flashrom

flashrom@flashrom.org

3 participants
9188 discussions

[PATCH] dediprog: Use asynchronous bulk transfers for reading
by Nico Huber 16 Nov '12

16 Nov '12

This utilizes libusb-1.0's interface for asynchronous transfers. A read is split into 512 byte chunks as required by the dediprog hardware. Up to eight chunks are scheduled for asynchronous transfer which results in a viable speed-up. First tests have shown a three times speed increase. It's based on "Bump dediprog driver to use libusb-1.0". Signed-off-by: Nico Huber <nico.huber(a)secunet.com> diff --git a/dediprog.c b/dediprog.c index a558285..f1c03d8 100644 --- a/dediprog.c +++ b/dediprog.c @@ -29,6 +29,7 @@ #define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 +#define DEDIPROG_ASYNC_TRANSFERS 8 /* at most 8 asynchronous transfers */ static libusb_context *usb_ctx; static libusb_device_handle *dediprog_handle; static int dediprog_firmwareversion; @@ -176,6 +177,38 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) return 0; } +struct dediprog_transfer_status { + int status; /* OK if 0, ERROR else */ + unsigned int queued_idx; + unsigned int finished_idx; +}; + +static void dediprog_bulk_read_cb(struct libusb_transfer *const transfer) +{ + struct dediprog_transfer_status *const status = (struct dediprog_transfer_status *)transfer->user_data; + if (transfer->status != LIBUSB_TRANSFER_COMPLETED) { + status->status = 1; + msg_perr("SPI bulk read failed!\n"); + } + ++status->finished_idx; +} + +static int dediprog_bulk_read_poll(const struct dediprog_transfer_status *const status, const int finish) +{ + if (status->finished_idx >= status->queued_idx) + return 0; + + do { + struct timeval timeout = { 10, 0 }; + const int ret = libusb_handle_events_timeout_completed(usb_ctx, &timeout, NULL); + if (ret < 0) { + msg_perr("Polling read events failed: %i %s!\n", ret, libusb_error_name(ret)); + return 1; + } + } while (finish && (status->finished_idx < status->queued_idx)); + return 0; +} + /* Bulk read interface, will read multiple 512 byte chunks aligned to 512 bytes. * @start start address * @len length @@ -184,7 +217,7 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len) { - int ret, transferred; + int ret, err = 1; unsigned int i; /* chunksize must be 512, other sizes will NOT work at all. */ const unsigned int chunksize = 0x200; @@ -194,6 +227,10 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, chunksize & 0xff, (chunksize >> 8) & 0xff }; + struct dediprog_transfer_status status = { 0, 0, 0 }; + struct libusb_transfer *transfers[DEDIPROG_ASYNC_TRANSFERS] = { NULL, }; + struct libusb_transfer *transfer; + if ((start % chunksize) || (len % chunksize)) { msg_perr("%s: Unaligned start=%i, len=%i! Please report a bug " "at flashrom(a)flashrom.org\n", __func__, start, len); @@ -214,17 +251,54 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, return 1; } - for (i = 0; i < count; i++) { - ret = libusb_bulk_transfer(dediprog_handle, 0x80 | dediprog_endpoint, - buf + i * chunksize, chunksize, &transferred, DEFAULT_TIMEOUT); - if ((ret < 0) || (transferred != chunksize)) { - msg_perr("SPI bulk read %i failed, expected %i, got %i %s!\n", - i, chunksize, ret, libusb_error_name(ret)); - return 1; + /* + * Ring buffer of bulk transfers. + * Poll until at least one transfer is ready, + * schedule next transfers until buffer is full. + */ + + /* Allocate bulk transfers. */ + for (i = 0; i < min(DEDIPROG_ASYNC_TRANSFERS, count); ++i) { + transfers[i] = libusb_alloc_transfer(0); + if (!transfers[i]) { + msg_perr("Allocating libusb transfer %i failed: %s!\n", i, libusb_error_name(ret)); + goto _err_free; } } - return 0; + /* Now transfer requested chunks using libusb's asynchronous interface. */ + while (status.queued_idx < count) { + while ((status.queued_idx - status.finished_idx) < DEDIPROG_ASYNC_TRANSFERS) { + transfer = transfers[status.queued_idx % DEDIPROG_ASYNC_TRANSFERS]; + libusb_fill_bulk_transfer(transfer, dediprog_handle, 0x80 | dediprog_endpoint, + (unsigned char *)buf + status.queued_idx * chunksize, chunksize, + dediprog_bulk_read_cb, &status, DEFAULT_TIMEOUT); + transfer->flags |= LIBUSB_TRANSFER_SHORT_NOT_OK; + ret = libusb_submit_transfer(transfer); + if (ret < 0) { + msg_perr("Submitting SPI bulk read %i failed: %i %s!\n", + status.queued_idx, ret, libusb_error_name(ret)); + goto _err_free; + } + ++status.queued_idx; + } + if (dediprog_bulk_read_poll(&status, 0)) + goto _err_free; + } + /* Wait for transfers to finish. */ + if (dediprog_bulk_read_poll(&status, 1)) + goto _err_free; + /* Check if everything has been transmitted. */ + if ((status.finished_idx < count) || status.status) + goto _err_free; + + err = 0; + +_err_free: + dediprog_bulk_read_poll(&status, 1); + for (i = 0; i < DEDIPROG_ASYNC_TRANSFERS; ++i) + if (transfers[i]) libusb_free_transfer(transfers[i]); + return err; } static int dediprog_spi_read(struct flashctx *flash, uint8_t *buf,

