flashrom

flashrom@flashrom.org

1 participants
9187 discussions

Intel D425KT write not working
by Marek Zakrzewski 27 Jan '12

27 Jan '12

Write is not working, module is 1024kB, ROM is 2048kB. flashrom flashrom v0.9.4-r1486 on Linux 2.6.38.2-xxxx-std-ipv6-64 (x86_64), built with libpci 3.1.7, GCC 4.1.2 20080704 (Red Hat 4.1.2-51), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... delay loop is unreliable, trying to continue OK. -s: No such file or directory dmidecode execution unsuccessful - continuing without DMI info Found chipset "Intel NM10". Enabling flash write... WARNING: Setting 0xdc from 0xa to 0xb on NM10 failed. New value is 0xa. WARNING: SPI Configuration Lockdown activated. PROBLEMS, continuing anyway Found Winbond flash chip "W25Q80" (1024 kB, SPI) at physical address 0xfff00000. No operations were specified. flashrom -Vw flashrom v0.9.4-r1486 on Linux 2.6.38.2-xxxx-std-ipv6-64 (x86_64), built with libpci 3.1.7, GCC 4.1.2 20080704 (Red Hat 4.1.2-51), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 372M loops per second, delay more than 10% too short (got 82% of expected delay), recalculating... 363M loops per second, delay more than 10% too short (got 80% of expected delay), recalculating... 373M loops per second, delay more than 10% too short (got 83% of expected delay), recalculating... 364M loops per second, delay more than 10% too short (got 82% of expected delay), recalculating... 359M loops per second, 10 myus = 8 us, 100 myus = 80 us, 1000 myus = 798 us, 10000 myus = 9481 us, 4 myus = 3 us, OK. Initializing internal programmer No coreboot table found. dmidecode execution unsuccessful - continuing without DMI info Found chipset "Intel NM10" with PCI ID 8086:27bc. Enabling flash write... 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x4 0x7fffffff/0x7fffffff FWH IDSEL: 0x5 0x7fffffff/0x7fffffff FWH IDSEL: 0x6 0x7fffffff/0x7fffffff FWH IDSEL: 0x7 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0xa WARNING: Setting 0xdc from 0xa to 0xb on NM10 failed. New value is 0xa. Root Complex Register Block address = 0xfed1c000 GCS = 0x200465: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3020 0x00: 0x8004 (SPIS) 0x02: 0x4130 (SPIC) 0x04: 0x00000000 (SPIA) 0x08: 0x00140000 (SPID0) 0x0c: 0x00000000 (SPID0+4) 0x10: 0x00000000 (SPID1) 0x14: 0x00000000 (SPID1+4) 0x18: 0xeb4150bf (SPID2) 0x1c: 0x0000001d (SPID2+4) 0x20: 0x00000000 (SPID3) 0x24: 0x00000000 (SPID3+4) 0x28: 0xffff0434 (SPID4) 0x2c: 0xffffff50 (SPID4+4) 0x30: 0x00000000 (SPID5) 0x34: 0x00000000 (SPID5+4) 0x38: 0x8be9090f (SPID6) 0x3c: 0x000000f8 (SPID6+4) 0x40: 0x00000000 (SPID7) 0x44: 0xffff0000 (SPID7+4) 0x50: 0x00000000 (BBAR) 0x54: 0x0006 (PREOP) 0x56: 0x103b (OPTYPE) 0x58: 0x05200302 (OPMENU) 0x5c: 0x0001009f (OPMENU+4) 0x60: 0x00000000 (PBR0) 0x64: 0x00000000 (PBR1) 0x68: 0x00000000 (PBR2) WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DF641, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080A, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF010, 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Chip status register is 00 Found Winbond flash chip "W25Q80" (1024 kB, SPI) at physical address 0xfff00000. Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4014 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Found Winbond flash chip "W25Q80" (1024 kB, SPI). Restoring MMIO space at 0x7fb1c2a0a070 Restoring PCI config space for 00:1f:0 reg 0xdc Found chipset "Intel NM10". Enabling flash write... WARNING: Setting 0xdc from 0xa to 0xb on NM10 failed. New value is 0xa. WARNING: SPI Configuration Lockdown activated. PROBLEMS, continuing anyway Found Winbond flash chip "W25Q80" (1024 kB, SPI) at physical address 0xfff00000. Error: Image size doesn't match

2 4

Support MB Gigabyte GA-EP31-DS3L
by Vít Škaban 27 Jan '12

27 Jan '12

Chips: W28X80 and SST25VF080B Vendor: Gigabyte Mainboard: GA-EP31-DS3L Required option: none Status: OK Thank you for this program. It was very helful for me in reparing laptop BIOS via this mainboard. Vit Skraban Czech Republic EU

2 3

ASUS M4N78 PRO -- flashrom -V
by Pavel Stehlík 24 Jan '12

24 Jan '12

Bios written and read sueccessfully. (On Xubuntu 11.10 Oneiric) Thanks for your work on this utility, Pavel Stehlik. P.S. : Possibility to rewrite Macronix_MX25L8005 status register (user value, 00->FF or something like that) would be welcome. I wont to write-protect my BIOS and besides connecting pin 3(!WP) to gnd, setting of some bits of SR is neccessary.

