29SL800CT 0xEA /* Same as MX29SL802CT */
+#define MACRONIX_MX29SL800CB 0x6B /* Same as MX29SL802CB */
+#define MACRONIX_MX29SL800CT 0xEA /* Same as MX29SL802CT */
/* Nantronics Semiconductors is listed in JEP106AJ in bank 7, so it should have 6 continuation codes in front
* of the manufacturer ID of 0xD5. http://www.nantronicssemi.com */
-#define NANTRONICS_ID 0x7F7F7F7F7F7FD5 /* Nantronics */
-#define NANTRONICS_ID_NOPREFIX 0xD5 /* Nantronics, missing prefix */
-#define NANTRONICS_N25S10 0x3011
-#define NANTRONICS_N25S20 0x3012
-#define NANTRONICS_N25S40 0x3013
-#define NANTRONICS_N25S80 0x3014
-#define NANTRONICS_N25S16 0x3015
+#define NANTRONICS_ID 0x7F, 0x7F, 0x7F, 0x7F, 0x7F, 0x7F, 0xD5 /* Nantronics */
+#define NANTRONICS_ID_NOPREFIX 0xD5 /* Nantronics, missing prefix */
+#define NANTRONICS_N25S10 0x30, 0x11
+#define NANTRONICS_N25S20 0x30, 0x12
+#define NANTRONICS_N25S40 0x30, 0x13
+#define NANTRONICS_N25S80 0x30, 0x14
+#define NANTRONICS_N25S16 0x30, 0x15
/*
* Programmable Micro Corp is listed in JEP106W in bank 2, so it should
@@ -506,102 +501,102 @@
* Apparently this name is owned by "Chingis Technology Corporation" http://www.chingistek.com which is now a
* subsidiary of ISSI. They continue to use the PMC manufacturer ID nevertheless.
*/
-#define PMC_ID 0x7F9D /* PMC */
-#define PMC_ID_NOPREFIX 0x9D /* PMC, missing 0x7F prefix */
+#define PMC_ID 0x7F, 0x9D /* PMC */
+#define PMC_ID_NOPREFIX 0x9D /* PMC, missing 0x7F prefix */
#define PMC_PM25LD256C 0x2F
-#define PMC_PM25LD512 0x20 /* Same as Pm25LD512C, but the latter has more locking options. */
-#define PMC_PM25LD010 0x21 /* Same as Pm25LD010C, but the latter has more locking options. */
-#define PMC_PM25LD020 0x22 /* Same as Pm25LD020C, but the latter has more locking options. */
-#define PMC_PM25LV512 0x7B /* Same as Pm25LV512A */
-#define PMC_PM25LV010 0x7C /* Same as Pm25LV010A, but the former does not support RDID but RES3 only. */
+#define PMC_PM25LD512 0x20 /* Same as Pm25LD512C, but the latter has more locking options. */
+#define PMC_PM25LD010 0x21 /* Same as Pm25LD010C, but the latter has more locking options. */
+#define PMC_PM25LD020 0x22 /* Same as Pm25LD020C, but the latter has more locking options. */
+#define PMC_PM25LV512 0x7B /* Same as Pm25LV512A */
+#define PMC_PM25LV010 0x7C /* Same as Pm25LV010A, but the former does not support RDID but RES3 only. */
#define PMC_PM25LV020 0x7D
-#define PMC_PM25LV040 0x7E /* Same as PM25LD040(C), but the latter supports more features. */
+#define PMC_PM25LV040 0x7E /* Same as PM25LD040(C), but the latter supports more features. */
#define PMC_PM25LV080B 0x13
#define PMC_PM25LV016B 0x14
#define PMC_PM29F002T 0x1D
#define PMC_PM29F002B 0x2D
-#define PMC_PM39LV512 0x1B /* Same as IS39LV512 */
-#define PMC_PM39F010 0x1C /* Same as Pm39LV010, IS39LV010 */
+#define PMC_PM39LV512 0x1B /* Same as IS39LV512 */
+#define PMC_PM39F010 0x1C /* Same as Pm39LV010, IS39LV010 */
#define PMC_PM39LV020 0x3D
-#define PMC_PM39LV040 0x3E /* Same as IS39LV040 */
+#define PMC_PM39LV040 0x3E /* Same as IS39LV040 */
#define PMC_PM39F020 0x4D
#define PMC_PM39F040 0x4E
#define PMC_PM49FL002 0x6D
#define PMC_PM49FL004 0x6E
/*
- * The Sanyo chip found so far uses SPI, first byte is manufacture code,
- * second byte is the device code,
+ * The Sanyo chip found so far uses SPI, first byte is manufacture code
+ * second byte is the device code
* third byte is a dummy byte.
*/
-#define SANYO_ID 0x62 /* Sanyo */
-#define SANYO_LE25FW203A 0x1600
-#define SANYO_LE25FW403A 0x1100
+#define SANYO_ID 0x62 /* Sanyo */
+#define SANYO_LE25FW203A 0x16, 0x00
+#define SANYO_LE25FW403A 0x11, 0x00
#define SANYO_LE25FW106 0x15
-#define SANYO_LE25FW406 0x07 /* RES2 */
-#define SANYO_LE25FW418A 0x10 /* RES2 and some weird 1 byte RDID variant */
-#define SANYO_LE25FW406A 0x1A /* RES2, no datasheet */
-#define SANYO_LE25FU406B 0x1E /* LE25FW418A without HD_READ mode option variant */
-#define SANYO_LE25FW806 0x26 /* RES2 and some weird 1 byte RDID variant */
-#define SANYO_LE25FW808 0x20 /* RES2 and some weird 1 byte RDID variant */
-
-#define SHARP_ID 0xB0 /* Sharp */
+#define SANYO_LE25FW406 0x07 /* RES2 */
+#define SANYO_LE25FW418A 0x10 /* RES2 and some weird 1 byte RDID variant */
+#define SANYO_LE25FW406A 0x1A /* RES2, no datasheet */
+#define SANYO_LE25FU406B 0x1E /* LE25FW418A without HD_READ mode option variant */
+#define SANYO_LE25FW806 0x26 /* RES2 and some weird 1 byte RDID variant */
+#define SANYO_LE25FW808 0x20 /* RES2 and some weird 1 byte RDID variant */
+
+#define SHARP_ID 0xB0 /* Sharp */
#define SHARP_LH28F008BJ__PT 0xEC
#define SHARP_LH28F008BJ__PB 0xED
#define SHARP_LH28F800BV__BTL 0x4B
#define SHARP_LH28F800BV__BV 0x4D
#define SHARP_LH28F800BV__TV 0x4C
-#define SHARP_LHF00L02 0xC9 /* Same as LHF00L06/LHF00L07 */
-#define SHARP_LHF00L04 0xCF /* Same as LHF00L03/LHF00L05 */
+#define SHARP_LHF00L02 0xC9 /* Same as LHF00L06/LHF00L07 */
+#define SHARP_LHF00L04 0xCF /* Same as LHF00L03/LHF00L05 */
/*
* Spansion was previously a joint venture of AMD and Fujitsu.
* S25 chips are SPI. The first device ID byte is memory type and
* the second device ID byte is memory capacity.
*/
-#define SPANSION_ID 0x01 /* Spansion, same ID as AMD */
-#define SPANSION_S25FL004A 0x0212
-#define SPANSION_S25FL008A 0x0213
-#define SPANSION_S25FL016A 0x0214
-#define SPANSION_S25FL032A 0x0215 /* Same as S25FL032P, but the latter supports EDI and CFI */
-#define SPANSION_S25FL064A 0x0216 /* Same as S25FL064P, but the latter supports EDI and CFI */
-#define SPANSION_S25FL128 0x2018
-#define SPANSION_S25FL256 0x0219
-#define SPANSION_S25FL512 0x0220
-#define SPANSION_S25FL204 0x4013
-#define SPANSION_S25FL208 0x4014
-#define SPANSION_S25FL216 0x4015 /* Same as S25FL216K, but the latter supports OTP, 3 status regs, quad I/O, SFDP etc. */
-#define SPANSION_S25FL132K 0x4016
-#define SPANSION_S25FL164K 0x4017
+#define SPANSION_ID 0x01 /* Spansion, same ID as AMD */
+#define SPANSION_S25FL004A 0x02, 0x12
+#define SPANSION_S25FL008A 0x02, 0x13
+#define SPANSION_S25FL016A 0x02, 0x14
+#define SPANSION_S25FL032A 0x02, 0x15 /* Same as S25FL032P, but the latter supports EDI and CFI */
+#define SPANSION_S25FL064A 0x02, 0x16 /* Same as S25FL064P, but the latter supports EDI and CFI */
+#define SPANSION_S25FL128 0x20, 0x18
+#define SPANSION_S25FL256 0x02, 0x19
+#define SPANSION_S25FL512 0x02, 0x20
+#define SPANSION_S25FL204 0x40, 0x13
+#define SPANSION_S25FL208 0x40, 0x14
+#define SPANSION_S25FL216 0x40, 0x15 /* Same as S25FL216K, but the latter supports OTP, 3 status regs, quad I/O, SFDP etc. */
+#define SPANSION_S25FL132K 0x40, 0x16
+#define SPANSION_S25FL164K 0x40, 0x17
/*
* SST25 chips are SPI, first byte of device ID is memory type, second
* byte of device ID is related to log(bitsize) at least for some chips.
*/
-#define SST_ID 0xBF /* SST */
-#define SST_SST25LF020_REMS 0x43 /* REMS or RES opcode */
-#define SST_SST25WF512 0x2501
-#define SST_SST25WF010 0x2502
-#define SST_SST25WF020 0x2503
-#define SST_SST25WF040 0x2504
-#define SST_SST25WF080 0x2505
-#define SST_SST25VF512A_REMS 0x48 /* REMS or RES opcode */
-#define SST_SST25VF010_REMS 0x49 /* REMS or RES opcode */
-#define SST_SST25VF020_REMS 0x43 /* REMS or RES opcode, same as SST25LF020A */
-#define SST_SST25VF020B 0x258C
-#define SST_SST25VF040_REMS 0x44 /* REMS or RES opcode, same as SST25LF040A */
-#define SST_SST25VF040B 0x258D
-#define SST_SST25VF040B_REMS 0x8D /* REMS or RES opcode */
-#define SST_SST25VF080_REMS 0x80 /* REMS or RES opcode, same as SST25LF080A */
-#define SST_SST25VF080B 0x258E
-#define SST_SST25VF080B_REMS 0x8E /* REMS or RES opcode */
-#define SST_SST25VF016B 0x2541
-#define SST_SST25VF032B 0x254A
-#define SST_SST25VF032B_REMS 0x4A /* REMS or RES opcode */
-#define SST_SST25VF064C 0x254B
-#define SST_SST26VF016 0x2601
-#define SST_SST26VF032 0x2602
-#define SST_SST26VF064B 0x2643
+#define SST_ID 0xBF /* SST */
+#define SST_SST25LF020_REMS 0x43 /* REMS or RES opcode */
+#define SST_SST25WF512 0x25, 0x01
+#define SST_SST25WF010 0x25, 0x02
+#define SST_SST25WF020 0x25, 0x03
+#define SST_SST25WF040 0x25, 0x04
+#define SST_SST25WF080 0x25, 0x05
+#define SST_SST25VF512A_REMS 0x48 /* REMS or RES opcode */
+#define SST_SST25VF010_REMS 0x49 /* REMS or RES opcode */
+#define SST_SST25VF020_REMS 0x43 /* REMS or RES opcode, same as SST25LF020A */
+#define SST_SST25VF020B 0x25, 0x8C
+#define SST_SST25VF040_REMS 0x44 /* REMS or RES opcode, same as SST25LF040A */
+#define SST_SST25VF040B 0x25, 0x8D
+#define SST_SST25VF040B_REMS 0x8D /* REMS or RES opcode */
+#define SST_SST25VF080_REMS 0x80 /* REMS or RES opcode, same as SST25LF080A */
+#define SST_SST25VF080B 0x25, 0x8E
+#define SST_SST25VF080B_REMS 0x8E /* REMS or RES opcode */
+#define SST_SST25VF016B 0x25, 0x41
+#define SST_SST25VF032B 0x25, 0x4A
+#define SST_SST25VF032B_REMS 0x4A /* REMS or RES opcode */
+#define SST_SST25VF064C 0x25, 0x4B
+#define SST_SST26VF016 0x26, 0x01
+#define SST_SST26VF032 0x26, 0x02
+#define SST_SST26VF064B 0x26, 0x43
#define SST_SST27SF512 0xA4
#define SST_SST27SF010 0xA5
#define SST_SST27SF020 0xA6
@@ -610,22 +605,22 @@
#define SST_SST28SF040 0x04
#define SST_SST29EE512 0x5D
#define SST_SST29EE010 0x07
-#define SST_SST29LE010 0x08 /* Same as SST29VE010 */
-#define SST_SST29EE020A 0x10 /* Same as SST29EE020 */
-#define SST_SST29LE020 0x12 /* Same as SST29VE020 */
+#define SST_SST29LE010 0x08 /* Same as SST29VE010 */
+#define SST_SST29EE020A 0x10 /* Same as SST29EE020 */
+#define SST_SST29LE020 0x12 /* Same as SST29VE020 */
#define SST_SST29SF020 0x24
#define SST_SST29VF020 0x25
#define SST_SST29SF040 0x13
#define SST_SST29VF040 0x14
#define SST_SST39SF512 0xB4
#define SST_SST39SF010 0xB5
-#define SST_SST39SF020 0xB6 /* Same as 39SF020A */
+#define SST_SST39SF020 0xB6 /* Same as 39SF020A */
#define SST_SST39SF040 0xB7
#define SST_SST39VF512 0xD4
#define SST_SST39VF010 0xD5
-#define SST_SST39VF020 0xD6 /* Same as 39LF020 */
-#define SST_SST39VF040 0xD7 /* Same as 39LF040 */
-#define SST_SST39VF080 0xD8 /* Same as 39LF080/39VF080/39VF088 */
+#define SST_SST39VF020 0xD6 /* Same as 39LF020 */
+#define SST_SST39VF040 0xD7 /* Same as 39LF040 */
+#define SST_SST39VF080 0xD8 /* Same as 39LF080/39VF080/39VF088 */
#define SST_SST49LF040B 0x50
#define SST_SST49LF040 0x51
#define SST_SST49LF020 0x61
@@ -634,7 +629,7 @@
#define SST_SST49LF080A 0x5B
#define SST_SST49LF002A 0x57
#define SST_SST49LF003A 0x1B
-#define SST_SST49LF004A 0x60 /* Same as 49LF004B */
+#define SST_SST49LF004A 0x60 /* Same as 49LF004B */
#define SST_SST49LF008A 0x5A
#define SST_SST49LF004C 0x54
#define SST_SST49LF008C 0x59
@@ -645,34 +640,35 @@
* ST25P chips are SPI, first byte of device ID is memory type, second
* byte of device ID is related to log(bitsize) at least for some chips.