1 0

Re: [flashrom] Intel DH67CL verbose log
by Stefan Tauner 16 Nov '12

16 Nov '12

On Thu, 15 Nov 2012 20:31:18 +0200 Ville Herva <vherva(a)gmail.com> wrote: > Ripping the battery off for a good while helped, and I was able to upgrade > the BIOS at POST. usually there is also a jumper (CMOS or NVRAM reset) that does the same. > Anyway, it would be cool to be able to flash BIOS from Linux. that is (or was) the goal of course, but intel (and microsoft) try to block access to the flash chip more and more to have more control over what the user can run. they try to sell this as a security feature, but that is only a part of it. if it would be about security only, then the user would be in control. in the secure boot scheme on x86 machines the user IS in control about the boot loader certificates, but this is only out of fear of competition laws IMHO. ATM it IS possible to flash the BIOS region, even if other regions are locked. we just do not know if it is safe in all cases or if the management engine interferes (as this is not documented anywhere publicly) and hence give the warnings. in the future (i.e. starting with the haswell family of processors) flashrom will most probably be crippled even more on these platforms according to recently leaked information. so... nag intel please, not us ;) see also http://blogs.coreboot.org/blog/2011/08/17/gsoc-2011-flashrom-part-5-–-dear-… -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] [PATCH] Add Altera USB-Blaster SPI programmer.
by Kyösti Mälkki 16 Nov '12

16 Nov '12

On Mon, 2012-10-29 at 01:33 +0100, Stefan Tauner wrote: > Adds support for the Altera USB-Blaster programming dongle in > Active Serial (AS) mode. > Tested on both original product and a clone dongle. > > Signed-off-by: James Laird <jhl(a)mafipulation.org> > Signed-off-by: Kyösti Mälkki <kyosti.malkki(a)gmail.com> > Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> > --- > > Rebased on Kyösti's version. > Fixed Makefile and whitespace, cleaned up a few things, > added a manpage... please retest on hardware. > > Can someone please explain to me why send_read() does what it does? > Thanks, your clean-up looks good. Tested on both a clone with C8051F321 and the original product. The blaster design is described here: http://sourceforge.net/apps/mediawiki/urjtag/index.php?title=Cable_Altera_U… As for send_read(), to read a byte from SPI, one must first write a byte to the USB. Stupid, but that is the design. This hardware has particularly bad performance penalty when reading in small chunks of pagesize or 256 bytes. With non-blocking bulk submits in libusb-1.0, the raw read speed can be increased by factor of 2 for clone and by 5 for original product. Regards, KM

2 1

Re: [flashrom] Intel DH67CL verbose log
by Stefan Tauner 15 Nov '12

15 Nov '12

On Tue, 6 Nov 2012 22:09:13 +0200 Ville Herva <vherva(a)gmail.com> wrote: > 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. > 0x58: 0x03ff0185 FREG1: BIOS region (0x00185000-0x003fffff) is read-write. > 0x5C: 0x01840003 FREG2: WARNING: Management Engine region (0x00003000-0x00184fff) is locked. Hello Ville, thanks for your report! The problem is the locked ME region as quoted above and the SMM protection, which is both not trivial to work around, sorry. I have added the board to our list of (un)supported boards (with an appropriate note) and will commit that later together with other small changes. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Re: [flashrom] Shuttle XPC SB61G2 (FB61 mainboard) success!
by Stefan Tauner 15 Nov '12

15 Nov '12

On Sat, 3 Nov 2012 23:55:35 -0600 Lineage <lineage2005(a)gmail.com> wrote: > http://www.shuttle.eu/_archive/older/en/sb61g2.htm > This appears to be the machine based on case identifiers. > Mainboard and BIOS identifiers make it out as an FB61: > http://www.shuttle.eu/_archive/older/en/fb61.htm#mainboardfb6 > > No required switches beyond normal operations. > > Successfully wrote a new BIOS from the Manufacturer on two "identical" > systems. Only captured the log of the second machine, silly me, but the > first looked the same (at least results-wise. :D) Hello, thanks for your report! I have added your board to our list of supported hardware and will commit that later together with other small changes. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

AT25DF321A Support
by Christophe Fauvel 14 Nov '12

14 Nov '12

Hello, I am using an FT2232H mini module for flashing an AT25DF321A SPI flash under linux (Ubuntu 10.10, kernel 2.6.35-32-generic), which is supported according to your Supported Hardware list. I have tested several flashrom revisions (v0.9.2 pré-compiled, v0.9.5 and V0.9.6.xx compiled with GCC 4.4.5). * with rev0.9.2, the device is listed as UNTESTED when reading, writing or erasing. I have multiple errors when accessing the device but I can read, write and erase small amount of data. * with rev0.9.5, I also have some issues with the device, but with a few retries I am able to fully read, write and erase the chip, which is also listed as UNTESTED. * with rev0.9.6, however, the device is listed as Unknown SPI chip and I cannot access it. Have you already noticed this issue ? Best regards, -- Christophe Fauvel GOOBIE Tel: +336 76 63 93 25 +331 75 45 80 62 Mail: christophe.fauvel(a)goobie.fr Adresse: 23 avenue Louis Bréguet, Santos Dumont, 78140 Vélizy-Villacoublay FRANCE

2 1

Need help with failed flash
by simon 13 Nov '12

13 Nov '12

Flashrom: Your flash chip is in an unknown state. chipset "SiS 650" with PCI ID 1039:0650. Any sugestions please? ---- # dmidecode --type bios: <begin> # dmidecode 2.11 SMBIOS 2.3 present. Handle 0x0000, DMI type 0, 20 bytes BIOS Information Vendor: American Megatrends Inc. Version: 07.00T Release Date: 04/02/01 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 256 kB Characteristics: ISA is supported PCI is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/360 kB floppy services are supported (int 13h) 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported AGP is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Handle 0x0016, DMI type 13, 22 bytes BIOS Language Information Language Description Format: Abbreviated Installable Languages: 4 English Traditional Chinese Simplified Chinese Japanese Currently Installed Language: Not Specified <end> verbose output from flashrom: <begin> #flashrom -Vw a9280820.rom flashrom v0.9.5.2-r1517 on Linux 3.2.0-32-generic-pae (i686), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 34 usecs, 1040M loops per second, delay more than 10% too short (got 87% of expected delay), recalculating... 1187M loops per second, 10 myus = 11 us, 100 myus = 123 us, 1000 myus = 1025 us, 10000 myus = 10095 us, 136 myus = 269 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Elitegroup Co. " DMI string system-product-name: "i-Buddie " DMI string system-version: "1.0 " DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "Ref.NO:A928-020313-OT-01-00-10-FF$" DMI string baseboard-version: "2.0 " DMI string chassis-type: "Desktop" Found chipset "SiS 650" with PCI ID 1039:0650. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Found southbridge 1039:0961 at 00:02:0 OK. The following protocols are supported: Non-SPI. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0x29, id2 0xf3, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x9c, id2 0x7a, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Found Winbond flash chip "W49F002U/N" (256 kB, Parallel) at physical address 0xfffc0000. Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xda, id2 0x0b Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W49F002U/N" (256 kB, Parallel). Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x01ffff:EW, 0x020000-0x037fff:EW, 0x038000-0x039fff:E, 0x03a000-0x03bfff:E, 0x03c000-0x03ffff:EERASE FAILED at 0x0003c000! Expected=0xff, Read=0x9c, failed byte count from 0x0003c000-0x0003ffff: 0x3f1f ERASE FAILED! Reading current flash chip contents... done. Looking for another erase function. Trying erase function 1... 0x000000-0x03ffff:EERASE FAILED at 0x0003c000! Expected=0xff, Read=0x9c, failed byte count from 0x00000000-0x0003ffff: 0x3f1f ERASE FAILED! Looking for another erase function. No usable erase functions left. FAILED! Uh oh. Erase/write failed. Checking if anything changed. Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! Restoring PCI config space for 00:02:0 reg 0x45 Restoring PCI config space for 00:02:0 reg 0x40 <end>

1 0

[PATCH] autotest mode
by Carl-Daniel Hailfinger 11 Nov '12

11 Nov '12

This patch needs the following changes to be mergeable: - layout support - man page - message printing cosmetics Autotest mode tests all usable erase functions of a flash chip with a few test patterns, then restores the original flash contents. To make sure you can recover the original flash chip contents even if the autotest run is aborted, you have to specify a filename parameter for --autotest where the flash chip contents are saved. Example usage: flashrom -p dummy:emulate=SST25VF032B --output autotest.log --autotest scratch.img Please note that autotest uses roughly 10 erase cycles per usable erase function and repeated usage will cause serious flash wear. Speed isn't really good even with dummy, and I expect a 8 Mbit SPI chip on a real fast programmer to take at least 10 minutes for autotest (10*erasefn+1 all-sectors chip write, 10*erasefn+1.all-sectors erase, 30*erasefn+2 all-sectors read). The patch seems to work, at least during my tests with dummy. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-autotest/flash.h =================================================================== --- flashrom-autotest/flash.h (Revision 1622) +++ flashrom-autotest/flash.h (Arbeitskopie) @@ -239,7 +239,7 @@ void print_banner(void); void list_programmers_linebreak(int startcol, int cols, int paren); int selfcheck(void); -int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, int verify_it); +int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, int verify_it, int autotest_it); int read_buf_from_file(unsigned char *buf, unsigned long size, const char *filename); int write_buf_to_file(unsigned char *buf, unsigned long size, const char *filename); Index: flashrom-autotest/cli_classic.c =================================================================== --- flashrom-autotest/cli_classic.c (Revision 1622) +++ flashrom-autotest/cli_classic.c (Arbeitskopie) @@ -118,17 +118,18 @@ #if CONFIG_PRINT_WIKI == 1 int list_supported_wiki = 0; #endif - int read_it = 0, write_it = 0, erase_it = 0, verify_it = 0; + int read_it = 0, write_it = 0, erase_it = 0, verify_it = 0, autotest_it = 0; int dont_verify_it = 0, list_supported = 0, operation_specified = 0; enum programmer prog = PROGRAMMER_INVALID; int ret = 0; - static const char optstring[] = "r:Rw:v:nVEfc:l:i:p:Lzho:"; + static const char optstring[] = "r:Rw:v:a:nVEfc:l:i:p:Lzho:"; static const struct option long_options[] = { {"read", 1, NULL, 'r'}, {"write", 1, NULL, 'w'}, {"erase", 0, NULL, 'E'}, {"verify", 1, NULL, 'v'}, + {"autotest", 1, NULL, 'a'}, {"noverify", 0, NULL, 'n'}, {"chip", 1, NULL, 'c'}, {"verbose", 0, NULL, 'V'}, @@ -196,6 +197,15 @@ filename = strdup(optarg); verify_it = 1; break; + case 'a': + if (++operation_specified > 1) { + fprintf(stderr, "More than one operation " + "specified. Aborting.\n"); + cli_classic_abort_usage(); + } + filename = strdup(optarg); + autotest_it = 1; + break; case 'n': if (verify_it) { fprintf(stderr, "--verify and --noverify are" @@ -506,7 +516,7 @@ goto out_shutdown; } - if (!(read_it | write_it | verify_it | erase_it)) { + if (!(read_it || write_it || verify_it || erase_it || autotest_it)) { msg_ginfo("No operations were specified.\n"); goto out_shutdown; } @@ -520,7 +530,7 @@ * Give the chip time to settle. */ programmer_delay(100000); - ret |= doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it); + ret |= doit(fill_flash, force, filename, read_it, write_it, erase_it, verify_it, autotest_it); /* Note: doit() already calls programmer_shutdown(). */ goto out; Index: flashrom-autotest/dediprog.c =================================================================== --- flashrom-autotest/dediprog.c (Revision 1622) +++ flashrom-autotest/dediprog.c (Arbeitskopie) @@ -34,17 +34,6 @@ #define DEDI_SPI_CMD_PAGEWRITE 0x1 #define DEDI_SPI_CMD_AAIWRITE 0x4 -#if 0 -/* Might be useful for other pieces of code as well. */ -static void print_hex(void *buf, size_t len) -{ - size_t i; - - for (i = 0; i < len; i++) - msg_pdbg(" %02x", ((uint8_t *)buf)[i]); -} -#endif - /* Might be useful for other USB devices as well. static for now. */ static struct usb_device *get_device_by_vid_pid(uint16_t vid, uint16_t pid) { Index: flashrom-autotest/flashrom.c =================================================================== --- flashrom-autotest/flashrom.c (Revision 1622) +++ flashrom-autotest/flashrom.c (Arbeitskopie) @@ -448,6 +448,14 @@ return i; } +void print_hex(void *buf, size_t len) +{ + size_t i; + + for (i = 0; i < len; i++) + msg_pdbg(" %02x", ((uint8_t *)buf)[i]); +} + void tolower_string(char *str) { for (; *str != '\0'; str++) @@ -873,6 +881,9 @@ case 13: memset(buf, 0xff, size); break; + default: + msg_gerr("Invalid pattern %i\n", variant); + return 1; } if ((variant >= 0) && (variant <= 7)) { @@ -1328,8 +1339,7 @@ return 0; } -int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, - uint8_t *newcontents) +int erase_and_write_flash(struct flashctx *flash, uint8_t *oldcontents, uint8_t *newcontents) { int k, ret = 1; uint8_t *curcontents; @@ -1720,12 +1730,59 @@ return 0; } +int autotest_flash(struct flashctx *flash) +{ + const int patternlist[] = {0, 4, 2, 5, 1, 3, 8, 9, 13, 12}; + unsigned long size = flash->chip->total_size * 1024; + int erasefn, pattern, ret = 0; + uint8_t *oldcontents, *newcontents; + + oldcontents = malloc(size); + if (!oldcontents) { + msg_gerr("Out of memory!\n"); + exit(1); + } + newcontents = malloc(size); + if (!newcontents) { + msg_gerr("Out of memory!\n"); + exit(1); + } + msg_cinfo("Starting autotest.\n"); + /* outer loop: erase functions, inner loop: test patterns */ + for (erasefn = 0; erasefn < NUM_ERASEFUNCTIONS; erasefn++) { + msg_cdbg("Trying erase function %i... ", erasefn); + if (check_block_eraser(flash, erasefn, 1)) + continue; + for (pattern = 0; pattern < ARRAY_SIZE(patternlist); pattern++) { + msg_cinfo("Reading current flash chip contents... "); + if (flash->chip->read(flash, oldcontents, 0, size)) { + msg_cinfo("FAILED.\n"); + return 1; + } + msg_cinfo("done.\n"); + msg_cinfo("Erasing and writing flash chip... "); + if (generate_testpattern(newcontents, size, patternlist[pattern])) { + msg_gerr("Pattern %i generation failed!\n", patternlist[pattern]); + continue; + } + msg_ginfo("Writing pattern %i:\n", patternlist[pattern]); + print_hex(newcontents, 16); + ret |= walk_eraseregions(flash, erasefn, &erase_and_write_block_helper, oldcontents, + newcontents); + /* Work around chips which need some time to calm down. */ + programmer_delay(1000*1000); + ret |= verify_range(flash, newcontents, 0, size); + } + } + return ret; +} + /* This function signature is horrible. We need to design a better interface, * but right now it allows us to split off the CLI code. * Besides that, the function itself is a textbook example of abysmal code flow. */ -int doit(struct flashctx *flash, int force, const char *filename, int read_it, - int write_it, int erase_it, int verify_it) +int doit(struct flashctx *flash, int force, const char *filename, int read_it, int write_it, int erase_it, + int verify_it, int autotest_it) { uint8_t *oldcontents; uint8_t *newcontents; @@ -1744,9 +1801,11 @@ if (flash->chip->unlock) flash->chip->unlock(flash); - if (read_it) { + if (read_it || autotest_it) { ret = read_flash_to_file(flash, filename); - goto out_nofree; + /* Only quit if we are doing a pure read. */ + if (read_it) + goto out_nofree; } oldcontents = malloc(size); @@ -1802,14 +1861,27 @@ } #endif } + if (autotest_it) { + //FIXME: We completely ignore layouts in autotest mode. + autotest_flash(flash); + /* Restore original contents. */ + if (read_buf_from_file(newcontents, size, filename)) { + /* FIXME: Proper error message. */ + ret = 1; + goto out; + } + msg_ginfo("Restoring original chip contents:"); + } + + /* Read the whole chip to be able to check whether regions need to be * erased and to give better diagnostics in case write fails. * The alternative would be to read only the regions which are to be * preserved, but in that case we might perform unneeded erase which * takes time as well. */ - msg_cinfo("Reading old flash chip contents... "); + msg_cinfo("Reading current flash chip contents... "); if (flash->chip->read(flash, oldcontents, 0, size)) { ret = 1; msg_cinfo("FAILED.\n"); @@ -1817,17 +1889,19 @@ } msg_cinfo("done.\n"); - // This should be moved into each flash part's code to do it - // cleanly. This does the job. - handle_romentries(flash, oldcontents, newcontents); + /* All included romentries will be written. In autotest mode, included + * romentries will be tested with the patterns, the rest will be left + * alone. + */ + if (!autotest_it) + handle_romentries(flash, oldcontents, newcontents); - // //////////////////////////////////////////////////////////// - - if (write_it) { + if (write_it || autotest_it) { if (erase_and_write_flash(flash, oldcontents, newcontents)) { msg_cerr("Uh oh. Erase/write failed. Checking if " "anything changed.\n"); - if (!flash->chip->read(flash, newcontents, 0, size)) { + /* If this is the restore step of autotest, we want to complain in any case. */ + if (!autotest_it && !flash->chip->read(flash, newcontents, 0, size)) { if (!memcmp(oldcontents, newcontents, size)) { msg_cinfo("Good. It seems nothing was " "changed.\n"); @@ -1842,10 +1916,10 @@ } } - if (verify_it) { + if (verify_it || autotest_it) { msg_cinfo("Verifying flash... "); - if (write_it) { + if (write_it || autotest_it) { /* Work around chips which need some time to calm down. */ programmer_delay(1000*1000); ret = verify_range(flash, newcontents, 0, size); -- http://www.hailfinger.org/

2 2

Hi!
by santia.v.v 07 Nov '12

07 Nov '12

Hi! I was testing flashrom and trying tu update my BIOS and I got some problems, I entered the irc chat and very kind people helped me to send you the information you need to look at it: Here is the problem output: Here is the image for the update: http://download.gigabyte.eu/FileList/BIOS/motherboard_bios_ga-8i848p775g_f4… Here you have the output of 'flashrom -p internal -V', 'lspci -nnvvvxxx', 'superiotool -deV' : cat bios.txt flashrom v0.9.5.2-r1515 on Linux 3.6.6-gentoo (i686), built with libpci 3.1.10, GCC 4.5.4, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 4 usecs, 127M loops per second, delay more than 10% too short (got 53% of expected delay), recalculating... 166M loops per second, delay more than 10% too short (got 8% of expected delay), recalculating... 2138M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1007 us, 10000 myus = 10092 us, 16 myus = 17 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "8I848P775-G" DMI string baseboard-version: "x.x" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "Intel ICH5/ICH5R" with PCI ID 8086:24d0. Enabling flash write... BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: FWH. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Found SST flash chip "SST49LF002A/B" (256 kB, FWH) at physical address 0xfffc0000. Lock status for 0x000000 (size 0x004000) is 00, full access Lock status for 0x004000 (size 0x004000) is 00, full access Lock status for 0x008000 (size 0x004000) is 00, full access Lock status for 0x00c000 (size 0x004000) is 00, full access Lock status for 0x010000 (size 0x004000) is 00, full access Lock status for 0x014000 (size 0x004000) is 00, full access Lock status for 0x018000 (size 0x004000) is 00, full access Lock status for 0x01c000 (size 0x004000) is 00, full access Lock status for 0x020000 (size 0x004000) is 00, full access Lock status for 0x024000 (size 0x004000) is 00, full access Lock status for 0x028000 (size 0x004000) is 00, full access Lock status for 0x02c000 (size 0x004000) is 00, full access Lock status for 0x030000 (size 0x004000) is 00, full access Lock status for 0x034000 (size 0x004000) is 00, full access Lock status for 0x038000 (size 0x004000) is 00, full access Lock status for 0x03c000 (size 0x004000) is 00, full access Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x25, id2 0xbe, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x57 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xbf, id2 0x57 Found SST flash chip "SST49LF002A/B" (256 kB, FWH). No operations were specified. Restoring PCI config space for 00:1f:0 reg 0x4e 00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:2570] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Capabilities: [e4] Vendor Specific Information: Len=06 <?> Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Kernel driver in use: agpgart-intel 00: 86 80 70 25 06 01 90 20 02 00 00 06 00 00 00 00 10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 70 25 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 02 08 00 40 80 1c 00 00 00 00 00 00 00 00 00 60: 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 11 00 00 00 00 00 00 00 00 00 00 0a 38 00 a0: 02 00 30 00 1b 4a 00 1f 02 03 00 00 00 00 00 00 b0: 80 00 00 00 20 00 00 00 00 00 8c 35 10 10 00 00 c0: 00 00 00 00 00 80 0e 28 00 00 00 00 00 00 00 00 d0: 02 28 04 0e 0b 0d 00 00 00 00 00 00 00 00 20 01 e0: 00 00 00 00 09 a0 06 21 06 02 00 00 00 00 00 00 f0: 00 00 00 00 02 00 00 00 68 0f 03 00 00 00 00 00 00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P AGP Bridge [8086:2571] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: f8000000-f9ffffff Prefetchable memory behind bridge: e0000000-efffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 71 25 07 00 a0 00 02 00 04 06 00 40 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 20 90 90 a0 22 20: 00 f8 f0 f9 00 e0 f0 ef 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00 00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K] 00: 86 80 76 25 02 00 80 00 02 00 80 08 00 00 00 00 10: 00 00 cf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 43 65 10 04 00 00 00 00 04 00 00 00 00 00 00 00 50: 01 00 80 00 02 01 80 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 55 05 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 20 08 00 b0: 00 00 00 00 f0 43 fc 7d 01 00 00 00 09 00 00 00 c0: 00 08 00 00 20 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 ff ff ff ff ff ff ff 3f e0: 01 00 00 00 00 00 01 02 ff 0e 00 00 00 00 04 00 f0: 00 0c 02 00 00 00 00 00 68 0f 03 00 74 fc 00 00 00:1d.0 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000/8KNXP motherboard [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bc00 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 bc 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.1 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at b000 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b0 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.2 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at b400 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b4 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.3 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at b800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b8 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1d.7 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ehci_hcd 00: 86 80 dd 24 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 00 00 fc 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 06 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 c2 c9 00 80 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 c0 70: 00 00 d7 3f 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 55 55 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 80 00 00 88 83 40 00 66 0f 05 00 06 14 00 00 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 80000000-800fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 4e 24 07 00 80 00 c2 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 a0 a0 80 22 20: 00 fa f0 fb 00 80 00 80 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 40: 02 28 30 76 00 00 00 00 00 00 00 00 00 00 00 00 50: 26 64 73 00 00 00 00 00 50 01 34 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 b8 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 4f 35 00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 10 00 00 10 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 81 10 00 00 10 00 00 00 60: 8c 89 8b 8a d0 00 00 00 8a 80 80 8b 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 75 54 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 20 02 00 00 00 00 00 00 0d 00 00 00 00 03 00 00 b0: 00 00 00 00 00 00 00 00 55 65 55 59 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 80 08 00 30 00 00 d0: 86 21 02 00 02 0f 00 00 04 00 00 00 00 00 00 00 e0: 10 00 00 c0 00 00 0f 34 33 22 11 00 00 00 67 45 f0: 00 00 62 00 04 00 00 00 66 0f 05 3e 00 00 00 00 00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d1] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 Region 4: I/O ports at f000 [size=16] Kernel driver in use: ata_piix 00: 86 80 d1 24 05 00 a8 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 20: 01 f0 00 00 00 00 00 00 00 00 00 00 58 14 d1 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40: 07 a3 03 e3 00 00 00 00 05 00 01 02 00 00 00 00 50: 00 00 00 00 f0 10 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 04 00 13 00 20 00 00 00 00 00 00 00 00 00 00 00 a0: 68 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02) Subsystem: Giga-byte Technology GA-8IPE1000 Pro2 motherboard (865PE) [1458:24d2] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 1400 [size=32] Kernel driver in use: i801_smbus 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 14 00 00 00 00 00 00 00 00 00 00 58 14 d2 24 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 02 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV635 PRO AGP [Radeon HD 3650] [1002:9596] (prog-if 00 [VGA controller]) Subsystem: Hightech Information System Ltd. Device [1787:0028] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at f9000000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at f8000000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 Kernel driver in use: radeon 00: 02 10 96 95 07 00 b0 02 00 00 00 03 08 20 00 00 10: 08 00 00 e0 01 90 00 00 00 00 00 f9 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 28 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 01 08 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 28 00 50: 01 58 03 06 00 00 00 00 02 00 30 00 1b 02 00 ff 60: 02 43 00 1f 01 0d 00 00 00 00 01 11 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:03.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 0a) Subsystem: Creative Labs Live! 5.1 Digital [SB0228] [1102:8066] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at a000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: snd_emu10k1 Kernel modules: snd-emu10k1 00: 02 11 02 00 05 00 90 02 0a 00 01 04 00 20 80 00 10: 01 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 66 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0c 01 02 14 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 06 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:03.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 0a) Subsystem: Creative Labs Gameport Joystick [1102:0020] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Region 0: I/O ports at a400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 70 05 00 90 02 0a 00 80 09 00 20 80 00 10: 01 a4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 06 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:04.0 Ethernet controller [0200]: Atheros Communications Inc. AR2413/AR2414 Wireless Network Adapter [AR5005G(S) 802.11bg] [168c:001a] (rev 01) Subsystem: Accton Technology Corporation Device [1113:4211] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: ath5k Kernel modules: ath5k 00: 8c 16 1a 00 06 00 90 02 01 00 00 02 08 a8 00 00 10: 00 00 00 fb 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 01 50 00 00 13 11 11 42 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 0a 1c 40: 00 00 00 00 01 00 c2 01 00 40 00 c6 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02:09.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13) Subsystem: Giga-byte Technology Marvell 88E8001 Gigabit Ethernet Controller (Gigabyte) [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fb010000 (32-bit, non-prefetchable) [size=16K] Region 1: I/O ports at a800 [size=256] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=7 DScale=1 PME- Capabilities: [50] Vital Product Data Product Name: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter Read-only fields: [PN] Part number: Yukon 88E8001 [EC] Engineering changes: Rev. 1.3 [MN] Manufacture ID: 4d 61 72 76 65 6c 6c [SN] Serial number: AbCdEfG4f7639 [CP] Extended capability: 01 10 cc 03 [RV] Reserved: checksum good, 10 byte(s) reserved Read/write fields: [RW] Read-write area: 121 byte(s) free End Kernel driver in use: skge 00: ab 11 20 43 07 00 b0 02 13 00 00 02 08 40 00 00 10: 00 00 01 fb 01 a8 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 00 e0 30: 00 00 00 00 48 00 00 00 00 00 00 00 0a 01 17 1f 40: 00 00 f0 05 00 80 a0 01 01 50 02 fe 00 2e 00 0c 50: 03 00 fc 80 00 00 00 78 00 00 04 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Found ITE IT8712F (id=0x8712, rev=0x5) at 0x2e Register dump: idx 20 21 22 23 24 2b val 87 12 05 00 00 00 def 87 12 08 00 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 00 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 f1 f2 f3 val 01 03 f8 04 00 50 00 7f def 00 03 f8 04 00 50 00 7f LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 01 02 f8 03 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 70 74 f0 val 01 03 78 00 00 07 04 08 def 00 03 78 07 78 07 03 03 LDN 0x04 (Environment controller) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 01 02 90 00 00 00 80 00 0a 00 00 00 ff def 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 71 f0 val 01 00 60 00 64 01 02 68 def 01 00 60 00 64 01 02 08 LDN 0x06 (Mouse) idx 30 70 71 f0 val 00 00 02 00 def 00 0c 02 00 LDN 0x07 (GPIO) idx 25 26 27 28 29 2a 2c 60 61 62 63 64 65 70 71 72 73 74 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c8 c9 ca cb cc e0 e1 e2 e3 e4 f0 f1 f2 f3 f4 f5 f6 f7 f8 f9 fa fb fc fd val 01 00 20 01 a1 00 00 00 00 08 00 00 00 00 00 00 00 04 00 00 00 00 00 00 01 00 20 01 21 21 01 00 00 00 20 01 00 00 00 20 00 00 00 00 00 10 40 00 00 00 28 1d 00 00 00 00 00 1f 00 def 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40 00 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 03 00 0a 00 def 00 03 00 0a 00 LDN 0x09 (Game port) idx 30 60 61 val 00 02 01 def 00 02 01 LDN 0x0a (Consumer IR) idx 30 60 61 70 f0 val 00 03 10 0b 06 def 00 03 10 0b 00 Environment controller (0x0295) Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff

1 1

Intel DH67CL verbose log
by Ville Herva 06 Nov '12

06 Nov '12

Seems not to be supported. -- v -- v(a)iki.fi

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom