I don't suppose anyone has any experience updating or fixing MAC addresses on Nvidea nVIDIA MCP55V-Pro (Supermicro H8DMT+) ?
Following an experimental reflash everything went well, except afterwards we noticed the mac address had been reset
link/ether 66:77:44:22:33:12 brd ff:ff:ff:ff:ff:ff
FidoNet - the internet made simple!
10 - 16 Tiller Road, London, E14 8PX
tel: 0845 004 3050 / fax: 0845 004 3051
I was asked by Idwer to look into this. Since the patch was code reviewed
already I have just some comments:
1) does it work if IMC is disabled?
If not, we should first detect if IMC firmware is active.
2) it writes to reserved bits 7:1
This should be easy fix
3) is there a way to release it back after writes are done?
Alternative way would be to send "go to IDLE/ram command to firmware.
I am using Parted Magic Live CD operation system in my laptop.
I want only *READ *information and use command in Konsole: "flashrom -r
ASUS.def.iso -p internal:this_is_not_laptop >> error.txt"
I have get this error file:
flashrom v0.9.6.1-r1564 on Linux 3.7.9-pmagic (i686)
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Found chipset "Intel HM65".
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware
then please email a report to flashrom(a)flashrom.org including a verbose
Enabling flash write... WARNING: BIOS region SMM protection is enabled!
WARNING: SPI Configuration Lockdown activated.
FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is
FREG2: WARNING: Management Engine region (0x00001000-0x0017ffff) is locked.
Please send a verbose log to flashrom(a)flashrom.org if this board is not
Writes have been disabled. You can enforce write support with the
ich_spi_force programmer option, but it will most likely harm your hardware!
If you force flashrom you will get no support if something breaks.
Found Winbond flash chip "W25Q32" (4096 kB, SPI) at physical address
Reading flash... FAILED.
*What is means???*
I have read "Support chipset" in
http://www.flashrom.org/Supported_hardware and saw *"?"* symbol for
Can I read flash in my laptop by your programm (flashrom v0.9.6.1-r1564)?
I ran flashrom on a Thinkpad X301 today with the result of the attached logfile. Just tried to get a dump of the BIOS, no writing intended.
According to the schematics the BIOS chip is connected to the ICH9 only, so I guess reading the flash won't interfere with the EC.
Any idea on how to work around the error?
I'm sending the wireshark capture off list.
On 04/27/2013 04:42 PM, Stefan Tauner wrote:
> On Tue, 23 Apr 2013 10:16:27 -0600
> Marc Jones <marcj303(a)gmail.com> wrote:
>> On Tue, Apr 23, 2013 at 9:21 AM, Joshua Zarr <joshuazarr(a)gmail.com> wrote:
>>> Hi All,
>>> I am using a dediprog SF100 to program the two flash chips (AT25DF321) on an
>>> intel Stargo CRB. Does flashrom support programming each chip individually?
>> I ran into the same thing. I think that the flashrom dediprog support
>> needs a flag to switch the chipselect.
> If anybody could supply us with traces of the USB traffic generated
> when another CS is used, we could probably add support for it. I dont
> know anything about the protocol or the vendor application but I guess
> it would be rather easy to find the interesting bits by creating and
> comparing dumps of two executions (e.g. the probing for a chip if that's
> supported) that differ only in the selected connection.
I am planning to flashrom a *SN68*SG2 2007 shuttle PC. I know its not one
of your supported hardware systems, but it appears that if you can support
fn78 series this should be a no brainier too.
Does anyone have any experience with the SN68 series?
I have time, and I shall wait your reply.