*/
-#define ST_ID 0x20 /* ST / SGS/Thomson / Numonyx (later acquired by Micron) */
-#define ST_M25P05A 0x2010
-#define ST_M25P05_RES 0x10 /* Same code as M25P10. */
-#define ST_M25P10A 0x2011
-#define ST_M25P10_RES 0x10 /* Same code as M25P05. */
-#define ST_M25P20 0x2012
+#define ST_ID 0x20 /* ST / SGS/Thomson / Numonyx (later acquired by Micron) */
+#define ST_M25P05A 0x20, 0x10
+#define ST_M25P05A_RES 0x05
+#define ST_M25P05_RES 0x10 /* Same code as M25P10. */
+#define ST_M25P10A 0x20, 0x11
+#define ST_M25P10_RES 0x10 /* Same code as M25P05. */
+#define ST_M25P20 0x20, 0x12, 0x10
#define ST_M25P20_RES 0x11
-#define ST_M25P40 0x2013
+#define ST_M25P40 0x20, 0x13, 0x10
#define ST_M25P40_RES 0x12
-#define ST_M25P80 0x2014
-#define ST_M25P16 0x2015
-#define ST_M25P32 0x2016
-#define ST_M25P64 0x2017
-#define ST_M25P128 0x2018
-#define ST_M45PE10 0x4011
-#define ST_M45PE20 0x4012
-#define ST_M45PE40 0x4013
-#define ST_M45PE80 0x4014
-#define ST_M45PE16 0x4015
-#define ST_M25PX80 0x7114
-#define ST_M25PX16 0x7115
-#define ST_M25PX32 0x7116
-#define ST_M25PX64 0x7117
-#define ST_M25PE10 0x8011
-#define ST_M25PE20 0x8012
-#define ST_M25PE40 0x8013
-#define ST_M25PE80 0x8014
-#define ST_M25PE16 0x8015
+#define ST_M25P80 0x20, 0x14, 0x10
+#define ST_M25P16 0x20, 0x15
+#define ST_M25P32 0x20, 0x16
+#define ST_M25P64 0x20, 0x17
+#define ST_M25P128 0x20, 0x18
+#define ST_M45PE10 0x40, 0x11
+#define ST_M45PE20 0x40, 0x12
+#define ST_M45PE40 0x40, 0x13
+#define ST_M45PE80 0x40, 0x14
+#define ST_M45PE16 0x40, 0x15
+#define ST_M25PX80 0x71, 0x14
+#define ST_M25PX16 0x71, 0x15
+#define ST_M25PX32 0x71, 0x16
+#define ST_M25PX64 0x71, 0x17
+#define ST_M25PE10 0x80, 0x11
+#define ST_M25PE20 0x80, 0x12
+#define ST_M25PE40 0x80, 0x13
+#define ST_M25PE80 0x80, 0x14
+#define ST_M25PE16 0x80, 0x15
#define ST_M50FLW040A 0x08
#define ST_M50FLW040B 0x28
#define ST_M50FLW080A 0x80
@@ -683,33 +679,33 @@
#define ST_M50FW016 0x2E
#define ST_M50LPW080 0x2F
#define ST_M50LPW116 0x30
-#define ST_M29F002B 0x34 /* Same as M29F002BB */
-#define ST_M29F002T 0xB0 /* Same as M29F002BT/M29F002NT/M29F002BNT */
-#define ST_M29F040B 0xE2 /* Same as M29F040 */
+#define ST_M29F002B 0x34 /* Same as M29F002BB */
+#define ST_M29F002T 0xB0 /* Same as M29F002BT/M29F002NT/M29F002BNT */
+#define ST_M29F040B 0xE2 /* Same as M29F040 */
#define ST_M29F080 0xF1
#define ST_M29F200BT 0xD3
#define ST_M29F200BB 0xD4
-#define ST_M29F400BT 0xD5 /* Same as M29F400T */
-#define ST_M29F400BB 0xD6 /* Same as M29F400B */
+#define ST_M29F400BT 0xD5 /* Same as M29F400T */
+#define ST_M29F400BB 0xD6 /* Same as M29F400B */
#define ST_M29F800DB 0x58
#define ST_M29F800DT 0xEC
#define ST_M29W010B 0x23
#define ST_M29W040B 0xE3
#define ST_M29W512B 0x27
-#define ST_N25Q016__1E 0xBB15 /* N25Q016, 1.8V, (uniform sectors expected) */
-#define ST_N25Q032__3E 0xBA16 /* N25Q032, 3.0V, (uniform sectors expected) */
-#define ST_N25Q032__1E 0xBB16 /* N25Q032, 1.8V, (uniform sectors expected) */
-#define ST_N25Q064__3E 0xBA17 /* N25Q064, 3.0V, (uniform sectors expected) */
-#define ST_N25Q064__1E 0xBB17 /* N25Q064, 1.8V, (uniform sectors expected) */
-#define ST_N25Q128__3E 0xBA18 /* N25Q128, 3.0V, (uniform sectors expected) */
-#define ST_N25Q128__1E 0xBB18 /* N25Q128, 1.8V, (uniform sectors expected) */
-#define ST_N25Q256__3E 0xBA19 /* N25Q256, 3.0V, (uniform sectors expected) */
-#define ST_N25Q256__1E 0xBB19 /* N25Q256, 1.8V, (uniform sectors expected) */
-#define ST_N25Q512__3E 0xBA20 /* N25Q512, 3.0V, (uniform sectors expected) */
-#define ST_N25Q512__1E 0xBB20 /* N25Q512, 1.8V, (uniform sectors expected) */
-#define ST_N25Q00A__3E 0xBA21 /* N25Q00A, 3.0V, (uniform sectors expected) */
-
-#define SYNCMOS_MVC_ID 0x40 /* SyncMOS (SM) and Mosel Vitelic Corporation (MVC) */
+#define ST_N25Q016__1E 0xBB, 0x15 /* N25Q016, 1.8V, (uniform sectors expected) */
+#define ST_N25Q032__3E 0xBA, 0x16 /* N25Q032, 3.0V, (uniform sectors expected) */
+#define ST_N25Q032__1E 0xBB, 0x16 /* N25Q032, 1.8V, (uniform sectors expected) */
+#define ST_N25Q064__3E 0xBA, 0x17 /* N25Q064, 3.0V, (uniform sectors expected) */
+#define ST_N25Q064__1E 0xBB, 0x17 /* N25Q064, 1.8V, (uniform sectors expected) */
+#define ST_N25Q128__3E 0xBA, 0x18 /* N25Q128, 3.0V, (uniform sectors expected) */
+#define ST_N25Q128__1E 0xBB, 0x18 /* N25Q128, 1.8V, (uniform sectors expected) */
+#define ST_N25Q256__3E 0xBA, 0x19 /* N25Q256, 3.0V, (uniform sectors expected) */
+#define ST_N25Q256__1E 0xBB, 0x19 /* N25Q256, 1.8V, (uniform sectors expected) */
+#define ST_N25Q512__3E 0xBA, 0x20 /* N25Q512, 3.0V, (uniform sectors expected) */
+#define ST_N25Q512__1E 0xBB, 0x20 /* N25Q512, 1.8V, (uniform sectors expected) */
+#define ST_N25Q00A__3E 0xBA, 0x21 /* N25Q00A, 3.0V, (uniform sectors expected) */
+
+#define SYNCMOS_MVC_ID 0x40 /* SyncMOS (SM) and Mosel Vitelic Corporation (MVC) */
#define MVC_V29C51000T 0x00
#define MVC_V29C51400T 0x13
#define MVC_V29LC51000 0x20
@@ -717,17 +713,17 @@
#define MVC_V29LC51002 0x82
#define MVC_V29C51000B 0xA0
#define MVC_V29C51400B 0xB3
-#define SM_MVC_29C51001T 0x01 /* Identical chips: {F,S,V}29C51001T */
-#define SM_MVC_29C51002T 0x02 /* Identical chips: {F,S,V}29C51002T */
-#define SM_MVC_29C51004T 0x03 /* Identical chips: {F,S,V}29C51004T */
-#define SM_MVC_29C31004T 0x63 /* Identical chips: {S,V}29C31004T */
-#define SM_MVC_29C31004B 0x73 /* Identical chips: {S,V}29C31004B */
-#define SM_MVC_29C51001B 0xA1 /* Identical chips: {F,S,V}29C51001B */
-#define SM_MVC_29C51002B 0xA2 /* Identical chips: {F,S,V}29C51002B */
-#define SM_MVC_29C51004B 0xA3 /* Identical chips: {F,S,V}29C51004B */
-
-#define TI_ID 0x97 /* Texas Instruments */
-#define TI_OLD_ID 0x01 /* TI chips from last century */
+#define SM_MVC_29C51001T 0x01 /* Identical chips: {F,S,V}29C51001T */
+#define SM_MVC_29C51002T 0x02 /* Identical chips: {F,S,V}29C51002T */
+#define SM_MVC_29C51004T 0x03 /* Identical chips: {F,S,V}29C51004T */
+#define SM_MVC_29C31004T 0x63 /* Identical chips: {S,V}29C31004T */
+#define SM_MVC_29C31004B 0x73 /* Identical chips: {S,V}29C31004B */
+#define SM_MVC_29C51001B 0xA1 /* Identical chips: {F,S,V}29C51001B */
+#define SM_MVC_29C51002B 0xA2 /* Identical chips: {F,S,V}29C51002B */
+#define SM_MVC_29C51004B 0xA3 /* Identical chips: {F,S,V}29C51004B */
+
+#define TI_ID 0x97 /* Texas Instruments */
+#define TI_OLD_ID 0x01 /* TI chips from last century */
#define TI_TMS29F002RT 0xB0
#define TI_TMS29F002RB 0x34
@@ -735,44 +731,44 @@
* W25X chips are SPI, first byte of device ID is memory type, second
* byte of device ID is related to log(bitsize).
