flashrom September 2016

flashrom@flashrom.org

16 participants
24 discussions

Re: [flashrom] Issue programming SPI flash
by Stefan Tauner 21 Sep '16

21 Sep '16

On Tue, 20 Sep 2016 23:00:15 +0000 Steve Burks <steve.burks(a)us.kontron.com> wrote: > Hi, > I have been flashing Macronix SPI with device ID MX25L12805D. We now have a new Numonyx SPI with device ID N25Q128..3E. However, when I try to flash the device it says that no flash device was found. But when I do the -p internal it clearly shows the device ID N25Q128..3E > > I have attached the verbose output from when I ran the command. I appreciate any assistance that you can provide. > > Thank you. > > Stephen Burks Hi Stephen, you have a Winbond W25Q128 there. All of these three are interchangeable so I guess someone swapped it without telling you :) In any case you should not use the -c parameter unless you have to and really know what chip is on there. Without it flashrom will find the right chip itself if it can. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Issue programming SPI flash
by Steve Burks 20 Sep '16

20 Sep '16

Hi, I have been flashing Macronix SPI with device ID MX25L12805D. We now have a new Numonyx SPI with device ID N25Q128..3E. However, when I try to flash the device it says that no flash device was found. But when I do the -p internal it clearly shows the device ID N25Q128..3E I have attached the verbose output from when I ran the command. I appreciate any assistance that you can provide. Thank you. Stephen Burks Manager, Manufacturing Engineering - USA Manufacturing Engineering and Material Data Management Kontron 14118 Stowe Drive | Poway, CA 92064 | USA P: + 1 (858) 677-0877 x3266 | M: + 1 (858) 699-4690 Steve.Burks(a)us.kontron.com<mailto:Steve.Burks@us.kontron.com> Website<http://www.kontron.com/> | Blog<http://blog.kontron.com/> | Twitter<https://twitter.com/Kontron> | LinkedIn<https://www.linkedin.com/company/kontron> | YouTube<https://www.youtube.com/channel/UCXkp_1gJbG0Um1vzdowlqww> | Facebook<https://www.facebook.com/kontron> Kontron America Please find our mandatory legal statements here<http://www.kontron.com/additional/disclaimer>. By opening this email you are agreeing to Kontron's Electronic Communications Policy<http://www.kontron.com/additional/legal-and-copyright-information>.

1 0

[PATCH] add board enable for apple iMac5,2
by Arthur Heymans 19 Sep '16

19 Sep '16

Hi This patch adds the apple iMac5,2 to board enable. The hardware is very similar to the apple macbook2,1.

2 4

untested chipset intel
by Jan van Roessel 19 Sep '16

19 Sep '16

Marked as untested chipset Intel NUC, see attached log Met vriendelijke groet, Jan van Roessel

1 0

testing my A7V333
by Elmar Stellnberger 17 Sep '16

17 Sep '16

Today I have also tested my A7V333 mainboard with the latest flashrom from svn; and see it could read an image (log in the attachement). It said that write and erase would still need to be tested; however the following message does not raise my confidence: Changing lock bits failed at 0xb7305002! New value: 0xff. Basically I would also be ready to test erase & write on this board though it would likely be a good idea to have the error/log messages checked first.

1 2

Unable to detect SPI-Flash connected to RT5350 using flashrom.
by Pradeep Ch 17 Sep '16

17 Sep '16

We are using flashrom tool to program SPI flash on a RT5350 chipset board. We are able to program if we directly connect Jtag to the SPI -Serial Flash. The RT5350 has a Jtag interface pins. Can we connect a Jtag connector to connect to this interface and program SPI-Serial flash using flashrom. Rgds, Pradeep Ch.

1 0

Re: [flashrom] W836xx: L372N1 / GC Frontman (flashrom: unknown reg 0x20 ID: ea)
by Elmar Stellnberger 14 Sep '16

14 Sep '16

Here come the message files for erase & write: P.S.: re-sent to the mailinglist from 2016-09-11 since I did not get a response by Jim for some days. Am 2016-09-11 um 12:57 schrieb Elmar Stellnberger: > Hi Jim Rowan, > Hi Readers of the Flashrom List, > > Today I have re-tried it with the newest flashrom and the patch at > http://patchwork.coreboot.org/patch/4127 > - and see it worked (attachement). > > board name: Gericom Frontman, L372N1 ( EON EN29F040A ) > > Regards, > Elmar > > > Am 2016-09-02 um 23:04 schrieb Elmar Stellnberger: >> Today I have tried flashrom on a rather old L372N1 computer (PIV 2,8Ghz, >> GC Frontman): >> ------------------------------------------------------------ >> flashrom v0.9.7-r1711 on Linux 3.14.50-std460-i586 (i686) >> flashrom is free software, get the source code at http://www.flashrom.org >> >> Calibrating delay loop... OK. >> Active config mode, unknown reg 0x20 ID: ea. >> Please send the output of "flashrom -V" to >> flashrom(a)flashrom.org with W836xx: your board name: flashrom -V >> as the subject to help us finish support for your Super I/O. Thanks. >> Found chipset "SiS 645DX". Enabling flash write... OK. >> No EEPROM/flash device found. >> Note: flashrom can never write if the flash chip isn't found >> automatically. >> ------------------------------------------------------------ >> >> The BIOS Chip on the mainboard can be accessed easily; it is placed >> inside a special hanger and appears to be replacable. There is a sticker >> on the BIOS Chip saying: >> >> 686 >> AMIBIOS >> NBEC(c)2000 >> BA31 >> 8603 >> >> installed BIOS: Amibios v1.54, 10/15/2003, Version 1.08G >> >> The current BIOS there has some disadvantages like support with old >> style disks up to a maximum of 160GB (manual Cylinder-Head-Sector >> configuration); today I have tried it with a 64GB SSD IDE disk and the >> BIOS can not boot from it ( CD + floppy boot is o.k.). >> >> How do you believe are the chances to get flashrom running on that >> machine or to exchange the BIOS with a newer one? >> >> Elmar >> >> >> P.S.: I have attached some more information about the system as I was >> unsure which one would help you.

1 0

W836xx: L372N1 / GC Frontman (flashrom: unknown reg 0x20 ID: ea)
by Elmar Stellnberger 14 Sep '16

14 Sep '16

Today I have tried flashrom on a rather old L372N1 computer (PIV 2,8Ghz, GC Frontman): ------------------------------------------------------------ flashrom v0.9.7-r1711 on Linux 3.14.50-std460-i586 (i686) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Active config mode, unknown reg 0x20 ID: ea. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found chipset "SiS 645DX". Enabling flash write... OK. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. ------------------------------------------------------------ The BIOS Chip on the mainboard can be accessed easily; it is placed inside a special hanger and appears to be replacable. There is a sticker on the BIOS Chip saying: 686 AMIBIOS NBEC(c)2000 BA31 8603 installed BIOS: Amibios v1.54, 10/15/2003, Version 1.08G The current BIOS there has some disadvantages like support with old style disks up to a maximum of 160GB (manual Cylinder-Head-Sector configuration); today I have tried it with a 64GB SSD IDE disk and the BIOS can not boot from it ( CD + floppy boot is o.k.). How do you believe are the chances to get flashrom running on that machine or to exchange the BIOS with a newer one? Elmar P.S.: I have attached some more information about the system as I was unsure which one would help you.

1 1

[Patch]ignore-read-error
by Tommy.Lo 12 Sep '16

12 Sep '16

Dear Maintainers , This patch is for the following description: Transaction is failed and errors are shown when flashrom try to read region that locked by Intel ME. This patch simply disable code to check error (will read 0xff) then flashrom will continue to read the rest. And only ignore the error when read op. It will output a warning message to stderr like: Transaction (READ) error at address 0x001000-0x7fffff, ignored To avoid a lot of similar error messages, it shows error at end of locked region. Thanks! Sign-off-by: Tommy Lo < tommy.lo(a)advantech.com.tw > Index: ichspi.c =================================================================== --- ichspi.c (revision 1955) +++ ichspi.c (working copy) @@ -178,6 +178,9 @@ static void *ich_spibar = NULL; +/* keep last addr of read error */ +static uint32_t last_read_warn_addr = 0xFFFFFFFF; + typedef struct _OPCODE { uint8_t opcode; //This commands spi opcode uint8_t spi_type; //This commands spi type @@ -946,14 +949,38 @@ /* FIXME make sure we do not needlessly cause transaction errors. */ temp32 = REGREAD32(ICH9_REG_SSFS); if (temp32 & SSFS_FCERR) { - msg_perr("Transaction error!\n"); - prettyprint_ich9_reg_ssfs(temp32); - prettyprint_ich9_reg_ssfc(temp32); - /* keep reserved bits */ - temp32 &= SSFS_RESERVED_MASK | SSFC_RESERVED_MASK; - /* Clear the transaction error. */ - REGWRITE32(ICH9_REG_SSFS, temp32 | SSFS_FCERR); - return 1; + if (ichspi_lock && op.spi_type == SPI_OPCODE_TYPE_READ_WITH_ADDRESS) { + /* keep reserved bits */ + temp32 &= SSFS_RESERVED_MASK | SSFC_RESERVED_MASK; + /* Clear the transaction error. */ + REGWRITE32(ICH9_REG_SSFS, temp32 | SSFS_FCERR); + if (last_read_warn_addr != 0xFFFFFFFF) { + if (last_read_warn_addr == (offset - 1)) { + /* continuing */ + last_read_warn_addr = offset + datalength - 1; + } else { + msg_pdbg("-0x%06x, ignored\n", last_read_warn_addr); + last_read_warn_addr = 0xFFFFFFFF; + } + } else { + msg_pdbg("Transaction (READ) error at address 0x%06x", offset); + last_read_warn_addr = offset + datalength - 1; + } + } else { + prettyprint_ich9_reg_ssfs(temp32); + prettyprint_ich9_reg_ssfc(temp32); + /* keep reserved bits */ + temp32 &= SSFS_RESERVED_MASK | SSFC_RESERVED_MASK; + /* Clear the transaction error. */ + REGWRITE32(ICH9_REG_SSFS, temp32 | SSFS_FCERR); + msg_perr("Transaction error!\n"); + return 1; + } + } else { + if (last_read_warn_addr != 0xFFFFFFFF) { + msg_pdbg("-0x%06x, ignored\n", last_read_warn_addr); + last_read_warn_addr = 0xFFFFFFFF; + } } if ((!write_cmd) && (datalength != 0))

1 0

flashrom stops/hangs
by joshj23 06 Sep '16

06 Sep '16

while trying to flash a chip (winbond W25Q32.v), on a arduino uno r3, the TX and RX led's will be on while flashrom is running normally, but will almost always turn off and flashrom in the terminal will stop all activity any suggestions? -- *Josh*

1 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom September 2016