2 1

Re: [flashrom] Chip SST25VF040 @ flashrom v0.9.4-r1486
by Stefan Tauner 24 Jan '12

24 Jan '12

On Sun, 22 Jan 2012 11:33:52 +0100 Marc Kolly <marc.kolly(a)googlemail.com> wrote: > flashrom v0.9.4-r1486 on Linux 2.6.32-37-generic-pae (i686), built with > […] > Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xbf, id2 0x44 > Chip status register is 00 > Chip status register: Block Protect Write Disable (BPL) is not set > Chip status register: Auto Address Increment Programming (AAI) is not set > Chip status register: Bit 5 / Block Protect 3 (BP3) is not set > Chip status register: Bit 4 / Block Protect 2 (BP2) is not set > Chip status register: Bit 3 / Block Protect 1 (BP1) is not set > Chip status register: Bit 2 / Block Protect 0 (BP0) is not set > Chip status register: Write Enable Latch (WEL) is not set > Chip status register: Write In Progress (WIP/BUSY) is not set > […] > This flash part has status UNTESTED for operations: ERASE WRITE […] > Reading flash... done. Hello Marc, thanks for your report! Your log does only show a successful read, but this was already tested for this chip. Did you also try erase and write? If you have not and plan to, please store the backup you made with -r safely. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

abit A-S78H: flashrom -V
by Prakash Punnoor 24 Jan '12

24 Jan '12

Hi, after some intial confusion I can confirm that flashrom works nicely on my motherboard. Cheers, Prakash Dumps: flashrom -V flashrom v0.9.4-r1395 on Linux 3.3.0-rc1+ (x86_64), built with libpci 3.1.7, GCC 4.5.2, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1596M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10000 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "." DMI string system-product-name: "." DMI string system-version: "." DMI string baseboard-manufacturer: "http://www.abit.com.tw/" DMI string baseboard-product-name: "A-S78H(RS780+SB700)" DMI string baseboard-version: "1.x " DMI string chassis-type: "Desktop" Found chipset "AMD SB700/SB710/SB750/SB850" with PCI ID 1002:439d. Enabling flash write... SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=0, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=0, SpiBridgeDisable=0, DropOneClkOnRd=0 NormSpeed is 33 MHz GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK SB700 IMC is not active. ROM strap override is not active OK. This chipset supports the following protocols: LPC, FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L8005" (1024 kB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF010.REMS, 128 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A.RES, 512 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x8a, id2 0xba, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x67, id2 0x6c, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x13 No operations were specified. lspci -nnvvxxx 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 64 Region 3: Memory at <ignored> (64-bit, non-prefetchable) Capabilities: [c4] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00 Link Frequency 0: [b] Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [54] HyperTransport: UnitID Clumping Capabilities: [40] HyperTransport: Retry Mode Capabilities: [9c] HyperTransport: #1a Capabilities: [f8] HyperTransport: #1c 00: 22 10 00 96 06 00 30 22 00 00 00 06 00 40 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 e0 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 c4 00 00 00 00 00 00 00 00 00 00 00 40: 08 9c 00 c0 c1 00 00 00 00 00 00 00 42 20 05 00 50: 7b 14 05 a7 08 40 00 90 08 10 05 00 08 00 cc 51 60: 7f 00 00 00 00 00 00 00 00 02 20 00 09 80 8e 81 70: 00 00 00 00 00 00 00 00 70 23 0f 00 00 00 00 20 80: 00 00 00 00 10 00 00 03 20 01 00 00 33 26 00 00 90: 00 00 00 d8 7f 00 00 00 00 00 00 00 08 f8 7c d0 a0: 26 00 74 00 00 00 00 80 00 00 00 00 79 01 40 05 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 80 08 54 80 01 20 00 11 11 d0 00 00 00 d0: 60 0b 75 1c 02 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 0c 02 00 00 00 00 00 0f f0: 00 00 00 00 00 80 80 00 08 00 00 e0 00 00 00 00 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fdc00000-fddfffff Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00: 22 10 02 96 07 00 30 02 00 00 04 06 00 63 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 44 e1 e1 20 02 20: c0 fd d0 fd 01 d8 f1 df 00 00 00 00 00 00 00 00 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 08 00 40: 00 00 00 00 08 b0 03 a8 00 00 00 00 22 10 02 96 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 0d 00 00 00 22 10 02 96 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:09.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 4) [1022:9608] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fdb00000-fdbfffff Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #9, PowerLimit 25.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4151 Capabilities: [b0] Subsystem: ABIT Computer Corp. Device [147b:a705] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [110 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport 00: 22 10 08 96 07 04 10 00 00 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 d1 d1 00 00 20: b0 fd b0 fd a1 fd a1 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 03 c8 00 00 00 00 10 a0 42 01 20 80 00 00 60: 10 08 00 00 12 0c 30 00 40 00 11 70 80 0c 4c 00 70: 00 00 48 01 00 00 01 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 05 b0 01 00 0c f0 e0 fe 51 41 00 00 00 00 00 00 b0: 0d b8 00 00 7b 14 05 a7 08 00 03 a8 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 ff ff ff ff 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #10, PowerLimit 25.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4159 Capabilities: [b0] Subsystem: ABIT Computer Corp. Device [147b:a705] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [110 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport 00: 22 10 09 96 07 04 10 00 00 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 c1 c1 00 00 20: f0 fd f0 fd e1 fd e1 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 03 c8 00 00 00 00 10 a0 42 01 20 80 00 00 60: 10 08 00 00 12 0c 30 01 40 00 11 70 80 0c 54 00 70: 00 00 48 01 00 00 01 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 05 b0 01 00 0c f0 e0 fe 59 41 00 00 00 00 00 00 b0: 0d b8 00 00 7b 14 05 a7 08 00 03 a8 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 ff ff ff ff 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0]) Subsystem: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 96, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 43 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/4 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4169 Capabilities: [70] SATA HBA v1.0 InCfgSpace Kernel driver in use: ahci 00: 02 10 91 43 07 00 30 02 00 01 06 01 10 60 00 00 10: 01 ff 00 00 01 fe 00 00 01 fd 00 00 01 fc 00 00 20: 01 fb 00 00 00 f0 02 fe 00 00 00 00 02 10 91 43 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00 40: 10 00 00 20 01 00 10 00 00 00 20 01 00 00 00 00 50: 05 70 85 00 0c f0 e0 fe 00 00 00 00 69 41 00 00 60: 01 50 22 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 12 00 10 00 0f 00 00 00 10 03 00 00 00 00 00 00 80: 00 00 00 00 06 00 00 2c 1a 80 b4 01 1a 80 b4 01 90: 1a 80 b4 01 1a 80 b4 01 1a 80 b4 01 1a 80 b4 01 a0: ef a0 ef a0 ef a0 ef a0 ef a0 ef a0 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 20 00 00 e0: 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 49 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41a9 Kernel driver in use: ohci_hcd 00: 02 10 97 43 06 00 b0 02 00 10 03 0c 10 40 80 00 10: 00 e0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 d0 00 00 00 00 00 00 00 07 01 00 00 40: 80 00 00 00 11 00 00 00 00 00 00 00 00 00 00 00 50: 40 13 01 f0 00 00 00 00 ff ff ff ff 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 ff 00 00 80 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 05 00 01 00 0c f0 e0 fe a9 41 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 50 Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41b1 Kernel driver in use: ohci_hcd 00: 02 10 98 43 06 00 b0 02 00 10 03 0c 10 40 00 00 10: 00 d0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 d0 00 00 00 00 00 00 00 07 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 05 00 01 00 0c f0 e0 fe b1 41 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 47 Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4189 Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd 00: 02 10 96 43 16 00 b0 02 00 20 03 0c 10 40 00 00 10: 00 c0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 1e 98 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 01 00 00 08 e0 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 01 d0 02 7e 00 00 40 00 00 00 00 00 00 00 00 00 d0: 05 e4 01 00 0c f0 e0 fe 89 41 00 00 00 00 00 00 e0: 00 00 00 00 0a 00 e0 20 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 51 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41b9 Kernel driver in use: ohci_hcd 00: 02 10 97 43 06 00 b0 02 00 10 03 0c 10 40 80 00 10: 00 b0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 d0 00 00 00 00 00 00 00 05 01 00 00 40: 80 00 00 00 11 00 00 00 00 00 00 00 00 00 00 00 50: 40 13 01 f0 00 00 00 00 ff ff ff ff 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 ff 00 00 80 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 05 00 01 00 0c f0 e0 fe b9 41 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 52 Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41c1 Kernel driver in use: ohci_hcd 00: 02 10 98 43 06 00 b0 02 00 10 03 0c 10 40 00 00 10: 00 a0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 d0 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 05 00 01 00 0c f0 e0 fe c1 41 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 48 Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4199 Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd 00: 02 10 96 43 16 00 b0 02 00 20 03 0c 10 40 00 00 10: 00 90 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 c0 00 00 00 00 00 00 00 03 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 1e 98 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 01 00 00 08 e0 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 01 d0 02 7e 00 00 40 00 00 00 00 00 00 00 00 00 d0: 05 e4 01 00 0c f0 e0 fe 99 41 00 00 00 00 00 00 e0: 00 00 00 00 0a 00 e0 20 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ 00: 02 10 85 43 03 04 30 02 3a 00 05 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00 40: 44 7b 00 fc 00 00 00 00 0f ff 00 00 00 00 00 80 50: f0 01 f0 00 f0 00 f0 00 21 0b 78 8f 00 00 00 00 60: 01 00 24 20 bf fc de 02 7f 90 00 00 20 00 00 00 70: 00 00 00 00 08 00 c0 fe ff 6e 00 00 00 00 f0 0f 80: f0 0a f0 0f 00 00 00 00 00 00 00 00 00 00 00 00 90: 01 0b 00 00 f9 ce ff 00 00 00 00 00 00 00 00 00 a0: 00 00 ff ff 7f ff f0 09 00 ff 22 02 16 71 20 18 b0: 08 00 02 a8 00 00 d0 fe 00 00 00 00 f0 0f 08 1a c0: 09 60 e0 df 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 20 b9 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: d8 0c 00 00 00 00 44 00 00 00 00 00 fe 00 30 00 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: I/O ports at 1000 [size=8] Region 1: I/O ports at 1010 [size=4] Region 2: I/O ports at 1008 [size=8] Region 3: I/O ports at 1014 [size=4] Region 4: I/O ports at fa00 [size=16] Capabilities: [70] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4171 Kernel driver in use: pata_atiixp 00: 02 10 9c 43 05 00 30 02 00 8f 01 01 10 40 00 00 10: 01 10 00 00 11 10 00 00 09 10 00 00 15 10 00 00 20: 01 fa 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 70 00 00 00 00 00 00 00 ff 01 00 00 40: 5d 20 5d 5d ff 20 ff ff 00 00 04 00 00 00 00 00 50: 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 60: 00 00 40 24 10 2c 01 07 01 00 00 00 ff ff 0f 00 70: 05 00 01 00 0c f0 e0 fe 71 41 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 53 Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 41c9 Kernel driver in use: snd_hda_intel 00: 02 10 83 43 06 04 10 04 00 00 03 04 10 40 00 00 10: 04 40 02 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00 40: 00 00 02 00 01 01 00 00 00 00 00 00 01 00 00 00 50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 00 81 00 0c f0 e0 fe 00 00 00 00 c9 41 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: 02 10 9d 43 0f 00 20 02 00 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 04 00 00 00 d5 ff 03 ff 3f ff 40 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 02 00 00 00 00 0f 00 b8 ff ff ff 70: 67 45 23 00 00 00 00 00 1d 00 00 00 05 0b 00 00 80: 08 00 03 a8 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00 00 a0: 02 00 c1 fe 2f 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 e9 f2 ff 00 00 c0: 00 00 00 00 00 00 08 00 f7 ff ff ff 00 00 00 78 d0: 00 ff ff 00 00 00 00 ff ff ff ff 00 00 00 00 0c e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=04, subordinate=04, sec-latency=64 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fd900000-fd9fffff Prefetchable memory behind bridge: fd800000-fd8fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [54] HyperTransport: MSI Mapping Enable+ Fixed+ 00: 02 10 84 43 27 00 b0 02 00 01 04 06 00 40 81 00 10: 00 00 00 00 00 00 00 00 00 04 04 40 b0 b0 80 22 20: 90 fd 90 fd 80 fd 80 fd 00 00 00 00 00 00 00 00 30: 00 00 00 00 54 00 00 00 00 00 00 00 00 00 00 00 40: 2e 00 0c ff 00 00 00 00 0c 0f 3c d1 00 01 00 00 50: 01 00 00 00 08 00 03 a8 00 00 00 00 85 00 ff ff 60: ca 0e 17 00 ba d8 10 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 06 e0: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: [b] Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- 00: 22 10 00 12 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00 50: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00 60: 00 00 03 00 e0 00 00 00 20 a8 2e 01 00 f8 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 00 01 21 20 20 11 11 60 0b f5 8f 13 00 00 00 90: d0 02 85 80 00 00 00 00 07 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 27 01 00 00 00 00 01 00 00 00 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00 80: 03 0a 00 00 00 0b 00 00 00 00 00 00 00 00 00 00 90: 03 00 d8 00 00 ff df 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 03 00 f0 00 00 02 fe 00 b0: 03 00 e0 00 80 4f e0 00 00 00 00 00 00 00 00 00 c0: 13 b0 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 03 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 f0: 03 28 00 d8 00 00 00 00 00 00 00 00 00 00 00 00 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 00 00 00 01 01 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: e0 3e 78 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 06 00 48 0f 00 00 00 00 80: 05 00 00 00 00 00 00 00 24 fa 7c 5d 45 03 22 00 90: 10 04 01 00 0b 80 58 7f 07 42 00 8d 00 00 00 00 a0: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: eb 6d 32 a6 4e 00 00 00 2e 3a 32 0a d6 88 24 93 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 22 fb c8 52 79 53 ac 89 06 c7 96 0c a2 7d 64 01 e0: 6c c1 d9 13 56 71 d0 e6 71 3f eb 80 6d 5f 48 54 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k10temp 00: 22 10 03 12 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: 00 01 00 00 5c 00 b0 4a 00 00 00 00 00 00 00 00 50: ee 1d 40 9a 93 4c 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 04 00 24 34 00 00 00 30 51 80 01 60 70: 51 11 32 60 01 01 98 00 14 0c 20 00 0d 08 07 00 80: 81 e6 00 e6 e6 41 e6 01 08 00 00 00 00 40 40 00 90: 43 00 00 00 66 00 00 00 00 77 1b 01 00 00 00 00 a0: 00 08 1c a0 80 18 88 10 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 39 c5 04 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 26 0f 81 c8 16 18 00 03 28 63 47 01 e0: 00 00 00 00 30 1a 40 1c 59 7f 07 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 53 0f 10 00 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 04 12 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780 [Radeon HD 3200] [1002:9610] (prog-if 00 [VGA controller]) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at ee00 [size=256] Region 2: Memory at fddf0000 (32-bit, non-prefetchable) [size=64K] Region 5: Memory at fdc00000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: radeon Kernel modules: radeon 00: 02 10 10 96 07 00 10 00 00 00 00 03 10 00 80 00 10: 08 00 00 d8 01 ee 00 00 00 00 df fd 00 00 00 00 20: 00 00 00 00 00 00 c0 fd 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 50: 01 a0 03 06 00 00 00 00 10 a0 12 00 a0 8f 00 00 60: 10 08 0a 00 01 0d 00 00 00 00 01 11 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 1f 00 00 00 80: 00 00 00 00 00 00 00 00 01 00 01 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. TEG-ECTX Gigabit PCI-E Adapter [Trendnet] [10ec:8168] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 46 Region 0: I/O ports at de00 [size=256] Region 2: Memory at fdbff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fda00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Vital Product Data Unknown small resource type 05, will not decode more. Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4181 Capabilities: [60] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [12c v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [148 v1] Device Serial Number 45-12-00-00-10-ec-81-68 Capabilities: [154 v1] Power Budgeting <?> Kernel driver in use: r8169 00: ec 10 68 81 07 04 10 00 01 00 00 02 10 00 00 00 10: 01 de 00 00 00 00 00 00 04 f0 bf fd 00 00 00 00 20: 00 00 00 00 00 00 00 00 02 01 00 00 ec 10 68 81 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00 40: 01 48 c2 f7 00 00 00 00 03 50 00 00 29 81 ec 10 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 81 41 00 00 60: 10 84 01 00 23 7f 00 00 10 58 1a 00 41 f4 03 00 70: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 09 00 4c 01 01 1c 02 00 fb ff ff 11 90: 08 30 00 00 7f e2 0f 00 8f a0 03 00 c3 00 00 00 a0: 02 28 ff 01 00 00 00 00 00 08 00 00 03 00 03 00 b0: 00 00 00 00 ff 3f ff 3f ff ff 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI- E Gigabit Ethernet Controller [11ab:4364] (rev 14) Subsystem: ABIT Computer Corp. Device [147b:a705] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at ce00 [size=256] [virtual] Expansion ROM at fde00000 [disabled] [size=128K] Capabilities: [48] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Product Name: Marvell Yukon 88E8056 Gigabit Ethernet Controller Read-only fields: [PN] Part number: Yukon 88E8056 [EC] Engineering changes: Rev. 1.4 [MN] Manufacture ID: 4d 61 72 76 65 6c 6c [SN] Serial number: AbCdEfG0439C2 [CP] Extended capability: 01 10 cc 03 [RV] Reserved: checksum good, 9 byte(s) reserved Read/write fields: [RW] Read-write area: 121 byte(s) free End Capabilities: [5c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4179 Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 1f, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: sky2 00: ab 11 64 43 07 04 10 00 14 00 00 02 10 00 00 00 10: 04 c0 ff fd 00 00 00 00 01 ce 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 05 a7 30: 00 00 00 00 48 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 f0 01 00 80 a0 01 01 50 03 fe 00 20 00 13 50: 03 5c fc 80 00 00 00 78 00 00 34 01 05 e0 81 00 60: 0c f0 e0 fe 00 00 00 00 79 41 00 00 00 00 00 00 70: 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 70 00 00 00 00 00 00 82 a8 e8 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 10 00 11 00 c0 8f 64 00 00 20 19 00 11 ac 07 01 f0: 48 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00 superiotool -deV superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xc000, id=0x23a0 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0xa023, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0xa023 Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0xa023, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627DHG (id=0xa0, rev=0x23) at 0x2e Register dump: idx 02 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f val ff a0 23 ff 00 c0 00 00 ff 50 00 7c 00 ea 00 00 ff def 00 a0 NA ff 00 MM 00 MM RR 50 00 00 RR e2 21 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 00 00 00 00 04 0e 00 ff 00 00 def 01 03 f0 06 02 8e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 00 00 00 00 04 3f def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 00 00 00 00 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 00 00 00 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 83 def 01 00 60 00 64 01 0c 83 LDN 0x06 (Serial peripheral interface) idx 30 62 63 val 00 ff ff def 00 00 00 LDN 0x07 (GPIO 6) idx 30 f4 f5 f6 f7 val 06 ff ff ff ff def 00 ff 00 00 00 LDN 0x08 (WDTO#, PLED) idx 30 f5 f6 f7 val 01 00 00 00 def 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5) idx 30 e0 e1 e2 e3 e4 e5 e6 e7 e8 e9 f0 f1 f2 f3 f4 f5 f6 f7 fe val 07 ff ff ff ff 0c 00 00 e3 ff ff 9c 80 63 00 20 a4 db 00 00 def 00 ff 00 00 ff 00 00 00 00 00 00 ff 00 00 00 ff 00 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 e8 e9 f2 f3 f4 f6 f7 fe val 00 00 00 00 12 24 00 00 0c 00 09 00 7d 00 00 00 08 00 def 00 00 01 00 ff 08 00 RR 1c 00 RR RR 7c 00 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 f1 f2 val 01 02 90 02 81 ff 81 def 00 00 00 00 81 00 00 LDN 0x0c (PECI, SST) idx e0 e1 e2 e3 e4 e5 e8 f1 fe ff val 00 48 48 48 48 00 00 48 ff ff def 00 48 48 48 48 00 00 48 00 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for VIA Super I/O at 0x3f0... PCI device 1106:0686 not found. Probing for AMD EC Super I/O at 0xaa... Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff Probing for Infineon Super I/O at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for Infineon Super I/O at 0x4e... Failed. Returned data: id=0xff, rev=0xff

2 1

Re: [flashrom] Difference of factory bios and dumped image
by Prakash Punnoor 23 Jan '12

23 Jan '12

On Saturday 31 December 2011 13:55:45 Idwer Vollering wrote: > 2011/12/31 Prakash Punnoor <prakashp(a)arcor.de>: > > On 31.12.2011 11:39, Paul Menzel wrote: > >> Am Samstag, den 31.12.2011, 10:55 +0100 schrieb Prakash Punnoor: > >>> flashrom kind of works on my system, but not with the factory > >>> images. If I read it out with flashrom and write it back with > >>> flashrom (also to a different chip) it works. The sizes of factory > >>> and dumped image are same but they are somewhat binary different. > >>> Any idea? The motherboard is Abit A-S78H. As I am playing around > >>> with coreboot - so far unsuccessfully - I want to know whether > >>> flashrom is writing the generated image correctly... I can upload > >>> both images somewhere if interested. This is flashrom output on my > >>> system: > >>> > >>> > >>> flashrom v0.9.4-r1395 on Linux 3.2.0-rc7+ (x86_64), built with > >>> libpci 3.1.7, GCC 4.5.2, little endian > >>> flashrom is free software, get the source code at > >>> http://www.flashrom.org > >>> > >>> Calibrating delay loop... OK. > >>> Found chipset "AMD SB700/SB710/SB750/SB850". Enabling flash write... > >>> OK. This chipset supports the following protocols: LPC, FWH, SPI. > >>> Found Macronix flash chip "MX25L8005" (1024 kB, SPI) at physical > >>> address 0xfff00000. > >>> No operations were specified. > >> > >> Unfortunately this question seems not be listed in the FAQ. Most of > >> the > >> time some areas differ because the MAC address and other configuration > >> data of the downloaded images differs [2]. I hope you mean the > >> downloaded image by factory/vendor image. > > > > To clarify: > > - Image I got from vendor web page: Flashed with flashrom won't work > > (machine doesn't POST). Flashed with awdflash works. > > Is the bootblock in the downloaded image intact/present? You can use > bios_extract: http://cgit.freedesktop.org/~libv/bios_extract > > What happens when you reset the CMOS/ESCD data after flashing with > flashrom? awdflash does that with the /cp parameter, see > http://www.plasma-online.de/textual/howto/flash_award.html For what is worth, I tried flashing dumped file and then factory bios on top. this worked, so I guess everythign is alright. I'l send a separate mail for inclusion in wiki. Regards, Prakash

1 0

Chip SST25VF040 @ flashrom v0.9.4-r1486
by Marc Kolly 22 Jan '12

22 Jan '12

flashrom v0.9.4-r1486 on Linux 2.6.32-37-generic-pae (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1823M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 982 us, 10000 myus = 10131 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "LENOVO" DMI string system-product-name: "898573G" DMI string system-version: "ThinkCentre M55E" DMI string baseboard-manufacturer: "LENOVO" DMI string baseboard-product-name: "LENOVO" DMI string baseboard-version: "Not Specified" DMI string chassis-type: "Mini Tower" Found ITE Super I/O, ID 0x8718 on port 0x2e Found chipset "Intel ICH7/ICH7R" with PCI ID 8086:27b8. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 Root Complex Register Block address = 0xfed1c000 GCS = 0x464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3020 0x00: 0x0004 (SPIS) 0x02: 0x7f10 (SPIC) 0x04: 0x0007ffc0 (SPIA) 0x08: 0x27c88086 (SPID0) 0x0c: 0x0000ffff (SPID0+4) 0x10: 0xd5b00000 (SPID1) 0x14: 0x27c98086 (SPID1+4) 0x18: 0x0000ffff (SPID2) 0x1c: 0xd5ba0000 (SPID2+4) 0x20: 0x27ca8086 (SPID3) 0x24: 0x0000ffff (SPID3+4) 0x28: 0xd5c40000 (SPID4) 0x2c: 0x27cb8086 (SPID4+4) 0x30: 0x0000ffff (SPID5) 0x34: 0xd5ce0000 (SPID5+4) 0x38: 0x00e1f5e9 (SPID6) 0x3c: 0x00000000 (SPID6+4) 0x40: 0x00e260ea (SPID7) 0x44: 0x000000f0 (SPID7+4) 0x50: 0x00000000 (BBAR) 0x54: 0x5006 (PREOP) 0x56: 0x463b (OPTYPE) 0x58: 0x05d80302 (OPMENU) 0x5c: 0xc79f0190 (OPMENU+4) 0x60: 0x00000000 (PBR0) 0x64: 0x00000000 (PBR1) 0x68: 0x00000000 (PBR2) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching disabled, caching enabled, OK. No IT87* serial flash segment enabled. The following protocols are supported: SPI. Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xbf, id2 0x44 Chip status register is 00 Chip status register: Block Protect Write Disable (BPL) is not set Chip status register: Auto Address Increment Programming (AAI) is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found SST flash chip "SST25VF040" (512 kB, SPI) at physical address 0xfff80000. === This flash part has status UNTESTED for operations: ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -VE, -Vw), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... done. Restoring MMIO space at 0xb7787070 Restoring MMIO space at 0xb778707c Restoring MMIO space at 0xb7787078 Restoring MMIO space at 0xb7787076 Restoring MMIO space at 0xb7787074

1 0

Re: [flashrom] Mainboard no tested
by Stefan Tauner 21 Jan '12

21 Jan '12

hello again this looks like it needs way more work than i thought in the beginning. the flash chip is probably behind the super i/o chip (fintek F71882) which flashrom does not yet support. there has been a patch in the works for a long time, but i think there was not much demand/testers to finish it. could you please apply the following patch to r1455 of flashrom, recompile, run flashrom -V and send us the log? http://patchwork.coreboot.org/patch/3440/ this will *not* enable you to use flashrom as a programmer, but it might induce further development. i think it is safe to test (no flash access is done). i will inform the author of the patch that a new victim^Wtester arrived ;) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

3 2

successfull Flash log [was Re: [PATCH] Add board enable for AOpen D2544-B1 (used in FCS ESPRIMO Q5010)]
by Oliver Rath 19 Jan '12

19 Jan '12

Hi stefan, Ive added a verbose log of flash the esprimo machine. The flashing with the modified bios runs, but the additional functionality seems hidden. Regards, Oliver

2 1

[commit] r1486 - trunk
by repository service 19 Jan '12

19 Jan '12

Author: stefanct Date: Thu Jan 19 18:50:32 2012 New Revision: 1486 URL: http://flashrom.org/trac/flashrom/changeset/1486 Log: Add board enable for AOpen i945GMx-VFX (used in FCS ESPRIMO Q5010) Typical AWARD enable structure with an ICH GPIO board enable. This board seems also to be known as D2544-B1. Success report: http://www.flashrom.org/pipermail/flashrom/2012-January/008590.html Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Tested-by: Oliver Rath <rath(a)mglug.de> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Thu Jan 12 14:58:43 2012 (r1485) +++ trunk/board_enable.c Thu Jan 19 18:50:32 2012 (r1486) @@ -1560,6 +1560,16 @@ /* * Suited for: + * - AOpen i945GMx-VFX: Intel 945GM + ICH7-M used in ... + * - FCS ESPRIMO Q5010 (SMBIOS: D2544-B1) + */ +static int intel_ich_gpio38_raise(void) +{ + return intel_ich_gpio_set(38, 1); +} + +/* + * Suited for: * - ASUS M6Ne (laptop): socket 479M (guessed) + Intel 855PM + ICH4-M */ static int intel_ich_gpio43_raise(void) @@ -2098,6 +2108,7 @@ {0x1106, 0x3177, 0x17F2, 0x3177, 0x1106, 0x3148, 0x17F2, 0x3148, NULL, NULL, NULL, P3, "Albatron", "PM266A Pro", 0, OK, w836xx_memw_enable_2e}, {0x1022, 0x2090, 0, 0, 0x1022, 0x2080, 0, 0, NULL, "artecgroup", "dbe61", P3, "Artec Group", "DBE61", 0, OK, board_artecgroup_dbe6x}, {0x1022, 0x2090, 0, 0, 0x1022, 0x2080, 0, 0, NULL, "artecgroup", "dbe62", P3, "Artec Group", "DBE62", 0, OK, board_artecgroup_dbe6x}, + {0x8086, 0x27b9, 0xa0a0, 0x0632, 0x8086, 0x27da, 0xa0a0, 0x0632, NULL, NULL, NULL, P3, "AOpen", "i945GMx-VFX", 0, OK, intel_ich_gpio38_raise}, {0x8086, 0x277c, 0xa0a0, 0x060b, 0x8086, 0x27da, 0xa0a0, 0x060b, NULL, NULL, NULL, P3, "AOpen", "i975Xa-YDG", 0, OK, board_aopen_i975xa_ydg}, {0x8086, 0x27b8, 0x1849, 0x27b8, 0x8086, 0x27da, 0x1849, 0x27da, "^ConRoeXFire-eSATA2", NULL, NULL, P3, "ASRock", "ConRoeXFire-eSATA2", 0, OK, intel_ich_gpio16_raise}, {0x1039, 0x0741, 0x1849, 0x0741, 0x1039, 0x5513, 0x1849, 0x5513, "^K7S41 $", NULL, NULL, P3, "ASRock", "K7S41", 0, OK, w836xx_memw_enable_2e}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Thu Jan 12 14:58:43 2012 (r1485) +++ trunk/print.c Thu Jan 19 18:50:32 2012 (r1486) @@ -556,6 +556,7 @@ B("Advantech", "PCM-5820", 1, "http://www.emacinc.com/sbc_pc_compatible/pcm_5820.htm", NULL), B("agami", "Aruma", 1, "http://web.archive.org/web/20080212111524/http://www.agami.com/site/ais-600…", NULL), B("Albatron", "PM266A Pro", 1, "http://www.albatron.com.tw/English/Product/MB/pro_detail.asp?rlink=Overview…", NULL), /* FIXME */ + B("AOpen", "i945GMx-VFX", 1, NULL, "This is (also?) an OEM board from FCS (used in e.g. ESPRIMO Q5010 with designation D2544-B1)."), B("AOpen", "vKM400Am-S", 1, "http://usa.aopen.com/products_detail.aspx?Auno=824", NULL), B("Artec Group","DBE61", 1, "http://wiki.thincan.org/DBE61", NULL), B("Artec Group","DBE62", 1, "http://wiki.thincan.org/DBE62", NULL),

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom