August 2016 - flashrom - mail.coreboot.org

Re: [flashrom] Writing to a specific Flash region with Layout approach
by Urja Rannikko Aug. 1, 2016

Aug. 1, 2016

Hi, On Mon, Aug 1, 2016 at 10:33 AM, Pradeep Ch <shanmugp(a)sysargus.com> wrote: > > I am attempting to write to a flashrom using layout/region approach. > The NOR flash size is 8MBytes. The file size I am writing is 106976 Bytes. > > The rom.layout file contents are: > 00000000:0001a1df test1 > 0001a1e0:007fffff test2 > > The command I am using is: > ./flashrom -p ft2232_spi:type=arm-usb-ocd --layout rom.layout --image test1 > -w bootloader.img > > The error I am getting is : > Using region: "test1". > Calibrating delay loop... OK. > Found Eon flash chip "EN25Q64" (8192 kB, SPI) on ft2232_spi. > Error: Image size (106976 B) doesn't match the flash chip's size (8388608 > B)! > > Please let me know about the error. The current layout system will only limit the actually written area, not change the requirements of the flash file being the size of the chip, so in this case you'd need to pad the bootloader.img to 8MB.

1 0

Writing to a specific Flash region with Layout approach
by Pradeep Ch Aug. 1, 2016

Aug. 1, 2016

I am attempting to write to a flashrom using layout/region approach. The NOR flash size is 8MBytes. The file size I am writing is 106976 Bytes. The rom.layout file contents are: 00000000:0001a1df test1 0001a1e0:007fffff test2 The command I am using is: ./flashrom -p ft2232_spi:type=arm-usb-ocd --layout rom.layout --image test1 -w bootloader.img The error I am getting is : Using region: "test1". Calibrating delay loop... OK. Found Eon flash chip "EN25Q64" (8192 kB, SPI) on ft2232_spi. Error: Image size (106976 B) doesn't match the flash chip's size (8388608 B)! Please let me know about the error. Thanks, Pradeep Ch.

1 0

Re: [flashrom] Failed to write/read NOR flash EN25Q64 using ARM-USB-OCD Jtag.
by Stefan Tauner Aug. 1, 2016

Aug. 1, 2016

On Sun, 31 Jul 2016 15:34:18 +0530 Pradeep Ch <pradeepsysargus(a)gmail.com> wrote: > favorite > <http://stackoverflow.com/questions/38674226/flashrom-tool-command-has-faile…> > > I am able to detect my flash chip when I use the command: > > ./flashrom -p ft2232_spi:type=arm-usb-ocd -c EN25Q64 > > If use the below command to write binary file to the flash memory using > JTAG - ARM-USB-OCD debugger for my target board RT5350F-OLinuXino-EVB, > > ./flashrom -p ft2232_spi:type=arm-usb-ocd -w > FlashImage_RT5350F_OLinuXino_EVB.bin > > I am getting an error, the error is: > > Found Eon flash chip "EN25Q64" (8192 kB, SPI) on ft2232_spi. > ftdi_write_data: -110, usb bulk write failed > send_buf failed before read: 1 > Reading old flash chip contents... ftdi_read_data: -110, usb bulk read failed > get_buf failed: 1 > FAILED. Do you power the whole setup via the OCD? That might be the culprit. I presume that it can not supply enough current in all operating modes. Apparently it is enough to probe for the chip though... -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1