*/
-#define WINBOND_NEX_ID 0xEF /* Winbond (ex Nexcom) serial flashes */
-#define WINBOND_NEX_W25X10 0x3011
-#define WINBOND_NEX_W25X20 0x3012
-#define WINBOND_NEX_W25X40 0x3013
-#define WINBOND_NEX_W25X80 0x3014
-#define WINBOND_NEX_W25X16 0x3015
-#define WINBOND_NEX_W25X32 0x3016
-#define WINBOND_NEX_W25X64 0x3017
-#define WINBOND_NEX_W25Q40_V 0x4013 /* W25Q40BV; W25Q40BL (2.3-3.6V) */
-#define WINBOND_NEX_W25Q80_V 0x4014 /* W25Q80BV */
-#define WINBOND_NEX_W25Q16_V 0x4015 /* W25Q16CV; W25Q16DV */
-#define WINBOND_NEX_W25Q32_V 0x4016 /* W25Q32BV; W25Q32FV in SPI mode (default) */
-#define WINBOND_NEX_W25Q64_V 0x4017 /* W25Q64BV, W25Q64CV; W25Q64FV in SPI mode (default) */
-#define WINBOND_NEX_W25Q128_V 0x4018 /* W25Q128BV; W25Q128FV in SPI mode (default) */
-#define WINBOND_NEX_W25Q256_V 0x4019 /* W25Q256FV */
-#define WINBOND_NEX_W25Q20_W 0x5012 /* W25Q20BW */
-#define WINBOND_NEX_W25Q40_W 0x5013 /* W25Q40BW */
-#define WINBOND_NEX_W25Q80_W 0x5014 /* W25Q80BW */
-#define WINBOND_NEX_W25Q16_W 0x6015 /* W25Q16DW */
-#define WINBOND_NEX_W25Q32_W 0x6016 /* W25Q32DW; W25Q32FV in QPI mode */
-#define WINBOND_NEX_W25Q64_W 0x6017 /* W25Q64DW; W25Q64FV in QPI mode */
-#define WINBOND_NEX_W25Q128_W 0x6018 /* (No W version known) W25Q128FV in QPI mode */
-
-#define WINBOND_ID 0xDA /* Winbond */
+#define WINBOND_NEX_ID 0xEF /* Winbond (ex Nexcom) serial flashes */
+#define WINBOND_NEX_W25X10 0x30, 0x11
+#define WINBOND_NEX_W25X20 0x30, 0x12
+#define WINBOND_NEX_W25X40 0x30, 0x13
+#define WINBOND_NEX_W25X80 0x30, 0x14
+#define WINBOND_NEX_W25X16 0x30, 0x15
+#define WINBOND_NEX_W25X32 0x30, 0x16
+#define WINBOND_NEX_W25X64 0x30, 0x17
+#define WINBOND_NEX_W25Q40_V 0x40, 0x13 /* W25Q40BV; W25Q40BL (2.3-3.6V) */
+#define WINBOND_NEX_W25Q80_V 0x40, 0x14 /* W25Q80BV */
+#define WINBOND_NEX_W25Q16_V 0x40, 0x15 /* W25Q16CV; W25Q16DV */
+#define WINBOND_NEX_W25Q32_V 0x40, 0x16 /* W25Q32BV; W25Q32FV in SPI mode (default) */
+#define WINBOND_NEX_W25Q64_V 0x40, 0x17 /* W25Q64BV, W25Q64CV; W25Q64FV in SPI mode (default) */
+#define WINBOND_NEX_W25Q128_V 0x40, 0x18 /* W25Q128BV; W25Q128FV in SPI mode (default) */
+#define WINBOND_NEX_W25Q256_V 0x40, 0x19 /* W25Q256FV */
+#define WINBOND_NEX_W25Q20_W 0x50, 0x12 /* W25Q20BW */
+#define WINBOND_NEX_W25Q40_W 0x50, 0x13 /* W25Q40BW */
+#define WINBOND_NEX_W25Q80_W 0x50, 0x14 /* W25Q80BW */
+#define WINBOND_NEX_W25Q16_W 0x60, 0x15 /* W25Q16DW */
+#define WINBOND_NEX_W25Q32_W 0x60, 0x16 /* W25Q32DW; W25Q32FV in QPI mode */
+#define WINBOND_NEX_W25Q64_W 0x60, 0x17 /* W25Q64DW; W25Q64FV in QPI mode */
+#define WINBOND_NEX_W25Q128_W 0x60, 0x18 /* (No W version known) W25Q128FV in QPI mode */
+
+#define WINBOND_ID 0xDA /* Winbond */
#define WINBOND_W19B160BB 0x49
#define WINBOND_W19B160BT 0xC4
-#define WINBOND_W19B320SB 0x2A /* Same as W19L320SB */
-#define WINBOND_W19B320ST 0xBA /* Same as W19L320ST */
+#define WINBOND_W19B320SB 0x2A /* Same as W19L320SB */
+#define WINBOND_W19B320ST 0xBA /* Same as W19L320ST */
#define WINBOND_W19B322MB 0x92
#define WINBOND_W19B322MT 0x10
#define WINBOND_W19B323MB 0x94
#define WINBOND_W19B323MT 0x13
#define WINBOND_W19B324MB 0x97
#define WINBOND_W19B324MT 0x16
-#define WINBOND_W29C010 0xC1 /* Same as W29C010M, W29C011A, W29EE011, W29EE012, and ASD AE29F1008 */
-#define WINBOND_W29C020 0x45 /* Same as W29C020C, W29C022 and ASD AE29F2008 */
-#define WINBOND_W29C040 0x46 /* Same as W29C040P */
-#define WINBOND_W29C512A 0xC8 /* Same as W29EE512 */
+#define WINBOND_W29C010 0xC1 /* Same as W29C010M, W29C011A, W29EE011, W29EE012, and ASD AE29F1008 */
+#define WINBOND_W29C020 0x45 /* Same as W29C020C, W29C022 and ASD AE29F2008 */
+#define WINBOND_W29C040 0x46 /* Same as W29C040P */
+#define WINBOND_W29C512A 0xC8 /* Same as W29EE512 */
#define WINBOND_W39F010 0xA1
#define WINBOND_W39L010 0x31
#define WINBOND_W39L020 0xB5
@@ -781,13 +777,13 @@
#define WINBOND_W39L512 0x38
#define WINBOND_W39V040A 0x3D
#define WINBOND_W39V040FA 0x34
-#define WINBOND_W39V040B 0x54 /* Same as W39V040FB */
-#define WINBOND_W39V040C 0x50 /* Same as W39V040FC */
+#define WINBOND_W39V040B 0x54 /* Same as W39V040FB */
+#define WINBOND_W39V040C 0x50 /* Same as W39V040FC */
#define WINBOND_W39V080A 0xD0
#define WINBOND_W39V080FA 0xD3
-#define WINBOND_W39V080FA_DM 0x93 /* W39V080FA dual mode */
-#define WINBOND_W49F002 0x25 /* Same as W49F002B */
-#define WINBOND_W49F002U 0x0B /* Same as W49F002N and ASD AE49F2008 */
+#define WINBOND_W39V080FA_DM 0x93 /* W39V080FA dual mode */
+#define WINBOND_W49F002 0x25 /* Same as W49F002B */
+#define WINBOND_W49F002U 0x0B /* Same as W49F002N and ASD AE49F2008 */
#define WINBOND_W49F020 0x8C
#define WINBOND_W49V002A 0xB0
#define WINBOND_W49V002FA 0x32
diff --git a/flashrom.c b/flashrom.c
index e613768..e7c5781 100644
--- a/flashrom.c
+++ b/flashrom.c
@@ -36,7 +36,7 @@
#include <sys/utsname.h>
#endif
#include "flash.h"
-#include "flashchips.h"
+#include "chipdrivers.h"
#include "programmer.h"
#include "hwaccess.h"
@@ -364,6 +364,12 @@ static bool all_skipped = true;
static int check_block_eraser(const struct flashctx *flash, int k, int log);
+int shutdown_free(void *data)
+{
+ free(data);
+ return 0;
+}
+
/* Register a function to be executed on programmer shutdown.
* The advantage over atexit() is that you can supply a void pointer which will
* be used as parameter to the registered function upon programmer shutdown.
@@ -1085,107 +1091,302 @@ int map_flash(struct flashctx *flash)
return 0;
}
-int probe_flash(struct registered_programmer *pgm, int startchip, struct flashctx *flash, int force)
+static probe probes[] = {
+ { &probe_spi_rdid, BUS_SPI, "RDID"},
+ { &probe_spi_res, BUS_SPI, "RES"},
+ { &probe_spi_rems, BUS_SPI, "REMS"},
+ { &probe_spi_at25f, BUS_SPI, "AT25F"},
+ { &probe_spi_at45db, BUS_SPI, "AT45DB"},
+ { &probe_jedec_longreset, BUS_PARALLEL, "JEDEC long", 64, 512, 1},
+ { &probe_jedec_shortreset_full, BUS_PARALLEL | BUS_LPC | BUS_FWH, "JEDEC short full", 64, 1024, 1},
+ { &probe_jedec_shortreset_full_384, BUS_FWH, "JEDEC short full 384k", 384, 384}, // workaround for SST49LF003A/B
+ { &probe_jedec_shortreset_aaa, BUS_PARALLEL, "JEDEC short AAA", 256, 256},
+ { &probe_jedec_shortreset_2aa, BUS_PARALLEL, "JEDEC short 2AA", 64, 2048, 1},
+ { &probe_82802ab_unshifted, BUS_PARALLEL | BUS_LPC | BUS_FWH, "82802AB", 256, 2048, 1},
+ { &probe_82802ab_shifted, BUS_PARALLEL | BUS_LPC | BUS_FWH, "82802AB shifted", 256, 2048, 1},
+ { &probe_w29ee011, BUS_PARALLEL , "W29EE011", 128, 128},
+ { &probe_en29lv640b, BUS_PARALLEL , "EN29LV640B", 8192, 8192},
+ { &probe_m29f400bt, BUS_PARALLEL , "M29F400BT", 512, 2048, 2},
+};
+
+int probe_allsizes(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
{
- const struct flashchip *chip;
- uint32_t size;
- enum chipbustype buses_common;
- char *tmp;
+ uint16_t size_min = p->size_min;
+ uint16_t size_max = p->size_max;
+ uint16_t size_step = p->size_step;
+ if (res_len == 0 || size_min == 0)
+ return -1;
- for (chip = flashchips + startchip; chip && chip->name; chip++) {
- if (chip_to_probe && strcmp(chip->name, chip_to_probe) != 0)
- continue;
- buses_common = pgm->buses_supported & chip->bustype;
- if (!buses_common)
+ if (size_step == 0) {
+ size_step = 1;
+ msg_cspew("%s: setting step size to 1.\n", __func__);
+ }
+
+ if (size_min > size_max) {
+ size_max = size_min;
+ msg_cspew("%s: setting max size to min size.\n", __func__);
+ }
+
+ /* Probe for chips of multiple sizes with one function (pointer) */
+ int res_cnt = 0;
+ unsigned int s;
+ for (s = size_min; s <= size_max; s <<= size_step) {
+ void *addr = programmer_map_flash_region("probe_allsizes", 0xffffffff - s * 1024 + 1, s * 1024);
+ if (addr == ERROR_PTR) {
+ msg_cwarn("%s: Could not map physical memory to probe for size %d kB.", __func__, s);
continue;
- msg_gdbg("Probing for %s %s, %d kB: ", chip->vendor, chip->name, chip->total_size);
- if (!chip->probe && !force) {
- msg_gdbg("failed! flashrom has no probe function for this flash chip.\n");
+ }
+ flash->virtual_memory = (chipaddr)addr;
+ msg_cdbg("size %d... ", s);
+ int ret = p->probe_func(flash, res, res_len - res_cnt, p);
+ programmer_unmap_flash_region((void *)flash->virtual_memory, s * 1024);
+ if (ret >= 1) {
+ msg_cspew("%s: size %d returned %d result(s).\n", __func__, s, ret);
+ res->chip_size = s;
+ res += ret;
+ res_cnt += ret;
+ res_len -= ret;
+ } else if (ret <= 0)
+ res->len = 0;
+ if (res_len == 0) {
+ msg_cdbg("%s: Maximum number of results reached after probing for size %d kB. ",
+ __func__, s);
+ break;
+ }
+ }
+ return res_cnt;
+}
+
+/* Probe for regular chips on a single programmer. */
+static unsigned int probe_flash_int(struct flashctx **flashes, unsigned int flashes_len, struct registered_programmer *pgm)
+{
+ unsigned int matches_prog = 0;
+ /* First, obtain results of all possible probe functions on this programmer. */
+ probe_res results[30] = {{0}}; //fixme
+ unsigned int results_cnt = 0;
+ unsigned int valid_results = 0;
+ unsigned int p_cnt;
+ for (p_cnt = 0; p_cnt < ARRAY_SIZE(probes); p_cnt++) {
+ if (results_cnt == ARRAY_SIZE(results)) {
+ msg_cwarn("%s: Maximum number of results (%ld) reached after %d probers. ",
+ __func__, ARRAY_SIZE(results), p_cnt);
+ break;
+ }
+ probe *p = &probes[p_cnt];
+ probe_res *res = &results[results_cnt];
+ if ((p->bustype & pgm->buses_supported) == 0)
continue;
+ msg_gdbg("Probing with %s... ", p->mnemonic);
+ struct flashctx ctx = {.pgm = pgm};
+ int ret;
+ if (p->size_min != 0 || p->size_max != 0 || p->size_step != 0) {
+ ret = probe_allsizes(&ctx, res, ARRAY_SIZE(results) - results_cnt, p);
+ } else {
+ ret = p->probe_func(&ctx, res, ARRAY_SIZE(results) - results_cnt, p);
}
+ msg_gdbg("done: %d.\n", ret);
+
+ res->probe_func = p->probe_func;
+ if (ret > 0) {
+ unsigned int i, j;
+ for (i = 0; i < ret; i++) {
+ bool valid = false;
+ for (j = 0; j < res->len; j++) {
+ msg_cdbg(" 0x%02x", res->vals[j]);
+ /* All zeros or all ones is most probably not a valid result, but any
+ * byte containing something else makes the response valid. */
+ if (res->vals[j] != 0x00 && res->vals[j] != 0xFF) {
+ valid = true;
+ }
+ }
+ if (valid)
+ valid_results++;
+ else
+ msg_cdbg(" Invalid result.");
- /* Start filling in the dynamic data. */
- flash->chip = calloc(1, sizeof(struct flashchip));
- if (!flash->chip) {
- msg_gerr("Out of memory!\n");
- exit(1);
+ if (res->len > 0)
+ msg_cdbg("\n");
+
+ res++;
+ }
+ results_cnt += ret;
}
- memcpy(flash->chip, chip, sizeof(struct flashchip));
- flash->pgm = pgm;
+ }
- if (map_flash(flash) != 0)
- return -1;
+ if (valid_results == 0) {
+ char *busses = flashbuses_to_text(pgm->buses_supported);
+ msg_cdbg("No valid probing results received for %s.\n", busses);
+ free(busses);
+ return 0;
+ }
- size = chip->total_size * 1024;
- /* We handle a forced match like a real match, we just avoid probing. Note that probe_flash()
- * is only called with force=1 after normal probing failed.
- */
- if (force)
- break;
+ /* Try to find matching chips. For each chip in the flashchips array, compare its stored probers
+ * with the results obtained above. */
+ const struct flashchip *chip;
+ for (chip = flashchips; chip->name; chip++) {
+ if ((chip->bustype & pgm->buses_supported) == 0)
+ continue;
+ msg_cdbg2("Matching %s... ", chip->name);
+ bool mismatch = false; // set if any received result does not match the saved values
+ bool match = false; // set if at least one result matches
+ unsigned int want_cnt;
+ for (want_cnt = 0; want_cnt < ARRAY_SIZE(chip->probers); want_cnt++) {
+ const struct prober *want = &chip->probers[want_cnt];
+ if (want->func == NULL)
+ break; /* If there is a prober w/o a func we are done for this chip. */
+
+ msg_cspew("\nComaring ID #%d: ", want_cnt);
+
+ /* Look for the matching probe function and compare its result to the chip. */
+ for (p_cnt = 0; p_cnt < ARRAY_SIZE(probes); p_cnt++) {
+ probe *p = &probes[p_cnt];
+ if (want->func != p->probe_func) {
+ msg_cspew("want->func != p->probe_func, ");
+ continue; // look further for the current probe function
+ }
- if (flash->chip->probe(flash) != 1)
- goto notfound;
+ probe_res *res = NULL;
+ unsigned int i;
+ for (i = 0; i < results_cnt; i++) {
+ if (results[i].probe_func == want->func &&
+ (results[i].chip_size == 0 ||
+ results[i].chip_size == chip->total_size)) {
+ res = &results[i];
+ // there should only be 1 result for any size, use first found
+ break;
+ }
+ }
+ if (res == NULL || res->len == 0) {
+ msg_cspew("no result for probe #%d, ", p_cnt);
+ break; // right function but there is no result -> next function
+ }
- /* If this is the first chip found, accept it.
- * If this is not the first chip found, accept it only if it is
- * a non-generic match. SFDP and CFI are generic matches.
- * startchip==0 means this call to probe_flash() is the first
- * one for this programmer interface and thus no other chip has
- * been found on this interface.
- */
- if (startchip == 0 && flash->chip->model_id == SFDP_DEVICE_ID) {
- msg_cinfo("===\n"
- "SFDP has autodetected a flash chip which is "
- "not natively supported by flashrom yet.\n");
- if (count_usable_erasers(flash) == 0)
- msg_cinfo("The standard operations read and "
- "verify should work, but to support "
- "erase, write and all other "
- "possible features");
- else
- msg_cinfo("All standard operations (read, "
- "verify, erase and write) should "
- "work, but to support all possible "
- "features");
-
- msg_cinfo(" we need to add them manually.\n"
- "You can help us by mailing us the output of the following command to "
- "flashrom@flashrom.org:\n"
- "'flashrom -VV [plus the -p/--programmer parameter]'\n"
- "Thanks for your help!\n"
- "===\n");
+ msg_cspew("comparing %d bytes of probe #%d... ",
+ min(res->len, want->res.len), p_cnt);
+
+ bool seen_vendor = false;
+ for (i = 0; i < min(res->len, want->res.len); i++) {
+ if (!seen_vendor && res->vals[i] != 0x7F && res->vals[i] != 0x00 &&
+ res->vals[i] != 0xFF) {
+ seen_vendor = true;
+ if (!oddparity(res->vals[i]))
+ msg_cdbg("%s byte %d parity violation.\n",
+ p->mnemonic, i);
+ }
+ if (res->vals[i] != want->res.vals[i]) {
+ msg_cspew("byte #%d unexpected (0x%02x != 0x%02x), ",
+ i, res->vals[i], want->res.vals[i]);
+ mismatch = true;
+ goto chip_done; // a single mismatch is enough to abort
+ }
+ }
+ msg_cspew("all match. ");
+ match = true; // remember that at least one prober has matched
+ break; // skip to next prober
+ }
+ }
+chip_done:
+ msg_cdbg2("%s does%s match.\n", chip->name, match && !mismatch ? "" : " not");
+ if (match && !mismatch) {
+ char *busses = flashbuses_to_text(chip->bustype);
+ msg_cinfo("Found %s flash chip \"%s\" (%d kB, %s).\n",
+ chip->vendor, chip->name, chip->total_size, busses);
+ free(busses);
+ struct flashctx *tmp = realloc(*flashes, sizeof(struct flashctx) * (flashes_len + 1));
+ if (tmp == NULL) {
+ msg_gerr("Out of memory!\n");
+ free(*flashes);
+ *flashes = NULL;
+ return -1;
+ }
+ tmp[flashes_len].pgm = pgm;
+ tmp[flashes_len].chip = chip;
+ if (chip->printlock != NULL)
+ chip->printlock(&tmp[flashes_len]);
+ *flashes = tmp;
+ flashes_len++;
+ matches_prog++;
}
-
- /* First flash chip detected on this bus. */
- if (startchip == 0)
- break;
- /* Not the first flash chip detected on this bus, but not a generic match either. */
- if ((flash->chip->model_id != GENERIC_DEVICE_ID) && (flash->chip->model_id != SFDP_DEVICE_ID))
- break;
- /* Not the first flash chip detected on this bus, and it's just a generic match. Ignore it. */
-notfound:
- unmap_flash(flash);
- free(flash->chip);
- flash->chip = NULL;
}
+ return matches_prog;
+}
- if (!flash->chip)
- return -1;
+int probe_flash(struct flashctx **flashes, const struct registered_programmer *prog)
+{
+ unsigned int matches_total = 0;
+ unsigned int pgm_cnt;
+ for (pgm_cnt = 0; pgm_cnt < registered_programmer_count; pgm_cnt++) {
+ struct registered_programmer *pgm = ®istered_programmers[pgm_cnt];
+ int matches_prog = probe_flash_int(flashes, matches_total, pgm);
+ if (matches_prog < 0) {
+ msg_cerr("%s: probe_flash_int for programmer #%d returned an error, aborting.",
+ __func__, pgm_cnt);
+ free(*flashes);
+ return -1;
+ }
- tmp = flashbuses_to_text(flash->chip->bustype);
- msg_cinfo("%s %s flash chip \"%s\" (%d kB, %s).\n", force ? "Assuming" : "Found",
- flash->chip->vendor, flash->chip->name, flash->chip->total_size, tmp);
- free(tmp);
+ matches_total += matches_prog;
- /* Flash registers will not be mapped if the chip was forced. Lock info
- * may be stored in registers, so avoid lock info printing.
- */
- if (!force)
- if (flash->chip->printlock)
- flash->chip->printlock(flash);
+ if (pgm->buses_supported & BUS_SPI) {
+ /* Try to detect SFDP only if there are no specific matches for this programmer. */
+ if (matches_prog == 0) {
+ struct flashctx *tmp = realloc(*flashes, sizeof(struct flashctx) * (matches_total + 1));
+ if (tmp == NULL) {
+ msg_gerr("Out of memory!\n");
+ free(*flashes);
+ return -1;
+ }
+ *flashes = tmp;
+ flashes[matches_total]->pgm = pgm;
+ if (probe_spi_sfdp(flashes[matches_total]) == 1) {
+ msg_cinfo("===\n"
+ "SFDP has autodetected a flash chip which is "
+ "not natively supported by flashrom yet.\n");
+ if (count_usable_erasers(flashes[matches_total]) == 0)
+ msg_cinfo("The standard operations read and "
+ "verify should work, but to support "
+ "erase, write and all other "
+ "possible features");
+ else
+ msg_cinfo("All standard operations (read, "
+ "verify, erase and write) should "
+ "work, but to support all possible "
+ "features");
+
+ msg_cinfo(" we need to add them manually.\n"
+ "You can help us by mailing us the output of the following "
+ "command to flashrom@flashrom.org:\n"
+ "'flashrom -VV [plus the -p/--programmer parameters]'\n"
+ "Thanks for your help!\n"
+ "===\n");
+ matches_total++;
+ }
+ }
+ }
+ }
- /* Return position of matching chip. */
- return chip - flashchips;
+ /* Similar to SFDP above but here we check that there were no matches whatsoever at the very end of
+ * probing so that everything else gets precedence. */
+ if (matches_total == 0) {
+ for (pgm_cnt = 0; pgm_cnt < registered_programmer_count; pgm_cnt++) {
+ struct registered_programmer *pgm = ®istered_programmers[pgm_cnt];
+ if (pgm->buses_supported & BUS_PROG) {
+ struct flashctx *tmp = realloc(*flashes, sizeof(struct flashctx) * (matches_total + 1));
+ if (tmp == NULL) {
+ msg_gerr("Out of memory!\n");
+ free(*flashes);
+ return -1;
+ }
+ *flashes = tmp;
+ flashes[matches_total]->pgm = pgm;
+ if (pgm->opaque.probe(flashes[matches_total]) == 0) {
+ matches_total++;
+ }
+ }
+ }
+ }
+
+ return matches_total;
}
int read_buf_from_file(unsigned char *buf, unsigned long size,
@@ -1888,6 +2089,9 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it,
return 1;
}
+ if (map_flash(flash) != 0)
+ return 1;
+
/* Given the existence of read locks, we want to unlock for read,
* erase and write.
*/
diff --git a/ichspi.c b/ichspi.c
index 190ad5a..c56f336 100644
--- a/ichspi.c
+++ b/ichspi.c
@@ -204,6 +204,7 @@ typedef struct _OPCODES {
static OPCODES *curopcodes = NULL;
+
/* HW access functions */
static uint32_t REGREAD32(int X)
{
@@ -1187,36 +1188,58 @@ static int ich_hwseq_wait_for_cycle_complete(unsigned int timeout,
return 0;
}
+static int ich_hwseq_read(struct flashctx *flash, uint8_t *buf, unsigned int addr, unsigned int len);
+static int ich_hwseq_block_erase(struct flashctx *flash, unsigned int addr, unsigned int len);
+static int ich_hwseq_write(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len);
static int ich_hwseq_probe(struct flashctx *flash)
{
uint32_t total_size, boundary;
uint32_t erase_size_low, size_low, erase_size_high, size_high;
- struct block_eraser *eraser;
total_size = hwseq_data.size_comp0 + hwseq_data.size_comp1;
- msg_cdbg("Found %d attached SPI flash chip",
+ msg_cdbg("Hardware sequencing has found %d attached SPI flash chip",
(hwseq_data.size_comp1 != 0) ? 2 : 1);
if (hwseq_data.size_comp1 != 0)
msg_cdbg("s with a combined");
else
msg_cdbg(" with a");
msg_cdbg(" density of %d kB.\n", total_size / 1024);
- flash->chip->total_size = total_size / 1024;
- eraser = &(flash->chip->block_erasers[0]);
+ struct flashchip *hwseq_chip = calloc(1, sizeof(struct flashchip));
+ if (hwseq_chip == NULL) {
+ msg_gerr("Out of memory!\n");
+ return -1;
+ }
+ if (register_shutdown(shutdown_free, (void *)hwseq_chip) != 0) {
+ msg_gerr("%s: Could not reqister shutdown function!\n", __func__);
+ free(hwseq_chip);
+ return -1;
+ }
+
+ hwseq_chip->vendor = "Intel";
+ hwseq_chip->name = "Flash chip(s) behind hardware sequencing";
+ hwseq_chip->bustype = BUS_PROG;
+ hwseq_chip->page_size = 256;
+ hwseq_chip->tested = TEST_OK_PREW;
+ hwseq_chip->block_erasers[0].block_erase = ich_hwseq_block_erase;
+ hwseq_chip->write = ich_hwseq_write;
+ hwseq_chip->read = ich_hwseq_read;
+ hwseq_chip->total_size = total_size / 1024;
+
+ struct block_eraser *eraser = &(hwseq_chip->block_erasers[0]);
boundary = (REGREAD32(ICH9_REG_FPB) & FPB_FPBA) << 12;
size_high = total_size - boundary;
erase_size_high = ich_hwseq_get_erase_block_size(boundary);
if (boundary == 0) {
- msg_cdbg("There is only one partition containing the whole "
+ msg_cdbg2("There is only one partition containing the whole "
"address space (0x%06x - 0x%06x).\n", 0, size_high-1);
eraser->eraseblocks[0].size = erase_size_high;
eraser->eraseblocks[0].count = size_high / erase_size_high;
- msg_cdbg("There are %d erase blocks with %d B each.\n",
+ msg_cdbg2("There are %d erase blocks with %d B each.\n",
size_high / erase_size_high, erase_size_high);
} else {
- msg_cdbg("The flash address space (0x%06x - 0x%06x) is divided "
+ msg_cdbg2("The flash address space (0x%06x - 0x%06x) is divided "
"at address 0x%06x in two partitions.\n",
0, total_size-1, boundary);
size_low = total_size - size_high;
@@ -1224,20 +1247,20 @@ static int ich_hwseq_probe(struct flashctx *flash)
eraser->eraseblocks[0].size = erase_size_low;
eraser->eraseblocks[0].count = size_low / erase_size_low;
- msg_cdbg("The first partition ranges from 0x%06x to 0x%06x.\n",
+ msg_cdbg2("The first partition ranges from 0x%06x to 0x%06x.\n",
0, size_low-1);
- msg_cdbg("In that range are %d erase blocks with %d B each.\n",
+ msg_cdbg2("In that range are %d erase blocks with %d B each.\n",
size_low / erase_size_low, erase_size_low);
eraser->eraseblocks[1].size = erase_size_high;
eraser->eraseblocks[1].count = size_high / erase_size_high;
- msg_cdbg("The second partition ranges from 0x%06x to 0x%06x.\n",
+ msg_cdbg2("The second partition ranges from 0x%06x to 0x%06x.\n",
boundary, total_size-1);
- msg_cdbg("In that range are %d erase blocks with %d B each.\n",
+ msg_cdbg2("In that range are %d erase blocks with %d B each.\n",
size_high / erase_size_high, erase_size_high);
}
- flash->chip->tested = TEST_OK_PREW;
- return 1;
+ flash->chip = hwseq_chip;
+ return 0;
}
static int ich_hwseq_block_erase(struct flashctx *flash, unsigned int addr,
@@ -1547,9 +1570,6 @@ static const struct opaque_programmer opaque_programmer_ich_hwseq = {
.max_data_read = 64,
.max_data_write = 64,
.probe = ich_hwseq_probe,
- .read = ich_hwseq_read,
- .write = ich_hwseq_write,
- .erase = ich_hwseq_block_erase,
};
int ich_init_spi(struct pci_dev *dev, void *spibar, enum ich_chipset ich_gen)
diff --git a/jedec.c b/jedec.c
index d8c3242..dbf3fd7 100644
--- a/jedec.c
+++ b/jedec.c
@@ -38,6 +38,30 @@ uint8_t oddparity(uint8_t val)
return (val ^ (val >> 1)) & 0x1;
}
+/* Looks for values in a different from all zeroes and all ones. If b is non-null test_for_valid_ids
+ * additionally compares bytes in a and b respectively. Can be be used on values read before and after exiting
+ * ID mode: Unequal values indicate with high certainty that the write commands enabling and disabling ID mode
+ * were received and understood by the chip. */
+bool test_for_valid_ids(uint8_t *a, uint8_t *b, unsigned int len)
+{
+ unsigned int i;
+ bool equal = true;
+ bool valid = false;
+ for (i = 0; i < len; i++) {
+ if (b != NULL) {
+ if (a[i] != b[i])
+ equal = false;
+ else
+ msg_cspew("Byte #%d is equal (0x%02x).\n", i, a[i]);
+ }
+ if (a[i] != 0x00 && a[i] != 0xFF)
+ valid = true;
+ }
+ if (b != NULL && equal && valid)
+ msg_cdbg("IDs are equal to normal flash content.");
+ return valid;
+}
+
static void toggle_ready_jedec_common(const struct flashctx *flash, chipaddr dst, unsigned int delay)
{
unsigned int i = 0;
@@ -120,15 +144,10 @@ static void start_program_jedec_common(const struct flashctx *flash, unsigned in
chip_writeb(flash, 0xA0, bios + (0x5555 & mask));
}
-int probe_jedec(struct flashctx *flash)
+static int probe_jedec(struct flashctx *flash, struct probe_res *res, unsigned int mask, bool long_reset)
{
unsigned int delay = 10000;
chipaddr bios = flash->virtual_memory;
- const struct flashchip *chip = flash->chip;
- const unsigned int mask = getaddrmask(flash->chip);
- uint8_t id1, id2;
- uint32_t largeid1, largeid2;
- uint32_t flashcontent1, flashcontent2;
/* Earlier probes might have been too fast for the chip to enter ID
* mode completely. Allow the chip to finish this before seeing a
@@ -137,7 +156,7 @@ int probe_jedec(struct flashctx *flash)
if (delay)
programmer_delay(delay);
/* Reset chip to a clean slate */
- if ((chip->feature_bits & FEATURE_RESET_MASK) == FEATURE_LONG_RESET)
+ if (long_reset)
{
chip_writeb(flash, 0xAA, bios + (0x5555 & mask));
if (delay)
@@ -161,26 +180,25 @@ int probe_jedec(struct flashctx *flash)
if (delay)
programmer_delay(delay);
- /* Read product ID */
- id1 = chip_readb(flash, bios);
- id2 = chip_readb(flash, bios + 0x01);
- largeid1 = id1;
- largeid2 = id2;
-
- /* Check if it is a continuation ID, this should be a while loop. */
- if (id1 == 0x7F) {
- largeid1 <<= 8;
- id1 = chip_readb(flash, bios + 0x100);
- largeid1 |= id1;
+#if (NUM_PROBE_BYTES < 4)
+#error probe_jedec requires NUM_PROBE_BYTES to be at least 4.
+#endif
+ unsigned int idx = 0;
+ /* Read manufacturer ID */
+ res->vals[idx++] = chip_readb(flash, bios);
+ /* Check if it is a continuation ID, this (and the one below) should be a while loop. */
+ if (res->vals[idx] == 0x7F) {
+ res->vals[idx++] = chip_readb(flash, bios + 0x100);
}
- if (id2 == 0x7F) {
- largeid2 <<= 8;
- id2 = chip_readb(flash, bios + 0x101);
- largeid2 |= id2;
+
+ /* Read model ID */
+ res->vals[idx++] = chip_readb(flash, bios + 0x01);
+ if (res->vals[idx] == 0x7F) {
+ res->vals[idx++] = chip_readb(flash, bios + 0x101);
}
/* Issue JEDEC Product ID Exit command */
- if ((chip->feature_bits & FEATURE_RESET_MASK) == FEATURE_LONG_RESET)
+ if (long_reset)
{
chip_writeb(flash, 0xAA, bios + (0x5555 & mask));
if (delay)
@@ -193,36 +211,56 @@ int probe_jedec(struct flashctx *flash)
if (delay)
programmer_delay(delay);
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x", __func__, largeid1, largeid2);
- if (!oddparity(id1))
- msg_cdbg(", id1 parity violation");
-
+ uint8_t cont[idx];
+ unsigned cont_idx = 0;
/* Read the product ID location again. We should now see normal flash contents. */
- flashcontent1 = chip_readb(flash, bios);
- flashcontent2 = chip_readb(flash, bios + 0x01);
+ cont[cont_idx] = chip_readb(flash, bios);
/* Check if it is a continuation ID, this should be a while loop. */
- if (flashcontent1 == 0x7F) {
- flashcontent1 <<= 8;
- flashcontent1 |= chip_readb(flash, bios + 0x100);
+ if (cont[cont_idx++] == 0x7F) {
+ cont[cont_idx++] = chip_readb(flash, bios + 0x100);
}
- if (flashcontent2 == 0x7F) {
- flashcontent2 <<= 8;
- flashcontent2 |= chip_readb(flash, bios + 0x101);
+ cont[cont_idx] = chip_readb(flash, bios + 0x01);
+ if (cont[cont_idx++] == 0x7F) {
+ cont[cont_idx++] = chip_readb(flash, bios + 0x101);
}
- if (largeid1 == flashcontent1)
- msg_cdbg(", id1 is normal flash content");
- if (largeid2 == flashcontent2)
- msg_cdbg(", id2 is normal flash content");
-
- msg_cdbg("\n");
- if (largeid1 != chip->manufacture_id || largeid2 != chip->model_id)
+ if (test_for_valid_ids(res->vals, cont, idx)) {
+ res->len = idx;
+ return 1;
+ } else {
+ res->len = 0;
return 0;
+ }
return 1;
}
+int probe_jedec_longreset(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
+{
+ return probe_jedec(flash, res, MASK_FULL, true);
+}
+
+int probe_jedec_shortreset_full(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
+{
+ return probe_jedec(flash, res, MASK_FULL, false);
+}
+
+int probe_jedec_shortreset_full_384(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
+{
+ return probe_jedec(flash, res, MASK_FULL, false);
+}
+
+int probe_jedec_shortreset_2aa(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
+{
+ return probe_jedec(flash, res, MASK_2AA, false);
+}
+
+int probe_jedec_shortreset_aaa(struct flashctx *flash, struct probe_res *res, unsigned int res_len, const struct probe *p)
+{
+ return probe_jedec(flash, res, MASK_AAA, false);
+}
+
static int erase_sector_jedec_common(struct flashctx *flash, unsigned int page,
unsigned int pagesize, unsigned int mask)
{
diff --git a/m29f400bt.c b/m29f400bt.c
index 399a7e0..0a13076 100644
--- a/m29f400bt.c
+++ b/m29f400bt.c
@@ -55,10 +55,9 @@ int write_m29f400bt(struct flashctx *flash, const uint8_t *src, unsigned int sta
return 0;
}
-int probe_m29f400bt(struct flashctx *flash)
+int probe_m29f400bt(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
chipaddr bios = flash->virtual_memory;
- uint8_t id1, id2;
chip_writeb(flash, 0xAA, bios + 0xAAA);
chip_writeb(flash, 0x55, bios + 0x555);
@@ -66,11 +65,14 @@ int probe_m29f400bt(struct flashctx *flash)
programmer_delay(10);
- id1 = chip_readb(flash, bios);
+#if (NUM_PROBE_BYTES < 2)
+#error probe_m29f400bt requires NUM_PROBE_BYTES to be at least 2.
+#endif
+ res->vals[0] = chip_readb(flash, bios);
/* The data sheet says id2 is at (bios + 0x01) and id2 listed in
* flash.h does not match. It should be possible to use JEDEC probe.
*/
- id2 = chip_readb(flash, bios + 0x02);
+ res->vals[1] = chip_readb(flash, bios + 0x02);
chip_writeb(flash, 0xAA, bios + 0xAAA);
chip_writeb(flash, 0x55, bios + 0x555);
@@ -78,10 +80,15 @@ int probe_m29f400bt(struct flashctx *flash)
programmer_delay(10);
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x\n", __func__, id1, id2);
+ uint8_t cont[2];
+ cont[0] = chip_readb(flash, bios);
+ cont[1] = chip_readb(flash, bios + 0x02);
- if (id1 == flash->chip->manufacture_id && id2 == flash->chip->model_id)
+ if (test_for_valid_ids(res->vals, cont, 2)) {
+ res->len = 2;
return 1;
-
- return 0;
+ } else {
+ res->len = 0;
+ return 0;
+ }
}
diff --git a/opaque.c b/opaque.c
index c63919f..3a9866c 100644
--- a/opaque.c
+++ b/opaque.c
@@ -30,31 +30,11 @@
#include "chipdrivers.h"
#include "programmer.h"
-int probe_opaque(struct flashctx *flash)
-{
- return flash->pgm->opaque.probe(flash);
-}
-
-int read_opaque(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len)
-{
- return flash->pgm->opaque.read(flash, buf, start, len);
-}
-
-int write_opaque(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len)
-{
- return flash->pgm->opaque.write(flash, buf, start, len);
-}
-
-int erase_opaque(struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen)
-{
- return flash->pgm->opaque.erase(flash, blockaddr, blocklen);
-}
-
int register_opaque_programmer(const struct opaque_programmer *pgm)
{
struct registered_programmer rpgm;
- if (!pgm->probe || !pgm->read || !pgm->write || !pgm->erase) {
+ if (!pgm->probe) {
msg_perr("%s called with incomplete programmer definition. "
"Please report a bug at flashrom(a)flashrom.org\n",
__func__);
diff --git a/print.c b/print.c
index efd834d..22d1d64 100644
--- a/print.c
+++ b/print.c
@@ -109,11 +109,6 @@ static int print_supported_chips(void)
/* calculate maximum column widths and by iterating over all chips */
for (chip = flashchips; chip->name != NULL; chip++) {
- /* Ignore generic entries. */
- if (!strncmp(chip->vendor, "Unknown", 7) ||
- !strncmp(chip->vendor, "Programmer", 10) ||
- !strncmp(chip->name, "unknown", 7))
- continue;
chipcount++;
/* Find maximum vendor length (respecting line splitting). */
@@ -195,15 +190,9 @@ static int print_supported_chips(void)
msg_ginfo(" ");
msg_gdbg("range [V]");
msg_ginfo("\n\n");
- msg_ginfo("(P = PROBE, R = READ, E = ERASE, W = WRITE)\n\n");
+ msg_ginfo("(P = PROBE, R = READ, E = ERASE, W = WRITE, - = N/A)\n\n");
for (chip = flashchips; chip->name != NULL; chip++) {
- /* Don't print generic entries. */
- if (!strncmp(chip->vendor, "Unknown", 7) ||
- !strncmp(chip->vendor, "Programmer", 10) ||
- !strncmp(chip->name, "unknown", 7))
- continue;
-
/* support for multiline vendor names:
* - make a copy of the original vendor name
* - use strok to put the first token in tmpven
diff --git a/print_wiki.c b/print_wiki.c
index 2936dbf..8c64a80 100644
--- a/print_wiki.c
+++ b/print_wiki.c
@@ -292,11 +292,6 @@ static void print_supported_chips_wiki(int cols)
int i = 0, c = 1, chipcount = 0;
for (f = flashchips; f->name != NULL; f++) {
- /* Don't count generic entries. */
- if (!strncmp(f->vendor, "Unknown", 7) ||
- !strncmp(f->vendor, "Programmer", 10) ||
- !strncmp(f->name, "unknown", 7))
- continue;
chipcount++;
}
@@ -308,12 +303,6 @@ static void print_supported_chips_wiki(int cols)
"{| border=\"0\" valign=\"top\"\n", chipcount);
for (f = flashchips; f->name != NULL; f++) {
- /* Don't print generic entries. */
- if (!strncmp(f->vendor, "Unknown", 7) ||
- !strncmp(f->vendor, "Programmer", 10) ||
- !strncmp(f->name, "unknown", 7))
- continue;
-
if ((i % lines_per_col) == 0)
printf("%s%s", th_start, chip_th);
diff --git a/programmer.c b/programmer.c
index 1874929..f677891 100644
--- a/programmer.c
+++ b/programmer.c
@@ -119,7 +119,7 @@ struct registered_programmer registered_programmers[PROGRAMMERS_MAX];
int registered_programmer_count = 0;
/* This function copies the struct registered_programmer parameter. */
-int register_programmer(struct registered_programmer *pgm)
+int register_programmer(const struct registered_programmer *pgm)
{
if (registered_programmer_count >= PROGRAMMERS_MAX) {
msg_perr("Tried to register more than %i programmer "
diff --git a/programmer.h b/programmer.h
index 9b0227e..9ab7698 100644
--- a/programmer.h
+++ b/programmer.h
@@ -629,9 +629,6 @@ struct opaque_programmer {
int max_data_write;
/* Specific functions for this programmer */
int (*probe) (struct flashctx *flash);
- int (*read) (struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
- int (*write) (struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
- int (*erase) (struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen);
const void *data;
};
int register_opaque_programmer(const struct opaque_programmer *pgm);
@@ -669,7 +666,7 @@ struct registered_programmer {
};
extern struct registered_programmer registered_programmers[];
extern int registered_programmer_count;
-int register_programmer(struct registered_programmer *pgm);
+int register_programmer(const struct registered_programmer *pgm);
/* serprog.c */
#if CONFIG_SERPROG == 1
diff --git a/sfdp.c b/sfdp.c
index bc69dd0..488115d 100644
--- a/sfdp.c
+++ b/sfdp.c
@@ -256,51 +256,30 @@ static int sfdp_fill_flash(struct flashchip *chip, uint8_t *buf, uint16_t len)
}
done:
+ chip->vendor = "Unknown";
+ chip->name = "SFDP-capable chip";
+ chip->bustype = BUS_SPI;
+ /* We present our own "report this" text hence we do not
+ * want the default "This flash part has status UNTESTED..."
+ * text to be printed. */
+ chip->tested = TEST_OK_PREW;
+ chip->unlock = spi_disable_blockprotect; /* is this safe? */
+ chip->read = spi_chip_read;
+ /* FIXME: some vendor extensions define voltage ranges too. */
+
msg_cdbg("done.\n");
return 0;
}
-int probe_spi_sfdp(struct flashctx *flash)
+static int sfdp_parse_headers(struct flashctx *flash, struct flashchip *sfdp_chip, uint8_t nph)
{
- int ret = 0;
- uint8_t buf[8];
uint32_t tmp32;
- uint8_t nph;
/* need to limit the table loop by comparing i to uint8_t nph hence: */
uint16_t i;
struct sfdp_tbl_hdr *hdrs;
uint8_t *hbuf;
uint8_t *tbuf;
-
- if (spi_sfdp_read_sfdp(flash, 0x00, buf, 4)) {
- msg_cdbg("Receiving SFDP signature failed.\n");
- return 0;
- }
- tmp32 = buf[0];
- tmp32 |= ((unsigned int)buf[1]) << 8;
- tmp32 |= ((unsigned int)buf[2]) << 16;
- tmp32 |= ((unsigned int)buf[3]) << 24;
-
- if (tmp32 != 0x50444653) {
- msg_cdbg2("Signature = 0x%08x (should be 0x50444653)\n", tmp32);
- msg_cdbg("No SFDP signature found.\n");
- return 0;
- }
-
- if (spi_sfdp_read_sfdp(flash, 0x04, buf, 3)) {
- msg_cdbg("Receiving SFDP revision and number of parameter "
- "headers (NPH) failed. ");
- return 0;
- }
- msg_cdbg2("SFDP revision = %d.%d\n", buf[1], buf[0]);
- if (buf[1] != 0x01) {
- msg_cdbg("The chip supports an unknown version of SFDP. "
- "Aborting SFDP probe!\n");
- return 0;
- }
- nph = buf[2];
- msg_cdbg2("SFDP number of parameter headers is %d (NPH = %d).\n",
- nph + 1, nph);
+ int ret = 1;
/* Fetch all parameter headers, even if we don't use them all (yet). */
hbuf = malloc((nph + 1) * 8);
@@ -381,8 +360,8 @@ int probe_spi_sfdp(struct flashctx *flash)
msg_cdbg("Length of the mandatory JEDEC SFDP "
"parameter table is wrong (%d B), "
"skipping it.\n", len);
- } else if (sfdp_fill_flash(flash->chip, tbuf, len) == 0)
- ret = 1;
+ } else
+ ret = sfdp_fill_flash(sfdp_chip, tbuf, len);
}
free(tbuf);
}
@@ -390,5 +369,63 @@ int probe_spi_sfdp(struct flashctx *flash)
cleanup_hdrs:
free(hdrs);
free(hbuf);
+
+ return ret;
+}
+
+int probe_spi_sfdp(struct flashctx *flash)
+{
+ int ret = -1;
+ uint8_t buf[8];
+ uint32_t tmp32;
+
+ msg_cdbg("Looking for a SFDP-compatible chip... ");
+ if (spi_sfdp_read_sfdp(flash, 0x00, buf, 4)) {
+ msg_cdbg("Receiving SFDP signature failed.\n");
+ return -1;
+ }
+ tmp32 = buf[0];
+ tmp32 |= ((unsigned int)buf[1]) << 8;
+ tmp32 |= ((unsigned int)buf[2]) << 16;
+ tmp32 |= ((unsigned int)buf[3]) << 24;
+
+ if (tmp32 != 0x50444653) {
+ msg_cdbg2("Signature = 0x%08x (should be 0x50444653)\n", tmp32);
+ msg_cdbg("No SFDP signature found.\n");
+ return 0;
+ }
+
+ if (spi_sfdp_read_sfdp(flash, 0x04, buf, 3)) {
+ msg_cdbg("Receiving SFDP revision and number of parameter "
+ "headers (NPH) failed. ");
+ return -1;
+ }
+ msg_cdbg2("SFDP revision = %d.%d\n", buf[1], buf[0]);
+ if (buf[1] != 0x01) {
+ msg_cdbg("The chip supports an unknown version of SFDP. "
+ "Aborting SFDP probe!\n");
+ return 0;
+ }
+ msg_cdbg2("SFDP number of parameter headers is %d (NPH = %d).\n",
+ buf[2] + 1, buf[2]);
+
+ struct flashchip *sfdp_chip = calloc(1, sizeof(struct flashchip));
+ if (sfdp_chip == NULL) {
+ msg_gerr("Out of memory!\n");
+ return -1;
+ }
+
+ ret = sfdp_parse_headers(flash, sfdp_chip, buf[2]);
+
+ if (ret == 0) {
+ if (register_shutdown(shutdown_free, (void *)sfdp_chip) != 0) {
+ msg_gerr("%s: Could not reqister shutdown function!\n", __func__);
+ free(sfdp_chip);
+ return -1;
+ }
+ flash->chip = sfdp_chip;
+ } else
+ free(sfdp_chip);
+
return ret;
}
diff --git a/spi25.c b/spi25.c
index 9763c80..38846f9 100644
--- a/spi25.c
+++ b/spi25.c
@@ -29,68 +29,40 @@
#include "programmer.h"
#include "spi.h"
-static int spi_rdid(struct flashctx *flash, unsigned char *readarr, int bytes)
+static int spi_rdid(struct flashctx *flash, unsigned char *readarr, unsigned int bytes)
{
- static const unsigned char cmd[JEDEC_RDID_OUTSIZE] = { JEDEC_RDID };
- int ret;
- int i;
-
- ret = spi_send_command(flash, sizeof(cmd), bytes, cmd, readarr);
- if (ret)
- return ret;
- msg_cspew("RDID returned");
- for (i = 0; i < bytes; i++)
- msg_cspew(" 0x%02x", readarr[i]);
- msg_cspew(". ");
- return 0;
+ static const unsigned char cmd[] = { JEDEC_RDID };
+ if (spi_send_command(flash, sizeof(cmd), bytes, cmd, readarr) != 0)
+ return -1;
+ return test_for_valid_ids(readarr, NULL, bytes) ? 1 : 0;
}
-static int spi_rems(struct flashctx *flash, unsigned char *readarr)
+static int probe_spi_res_rems(struct flashctx *flash, struct probe_res *res, uint8_t opcode)
{
- unsigned char cmd[JEDEC_REMS_OUTSIZE] = { JEDEC_REMS, 0, 0, 0 };
- uint32_t readaddr;
- int ret;
-
- ret = spi_send_command(flash, sizeof(cmd), JEDEC_REMS_INSIZE, cmd,
- readarr);
+ unsigned char cmd[] = { opcode, 0, 0, 0 }; /* opcode + address */
+ res->len = ARRAY_SIZE(res->vals); // fill up to maximum if possible
+ int ret = spi_send_command(flash, sizeof(cmd), res->len, cmd, res->vals);
if (ret == SPI_INVALID_ADDRESS) {
/* Find the lowest even address allowed for reads. */
- readaddr = (spi_get_valid_read_addr(flash) + 1) & ~1;
+ uint32_t readaddr = (spi_get_valid_read_addr(flash) + 1) & ~1;
cmd[1] = (readaddr >> 16) & 0xff,
cmd[2] = (readaddr >> 8) & 0xff,
cmd[3] = (readaddr >> 0) & 0xff,
- ret = spi_send_command(flash, sizeof(cmd), JEDEC_REMS_INSIZE,
- cmd, readarr);
+ ret = spi_send_command(flash, sizeof(cmd), res->len, cmd, res->vals);
}
- if (ret)
- return ret;
- msg_cspew("REMS returned 0x%02x 0x%02x. ", readarr[0], readarr[1]);
- return 0;
+ if (ret != 0)
+ return -1;
+ return test_for_valid_ids(res->vals, NULL, res->len) ? 1 : 0;
}
-static int spi_res(struct flashctx *flash, unsigned char *readarr, int bytes)
+int probe_spi_rems(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- unsigned char cmd[JEDEC_RES_OUTSIZE] = { JEDEC_RES, 0, 0, 0 };
- uint32_t readaddr;
- int ret;
- int i;
+ return probe_spi_res_rems(flash, res, JEDEC_REMS);
+}
- ret = spi_send_command(flash, sizeof(cmd), bytes, cmd, readarr);
- if (ret == SPI_INVALID_ADDRESS) {
- /* Find the lowest even address allowed for reads. */
- readaddr = (spi_get_valid_read_addr(flash) + 1) & ~1;
- cmd[1] = (readaddr >> 16) & 0xff,
- cmd[2] = (readaddr >> 8) & 0xff,
- cmd[3] = (readaddr >> 0) & 0xff,
- ret = spi_send_command(flash, sizeof(cmd), bytes, cmd, readarr);
- }
- if (ret)
- return ret;
- msg_cspew("RES returned");
- for (i = 0; i < bytes; i++)
- msg_cspew(" 0x%02x", readarr[i]);
- msg_cspew(". ");
- return 0;
+int probe_spi_res(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
+{
+ return probe_spi_res_rems(flash, res, JEDEC_RES);
}
int spi_write_enable(struct flashctx *flash)
@@ -115,210 +87,37 @@ int spi_write_disable(struct flashctx *flash)
return spi_send_command(flash, sizeof(cmd), 0, cmd, NULL);
}
-static int probe_spi_rdid_generic(struct flashctx *flash, int bytes)
+int probe_spi_rdid(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- const struct flashchip *chip = flash->chip;
- unsigned char readarr[4];
- uint32_t id1;
- uint32_t id2;
-
- if (spi_rdid(flash, readarr, bytes)) {
- return 0;
- }
-
- if (!oddparity(readarr[0]))
- msg_cdbg("RDID byte 0 parity violation. ");
-
- /* Check if this is a continuation vendor ID.
- * FIXME: Handle continuation device IDs.
- */
- if (readarr[0] == 0x7f) {
- if (!oddparity(readarr[1]))
- msg_cdbg("RDID byte 1 parity violation. ");
- id1 = (readarr[0] << 8) | readarr[1];
- id2 = readarr[2];
- if (bytes > 3) {
- id2 <<= 8;
- id2 |= readarr[3];
- }
- } else {
- id1 = readarr[0];
- id2 = (readarr[1] << 8) | readarr[2];
- }
-
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x\n", __func__, id1, id2);
-
- if (id1 == chip->manufacture_id && id2 == chip->model_id)
- return 1;
-
- /* Test if this is a pure vendor match. */
- if (id1 == chip->manufacture_id && GENERIC_DEVICE_ID == chip->model_id)
- return 1;
-
- /* Test if there is any vendor ID. */
- if (GENERIC_MANUF_ID == chip->manufacture_id && id1 != 0xff)
- return 1;
-
- return 0;
-}
-
-int probe_spi_rdid(struct flashctx *flash)
-{
- return probe_spi_rdid_generic(flash, 3);
-}
-
-int probe_spi_rdid4(struct flashctx *flash)
-{
- /* Some SPI controllers do not support commands with writecnt=1 and
- * readcnt=4.
- */
- switch (flash->pgm->spi.type) {
+ res->len = ARRAY_SIZE(res->vals); // fill up to maximum if possible
+ /* Some SPI controllers do not support commands with writecnt=1 and readcnt=4. */
+ if (res->len != 3) { // FIXME
+ switch (flash->pgm->spi.type) {
#if CONFIG_INTERNAL == 1
#if defined(__i386__) || defined(__x86_64__)
- case SPI_CONTROLLER_IT87XX:
- case SPI_CONTROLLER_WBSIO:
- msg_cinfo("4 byte RDID not supported on this SPI controller\n");
- return 0;
- break;
+ case SPI_CONTROLLER_IT87XX:
+ case SPI_CONTROLLER_WBSIO:
+ msg_cinfo("4 byte RDID not supported on this SPI controller\n");
+ return -1;
+ break;
#endif
#endif
- default:
- return probe_spi_rdid_generic(flash, 4);
- }
-
- return 0;
-}
-
-int probe_spi_rems(struct flashctx *flash)
-{
- const struct flashchip *chip = flash->chip;
- unsigned char readarr[JEDEC_REMS_INSIZE];
- uint32_t id1, id2;
-
- if (spi_rems(flash, readarr)) {
- return 0;
- }
-
- id1 = readarr[0];
- id2 = readarr[1];
-
- msg_cdbg("%s: id1 0x%x, id2 0x%x\n", __func__, id1, id2);
-
- if (id1 == chip->manufacture_id && id2 == chip->model_id)
- return 1;
-
- /* Test if this is a pure vendor match. */
- if (id1 == chip->manufacture_id && GENERIC_DEVICE_ID == chip->model_id)
- return 1;
-
- /* Test if there is any vendor ID. */
- if (GENERIC_MANUF_ID == chip->manufacture_id && id1 != 0xff)
- return 1;
-
- return 0;
-}
-
-int probe_spi_res1(struct flashctx *flash)
-{
- static const unsigned char allff[] = {0xff, 0xff, 0xff};
- static const unsigned char all00[] = {0x00, 0x00, 0x00};
- unsigned char readarr[3];
- uint32_t id2;
-
- /* We only want one-byte RES if RDID and REMS are unusable. */
-
- /* Check if RDID is usable and does not return 0xff 0xff 0xff or
- * 0x00 0x00 0x00. In that case, RES is pointless.
- */
- if (!spi_rdid(flash, readarr, 3) && memcmp(readarr, allff, 3) &&
- memcmp(readarr, all00, 3)) {
- msg_cdbg("Ignoring RES in favour of RDID.\n");
- return 0;
- }
- /* Check if REMS is usable and does not return 0xff 0xff or
- * 0x00 0x00. In that case, RES is pointless.
- */
- if (!spi_rems(flash, readarr) &&
- memcmp(readarr, allff, JEDEC_REMS_INSIZE) &&
- memcmp(readarr, all00, JEDEC_REMS_INSIZE)) {
- msg_cdbg("Ignoring RES in favour of REMS.\n");
- return 0;
- }
-
- if (spi_res(flash, readarr, 1)) {
- return 0;
- }
-
- id2 = readarr[0];
-
- msg_cdbg("%s: id 0x%x\n", __func__, id2);
-
- if (id2 != flash->chip->model_id)
- return 0;
-
- return 1;
-}
-
-int probe_spi_res2(struct flashctx *flash)
-{
- unsigned char readarr[2];
- uint32_t id1, id2;
-
- if (spi_res(flash, readarr, 2)) {
- return 0;
- }
-
- id1 = readarr[0];
- id2 = readarr[1];
-
- msg_cdbg("%s: id1 0x%x, id2 0x%x\n", __func__, id1, id2);
-
- if (id1 != flash->chip->manufacture_id || id2 != flash->chip->model_id)
- return 0;
-
- return 1;
-}
-
-int probe_spi_res3(struct flashctx *flash)
-{
- unsigned char readarr[3];
- uint32_t id1, id2;
-
- if (spi_res(flash, readarr, 3)) {
- return 0;
+ default:
+ ;//return probe_spi_rdid_generic(flash, 4);
+ }
}
- id1 = (readarr[0] << 8) | readarr[1];
- id2 = readarr[2];
-
- msg_cdbg("%s: id1 0x%x, id2 0x%x\n", __func__, id1, id2);
-
- if (id1 != flash->chip->manufacture_id || id2 != flash->chip->model_id)
- return 0;
-
- return 1;
+ return spi_rdid(flash, res->vals, res->len);
}
/* Only used for some Atmel chips. */
-int probe_spi_at25f(struct flashctx *flash)
+int probe_spi_at25f(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- static const unsigned char cmd[AT25F_RDID_OUTSIZE] = { AT25F_RDID };
- unsigned char readarr[AT25F_RDID_INSIZE];
- uint32_t id1;
- uint32_t id2;
-
- if (spi_send_command(flash, sizeof(cmd), sizeof(readarr), cmd, readarr))
- return 0;
-
- id1 = readarr[0];
- id2 = readarr[1];
-
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x\n", __func__, id1, id2);
-
- if (id1 == flash->chip->manufacture_id && id2 == flash->chip->model_id)
- return 1;
-
- return 0;
+ static const uint8_t cmd[AT25F_RDID_OUTSIZE] = { AT25F_RDID };
+ res->len = AT25F_RDID_INSIZE;
+ if (spi_send_command(flash, sizeof(cmd), res->len, cmd, res->vals) != 0)
+ return -1;
+ return test_for_valid_ids(res->vals, NULL, res->len) ? 1 : 0;
}
int spi_chip_erase_60(struct flashctx *flash)
diff --git a/stm50.c b/stm50.c
index edcfdd2..168a4a2 100644
--- a/stm50.c
+++ b/stm50.c
@@ -53,7 +53,7 @@ static int stm50_unlock_address(struct flashctx *flash, int offset)
int unlock_stm50_nonuniform(struct flashctx *flash)
{
int i;
- struct eraseblock *eraseblocks = flash->chip->block_erasers[0].eraseblocks;
+ const struct eraseblock *eraseblocks = flash->chip->block_erasers[0].eraseblocks;
unsigned int done = 0;
for (i = 0; i < NUM_ERASEREGIONS && eraseblocks[i].count != 0; i++) {
unsigned int block_size = eraseblocks[i].size;
diff --git a/w29ee011.c b/w29ee011.c
index 4df4687..1dbbb35 100644
--- a/w29ee011.c
+++ b/w29ee011.c
@@ -20,23 +20,22 @@
#include <string.h>
#include "flash.h"
+#include "chipdrivers.h"
/* According to the Winbond W29EE011, W29EE012, W29C010M, W29C011A
* datasheets this is the only valid probe function for those chips.
*/
-int probe_w29ee011(struct flashctx *flash)
+int probe_w29ee011(struct flashctx *flash, struct probe_res *res, unsigned int ignored, const struct probe *ignored2)
{
- chipaddr bios = flash->virtual_memory;
- uint8_t id1, id2;
-
- if (!chip_to_probe || strcmp(chip_to_probe, flash->chip->name)) {
- msg_cdbg("Old Winbond W29* probe method disabled because "
- "the probing sequence puts the AMIC A49LF040A in "
- "a funky state. Use 'flashrom -c %s' if you "
- "have a board with such a chip.\n", flash->chip->name);
+ static const char *w29ee011 = "W29C010(M)/W29C011A/W29EE011/W29EE012-old";
+ if (!chip_to_probe || (strcmp(chip_to_probe, w29ee011) != 0)) {
+ msg_cdbg("Old Winbond W29* probe method disabled because the probing sequence puts the\n"
+ "AMIC A49LF040A in a funky state. Use 'flashrom -c \"%s\"' if you have a board\n"
+ "with such a chip.\n", w29ee011);
return 0;
}
+ chipaddr bios = flash->virtual_memory;
/* Issue JEDEC Product ID Entry command */
chip_writeb(flash, 0xAA, bios + 0x5555);
programmer_delay(10);
@@ -51,9 +50,12 @@ int probe_w29ee011(struct flashctx *flash)
chip_writeb(flash, 0x60, bios + 0x5555);
programmer_delay(10);
+#if (NUM_PROBE_BYTES < 2)
+#error probe_w29ee011 requires NUM_PROBE_BYTES to be at least 2.
+#endif
/* Read product ID */
- id1 = chip_readb(flash, bios);
- id2 = chip_readb(flash, bios + 0x01);
+ res->vals[0] = chip_readb(flash, bios);
+ res->vals[1] = chip_readb(flash, bios + 0x01);
/* Issue JEDEC Product ID Exit command */
chip_writeb(flash, 0xAA, bios + 0x5555);
@@ -63,10 +65,17 @@ int probe_w29ee011(struct flashctx *flash)
chip_writeb(flash, 0xF0, bios + 0x5555);
programmer_delay(10);
- msg_cdbg("%s: id1 0x%02x, id2 0x%02x\n", __func__, id1, id2);
+ uint8_t cont[2];
+ cont[0] = chip_readb(flash, bios);
+ cont[1] = chip_readb(flash, bios + 0x01);
- if (id1 == flash->chip->manufacture_id && id2 == flash->chip->model_id)
+ if (test_for_valid_ids(res->vals, cont, 2)) {
+ res->len = 2;
return 1;
+ } else {
+ res->len = 0;
+ return 0;
+ }
- return 0;
+ return 1;
}
--
Kind regards, Stefan Tauner
1
0
Previously we did map the physical memory corresponding to all chips,
even for SPI chips where it is completely unnecessary because we do
not use it in any SPI-capable programmer.
Also, the mapping was never undone before the program exited.
Mapping of additional flash registers was done within probing methods
instead of centrally.
Besides all of that, this patch also adds proper error handling for
mapping-related operations.
Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
---
82802ab.c | 2 --
flash.h | 1 -
flashrom.c | 80 ++++++++++++++++++++++++++++++++++++++++++++++----------------
jedec.c | 3 ---
4 files changed, 60 insertions(+), 26 deletions(-)
diff --git a/82802ab.c b/82802ab.c
index cbc775b..d249c3a 100644
--- a/82802ab.c
+++ b/82802ab.c
@@ -82,8 +82,6 @@ static int probe_82802ab(struct flashctx *flash, bool shifted)
if (id1 != flash->chip->manufacture_id || id2 != flash->chip->model_id)
return 0;
- if (flash->chip->feature_bits & FEATURE_REGISTERMAP)
- map_flash_registers(flash);
return 1;
}
diff --git a/flash.h b/flash.h
index 9f75bbc..d26d90b 100644
--- a/flash.h
+++ b/flash.h
@@ -239,7 +239,6 @@ extern int verbose_screen;
extern int verbose_logfile;
extern const char flashrom_version[];
extern const char *chip_to_probe;
-void map_flash_registers(struct flashctx *flash);
int read_memmapped(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len);
int erase_flash(struct flashctx *flash);
int probe_flash(struct registered_programmer *pgm, int startchip, struct flashctx *fill_flash, int force);
diff --git a/flashrom.c b/flashrom.c
index e246b51..e613768 100644
--- a/flashrom.c
+++ b/flashrom.c
@@ -519,12 +519,23 @@ void programmer_delay(unsigned int usecs)
programmer_table[programmer].delay(usecs);
}
-void map_flash_registers(struct flashctx *flash)
+int map_flash_registers(struct flashctx *flash)
{
size_t size = flash->chip->total_size * 1024;
/* Flash registers live 4 MByte below the flash. */
- /* FIXME: This is incorrect for nonstandard flashbase. */
- flash->virtual_registers = (chipaddr)programmer_map_flash_region("flash chip registers", (0xFFFFFFFF - 0x400000 - size + 1), size);
+ uintptr_t base = flashbase ? flashbase : (0xffffffff - size + 1);
+ if (base < 0x400000) {
+ msg_perr("Base address is too low to map flash registers.");
+ return 1;
+ }
+ base -= 0x400000;
+ void *addr = programmer_map_flash_region("flash chip registers", base, size);
+ if (addr == ERROR_PTR) {
+ msg_perr("Could not map flash chip registers.\n");
+ return 1;
+ }
+ flash->virtual_registers = (chipaddr)addr;
+ return 0;
}
int read_memmapped(struct flashctx *flash, uint8_t *buf, unsigned int start,
@@ -1038,11 +1049,45 @@ unsigned int count_max_decode_exceedings(struct flashctx *flash)
return limitexceeded;
}
+void unmap_flash(struct flashctx *flash)
+{
+ if (flash->chip->bustype & (BUS_PARALLEL | BUS_LPC | BUS_FWH)) {
+ programmer_unmap_flash_region((void *)flash->virtual_memory, flash->chip->total_size);
+ flash->virtual_memory = 0;
+
+ if (flash->chip->feature_bits & FEATURE_REGISTERMAP && flash->virtual_registers != 0) {
+ programmer_unmap_flash_region((void *)flash->virtual_registers, flash->chip->total_size * 1024);
+ flash->virtual_registers = 0;
+ }
+ }
+}
+
+int map_flash(struct flashctx *flash)
+{
+ const unsigned long size = flash->chip->total_size;
+ if (flash->chip->bustype & (BUS_PARALLEL | BUS_LPC | BUS_FWH)) {
+ uintptr_t base = flashbase ? flashbase : (0xffffffff - size + 1);
+ void *addr = programmer_map_flash_region("flash chip", base, size);
+ if (addr == ERROR_PTR) {
+ msg_perr("Could not map flash chip registers.\n");
+ return 1;
+ }
+ flash->virtual_memory = (chipaddr)addr;
+
+ if (flash->chip->feature_bits & FEATURE_REGISTERMAP) {
+ if (map_flash_registers(flash) != 0) {
+ unmap_flash(flash);
+ return 1;
+ }
+ }
+ }
+
+ return 0;
+}
+
int probe_flash(struct registered_programmer *pgm, int startchip, struct flashctx *flash, int force)
{
const struct flashchip *chip;
- unsigned long base = 0;
- char location[64];
uint32_t size;
enum chipbustype buses_common;
char *tmp;
@@ -1068,10 +1113,10 @@ int probe_flash(struct registered_programmer *pgm, int startchip, struct flashct
memcpy(flash->chip, chip, sizeof(struct flashchip));
flash->pgm = pgm;
- size = chip->total_size * 1024;
- base = flashbase ? flashbase : (0xffffffff - size + 1);
- flash->virtual_memory = (chipaddr)programmer_map_flash_region("flash chip", base, size);
+ if (map_flash(flash) != 0)
+ return -1;
+ size = chip->total_size * 1024;
/* We handle a forced match like a real match, we just avoid probing. Note that probe_flash()
* is only called with force=1 after normal probing failed.
*/
@@ -1119,8 +1164,7 @@ int probe_flash(struct registered_programmer *pgm, int startchip, struct flashct
break;
/* Not the first flash chip detected on this bus, and it's just a generic match. Ignore it. */
notfound:
- programmer_unmap_flash_region((void *)flash->virtual_memory, size);
- flash->virtual_memory = (chipaddr)NULL;
+ unmap_flash(flash);
free(flash->chip);
flash->chip = NULL;
}
@@ -1128,16 +1172,9 @@ notfound:
if (!flash->chip)
return -1;
-#if CONFIG_INTERNAL == 1
- if (programmer_table[programmer].map_flash_region == physmap)
- snprintf(location, sizeof(location), "at physical address 0x%lx", base);
- else
-#endif
- snprintf(location, sizeof(location), "on %s", programmer_table[programmer].name);
-
tmp = flashbuses_to_text(flash->chip->bustype);
- msg_cinfo("%s %s flash chip \"%s\" (%d kB, %s) %s.\n", force ? "Assuming" : "Found",
- flash->chip->vendor, flash->chip->name, flash->chip->total_size, tmp, location);
+ msg_cinfo("%s %s flash chip \"%s\" (%d kB, %s).\n", force ? "Assuming" : "Found",
+ flash->chip->vendor, flash->chip->name, flash->chip->total_size, tmp);
free(tmp);
/* Flash registers will not be mapped if the chip was forced. Lock info
@@ -1858,7 +1895,8 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it,
flash->chip->unlock(flash);
if (read_it) {
- return read_flash_to_file(flash, filename);
+ ret = read_flash_to_file(flash, filename);
+ goto unmap;
}
oldcontents = malloc(size);
@@ -1977,5 +2015,7 @@ int doit(struct flashctx *flash, int force, const char *filename, int read_it,
out:
free(oldcontents);
free(newcontents);
+unmap:
+ unmap_flash(flash);
return ret;
}
diff --git a/jedec.c b/jedec.c
index 1cfa677..d8c3242 100644
--- a/jedec.c
+++ b/jedec.c
@@ -220,9 +220,6 @@ int probe_jedec(struct flashctx *flash)
if (largeid1 != chip->manufacture_id || largeid2 != chip->model_id)
return 0;
- if (chip->feature_bits & FEATURE_REGISTERMAP)
- map_flash_registers(flash);
-
return 1;
}
--
Kind regards, Stefan Tauner
1
0
Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at>
---
82802ab.c | 13 +++++++++++--
chipdrivers.h | 3 ++-
flash.h | 3 +--
flashchips.c | 54 ++++++++++++++++++++++++++----------------------------
4 files changed, 40 insertions(+), 33 deletions(-)
diff --git a/82802ab.c b/82802ab.c
index 9e39852..cbc775b 100644
--- a/82802ab.c
+++ b/82802ab.c
@@ -40,11 +40,10 @@ void print_status_82802ab(uint8_t status)
msg_cdbg("%s", status & 0x2 ? "WP|TBL#|WP#,ABORT:" : "UNLOCK:");
}
-int probe_82802ab(struct flashctx *flash)
+static int probe_82802ab(struct flashctx *flash, bool shifted)
{
chipaddr bios = flash->virtual_memory;
uint8_t id1, id2, flashcontent1, flashcontent2;
- int shifted = (flash->chip->feature_bits & FEATURE_ADDR_SHIFTED) != 0;
/* Reset to get a clean state */
chip_writeb(flash, 0xFF, bios);
@@ -89,6 +88,16 @@ int probe_82802ab(struct flashctx *flash)
return 1;
}
+int probe_82802ab_shifted(struct flashctx *flash)
+{
+ return probe_82802ab(flash, true);
+}
+
+int probe_82802ab_unshifted(struct flashctx *flash)
+{
+ return probe_82802ab(flash, false);
+}
+
/* FIXME: needs timeout */
uint8_t wait_82802ab(struct flashctx *flash)
{
diff --git a/chipdrivers.h b/chipdrivers.h
index 03d922d..11a7191 100644
--- a/chipdrivers.h
+++ b/chipdrivers.h
@@ -127,7 +127,8 @@ int spi_erase_at45cs_sector(struct flashctx *flash, unsigned int addr, unsigned
/* 82802ab.c */
uint8_t wait_82802ab(struct flashctx *flash);
-int probe_82802ab(struct flashctx *flash);
+int probe_82802ab_shifted(struct flashctx *flash);
+int probe_82802ab_unshifted(struct flashctx *flash);
int erase_block_82802ab(struct flashctx *flash, unsigned int page, unsigned int pagesize);
int write_82802ab(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len);
void print_status_82802ab(uint8_t status);
diff --git a/flash.h b/flash.h
index d1bc6a3..9f75bbc 100644
--- a/flash.h
+++ b/flash.h
@@ -112,8 +112,7 @@ enum write_granularity {
#define FEATURE_SHORT_RESET (1 << 4)
#define FEATURE_EITHER_RESET FEATURE_LONG_RESET
#define FEATURE_RESET_MASK (FEATURE_LONG_RESET | FEATURE_SHORT_RESET)
-#define FEATURE_ADDR_SHIFTED (1 << 5)
-#define FEATURE_SLOW_ERASE_CMDS (1 << 6)
+#define FEATURE_SLOW_ERASE_CMDS (1 << 5)
/* Feature bits used for SPI only */
#define FEATURE_WRSR_EWSR (1 << 8)
#define FEATURE_WRSR_WREN (1 << 9)
diff --git a/flashchips.c b/flashchips.c
index d6b3a9f..6e6b3a8 100644
--- a/flashchips.c
+++ b/flashchips.c
@@ -2962,7 +2962,7 @@ const struct flashchip flashchips[] = {
.page_size = 0, /* unused */
.feature_bits = FEATURE_REGISTERMAP, /* TODO: LPC OK too? */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab, /* TODO: 0xff cmd not documented? */
+ .probe = probe_82802ab_unshifted, /* TODO: 0xff cmd not documented? */
.block_erasers =
{
{
@@ -5647,7 +5647,7 @@ const struct flashchip flashchips[] = {
.total_size = 256,
.page_size = 256 * 1024,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -5673,7 +5673,7 @@ const struct flashchip flashchips[] = {
.total_size = 512,
.page_size = 256,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -5695,7 +5695,7 @@ const struct flashchip flashchips[] = {
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -5721,7 +5721,7 @@ const struct flashchip flashchips[] = {
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -5746,9 +5746,8 @@ const struct flashchip flashchips[] = {
.model_id = INTEL_28F400B,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
- .feature_bits = FEATURE_ADDR_SHIFTED,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_shifted,
.block_erasers =
{
{
@@ -5773,9 +5772,8 @@ const struct flashchip flashchips[] = {
.model_id = INTEL_28F400T,
.total_size = 512,
.page_size = 128 * 1024, /* maximal block size */
- .feature_bits = FEATURE_ADDR_SHIFTED,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_shifted,
.block_erasers =
{
{
@@ -5802,7 +5800,7 @@ const struct flashchip flashchips[] = {
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -5826,7 +5824,7 @@ const struct flashchip flashchips[] = {
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -9127,7 +9125,7 @@ const struct flashchip flashchips[] = {
.total_size = 1024,
.page_size = 64 * 1024,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -9157,7 +9155,7 @@ const struct flashchip flashchips[] = {
.page_size = 64 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -10199,7 +10197,7 @@ const struct flashchip flashchips[] = {
.page_size = 256,
.feature_bits = 0,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -10651,7 +10649,7 @@ const struct flashchip flashchips[] = {
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -10714,7 +10712,7 @@ const struct flashchip flashchips[] = {
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -10746,7 +10744,7 @@ const struct flashchip flashchips[] = {
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -10924,7 +10922,7 @@ const struct flashchip flashchips[] = {
.page_size = 4 * 1024,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11180,7 +11178,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11212,7 +11210,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11244,7 +11242,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PRE,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11276,7 +11274,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11308,7 +11306,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11337,7 +11335,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11361,7 +11359,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PR,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11385,7 +11383,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_OK_PREW,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11409,7 +11407,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
@@ -11433,7 +11431,7 @@ const struct flashchip flashchips[] = {
.page_size = 0,
.feature_bits = FEATURE_REGISTERMAP,
.tested = TEST_UNTESTED,
- .probe = probe_82802ab,
+ .probe = probe_82802ab_unshifted,
.block_erasers =
{
{
--
Kind regards, Stefan Tauner
1
0